2012 Ram Truck Chassis Cab Chrysler Group LLC 12DD43-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents.
INTRODUCTION 5
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. also be supplied with your vehicle.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ General Information . . . . . . . . . . . . . . . . . . . 18 ▫ Wireless Ignition Node (WIN) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 19 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ Removing Key Fob From Ignition . . . . . . . . . . 14 ▫ Key-In-Ignition Reminder . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . 23 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 37 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 38 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . 39 ▫ Transmitter Battery Replacement . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver And Right Front Passenger 䡵 Engine Break-In Recommendations . . . . . . . Supplemental Restraint System (SRS) — Air 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 ▫ Transporting Passengers . . . . . . . . . . . . . ▫ Air Bag System Components . . . . . . . . . . . . . 54 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . ▫ Advanced Front Air Bag Features . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Key Fob with Remote Keyless Entry (RKE) — If Equipped Your vehicle may use a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Standard Blade Ignition Key — If Equipped Your vehicle may use a standard blade key ignition system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK (if equipped with an automatic transmission). Turn the Key Fob to the OFF then pull the key out with your other hand. position and then remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. CAUTION! • If your vehicle battery becomes low or dead, your Key Fob will become locked in the ignition. • Do not attempt to remove the Key Fob while in this condition, damage could occur to the Key Fob or ignition module. Only remove the emergency key for locking and unlocking the doors.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: A Key Fob that has not been programmed is also considered an invalid key. CAUTION! The Sentry Key威 Immobilizer system is not compatDuring normal operation, after turning on the ignition ible with some after-market remote starting systems. switch, the Vehicle Security Light will turn on for three Use of these systems may result in vehicle starting seconds for a bulb check. If the light remains on after the problems and loss of security protection.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! Always remove the Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 VEHICLE SECURITY ALARM — IF EQUIPPED The Vehicle Security Alarm monitors the vehicle doors and ignition for unauthorized operation. When the Vehicle Security Alarm is activated, interior switches for door locks are disabled. The system provides both audible and visible signals, for the first three minutes the horn will sound and the headlights will turn on, the park lamps and/or turn signals will flash and Vehicle Security Light will flash repeatedly.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Security Alarm will also disarm if a programmed Sentry Key威 is inserted into the ignition switch. To exit the alarming mode, press the RKE transmitter UNLOCK button, or insert a programmed Sentry Key威 into the ignition switch. The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • The illuminated entry system will not operate if the dimmer control is in the “dome defeat” position (extreme bottom position). 2 REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock the doors and activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a Key Fob with RKE transmitter. The transmitter does not need to be pointed at the vehicle to activate the system.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seconds to unlock all doors. The turn signal lights will than ten seconds. Then, press and hold the UNLOCK flash to acknowledge the unlock signal. The illuminated button while still holding the LOCK button. entry system will also turn on. 2. Release both buttons at the same time. Remote Key Unlock, Driver Door/All Doors First 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Flash Lamps With Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 3.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn With Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/CustomerProgrammable Features (System Setup)” in “Understanding Your Instrument Panel” for further information. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 The Panic Alarm will stay on for three minutes unless Transmitter Battery Replacement you turn it off by either pressing the PANIC button a The recommended replacement battery is one CR2032 second time or drive the vehicle at a speed of 5 mph battery. (8 km/h) or greater. NOTE: • Perchlorate Material — special handling may apply. NOTE: • The interior lights will turn off if you turn the ignition See www.dtsc.ca.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To assemble the RKE transmitter case, snap the two If your RKE transmitter fails to operate from a normal distance, check for these two conditions: halves together. 1. A weak battery in the RKE transmitter. The expected General Information This device complies with Part 15 of the FCC rules and life of the battery is a minimum of three years. RSS 210 of Industry Canada. Operation is subject to the 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • HAZARD switch off • BRAKE switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed • Fuel meets minimum requirement • System not disabled from previous remote start event • Vehicle theft alarm not active W
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted — Hood Ajar • Remote Start Aborted — Fuel Low • Remote Start Aborted — System Fault • Remote Start Disabled — Start Vehicle to Reset The EVIC message stays active until the ignition is turned to the ON/RUN position. • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. • The park lamps will turn on and remain on during Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 message “Turn To On” will flash in the EVIC until you NOTE: To avoid unintentional shut downs, the system turn the ignition switch to the ON/RUN position. will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote • “Remote Start Active — Key To Run” will display in Start request. the EVIC until you insert and turn the key to ON/ To Exit Remote Start Mode And Drive The Vehicle RUN position.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Information Center (EVIC)/Customer-Programmable Features (System Setup)” in “Understanding Your Instrument Panel”. DOOR LOCKS Manual Door Locks Front and rear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! (Continued) • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the key fob in or near the vehicle, and do not leave the ignition in the ACC or ON/RUN position. A child could operate power windows, other controls, or move the vehicle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob. Auto Unlock Doors Programming — If Equipped The Auto Unlock Doors feature can be enabled or disabled as follows: Automatic Door Locks — If Equipped When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 2 Child-Protection Door Lock Location To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to engage and disengage the Child-Protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. Child Lock Control WARNING! Avoid trapping anyone in a vehicle in a collision.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WINDOWS • After setting the Child-Protection Door Lock system, Power Windows – If Equipped always test the door from the inside to make certain it is in the desired position. • For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the Crew Cab models. The windows will operate when the ignition switch is turned to the ON/RUN or ACC position, and for up to 10 minutes after the ignition is turned OFF or until a front door is opened.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press to the first detent conditions may trigger the auto reverse function unexpectedly during auto closure. If this happens, pull the and release it when you want the window to stop. switch lightly to the first detent and hold to close the Auto-Up Feature With Anti-Pinch Protection window manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window LOCKOUT Switch (4–Door Models Only) The window LOCKOUT switch on the driver’s door allows you to disable the window control on the rear passenger doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE normal occurrence and can be minimized. If the rear • All seat belt systems (except driver’s regular/Crew windows are open and buffeting occurs, open the front Cab威, first and second row center position for Crew and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Regular Cab Front Center Three Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the seat belt tongue into the center red slot on the black buckle.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! In Use Position • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE activate the ALR. If the ALR is activated you will hear a ratcheting sound as the belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupants mid-section. Slide the latch plate into the buckle until you hear a ⬙click.⬙ Automatic Locking Retractor Mode (ALR) — If Equipped In this mode, the shoulder belt is automatically prelocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Enhanced Seat Belt Use Reminder System (BeltAlert姞) BeltAlert威 is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert威) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both front seat belts are fastened.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts And Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon seat position.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • After any accident, the vehicle should be taken to an Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage authorized dealer immediately. driver and front passenger (if equipped) air bags. This Air Bag System Components system provides output appropriate to the severity and Your vehicle may be equipped with the following air bag type of collision as determined by the Occupant Restraint system components: Controller (ORC).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ride properly buckled up in the rear seat. Never allow If the air bag system in this vehicle needs to be modified children to slide the shoulder belt behind them or under to accommodate a disabled person, contact the Customer their arm. Center. Phone numbers are provided under ⬙If You Need Assistance⬙.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The Advanced Front Air Bags will not deploy in all frontal collisions, including some that may produce subOccupant Restraint Controller (ORC) stantial vehicle damage — for example, some pole colliThe ORC is part of a Federally regulated safety system sions, truck underrides, and angle offset collisions. On required for this vehicle.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position. If the key is in the LOCK position, in the ACC position, or not in the ignition, the air bag system is not on and the air bags will not inflate. The ORC contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Driver And Passenger Advanced Front Air Bag Inflator Units The Driver and Passenger Advanced Front Air Bag Inflator Units are located in the center of the steering wheel and on the right side of the instrument panel (if equipped). When the ORC detects a collision requiring the Advanced Front Air Bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Advanced Front Air Bags.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from IGN ON to IGN OFF. If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Do not drive your vehicle after the air bags have de- Maintaining Your Air Bag System ployed. If you are involved in another collision, the air WARNING! bags will not be in place to protect you. WARNING! Deployed air bags cannot protect you in another collision. Have the air bags replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat including your trim cover and cushion needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rearwardfacing or forward-facing in the vehicle.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. Refer to “Lower Anchors and Tether for CHildren (LATCH)”. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 you make sure that you can install the child restraint in • If the belt still can’t be tightened, or if pulling and the vehicle where you will use it before you buy it. pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate • The restraint must be appropriate for your child’s around, and insert the latch plate into the buckle weight and height. Check the label on the restraint for again.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 cushion, and tether strap anchorages, located behind the Child restraint systems having attachments designed to seat back (refer to “Child Restraint Tether Anchor”). connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Installing The Child Restraint System • When using the LATCH attaching system to install a WARNING! child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out Do not install child restraint systems equipped with of reach of children. It is recommended that before LATCH mechanisms in the center position of a Crew installing the child restraint, buckle the seat belt so the Cab model with a bench rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 We urge you to carefully follow the directions of the WARNING! manufacturer when installing your child restraint. Many, Improper installation of a child restraint to the but not all, restraint systems will be equipped with LATCH anchorages can lead to failure of an infant or separate straps on each side, with each having a hook or child restraint. The child could be badly injured or connector, and a means for adjusting the tension in the killed.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The chart below defines the seating positions with an Installing a Child Restraint with an ALR: Automatic Locking Retractor (ALR) or a cinching latch 1. To install a child restraint with ALR, first, pull enough plate. of the seat belt webbing from the retractor to route it through the belt path of the child restraint. Slide the latch Regular Cab plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 retractor to route it through the belt path of the child Regular Cab models have two tether anchorages, one restraint. Slide the latch plate into the buckle until you each behind the front center and right seats. Crew Cab models have three anchorages, one behind each of the hear a “click.” rear seats. 2. Finally, pull on any excess webbing to tighten the lap portion around the child restraint.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Multiple Child Restraint Installation Sequence (Crew Cab — Rear Seats) Crew Cab 2 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by raising the head restraint and reaching between the rear glass and rear seat. Head Restraint Adjustment 2.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the anchor loop. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 WARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 87 ▫ Automatic Dimming Mirror — If Equipped . . . 87 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 88 ▫ Outside Mirrors Folding Feature . . . . . . . . . . 89 ▫ Power Mirrors — If Equipped . . . . . . . . . . . . 90 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ General Information . . . . . . . . . . . . . . . . . . 123 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . 138 䡵 Voice Command — If Equipped . . . . . . . . . . . 123 ▫ 40-20-40 Front Bench Seat — If Equipped . . . 140 ▫ Voice Command System Operation . . . . . . . . 123 䡵 Driver Memory Seat — If Equipped . . . . . . . . 140 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Voice Training . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . 149 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . 149 ▫ Parking Lights And Panel Lights . . . . . . . . . 149 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 150 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 150 ▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Overhead Console — If Equipped . . . . . . . . . . 163 ▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . 164 ▫ Center Storage Compartment — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 176 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 165 䡵 Cigar Lighter And Ash Receiver — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). 3 Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle).
