Owner's manual

ManualsBrandsRally Armor ManualsFor bicycles11-14 Subaru WRX & STI Sedan

IMF19Version1.3ReleaseDate10.22.20101



ToprotectyourRallyArmormudflapset,caremustbetakenduringparkingandreversing.Checkwheelclearanceafterinstallation,

especiallyonvehiclesoutfittedwithnon‐OEMoffsetwheelsandsuspensions.Adjusttoaccommodateaccordinglyinthese

scenarios.RallyArmorisnotresponsiblefordamageorlossofinstalledflaps.



Eachmudflapsetcontains4flapsforallfourtiresofthevehicle.

Recommendedtools:Offsetorratchetingscrewdriver,stubbyPhillipsscrewdriver,small&longflatheadscrewdriver,7/16”wrench.



YOUR2011STI&WRXSEDANHARDWARECONSISTSOF: GUIDETOINSERTSPROVIDED: HOWTOREMOVESTOCKFASTENERS:



Quantity HardwareItem ItemID

6 PolygonEdgeClips PolCl

12 SmallWashers SmWash

8 LockNuts SSLnut

4 ShortScrews 1SS

4 FlatheadScrews 15FHSS

2 Inserts Ins

2 Inserts‐withplasticscrew ScwIns

2 FrontMountingBrackets HMF19‐F‐BR

2 RearMountingBrackets HMF19‐R‐BR



CautionaryTip:Thehardwareisstrongandself

threadingbutover‐tighteningtheclipsisnotadvised.



InstallationTip:Toeaseinstallationandavoiddamage

toexistingOEMclipsduringremoval,awelllit,climate

controlledinstallationenvironmentisrecommended.



Totheinstaller:Pleasereturntheseinstructionstothecustomerafterinstallation.Alwaystest

andcheckwheelclearancebeforereturningvehicle.

Tothecustomer:Retaintheseinstructions

afterinstallation.Theymaybenecessaryfor

installingotheroptionalpartsorremovalofthisaccessory.

Summary of content (6 pages)

PAGE 1
To protect your Rally Armor mud flap set, care must be taken during parking and reversing. Check wheel clearance after installation, especially on vehicles outfitted with non‐OEM offset wheels and suspensions. Adjust to accommodate accordingly in these scenarios. Rally Armor is not responsible for damage or loss of installed flaps. Each mud flap set contains 4 flaps for all four tires of the vehicle.
PAGE 2
Front Mud Flap Installation Begin by parking the vehicle on an even surface. Turn the steering wheel towards the side you are working on to gain access to the wheel well area. • (Figure A) Open car door to avoid contact with side skirt. Remove first two push clips under the side skirt. • (Figure B) Carefully unclip front portion of side skirt by pulling the outer edge away just enough to release two horizontal retainer clips. • (Figure C) Remove the plastic fender cover in increments.
PAGE 3
• (Figure G) Loosely fit fender cover back on to the vehicle and adjust mounting bracket clearances to cover and side skirt by slightly tightening or loosening mounting screws. Important: Lower mounting point of bracket is slotted. Align the lower innermost portion of the bracket by adjusting it inwards, to its fullest extent into the vehicle, prior to final bolting. • (Figure H) Replace cover and side skirt when adjustment is complete.
PAGE 4
• (Figure M) Example of bracket incorrectly positioned. Lower portion of bracket should not be parallel to cover. • (Figure N) Example of bracket correctly positioned. Mounting hole will be visible through the lower slot of bracket. • (Figure O) Note proper tabbed end placement on cover. The components will align during re‐installation into bumper cover. • (Figure P) Position the bumper piece assembly with bracket back on to vehicle. Position the bracket tabs over bumper cover.
PAGE 5
• (Figure S) Place the mud flap against the corresponding mounting points on the bracket. Base of threaded bolt must be inside of mounting point of mud flap. Pass small washers (SmWash) over the flap on to the threaded bolts. Install lock nuts (SSLnut) on the two threaded mounting points. Thread a short screw (1SS) with small washer through the flap into the mounted clip (PolCl). Do not fully tighten as you will be aligning the flap.
PAGE 6
Check wheel clearance after installation, especially on vehicles outfitted with non‐OEM offset wheels and suspensions. Adjust to accommodate accordingly in these scenarios. Rally Armor is not responsible for damage or loss of installed flaps. All content included on these instructions is the copyright of Rally Armor® LLC IMF19 Version 1.3 Release Date 10.22.