Use and Care Manual

PRECAUTIONS
Do not apply to surfaces if moisture content is greater than 15%
as measured with an electronic moisture meter. Do not apply
materials in climates where freezing temperatures have existed
prior to application. Allow adequate time for surfaces to thaw.
Establish that air, surface, and material temperatures are above
40
°F (4.4°C) and at least 5°F above the dew point prior to paint-
ing. Do not apply at temperatures below 40°F or when temper-
atures are expected to drop below 4
0°F within 48 hours of ap-
plication. Do not apply if rain, snow, or lower temperatures are
expected within 48 hours. Do not apply if relative humidity is
greater than 90%.
Use material in a well-ventilated area. Protect the work of other
trades. Protect shrubbery and other plants with drop cloths.
Protect automobiles and all other areas not to be coated from
over-spray. Remove overspray from any windows, automobiles,
metal, etc. as soon as possible should it occur. To prevent per-
manent staining, clean spills or leaks in a timely manner.
Store materials in a well-protected area between 45° and 90°F.
Avoid freezing temperatures, direct sunlight, and moisture.
Keep away from heat sources.
All cracks (other than hairline) shall be pointed or caulked. All
voids and bee holes or other masonry surface defects shall be
repaired, allowing patching materials and sealers to cure prior to
application of materials. Repair wood surfaces using commer-
cially available wood patching compound.
Test Panel
Always apply material to a mock wall or test panel. Test wall or actu-
al surface area to determine acceptable color, surface porosity, appli-
cation rates and methods before starting general application.
LIMITED WARRANTY PROCEDURES/INFORMATION
The information contained herein is offered in good faith and is
believed to be accurate. To be eligible for a Rainguard Warranty
the following must occur:
1. A site visit must be conducted by an employee or agent of
Rainguard and a Field Inspection Report completed.
2. A Warranty Application must be fully completed by the
applicator.
3. Field Inspection Report, Warranty Application, and a copy
of the distributor’s invoice must be submitted to and ap-
proved by Rainguard.
4. This material is only warranted when applied in accordance with the
manufacturer’s guidelines and warranty procedures. Without adher-
ence to these specific guidelines, no expressed or implied warranty
of this product is given. Please contact Rainguard for additional infor-
mation.
Horizontal Concrete Surfaces
Apply two saturaon coats to damp concrete to assist the
curing and hardening process. Apply one saturaon coat to ex-
isng concrete surfaces to dustproof surfaces. Remove excess
standing or ponding materials with a roller. Cauon: PLUGGER
10 is not recommended for applicaon to surfaces subject to
wheeled trac.
Brick
Apply one saturaon coat with run-down and back roll material.
Apply second saturaon coat when the rst coat is dry.
Stucco/Plaster
May be applied to stucco or plaster during the curing process or
when fully cured. Apply one saturaon coat and back roll materi-
als. Apply second coat when the rst coat is dry.
Chalked Surfaces
Apply one coat to chalked surfaces. Allow material to dry
and check surface for chalking. Apply a second coat to surfaces as
needed to control remaining surface chalk.
Wood
Surfaces shall be clean and bare. Pre-treat knots with a small
amount of material. Apply a minimum of two saturaon coats to
wood surfaces. Apply second coat when the rst coat is dry.
Masonry and Concrete
All surfaces to be coated shall be structurally sound, clean, and
dry, free of laitance, accumulated dirt and grime, eorescence,
lime run, form oils and release agents, grease, mud, excess mor-
tar, and mold and mildew, etc. Remove loose and peeling paint,
excessive chalk, and other contaminants from surfaces. Dry
brushing is the preferred method for cleaning surfaces prior to
material applicaon. However, chemical, mechanical, abrasive,
or high-pressure water blasng may be used. Allow wet, cleaned
surfaces to dry for 2-3 days before applicaon of materials.
EFIS and Other Surfaces
Surfaces shall be structurally sound, clean, and dry. Clean EFIS
surfaces following manufacturer’s recommendaons.