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 WARNING! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex right side mirror.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Power Mirror Controls 1 — Mirror Select Buttons 2 — Mirror Control Power Mirror Controls To adjust a mirror, press the mirror select button for the The power mirror controls consist of mirror select but- mirror that you want to adjust. Using the mirror control tons and a four-way mirror control switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the light. 3 Power Mirror Movement Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated by pressing the rear window defroster button.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Slide-On-Rod” Features Of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun. To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 3 Trailer Towing Position Blindspot Mirror NOTE: Fold the trailer towing mirrors rearward prior to Uconnect™ Phone — IF EQUIPPED entering an automated car wash. Uconnect™ Phone is a voice-activated, hands-free, invehicle communications system. Uconnect™ Phone alA small blindspot mirror is located next to main mirror lows you to dial a phone number with your mobile and can be adjusted separately. phone using simple voice commands (e.g.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile phone’s audio is transmitted through your vehi- Uconnect™ Phone allows you to transfer calls between cle’s audio system; the system will automatically mute the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s your radio when using the Uconnect™ Phone. microphone for private conversation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. Voice Command Button Actual button location may vary with the radio. The individual buttons are described in the “Operation” section.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Voice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structure. Voice commands are required after most Uconnect™ Phone prompts. You will be prompted for a specific command and then guided through the available options. example, you can use the compound form voice command “Phonebook New Entry”, or you can break the compound form command into two voice commands: “Phonebook” and “New Entry”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Cancel Command • When prompted, after the beep, say “Pair a Device” At any prompt, after the beep, you can say “Cancel” and and follow the audible prompts. you will be returned to the main menu. However, in a • You will be asked to say a four-digit Personal Identifew instances the system will take you back to the fication Number (PIN), which you will later need to previous menu. enter into your mobile phone.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone to use if multiple mobile phones are in the • The Uconnect™ Phone will confirm the phone number vehicle at the same time. For example, if priority three and then dial. The number will appear in the display and priority five phones are present in the vehicle, the of certain radios. Uconnect™ Phone will use the priority three mobile Call By Saying A Name phone when you make a call. You can select to use a button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • The Uconnect™ system will confirm the name and • When prompted, enter the number designation (e.g., then dial the corresponding phone number, which “Home”, “Work”, “Mobile”, or “Other”). This will may appear in the display of certain radios. allow you to store multiple numbers for each phonebook entry, if desired.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download – Automatic Phonebook • Depending on the maximum number of entries downTransfer From Mobile Phone loaded, there may be a short delay before the latest If equipped and specifically supported by your phone, downloaded names can be used. Until then, if availUconnect™ Phone automatically downloads names (text able, the previously downloaded phonebook is availnames) and number entries from your mobile phone’s able for use. phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in NOTE: the phonebook, call the number you just edited, or return • Editing names in the phonebook is recommended to the main menu. when the vehicle is not in motion. “Phonebook Edit Entry” can be used to add another • Automatic downloaded phonebook entries cannot be phone number to a name entry that already exists in the deleted or edited.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “List Names” to hear a list of the entries in the phonebook from which you choose. To select one of the entries button while the from the list, press the Uconnect™ Phone is playing the desired entry and say “Delete”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • After the “Ready” prompt and the following beep, say mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be “Phonebook List Names”. accessed through the Uconnect™ Phone. Check with • The Uconnect™ Phone will play the names of all the your mobile service provider for the features that you phonebook entries, including the downloaded phonehave. book entries, if available.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile phone. Press the button to place the current Place/Retrieve A Call From Hold To put a call on hold, press the button until you hear call on hold and answer the incoming call. a single beep. This indicates that the call is on hold. To NOTE: The Uconnect™ Phone compatible phones in the bring the call back from hold, press and hold the market today do not support rejecting an incoming call button until you hear a single beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Three-Way Calling To initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “Making a Second Call While Current Call is in Progress”. After the second call has established, button until you hear a double press and hold the beep, indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the button.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can After selecting one of the languages, all prompts and continue on the Uconnect™ Phone for a certain dura- voice commands will be in that language. tion, after which the call is automatically transferred NOTE: After every Uconnect™ Phone language change from the Uconnect™ Phone to the mobile phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After the “Ready” prompt and the following beep, say “Emergency” and the Uconnect™ Phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. WARNING! To use your Uconnect™ Phone System in an emergency, your mobile phone must be: • turned on, • paired to the Uconnect™ System, • and have network coverage.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mexico City in Mexico). Please refer to the 24-Hour “Towing Assistance” coverage details on the DVD in the Warranty Information Booklet and the 24-Hour Towing Assistance references. Working With Automated Systems This method is used in instances where one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 is also to be used for navigating through an automated Barge In — Overriding Prompts customer service center menu structure, and to leave a The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice number on a pager. command immediately. For example, if a prompt is You can also send stored Uconnect™ phonebook entries asking “Would you like to pair a phone, clear a...
