Chassis cab 3500/4500/5500 USER GUIDE 2011 889284_11f_Ram_Chassis_Cab_UserGuide_030111.
If you are the first registered owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/Media Center Manuals or Warranty Booklet by calling 1-866-726-4636 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer. The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury.
TABLE OF CONTENTS INTRODUCTION/WELCOME OFF-ROAD CAPABILITIES Welcome From Chrysler Group LLC . . . 2 Four-Wheel Drive Operation . . . . . . 46 CONTROLS AT A GLANCE UTILITY Driver Cockpit . . . . . . . . . . . . . . . 4 Instrument Cluster . . . . . . . . . . . . 6 Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . 47 Integrated Trailer Brake Module . . . . 47 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . 47 Auxiliary Switches . . . . . . . . . . .
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place.
INTRODUCTION/WELCOME Vehicles Sold In Canada With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. WARNING! • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving.
CONTROLS AT A GLANCE DRIVER COCKPIT 4
CONTROLS AT A GLANCE 5
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Airbag Warning Light** - Electronic Throttle Control (ETC) Light - Engine Temperature Warning Light - Transmission Temperature Warning Light - Seat Belt Reminder Light BRAKE - Brake Warning Light** - Malfunction Indicator Light (MIL)** - SERV (Service) 4WD Indicator Light (See page 50 for more information.
CONTROLS AT A GLANCE Indicators - Cargo Lamp On Indicator - Turn Signal Indicators - High Beam Indicator - Front Fog Light Indicator - Vehicle Security Indicator* - Four-Wheel Drive and 4LOCK Mode Indicator - Exhaust Brake Indicator (Diesel Only) - Door Ajar Indicator - TOW/HAUL Indicator - Electronic Speed Control On Indicator - Four-Wheel Drive LOW Mode Indicator - Loose Gas Cap Indicator Odometer Messages LoWASH - Low Washer Fluid noFUSE* - Fuse Fault CHAngE OIL* - Change Engine Oil Water in Fuel
GETTING STARTED KEY FOB Locking And Unlocking The Doors • Press the LOCK button once to lock all the doors. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors. • All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide. Panic Alarm • Press the PANIC button once to turn the panic alarm on.
GETTING STARTED CAUTION! (Continued) • Charge the battery. • Contact your dealer for assistance on how to remove the Key Fob using the manual over ride method. WARNING! • Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the Key Fob inside the vehicle or in the ignition.
GETTING STARTED THEFT ALARM To Arm • Press the Key Fob LOCK button or the power door lock switch while the door is open. To Disarm • Press the Key Fob UNLOCK button and turn the ignition to the ON/RUN position. SEAT BELT • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt.
GETTING STARTED SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIRBAGS • This vehicle has Advanced Front Airbags for both the driver and right front passenger as a supplement to the seat belt restraint system. The Advanced Front Airbags will not deploy in every type of collision. • Advanced Front Airbags are designed to provide additional protection by supplementing the seat belts in certain frontal collisions depending on the severity and type of collision.
GETTING STARTED Installing The LATCH - Compatible Child Restraint System • Your vehicle’s second row passenger seats are equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the rear seat outboard positions. • LATCH equipped seating positions have both lower anchor bars, located at the back of the seat cushion, and tether strap anchorages, located behind the seat back.
GETTING STARTED Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt) Crew Cab - Rear Seats: • Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position. Remove the elastic before use.
GETTING STARTED NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! • In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed.
GETTING STARTED Memory Seats • The memory seat feature allows you to save the driver's seat position (excluding lumbar position), driver's outside mirror position, adjustable brake and accelerator pedals, Automatic Temperature Control (ATC) temperature setting and radio station preset settings. The driver's memory buttons are located on the outboard side of the driver's seat cushion. • Adjust all memory profile settings, press the SET button, then press 1 or 2 within five seconds.
GETTING STARTED CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked.
GETTING STARTED Front Ventilated Seats • Small fans that draw the air from around the occupant and exhaust it underneath the seat and into the passenger compartment are located in the seat cushion and seatback. The fans draw this air across the surface of the seat using air ducts and fine perforations in the covering to help keep the driver cooler in higher ambient temperatures. • The ventilated seat switches are located in the center instrument panel below the climate controls.
