Manual

ManualsBrandsRainbow Electronics ManualsStorageAT29BV010A

1

2

3

4

5

6

7

8

9

1

Features

• Single Supply Voltage, Range 2.7V to 3.6V

• Single Supply for Read and Write

• Software Protected Programming

• Fast Read Access Time - 120 ns

• Low Power Dissipation

– 15mAActiveCurrent

– 40 µA CMOS Standby Current

• Sector Program Operation

– Single Cycle Reprogram (Erase and Program)

– 1024 Sectors (128 Bytes/Sector)

– Internal Address and Data Latches for 128 Bytes

• Two 8K Bytes Boot Blocks with Lockout

• Fast Sector Program Cycle Time - 20 ms Max.

• Internal Program Control and Timer

• DATA Polling for End of Program Detection

• Typical Endurance > 10,000 Cycles

• CMOS and TTL Compatible Inputs and Outputs

• Commercial and Industrial Temperature Ranges

Description

The AT29BV010A is a 2.7-volt only in-system Flash Programmable and Erasable

Read Only Memory (Flash). Its 1 megabit of memory is organized as 131,072

words by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS EEPROM

technology, the device offers access times to 120 ns, and a low 54 mW power

dissipation. When the device is deselected, the CMOS standby current is less than 40

µA. The device endurance is such that any sector can typically be written to in excess

1-megabit

(128K x 8)

Single 2.7-volt

Battery-Voltage

™

Flash Memory

AT29BV010A

Rev. 0519D–FLASH–05/02

PLCC

Top View

Pin Configurations

Pin Name Function

A0 - A16 Addresses

CE

Chip Enable

OE

Output Enable

WE

Write Enable

I/O0 - I/O7 Data Inputs/Outputs

NC No Connect

5

6

7

8

9

10

11

12

13

29

28

27

26

25

24

23

22

21

A7

A6

A5

A4

A3

A2

A1

A0

I/O0

A14

A13

A8

A9

A11

OE

A10

CE

I/O7

4

3

2

1

32

31

30

14

15

16

17

18

19

20

I/O1

I/O2

GND

I/O3

I/O4

I/O5

I/O6

A12

A15

A16

NC

VCC

WE

NC

TSOP Top View

Type 1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

32

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

A11

A9

A8

A13

A14

NC

WE

VCC

NC

A16

A15

A12

A7

A6

A5

A4

OE

A10

CE

I/O7

I/O6

I/O5

I/O4

I/O3

GND

I/O2

I/O1

I/O0

A0

A1

A2

A3

Summary of content (15 pages)

