ENGLISH RAIS - manual for Q-BIC & Q-BIC insert USER MANUAL RAIS Q-BIC & RAIS Q-BIC INSERT 1
We cannot be held responsible for any misprints.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert RAIS Q-BIC RAIS Q-BIC insert Date: December 2009 Modified: D INTRODUCTION ................................................................................................................................... 4 WARRANTY.......................................................................................................................................... 4 SPECIFICATIONS............................................................................................
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Introduction Thank you for purchasing a RAIS wood burning stove. These appliances have been approved by HETAS Ltd as intermittent operating appliances for burning wood logs only. A RAIS wood burning stove is more than just a heat source: it also shows that you care about design and quality in your home. To make the most of your wood burning stove it is important that you read the manual thoroughly, before installing and using it.
2-6 ca. 80 426-418-850 288-288-500 1,6 -12 140 6,3 253 2-6 ca. 80 404-404-1270 288-288-500 1,6 -12 153 6,3 253 2-6 ca. 80 404-404-1060 288-288-500 1,6 -12 143 6,3 253 Min./Max. output(kW): Stove’s width/depth/height (mm) Combustion chamber’s width/depth/height (mm) Recommended amount of wood when fuelling (kg): (Distributed on 2-3 logs of wood of approx. 25 cm) Min.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Convection RAIS stoves are convection stoves. This means that the stove’s back and side panels are not over-heated. Convection means that there is a circulation of air, which ensures that the heat is distributed more evenly throughout the entire room. The cold air is sucked in at the base of the stove up through the convection channel, which runs along the stove’s combustion chamber.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Installation instructions The following pages give instructions for the safe and proper installation of this heating appliance in the UK. These instructions cover the basic principles of installation, although detail may need slight modification to suit particular local site conditions.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Chimney The chimney is the driving force which makes the stove function. In order for the stove to perform satisfactorily the chimney height must be sufficient to ensure the correct draught of 14 to 18 Pa so as to clear the products of combustion and prevent problems of smoke emanating into the room when firing. NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of the stove to the top of the chimney should be satisfactory.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert If it is found that there is excessive draught in the chimney then either an adjustable flue damper or alternatively a draught stabiliser should be fitted. The adjustable flue damper should not close off the flue entirely but should in its closed position leave a minimum continuous opening free area of at least 20 % of the total cross sectional area of the flue or fluepipe. Adequate provision e.g.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Installation It is prohibited to carry out unauthorised alterations to the stove. There must be plenty of fresh air in the room where the stove is being installed, in order to ensure proper combustion. Note that any mechanical exhaust ventilation - e.g. an extraction hood - may reduce the air supply. Any air grates must be placed in such a manner, that the air supply is not blocked.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert 11
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Installation instructions - Q-BIC insert First loosen the screw in upper right corner and the screw in lower left corner (both door side) - do not onscrew entirely - now it’s possible to remove the insert from the cassette. Prefaration of cassette Disassemble the two screws keeping the stiffening rib in position. By a panelled wall: Assemble the cassette, the upper covering plate and the stiffening rib with the two screws.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Assembly the topplate with the following self-drilling screws. By a brick wall: The outermost part of the upper covering is broken off before it is assembled with the two screws. The top plate is not used NB!! A 30° bend must always be used for a brick wall. The legs are fixed onto the box and this is then placed in the desired position. For panelled wall, all 3 legs are used and for brick wall, only the back leg is used.
ENGLISH Fitting hole for brick wall RAIS - manual for Q-BIC & Q-BIC insert Fitting holes for angle brace for panelled wall. ATTENTION!! Important that the cassette is posotion in 90° angel and levelled both horizontal an vertical.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Assembly the stove in cassette Lift the stove up onto the base plate and place it as shown in the picture on the left. NB!! Basic settings on the adjusting bolts are approx. 32.5 mm (between the bottom of the stove's base and the base plate on the internal box). Please note that there may be a need for added adjustment in order for the stove to stand at a level position.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Push the insert until the front is in level with the wall. Afterwards push the insert from the other side until it is in level with the other wall. The screws - in upper right corner and lover left corner - you started loosen (page 8), is fastened.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert 17
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Q-BIC insert Brick and panelled wall Mounting distance for panelled wall - combustible material (insulation ability such as Aqua panel (coefficient of thermal conductivity 0.36 W/mk) or better) NB!! OBS!!! Hullerne i bunden må 197 Do covertil. the ikkenot dækkes holes! Min. 500 Min. 200 60 1 185 524 417 516 Min. 734 516 417 Min. 300 Min. 743 H-H H 524 858 H Min. 200 100 Total areal min. area 250 cm² cm Min.