GETTING STARTED HEATED STEERING WHEEL • The steering wheel contains a heating element that heats the steering wheel to one temperature setting. • The heated steering wheel switch is located on the center instrument panel below the climate controls. • Press the switch once to turn the heating element On. Press the switch a second time to turn the heating element Off. • Once the heated steering wheel has been turned on, it will operate for approximately 58 to 70 minutes before automatically shutting off.
GETTING STARTED CAUTION! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal's path. WARNING! • Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have a collision. Adjust the column only while the vehicle is stopped.
GETTING STARTED Cold Start Procedure • Turn the ignition switch to the ON position. If the Wait To Start appears in the cluster, wait for the light to turn off before starting. light • In extremely cold weather below 0°F (-18°C) it may be beneficial to cycle the manifold heaters twice before attempting to start the engine. This can be accomplished by turning the ignition OFF for at least five seconds and then back ON after the “Wait To Start Light” has turned off, but before the engine is started.
OPERATING YOUR VEHICLE TURN SIGNALS/WIPER/WASHER/HIGH BEAMS LEVER Turn Signals/Lane Change Assist • Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off. Wipers Intermittent, Low And High Operation • Rotate the end of the lever to the first detent position for one of five intermittent settings, the second detent for low wiper operation and the third detent for high wiper operation.
OPERATING YOUR VEHICLE HEADLIGHT SWITCH Automatic Headlights/Parking Lights/Headlights • Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent and to the for parking lights . second detent for headlights • With the parking lights or low beam headlights on, push the headlight switch once for fog lights. • Rotate the headlight switch to “A” for AUTO headlights.
OPERATING YOUR VEHICLE SPEED CONTROL LEVER Cruise ON/OFF • Push the ON/OFF button to activate the Speed Control. or CRUISE • The cruise symbol will appear on the instrument cluster to indicate the Speed Control is on. • Push the ON/OFF button a second time to turn the system off. Set • With Speed Control on, push down and release the lever to set a desired speed. Accel/Decel • Push and hold the lever up to accelerate or down to decelerate the vehicle; release the lever to save the new set speed.
OPERATING YOUR VEHICLE WARNING! (Continued) • Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. A collision could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.
OPERATING YOUR VEHICLE AUTOMATIC TEMPERATURE CONTROL (ATC) • Rotate both the Mode Control and Blower Control to the AUTO position. • Select the desired temperature by pushing the up or down temperature buttons for the driver or passenger. • The system will maintain the set temperature automatically. Air Conditioning (A/C) • If the A/C button is pushed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically.
OPERATING YOUR VEHICLE DIESEL EXHAUST BRAKE (ENGINE BRAKING) • The exhaust brake feature will only function when the driver turns the exhaust brake switch to the ON position. • The switch is located on the switch bank below the audio system. • Once the switch is in the ON position and the vehicle is moving faster than 5 mph (8 km/h), the exhaust brake will automatically operate when the driver removes pressure from the accelerator pedal. • Exhaust braking is most effective when the engine RPM is higher.
OPERATING YOUR VEHICLE COOL–DOWN IDLE CHART – DIESEL ONLY Driving Conditions TURBOCHARGER "COOL DOWN" CHART Load Turbocharger Temperature Stop and Go Stop and Go Highway Speeds City Traffic Highway Speeds Uphill Grade Empty Medium Medium Max. GCWR Max. GCWR Max. GCWR Cool Warm Warm Warm Warm Hot Idle Time (in minutes) Before Shut Down Less than 1 1 2 3 4 5 POWER SLIDING REAR WINDOW • The switch for the power sliding rear window is located on the overhead console.
ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM 28
ELECTRONICS 29
ELECTRONICS NON-TOUCH-SCREEN RADIOS Media Center 130 (Sales Code RES) Media Center 130 with Satellite Radio (Sales Code RES + RSC) 30
ELECTRONICS NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not. • Your radio has many features that add to the comfort and convenience of you and your passengers.
ELECTRONICS TOUCH-SCREEN RADIO Media Center 430/430N CD/DVD/HDD (Sales Code RBZ/RHB) NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not.
ELECTRONICS • Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to be heard through the vehicle's speakers. • The functions of the portable device are controlled using the device buttons. The volume may be controlled using the radio or portable device. Clock Setting • Turn the radio on, then touch the screen where the time is displayed. • Touch the USER CLOCK soft-key (Navigation radio only).
ELECTRONICS Copy Pictures To The Hard-Drive • Insert either a CD or a USB device containing your pictures in JPEG format into the USB port on the radio face. • Touch the MY FILES soft-key, then go to the MANAGE MY FILES screen. • Touch the MY PICTURES soft-key to get an overview of the currently stored images. • Touch one of the ADD PICTURES soft-keys, then select the type of media inserted. • Use the PAGE soft-keys to page through a list of pictures and press the picture you would like to import.
ELECTRONICS Map • Touch the NAV soft-key in the upper-right corner of your radio screen, to access the Navigation system. • Touch the View Map soft-key to display a map of your current position. Finding a Point of Interest • Touch the NAV soft-key in the upper-right corner of your radio screen, to access the Navigation system. • Touch the Where To? soft-key to program a destination. • Next touch one of the subcategories to search for your destination.
ELECTRONICS SIRIUS Travel Link • To access SIRIUS Travel Link, press the MENU hard-key, then touch the Travel Link soft-key. NOTE: SIRIUS Travel Link requires a subscription, sold separately after trial subscription included with vehicle purchase. • SIRIUS Travel Link brings a wealth of useful information into your vehicle and right to your fingertips: • Weather • View detailed weather conditions at your current location. • Ski Info • View ski and snowboarding conditions at ski resorts.
ELECTRONICS Uconnect™ Phone • To determine if your vehicle is equipped with Uconnect™ Phone, press the Uconnect™ Phone button . If your vehicle has this feature, after a couple seconds you will hear a voice prompt. If not, you will see a message on the radio “Uconnect phone not available”. • The Uconnect™ Phone is a voice-activated, hands-free, in-vehicle communications system with Voice Command Capability (see Voice Command section).
ELECTRONICS Phonebook Edit • Press the Phone button . • (After the BEEP), say “phonebook”. • (After the BEEP), say “new entry” or “list names” or “delete”. • Follow the prompts. Receiving A Call – Accept (And End) • When an incoming call rings/is announced on Uconnect™, press the Phone button . • To end a call, press the Phone button . Mute (Or Unmute) Microphone During Call • During a call, press the Voice Command button . • (After the BEEP), say “mute” (or “mute off”).
ELECTRONICS Uconnect™ VOICE COMMAND • The Uconnect™ Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, HDD, Uconnect™ Phone, a memo recorder, and supported portable media devices. • When you press the Voice Command button located on the radio faceplate or steering wheel, you will hear a beep. The beep is your signal to give a command. If you do not say a command within a few seconds, the system will present you with a list of options.
ELECTRONICS iPod®/USB/MP3 CONTROL • There are many ways to play music from iPod® players or other portable devices through your vehicle's speakers. Your choices depend on what radio your vehicle is equipped with. • The radio sales code is located on the lower right side of the radio faceplate.
ELECTRONICS WARNING! Do not plug in or remove the iPod® or external device while driving. Failure to follow this warning could result in a collision. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to Programmable Features in this guide.
ELECTRONICS PROGRAMMABLE FEATURES Electronic Vehicle Information Center (EVIC) – If Equipped • The EVIC can be used to program the following Personal Settings. Press the or DOWN button until SYSTEM SETUP displays, then press the UP . Scroll through the settings using the UP or DOWN SELECT button button. Press the SELECT button to change the setting. • Select Language • Nav-Turn By Turn • Auto Door Locks • Auto Unlock Doors • Remote Unlock Sequence • RKE Linked To Memory • Remote Start Comfort Sys.
ELECTRONICS Auto Door Lock • To have the doors lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h): • Enter your vehicle, close all the doors and fasten your seat belt. • Within 15 seconds, cycle the ignition switch from the OFF position to the ON position a minimum of four times, ending in the OFF position (do not start the engine). • Within 30 seconds, press the driver’s door lock switch in the LOCK direction. A single chime will indicate that programming is complete.
ELECTRONICS POWER INVERTER • A 115 Volt, 150 Watt power inverter outlet is located on the lower instrument panel next to the climate control knob. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. • To turn on the power outlet, press the switch once. • Press the switch a second time to turn the power outlet off. The status indicator of the AC power inverter indicates whether the inverter is producing AC power.
ELECTRONICS POWER OUTLETS • There are three possible 12 Volt power outlets located in the vehicle. Lower left and lower right of the instrument panel and inside the upper lid of the center storage compartment. A key symbol on the outlet cover indicates that the key must be in the ON or ACC positions for the outlet to provide power. The battery symbol on the outlet cover indicates that the outlet is connected to the battery, and can provide power at all times..
OFF-ROAD CAPABILITIES FOUR-WHEEL DRIVE OPERATION • The electronically shifted and manually shifted transfer case provides four mode positions. • Two-wheel drive high range (2H) WARNING! • Four-wheel drive high range (4H) You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
UTILITY TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) NOTE: For additional trailer towing information (maximum trailer weight ratings) refer to the following website addresses: • http://www.ramtrucks.com. • http://www.ramtruck.ca (Canada). INTEGRATED TRAILER BRAKE MODULE • The Integrated Trailer Brake Controller allows you to automatically or manually activate the electronic brakes on properly equipped trailers for greater stopping power on downhill grades.
UTILITY • Release the brake pedal for five seconds and ensure that there is no vehicle movement. • Repeat the previous two steps with the transmission in DRIVE. • Remove the key fob from the ignition switch. • Shift the transmission into PARK and apply the parking brake. • Attach the vehicle to the tow vehicle with the tow bar and release the parking brake.
UTILITY AUXILIARY SWITCHES • There are four auxiliary switches located in the lower switch bank of the instrument panel which can be used to power various electronic devices. Connections to the switches are found under the hood in the connectors attached to the auxiliary Power Distribution Center. • For further information on using the auxiliary switches please refer to the Dodge Body Builders Guide by accessing www.dodge.com/bodybuilder and choosing the appropriate links.
WHAT TO DO IN EMERGENCIES 24-HOUR TOWING ASSISTANCE • Dial toll-free 1-800-521-2779 or 1-800-363-4869 for Canadian residents. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. • Briefly describe the nature of the problem and answer a few simple questions. • You will be given the name of the service provider and an estimated time of arrival.
WHAT TO DO IN EMERGENCIES - Malfunction Indicator Light (MIL) • Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles. In most situations, the vehicle will drive normally and not require towing.
WHAT TO DO IN EMERGENCIES - SERV (Service) 4WD Indicator Light • If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest service center and have the vehicle serviced immediately. - Transmission Temperature Warning Light • This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. Hub Caps/Wheel Covers — If Equipped • The hub caps must be removed before raising the vehicle off the ground. • For single rear-wheel (SRW) models, use the blade on the end of the lug wrench to pry the hub cap off.
WHAT TO DO IN EMERGENCIES • For rear wheels, place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. • Turn the jack screw clockwise to firmly engage the jack saddle with the lift area. • Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. • Remove the lug nuts and wheel.
WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
WHAT TO DO IN EMERGENCIES JUMP-STARTING • If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. • Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.
WHAT TO DO IN EMERGENCIES Jump-Starting Procedure • Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. • Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. • Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery.
WHAT TO DO IN EMERGENCIES WARNING! • When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above the freezing point before attempting a jump-start. • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.
WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE • If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever. Column Shifter • Tilt the steering wheel to the full up position and firmly set the parking brake. • Turn the Key Fob to the ACC or ON/RUN position without starting the engine. • Press and maintain firm pressure on the brake pedal.
Recommended Method Recommended Method Not Permitted Not Permitted Transfer case must be in NEUTRAL and transmission in PARK Ignition key must be in unlocked OFF position Must use appropriate tow bar device Two-Wheel Drive Transmission not operable Two-Wheel Drive Transmission operable Four-Wheel Drive Flatbed Towing (all four wheels suspended OFF the ground) Recommended Method Flat Towing (all four wheels on the ground) Model TOWING A DISABLED VEHICLE Shift lever must be in NEUTRAL, the speed les
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE • If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then, move the shift lever back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the hood release lever located below the steering wheel at the base of the instrument panel. • Reach into the opening beneath the center of the hood and move the safety latch lever while lifting the hood at the same time. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
5.
6.
MAINTAINING YOUR VEHICLE FUEL FILTER/WATER SEPARATOR — DIESEL ONLY Draining Fuel/Water Separator • If the “Water in Fuel” indicator light is illuminated and an audible chime is heard five times, you should stop the engine and drain the water from the separator. • The drain is located on the bottom of the Fuel Filter and Water Separator assembly which is located on the driver's side of the engine.
MAINTAINING YOUR VEHICLE EXHAUST REGENERATION — DIESEL ONLY • Under certain conditions, your Cummins® diesel engine and exhaust after-treatment system may never reach the conditions required to remove the trapped particulate matter. If this occurs, the “Exhaust System — Regeneration Required Now” message will be displayed on the EVIC screen in your cluster and you will hear one chime to alert you of this condition.