PAGE 1
Features • • • • • • • • • • • • • Single Supply Voltage, Range 2.7V to 3.6V Single Supply for Read and Write Software Protected Programming Fast Read Access Time - 120 ns Low Power Dissipation – 15 mA Active Current – 40 µA CMOS Standby Current Sector Program Operation – Single Cycle Reprogram (Erase and Program) – 1024 Sectors (128 Bytes/Sector) – Internal Address and Data Latches for 128 Bytes Two 8K Bytes Boot Blocks with Lockout Fast Sector Program Cycle Time - 20 ms Max.
PAGE 2
of 10,000 times. The programming algorithm is compatible with other devices in Atmel’s Low Voltage Flash family of products. To allow for simple in-system reprogrammability, the AT29BV010A does not require high input voltages for programming. The device can be operated with a single 2.7V to 3.6V supply. Reading data out of the device is similar to reading from an EPROM.
PAGE 3
AT29BV010A Any attempt to write to the device without the 3-byte command sequence will start the internal write timers. No data will be written to the device; however, for the duration of tWC, a read operation will effectively be a polling operation. After the software data protection’s 3-byte command code is given, a byte load is performed by applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high.
PAGE 4
and valid data will be read. Examining the toggle bit may begin at any time during a program cycle. OPTIONAL CHIP ERASE MODES: The entire device may be erased by using a 6-byte software code. Please see Software Chip Erase application note for details. BOOT BLOCK PROGRAMMING LOCKOUT: The AT29BV010A has two designated memory blocks that have a programming lockout feature. This feature prevents programming of data in the designated block once the feature has been enabled.
PAGE 5
AT29BV010A DC and AC Operating Range Note: AT29BV010A-15 AT29BV010A-20 AT29BV010A-25 AT29BV010A-30 0°C - 70°C 0°C - 70°C 0°C - 70°C 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C -40°C - 85°C -40°C - 85°C 2.7V to 3.6V 2.7V to 3.6V 2.7V to 3.6V 2.7V to 3.6V Com. Operating Temperature (Case) VCC Power Supply AT29BV010A-12 Ind. (1) 2.7V to 3.6V 1.
PAGE 6
AC Read Characteristics AT29BV010A-12 Symbol Parameter tACC Min AT29BV010A-15 Max Min Max AT29BV010A-20 Min Max AT29BV010A-25 Min Max AT29BV010A-30 Min Max Units Address to Output Delay 120 150 200 250 300 ns (1) CE to Output Delay 120 150 200 250 300 ns tOE(2) OE to Output Delay 0 50 0 100 0 100 0 120 0 150 ns tDF(3)(4) CE or OE to Output Float 0 30 0 50 0 50 0 60 0 75 ns tOH Output Hold from OE, CE or Address, whichever occurred first 0 tCE Note:
PAGE 7
AT29BV010A Input Test Waveforms and Measurement Level tR, t F < 5 ns Output Test Load Pin Capacitance f = 1 MHz, T = 25°C(1) Symbol Typ Max Units Conditions CIN 4 6 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. These parameters are characterized and not 100% tested.
PAGE 8
AC Byte Load Characteristics Symbol Parameter Min Max Units tAS, tOES Address, OE Set-up Time 10 ns tAH Address Hold Time 100 ns tCS Chip Select Set-up Time 0 ns tCH Chip Select Hold Time 0 ns tWP Write Pulse Width (WE or CE) 200 ns tDS Data Set-up Time 100 ns tDH, tOEH Data, OE Hold Time 10 ns tWPH Write Pulse Width High 200 ns AC Byte Load Waveforms(1)(2) WE Controlled CE Controlled 8 AT29BV010A 0519D–FLASH–05/02
PAGE 9
AT29BV010A Program Cycle Characteristics Symbol Parameter Min Max Units tWC Write Cycle Time 20 ms tAS Address Set-up Time 10 ns tAH Address Hold Time 100 ns tDS Data Set-up Time 100 ns tDH Data Hold Time 10 ns tWP Write Pulse Width 200 ns tBLC Byte Load Cycle Time tWPH Write Pulse Width High 150 200 µs ns Software Protected Program Waveform Notes: 1. OE must be high when WE and CE are both low. 2.
PAGE 10
Data Polling Characteristics(1)(2) Symbol Parameter tDH Data Hold Time tOEH OE Hold Time Min Max Units 10 ns 10 ns (2) tOE OE to Output Delay tWR Write Recovery Time Notes: Typ ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in AC Read Characteristics.
PAGE 11
AT29BV010A Software Product Identification Entry(1) LOAD DATA AA TO ADDRESS 5555 Boot Block Lockout Feature Enable Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 90 TO ADDRESS 5555 PAUSE 20 mS LOAD DATA 80 TO ADDRESS 5555 ENTER PRODUCT IDENTIFICATION MODE(2)(3) LOAD DATA AA TO ADDRESS 5555 Software Product Identification Exit(1) LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA AA TO ADDRESS 5555 LOAD DATA 40 TO ADDRESS 5555 LOAD DATA 55 TO AD
PAGE 12
Ordering Information ICC (mA) tACC (ns) Active Standby 120 15 Ordering Code Package 0.04 AT29BV010A-12JC AT29BV010A-12TC 32J 32T Commercial (0° to 70°C) 15 0.05 AT29BV010A-12JI AT29BV010A-12TI 32J 32T Industrial (-40° to 85°C) 15 0.04 AT29BV010A-15JC AT29BV010A-15TC 32J 32T Commercial (0° to 70°C) 15 0.05 AT29BV010A-15JI AT29BV010A-15TI 32J 32T Industrial (-40° to 85°C) 200 15 0.04 AT29BV010A-20JC AT29BV010A-20TC 32J 32T Commercial (0° to 70°C) 250 15 0.
PAGE 13
AT29BV010A Packaging Information 32J – PLCC 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER 1.14(0.045) X 45˚ 0.318(0.0125) 0.191(0.0075) E1 E2 B1 E B e A2 D1 A1 D A 0.51(0.020)MAX 45˚ MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) D2 Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side.
PAGE 14
32T – TSOP PIN 1 0º ~ 8º c Pin 1 Identifier D1 D L b e L1 A2 E A GAGE PLANE SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) A1 MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 19.80 20.00 20.20 D1 18.30 18.40 18.50 Note 2 E 7.90 8.00 8.10 Note 2 L 0.50 0.60 0.70 SYMBOL Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion on E is 0.
PAGE 15
Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg.