2011 RAM TR U C K RAM TRUCK 2011 OWNER’S MANUAL Chrysler Group LLC 11D241-126-AB Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 NOTE: It is illegal to remove or alter the VIN. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through VEHICLE MODIFICATIONS/ALTERATIONS the windshield. This number also appears on the AutoWARNING! mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ General Information . . . . . . . . . . . . . . . . . . . 18 ▫ Wireless Ignition Node (WIN) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 18 ▫ Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ Removing Key FOB From Ignition . . . . . . . . . 14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 24 ▫ Transmitter Battery Replacement . . . . . . . . . . 24 ▫ General Information . . . . . . . . . . . . . . . . . . . 25 䡵 Remote Starting System — If Equipped . . . . . . . 26 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 26 䡵 Door Locks . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Enhanced Seat Belt Use Reminder System (BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . 51 ▫ Seat Belts And Pregnant Women . . . . . . . . . . 52 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 52 ▫ Supplemental Restraint System (SRS) – Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 ▫ Airbag System Components . . . . . . . . . . . . . . 54 ▫ Advanced Front Airbag Features . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Key Fob with Remote Keyless Entry (RKE) — If Equipped Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Standard Blade Ignition Key — If Equipped Your vehicle may use a standard blade key ignition system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK (if equipped with an automatic transmission). Turn the Key Fob to the OFF then pull the key out with your other hand. position and then remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid Key Fob to try to start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 All of the Key Fobs provided with your new vehicle have Duplication of Key Fobs may be performed at an authobeen programmed to the vehicle electronics. rized dealer, this procedure consists of programming a blank Key Fob to the vehicle electronics. A blank Key Fob Replacement Keys is one that has never been programmed.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security Light will flash. Use of the Sentry Key威 will General Information The Sentry Key威 system complies with FCC rules Part 15 disable the alarm. and with RSS-210 of Industry Canada. Operation is Rearming Of The System subject to the following conditions: The Vehicle Security Alarm will rearm itself after the 15 additional minutes of headlights and Vehicle Security • This device may not cause harmful interference.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: If the Vehicle Security Light stays on continu- Vehicle Security Alarm will arm regardless of whether ously during vehicle operation, have the system checked you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, by an authorized dealer. disarm the Vehicle Security Alarm. To Disarm The System Use the RKE transmitter to unlock the door.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE at speeds 5 mph (8 km/h) and above disables the system NOTE: • The front courtesy overhead console and door cour- from responding to all RKE transmitter buttons for all tesy lights do not turn off if the dimmer control is in RKE transmitters. the “Dome ON” position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 setup for driver door first, otherwise this will unlock all doors), or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lamps With Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Sound Horn With Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 3.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm • You may need to be less than 35 ft (11 m) from the To turn the Panic Alarm feature ON or OFF, press and vehicle when using the RKE transmitter to turn off the hold the PANIC button on the RKE transmitter for at Panic Alarm due to the radio frequency noises emitted least one second and release. When the Panic Alarm is on, by the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 1. With the RKE transmitter buttons facing down, use a • This device must accept any interference received, flat blade screwdriver to pry the two halves of the RKE including interference that may cause undesired transmitter apart. Make sure not to damage the seal operation. during removal. NOTE: Changes or modifications not expressly ap2. Remove and replace the battery.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). NOTE: The vehicle must be equipped with an automatic transmission to be equipped with Remote Start.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prematurely: • Remote Start Aborted - Door Ajar • Remote Start Aborted - Hood Ajar • Remote Start Aborted - Fuel Low will chirp twice (if programmed). Once the vehicle has started, the engine will run for 15 minutes.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE message “Turn To On” will flash in the EVIC until you NOTE: To avoid unintentional shut downs, the system turn the ignition switch to the ON/RUN position. will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Remote Start Comfort Systems — If Equipped Start request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 DOOR LOCKS Manual Door Locks Front and rear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE power locks will not operate. This prevents you from Power Door Locks — If Equipped A power door LOCK switch is on each front door trim accidentally locking your Key Fob in the vehicle. Removpanel. Use this switch to lock or unlock the doors. ing the Key Fob or closing the door will allow the locks to operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 6. The doors were not previously locked using the power 2. Within 15 seconds, cycle the ignition switch between door lock switch or Remote Keyless Entry (RKE) LOCK and ON/RUN and then back to LOCK four times ending up in the LOCK position (do not start the engine). transmitter 3. Within 30 seconds, press the power door LOCK switch Automatic Door Locks Programming — If to lock the doors. Equipped The Automatic Door Locks feature can be enabled or 4.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Doors — If Equipped This feature unlocks all of the doors of the vehicle when either front door is opened. This will occur only after the vehicle has been shifted into the PARK position after the vehicle has been driven (shifted out of PARK and all doors closed). 2. Fasten your seat belt. (Fastening the seat belt will cancel any chimes that may be confusing during this programming procedure.) 3. Insert the Key Fob into the ignition. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Child-Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the Child-Protection Door Lock system. engage and disengage the Child-Protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. WINDOWS Power Windows – If Equipped NOTE: • After setting the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab威, Mega Cab威 and Crew Cab models. The windows will operate when the ignition switch is turned to the ON/RUN or ACC position, and for up to 10 minutes after the ignition is turned OFF or until a front door is opened. WARNING! Never leave children alone in a vehicle.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press to the first detent conditions may trigger the auto reverse function unexpectedly during auto closure. If this happens, pull the and release it when you want the window to stop. switch lightly to the first detent and hold to close the Auto-Up Feature With Anti-Pinch Protection window manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window LOCKOUT Switch — 4–Door Models The window LOCKOUT switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCK button into the latched or down position.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE normal occurrence and can be minimized. If the rear • An energy-absorbing steering column and steering windows are open and buffeting occurs, open the front wheel and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause an accident that includes you. This can happen far away from home or on your own street. Please pay close attention to the information in this section.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accident the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out. WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of an accident best. • Two people should never be belted into a single seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 plate and pull out the belt. Slide the latch plate up the 3. When the belt is long enough to fit, insert the latch webbing as far as necessary to allow the belt to go around plate into the buckle until you hear a “click.” your lap.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in an accident. WARNING! • A lap belt worn too high can increase the risk of internal injury in an accident. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt will not protect you properly. In a collision, it could even cut into you.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Regular Cab Front Center Three Point Belt The belt will automatically retract to its stowed position. 1. The front center seat belt on the Regular Cab may be If necessary, slide the latch plate down the webbing to disconnected to open up utilization of the storage areas allow the belt to retract fully. behind the front seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Detaching Buckle With Seat Belt Tongue 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, refer “Lap/Shoulder Belt Operating Instructions”.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 located on the upper belt guide to release the anchorage, Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ and then move it up or down to the position that fits you best. shoulder belt. 2 1. Position the latch plate as close as possible to the anchor point. 2.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Center Lap Belts The center seating position for the Quad Cab威, Mega Cab威 and Crew Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a ⬙click.⬙ To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly “Automatic Locking Retractor (ALR)” feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in accidents.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor (ALR) Mode – If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. When To Use The Automatic Locking Mode Use the Automatic Locking Mode anytime a child safety seat is installed in a seating position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 accident. These devices may improve the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. 60 seconds of vehicle speed over 5 mph (8 km/h).
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With all doors closed and the ignition switch in any NOTE: Although BeltAlert威 has been deactivated, the position except ON/RUN or START, buckle the driver’s Seat Belt Reminder Light will continue to illuminate while the driver’s seat belt remains unbuckled or seat belt. unretracted. 2. Turn the ignition switch to the ON/RUN position and Seat Belts And Pregnant Women wait for the Seat Belt Reminder Light to turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 extender should be used only if the existing belt is not instrument panel, above the glove compartment. The long enough. When it is not required, remove the ex- words SRS AIRBAG are embossed on the airbag covers. tender and store it. WARNING! Using a seat belt extender when not needed can increase the risk of injury in an accident.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags have a multistage inflator NOTE: design. This allows the airbag to have different rates of • Airbag covers may not be obvious in the interior trim, but they will open during airbag deployment. inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front • After any accident, the vehicle should be taken to an authorized dealer immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • Supplemental Side Airbag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for sideimpact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! WARNING! (Continued) • If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the SABIC is located should remain free from any obstructions.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the ride properly buckled up in the rear seat. Never allow risk of harm from a deploying airbag: children to slide the shoulder belt behind them or under their arm. Children 12 years old and under should always ride buckled up in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Do not lean against the door or window. If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space between you and the door. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Based on the impact sensor’s signals, a central electronic ORC deploys the Advanced Front Airbags, SABIC airbags — if equipped, and front seat belt pretensioners — if equipped, as required, depending on the severity and type of impact. Advanced Front Airbags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. The side airbags will not deploy in all side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 position, in the ACC position, or not in the ignition, the airbag system is not on and the airbags will not inflate. The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Airbag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition is first turned on.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A quantity of non-toxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window. The airbag inflates in about 30 milliseconds (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Enhanced Accident Response System In the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: • • • • NOTE: Front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE airbag inflation. These airborne particles may irritate Maintaining Your Airbag System the skin, eyes, nose, or throat. If you have skin or eye WARNING! irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation • Modifications to any part of the airbag system continues, see your doctor. If these particles settle on could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! (Continued) • Do not attempt to modify any part of your airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any airbag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE located on the inside of the fuse block cover for the • How far (if at all) the driver was depressing the proper airbag fuses. See your authorized dealer if the accelerator and/or brake pedal; and, fuse is good. • How fast the vehicle was traveling. Event Data Recorder (EDR) These data can help provide a better understanding of This vehicle is equipped with an event data recorder the circumstances in which crashes and injuries occur. (EDR).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR. Child Restraints Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Small Children • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. LATCH child restraint anchorage system. Refer to “Lower Anchors and Tether for CHildren (LATCH)”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. NOTE: For additional information, refer to www.seatcheck.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt restraint: comfortably and whose legs are long enough to bend • Before buying any restraint system, make sure that it over the front of the seat when their back is against the has a label certifying that it meets all applicable Safety seatback should use the lap/shoulder belt in a rear seat. Standards.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 some time. In fact, many child restraint manufacturers NOTE: will provide add-on tether strap kits for some of their • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not older products. being used for occupant restraints are stowed and out Because the lower anchorages are to be introduced to of reach of children.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing The Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH mechanisms in the center position of a Quad Cab威 rear seat, or Crew Cab model with a bench rear seat. A child may be placed in the rear center seating position of a Quad Cab威, or Crew Cab bench model using the seat belt and child tether anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. then allow the belt to retract into the retractor. For additional information on ALR, refer to “Automatic Locking Mode”.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Tether Anchor Child restraints having tether straps and hooks for connection to tether anchors have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for their older products. Regular Cab models have two tether anchorages, one each behind the front center and right seats. Quad Cab威, Mega Cab威 and Crew Cab models have three anchorages, one behind each of the rear seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Installation Sequence (Quad Cab威/Crew Cab/Mega Cab威 - Rear Seats) Mega Cab威 1. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and then to the anchor directly behind the center rear seat. 2. Lift the cover, and attach the hook to the square opening in the sheet metal. Mega Cab威 Tether Strap Mounting 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Quad Cab威/Crew Cab 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by raising the head restraint and reaching between the rear glass and rear seat. 2 Head Restraint Adjustment 2.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the anchor loop. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an accident. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS WARNING! (Continued) Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 If it is necessary to sit in a parked vehicle with the engine inspect the exhaust system each time the vehicle is raised running, adjust your heating or cooling controls to force for lubrication or oil change. Replace as required. outside air into the vehicle. Set the blower at high speed.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 WARNING! (Continued) • Check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 93 ▫ Automatic Dimming Mirror — If Equipped . . . 94 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 95 ▫ Outside Mirrors Folding Feature . . . . . . . . . . 95 ▫ Power Mirrors — If Equipped . . . . . . . . . . . . 96 ▫ Power Folding Outside Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Power Lumbar — If Equipped . . . . . . . . . . . 104 ▫ Self-Limiting Control . . . . . . . . . . . . . . . . . . 119 ▫ Heated Seats — If Equipped . . . . . . . . . . . . 104 ▫ Driver Easy Exit And Easy Entry Control . . . 120 ▫ Ventilated Seats — If Equipped . . . . . . . . . . 107 䡵 To Open And Close The Hood . . . . . . . . . . . . 120 ▫ Manual Seat Adjuster — If Equipped . . . . . . 108 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 127 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 127 䡵 Windshield Wipers And Washers . . . . . . . . . . 129 ▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . 129 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 130 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 131 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . .
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Parkview威 Rear Back Up Camera — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 ▫ Turning Parkview威 On Or Off — With Navigation/Multimedia Radio . . . . . . . . . . . 149 ▫ Turning Parkview威 On Or Off — Without Navigation/Multimedia Radio . . . . . . . . . . . 149 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 157 ▫ General Information . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 161 ▫ Glove Box Storage . . . . . . . . . . . . . . . . . . . 171 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 161 ▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . 173 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 162 ▫ Center Storage Compartment — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 174 䡵 Cigar Lighter And Ash Receiver — If Equipped .
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Power Sliding Rear Window — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 181 ▫ Manual Sliding Rear Window — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 181 䡵 Fold Flat Load Floor — If Equipped . . . . . . . . 181 䡵 Rambox威 — If Equipped . . . . . . . . . . . . . . . . 184 ▫ Rambox威 Integrated Box Side Storage Bins . . 184 ▫ Rambox威 Safety Warning . . . . . . . . . . . . . . . 187 ▫ Bed Extender — If Equipped . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). 3 Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle).
