RailKing R-17 Subway Set OPERATOR’S MANUAL Compatibility This engine will operate on any traditional O-31 Gauge track system, including M.T.H.’s RealTrax® or ™ ScaleTrax or traditional tubular track. It is also compatible with most standard AC transformers. (See page 15 for a complete list of compatible transformers and wiring instructions.
Table of Contents Set Up Checklis t................................................................................................... 3 Lubrication.............................................................................................3 Basic Operation .....................................................................................................4 Activating Features.................................................................................4 Loco-Sound Operating Instructions...............
Set Up Checklist • • Lubricate the locomotive Apply power to run as described in the Basic Operating Section of this manual Lubrication You should lubricate the engine to prevent it from squeaking. Use light household oil and follow the lubrication points marked “L” in Fig. 1. Do not over-oil and avoid getting lubricant on flat surface of pickup roller. Use only a drop or two on each pivot point.
Basic Operation Throttle Throttle up the power to your track. Advance the throttle until 12 – 16 volts is applied, then put the subway set into forward motion by either firmly pressing the Direction button on your transformer or remote once or dropping and advancing the throttle. Bell - To sound the bell, quickly press and release the Bell button. To turn the bell off, press and release the Bell button again.
Loco-Sound Operating Instructions Activating Loco-Sound Features This manual contains the operating instructions for Proto-Sound 2.0 in conventional mode only. Instructions for accessing DCS command mode features accompany the DCS Remote Control System equipment. Timing Chart Press Horn Short & Firm ½ Sec. Pause Feature to Be Activated: Speed Control On/Off Lock into a Direction/Unlock Press ½ Sec.
Speed Control M.T.H. engines equipped with Proto-Sound 2.0 have speed control capabilities that allow the engine to maintain a constant speed up and down grades and around curves, much like an automobile cruise control. You can add or drop cars on the run, and the engine will maintain the speed you set. While the engine is programmed to start with the speed control feature activated, you can opt to turn it off.
not change direction (including going into neutral) until you repeat the 1 horn, 3 bells code to return the engine to its normal condition, even if the engine is kept without power for extended periods of time.
Maintenance Lubricating and Greasing Instructions The engine should be well oiled and greased in order to run properly. Regularly lubricate all axles and linkage components and pickup rollers to prevent squeaking. Use light household oil, such as that found in M.T.H.'s maintenance kit. Do not over oil. Use only a drop or two on each pivot point.
5. Repeat the procedure for the other motor and truck. 6. Reassemble the chassis and body, being careful that the wires are not caught between the body and chassis, as this can lead to a short that may damage the electronics beyond repair. 7. Before replacing body mount screws, test the unit on powered track to make sure all light housings are in place and functioning. Replace screws and door slider handles.
Lightbulb Replacement Instructions Interior Lights To replace the interior lights in the powered unit: 1. Follow the shell removal instructions found in the “Lubrication and Greasing” section of this booklet. 2. Pull bulb straight out to remove. Gently Pull Bulbs Away From Socket To Remove Figure 5 To replace the interior lights in the unpowered units: 1. Remove the four Phillips screws from the chassis (same as power unit), then lift the body away from the chassis.
Headlights To replace the headlights and other end-of-car lights in the powered unit: 1. Remove the shell as described in the “Lubrication and Greasing” section of this booklet. Gently Pull Bulbs Away From Socket To Remove 2. Pull out the bulb shown in Figure 8 to replace the Number/Destination Board bulb. 3. To replace the headlight bulbs, remove the harness witht the blue 2 pin connector shown in Figure 9. Figure 8 4.
Traction Tire Replacement Your subway set is equipped with two neoprene rubber traction tires on each powered truck block. While these tires are extremely durable, you may need to replace them at some point. First, remove the truck sides from the truck block. To do this, turn your engine upside down and remove the truckside mounting screws as seen in Figure 10. Screws to Remove Trucksides Once the truck sides have been removed: 1.
Troubleshooting Loco-Sound Problems Although Proto-Sound 2.0 has been designed and engineered for ease of use, you may have some questions during initial operation. The following table should answer most questions. If your problem cannot be resolved with this table, contact M.T.H. for assistance (telephone: 410-381-2580; fax: 410-423-0009; service@mth-railking.com, 7020 Columbia Gateway Drive, Columbia MD 21046-1532). Starting Up Remedy When I first turn the power on, the engine will not begin to run.
Volume Remedy The sounds seem distorted, especially Loco-Sound volume is set too high. Turn the volume control knob on the when the whistle or bell is activated. bottom of the chassis counterclockwise to reduce the volume.
Transformer Compatibility and Wiring Chart Proto-Sound 2.0 is designed to work with most standard AC transformers. The chart below lists the many compatible transformers. Note that many of the operational commands described in these instructions require a bell button, so if your transformer does not have its own bell button, you should consider adding one to get the full benefit of the system. In addition, the chart details how the terminals on these transformers should be attached to your layout.
Service & Warranty Information How to Get Service Under the Terms of the Limited One-Year Warranty For warranty repair, follow the instructions below to obtain warranty service. First, e-mail, write, call or fax an Authorized M.T.H. Service Center in your area or M.T.H. Electric Trains to obtain Repair Authorization. You can find the list of Authorized Service Centers on the M.T.H. website, www.mth-railking.com. Otherwise, contact M.T.H. (at e-mail: service@mth-railking.
AUTHORIZED SERVICE CENTER 7020 Columbia Gateway Dr. - Columbia, MD 21046 Information: 410-381-2580 Fax: 410-381-6122 www.mth-railking.com PARTICIPATING RETAILER LIST ALABAMA SOUTHERLAND STATION HUNTSVILLE 256-533-4720 railway@bellsouth.net ARIZONA ARIZONA TRAIN DEPOT MESA 480-833-9486 sales@arizonatraindepot.com www.arizonatraindepot.com/ CALIFORNIA DOLLHOUSES, TRAINS & MORE NOVATO 415-883-0388 kbecker@cmc.net TIN PLATE JUNCTION OAKLAND 510-444-4780 TOYTRAINS@email.msn.
MISSOURI SWITCH STAND SAINT LOUIS 314-781-4458 r41877@earthlink.com COUNTRY AND STUFF ANDOVER 973-786-7086 stuff@crystal.palace.net RIDGEFIELD HOBBY RIDGEFIELD 201-943-2636 MARK TWAIN HOBBY CENTER ST. CHARLES 636-946-2816 webmaster@hobby1.com www.hobby1.com COLUMBUS TRAIN STATION COLUMBUS 609-518-1800 NEW HAMPSHIRE TREASURED TOYS SALEM 603-898-7224 ttoys@treasured-toys.com www.treasured-toys.com NEW YORK AURORA RAILS & HOBBIES EAST AURORA 716-652-5718 rk82141@aol.
THE STATION NEW CUMBERLAND 717-774-7096 station@paonline.com BUSSINGER TRAINS AMBLER 215-628-2366 choochoos@icdc.com www.icdc.com/~btrains CHARLEROI SWEEPER CENTER CHARLEROI 724-483-3397 AMERICAN HOBBY CENTER ALIQUIPPA 724-378-3930 american@icubed.com CRANBERRY HOBBY DEPOT CRANBERRY TWP 724-776-3640 JAdams6113@aol.com TENNESSEE MODEL RAILROAD & HOBBY SHOP MEMPHIS 901-384-6500 mrhs99@earthlink.net www.modelrailroadandhobby.com WISCONSIN SOMMERFELD'S TRAINS BUTLER 262-783-7797 questions@sommerfelds.com www.