MAINTAINING YOUR VEHICLE DIESEL EXHAUST FLUID • Diesel Exhaust Fluid (DEF) sometimes known simply by the name of its active component, UREA—is a key component of selective catalytic reduction (SCR) systems, which help diesel vehicles meet stringent emission regulations. DEF is a liquid reducing agent that reacts with engine exhaust in the presence of a catalyst to convert smog-forming nitrogen oxides (NOx) into harmless nitrogen and water vapor.
MAINTAINING YOUR VEHICLE • DEF is subject to freezing at the lowest temperatures. For example, DEF may freeze at temperatures at or below 12° F (-11° C). The system has been designed to operate in this environment. NOTE: When working with DEF, it is important to know that: • Any containers or parts that come into contact with DEF must be DEF compatible (plastic or stainless steel). Copper, brass, aluminum, iron or non-stainless steel should be avoided as they are subject to corrosion by DEF.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Engine Coolant 5.7L 3500 Models Engine Coolant 6.7L Turbo Diesel Engine Engine Oil with Filter 5.7L Engine Oil with Filter 6.7L Turbo Diesel Engine Fuel Selection 5.7L Fluid, Lubricant, or Genuine Part MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Fuel Selection 6.7L Turbo Diesel Use good quality diesel fuel from a reputable supplier in your vehicle. Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system. For most year-round service, No.
MAINTAINING YOUR VEHICLE Fluid, Lubricant, or Genuine Part Automatic MOPAR® ATF+4® Automatic Transmission (5-Speed Transmission Fluid or equivalent licensed ATF+4® 545RFE) product. Automatic MOPAR® AS68RC Automatic Transmission (6-Speed Transmission Fluid or equivalent. AS68RC) Clutch Linkage MOPAR® Multi-Purpose Grease, NLGI Grade 2 E.P. or equivalent. Manual Transmission MOPAR® ATF+4® Automatic Transmission Fluid or G-56 equivalent licensed ATF+4® product.
74 Change the transfer case fluid if using your vehicle for any of the following: fleet or frequent trailer towing. Inspect the transfer case fluid. Inspect the front and rear axle fluid, change if using your vehicle for fleet, off-road or frequent trailer towing. Replace the engine air cleaner filter. X X Inspect the exhaust system. X X X X X X 39,000 18 24,000 Inspect the CV joints. Inspect the brake linings; replace if necessary.
Adjust parking brake on vehicles equipped with four wheel disc brakes. X 78,000 36 48,000 91,000 42 56,000 • Refer to the Owner's Manual on the DVD for the complete maintenance schedule. Flush and replace power steering fluid. Inspect and replace PCV valve if necessary. Flush and replace the engine coolant at 104,000 miles (169,000 km) or 60 months whichever comes first. Flush and replace the engine coolant at 60 months or 104,000 miles (169,000 km) whichever comes first.
MAINTAINING YOUR VEHICLE Maintenance Record (Gasoline Engine) Odometer 8,000 Miles (13,000 km) or 6 Months 16,000 Miles (26,000 km) or 12 Months 24,000 Miles (39,000 km) or 18 Months 32,000 Miles (52,000 km) or 24 Months 40,000 Miles (65,000 km) or 30 Months 48,000 Miles (78,000 km) or 36 Months 56,000 Miles (91,000 km) or 42 Months 64,000 Miles (104,000 km) or 48 Months 72,000 Miles (117,000 km) or 54 Months 80,000 Miles (130,000 km) or 60 Months 88,000 Miles (143,000 km) or 66 Months 96,000 Miles (156,000
X X X Rotate the tires. Lubricate front drive shaft fitting (4x4). Lubricate outer tie rod ends. 18 24 30 36 42 48 X X Check the Diesel Exhaust Fluid (DEF) tank; refill if necessary. X X • Refer to the Owner's Manual on the DVD for the complete maintenance schedule. X Change automatic transmission fluid. X X Inspect wheel bearings.
MAINTAINING YOUR VEHICLE Maintenance Record (Diesel Engine) Odometer 7,500 Miles (12,000 km) or 6 Months 15,000 Miles (24,000 km) or 12 Months 22,500 Miles (36,000 km) or 18 Months 30,000 Miles (48,000 km) or 24 Months 37,500 Miles (60,000 km) or 30 Months 45,000 Miles (72,000 km) or 36 Months 52,500 Miles (84,000 km) or 42 Months 60,000 Miles (96,000 km) or 48 Months 67,500 Miles (108,000 km) or 54 Months 75,000 Miles (120,000 km) or 60 Months 82,500 Miles (132,000 km) or 66 Months 90,000 Miles (144,000 km
MAINTAINING YOUR VEHICLE FUSES Integrated Power Module (fuses) • The Integrated Power Module is located in the engine compartment near the battery. This center contains cartridge fuses and mini fuses.