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Outside Mirrors Folding Feature All exterior mirrors are designed to be able to be manually folded both forward and rearward to prevent damage. WARNING! 3 Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Power Mirror Controls The power mirror controls consist of mirror select buttons and a four-way mirror control switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 3 Power Mirror Controls Power Mirror Movement Power Folding Outside Mirrors — If Equipped If equipped with power folding mirrors, they can be To adjust a mirror, press the mirror select button for the electrically folded rearward and unfolded into the drive mirror that you want to adjust. Using the mirror control position.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 35 mph (56 km/h), the fold feature will be disabled, however the mirrors will attempt to unfold at any speed. If you attempt to unfold the mirrors at high speeds, they may not fully unfold - slow down and try again. The switch for the power folding mirrors is located between the power mirror switches L (left) and R (right).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Driver’s Automatic Dimming Mirror — If Equipped The driver’s outside mirror will automatically adjust for glare from vehicles behind you.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position. Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped in or out).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 NOTE: Fold the trailer towing mirrors rearward prior to Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a hands-free system that allows you entering an automated car wash. to use voice commands to dial a phone number stored in A small blindspot mirror is located next to main mirror your mobile phone. Press the Uconnect™ Phone button and can be adjusted separately.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the Lumbar Control Switch power seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 WARNING! CAUTION! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select HIGHlevel heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF. before automatically shutting OFF. The heated seats can shut OFF early or may not turn on when the seat is already warm. Vehicle Equipped With Remote Start On models that are equipped with remote start, the driver’s heated seat can be programmed to come on during a remote start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 indicator lights in each switch indicate the level of heat in normal HIGH-level. If the HIGH-level setting is selected, use. Two indicator lights will illuminate for HIGH, one the system will automatically switch to LOW-level after a maximum of 60 minutes of continuous operation. At that for LOW and none for OFF. time, the number of illuminated LEDs changes from two Press the switch once to select HIGHto one, indicating the change.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to choose HIGH, press it a second time to choose LOW. Pressing the switch a third time will turn the ventilated seat OFF. When HIGH speed is selected both lights on the switch will be illuminated. When LOW speed is selected one light will be illuminated. Manual Seat Adjuster — If Equipped Both front seats are adjustable forward or rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seatbelts and while the vehicle is parked.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. • To avoid injury, place your hand on the seatback and actuate the handle, then position the seatback in the desired position. 40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Folding Rear Seat (Table Mode) — If Equipped Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint. Rear Seat Recliner Handle WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback forward. Table Mode 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding Rear Seat — If Equipped Both the outboard rear seats will drop and move forward when the seatback is folded flat. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 To fold either rear seat flat: 2. Fold the seatback down and push the seat forward. 1. Lift the handle, located on the outboard side of either of the rear seats. 3 Rear Passenger Fold Flat Seats Handle 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! An improperly latched seat could cause serious injury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 3 Adjustment Button Adjustment Button Rear Head Restraints NOTE: The two outboard seat are equipped with adjustable head • The rear center head restraint (Crew Cab and Quad restraints. To raise the head restraint, pull upward on the Cab) has only one adjustment position that is used to head restraint. To lower the head restraint, press the aid in the routing of a tether.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer. DRIVER MEMORY SEAT — IF EQUIPPED Driver memory seats allow the driver to recall settings for the adjustable pedals, mirrors, seats and the radio presets using the key fob. The memory seat buttons are located on the outboard side of the drivers seat cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Keyless Entry (RKE) transmitters can also be pro- 2. Adjust the driver’s seat, recliner, and both sideview grammed to recall the same positions when the UN- mirrors to the desired positions. LOCK button is pressed. NOTE: Not all motors may be moved at one time. Refer NOTE: The power lumbar option is not programmable to “Power Seats — If Equipped” in this section for further information. with driver memory seats.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s seat or the 9. Press and release the LOCK button on one of the RKE UNLOCK button on the RKE transmitter linked to transmitters. memory position 2. 10.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 vehicles equipped with the Electronic vehicle Information Center (EVIC), refer to “Electronic Vehicle Informa1. Turn the ignition switch to the OFF position and tion Center (EVIC)/Customer-Programmable Features” remove the key. in “Understanding Your Instrument Panel” for further 2. Press and release the memory SET button located on information. the driver’s seat. Self-Limiting Control 3.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Easy Exit And Easy Entry Control This additional feature provides automatic driver’s seat positioning which will enhance driver mobility into and out of the vehicle. The seat cushion will move rearward approximately 2.5 in (60 mm) when the key is removed from the ignition switch. The seat will move forward approximately 2.5 in (60 mm) when the key is placed into the ignition and turned out of the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. 3 WARNING! Be sure the hood is fully latched before driving your vehicle.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE parking lights, instrument panel lights, cargo lights and Your vehicle is equipped with plastic headlight and fog fog lights (if equipped). light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Headlights To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position. 3 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running before the head- Parking Lights And Panel Lights To turn on the parking lights and instrument panel lights will turn on in the Automatic Mode. lights, rotate the headlight switch clockwise to the Headlight Delay parking light symbol. To turn off the parking lights, To aid in your exit, your vehicle is equipped with a rotate the headlight switch back to the O (Off) position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the bottom of the switch) is rotated to the far right detent position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE supplement the brightness of the odometer, trip odom- Cargo Light eter, radio and overhead console by rotating the control The cargo lights are turned on by pressing on the cargo to the right until you hear a click. This feature is termed button. the “Parade” mode and is useful when headlights are required during the day.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Lights-On Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 High/Low Beam Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. High/Low Beam Switch WINDSHIELD WIPERS AND WASHERS Windshield Wipers The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the low continual speed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or cushion.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals cannot be adjusted when the vehicle is in WARNING! REVERSE or when the Electronic Speed Control System is on. The following messages will be displayed Do not adjust the pedals while the vehicle is moving. on vehicles equipped with the Electronic Vehicle In- You could lose control and have an accident. Always formation System (EVIC) if the pedals are attempted to adjust the pedals while the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button (located in the end of the lever) once and the cruise indicator light (located in the message window of the cluster) will illuminate showing that the Electronic Speed Control system is on.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it. To Set A Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press the SET lever downward and then release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED The ParkSense威 Rear Park Assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.g. during a parking maneuver. Refer to ParkSense威 System Usage Precautions for limitations of this system and recommendations.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 audible warnings to indicate the distance between the ParkSense姞 Display When the vehicle is in REVERSE, the warning display rear fascia/bumper and the detected obstacle. will turn ON indicating the system status.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Park Assist System Off The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 3 Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Distance (in/cm) Audible Alert Chime Display Message Greater than 79 in (200 cm) None Park Assist ON Arcs None Radio Mute No WARNING ALERTS 79-39 in 39-25 in (200-100 cm) (100-65 cm) Single 1/2 Slow Second Tone Warning Object Warning Object Detected Detected 3 Solid 3 Slow (Continuous) Flashing Yes Yes NOTE: ParkSense威 will MUTE the radio, if on, when the system is sounding an audio tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 chime, once per ignition cycle, and it will display the “CLEAN PARK ASSIST SENSORS” or the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cleaning The ParkSense姞 System • When you move the shift lever to the REVERSE Clean the ParkSense威 sensors with water, car wash soap position and ParkSense威 is turned off, the instrument and a soft cloth. Do not use rough or hard cloths. Do not cluster will display “PARK ASSIST OFF” message for scratch or poke the sensors. Otherwise, you could damas long as the vehicle is in REVERSE. age the sensors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the instrument cluster. • On vehicles equipped with a tailgate, ParkSense威 should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Turning ParkView姞 On Or Off — With Navigation/Multimedia Radio Turning ParkView姞 On Or Off — Without Navigation/Multimedia Radio 1. Press the “menu” hard-key. 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 2. Select “system setup” soft-key. 3. Press the “camera setup” soft-key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft-key. 4.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE — IF EQUIPPED The overhead console is located on the headliner above the review mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. 3 Rear Passenger Courtesy/Reading Light Front Courtesy/Reading Lights NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons are located in the overhead console designating the different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) NOTE: Some gate operators and garage door openers from the HomeLink威 buttons while keeping the EVIC may require you to replace Step 3 with procedures noted display in view. in the “Gate Operator/Canadian Programming” section. For optimal training, point the battery end of the hand- 4. Press and hold the just-trained HomeLink威 button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor (it is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door). NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. successfully accepted the frequency signal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 The HomeLink威 Universal Transceiver is disabled when Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, the Vehicle Security Alarm is active. follow these steps: Troubleshooting Tips If you are having trouble programming HomeLink威, here 1. Turn the ignition switch to the ON/RUN position. are some of the most common solutions: 2.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located on the overhead Canada RSS-210. Operation is subject to the following console between the courtesy/reading lights. two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a nonabrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation The power sunroof switches remain active for up to open. approximately ten minutes after the ignition switch has Wind Buffeting been turned OFF.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON/RUN or ACC positions for the outlet to provide power.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 The auxiliary power outlets can be found in the following • Inside the upper lid of the center storage compartment locations: — if equipped. • Lower left and lower right of the center stack — without floor mounted shifter. • Inside the top storage tray — with floor mounted shifter.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Rear of the center console storage compartment — The key symbol indicates that this outlet can supply Quad Cab威 or Crew Cab. power when the key is in the ON/RUN or ACC positions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 For vehicles equipped with an optional floor shifter. Optional Floor Shifter 1 — Cigar Lighter 2 — Ash Receiver POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the switch bank below the Climate Controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. 3 CUPHOLDERS Front Instrument Panel Cupholders — (40–20–40 Seats) The cupholders are located in the pull-out tray at the bottom of the center stack.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Mounted Shifter For vehicles equipped with bucket seats and a floor mounted shifter there are two cupholders located in the floor console. Rear Cupholder — Quad Cab姞 Quad Cab威 vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage located in the center armrest. The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Door Storage Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear Door Storage — Crew Cab Storage compartments are located in both the driver and passenger door trim panels.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Center Storage Compartment WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Pull on the upper handle on the front of the armrest to With the upper lid closed, pull on the lower handle to raise the cover. The upper storage area contains a 12 Volt open the lower storage bin. power outlet that can be used to power small electrical devices, refer to “Electrical Power Outlets” for further information.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Second Row In-Floor Storage Bin — If Equipped In-floor storage bins are located in front of the second row seats and can be used for extra storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 NOTE: The front seat may have to be moved forward to Seatback Storage Located in the back of both the driver and passenger fully open the lid. front seats are pockets that can be used for storage.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage (Regular Cab) Storage and Seats (Crew Cab) The storage bin is located behind the front seats and runs The Crew Cab models provide additional storage under the length of the cab. the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. 3 Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Power Sliding Rear Window — If Equipped Manual Sliding Rear Window — If Equipped The switch for the power sliding rear window is located A locking device in the center of the window helps to on the overhead console. prevent entry from the rear of the vehicle. Squeeze the lock to release the window. FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab威 and Crew Cab models with a 60/40 rear seat may be equipped with a folding load floor.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Positioning the Load Floor for Storage Access Under Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the Seat the load floor unfolds into position. 1. Lift the 60/40 seat cushion(s) to the upward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. 3 WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. Load Floor Securing Straps 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RAMBOX姞 — IF EQUIPPED The RamBox威 system is an integrated pickup box storage and cargo management system consisting of three features: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system RamBox姞 Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box. The cargo storage bins provide watertight, lockable, illuminated storage for up to 150 lbs (68 kg) of evenly distributed cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 CAUTION! Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is properly secured. • Do not exceed cargo weight rating of 150 lb (68 kg) per bin. To open a storage bin, press and release the button located on the lid. The RamBox威 lid will open upward to allow hand access. Lift the lid to fully open.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The interior of the RamBox威 will automatically illuminate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the lights back on. CAUTION! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 CAUTION! (Continued) • Loads applied to the top of the bin lid should be minimized to prevent damage to the lid and latching/hinging mechanisms. • Damage to the RamBox威 bin may occur due to heavy/sharp objects placed in bin that shift due to vehicle motion. In order to minimize potential for damage, secure all cargo to prevent movement and protect inside surfaces of bin from heavy/sharp objects with appropriate padding.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox威 Storage Bin Cover Emergency Release Lever — If Equipped As a security measure, a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism. NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark lever attached to the storage bin cover latching mechanism.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 To install the bed extender into the storage position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. With the side gates open, position the extender fully 3. Rotate the side gates closed allowing the outboard forward in the bed against the front panel. ends to be positioned in front of the cargo tie down loops.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 4. Rotate the center handle horizontally to secure the side Divider Position The divider position is intended for managing your cargo gates in the closed position. and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo. Side Gates Closed 5.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the bed extender into a divider position per- 2. With the side gates open, position the extender so the form the following: outboard ends align with the intended slots in the sides 1. Make sure the center handle is unlocked using the of the bed. vehicle key and rotate the center handle vertically to release the extender side gates. Aligning Gate To Slots Center Handle And Lock 1 — Center Handle Lock 2 — Handle 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 4. Rotate the center handle horizontally to secure the side Extender Position The extender position allows you to load the bed of the gates in the closed position. truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position utilizes a locating pin and rotating handle located on both sides of the truck bed near the tailgate. Side Gates Closed 5.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates. 3. Fit the end of the side gate ends onto the pin and handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 4. Rotate the handles to the horizontal position to secure into place. Locking Tab WARNING! To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. • When vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur. There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 out on the cleat and slide it to the detent nearest the To remove the cleats from the utility rail, remove the end desired location. Make sure the cleat is seated in the cap by pushing up on the locking tab, located on the detent and tighten the nut. bottom of the end cap. Slide the cleat off the end of the rail.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SLIDE-IN CAMPERS Disconnecting the Rear Camera — If Equipped 1. Open the tailgate to access the rear camera connector Camper Applications Certain truck models are not recommended for slide-in bracket located on the rear sill. campers. To determine if your vehicle is excluded, please refer to the “Consumer Information Truck-Camper Loading” document available from your authorized dealer. For safety reasons, follow all instructions in this important document.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 2. Remove the connector bracket from the sill by press- 4. Connect the chassis plug and bracket (provided in the ing inward in the locking tab. glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Make sure tailgate is supported when removing 5. Slide the entire tailgate to the right to free the left side support cables. pivot. 6. Remove the tailgate from the vehicle. NOTE: Do not carry the tailgate loose in the truck pickup box. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 205 ▫ EVIC Displays . . . . . . . . . . . . . . . . . . . . . . 229 䡵 Switch Bank Button Description . . . . . . . . . . . 206 ▫ Fuel Economy / Fuel Saver Mode / Distance To Empty (DTE) — If Equipped . . . . . . . . . . 235 ▫ Upper Switch Bank . . . . . . . . . . . . . . . . . . . 206 ▫ Lower Switch Bank . . . . . . . . . . . . . . . . . . . 207 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . .
202 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Customer-Programmable Features (System Setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 䡵 Media Center 130 With Satellite Radio (Sales Code RES+RSC) . . . . . . . . . . . . . . . . . . . . . . . 258 䡵 Media Center 730N/430/430N (RHR/RER/ RBZ/RHB) CD/DVD/HDD/NAV — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ Operating Instructions — Radio Mode . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 203 ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 276 䡵 Video Entertainment System (VES)™ — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . ▫ Controlling The iPod威 Using Radio Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 䡵 Steering Wheel Audio Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Radio Operation . . . . . . . . . . . . . . . . .
204 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Winter Operation . . . . . . . . . . . . . . . . . . . . 300 ▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . 301 ▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . 301 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 302 ▫ Window Fogging And Frosting . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 205 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 6 — — — — — — Headlight Switch Instrument Cluster Radio Upper Switch Bank Upper Glove Compartment Lower Glove Compartment 7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank 10 — Cup Holders 11 — Climate Controls 12 — Power Outlet/Cigar Lighter 13 14 15 16 — — — — Transfer Case Position Switch Ignition Switch Hood Release Parking Brake Release
206 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION Upper Switch Bank 2. ESC OFF Refer to “Starting And Operating” for more information. 3. HAZARD WARNING FLASHER The upper switch bank is located on the center of the Refer to “What To Do In Emergencies” for more inforinstrument panel. mation. 4. 115V POWER INVERTER Refer to “Understanding The Features Of Your Vehicle” for more information. 5. REAR PARK ASSIST Refer to “Understanding The Features Of Your Vehicle” for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 2. VENTILATED SEATS Refer to “Understanding The Features Of Your Vehicle” The lower switch bank is located on the center of the for more information. instrument panel. 3. HEATED STEERING WHEEL Refer to “Understanding The Features Of Your Vehicle” for more information. Lower Switch Bank 4 1. HEATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information.
208 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 209 INSTRUMENT CLUSTER — PREMIUM 4
210 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS • Check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 1. Tachometer The tachometer indicates engine speed in Revolutions Per Minute (RPM x 1000). 3. Fuel Gauge Shows level of fuel in tank when ignition switch is in the CAUTION! ON/RUN position. Do not operate the engine with the tachometer pointer at high RPM for extended periods. Engine damage may occur. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 CAUTION! WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealership for service. A hot engine cooling system is dangerous.
212 UNDERSTANDING YOUR INSTRUMENT PANEL rotate at the same speed. Low range provides a greater If the light remains lit with the engine running, your gear reduction ratio to provide increased torque at the vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. If the light is wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 9. 4WD Auto Indicator 11. TOW/HAUL The 4WD auto indicator will be illuminated The TOW HAUL button is located on the whenever the four-wheel drive mode is autocenter stack upper switch bank. This light will matically engaged. illuminate when TOW HAUL mode is selected. 10. SVC (Service) 4WD 12. Electronic Stability Control (ESC) Activation/ The SVC 4WD light monitors the electric shift Malfunction Indicator Light — If Equipped four-wheel drive system.
214 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on momentarily each time the ignition switch is turned to ON/RUN. 14. Oil Pressure Gauge The pointer should always indicate some oil pressure when the engine is running. A continuous high or low reading under normal driving conditions may indicate a lubrication system malfunction. Immediate service should be obtained from an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 16. Odometer Display / Electronic Vehicle Information Center (EVIC) Display Area — If Equipped Odometer Display The odometer display shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
216 UNDERSTANDING YOUR INSTRUMENT PANEL perform the following: Place the ignition in the ON/ Odometer / Trip Odometer / ECO (Fuel Saver Indicator) RUN, but do not start the engine. With the odometer button to change the display from odometer to either of value displayed, hold the TRIP button down for a period the two trip odometer settings or the “ECO” display. If the vehicle diagnostic system determines of six seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 noFUSE If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE” message will display in the odometer display area. For further information on fuses and fuse locations refer to “Fuses” in “Maintaining Your Vehicle”. CHAngE OIL Your vehicle is equipped with an engine oil change indicator system.
218 UNDERSTANDING YOUR INSTRUMENT PANEL single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Center (EVIC). Refer to ”Electronic Vehicle Information cycling operation is controlled by the engine control Center (EVIC) — If Equipped” for further information. module. Post-heat operation can run for several minutes, and then the electrical system and voltmeter needle will 20. High Beam Indicator stabilize. This indicator shows that headlights are on high beam. Push the multifunction lever forward to 22.
220 UNDERSTANDING YOUR INSTRUMENT PANEL master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. Do not operate the vehicle until the cause is corrected.
222 UNDERSTANDING YOUR INSTRUMENT PANEL As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible. CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 30. Transmission Temperature Warning Light 28. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog This light indicates that there is excessive transmission fluid temperature that might occur lights are on. with severe usage such as trailer towing. It may 29.
226 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. For vehicles equipped with a premium cluster this warning light will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 For vehicles equipped with a premium cluster this indicator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 33. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off.
228 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: Steering wheel EVIC control button, as it appears on the left side of the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Steering wheel EVIC control button, as • Right front turn signal lamp out it appears on the right side of the • Left rear turn signal lamp out steering wheel. • Right rear turn signal lamp out • Service air filter • Check Tire Pressure Press and release the SELECT button for access • Perform service to main menus, sub-menus or to select a per• ESC Off sonal setting in the system setup menu.
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Lights On • Park Assist On • Keyfob Battery Low • Park Assist Off • ECO (Fuel Saver Indicator) — If Equipped • Warning Object Detected • Door(s) Ajar (with a single chime, if vehicle is in • motion) • • Wrong Key • • Damaged Key • • Key not programmed • • Key In Ignition • • Turn Signal On • • RKE Battery Low • • LOW WASHER FLUID • • Oil Change Due > Dealer Info • Left Front Turn Signal Light Out Left Rear Turn Signal Light Out Right Front Turn Signal Light
UNDERSTANDING YOUR INSTRUMENT PANEL 231 • Remote start aborted — Fuel low • Adjustable Pedals Unavailable — Cruise Engaged • Remote start disabled — System fault • To Tow Vehicle Safely, Read Neutral Shift Procedure in Owners Manual • Remote start disabled — Turn key • Remote start active — Key to Run • Remote Start Disabled — Start Vehicle to Reset • Remote Start Active — Insert Key and Turn to RUN EVIC Warning Lights • Door Ajar This light will turn on to indicate that one or more doors may be ajar.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Do not operate the vehicle until the cause is corrected. • Electronic Speed Control Light This light does not show how much oil is in the engine. This light will turn on when the electronic The engine oil level must be checked under the hood. speed control is ON. • Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. shift the transmission into NEUTRAL and idle the vehicle.
234 UNDERSTANDING YOUR INSTRUMENT PANEL • Transmission Temperature Light WARNING! This light indicates that there is excessive transmission fluid temperature that might occur If the Transmission Temperature Warning Light is with severe usage such as trailer towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The Oil Change Due message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.
236 UNDERSTANDING YOUR INSTRUMENT PANEL will appear whenever the Multi-Displacement System Distance To Empty (DTE) (MDS) (if equipped) allows the engine to operate on four Distance To Empty (DTE) Shows the estimated distance cylinders, or if you are driving in a fuel efficient manner. that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Trip Functions • Trip B Press and release the ODOMETER/TRIP ODOMETER Shows the total distance traveled for Trip B since the last button until one of the following Trip Functions displays reset. in the EVIC: • Elapsed Time • Trip A Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed • Trip B time will increment when the ignition switch is in the ON • Elapsed Time or START position.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the available information displays, then press SELECT to display any one of the following choices. • Engine Hours Displays the number of hours of engine operation. • Coolant Temp Displays the actual coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 to “Tires-General Information/Tire Inflation Pressures” in “Starting And Operating” for additional information. • Your system can be set to display pressure units in PSI, kPa, or BAR. Units Press and release the UP or DOWN button until “Units” displays in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Compass / Temperature Display The compass readings indicate the direction the vehicle is facing. The EVIC will display one of eight compass readings and the outside temperature. NOTE: • The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperature is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 NOTE: A good calibration requires a level surface and 4. Press and release the SELECT button to start the an environment free from large metallic objects such as calibration. The “CAL” indicator will be displayed in the buildings, bridges, underground cables, railroad tracks, EVIC. etc. 5.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Laptops and Radar Detectors. This is where the compass 2. Press the UP or DOWN button until the System Setup module is located, and it can cause interference with the (Customer-Programmable Features) menu is reached, then press the SELECT button. compass sensor, and it may give false readings. 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button. The last variance zone number displays in the EVIC. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Press and release the UP or DOWN button until System route, mile by mile, turn-by-turn until the final destination is reached. To make your selection, press and release Setup displays in the EVIC. the SELECT button until a check-mark appears next to Use the UP or DOWN button to display one of the the feature showing the system has been activated or the following choices. check-mark is removed showing the system has been deactivated.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Lock Doors When this feature is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 position using the seat mounted switch. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. Horn With Remote Start When this feature is selected, a short horn sound will occur when the RKE transmitter REMOTE START button is pressed.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Flash Lamps With Lock When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the RKE transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 been deactivated. When this feature is deactivated, the Tilt Mirror In Reverse system reverts to the standard intermittent wiper When this feature is selected and the shift lever is placed in reverse gear, the side mirrors tilt downward to allow operation. the driver to see into the previous blind spot and avoid Easy Exit Seat — If Equipped objects in close proximity to the rear of the vehicle.
248 UNDERSTANDING YOUR INSTRUMENT PANEL highlighted, then press and release the SELECT button feature showing the system has been activated or the until a check-mark appears next to the setting, showing check-mark is removed showing the system has been deactivated. that the setting has been selected. Illuminated Approach When this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the RKE transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/ RHB) CD/DVD/HDD/NAV — IF EQUIPPED MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right NOTE: The sales code is located on the lower right side side of the radio faceplate. of the unit’s faceplate. Refer to your Uconnect™ Multimedia RHR, RER, RBZ or RHB user’s manual for detailed operating instructions.
250 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection. Holding either button will bypass position to operate the radio. stations without stopping, until you release it. Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the knob to save time change. mid-range tones. 5. To exit, press any button/knob, or wait five seconds. Push the rotary TUNE/SCROLL control knob a third RW/FF time and TREBLE will display.
252 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. exit setting tone, balance, and fade. The stations stored in SET 2 memory can be selected by AM/FM Button pressing the pushbutton twice. Press the buttons to select either AM or FM mode. Every time a preset button is used, a corresponding SET/RND Button — To Set the Pushbutton button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
254 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within playing time display to a small CD playing time display. 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
256 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: When using the MP3 encoder to compress audio data to • Level 1: 12 (including a separator ⬙.⬙ and a three- an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit character extension) rates (VBR) are also supported. The majority of MP3 files • Level 2: 31 (including a separator ⬙.⬙ and a three- use a 44.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Playlist files are not supported. MP3 Pro files are not To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a supported. single-session disc, enable the “Disc at Once” option Playback of MP3 Files before writing to the disc. When a medium containing MP3 data is loaded, the radio checks all files on the medium.
258 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Media Center 130 (RES/RSC) Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Power Switch/Volume Control (Rotary) Voice Command System (Radio) — If Equipped Push the ON/VOLUME control knob to turn on the Refer to “Voice Command” in the Uconnect™ User radio. Push the ON/VOLUME control knob a second Manual located on the DVD for further details. time to turn off the radio.
260 UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not 4. Adjust the minutes using the right side TUNE/ available on your vehicle, a “Not Equipped With SCROLL control knob. Press the TUNE/SCROLL control Uconnect Phone” message will display on the radio knob to save time change. screen. 5. To exit, press any button/knob or wait five seconds. TIME Button The clock can also be set by pressing the SETUP button.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
262 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
264 UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/ RND button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism.
266 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button Press the button to select either AM or FM mode. convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Loading times for playback of MP3 files may be affected begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain by the following: playable files). • Media - CD-RW media may take longer to load than The folder list will time out after five seconds.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Uconnect™ Multimedia (Satellite Radio) — If Equipped Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 information, call the toll-free number 888-539-7474, or Sirius ID number will display. The Sirius ID number visit the Sirius web site at www.sirius.com, or at www- display will time out in two minutes. Press any button on the radio to exit this screen. .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Selecting Uconnect™ Multimedia (Satellite) Mode Press the SAT button until ⬙SAT⬙ appears in the display.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will • The vehicle is parked in an underground parking remain tuned to the new channel until you make another structure or under a physical obstacle. selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons channel with the same selected Music Type name.
274 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 This feature allows an iPod威 to be plugged into the Connecting The iPod姞 vehicle’s sound system through a 16–pin connector, using Use the provided connection cable to connect an iPod威 to the vehicle’s 16–pin connector port (which is located in the provided interface cable. the glove compartment on some vehicles). Once the iPod威 control supports Mini, 4G, Photo, Nano, 5G iPod威 iPod威 is connected and synchronized to the vehicle’s and iPhone威 devices.
276 UNDERSTANDING YOUR INSTRUMENT PANEL faceplate. Once in the iPod威 control mode, iPod威 audio Using This Feature By using the provided connection cable to connect an tracks (if available from iPod威) start playing over the iPod威 to the vehicle’s iPod威 control 16–pin connector vehicle’s audio system. port: Play Mode • The iPod威 audio can be played on the vehicle’s sound When switched to iPod威 control mode, the iPod威 autosystem, providing metadata (artist, track title, album, matically starts Play mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.) button long enough will jump to the beginning of for that track. Pressing the INFO button again jumps the current track. to the next screen of data for that track.
278 UNDERSTANDING YOUR INSTRUMENT PANEL Shuffle OFF modes for the iPod威. If the RND icon is showing on the radio display, then the shuffle mode is ON. fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticed. List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode. List mode enables scrolling through the list of menus and tracks on the iPod威.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威. Turn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob.
280 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the radio has a USB port, refer to the appropriate NOTE: This section is for sales code RES and REQ/ Uconnect™ Multimedia radio User’s Manual for REL/RET radios only with Uconnect™. For sales code iPod威 or external USB device support capability.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 NOTE: If the audio device battery is completely discharged, it may not communicate with the iPod威/USB/ MP3 control system until a minimum charge is attained. Leaving the audio device connected to the iPod威/USB/ MP3 control system may charge it to the required level. Using This Feature By using iPod cable or external USB device to connect to USB port: • The audio device can be played on the vehicle’s sound system, providing metadata (artist, track title, album, etc.
282 UNDERSTANDING YOUR INSTRUMENT PANEL Controlling The iPod姞 Or External USB Device Using Radio Buttons To get into the iPod威/USB/MP3 control mode and access a connected audio device, either press the “AUX” button on the radio faceplate or press the VR button and say ⬙USB⬙ or ⬙Switch to USB⬙. Once in the iPod威/USB/MP3 control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 during play mode will jump to the next track in the list, or press the VR button and say ⬙Next or Previous Track⬙. SCAN button again. During Scan mode, pressing the << SEEK and SEEK >> buttons will select the previous and next tracks. • While a track is playing, press the INFO button to see • RND button (available on sales code RES radio only): the associated metadata (artist, track title, album, etc.
