Instructions / Assembly

ADDITIONAL ITEMS: 3" Painter’s tape •
Drop cloth • Latex gloves • Paint tray
Ralph Lauren
METALLIC Paint
See Step One
for space
estimations.
Ralph Lauren
Specialty Finish
9" Sponge Roller
Cover with Small
Sea Sponge
Quality 9"
Roller Frame
with
3
/
8
" Nap
Roller Cover
METALLIC
HOW-TO GUIDE
WHAT YOU WILL NEED:
Presenting a sleek, luminous
nish that lends a shimmering
richness to classic colors and
introduces timeless luxury to
walls, trim and architectural
elements throughout the home
• Prior to use, the Sponge Roller
Cover should be rinsed thoroughly
with warm water, squeezed to remove
excess water and then allowed to dry
overnight.
• Measure your room to estimate how
much METALLIC you’ll need.
One gallon of METALLIC covers
approximately 200 square feet
with two coats. A typical 12’ X 12’
room with an 8’ ceiling requires
about two gallons. It will
take two coats to achieve the look
of METALLIC.
•
Always start with clean, dry walls
that have been primed with a latex
primer. METALLIC is not recommended
for ceilings or textured walls.
•
Tape off all areas to be painted with
3" painter’s tape, including across the
ceiling and any adjacent walls.
HELPFUL HINT For a consistent
appearance throughout the
room, one person should apply
METALLIC to all walls.
•
Condition the quality 9" roller with
3
/
8
" nap roller cover by
rolling it through the paint 20 to 30 times.
•
Starting at the top corner and working in an 18” x 18”
section, apply METALLIC in a random downward V-pattern until
the paint is spread uniformly, getting as close to the edge
of the wall as possible. Then do a final downward sweep in
various angles over the section. Use the small sea sponge to
coat any areas around the edges that you could not cover with
the roller.
•
Reload the roller and start another 18” x 18” section,
blending into the first area. Spread the paint uniformly as you
go. Continue applying in 18” x 18” sections until the wall is
covered.
•
Allow METALLIC to dry for at least two hours before proceed-
ing to Step Three.
•
For light colors requiring a second basecoat: Allow the first
coat to dry for at least two hours. Then, starting in the top
opposite corner of the wall, apply a second coat as described
above.
HELPFUL HINT Don’t be alarmed if you see random
roller marks and heavy overlaps with non-uniform
coverage, especially in lighter colors. This is the correct
appearance and helps create the finished effect.
STEP ONE: PREP STEP TWO: ROLL
•
Condition the Ralph Lauren Specialty Finish 9" Sponge Roller
by rolling it through the paint about 10 times. Don’t worry about
completely covering the roller’s deep grooves or crevices.
•
Starting in the top opposite corner from your final basecoat,
and working in a 12” x 12” section, apply METALLIC in a
random downward V-pattern until the paint is spread to an even
consistency. Then do a finaldownward sweep in various angles
over the section. Use the small sea sponge to coat any areas
around the edges that you could not cover with the roller.
•
Reload the roller and start another 12” x 12” section,
blending into the first area. Continue applying in 12” x 12”
sections until the wall is covered.
•
Gently remove the tape and allow to dry.
HELPFUL HINTS For future maintenance, a small artist’s
brush can touch up minor damaged zones. Due to the
directional nature of the finish, large marred areas
require the entire wall to be recoated.
METALLIC can be painted over without sanding.
Apply a coat or two of primer followed by your new
Ralph Lauren Paint or Ralph Lauren Specialty Finish.
12"
STEP THREE: SECOND COAT
FOR HOW-TO VIDEOS, GO TO HOMEDEPOT.COM/RALPHLAURENPAINT
18”
This application results in a hammered metal appearance.
To achieve a smooth metallic appearance, consult a paint
professional for the use of an HVLP sprayer.