MAINTAINING YOUR VEHICLE Cavity M17 M18 M19 80 Cartridge Fuse Mini Fuse 25 Amp Natural 25 Amp Natural 5 Amp Tan M20 M21 M22 M23 M24 M25 M26 M27 M28 25 Amp Natural 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Blue 10 Amp Red M29 M30 M31 M32 M33 M34 15 Amp Blue 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 15 Amp Blue M35 M36 M37 M38 M39 M40 M41 20 Amp Yellow 20 Amp Yellow 10 Amp Red 20 Amp Yellow 30 Amp Green 25 Amp Natural 15 Amp Blue M42 M43 M44 M
MAINTAINING YOUR VEHICLE Cavity M53 Cartridge Fuse M54 Mini Fuse 15 Amp Blue 20 Amp Yellow Description IGN R/S-MFSW/CNN/SCM/ TPM/RR View IOD — Spare CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in a electrical system failure.
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel's protective finish.
CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–866–726–4636 CHRYSLER CANADA INC. CUSTOMER CENTER P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English) Phone: 1–800–387–9983 (French) ASSISTANCE FOR THE HEARING IMPAIRED • To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center.
CONSUMER ASSISTANCE NOTE: A street address is required when ordering manuals (no P.O. Boxes). NOTE: • The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep, Ram Truck and Dodge websites. • Click on the "For Owners" tab, select "Owner/Service Manuals", then select your desired model year and vehicle from the drop down lists. REPORTING SAFETY DEFECTS IN THE 50 UNITED STATES AND WASHINGTON, D.C.
MOPAR ACCESSORIES AUTHENTIC ACCESSORIES BY MOPAR® • The following highlights just some of the many Authentic Ram Truck Accessories by Mopar featuring a fit, finish, and functionality specifically for your Ram Truck. • In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factory-approved.
INDEX Adjustable Pedals . . . . . . . . . . . 18 Air Conditioning . . . . . . . . . . 24,25 Airbag . . . . . . . . . . . . . . . . . . 11 Airbag Light . . . . . . . . . . . . . . 51 Alarm, Panic . . . . . . . . . . . . . . . 8 Anti-Lock Brake System (ABS) . . . 51 Arming Theft System (Security Alarm) . . . . . . . . . . . . 10 Audio Jack . . . . . . . . . . . . . . . 32 Audio Settings . . . . . . . . . . . . . 31 Automatic Headlights . . . . . . . 22,52 Automatic Temperature Control (ATC) . . . . . . . . .
INDEX Idle Up Feature . . . . . . . . . . . . 26 Instrument Cluster . . . . . . . . . . . 6 Indicators . . . . . . . . . . . . . . . 7 Instrument Cluster Warning Lights . . . . . . . . . . . . . . . . . 6,50 Integrated Trailer Brake Controls . . 47 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . . . . . . . 21 Introduction . . . . . . . . . . . . . . . 2 Inverter Outlet (115V) . . . . . . . . . 44 Inverter, Power . . . . . . . . . . . . . 44 iPod®/USB/MP3 Control . . . . . . .
INDEX Remote . . . . . . . . . . . . . . . . 9 Starting Procedures (Diesel Engines) . . . . . . . . . . . . . . . . . 19 Steering Tilt Column . . . . . . . . . . . . . . 18 Wheel, Heated . . . . . . . . . . . . 18 Steering Wheel Audio Controls . . . 36 Store Radio Presets . . . . . . . . 31,33 Supplemental Restraint System Airbag . . . . . . . . . . . . . . . . . . 11 Temperature Control, Automatic (ATC) . . . . . . . . . . . . . . . . Theft Alarm (Security Alarm) . . Theft System Arming . . . . . .
Driving and Alcohol: Drunken driving is one of the most frequent causes of collisions. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to a collision. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking.
RAMTRUCKS.COM This guide has been prepared to help you get quickly acquainted with your new RAM and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation/Media Center Manuals, Multimedia User Manual and other Warning Labels in your vehicle. Not all features shown in this guide may apply to your vehicle.