284 UNDERSTANDING YOUR INSTRUMENT PANEL • Turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying the track detail on the radio display. Once the track to be played is highlighted on the radio display, press the TUNE control knob to select and start playing the track. Turning the TUNE control knob fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 device, then follow the same steps to go to the desired track in that list. Not all iPod威 or external USB device sub-menu levels are available on this system. • MUSIC TYPE button: The MUSIC TYPE button is another shortcut button to the genre listing on your audio device. CAUTION! • Leaving the iPod威 or external USB device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device.
286 UNDERSTANDING YOUR INSTRUMENT PANEL phone system. Seven devices can be paired to the Previous Track Uconnect™ phone system, but just one can be selected Use the SEEK DOWN button, or press the VR button on the radio and say “Previous Track” to jump to the and played. previous track music on your cellular phone. Selecting Different Audio Device Browse 1. Press PHONE button to begin. Browsing is not available on a BTSA device. Only the 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 • Easy menu-driven functions on touch-screen radios • Video and audio input jacks available in rear seating area • Nine different medias to choose from in each screen (AM, FM, Sirius Radio, DVD1, DVD2, Hard Disc Drive (HDD), AUX in radio, AUX1, AUX2) 4 The LCD screen is located in the overhead compartment console.
288 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. VES™ Remote Control Location NOTE: Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 The right hand control is a rocker type switch with a The button located in the center of the left hand control pushbutton in the center. Pressing the top of the switch will tune to the next pre-set station that you have will increase the volume, and pressing the bottom of the programmed in the radio pre-set pushbuttons. switch will decrease the volume.
290 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particuCD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 throughout the vehicle. The controls are located on the dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions. instrument panel below the radio. NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient temperature.
292 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Panel Mode Mix Mode Air is directed through the outlets in the instrument Air is directed through the floor, defrost and side panel. These outlets can be adjusted to direct airflow. window demist outlets. This setting works best in cold or snowy conditions that require extra heat at Bi-Level Mode the windshield. This setting is good for maintaining Air is directed through the panel and floor outlets. comfort, while reducing moisture on the windshield.
294 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control Press this button to choose between outside air intake or recirculation of the air inside the vehicle. A LED will illuminate when you are in Recirculation mode. Only use the Recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interior rapidly upon initial start-up in very hot or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Economy Mode MAX A/C If ECONOMY mode is desired, press the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired temperature. For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recirculated. Air Conditioning Operation Push this button to engage the Air Conditioning (A/C).
296 UNDERSTANDING YOUR INSTRUMENT PANEL • When occupants in the vehicle select an Auto mode operation, Auto blower operation is set by using rotary knobs on the control unit and a comfort temperature setting by using the temperature up and down buttons. • The system provides set-and-forget operation for optimum comfort and convenience. • The system can be controlled manually, if desired.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 NOTE: • It is not necessary to move the temperature settings for 1. Position the MODE control knob to the Auto position cold or hot vehicles. The system automatically adjusts on the Automatic Temperature Control (ATC) Panel. the temperature, mode and fan speed to provide 2. Position the BLOWER control knob in the Auto posicomfort as quickly as possible. tion on the ATC Panel. • The temperature can be displayed in U.S.
298 UNDERSTANDING YOUR INSTRUMENT PANEL selected. This allows the front occupants to control the Manual Operation This system offers a full complement of manual override volume of air circulated in the vehicle and cancel the Auto mode. features. NOTE: Each of these features operate independently The operator can also select the direction of the airflow from each other. If any one feature is controlled manually, by selecting one of the following positions.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 The Air Conditioning (A/C) button allows the Floor Mode Air comes from the floor outlets. A slight amount of operator to manually activate or deactivate the air conditioning system. When in A/C mode and the air is directed through the defrost and side window ATC is set to a cool temperature, dehumidified air flows demister outlets. through the air outlets.
300 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation mode should only be used temporarily. The recirculation LED will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the Recirculation mode LED and allow outside air into the vehicle. Summer Operation The engine cooling system in air conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 Vacation/Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging and Frosting Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather.
302 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 309 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 313 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 309 ▫ Brake/Transmission Shift Interlock System . . 313 ▫ Automatic Transmission . . . . . . . . . . . . . . . 309 ▫ Four–Speed Automatic Transmission – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Extreme Cold Weather (Below –20°F Or ⫺29°C) . . . . . . . . . . .
304 STARTING AND OPERATING ▫ Shifting Procedure – Manually Shifted Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 328 ▫ Off-Road Driving Tips And Vehicle Characteristics . . . . . . . . . . . . . . . . . . . . . . 347 ▫ Transfer Case Position Indicator Light . . . . . . 329 ▫ Driving In Snow, Mud And Sand . . . . . . . . . 350 ▫ Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped . . . . . . . 329 ▫ Crossing Obstacles (Rocks And Other High Points) . . . . . . . . . .
STARTING AND OPERATING 305 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 366 ▫ Power Steering Fluid Check . . . . . . . . . . . . . 391 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . 367 䡵 Multi-Displacement System (MDS) (If Equipped) — 5.7L Engine Only . . . . . . . . . . 392 ▫ Shallow Standing Water . . . . . . . . . . . . . . . 367 䡵 Off-Road Driving Tips . . . . . . . . . . . . . . . . . . 369 ▫ After Driving Off-Road . . . . . . . . . . . . . . . . 369 䡵 Parking Brake . . .
306 STARTING AND OPERATING ▫ ESC Activation/Malfunction Indicator Light And ESC Off Indicator Light . . . . . . . . . . . . 403 ▫ Spare Tire Matching Original Equipped Tire And Wheel – If Equipped . . . . . . . . . . . . . . 419 ▫ Trailer Sway Control (TSC) – If Equipped . . . 405 ▫ Compact Spare Tire – If Equipped . . . . . . . . 419 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . 406 ▫ Full Size Spare – If Equipped . . . . . . . . . . . . 420 ▫ Tire Markings . . . . . . . . . . . . . .
STARTING AND OPERATING 307 ▫ Directional Tires – If Equipped . . . . . . . . . . . 429 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 445 ▫ Dual Rear Wheels . . . . . . . . . . . . . . . . . . . . 429 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 445 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 430 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . 446 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . 433 ▫ Fuel System Cautions . . . . . . . . . . . . . . . .
308 STARTING AND OPERATING ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . 451 ▫ Towing Requirements . . . . . . . . . . . . . . . . . 463 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 451 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 472 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 452 䡵 Snowplow . . . . . . . . . . . . . . . . . . . . . . . . . . 474 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 453 ▫ 1500 Models Only . . . . . .
STARTING AND OPERATING 309 STARTING PROCEDURES pedal. Turn the key fob to the START position and release Before starting your vehicle, adjust your seat, adjust both when the engine starts. If the engine fails to start within inside and outside mirrors, and fasten your seat belt. 10 seconds, turn the key fob to the OFF position, wait five seconds, then repeat the “Normal Starting” procedure. The starter should not be operated for more than 15second intervals.
310 STARTING AND OPERATING Extreme Cold Weather (Below –20°F or ⫺29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
STARTING AND OPERATING 311 If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key fob once the engine is running smoothly. 1500 Models The engine block heater cord is routed under the hood on the passenger side of the vehicle near the right head lamp assembly.
312 STARTING AND OPERATING WARNING! CAUTION! (Continued) Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING 313 Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Interlock which requires the shift lever to be placed in PARK prior to turning the key fob to the LOCK position. The key fob can only be removed from the ignition switch when the ignition is in the LOCK position. Once the key fob is removed, the shift lever is locked in PARK.
314 STARTING AND OPERATING Gear Ranges Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever in the PARK position.
STARTING AND OPERATING 315 WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key fob from the ignition, and apply the parking brake. Once the key fob is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
316 STARTING AND OPERATING transmission will automatically shift from third gear to If the transmission temperature gets extremely hot, the transmission will automatically select the most desirable OVERDRIVE if the following conditions are present: gear for operation at this temperature.
STARTING AND OPERATING 317 operating in TOW/HAUL mode, the transmission will normal operation. If the TOW/HAUL mode is desired, shift to third gear and fourth gear will be enabled under the switch must be pressed each time the engine is started. steady cruise conditions. Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the Transmission Limp Home Mode will be engaged.
318 STARTING AND OPERATING 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, PARK, REVERSE, and NEUTRAL will continue to operate. Only second gear will operate in the DRIVE position. Have the transmission checked at your authorized dealer as soon as possible.
STARTING AND OPERATING 319 into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second gear) or 1 (first gear), when needed. 5 Console Shift Lever Column Shift Lever On vehicles equipped with 4.7L or 5.7L engines, use of ERS (or TOW/HAUL mode) also enables an additional underdrive gear which is not normally used during through-gear accelerations. This additional gear improves vehicle performance and cooling capability when towing a trailer on certain grades.
320 STARTING AND OPERATING through third gear are underdrive gears, and fourth gear is direct drive. ERS fifth gear (Overdrive) is the same as the normal fourth gear. When in the DRIVE position in first through fourth gear, the first tap down (-), will display the ERS designation for the current gear (the transmission will not downshift).
STARTING AND OPERATING 321 Gear Ranges Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever in the PARK position.
322 STARTING AND OPERATING WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key fob from the ignition, and apply the parking brake. Once the key fob is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
STARTING AND OPERATING 323 Overdrive Operation The Overdrive automatic transmission contains an electronically controlled fourth and fifth gear (Overdrive). The transmission will automatically shift from DRIVE to Overdrive if the following conditions are present: operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level.
324 STARTING AND OPERATING performance and reduce the potential for transmission closed-throttle downshifts to third gear are performed overheating or failure due to excessive shifting. When (for improved braking) when driving conditions warrant. operating in the TOW/HAUL mode, fifth gear is disThe “TOW/HAUL Indicator Light” will illuminate in the abled and 2-3 and 3-4 shift patterns are modified. instrument cluster to indicate when the switch has been activated.
STARTING AND OPERATING 325 NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant (antifreeze) are warm [usually after 1 to 3 miles (1.6 to 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal.
326 STARTING AND OPERATING When additional traction is required, the 4H and 4L positions can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by simply moving the shift lever to the desired positions. The 4H and 4L positions are intended for loose, slippery road surfaces only. Driving in the 4H and 4L positions on dry, hard surfaced roads may cause increased tire wear and damage to the driveline components.
STARTING AND OPERATING 327 NOTE: Delayed shifts out of four-wheel drive may be For additional information on the appropriate use of each experienced due to uneven tire wear, low or uneven tire transfer case mode position, see the information below: pressures, excessive vehicle loading, or cold tempera2H tures. Rear-Wheel Drive High Range - This range is for normal street and highway driving on dry hard surfaced roads.
328 STARTING AND OPERATING 4L Four-Wheel Drive Low Range - This range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). 2H Or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into NEUTRAL.
STARTING AND OPERATING 329 method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). • Do not attempt to shift into or from 4L while the transmission is in gear. Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
330 STARTING AND OPERATING This electronically shifted transfer case provides four section for specific shifting instructions. The 4WD LOCK and 4WD LOW positions are designed for loose, slippery mode positions: road surfaces only. Driving in the 4WD LOCK and 4WD • Two-wheel drive high range (2WD) LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline compo• Four-wheel drive lock range (4WD LOCK) nents.
STARTING AND OPERATING 331 the control knob back to the current position, wait five seconds, and retry selection. To find the shift require1. The current position indicator light will turn OFF. ments, refer to the ⬙Shifting Procedure⬙ for your transfer 2. The selected position indicator light will flash until the case, located in this section. transfer case completes the shift. The “SVC 4WD Warning Light” monitors the electronic 3.
332 STARTING AND OPERATING NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning, as this can cause damage to driveline components. When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h).
STARTING AND OPERATING 333 4WD LOCK Shifting Procedure Four-Wheel Drive Lock Range - This range locks the front NOTE: and rear driveshafts together forcing the front and rear • If any of the requirements to select a new transfer case wheels to rotate at the same speed. This range provides position have not been met, the transfer case will not additional traction for loose, slippery road surfaces only. shift.
334 STARTING AND OPERATING 2WD⇔ 4WD LOCK Rotate the 4WD control switch to the desired position. Shifts between 2WD and 4WD LOCK can be done with the vehicle stopped or in motion. With the vehicle in motion, the transfer case will engage/disengage faster if you momentarily release the accelerator pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the ON position with the engine either running or off.
STARTING AND OPERATING 335 Alternate Procedure NOTE: • If Steps 1 or 2 of either the Preferred or Alternate 1. Bring the vehicle to a complete stop. Procedure are not satisfied prior to attempting the shift, then the desired position indicator light will flash 2. With the ignition switch in the ON position and the continuously while the original position indicator light engine either OFF or running, shift the transmission into is ON, until all requirements have been met. NEUTRAL. 3.
336 STARTING AND OPERATING Electronically Shifted Transfer Case (Five-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
STARTING AND OPERATING 337 drive will be automatically engaged when the vehicle senses a loss of traction. Because the front axle is engaged, this mode will result in lower fuel economy than the 2WD mode. left hand corner of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational Towing” in “Starting and Operating” for further information.
338 STARTING AND OPERATING If One Or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. after engine start up or illuminates during driving, it means that the four-wheel drive system is not functioning properly and that service is required.
STARTING AND OPERATING 339 Proper operation of four-wheel drive vehicles depends For additional information on the appropriate use of each on tires of equal size, type and circumference on each transfer case mode position, see the information below: wheel. Any difference in tire size can cause damage to the 2WD drivetrain. Rear-Wheel Drive High Range - This range is for normal Because four-wheel drive provides improved traction, street and highway driving on dry hard surfaced roads.
340 STARTING AND OPERATING 4WD LOW Four-Wheel Drive Low Range - This range provides low speed four-wheel drive. Locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). position will remain ON, and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
STARTING AND OPERATING 341 the vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelerator pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the ON position with the engine either running or OFF. This shift cannot be completed if the ignition switch is in the ACC position. 2. Shift the transmission into NEUTRAL. 2WD Or 4WD AUTO Or 4WD LOCK ⇔ 4WD LOW Alternate Procedure 3.
342 STARTING AND OPERATING NOTE: • If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process, the desired position indicator light will flash continuously while the original position indicator light is ON, until all requirements have been met. • The ignition switch must be in the ON position for a shift to take place and for the position indicator lights to be operable.
STARTING AND OPERATING 343 CAUTION! (Continued) • Do not try to lock the rear axle if the vehicle is stuck and the tires are spinning. You can damage drivetrain components. Lock the rear axle before attempting situations or navigating terrain, which could possibly cause the vehicle to become stuck. NOTE: Even when the axles are in the AXLE UNLOCK position, the limited slip differential in the rear axle still provides torque biasing capability for moderate low traction environments.
344 STARTING AND OPERATING LOCK or FRONT/REAR LOCK position, drive the ve- To unlock the front axle; move the axle locker switch to hicle in a turn or on loose gravel to expedite the locking REAR LOCK. The FRONT/REAR LOCK indicator light action. will go out when the axle is unlocked. WARNING! Do not use the locked axle position for normal driving. A locked front axle is intended for off-road driving only. Locking the front axle during on-road driving will reduce the steering ability.
STARTING AND OPERATING 345 Due to the use of taller springs, this vehicle has an increased ride height of approximately 1.9 in (48.3 mm) in the front and 1.5 in (38.1 mm) in the rear. A major advantage to increasing ride height is the positive effect it has on approach/departure and break over angles. This system is controlled by the electronic control sway bar switch located on the instrument panel. 5 1 — On Road 2 — Off Road The switch has two positions; On-Road and Off-Road.
346 STARTING AND OPERATING WARNING! Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result in serious injury. The front stabilizer bar enhances vehicle stability and is necessary for maintaining control of the vehicle. The system monitors vehicle speed and will attempt to reconnect the stabilizer bar at speeds over 18 mph (29 km/h).
STARTING AND OPERATING 347 WARNING! If the stabilizer/sway bar will not return to On-Road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your local service center for assistance. (ORV) trails or recreation areas. You should always tread lightly and only use established roads, trails or ORV recreational areas.
348 STARTING AND OPERATING distance up the ramp divided by the wheelbase of the vehicle and multiplied by 1,000 is the RTI. This vehicle has an RTI of 655, which means you can articulate one front wheel 32 inches in the air while the other three wheels remain in contact with the ground. Water Fording Characteristics Water fording characteristic is the vehicle’s ability to cross a body of still water, where the powertrain and drivetrain are safe from water ingestion.
STARTING AND OPERATING 349 your vehicle’s steering, handling and traction. Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, turns or braking. In most cases there are no road signs, posted speed limits or signal lights. Therefore you will need to use your own good judgment on what is safe and what isn’t.
350 STARTING AND OPERATING Driving In Snow, Mud And Sand CAUTION! There is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to On icy or slippery roads, do not downshift at high steering, acceleration and braking inputs. Therefore you engine RPMs or vehicle speeds because engine brakshould accelerate slowly, leave greater stopping distances ing may cause skidding and loss of control. and avoid abrupt vehicle maneuvers.
STARTING AND OPERATING 351 • Sand – Soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneuvers and maintaining the vehicle’s momentum.
352 STARTING AND OPERATING forward until it makes contact with the object. Apply the Crossing Large Rocks throttle lightly while holding a light brake pressure and When approaching large rocks, choose a path which ensures you drive over the largest with your tires. This ease the vehicle up and over the object. will lift your undercarriage over the obstacle. The tread of WARNING! the tire is tougher and thicker than the side wall and is designed to take the abuse.
STARTING AND OPERATING 353 independently. You need to use caution when crossing accelerator to avoid spinning the log out from under your large obstacles with steep sides. Do not attempt to cross tires. Then ease the vehicle off the log using your brakes. any large obstacle with steep sides at an angle great CAUTION! enough to put the vehicle at risk of a rollover.
354 STARTING AND OPERATING CAUTION! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. the vehicle if something goes wrong? If everything looks good and you feel confident, then change transmission into a lower gear, shift the transfer case into 4L (Low) and proceed with caution. You should use first gear and 4L (Low Range) for very steep hills.
STARTING AND OPERATING 355 fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes. ability to proceed then make sure you are in 4L (Low Range) with the transmission in first gear (manually select first gear on automatic transmissions) and proceed with caution.
356 STARTING AND OPERATING sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle heading slightly up or down. WARNING! Driving across an incline increases the risk of a rollover, which may result in severe injury. • If You Stall Or Begin To Lose Headway – If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake. Restart the engine and shift into REVERSE.
STARTING AND OPERATING 357 your vehicle’s abilities and be able to recover it if CAUTION! something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested Water ingestion into the axles, transmission, transfer water into the engine air intake. If the engine stalls do not case, engine or vehicle interior can occur if you drive attempt to restart it. Determine if it has ingested water too fast or through too deep of water. Water can cause first.
358 STARTING AND OPERATING crossing is the water depth, current and bottom conditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. • Crossing Puddles, Pools, Flooded Areas Or Other Standing Water – Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters.
STARTING AND OPERATING 359 downstream out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obstacles, then cross at an angle heading slightly upstream using the low and slow technique. WARNING! Never drive through fast moving deep water. It can push your vehicle downstream, sweeping it out of control.
360 STARTING AND OPERATING Vehicle Recovery If you drive off-road, you may encounter a situation where you will need to recover your vehicle. Vehicle recovery should always be given consideration before attempting a questionable obstacle. You should never go off-road driving without the ability to recover your vehicle from a situation. Having another vehicle with you usually works best for most situations. The first thing to do is assess the situation.
STARTING AND OPERATING 361 vehicle from DRIVE to REVERSE, while applying CAUTION! throttle after each shift. During this process, for additional traction, try turning your steering wheel quickly Damage can occur when spinning your tires at an back and forth no more than a 1⁄4 turn. If you are stuck excessive high speed. Do not spin your tires faster in mud, sand, or snow try spinning your tires during than an indicated 35 mph (56 km/h).
362 STARTING AND OPERATING two tow straps together using a 1 1⁄2 inch hard wood WARNING! dowel. This will keep the straps from becoming knotted and is safer than using a clevis pin if the strap Never use tow straps with end hooks or link two breaks. Next have the tow vehicle backup, leaving two straps with a clevis pin. These heavy metal objects to three feet worth of slack in the strap.
STARTING AND OPERATING 363 as you power the winch in. Be careful not to allow out of the situation in a slow controlled manner. This slack in the cable as you recover the vehicle. Do not try control works well for avoiding further vehicle damto guide the cable into the drum. If it starts to bunch age. Once you decide it is time to use the winch look up on one end, let it. You can re-spool the cable for a good anchor point. It needs to be strong enough afterwards.
364 STARTING AND OPERATING always a good idea to check for damage. That way you • After extended operation in mud, sand, water, or can get any problems taken care of right away and have similar dirty conditions, have the radiator, fan, brake your vehicle ready when you need it. rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and WARNING! exhaust system for damage.
STARTING AND OPERATING 365 LIMITED-SLIP DIFFERENTIAL WARNING! The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when On vehicles equipped with a limited-slip differential there is a difference between the traction characteristics never run the engine with one rear wheel off the of the surface under the right and left rear wheels.
366 STARTING AND OPERATING erratically to the right or left. This phenomenon occurs 1. Slow down during rainstorms or when the roads are when there is a difference in the surface traction under slushy. the rear (driving) wheels. 2. Slow down if the road has standing water or puddles. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision.
STARTING AND OPERATING 367 Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you.
368 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING 369 OFF-ROAD DRIVING TIPS Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns slowly and cautiously. always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it.
370 STARTING AND OPERATING • After extended operation in mud, sand, water, or WINCH USAGE (POWER WAGON ONLY) — IF similar dirty conditions, have the radiator, fan, brake EQUIPPED rotors, wheels, brake linings, and axle yokes inspected Things To Know Before Using Your Winch and cleaned as soon as possible. General Winch Information WARNING! Your vehicle is equipped with an electric vehicle recovery winch.
STARTING AND OPERATING 371 2. Attach the hook to a suitable anchor point. Low Voltage Interrupt Your winch is equipped with a device that will interrupt CAUTION! winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out Be certain the anchor will withstand the load refor 30 seconds if this device is tripped. If the interrupt is quired to tension the wire rope.
372 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components
STARTING AND OPERATING 373 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection switch to be disconnected from the winch motor to allow the that automatically stops motor function in the power-in wire rope to be pulled from the winch by hand. direction if the motor gets too hot. 7. Remote Control: The remote control provides the 2.
374 STARTING AND OPERATING Winch Accessories The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protective gloves while operating the winch or handling the wire rope. Avoid loose fitting clothes or anything that could become entangled in the wire rope and other moving parts.
STARTING AND OPERATING 375 Clevis/D-Shackles: The Operating Your Winch D-Shackle is a safe means of WARNING! connecting the looped ends of cables, straps and snatch Failure to observe any of these warnings regarding blocks. The shackle’s pin is proper winch usage may result in severe injury. threaded to allow easy re• Always use supplied hook strap to hold the hook moval. when spooling wire rope in or out. • Never use as a hoist. • Never use to move persons.
376 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Always stand clear of wire rope and load and keep others away during winching. • Always keep hands and clothing clear of the wire rope, hook and fairlead opening during operation and when spooling. • Never wrap wire rope back onto itself. Always use a choker chain, wire choker rope or tree trunk protector on the anchor. • Never attach a recovery strap to the winch hook to increase the length of a pull.
STARTING AND OPERATING 377 General Information Vehicle Recovery Using The Winch Practice using your winch before you get stuck. Some key CAUTION! points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. 2. Always take your time when using a winch. 3. Use the right equipment for the situation. 4. Always wear leather gloves and do not allow the wire rope to slip through your hands when handling the rope. 5.
378 STARTING AND OPERATING CAUTION! (Continued) • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers. Watch and listen to Winch for proper snugness. 1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves. 3.
STARTING AND OPERATING 379 4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point. Attach the hook strap to the hook (if not attached).
380 STARTING AND OPERATING 5. Pull the wire to the anchor point. Pull out enough wire 6. Secure to the anchor point. Once you have established rope to reach your anchor point. Be sure to keep a certain your anchor point, secure the tree-trunk protector or amount of tension on the wire as it can become twisted choker-chain around the object. and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work.
STARTING AND OPERATING 381 CAUTION! Always be certain the anchor you select will withstand the load. 7. Attach the Clevis/D-shackle and Tree Trunk Protector. Attach the shackle to the two ends of the strap or chain and through the hook loop, being careful not to over tighten (tighten and back-off 1/2 turn). NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks.
382 STARTING AND OPERATING NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door. Always disconnect the remote control when not in use. 10. Put wire rope under tension.
STARTING AND OPERATING 383 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. 5 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure.
384 STARTING AND OPERATING 13. In certain situations you the vehicle and never near the wire rope or snatch may decide to throw a heavy block. Your situation may have other ⴖno peopleⴖ zones. blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approach or move the blanket once tension is applied.
STARTING AND OPERATING 385 For additional assistance, the winched vehicle can be NOTE: slowly driven while being pulled by the winch. Continue • Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the pulling until the vehicle is on stable ground. If you are winch motor to cool down. able to drive the vehicle, the winching operation is complete.
386 STARTING AND OPERATING section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle’s is complete, be sure to secure the vehicle’s brakes and put the transmission in PARK. Release tension in the wire rope. 17. Disconnect the wire rope, and disconnect from the anchor. 18. Rewind the wire rope.
STARTING AND OPERATING 387 Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary. Keep the wire rope under light tension and spool the wire rope back and onto the winch drum in even layers. Stop frequently to tighten and straighten the layers as necessary.
388 STARTING AND OPERATING Rigging Techniques How To Change The Pulling Direction Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or maintaining a straight-line pulling situation. You will have to assess what technique is correct for your situation. Think ⬙safety⬙ at all times.
STARTING AND OPERATING 389 will enable you to change your pulling direction while Double Line still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing Pulling Power In some cases, you may find yourself needing more pulling power. The use of snatch blocks increases mechanical advantage and that increases your pulling power.
390 STARTING AND OPERATING vehicle’s frame/tow hook and run the wire rope through NOTE: a snatch block. Disengage the clutch and, using the • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that snatch block, pull out enough wire to reach your anchor there is a problem with the power steering system. point. Do not attach the hook to the mounting kit.
STARTING AND OPERATING 391 CAUTION! CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty.
392 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, pull the parking brake release handle.
STARTING AND OPERATING 393 When the parking brake is applied with the ignition make it difficult to move the shift lever out of PARK. The switch ON, the “Brake Warning Light” in the instrument parking brake should always be applied whenever the driver is not in the vehicle. cluster will illuminate. NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver.
394 STARTING AND OPERATING WARNING! (Continued) • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury. Also, be certain to leave the transmission in PARK. Failure to do so may cause the vehicle to roll and cause damage or injury.
STARTING AND OPERATING 395 NOTE: Under cold temperatures, pedal effort will be NOTE: ABS improves steering control of the vehicle higher than normal until the power steering fluid reaches during hard braking maneuvers. operating temperature.
396 STARTING AND OPERATING Traction Control System (TCS) – If Equipped The TCS monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s), and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING 397 WARNING! • The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
398 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., The system will work in REVERSE and all forward gears, vehicle facing uphill is in forward gear; vehicle back- and will not activate if the vehicle is placed in ing uphill is in REVERSE gear). NEUTRAL. WARNING! There may be situations on minor hills (i.e.
STARTING AND OPERATING 399 WARNING! WARNING! (Continued) • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
400 STARTING AND OPERATING 3. With the engine running and the brake applied, rotate EVIC Equipped Vehicles the steering wheel 180° counterclockwise from center. HSA is a Customer Programmable Feature on a EVIC equipped vehicle. If you wish to turn off the HSA feature, 4. Press the “ESC Off” switch four times within 20 secrefer to “Electronic Vehicle Information Center (EVIC)/ onds. The “ESC Off Indicator Light” should appear and Customer Programmable Features” in “Understanding disappear four times.
STARTING AND OPERATING 401 the intended path, ESC applies the brake of the appro- this mode. This mode should be used for almost all priate wheel to assist in counteracting the oversteer or driving situations. ESC should only be turned to “Partial Off” or “ESP Off” for specific reasons as noted below. understeer condition. • Oversteer - when the vehicle is turning more than ESC Partial Off This mode is entered by momentarily pressing the “ESC appropriate for the steering wheel position. Off” switch.
402 STARTING AND OPERATING mode by pressing the “ESC Off” switch. Once the situation requiring ESC to be switched to the “Partial Off” mode is overcome, turn ESC back on by momentarily pressing the “ESC Off” switch. This may be done while the vehicle is in motion. WARNING! In the “Partial Off” mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESC is unavailable.