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone And Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your mobile phone, the Uconnect™ Phone will provide notification to inform you of your phone and network status when you are attempting to make a phone call using Uconnect™ Phone. The status is given for network signal strength, phone battery strength, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Advanced Phone Connectivity List Paired Mobile Phone Names Transfer Call To And From Mobile Phone The Uconnect™ Phone allows ongoing calls to be transferred from your mobile phone to the Uconnect™ Phone without terminating the call. To transfer an ongoing call from your Uconnect™ Phone paired mobile phone to the button Uconnect™ Phone or vice versa, press the and say “Transfer Call”. • Press the button to begin.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say • You can also press the button at any time while the “Setup Select Phone” and follow the prompts. list is being played, and then choose the phone you wish to delete. • You can also press the button at any time while the list is being played, and then choose the phone that Things You Should Know About Your Uconnect™ Phone you wish to select.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • Press the button and say the “Voice Training, This will delete all phone pairing, phone book entries, and other settings in all language modes. The System will System Training, or Start Voice Training” command. prompt you before resetting to factory settings. You can either press the Uconnect™ Phone button to restore the factory setting or repeat the words and Voice Command phrases when prompted by the Uconnect™ Phone.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • low road noise, • smooth road surface, • Phonebook (Downloaded and Uconnect™ Phone Local) name recognition rate is optimized when the entries are not similar. • fully closed windows, • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • dry weather condition. • You can say “O” (letter “O”) for “0” (zero).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. Recent Calls If your phone supports “Automatic Phonebook Download”, Uconnect™ Phone can list your Outgoing, Incoming and Missed Calls. SMS Uconnect™ Phone can read or send new messages on your phone.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After reading a message, you can “Reply” or “Forward” List of Preset Messages: the message using Uconnect™ Phone. 1. Yes Send Messages: 2. No You can send messages using Uconnect™ Phone. To send 3. Where are you? a new message: • Press the button. 4. I need more direction. • After the “Ready” prompt and the following beep, say 5. “SMS Send” or “Send Message.” 6. • You can either say the message you wish to send or say 7. “List Messages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call • After the “Ready” prompt and the following beep, say “Setup, SMS Incoming Message Announcement,” you will then be given a choice to change it. Bluetooth威 Communication Link Mobile phones have been found to lose connection to the Uconnect™ Phone.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 3
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Alternate(s) Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no other pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the winbutton, listen dows are closed, and the heater/air conditioning fan is options, press the Voice Command set to low. for the beep, and say your command. button while the Pressing the Voice Command system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking. Please note the volume setting for this mode, you may say the following commands: Voice Command is different than the audio system.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Disc To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: Satellite Radio • “Track” (#) (to change the track) To switch to satellite radio mode, say “Sat” or “Satellite Radio”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 − “Continue” (to continue recording) • “Switch to system setup” − “Delete” (to delete the recording) • “Change to setup” • “Play Memos” (to play previously recorded memos) • “Main menu setup” or — During the playback you may press the Voice • “Switch to setup” button to stop playing memos.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers the Uconnect™ Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when you have reached the desired position.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch, the front of the seat cushion will move in the direction of the switch.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support. Heated Seats — If Equipped On some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. Press the switch once to select HIGHlevel heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE before automatically shutting OFF. The heated seats can indicator lights in each switch indicate the level of heat in shut OFF early or may not turn on when the seat is use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. already warm. Vehicle Equipped With Remote Start On models that are equipped with remote start, the driver’s heated seat can be programmed to come on during a remote start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 heat for a maximum of 60 minutes before switching to LOW heat. Once a seat has switched to the LOW heat setting it may operate for a maximum of 45 minutes before automatically shutting OFF. The heated seats can shut OFF early or may not turn on when the seat is already warm. Ventilated Seats — If Equipped On some models, both the driver and passenger seats are ventilated.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Adjuster — If Equipped Both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found under the seat cushion at the front edge of each seat. Pull up on the handle and slide the seat forward or backward to move the seat into the most comfortable position, then release the handle to lock the seat into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Manual Reclining Seats — If Equipped The recliner handle is located on the outside of the seat cushion and is used to adjust the seatback position.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Actuating the recliner handle will allow the seatback to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin behind the seat. To avoid injury, place your hand on the seatback and actuate the handle then position the seatback in the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Front Head Restraints To raise the head restraint, pull upward on the head restraint.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Head Restraints The outboard head restraints can be adjusted. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. NOTE: The rear center head restraint (Crew Cab only) is fixed and cannot be adjusted. 40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 NOTE: The power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to two RKE transmitters, each RKE transmitter linked to either of the two memory positions.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE system will recall any stored settings. Wait for the system 8. Within five seconds, press and release MEMORY to complete the memory recall before continuing to button 1 or 2 on the driver’s door. The next step must be Step 3. performed within five seconds if you desire to also use a RKE transmitter to recall memory positions. 3. Adjust the driver’s seat, recliner, and driver’s sideview mirror to the desired positions. 9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 driver’s mirror and the pedals stop moving. A delay of one second will occur before another recall can be NOTE: The vehicle must be in PARK to recall memory selected. positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the Electronic To Disable A RKE Transmitter Linked To Memory Vehicle Information Center (EVIC). 1.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE transmitter linked to either memory position, repeat steps 1 through 5 for each RKE transmitter. ignition switch. The seat will then move forward approximately 2.5 in (60 mm) when the key is placed into the ignition and turned out of the LOCK position. NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time. • The seat will move to the position located 0.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 NOTE: The engine must be running before the head- delay can be cancelled by either turning the headlight switch on then off, or by turning the ignition ON. lights will turn on in the Automatic Mode. Headlights On With Wipers (Available With Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped The fog lights are turned on by placing the headlight rotary control in the parking light or headlight position and pushing in the headlight rotary control. Fog Light Switch The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 The brightness of the instrument panel lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odometer, radio and overhead console by rotating the control to the right until you hear a click. This feature is termed the “Parade” mode and is useful when headlights are required during the day.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light Lights-On Reminder The cargo lights are turned on by pressing on the cargo If the headlights, parking lights, or cargo lights are left on button. after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Daytime Running Lights — If Equipped The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn OFF.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-To-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. Windshield Wiper/Washer Switch Windshield Wiper Operation Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed and the wiper will operate for two to three cycles after the washer knob is released from this position. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the multifunction lever. Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 be adjusted when the system is locked out (“Adjust- HEATED STEERING WHEEL — IF EQUIPPED able Pedal Disabled — Cruise Control Engaged” or The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering “Adjustable Pedal Disabled — Vehicle In Reverse”. wheel has only one temperature setting.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running for the heated steering wheel to operate. WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.. This may cause the steering wheel heater to overheat. Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The system should be turned off when not in use.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set A Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press the SET (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. To Resume Speed To resume a previously set speed, push the RES (+) button and release. Resume can be used at any speed above 20 mph (32 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 decrease until the button is released. Release the button On steep hills, a greater speed loss or gain may occur so when the desired speed is reached, and the new set speed it may be preferable to drive without Electronic Speed Control. will be established. Pressing the SET (-) button once will result in a 1 mph (1.6 km/h) decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph (1.6 km/h).
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Power Sliding Rear Window Switch — If Equipped UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON or ACC positions for the outlet to provide power.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 3 Power Outlet — Upper Lid • Rear of the center console storage compartment — Crew Cab.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The key symbol indicates that this outlet can supply power when the key is in the ON or ACC positions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For vehicles equipped with a floor console the cuphold- To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. ers may be used. POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 The power inverter switch is located • Due to built-in overload protection, the power inverter on the switch bank below the Climate will shut down if the power rating is exceeded. Controls. To turn on the power outlet, WARNING! press the switch once. Press the switch a second time to turn the power outlet To avoid serious injury or death: off. • Do not use a three-prong adapter. • Do not insert any objects into the receptacles.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Instrument Panel Cupholders — (40–20–40 Seats) The cupholders are located in the pull-out tray on the center stack of the instrument panel. Front Instrument Panel Cupholders — Floor Storage Bin For vehicles equipped with bucket seats two cupholders are located in the floor storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage The glove box is located on the passenger side of the located in the center armrest. instrument panel and features both an upper (if equipped) and lower storage area.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Door Storage Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear Door Storage — Crew Cab Storage compartments are located in both the driver and passenger door trim panels.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 3 Upper Storage Compartment With the upper lid closed, pull on the lower handle to open the lower storage bin.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 3 Storage Bin Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Crew Cab Storage CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainers (Regular Cab REAR WINDOW FEATURES Models) Rear Window Defroster Retainer hooks which will hold plastic grocery bag The rear window defroster button is located on the handles are built into the back panel of the cab, behind climate control panel. Press this button to turn on the seats. the rear window defroster and the heated outside mirrors (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 186 ▫ EVIC Average Fuel Economy . . . . . . . . . . . . 212 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 187 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 212 䡵 Instrument Cluster — Premium . . . . . . . . . . . 188 ▫ Vehicle Info (Customer Information Features) . . . . . . . . . 213 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 189 ▫ Units . . . . . . . . . . .
184 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Media Center 730N/430/430N (RHR/RER/ RBZ/RHB) CD/DVD/HDD/NAV — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 ▫ Operating Instructions (Voice Command System) — If Equipped . . . . . . . . . . . . . . . . 222 ▫ Operating Instructions (Uconnect™ Phone) — If Equipped . . . . . . . . . . . . . . . . . . . . . . 222 䡵 Media Center 130 (Sales Code RES) . . . . . . . . . 222 ▫ Operating Instructions — Radio Mode . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 185 ▫ Controlling The iPod威 Or External USB Device Using Radio Buttons . . . . . . . . . . . . . 248 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 250 ▫ Bluetooth Streaming Audio (BTSA) . . . . . . . . 252 䡵 Steering Wheel Audio Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 253 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . .
186 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 6 — — — — — — Headlight Switch Instrument Cluster Radio Upper Switch Bank Upper Glove Compartment Lower Glove Compartment 7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank 10 — Cup Holders 11 — Climate Controls 12 — Power Outlet/Cigar Lighter 13 14 15 16 — — — — Transfer Case Position Switch Ignition Switch Hood Release Parking Brake Release
UNDERSTANDING YOUR INSTRUMENT PANEL 187 INSTRUMENT CLUSTER — BASE 4
188 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 189 INSTRUMENT CLUSTER DESCRIPTIONS • Check for an inoperative outside light bulb if either indicator flashes at a rapid rate. 1. Tachometer The Tachometer indicates engine speed in revolutions per 3. Fuel Gauge minute (RPM x 1000). Shows level of fuel in tank when ignition switch is in the ON/RUN position. CAUTION! Do not operate the engine with the tachometer pointer at high RPM for extended periods. Engine damage may occur. 4.
190 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealership for service. A hot engine cooling system is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 rotate at the same speed. Low range provides a greater required and you may experience reduced performance, gear reduction ratio to provide increased torque at the an elevated/rough idle or engine stall and your vehicle may require towing. wheels. 7. Electronic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Throttle Control (ETC) system.
192 UNDERSTANDING YOUR INSTRUMENT PANEL For vehicles equipped with a premium cluster this indicator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. 12. Oil Pressure Gauge — If Equipped The pointer should always indicate some oil pressure when the engine is running. A continuous high or low reading under normal driving conditions may indicate a lubrication system malfunction.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service.
194 UNDERSTANDING YOUR INSTRUMENT PANEL engine hours will be displayed for a period of 30 seconds cluster (Refer to ”Electronic Vehicle InformationCenter until the ignition is turned OFF or the engine is started. (EVIC) — If Equipped” for further information). Some of the above warnings will be displayed in the Electronic Vehicle Information Center (EVIC) Display Area located in the instrument cluster. Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 means the engine oil change interval may fluctuate 15. Engine Temperature Warning Light dependent upon your personal driving style. This light warns of an overheated engine condition. As engine coolant temperatures rise and the Unless reset, this message will continue to display each gauge approaches H, this indicator will illuminate time you turn the ignition switch to the ON/RUN and a single chime will sound after reaching a set position.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Center (EVIC). Refer to ”Electronic Vehicle Information For vehicles equipped with a premium cluster this indiCenter (EVIC) — If Equipped” for further information. cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information 16. Shift Lever Indicator Center (EVIC) — If Equipped” for further information. The Shift Lever Indicator is self-contained within the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS). In this case, the light will remain on until the condition has been corrected. If the problem is related 20.
198 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Do not operate the vehicle until the cause is corrected. on until the vehicle is started. If the bulb does not come This light does not indicate how much oil is in the engine. on during starting, have the condition investigated promptly. The engine oil level must be checked under the hood.
200 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 24.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 27. Transmission Temperature Warning Light WARNING! This light indicates that there is excessive transmission fluid temperature that might occur If the Transmission Temperature Warning Light is with severe usage such as trailer towing.
202 UNDERSTANDING YOUR INSTRUMENT PANEL 28. Seat Belt Reminder Light When the ignition switch is first turned to ON/ RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt remains unbuckled, the seat belt reminder light will flash or remain on continuously.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. NOTE: The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
204 UNDERSTANDING YOUR INSTRUMENT PANEL • Trip Information (in Odometer line) Press and release the DOWN button to scroll downward through the main menus and submenus. SELECT Button Press and release the SELECT button for access to main menus or sub-menus. Press and hold the SELECT button for two seconds to reset features. BACK Button Press the BACK button to scroll back to a previous menu or sub-menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Electronic Vehicle Information Center (EVIC) • Trailer Brake Connected Displays • Trailer Brake Disconnected When the appropriate conditions exist, the EVIC displays the following messages: • Lights On • Left front turn signal lamp out • Keyfob Battery Low • Right front turn signal lamp out • Wrong Key • Left rear turn signal lamp out • Damaged Key • Right rear turn signal lamp out • Key not programmed • Service air filter • Key In Ignition • Perform servic
206 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Four Wheel Drive System • Blind spot detection unavailable • Adjustable pedals unavail. • Automatic High Beams on • Cruise engaged • Automatic High Beams off • Adjustable pedals unavail. Veh.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 • Remote start aborted — Hood ajar EVIC Warning Lights • Remote start aborted — Fuel low • Door Ajar This light will turn on to indicate that one or more doors may be ajar.
208 UNDERSTANDING YOUR INSTRUMENT PANEL • Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 • Engine Temperature Warning Light • SERV 4WD This light warns of an overheated engine condiThe SERV 4WD light monitors the electric shift tion. As temperatures rise and the gauge ap4WD system. If the SERV 4WD light stays on or proaches H, this indicator will illuminate and a comes on during driving, it means that the single chime will sound after reaching a set threshold.
210 UNDERSTANDING YOUR INSTRUMENT PANEL light comes on, stop the vehicle and run the engine at idle • Loose Gascap Message or faster, with the transmission in NEUTRAL until the If the vehicle diagnostic system determines light goes off. that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap icon will CAUTION! display in the telltale display area.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 indicator system is duty-cycle based, which means the Distance To Empty (DTE) engine oil change interval may fluctuate dependent upon Shows the estimated distance that can be traveled with your personal driving style. the fuel remaining in the tank. This estimated distance is Unless reset, this message will continue to display each determined by a weighted average of the instantaneous time you turn the ignition switch to the ON position.
212 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased and the averaging will continue from the last fuel average reading before the reset. The Trip Functions mode displays the following information: • Trip A Shows the total distance traveled for Trip A since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the ODOMETER/TRIP ODOMETER button once to clear the resettable function being displayed. Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Compass / Temperature Display The compass readings indicate the direction the vehicle is facing. The EVIC will display one of eight compass readings and the outside temperature. NOTE: • The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperature is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 NOTE: A good calibration requires a level surface and 4. Press and release the SELECT button to start the an environment free from large metallic objects such as calibration. The “CAL” indicator will be displayed in the buildings, bridges, underground cables, railroad tracks, EVIC. etc. 5.
216 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 2. Press the UP or DOWN button until the System Setup (Customer-Programmable Features) menu is reached, then press the SELECT button. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Press and release the UP or DOWN button until System route, mile by mile, turn-by-turn until the final destination is reached. To make your selection, press and release Setup displays in the EVIC. the SELECT button until a check-mark appears next to Use the UP or DOWN button to display one of the the feature showing the system has been activated or the following choices. check-mark is removed showing the system has been deactivated.
218 UNDERSTANDING YOUR INSTRUMENT PANEL UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, press and release the SELECT button until “Driver Door 1st Press” or “All Doors 1st Press” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Horn With Remote Start When this feature is selected, a short horn sound will occur when the RKE transmitter REMOTE START button is pressed. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
220 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamps With Wipers When this feature is selected and the HEADLIGHT switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 and power outlets will remain active for up to 10 minutes after the ignition switch is turned OFF. Opening either front vehicle door will cancel this feature. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
222 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/ RHB) CD/DVD/HDD/NAV — IF EQUIPPED MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right NOTE: The sales code is located on the lower right side side of the radio faceplate. of the unit’s faceplate. Refer to your Uconnect™ Multimedia RHR, RER, RBZ or RHB user’s manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection. Holding either button will bypass position to operate the radio. stations without stopping, until you release it. Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio.
224 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the knob to save time change. mid-range tones. 5. To exit, press any button/knob, or wait five seconds. Push the rotary TUNE/SCROLL control knob a third RW/FF time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Push the rotary TUNE/SCROLL control knob again to You may add a second station to each pushbutton by repeating the above procedure with this exception: Press exit setting tone, balance, and fade. the SET/RND button twice and SET 2 will show in the AM/FM Button display window. Each button can be set for SET 1 and Press the buttons to select either AM or FM mode. SET 2 in both AM and FM.
226 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or the radio will reinsert the CD but will not play it. RW or another CD button is pressed. The RW (Reverse) A disc can be ejected with the radio and ignition OFF. button works in a similar manner.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Notes on Playing MP3 Files • Maximum number of files: 255 The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited. For large numbers writing MP3 files, pay attention to the following restricof files and/or folders, the radio may be unable to tions.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio. side of the radio faceplate. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
232 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in “Understanding The Features Of Your Vehicle”.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text will begin to blink. message broadcast from an FM station (FM mode only). 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be sePush the rotary TUNE/SCROLL control knob a third lected.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Program Type Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk 16-Digit Character Display Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Program Type Top 40 Weather 16-Digit Character Display Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be t
236 UNDERSTANDING YOUR INSTRUMENT PANEL hours, press the TUNE/SCROLL control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side TUNE/SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
238 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or the radio will reinsert the CD but will not play it. another CD button is pressed. The RW (Reverse) button A disc can be ejected with the radio and ignition OFF. works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Notes On Playing MP3 Files • Maximum number of files: 255 The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited. For large numbers writing MP3 files, pay attention to the following restricof files and/or folders, the radio may be unable to tions.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. TIME Button (Auxiliary Mode) Press this button to change the display to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. using the TUNE/SCROLL control knob until Sirius ID is selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will • The vehicle is parked in an underground parking remain tuned to the new channel until you make another structure or under a physical obstacle. selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 By pressing the SEEK button when the Music Type RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons function is active, the radio will be tuned to the next causes the tuner to search for the next channel in the channel with the same selected Music Type name. direction of the arrows.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory. You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 iPod威 control supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices. Some iPod威 software versions may not fully support the iPod威 control features. Please visit Apple’s website for software updates. NOTE: • If the radio has a USB port, refer to the appropriate Uconnect™ Multimedia radio User’s Manual for iPod威 or external USB device support capability.
248 UNDERSTANDING YOUR INSTRUMENT PANEL not available in the glove compartment, route the cable Using This Feature away from the lid latch and in a place that will allow the By using iPod cable or external USB device to connect to USB port: lid to close without damaging the cable. Once the audio device is connected and synchronized to • The audio device can be played on the vehicle’s sound system, providing metadata (artist, track title, album, the vehicle’s iPod威/USB/MP3 control system (iPod威 or etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. • Jump backward in the current track by pressing and holding the << RW button. Holding the << RW button long enough will jump to the beginning of the current track. Play Mode When switched to iPod威/USB/MP3 control mode, the iPod威 or external USB device automatically starts Play • Jump forward in the current track by pressing and holding the FF >> button. mode.
250 UNDERSTANDING YOUR INSTRUMENT PANEL to the next screen of data for that track. Once all screens have been viewed, the last INFO button press will go back to the play mode screen on the radio. device, or press the VR button and say ⬙Shuffle ON⬙ or ⬙Shuffle Off⬙. If the RND icon is showing on the radio display, then the shuffle mode is ON. • Pressing the REPEAT button will change the audio device mode to repeat the current playing track or press the VR button and say ⬙Repeat ON⬙ or ⬙Repeat Off⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable. • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • During all List modes, the iPod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (counterclockwise) to get to the track faster.
252 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 or external USB device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威 or external USB device, or connections to the iPod威 or external USB device in the vehicle, can cause damage to the device and/or to the connectors.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 2. After the ⬙Ready⬙ prompt and the following beep, say STEERING WHEEL AUDIO CONTROLS — IF ⬙Setup⬙, then ⬙Select Audio Devices⬙. EQUIPPED The remote sound system controls are located on the rear 3. Say the name of the audio device or ask the surface of the steering wheel. Reach behind the wheel to Uconnect™ phone system to list audio devices. access the switches.
254 UNDERSTANDING YOUR INSTRUMENT PANEL The right hand control is a rocker type switch with a The button located in the center of the left hand control pushbutton in the center. Pressing the top of the switch will tune to the next pre-set station that you have will increase the volume, and pressing the bottom of the programmed in the radio pre-set pushbuttons. switch will decrease the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 NOTE: If you experience difficulty in playing a particuCD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
256 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Climate Control System allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel below the radio. NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Mix Mode Air is directed through the outlets in the instrument Air is directed through the floor, defrost and side panel. These outlets can be adjusted to direct airflow. window demist outlets. This setting works best in cold or snowy conditions that require extra heat at Bi-Level Mode the windshield. This setting is good for maintaining Air is directed through the panel and floor outlets. comfort, while reducing moisture on the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Recirculation Control Press this button to choose between outside air intake or recirculation of the air inside the vehicle. A LED will illuminate when you are in Recirculation mode. Only use the Recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool the interior rapidly upon initial start-up in very hot or humid weather.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Economy Mode MAX A/C If ECONOMY mode is desired, press the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired temperature. For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recirculated. Air Conditioning Operation Push this button to engage the Air Conditioning (A/C).
UNDERSTANDING YOUR INSTRUMENT PANEL 261 • When occupants in the vehicle select an Auto mode operation, Auto blower operation is set by using rotary knobs on the control unit and a comfort temperature setting by using the temperature up and down buttons. • The system provides set-and-forget operation for optimum comfort and convenience. 4 • The system can be controlled manually, if desired.
262 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • It is not necessary to move the temperature settings for 1. Position the MODE control knob to the Auto position cold or hot vehicles. The system automatically adjusts on the Automatic Temperature Control (ATC) Panel. the temperature, mode and fan speed to provide 2. Position the BLOWER control knob in the Auto posicomfort as quickly as possible. tion on the ATC Panel. • The temperature can be displayed in U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 blower will engage immediately if the Defrost mode is The blower fan speed can be set to any fixed speed by selected, or by adjusting the blower control knob and adjusting the blower control knob. The fan will now operate at a fixed speed until additional speeds are setting the fan to any fixed speed. selected.
264 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In many temperature positions, the BI-LEVEL NOTE: While operating in the other modes, the system mode is designed to provide cooler air out of the panel will not automatically sense the presence of fog, mist or ice on the windshield. Defrost mode must be manually outlets and warmer air from the floor outlets. selected to clear the windshield and side glass. Floor Mode Air comes from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the RECIRCULATION control button. Recirculation mode should only be used temporarily. The recirculation LED will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the Recirculation mode LED and allow outside air into the vehicle.
266 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in fresh air with the blower setting in high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging and Frosting Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Operating Tips 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 273 ▫ Brake/Transmission Shift Interlock System . . 278 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 273 ▫ Six–Speed Automatic Transmission (5.7L Engine) — If Equipped . . . . . . . . . . . . 278 ▫ Automatic Transmission . . . . . . . . . . . . . . . 273 ▫ Extreme Cold Weather (Below –20°F Or ⫺29°C) . . . . . . . . . . . . . . . 274 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . .
270 STARTING AND OPERATING ▫ Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped . . . . . . . 292 ▫ Shifting Procedure . . . . . . . . . . . . . . . . . . . 296 䡵 Limited-Slip Differential . . . . . . . . . . . . . . . . . 298 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 299 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 299 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 䡵 Driving Through Water . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 271 ▫ Compact Spare Tire – If Equipped . . . . . . . . 325 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 335 ▫ Full Size Spare – If Equipped . . . . . . . . . . . . 326 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 336 ▫ Limited-Use Spare – If Equipped . . . . . . . . . 326 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 336 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 327 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . .
272 STARTING AND OPERATING 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 344 ▫ Common Towing Definitions . . . . . . . . . . . . 344 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 347 ▫ Over The Road Operation With Snowplow Attached . . . . . . . . . . . . . . . . . . . . . . . . . . 363 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 363 ▫ General Maintenance . . . . . . . . . . . . . . ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . .
STARTING AND OPERATING 273 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Normal starting of either a warm or cold engine is inside and outside mirrors, and fasten your seat belt. obtained without pumping or pressing the accelerator pedal. Turn the key fob to the START position and release The starter should not be operated for more than 15when the engine starts. If the engine fails to start within second intervals.
274 STARTING AND OPERATING Tip Start Feature Do not press the accelerator. Turn the ignition switch briefly to the START position and release it. The starter motor will continue to run but will automatically disengage when the engine is running. Extreme Cold Weather (Below –20°F or ⫺29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended.
STARTING AND OPERATING 275 WARNING! (Continued) • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “Jump Starting” in “What To Do In Emergencies” for further information. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released.
276 STARTING AND OPERATING The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. WARNING! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
STARTING AND OPERATING 277 WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the key fob. Once the key fob is removed, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
278 STARTING AND OPERATING Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Interlock which requires the shift lever to be placed in PARK before the ignition switch can be turned to the LOCK/ OFF position. The key fob can only be removed from the ignition when the ignition is in the LOCK/OFF position, and once removed the shift lever is locked in PARK.
STARTING AND OPERATING 279 The transmission shift lever has only PARK, REVERSE, NEUTRAL, and DRIVE shift positions. Manual downshifts can be made using the Electronic Range Select (ERS) shift control (refer to “Electronic Range Select (ERS)” in this section). Pressing the ERS (-/+) switches on the shift lever while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
280 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever clockwise without first pulling it toward you after you have placed it in PARK. Make sure the transmission is in PARK before leaving the vehicle. • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed.
STARTING AND OPERATING 281 CAUTION! • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • Look at the shift lever position display and verify that it indicates the PARK position.
282 STARTING AND OPERATING WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can result in severe transmission damage.
STARTING AND OPERATING 283 If the transmission operating temperature exceeds normal operating limits, the powertrain controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely hot, the “Transmission Temperature Warning Light” may illuminate and the transmission may downshift out of Overdrive until the transmission cools down.
284 STARTING AND OPERATING to operate. Limp Home Mode allows the vehicle to be NOTE: Even if the transmission can be reset, we recomdriven to an authorized dealer for service without dam- mend that you visit your authorized dealer at your aging the transmission. earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could In the event of a momentary problem, the transmission recur.
STARTING AND OPERATING 285 switch will activate ERS mode, display the current gear in To exit ERS mode, simply press and hold the ERS (+) the instrument cluster, and maintain that gear as the top switch until “D” is once again displayed in the shift lever available gear. Once in ERS mode, tapping ERS (-) or (+) position indicator in the instrument cluster. will change the top available gear. WARNING! Do not downshift for additional engine braking on a slippery surface.
286 STARTING AND OPERATING Overdrive Operation The automatic transmission includes an electronically controlled Overdrive (fifth and sixth gears). The transmission will automatically shift into the Overdrive gear if the following conditions are present: • the shift lever is in the DRIVE position, HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
STARTING AND OPERATING 287 The “TOW/HAUL Indicator Light” will illuminate in the instrument cluster to indicate that TOW/HAUL mode has been activated. Pressing the switch a second time restores normal operation. If the TOW/HAUL mode is desired, the switch must be pressed each time the engine is started. transmission fluid and engine coolant are warm [usually after 1 to 3 miles (1.6 to 4.8 km) of driving].
288 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED Four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further information. Manually Shifted Transfer Case – If Equipped The transfer case provides four mode positions.
STARTING AND OPERATING 289 When operating your vehicle in 4L, the engine speed is approximately three times that of the 2H or 4H positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the drivetrain.
290 STARTING AND OPERATING For additional information on the appropriate use of each 4L transfer case mode position, see the information below: Four-Wheel Drive Low Range - This range locks the front and rear driveshafts together forcing the front and rear 2H wheels to rotate at the same speed. Additional traction Rear-Wheel Drive High Range - This range is for normal and maximum pulling power for loose, slippery road street and highway driving on dry hard surfaced roads. surfaces only.
STARTING AND OPERATING 291 2H or 4H ⇔ 4L • Shifting into or out of 4L is possible with the vehicle With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift completely stopped, however difficulty may occur due the transmission into NEUTRAL. While the vehicle is to the mating clutch teeth not being properly aligned. coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer Several attempts may be required for clutch teeth case lever firmly to the desired position.
292 STARTING AND OPERATING Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
STARTING AND OPERATING 293 desired position. Refer to “Shifting Procedure” for specific shifting instructions. The 4WD LOCK and 4WD LOW positions are designed for loose, slippery road surfaces only. Driving in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. NOTE: The transfer case NEUTRAL position is selected by pressing the recessed button located on the lower left hand corner of the 4WD Control Switch.
294 STARTING AND OPERATING 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. WARNING! Always engage the parking brake when powering down the vehicle if the “SVC 4WD Warning Light” is illuminated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met.
STARTING AND OPERATING 295 Proper operation of four-wheel drive vehicles depends For additional information on the appropriate use of each on tires of equal size, type and circumference on each transfer case mode position, see the information below: wheel. Any difference in tire size can cause damage to the 2WD drivetrain. Rear Wheel Drive High Range - This range is for normal Because four-wheel drive provides improved traction, street and highway driving on dry, hard surfaced roads.
296 STARTING AND OPERATING N • If all the requirements to select a new transfer case Neutral - This range disengages both the front and rear position have been met, the current position indicator driveshafts from the powertrain. To be used for flat light will turn OFF, the selected position indicator light towing behind another vehicle. Refer to “Recreational will flash until the transfer case completes the shift.
STARTING AND OPERATING 297 NOTE: The four-wheel drive system will not allow shifts between 2WD/4WD LOCK if the front and/or rear wheels are spinning (no traction). In this situation, the selected position indicator light will flash and the original position indicator light will remain ON. At this time, reduce speed and stop spinning the wheels to complete the shift. 2. Shift the transmission into NEUTRAL. 3. While still rolling, rotate the transfer case control switch to the desired position. 4.
298 STARTING AND OPERATING NOTE: • If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift, then the desired position indicator light will flash continuously while the original position indicator light is ON, until all requirements have been met. surfaces, however, the differential delivers more of the driving effort to the rear wheel having the better traction.
STARTING AND OPERATING 299 Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a road or in a turn. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull erratically to the right or left.
300 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 301 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
302 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 303 system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticidoes not in any way damage the steering system. pated. Coordinate inspection efforts through an authoWARNING! rized dealer. Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
304 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied, the engine is off and the key fob is removed from the ignition switch.
STARTING AND OPERATING 305 NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
306 STARTING AND OPERATING CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle.
STARTING AND OPERATING 307 Four-Wheel Anti-Lock Brake System WARNING! The Four-Wheel Anti-Lock Brake System contains sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure.
308 STARTING AND OPERATING ABS Warning Light The ABS includes an amber warning light. When the light is illuminated, the ABS is not functioning. The system reverts to standard, non-anti-lock brakes. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 309 TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
310 STARTING AND OPERATING compact spare tires have the letter “T” or “S” molded • High flotation tire sizing is based on U.S. design into the sidewall preceding the size designation. Exstandards and it begins with the tire diameter molded ample: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING 311 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
312 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 313 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
314 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 315 This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section.
316 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcusengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity. For example, if “XXX” and number and size of occupants.
STARTING AND OPERATING 317
318 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 319 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar or rear edge of the driver’s side door.
320 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 321 Tire Inflation Pressure – 4500/5500 With Steel Carcass Ply Tires This type of tire utilizes steel cords in the sidewall. As such, they cannot be treated like normal light truck tires. Adjusting tire pressure must be performed by personnel trained, supervised and equipped accordingly.
322 STARTING AND OPERATING 4500/5500 Tire Inflation
STARTING AND OPERATING 323 When adjusting inflation pressure to a tire and wheel Tire Pressures For High Speed Operation assembly mounted on a vehicle, use a Remote Mount The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condiAutomatic Inflation Kit or see your authorized dealer.
324 STARTING AND OPERATING Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision resulting in serious injury or death. Always use radial ply tires in sets of four (or six, in case of trucks with dual rear wheels). Never combine them with other types of tires.
STARTING AND OPERATING 325 CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact, full size or limited-use temporary spare installed. Damage to the vehicle may result. Compact Spare Tire – If Equipped The compact spare is for temporary emergency use only.
326 STARTING AND OPERATING your original equipment tire, replace (or repair) the Full Size Spare – If Equipped The full size spare is for temporary emergency use only. original equipment tire and reinstall on the vehicle at the This tire may look like the original equipped tire on the first opportunity. front or rear axle of your vehicle, but it is not. This spare WARNING! tire may have limited tread life.
STARTING AND OPERATING 327 Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information.
328 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point. WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
STARTING AND OPERATING 329 Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall. See the Tire Sizing Chart example found in the Tire Safety Information section of this manual for more information relating to the Load Index and Speed Symbol of a tire. It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.
330 STARTING AND OPERATING WARNING! (Continued) • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision resulting in serious injury or death. • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control resulting in serious injury or death.
STARTING AND OPERATING 331 CAUTION! (Continued) CAUTION! (Continued) • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage. Remove the damaged parts of the chain before further use. • Install chains as tightly as possible and then retighten after driving about 1/2 mi (0.8 km).
332 STARTING AND OPERATING • On 4X2 vehicles, class “U” snow chains are permitted on the rear wheels only of vehicles equipped with LT245/70R17, LT265/70R17, and LT235/80R17 size tires. SNOW TIRES Some areas of the country require the use of snow tires during the winter. All season tires can be identified by the M+S designation on the tire sidewall.
STARTING AND OPERATING 333 While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. Refer to the “Maintenance Schedule” for the proper maintenance intervals. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
334 STARTING AND OPERATING NOTE: On Canadian vehicles only, if your vehicle is equipped with All-Season type tires on the front and On/Off Road type tires mounted on the rear, do not use a front to back rotation pattern. Instead, rotate your tires side to side at the recommended intervals. The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires.
STARTING AND OPERATING 335 CAUTION! (Continued) • When replacing a flat, the spare tire may have to be remounted on the rim or installed at a different location to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the vehicle. For example, if the spare is used to replace an outer rear tire it will have to be remounted on the rim so that the wheel is dished inward. That way the tread design of asymmetrical tires will maintain proper position.
336 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. CAUTION! Do not use gasolines containing Methanol or E-85 Ethanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components.