A-A 417 858 417 ~ Min. 643 425 Min. 300 A Min. 617 ~ Min. 617 ~ Min. 426 A Min. 434 Min. 643 ~ 425 15 Total min. area Min. areal 250 cm cm² ialt 250 10 Total min. area Min. areal 500 cm cm² ialt 500 15 232 300 Recommended min.min. distance Anbefalet afstand Distance to loft ceiling Afstand til min. min.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Installation distance in case of non-combustible wall We recommend a minimum distance to non-combustible material of 50 mm (F) for cleaning considerations. It should always be possible to access the accessdoor. Using not insulated smoke pipe, the minimum distance to combustible wall must be 225 mm from smoke pipe.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Normal set-up (right-angle) secure base A. Distance to furniture 750 mm Distance to flammable materials: B. - in front (floor) 300 mm C. - to the side (floor) 150 mm D. - to the rear (floor) 350 mm E.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Corner set-up 45° fixed socket A. Distance to furniture 750 mm Distance to flammable materials: B. - in front (floor) C. - to the side (floor) D. - to the rear (wall) E. - to the side of the wall 300 mm 150 mm 200 mm 500 mm 360° swivel base A. Distance to furniture Distance to flammable materials: B.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert For the Installer Finally before firing the stove for the first time a check should be made to ensure that the assembly and stove installation has been satisfactory and that there are no leaks in any seals in the appliance and appliance connections to the chimney. Ensure that the appliance and chimney flue are functioning correctly before finally handing over to the user.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Operating instructions Please note that HETAS Ltd Appliance Approval only covers the use of dry seasoned wood logs on this appliance. HETAS Ltd Approval does not cover the use of other fuels either alone or mixed with the wood logs, nor does it cover instructions for the use of other fuels. Fuel The stove is designed and approved in accordance with EN 13240 and NS 3058 for stoking split, dried firewood.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Drying and storage Drying wood takes time: proper air drying takes approx. 2 years. Here are some tips: Store the wood sawn, split and stacked in an airy, sunny place, which is protected against rain (the south side of the house is particularly suitable). Store the firewood stacks at a hand’s breadth apart, as this ensures that the air flowing through takes the moisture with it.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Using the wood burning stove Adjustment of the air damper. The damper has 3 settings. RAIS Q-BIC Position 1 The air damper is closed, which means no air supply. Position 2 Push the handle to the left, to wher the marking is. This position gives full secondary air. During normal stoking the lever is set between position 1 and 2. When the flames are clear and yellow, the damper is set correctly, i.e. resulting in a slow/optimal burning.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert RAIS Q-BIC insert Position 1 The air damper is closed, which means no air supply. Position 2 Push the handle to the left, to wher the marking is. This position gives full secondary air. During normal stoking the lever is set between position 1 and 2. When the flames are clear and yellow, the damper is set correctly, i.e. resulting in a slow/optimal burning. Position 3 Press the handle in, and push it to the left until stop.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert First usage A careful start pays off. Start with a small fire, so that the wood burning stove can get accustomed to the high temperature. This gives the best start and any damage is avoided. Be aware that a strange but harmless odour and smoke concoction may emanate from the surface of the stove, the first time you fire up. This is because the paint and materials need to harden.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Lighting and fuelling To light the stove, use alcohol briquettes or similar, as well as approx. 2 kg of firewood, split into kindling sticks. Set the air damper to the fully open position. TIPS before firing up: Open a door or window close to the wood burning stove.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert When the flames are clear - after approx. 5-10 min. - close the door. Damper - see adjustment of air damper. After approx. 10-20 min. - when you have a good bed of glowing embers - add 2-3 pieces of wood. Leave the door ajar until the fire has caught on properly - close the door. Damper - see adjustment of air damper. After approx. 5 min. - or when the flames are clear and stable - close the damper gradually.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Cleaning and care The wood burning stove and the chimney must be serviced by a chimney sweep twice a year. During cleaning and care, the stove must be cold. If the glass is sooty: - Moisten a piece of paper or newspaper, dip it in the ash, and rub the sooty glass with it. - Now rub with a piece of paper and the glass will become clean. - As an alternative you can use glass polish, which you can buy from you RAIS distributor.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Cleaning of the flue ways The fixing clips are pushed up and removed from the skamol on the side. The fixing clips is placed in the top right corner of the firebox. The picture on the left is a detailed view of the top right corner of the firebox (A close-up of the area is marked by a circle in the next picture). The baffle is pulled towards the front and is tipped down towards the firebox. Note that the skamol on the sides are now loose.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Interruption of operation Smoke spillage around door: Could be due to too low draught in the chimney <12Pa - Check whether the flue or chimney is blocked - check whether the extraction hood is switched on; if it is, switch it off and open a window/door in the proximity of the stove for a short while. Soot on glass: Could be because the firewood is too wet.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Accessories and spare parts If spare parts other than those recommended by RAIS are used, the warranty is voided. All replaceable parts can be bought as spare parts from your RAIS distributor. See the following spare parts diagrams for the individual products. Spare parts diagram - RAIS Q-BIC 106 Pos. Number Item no.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert 35
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Spare parts diagram - RAIS Q-BIC 127 Pos. Number Item no.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert 37
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert Spare parts diagram - RAIS Q-BIC insert Pos. Number 1 1 2 1 3 1 Item no.
ENGLISH RAIS - manual for Q-BIC & Q-BIC insert 5 7 8 6 2 4 3 9 10 1 39
RAIS A/S Industrivej 20 DK-9900 Frederikshavn www.rais.