STARTING AND OPERATING 403 into the PARK position from any other position and then the transfer case (if equipped) is shifted from 4WD LOCK moved out of the PARK position. This will occur even if or NEUTRAL, to 4WD LOW, the ESC system will be in this mode. the message was previously cleared. In this mode, ESC and TCS except for the “limited slip” WARNING! feature described in the TCS section are turned off until the vehicle reaches a speed of 40 mph (64 km/h).
404 STARTING AND OPERATING Light” comes on continuously with the engine running, a NOTE: malfunction has been detected in the ESC system. If this • The “ESC Activation/Malfunction Indicator Light” and the “ESC OFF Indicator Light” come on momenlight remains on after several ignition cycles, and the tarily each time the ignition switch is turned ON.
STARTING AND OPERATING 405 Trailer Sway Control (TSC) – If Equipped The TSC system uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sway of the trailer. TSC will become active automatically once an excessively swaying trailer is recognized. No driver action is required.
406 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 407 Tires designed to this standard have the letter “T” • High flotation tire sizing is based on U.S. design molded into the sidewall preceding the size designastandards and it begins with the tire diameter molded tion. Example: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
408 STARTING AND OPERATING EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 409 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
410 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
STARTING AND OPERATING 411 Tire Loading And Tire Pressure Tire And Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
412 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 413 available cargo and luggage load capacity is 650 lbs NOTE: (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities [295 kg]). of your vehicle with varying seating configurations 5. Determine the combined weight of luggage and cargo and number and size of occupants. This table is for being loaded on the vehicle.
414 STARTING AND OPERATING
STARTING AND OPERATING 415 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
416 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar or rear edge of the driver’s side door.
STARTING AND OPERATING 417 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter.
418 STARTING AND OPERATING loading may be required for high-speed vehicle opera- Radial Ply Tires tion. Refer to original equipment or an authorized tire WARNING! dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly. The instability could cause a collision.
STARTING AND OPERATING 419 Spare Tire Matching Original Equipped Tire And CAUTION! Wheel – If Equipped Your vehicle may be equivalent with a spare tire and Because of the reduced ground clearance, do not take wheel in look and function as the original equipment tire your vehicle through an automatic car wash with a and wheel found on the front or rear axle of your vehicle. compact, full size or limited-use temporary spare This spare tire may be used in the tire rotation for your installed.
420 STARTING AND OPERATING Since this tire has limited tread life the original equip- Full Size Spare – If Equipped ment tire should be repaired (or replaced) and reinstalled The full size spare is for temporary emergency use only. This tire may look like the original equipped tire on the on your vehicle at the first opportunity. front or rear axle of your vehicle, but it is not. This spare Do not install a wheel cover or attempt to mount a tire may have limited tread life.
STARTING AND OPERATING 421 your original equipment tire, replace (or repair) the Tire Spinning original equipment tire and reinstall on the vehicle at the When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) first opportunity. or for longer than 30 seconds continuously without WARNING! stopping when you are stuck. Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling.
422 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
STARTING AND OPERATING 423 WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
424 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING 425 TIRE CHAINS Use “Class S” chains, or other traction aids that meet SAE Type “S” specifications. Use “Class U” chains on 2500/3500 model trucks, or other traction aids that meet SAE Type “U” specifications. NOTE: Chains must be the proper size for the vehicle as recommended by the chain manufacturer.
426 STARTING AND OPERATING CAUTION! (Continued) • Do not install tire chains on front wheels of 4x2 vehicles. • Do not drive for a prolonged period on dry pavement. • Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed of the chain manufacturer if different than the speed recommended by the manufacturer.
STARTING AND OPERATING 427 CAUTION! Do not use tire chains on the front wheels of any model except for 3500 DRW (Dual Rear Wheel) trucks equipped with LT235/80R17E tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. Do not use tire chains on the rear wheels of 1500 model trucks equipped with LT275/70R17, P275/60R20, or 285/45R22 tires.
428 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 429 Directional Tires – If Equipped Dual Rear Wheels For the R/T package with 22” tires & wheels, tire rotation must be performed with consideration of the tire rotation direction. The recommended rotation pattern for directional tires is shown below. 5 Tire Rotation Tire Rotation The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires.
430 STARTING AND OPERATING CAUTION! 3500 Dual Rear Tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/Off-Road tire and the use of Outline White Letter (OWL) tires. • When replacing a flat, the spare tire may have to be remounted on the rim, or installed at a different location, to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the truck.
STARTING AND OPERATING 431 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure.
432 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING 433 • Seasonal temperature changes will affect tire pressure, The matching full size spare wheel and tire assembly (if and the TPMS will monitor the actual tire pressure in equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The the tire. TPMS will only monitor the pressure in the full size spare Base System when it is used in place of a road tire.
434 STARTING AND OPERATING turn off. The vehicle may need to be driven for up to 3. Accumulation of snow or ice around the wheels or 20 minutes above 15 mph (24 km/h) in order for the wheel housings. TPMS to receive this information. 4. Using tire chains on the vehicle. Check TPMS Warning 5. Using wheels/tires not equipped with TPM sensors. If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid.
STARTING AND OPERATING 435 Premium System – If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module.
436 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The TPM Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display one or more low pressure messages (Left Front, Left Rear, Right Front, Right Rear) for three seconds and a graphic showing the pressure values of each tire with the low tire pressure values flashing.
STARTING AND OPERATING 437 turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime.
438 STARTING AND OPERATING If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the TPM Telltale Light will no longer flash, and the ⬙CHECK TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: Vehicles With Full Size Spare 1.
STARTING AND OPERATING 439 Tire Pressure Monitor System (TPMS) Tire Light Load Inflation Switch Description (2500 Models) – If Equipped WARNING! Never operate your vehicle with the TPMS and tire pressures set to the Light Load Inflation Pressure settings if carrying more than two occupants (150 lbs [68 kg] each) plus 200 lbs (91 kg) of cargo. The vehicle “Light Load Definition” is found in the Supplemental Tire Pressure Information Label which is located on the rear face of the driver door opening.
440 STARTING AND OPERATING load inflation switch LED is ON, the TPMS is using the Tire Light Load Inflation Switch Operation – If light load inflation pressure (cold) low inflation warning Equipped thresholds. • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label.
STARTING AND OPERATING 441 Tire Pressure Information label. The Supplemental Tire Pressure Information label is located on the rear face of the driver door opening. Use an accurate tire gauge to check the tire pressures when lowering all four tire pressures. The vehicle may need to be driven above 15 mph (24 km/h) to receive this updated pressure information. After all four tire pressures have been lowered to the Light Load inflation pressures, press the tire light load inflation switch.
442 STARTING AND OPERATING the rear face of the driver door. Using an accurate tire the max load inflation pressure (cold) values to switch pressure gauge, re-check the tire pressures for the light the TPMS system to the max load inflation pressure load inflation pressure (cold) value. (cold) low pressure warning threshold.
STARTING AND OPERATING 443 • This device may not cause harmful interference. use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these • This device must accept any interference received, engines. including interference that may cause undesired 5.7L Engine operation.
444 STARTING AND OPERATING as hard starting, stalling, and hesitations. If you experi- The manufacturer supports the use of reformulated gasoence these symptoms, try another brand of gasoline lines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine before considering service for the vehicle. and fuel system components.
STARTING AND OPERATING 445 Problems that result from using gasoline containing To fix a Non-FFV vehicle inadvertently fueled once with Methanol or gasoline containing more than 10% Ethanol E-85 perform the following: are not the responsibility of the manufacturer and may • drain the fuel tank (see your authorized dealer) not be covered under warranty.
446 STARTING AND OPERATING of gasoline may not be indicated on the gasoline pump, Fuel System Cautions therefore, you should ask your gasoline retailer whether CAUTION! or not his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, Follow these guidelines to maintain your vehicle’s because MMT can be used at levels higher than those performance: allowed in the United States. MMT is prohibited in • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING 447 CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
448 STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL (4.7L ENGINE ONLY) — IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel vehicles only.
STARTING AND OPERATING 449 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame. Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of E-85 Badge these two.
450 STARTING AND OPERATING • you do not add less than 5 gallons (19 Liters) when Selection Of Engine Oil For Flexible Fuel Vehicles refueling (E-85) And Gasoline Vehicles FFV vehicles operated on E-85 require specially formu• you operate the vehicle immediately after refueling for lated engine oils. These special requirements are included a period of at least 5 minutes in MOPAR威 engine oils, and in equivalent oils meeting Observing these precautions will avoid possible hard Chrysler Specification MS-6395.
STARTING AND OPERATING 451 NOTE: Use of the engine block heater (if equipped) is beneficial for E-85 startability when the ambient temperature is less than 32°F (0°C). CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Cruising Range Because E-85 fuel contains less energy per gallon/liter Maintenance than gasoline, you will experience an increase in fuel consumption.
452 STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap ADDING FUEL The fuel filler cap (gas cap) is located behind the fuel tether in the hook, located on the fuel filler door. filler door, on the left side of the vehicle. Open the fuel CAUTION! door and remove the fuel cap by turning it counterclockwise. • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
STARTING AND OPERATING 453 WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound.
454 STARTING AND OPERATING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture. The bar code that appears on the bottom of the label is your VIN. Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.
STARTING AND OPERATING 455 The entire vehicle should first be weighed on a commerInflation Pressure This is the cold tire inflation pressure for your vehicle for cial scale to insure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle should all loading conditions up to full GAWR. then be determined separately to be sure that the load is Curb Weight properly distributed over the front and rear axle.
456 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING 457 Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. NOTE: The GCWR rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
458 STARTING AND OPERATING that typically provides adjustable friction associated with safety. The addition of a friction/hydraulic sway control the telescoping motion to dampen any unwanted trailer also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. swaying motions while traveling.
STARTING AND OPERATING 459 5 EXAMPLE — Without Weight-Distributing Hitch (Incorrect) EXAMPLE — With Weight-Distributing Hitch (Correct)
460 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. EXAMPLE — Improper Adjustment of WeightDistributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed.
STARTING AND OPERATING 461 Weight Ratings)” for the website address that contains All trailer hitches should be professionally installed on the necessary information for your specific drivetrain. your vehicle. Trailer Hitch Classification Definitions Class Max.
462 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions.
STARTING AND OPERATING 463 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for further information.
464 STARTING AND OPERATING WARNING! WARNING! (Continued) Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision.
STARTING AND OPERATING 465 WARNING! (Continued) 2. GTW 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements – Tires • Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires – General Information” in “Starting and Operating” for the proper inspection procedure.
466 STARTING AND OPERATING actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity.
STARTING AND OPERATING 467 NOTE: This module has been designed and verified for The user interface consists of the following: electric trailer brakes. To determine the type of brakes on GAIN/ Brake Output Power Display your trailer, check with your trailer manufacturer or Shows the current GAIN setting. dealer. This display may also be used to display diagnostic information, if needed.
468 STARTING AND OPERATING lever is activated while the brake is also applied, the GAIN Adjustment Buttons (+/-) greater of the two inputs determines the power sent to Pressing these buttons will adjust the brake control the trailer brakes. power output to the trailer brakes in 0.5 increments. The GAIN setting can be increased to a maximum of 10 or The trailer and the vehicle’s brake lamps will come on decreased to a minimum of 0 (no trailer braking).
STARTING AND OPERATING 469 1. Make sure the trailer brakes are in good working Repeat Steps 5 and 6 until the GAIN setting is at a point condition, functioning normally, and properly adjusted. just below trailer wheel lockup. If towing a heavier See your trailer dealer if necessary. trailer, trailer wheel lockup may not be attainable even with the maximum GAIN setting of 10. 2. Hook up the trailer and make the electrical connections according to the trailer manufacturer’s instructions.
470 STARTING AND OPERATING CAUTION! The ITBM module has been designed and verified for electric trailer brakes. Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in damage to your vehicle, trailer, or other property. WARNING! The ITBM module has been designed and verified for electric trailer brakes.
STARTING AND OPERATING 471 NOTE: Do not cut or splice wiring into the vehicle’s wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
472 STARTING AND OPERATING WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automotive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic.
STARTING AND OPERATING 473 NOTE: Using “TOW/HAUL” mode or a lower gear Electronic Speed Control – If Equipped range while operating the vehicle under heavy operating − Do not use in hilly terrain or with heavy loads. conditions will improve performance and extend transmission life by reducing excessive shifting and heat build − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until up. This action will also provide better engine braking.
474 STARTING AND OPERATING − Air Conditioning Turn off temporarily. CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. SNOWPLOW 1500 Models Only NOTE: Do not use this model vehicle for snowplow applications. WARNING! Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
STARTING AND OPERATING 475 Builders Guide. See your authorized dealer, installer or Before Plowing snowplow manufacturer for this information. There are • Check the hydraulic system for leaks and proper fluid unique electrical systems that must be connected to level. properly assure operator safety and prevent overloading • Check the mounting bolts and nuts for proper tightvehicle systems. ness.
476 STARTING AND OPERATING 2. The total GVWR or the Front GAWR or the Rear if necessary at the beginning and end of the snowplow GAWR should never be exceeded. season. This will help prevent uneven tire wear. 3. Cargo capacity will be reduced by the addition of The blade should be lowered whenever the vehicle is options or passengers, etc. parked.
STARTING AND OPERATING 477 Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility. NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient temperature.
478 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 479 6. Install a suitable clamping device, designed for towRecreational Towing – Two-Wheel Drive Models DO NOT flat tow this vehicle. Damage to the drivetrain ing, to secure the front wheels in the straight position. will result. Recreational towing (for two-wheel drive models) is allowed ONLY if the rear wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1.
480 STARTING AND OPERATING must be placed in gear (NOT in NEUTRAL) for recreational towing. Refer to the following for the proper transfer case NEUTRAL shifting procedure for your vehicle. CAUTION! • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. • Tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case.
STARTING AND OPERATING 481 Shifting Into Neutral (N) – Manual Shift Transfer Case (If Equipped) Use the following procedure to prepare your vehicle for recreational towing. CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in Neutral (N) before recreational towing to prevent damage to internal parts.
482 STARTING AND OPERATING 8. Release the brake pedal (and clutch pedal on manual 13. Remove the key fob from the ignition switch. transmissions) for five seconds and ensure that there is 14. Attach the vehicle to the tow vehicle using a suitable no vehicle movement. tow bar. 9. Repeat steps 7 and 8 with automatic transmission in 15. Release the parking brake. DRIVE or manual transmission in first gear. Shifting Out Of Neutral (N) – Manual Shift 10. Turn OFF the engine.