STARTING AND OPERATING 337 If a Non-FFV vehicle is inadvertently fueled with E-85 More extensive repairs will be required for prolonged fuel, the engine will have some or all of these symptoms: exposure to E-85 fuel. • operate in a lean mode MMT In Gasoline MMT is a manganese containing metallic additive that is • OBD II “Malfunction Indicator Light” on blended into some gasoline to increase octane.
338 STARTING AND OPERATING Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING 339 CAUTION! (Continued) • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
340 STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. ADDING FUEL CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
STARTING AND OPERATING 341 WARNING! WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel to the vehicle when the engine is running. This is in violation of most state and federal fire regulations and may cause the MIL to turn on. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
342 STARTING AND OPERATING VEHICLE LOADING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Certification Label As required by National Highway Traffic Safety Admin- Payload istration regulations, your vehicle has a certification label The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the affixed to the driver’s side door or pillar. driver, all passengers, options and cargo.
STARTING AND OPERATING 343 Tire Size The tire size on the Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.
344 STARTING AND OPERATING Improper weight distributions can have an adverse effect To maintain warranty coverage, follow the requirements on the way your vehicle steers and handles and the way and recommendations in this manual concerning vethe brakes operate. hicles used for trailer towing. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
STARTING AND OPERATING 345 The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded.
346 STARTING AND OPERATING the trailer tongue that typically provides adjustable fric- safety. The addition of a friction/hydraulic sway control tion associated with the telescoping motion to dampen also dampens sway caused by traffic and crosswinds and any unwanted trailer swaying motions while traveling. contributes positively to tow vehicle and trailer stability.
STARTING AND OPERATING 347 Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed.
348 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) CHASSIS CAB 3500 5.7L HEMI威 V8 5-Speed Automatic Transmission 6.7L Cummins威 Turbo Diesel I-6 6-Speed Manual Transmission 6.
STARTING AND OPERATING 349 CHASSIS CAB 5500 6.7L Cummins威 Turbo Diesel I-6 6-Speed Manual Transmission 6.
350 STARTING AND OPERATING Never exceed the maximum tongue weight stamped on • The weight of any other type of cargo or equipment your trailer hitch. put in or on your vehicle • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
STARTING AND OPERATING 351 Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
352 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in PARK.
STARTING AND OPERATING 353 • Check for signs of tire wear or visible tire damage • An electronically actuated trailer brake controller is before towing a trailer. Refer to “Tires – General required when towing a trailer with electronically Information” in “Starting and Operating” for the actuated brakes. When towing a trailer equipped with proper inspection procedure. a hydraulic surge actuated brake system, an electronic brake controller is not required.
354 STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have a collision. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in a collision.
STARTING AND OPERATING 355 The user interface consists of the following: GAIN/ Brake Output Power Display Shows the current GAIN setting. lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes. The trailer and the vehicle’s brake lamps will come on This display may also be used to display diagnostic when either vehicle braking or manual trailer brakes are information, if needed. applied.
356 STARTING AND OPERATING GAIN Adjustment Buttons (+/-) Pressing these buttons will adjust the brake control power output to the trailer brakes in 0.5 increments. The GAIN setting can be increased to a maximum of 10 or decreased to a minimum of 0 (no trailer braking). GAIN The GAIN setting is used to set the trailer brake control for the specific towing condition and should be changed as towing conditions change. Changes to towing conditions include trailer load, vehicle load, road conditions and weather.
STARTING AND OPERATING 357 4. Press the UP or DOWN button on the steering wheel 5. Press the SELECT button and then press the UP or until System Setup appears on the screen. DOWN buttons until Trailer Brake Type appears on the screen.
358 STARTING AND OPERATING 6. Press the SELECT button and then press the UP or 8. In a traffic-free environment, tow the trailer on a dry, DOWN buttons until the proper Trailer Brake Type level surface at a speed of 20–25 mph (30–40 km/h) and appears on the screen. squeeze the manual brake control lever completely. 9. If the trailer wheels lockup (indicated by squealing tires), reduce the GAIN setting; if the trailer wheels turn freely, increase the GAIN setting.
STARTING AND OPERATING 359 CAUTION! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in damage to your vehicle, trailer, or other property. WARNING! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking.
360 STARTING AND OPERATING WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automotive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. NOTE: Using “TOW/HAUL” mode or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up.
STARTING AND OPERATING 361 Electronic Speed Control – If Equipped − Do not use in hilly terrain or with heavy loads. − Air Conditioning Turn off temporarily. − When using the speed control, if you experience speed SNOWPLOW drops greater than 10 mph (16 km/h), disengage until Snowplow Prep Packages are available as a factory installed option. These packages include components you can get back to cruising speed. necessary to equip your vehicle with a snowplow.
362 STARTING AND OPERATING WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in a collision. Do not expect that the airbag will perform as described earlier in this manual CAUTION! The “Lamp Out” indicator could illuminate if exterior lamps are not properly installed. Before Plowing • Check the runners and cutting edge for excessive wear. The cutting edge should be 1/4 to 1/2 in (6 cm to 1.2 cm) above ground in snow plowing position.
STARTING AND OPERATING 363 The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver, passengers, options, and cargo, must not exceed either the Gross Vehicle Weight (GVWR) or Gross Axle Weight (GAWR) ratings. These weights are specified on the Safety Compliance Certification Label on the driver’s side door opening. Maintain and operate your vehicle and snowplow equipment following the recommendations provided by the specific snowplow manufacturer.
364 STARTING AND OPERATING NOTE: During snowplow usage on vehicles equipped with outside temperature display, the display may show higher temperatures than the outside ambient temperature. The higher displayed temperature is due to blocked or reduced airflow to the underhood ambient temperature sensor caused by the snowplow.
STARTING AND OPERATING 365 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
366 STARTING AND OPERATING 5. Remove the key fob from the ignition switch. Recreational Towing – Two-Wheel Drive Models DO NOT flat tow this vehicle. Damage to the drivetrain 6. Install a suitable clamping device, designed for towwill result. ing, to secure the front wheels in the straight position. Recreational towing (for two-wheel drive models) is CAUTION! allowed ONLY if the rear wheels are OFF the ground.
STARTING AND OPERATING 367 Recreational Towing – Four-Wheel Drive Models NOTE: Both the manual shift and electronic shift transfer cases must be shifted into NEUTRAL (N) for recreational towing. Automatic transmissions must be shifted into PARK for recreational towing. Refer to the following for the proper transfer case NEUTRAL (N) shifting procedure for your vehicle. CAUTION! • Front or rear wheel lifts should not be used.
368 STARTING AND OPERATING Shifting Into NEUTRAL (N) – Manual Shift Transfer Case (If Equipped) Use the following procedure to prepare your vehicle for recreational towing. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL (N) position without first fully engaging the parking brake.
STARTING AND OPERATING 369 9. Repeat steps 7 and 8 with transmission in DRIVE. 10. Turn OFF the engine. 11. Firmly apply the parking brake. 12. Shift the transmission into PARK. CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL (N) and the engine running. With the transfer case in NEUTRAL (N) ensure that the engine is OFF prior to shifting the transmission into PARK. 13. Remove the key fob from the ignition switch.
370 STARTING AND OPERATING 7. Shift the transmission into PARK. 8. Release the brake pedal. 9. Disconnect vehicle from the tow vehicle. 10. Start the engine. 11. Press and hold the brake pedal. 12. Release the parking brake. 13. Shift the transmission into gear, release the brake pedal, and check that the vehicle operates normally.
STARTING AND OPERATING 371 CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing to prevent damage to internal parts. light will blink while the shift is in progress. The light will stop blinking (stay on solid) when the shift to NEUTRAL is complete. 7. After the shift is completed and the NEUTRAL light stays on, release the NEUTRAL button. 1. Bring the vehicle to a complete stop. Shift automatic 8. Start the engine.
372 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL, ensure that the engine is OFF prior to shifting the transmission into PARK. 15. Remove the key fob from the ignition switch. 16. Attach the vehicle to the tow vehicle using a suitable tow bar. 17. Release the parking brake.
STARTING AND OPERATING 373 8. After the NEUTRAL button has been released, the Shifting Out Of NEUTRAL – Electronic Shift transfer case will shift to the position indicated by the Transfer Case (If Equipped) Use the following procedure to prepare your vehicle for selector switch. normal usage: NOTE: When shifting out of transfer case NEUTRAL, 1. Bring the vehicle to a complete stop, leaving it con- turning the engine OFF may be required to avoid gear nected to the tow vehicle. clash. 2.
