Use and Care Manual

FOLLOW THESE SIMPLE STEPS
1. WATERPROOFER should be applied using low-pressure airless spray
equipment., or bug spray equipment.
2. Avoid atomizing material by using a spray tip size of .035 to .051.
Spray head should be held 8 to 12 inches from the surface so that
the flood coat runs down the wall approximately 6-12 inches below
the point of application.
3. Avoid application in windy weather.
4. Trigger gun off at the end of each pass to avoid using excessive ma-
terials. Stop all applications only at corners, joints, seams or edges.
5. Multiple coats may be applied.
TECHNICAL DATA
Material Type Silane/Siloxane
Active Content 100%
Volume Solids 40%
Color of Material Milky White
Odor Slight Ammonia Odor
V.O.C. <15 g/L V.O.C. Compliant
Flash Point Non-Flammable
pH Value Approximately 12.5
Viscosity 9.6 Seconds No. 4 Ford Cup
Weight Approximately 8.7 lbs./gal.
Surface Dry/Recoat Approx 1 Hour
Full Chemical Cure 5 to 7 days
TEST DATA
Wind Driven Rain ASTM E-514-86. 98.7% Leak Red
Water Pen Fed Spec SS-W-110C 75% Min Req
96.8% Leak Red Chloride Ion Intr
Salt Pounding NCHRP No. 244 Series IV - 95% Red.
244 Series II - 83% Red.
Water Abs CMU ASTM C140-75
98.6% Effective
Water Vapor Trans ASTM D-1653-71 100% Vapor Perm
Water Repellency ASTM C67-8798.6% Effective
Weathering ASTM G-53 3500 Hours - No Change
Surface Burning ASTM E84 Flame Spread 0, Smoke developed 0
LIMITED WARRANTY INFORMATION
Rainguard International warrants that if you are not completely satisfied
with this product, when applied according to the above specifications,
Rainguard will, at its option either replace the used material or refund
the purchase coast of the material. Said warranty is good for a period
of Ten (10) years from documented purchase date and the warranty is
not transferable. Rainguard will not be responsible for (1) labor or the
cost of removing product;, or (2) any incidental or consequential damag-
es, or (3) damages caused by acts of God or vandalism.
PRECAUTIONS & LIMITATIONS
All surfaces to be coated shall be clean of any dirt and grime,
efflorescence, lime run, form oils and release agents, grease, mud,
excess mortar and mold and mildew, etc. All cracks shall be
pointed or caulked. All voids, bee-holes, masonry surface defects
and openings such as conduits, pipes, drains, door frames, vents,
air conditioner openings, electrical openings, control joints or any
dissimilar materials shall be repaired using urethane or other ap-
proved patching.
Dilution - Concentrate ONLY
If product is Ready To Use - DO NOT DILUTE
ECO-POD™ - 1 POD per 1 gallon of water
ECO-Quart™ 2 Gallon - Mix Quart with 2 gallons of water
ECO-Quart™ 5 Gallon - Mix Quart with 5 gallons of water
Do not apply to surfaces if moisture content is greater than 25%
as measured with an electronic moisture meter. Do not apply
materials in climates where freezing temperatures have existed
prior to application, allow adequate time for surfaces to thaw.
Establish that air, surface and material temperatures are above
40°F (4.4°C) and at least 5°F above the dew point prior to
painting. Do not apply at temperatures below 40°F or when
temperatures are expected to drop below 40°F within 48 hours
of application. Do not apply if rain, snow or lower temperatures
are expected within 48 hours. Do not apply if relative humidity is
greater than 90%.
Use material in a well ventilated area. Protect shrubbery and oth-
er plants with drop cloths. Protect automobiles and all other
areas not to be coated from over-spray. Remove overspray from
any windows, automobiles, metal etc. as soon as possible should
it occur. To prevent permanent staining, clean spills or leaks in a
timely manner.
Store materials in a well-protected area between 45° and 90°F.
Avoid freezing temperatures, direct sunlight and moisture. Keep
away from heat sources.
TEST PANEL
Always apply material to a mock wall or test panel, test wall or
actual surface area to determine acceptable color, surface po-
rosity, application rates and methods before starting general
application.