STARTING AND OPERATING 483 6. Shift the transfer case lever to the desired position. Shifting Into Neutral – Electronic Shift Transfer Case (If Equipped) NOTE: When shifting out of transfer case Neutral (N), Use the following procedure to prepare your vehicle for turning the engine OFF may be required to avoid gear recreational towing: clash. 7. Shift the automatic transmission into PARK, or place manual transmission in Neutral. 8. Release the brake pedal. 9. Disconnect vehicle from the tow vehicle. 10.
484 STARTING AND OPERATING CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing to prevent damage to internal parts. light will blink while the shift is in progress. The light will stop blinking (stay on solid) when the shift to NEUTRAL is complete. 7. After the shift is completed and the NEUTRAL light stays on, release the NEUTRAL button. 1. Bring the vehicle to a complete stop. Shift automatic 8. Start the engine.
STARTING AND OPERATING 485 14. Shift the transmission into PARK or place manual • Steps 1 through 5 are requirements that must be met transmission in gear (not in Neutral). prior to pressing the NEUTRAL button, and must continue to be met until the shift has been completed.
486 STARTING AND OPERATING Shifting Out Of Neutral – Electronic Shift Transfer 8. After the NEUTRAL button has been released, the transfer case will shift to the position identified by the Case (If Equipped) Use the following procedure to prepare your vehicle for selector switch. normal usage: NOTE: When shifting out of transfer case NEUTRAL, 1. Bring the vehicle to a complete stop, leaving it con- turning the engine OFF may be required to avoid gear nected to the tow vehicle. clash. 2.
STARTING AND OPERATING 487 15. Shift the transmission into gear, release the brake • The ignition switch must be in the ON/RUN position pedal (and clutch pedal on manual transmissions), and for a transfer case shift to take place and for the check that the vehicle operates normally. position indicator lights to be operable.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 491 䡵 Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 491 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 510 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 492 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 510 ▫ Removing The Spare Tire . . . . . . . . . . . . . . .
490 WHAT TO DO IN EMERGENCIES 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 518 ▫ Two-Wheel Drive Models . . . . . . . . . . . . . . 520 ▫ Towing Without The Ignition Key FOB . . . . . 519 ▫ Four-Wheel Drive Vehicles . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 491 HAZARD WARNING FLASHERS JACKING AND TIRE CHANGING The Hazard Warning flasher switch is located on the WARNING! upper switch bank just below the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flashers.
492 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack and jack tools are stored under the front passenger seat.
WHAT TO DO IN EMERGENCIES 493 6 Jack And Tools (1500 Series) Jack And Tools (2500/3500 Series)
494 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Reinstalling The Jack And Tools (1500 Series) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. Turn Screw And Lug 2.
WHAT TO DO IN EMERGENCIES 495 6 Folding Flap And Rolling Bag Tying Bag To Jack With Straps
496 WHAT TO DO IN EMERGENCIES Jack And Tools Tied 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt. Reinstall the plastic cover.
WHAT TO DO IN EMERGENCIES 497 enough cable slack to allow you to pull it out from under the vehicle. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel. NOTE: Always stow the spare tire with the valve stem facing the ground. 6 Jack And Tools (2500/3500 Series) Removing The Spare Tire Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube.
498 WHAT TO DO IN EMERGENCIES It is recommended that you stow the flat or spare to 3. Set the parking brake. avoid tangling the loose cable. 4. Place the shift lever into PARK. On four-wheel drive NOTE: The winch mechanism is designed for use with vehicles, shift the transfer case to the 4L position. the jack extension tube only. Use of an air wrench or other 5. Turn the ignition OFF. power tools is not recommended and can damage the winch. 6.
WHAT TO DO IN EMERGENCIES 499 Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
500 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3.
WHAT TO DO IN EMERGENCIES 501 drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the drive tubes extending to the rear. 6 4X4 Jacking Location Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required. Rear Jacking Location For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench.
502 WHAT TO DO IN EMERGENCIES CAUTION! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. • 2500/3500 Series Trucks For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. 4x2 Jacking Location Operate the jack using the jack drive tube and the wheel wrench.
WHAT TO DO IN EMERGENCIES 503 jack under the axle as close to the tire as possible with the drive tube to the extension tube. Place the jack under the drive tubes extending to the front. Connect the jack tube axle between the spring and the shock absorber with the drive tubes extending to the rear. extension and wheel wrench. 6 4x4 Jacking Location Rear Jacking Location (All) For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench.
504 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. On single rear-wheel (SRW) trucks, install the spare wheel Before raising the wheel off the ground, make sure and wheel nuts with the cone shaped end of the wheel that the jack will not damage surrounding truck parts nuts toward the wheel. On 3500 dual rear-wheel models (DRW) the wheel nuts are a two-piece assembly with a and adjust the jack position as required. flat face. Lightly tighten the wheel nuts.
WHAT TO DO IN EMERGENCIES 505 WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. Hub Caps/Wheel Covers — If Equipped The hub caps must be removed before raising the vehicle off the ground. For 2500/3500 single rear-wheel (SRW) models, use the blade on the end of the lug wrench to pry the hub cap off.
506 WHAT TO DO IN EMERGENCIES CAUTION! • Use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. • The rear hub caps on the dual rear wheel has two pry-off notches. Make sure that the hook of the jack handle driver is located squarely in the cap notch before attempting to pull off. You must use the flat end of the lug wrench to pry off the wheel skins.
WHAT TO DO IN EMERGENCIES 507 Disc Wheels Type Nut Stud Size Torque Ft. Lbs. Cone 9/16-18 120-150 Torque Newton Meters 160-200 Flanged 9/16-18 130-160 190-220 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer.
508 WHAT TO DO IN EMERGENCIES Dual wheel models require a special heavy-duty lug nut These dual rear wheels should be tightened as follows: tightening adapter (included with the vehicle) to correctly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. NOTE: When installing a spare tire as part of a dual rear wheel end combination, the tire diameter of the two individual tires must be compared.
WHAT TO DO IN EMERGENCIES 509 second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times. Torque wheel stud nuts to specifications at each lubrication interval. WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately.
510 WHAT TO DO IN EMERGENCIES HOISTING NOTE: When using a portable battery booster pack A conventional floor jack may be used at the jacking follow the manufacturer’s operating instructions and locations. Refer to the graphics that show jacking loca- precautions. tions. However, a floor jack or frame hoist must never be CAUTION! used on any other parts of the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result.
WHAT TO DO IN EMERGENCIES 511 NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Positive Battery Post WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured.
512 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 513 WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle.
514 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If the vehicle becomes stuck in snow, sand or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between DRIVE and REVERSE while applying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
WHAT TO DO IN EMERGENCIES 515 WARNING! WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. • Chains are not recommended for freeing a stuck vehicle.
516 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use one of the following procedures to temporarily move the shift lever: Column Shifter — If Equipped 1. Firmly set the parking brake. 2. Turn the ignition switch to the ON/RUN position without starting the engine. 3. Tilt the steering wheel to the full up position 4. Press and maintain firm pressure on the brake pedal. Shift Lever Override Access Port 5.
WHAT TO DO IN EMERGENCIES 517 Center Console Shifter — If Equipped To access the override, carefully remove (using a flatbladed screwdriver) the override access cover which is located on the right of the shift lever gate. 1. Firmly set the parking brake. 2. Turn the ignition switch to the ON/RUN position without starting the engine. 3. Press and maintain firm pressure on the brake pedal. 4. Using a screwdriver or similar tool, press and hold the override tab through the access port on the center console.
518 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the transmission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational Towing” in the “Starting and Operating” section.
WHAT TO DO IN EMERGENCIES 519 Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws applying to vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
520 WHAT TO DO IN EMERGENCIES Two-Wheel Drive Models 15 miles (24 km), tow with the rear wheels OFF the The manufacturer recommends towing your vehicle with ground. Acceptable methods are to tow the vehicle on a all four wheels OFF the ground using a flatbed. flatbed, or with the rear wheels raised using a wheel lift or towing dolly.
WHAT TO DO IN EMERGENCIES 521 CAUTION! • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • Failure to follow these towing methods could result in damage to the transmission and/or transfer case. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.7L . . . . . . . . . . . . . 526 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 532 䡵 Engine Compartment — 4.7L . . . . . . . . . . . . . 527 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 533 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 528 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 535 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 529 ▫ Engine Air Cleaner Filter . . . . . . . . .
524 MAINTAINING YOUR VEHICLE ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . 540 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 570 ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 540 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 571 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 541 ▫ Dual Or Quad Headlamp/Front Park And Turn Signal — If Equipped . . . . . . . . . . . . . 571 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 525 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . 582 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 583 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . .
526 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 527 ENGINE COMPARTMENT — 4.
528 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.
MAINTAINING YOUR VEHICLE 529 ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
530 MAINTAINING YOUR VEHICLE the SELECT button to turn off the message. If the Normally, the OBD II system will be ready. The OBD II problem continues, the message will appear the next time system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacethe vehicle is started. ment. If the OBD II system should be determined not A loose, improperly installed, or damaged fuel filler cap ready for the I/M test, your vehicle may fail the test.
MAINTAINING YOUR VEHICLE 531 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a. The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
532 MAINTAINING YOUR VEHICLE your vehicle. Refer to these Service Manuals before MAINTENANCE PROCEDURES The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle. systems may void your warranty and could result in civil Besides those maintenance items specified in the fixed penalties being assessed against you.
MAINTAINING YOUR VEHICLE 533 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
534 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 535 Lubricants which do not have both the engine oil certi- Disposing Of Used Engine Oil And Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, ber should not be used. indiscriminately discarded, can present a problem to the NOTE: For 2500/3500 trucks with a 5.7L engine operenvironment.
536 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter used to assure most efficient service. MOPAR威 engine air Refer to the “Maintenance Schedule” for the proper cleaner filters are a high quality filter and are maintenance intervals. recommended. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
MAINTAINING YOUR VEHICLE 537 WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. • Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling.
538 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
MAINTAINING YOUR VEHICLE 539 tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR威 Spray White Lube or equivalent, to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit. After lubricating, excess oil and grease should be removed.
540 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Adding Washer Fluid The fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not radiator antifreeze).
MAINTAINING YOUR VEHICLE 541 If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; Commercially available windshield washer solvents or when the underside or rear of the vehicle is damaged; are flammable. They could ignite and burn you. Care have an authorized technician inspect the complete exmust be exercised when filling or working around haust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
542 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE 543 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
544 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE 545 Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Use only the manufacturer’s recommended engine coolant (antifreeze). Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
546 MAINTAINING YOUR VEHICLE Adding Coolant • Mix a minimum solution of 50% HOAT engine coolant Your vehicle has been built with an improved engine and distilled water. Use higher concentrations (not to coolant (antifreeze) that allows extended maintenance exceed 70%) if temperatures below ⫺34°F (⫺37°C) are intervals. This engine coolant (antifreeze) can be used up anticipated. to five years or 104,000 miles (169 000 km) before • Use only high purity water such as distilled or deionreplacement.
MAINTAINING YOUR VEHICLE 547 Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that the engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution.
548 MAINTAINING YOUR VEHICLE rules for your community. To prevent ingestion by animals or children do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Checking Coolant Level – 3.7L, 4.7L, and 5.7L Engines With the engine OFF and cold, the level of the engine coolant should be between the MIN and MAX range on the dipstick.
MAINTAINING YOUR VEHICLE 549 of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
550 MAINTAINING YOUR VEHICLE • Do not overfill the coolant recovery bottle. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the • Check engine coolant (antifreeze) freeze point in the condenser clean, also. radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of • Do not change the thermostat for Summer or Winter operation.
MAINTAINING YOUR VEHICLE 551 WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot.
552 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE 553 WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Rear Axle And 4x4 Front Driving Axle Fluid Level For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.
554 MAINTAINING YOUR VEHICLE Limited-Slip Differentials This vehicle requires that 4 oz. (118 ml) MOPAR威 Limited Slip Additive or equivalent be added to the gear lubricant. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. The MOPAR威 Limited Slip Additive or equivalent should be added to the gear lubricant whenever a fluid change is made. Fluid Level Check This fluid level can be checked by removing the filler plug.
MAINTAINING YOUR VEHICLE 555 CAUTION! • Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes.
556 MAINTAINING YOUR VEHICLE 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. Verify that solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do not overfill.
MAINTAINING YOUR VEHICLE 557 CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. NOTE: If the transmission is disassembled for any reason, the fluid and filter(s) should be changed. It is important that proper lubricant is used in the transmission.
558 MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your veresistance built into your vehicle. hicle in the shade using MOPAR威 Car Wash or equivaWhat Causes Corrosion? lent, or a mild car wash soap and rinse the panels Corrosion is the result of deterioration or removal of completely with clear water. paint and protective coatings from your vehicle.
MAINTAINING YOUR VEHICLE 559 CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
560 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner.
MAINTAINING YOUR VEHICLE 561 MOPAR威 Total Clean or equivalent is specifically recom- Cleaning Headlights Your vehicle is equipped with plastic headlights and fog mended for leather upholstery. lights (if equipped) that are lighter and less susceptible to Your leather upholstery can be best preserved by regular stone breakage than glass headlights. cleaning with a damp soft cloth.
562 MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
MAINTAINING YOUR VEHICLE 563 To help maintain the appearance of your Spray-On Bedliner, the manufacturer recommends you periodically rinse all loose dirt from your truck bed and clean your truck at least twice per year using the MOPAR威 Spray-On Bedliner Conditioner available at your local authorized dealer. WARNING! Do not use silicon-based protection products to clean your bedliner. Silicon-based products can become slippery and may result in personal injury.
564 MAINTAINING YOUR VEHICLE to cover the metal exposed by the scratch is required. To repair a tear or gouge, follow the directions provided in the MOPAR威 Quick Repair Kit. FUSES Totally Integrated Power Module The Totally Integrated Power Module is located in the engine compartment near the battery. This center contains cartridge fuses and mini fuses.
MAINTAINING YOUR VEHICLE 565 Cavity J03 J04 J05 J06 J07 J08 J11 Cartridge Fuse 30 Amp Pink 25 Amp Natural 25 Amp Natural 40 Amp Green 30 Amp Pink 40 Amp Green 30 Amp Pink Mini Fuse Description Cavity Diesel Powertrain Control Module – If Equipped Driver Door Node J13 J14 J15 Passenger Door Node Antilock Brakes Pump/Stability Control System Antilock Brakes Valve/Stability Control System Power Seat Drivetrain Control Module J17 J18 Cartridge Fuse 60 Amp Yellow 20 Amp Blue 30 Amp Pink 40 Amp Green
566 MAINTAINING YOUR VEHICLE Cavity J21 J22 M1 M5 M6 M7 M8 M9 Cartridge Fuse 20 Amp Blue 25 Amp Natural Mini Fuse 15 Amp Blue 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Cavity Front Washer Control Sunroof Module M10 Stop Switch Lamp 115V AC Inverter Power Outlet #1 (Cigar Lighter)/ Rain Snsr Power Outlet #2 Front Heated Seat & Steering Wheel Rear Heated Seats M11 M12 M13 Cartridge Fuse Mini Fuse 20 Amp Yellow 10 Amp Red 30 Amp Green 20 Amp Yellow Descri
MAINTAINING YOUR VEHICLE 567 Cavity M14 M15 M16 M19 M20 Cartridge Fuse Mini Fuse 20 Amp Yellow 20 Amp Yellow 10 Amp Red 25 Amp Natural 15 Amp Blue Description Cavity Back Up Camera (Domestic Only) Power Seat Module(s)/Audio Telematics/Daytime Running Lights Relay/Instrument Cluster/Transfer Case Module Airbag Module M21 Automatic Shutdown 1 and 2 Instrument Cluster Interior Lighting /Sw Steering Wheel/Sw Bank M22 M23 M25 M26 M27 M28 M29 Cartridge Fuse Mini Fuse 20 Amp Yellow 10 Amp Red 10 Amp
568 MAINTAINING YOUR VEHICLE Cavity M30 M32 M33 M34 M35 M36 Cartridge Fuse Mini Fuse 15 Amp Blue 10 Amp Red 10 Amp Red 10 Amp Red 15 Amp Blue 20 Amp Yellow Description Cavity J1962 Diag Connector Airbag Module M37 Powertrain Control Module Park Assist Module/Climate Control System Module/IR Sensor/ Compass Module Left Front & Rear Parklamps Power Outlet M38 Cartridge Fuse Mini Fuse 10 Amp Red 25 Amp Natural Description Antilock Brakes/ Stability Control System Module/ Stoplamp Switch All Door
MAINTAINING YOUR VEHICLE 569 CAUTION! (Continued) • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected. • As an alternative to the above steps you may disconnect the negative cables from both batteries.
570 MAINTAINING YOUR VEHICLE (or check to see if the fuse is blown) to ensure that it is fully seated. When the IOD fuse is extracted, the instrument cluster in the odometer window will display ⬙NO FUSE.” REPLACEMENT BULBS LIGHT BULBS – Interior Bulb No. Overhead Console Lamps . . . . . . . . . . . . . . . TS 212-2 Dome Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 NOTE: For lighted switches, see your authorized dealer for replacement instructions.
MAINTAINING YOUR VEHICLE 571 BULB REPLACEMENT Dual Or Quad Headlamp/Front Park And Turn Signal — If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two plastic push-in rivets that secure the upper radiator seal to the radiator. 7.
572 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect the wiring harness connectors from the splash shield and lift the slide lock upward far enough to bulb socket. disengage it from the lock post on the back of the front 11. Replace bulb(s) as necessary. lamp unit housing. CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE 573 Fog Lamps Rear Tail/Stop, Turn Signal And Backup Lamps 1. Reach under and behind the front bumper to access 1. Remove the two screws that pass through the bed the back of the front fog lamp housing. sheetmetal. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise 1⁄4 turn to unlock the bulb from the housing. 4. Pull the bulb straight out from the housing.
574 MAINTAINING YOUR VEHICLE 2. Pull the outboard side of the lamp rearward far 3. Disconnect the wiring harness connectors from the enough to unsnap the two receptacles on the outboard bulb socket. side of the lamp housing from the two plastic snap post 4. Rotate the bulb socket counterclockwise 1/4 turn to retainers in the outer box side panel. unlock it from the housing. 5. Pull the bulb straight out of the socket.
MAINTAINING YOUR VEHICLE 575 Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 2. Separate the connector holding the housing and wiring harness to the body. 1. Remove the two screws holding the housing/lens to the body as shown. 7 3. Turn the desired bulb socket ⁄ turn and remove the socket and bulb from housing.
576 MAINTAINING YOUR VEHICLE 4. Pull the desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing. Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE 577 2. Rotate the socket 1⁄4 turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
578 MAINTAINING YOUR VEHICLE Rear Lamp Bar ID Marker (Dual Rear Wheels) — If 2. Turn the socket 1⁄4 turn counterclockwise to access the Equipped bulb. 1. Loosen the two screws and the housing to gain access 3. Pull the bulb straight out from the socket. to the bulb sockets. 4. Reverse the procedure for installation of the bulbs and housing.
MAINTAINING YOUR VEHICLE 579 Side Marker Lamps (Dual Rear Wheels) — If Equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket 1⁄4 turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the procedure for installation of the bulbs and housing.
580 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 1500 Regular Cab Longbed/Crew Quad Cab Models (Optional) 2500/3500 Shortbed Models 2500/3500 Longbed Models Engine Oil with Filter 3.7L Engine (SAE 5W-20, API Certified) 4.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-30, API Certified). For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs (6 350 kg).
MAINTAINING YOUR VEHICLE 581 Cooling System 3.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 4.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7L Engine — 1500 Models (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7L Engine — 2500/3500 Models (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.
582 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil – For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs/(6,350 kg.) Engine Oil Filter Spark Plugs – 3.7L Engine Spark Plugs – 4.7L Engine Spark Plugs – 5.7L Engine Fuel Selection – 3.7L and 4.7L Engines Fuel Selection – 5.
MAINTAINING YOUR VEHICLE 583 Chassis Component Automatic Transmission Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. Transfer Case MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. Transfer Case – BW44–44 Only MOPAR威 BW44–44 Transfer Case Fluid or equivalent. Front Axle – 1500 Four-Wheel Drive GL-5 SAE 75W-90 (MS-9763) or equivalent.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 588 E MAINTENANCE SCHEDULES CONTENTS 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 586 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done S anytime a malfunction is suspected.
MAINTENANCE SCHEDULES 587 M Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change.
M 588 MAINTENANCE SCHEDULES A I CAUTION! N T Failure to perform the required maintenance items E N may result in damage to the vehicle. A N Required Maintenance Intervals C E NOTE: ** Vehicles built with the 4.7L engine are S equipped with sixteen spark plugs. One set is located on C the top of the engine under the coils and the second set is H located on the side of the engine. E D U L E S 8 The spark plugs located under the coils are a standard plug and must be changed every 48,000 miles (78 000 km).
MAINTENANCE SCHEDULES 589 M 8,000 Miles (13,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only).
M 590 MAINTENANCE SCHEDULES A I 24,000 Miles (39,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 24,000 miles (39 000 km). S C H E D U L E S 8 ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 591 M 40,000 Miles (65,000 km) or 30 Months Maintenance Service Schedule 48,000 Miles (78,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only).
M 592 MAINTENANCE SCHEDULES A I 56,000 Miles (91,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 56,000 miles (91 000 km). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only).
MAINTENANCE SCHEDULES 593 M 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). Replace the engine air cleaner filter. Replace the ignition cables (3.7L Engine). Replace the spark plugs (3.7L and 5.7L Engines). Lube the front drive shaft fitting (2500/3500 (4x4) models only).
M 594 MAINTENANCE SCHEDULES A I 72,000 Miles (117,000 km) or N T 54 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 72,000 miles (117 000 km). S C H E D U L E S 8 ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 595 M 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only).
M 596 MAINTENANCE SCHEDULES A I 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). E ❏ Replace the engine air cleaner filter. N ❏ Replace the ignition cables (4.7L Engine). A ❏ Replace the top row and side row of spark plugs (4.7L Engine).** N ❏ Replace the spark plugs (3.7L and 5.7L Engines).
MAINTENANCE SCHEDULES 597 M 104,000 Miles (169,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Flush and replace the engine coolant at 104,000 miles (169 000 km) or 60 months whichever comes first.
M 598 MAINTENANCE SCHEDULES A I 120,000 Miles (195,000 km) or 90 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). A N ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 599 M 128,000 Miles (208,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ Replace the engine air cleaner filter. ❏ Replace the ignition cables (3.7L Engine). ❏ Replace the spark plugs (3.7L and 5.7L Engines). ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only).
M 600 MAINTENANCE SCHEDULES A I 144,000 Miles (234,000 km) or 108 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). A N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the C engine air cleaner filter; replace if necessary. E ❏ Replace the top row of spark plugs (4.7L Engine).
MAINTENANCE SCHEDULES 601 M † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 607 ▫ Prepare For The Appointment . . . . . . . . . . . 605 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 607 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 605 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
604 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 611 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 611 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 611 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 605 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
606 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (866) 726–4636 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE 607 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
608 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 609 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.
610 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC vemaintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency LLC vehicles.
IF YOU NEED CONSUMER ASSISTANCE 611 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
612 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
614 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . 546 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 452 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 133 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 536 Air Conditioner Maintenance . . . . . . . . . . . . . . . 538 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 291 Air Conditioning Controls . . . . . . . . . . . . . . . . . 291 Air Conditioning Refrigerant . . . . . . . . . . .
INDEX 615 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 396 Brake Control System, Electronic . . . . . . . . . . . . . 395 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 551,583 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 394,550 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . 395 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . 551 Master Cylinder . . . . . . . . . . . . . . . . . . . . . 551 Parking . . . . . . . . . . . . . . . . . .
616 INDEX Caps, Filler Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . 534 Power Steering . . . . . . . . . . . . . . . . . . . . . . 391 Radiator (Coolant Pressure) . . . . . . . . . . . . . 547 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558 Carbon Monoxide Warning . . . . . . . . . . . . . . . 82,447 Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . .
INDEX 617 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 180 Defroster, Windshield . . . . . . . . . . . . . . . . 84,293,299 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . 130 Differential, Limited-Slip . . . . . . . . . . . . . . . . . . 365 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . 556 Power Steering . . . . . . . . . . . . . . . . . . . . . . 391 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 518 Disposal Antifreeze (Engine Coolant) . .
618 INDEX Dual Rear Wheels . . . . . . . . . . . . . . . . . . . . . 429,507 Emergency, In Case of DVD Player (Video Entertainment System™) . . . . 286 Freeing Vehicle When Stuck . . . . . . . . . . . . . 514 Hazard Warning Flasher . . . . . . . . . . . . . . . 491 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . 510 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448 Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . 515 Electric Rear Window Defrost . . . . . . . .
INDEX 619 Oil Selection . . . . . . . . . . . . . . . . . . . . . 534,580 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . 535 Temperature Gauge . . . . . . . . . . . . . . . . . . . 210 Enhanced Accident Response Feature . . . . . . . . . . 63 Entry System, Illuminated . . . . . . . . . . . . . . . . . . 19 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 66 Exhaust Gas Caution . . . . . . . . . . . . . .
620 INDEX Four-Way Hazard Flasher . . . . . . . . . . . . . . . . . . 491 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . 514 Front Axle (Differential) . . . . . . . . . . . . . . . . . . . 553 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . 452 Conserving . . . . . . . . . . . . . . . . . . . . . . 235,237 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 Filler Cap (Gas Cap) . . . . . . .
INDEX 621 Gross Axle Weight Rating . . . . . . . . . . . . . . . . . . 457 Gross Vehicle Weight Rating . . . . . . . . . . . . . . . . 456 Guide, Body Builders . . . . . . . . . . . . . . . . . . . . . . 6 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 Hands-Free Phone (Uconnect™) . . . . . . . . . . . . Hazard Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . Hazard Warning Flasher . . . . . . . . . . . . . . . . . .
622 INDEX Information Center, Vehicle . . . . . . . . . . . . . . . . . 227 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 93 Instrument Cluster . . . . . . . . . . . . . . . . . 206,208,210 Instrument Panel and Controls . . . . . . . . . . . . . . 205 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 562 Integrated Power Module (Fuses) . . . . . . . . . . . . 564 Integrated Trailer Brake Controls . . . . . . . . . . . . . 466 Interior Appearance Care . . . . . . . . . . . . . . . .
INDEX 623 Instrument Cluster . . . . . . . . . . . . . . . . . 206,210 Brake Assist Warning . . . . . . . . . . . . . . . . . . 403 Interior . . . . . . . . . . . . . . . . . . . . . . . . . 125,150 Brake Warning . . . . . . . . . . . . . . . . . . . . . . 219 Lights On Reminder . . . . . . . . . . . . . . . . . . 127 Bulb Replacement . . . . . . . . . . . . . . . . . 570,571 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Cap Top Clearance . . . . . . . . . . . . . . . . . . .
624 INDEX Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Automatic Door . . . . . . . . . . . . . . . . . . . . . . 30 Child Protection . . . . . . . . . . . . . . . . . . . . . . 33 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . 30 Low Tire Pressure System . . . . . . . . . . . . . . . . . .
INDEX 625 Navigation System (Uconnect™ gps) . . . . . . . . . . 147 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 81 Identification Logo . . . . . . . . . . . . . . . . . . . 534 Materials Added to . . . . . . . . . . . . . . . . . . . 535 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . 214 Recommendation . . . . . . . . . . . . . . . . . . 534,580 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . 535 Viscosity . . . . . . . . . . . . . . . . . . . . . . . .
626 INDEX Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Pedals, Adjustable . . . . . . . . . . . . . . . . . . . . . . . 133 Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 242 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 81 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 627 Reclining Rear Seats . . . . . . . . . . . . . . . . . . . . . . 110 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 66 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 478 Shifting into Transfer Case Neutral(N) . . . 481,483 Shifting out of Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . . . . . 482,486 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 444 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . .
628 INDEX Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . 50 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . 226 Untwisting Procedure . . . . . . . . . . . . . . . . . . 47 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101,110 Adjustment . . . . . . . . . . . . . .
INDEX 629 Sliding Rear Window Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 425 Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 419,420 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582 Speed Control (Cruise Control) . . . . . . . . . . . . . .
630 INDEX Tip Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Tire and Loading Information Placard . . . . . . 411,424 Tire Identification Number (TIN) . . . . . . . . . . . . . 409 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 406 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85,415,611 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . 422 Air Pressure . . . . . . . . . . .
INDEX 631 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 456 Cooling System Tips . . . . . . . . . . . . . . . . . . 473 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 Minimum Requirements . . . . . . . . . . . . . . . . 463 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Trailer and Tongue Weight . . . . . . . . . . . . . . 462 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470 Trailer Towing Guide . . . . . . . . . . . . . . . .
632 INDEX Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 412,453 Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . 506 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7 Winch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 374 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 301,569 Operation . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler Group LLC 12D241-226-AG Seventh Edition Printed in U.S.A.