374 STARTING AND OPERATING NOTE: • The ignition switch must be in the ON/RUN position • Steps 1 through 5 are requirements that must be met for a transfer case shift to take place and for the prior to pressing the transfer case NEUTRAL button position indicator lights to be operable. If the ignition and must continue to be met until the shift has been switch is not in the ON/RUN position, the shift will completed.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 376 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . 390 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 376 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 392 ▫ 3500 Models — If Equipped . . . . . . . . . . . . . 377 䡵 Emergency Tow Hooks — If Equipped . . . . . . 393 ▫ Preparations For Jacking . . . . . . . . . . . . . . . 378 䡵 Shift Lever Override . . . . . . . . . . . . . .
376 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS JACKING AND TIRE CHANGING The Hazard Warning flasher switch is located on the WARNING! upper switch bank just below the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flashers.
WHAT TO DO IN EMERGENCIES 377 WARNING! (Continued) • The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. 3500 Models — If Equipped The jack and jack tools are stored under the front passenger seat. Lift the flap on the side of the seat for access.
378 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. 4500/5500 Models These vehicles do not come equipped with a jack. Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.
WHAT TO DO IN EMERGENCIES 379 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
380 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. If equipped, remove the spare wheel, jack, and tools from storage. 2.
WHAT TO DO IN EMERGENCIES 381 6 Front Jacking Locations Rear Jacking Location When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. Connect the jack tube extension and lug wrench.
382 WHAT TO DO IN EMERGENCIES 4. By rotating the wheel wrench clockwise, raise the 6. Using the wheel wrench, finish tightening the nuts vehicle until the wheel just clears the surface. using a crisscross pattern. The correct nut tightness is 135 ft lbs (183 N·m) torque for single rear wheel (SRW) WARNING! models and 145 ft lbs (197 N·m) for dual rear wheel models.
WHAT TO DO IN EMERGENCIES 383 8. Lower the jack to its fully closed position. If the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. Stow the replaced tire, jack, and tools as previously described. 9. Adjust the tire pressure when possible. CAUTION! Use extreme caution when removing the front and rear center caps. Damage can occur to the center cap and/or the wheel if screwdriver type tools are used.
384 WHAT TO DO IN EMERGENCIES models use the blade on the end of the lug wrench to pry Replace the wheel skins first using a rubber mallet. When the caps off. The wheel skin can now be removed. replacing the hub caps, tilt the cap retainer over the lug nut bolt circle and strike the high side down with a CAUTION! rubber mallet. Be sure that the hub caps and wheel skins are firmly seated around the wheel. • Use a back and forth motion to remove the hub cap.
WHAT TO DO IN EMERGENCIES 385 Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to correctly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. NOTE: When installing a spare tire (if equipped) as part of a dual rear wheel end combination, the tire diameter of the two individual tires must be compared.
386 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: Tightening Pattern (10 Studs) Tightening Pattern (8 Studs) 1. Tighten the wheel nuts in the numbered sequence to a snug fit.
WHAT TO DO IN EMERGENCIES 387 bolt holes in the wheels becoming elongated. This is especially important during the first few hundred miles/ kilometers of operation to allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recommended torque. Tighten the nuts to It is recommended that wheel stud nuts be kept torqued final torque in increments. Progress around the bolt to specifications at all times.
388 WHAT TO DO IN EMERGENCIES To Stow The Flat Or Spare — If Equipped pack. Jump-starting can be dangerous if done improperly Refer to Upfitters Body Builders Guide for information so please follow the procedures in this section carefully. on stowing your spare tire (if equipped). NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and HOISTING A conventional floor jack may be used at the jacking precautions. locations.
WHAT TO DO IN EMERGENCIES 389 Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.
390 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 391 WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle.
392 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between DRIVE/1st and REVERSE while applying slight pressure to the accelerator. CAUTION! • Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles.
WHAT TO DO IN EMERGENCIES 393 WARNING! WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. • Chains are not recommended for freeing a stuck vehicle.
394 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: 1. Firmly set the parking brake. 2. Turn the ignition switch to the ON/RUN position without starting the engine. 3. Tilt the steering wheel to the full up position. 4. Press and maintain firm pressure on the brake pedal. 5.
WHAT TO DO IN EMERGENCIES 395 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the transmission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational Towing” in the “Starting and Operating” section.
396 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws applying to vehicles under tow must be observed.
WHAT TO DO IN EMERGENCIES 397 Two-Wheel Drive Models If the transmission is not operable, or the vehicle must be The manufacturer recommends towing your vehicle with towed faster than 30 mph (48 km/h) or farther than all four wheels OFF the ground using a flatbed. 15 miles (24 km), tow with the rear wheels OFF the ground.
398 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 401 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 408 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 402 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 408 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 402 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . 409 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
400 MAINTAINING YOUR VEHICLE ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 414 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 442 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 417 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 443 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 423 ▫ Dual Or Quad Headlamp/Front Park And Turn Signal – If Equipped . . . . . . . . . . . . . . 443 ▫ Rear Axle And 4X4 Front Driving Axle Fluid Level . . . .
MAINTAINING YOUR VEHICLE 401 ENGINE COMPARTMENT — 5.
402 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 403 the SELECT button to turn off the message. If the Normally, the OBD II system will be ready. The OBD II problem continues, the message will appear the next time system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacethe vehicle is started. ment. If the OBD II system should be determined not A loose, improperly installed, or damaged fuel filler cap ready for the I/M test, your vehicle may fail the test.
404 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a. The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
MAINTAINING YOUR VEHICLE 405 DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.
406 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 407 NOTE: Under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.
408 MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils if the recommended oil quality requirements are met and the recommended maintenance intervals for oil and filter changes are followed. Materials Added To Engine Oil The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives.
MAINTAINING YOUR VEHICLE 409 WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
410 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. • Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling.
MAINTAINING YOUR VEHICLE 411 Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
412 MAINTAINING YOUR VEHICLE NOTE: Use only manufacturer approved A/C System Body Lubrication Sealers, Stop Leak Products, Seal Conditioners, Compres- Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, sor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE 413 The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant such as MOPAR威 Lock Cylinder Lubricant or equivalent directly into the lock cylinder. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots.
414 MAINTAINING YOUR VEHICLE exceeds the temperature range of your climate. This Exhaust System rating information can be found on most washer fluid The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust containers. system. The washer fluid reservoir will hold a full gallon of fluid If you notice a change in the sound of the exhaust system; when the Low Washer Fluid Light illuminates.
MAINTAINING YOUR VEHICLE 415 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
416 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE 417 Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.
418 MAINTAINING YOUR VEHICLE Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Use only the manufacturer’s recommended engine coolant (antifreeze). Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
MAINTAINING YOUR VEHICLE 419 Please review these recommendations for using Hybrid Please note that it is the owner’s responsibility to mainOrganic Additive Technology (HOAT) engine coolant tain the proper level of protection against freezing according to the temperatures occurring in the area where (antifreeze). When adding engine coolant (antifreeze): the vehicle is operated.
420 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 421 2. Lift and remove the plastic dipstick from the reservoir 3. Check the coolant level on the dipstick. neck. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing engine coolant (antifreeze).
422 MAINTAINING YOUR VEHICLE of this. As long as the engine operating temperature is • Do not overfill the coolant recovery bottle. satisfactory, the coolant bottle need only be checked once • Check engine coolant (antifreeze) freeze point in the a month. radiator and in the coolant recovery bottle.
MAINTAINING YOUR VEHICLE 423 • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
424 MAINTAINING YOUR VEHICLE With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Use only the manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. WARNING! • Use only manufacturer’s recommended brake fluid.
MAINTAINING YOUR VEHICLE 425 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
426 MAINTAINING YOUR VEHICLE fill hole on the front axle. The fluid level should be level Refer to the “Maintenance Schedule” for the proper maintenance intervals. with the bottom of the fill hole on the rear axle. Drain And Refill Lubricant Selection On 4500/5500 vehicles, remove the lower bolt to drain Refer to “Fluids, Lubricants, and Genuine Parts” in the axle fluid. “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 427 Transfer Case Automatic Transmission Drain And Refill Selection Of Lubricant Refer to the “Maintenance Schedule” for the proper It is important that the proper lubricant is used in the maintenance intervals. transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transLubricant Selection mission fluid.
428 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will require more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 429 NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be 3. Fully apply the parking brake and press the brake between the two “COLD” (lower) holes on the dipstick pedal. with the fluid at approximately 70°F (21°C) (room tem4. Place the shift lever momentarily into each gear posi- perature). If the fluid level is correctly established at tion ending with the lever in PARK.
430 MAINTAINING YOUR VEHICLE To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Appearance Care And Protection From Corrosion Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE 431 The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap and rinse the panels completely with clear water.
432 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once • If a lot of driving is done on gravel roads, consider a month. mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE 433 CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s protective finish. Only MOPAR威 Wheel Cleaner or equivalent is recommended. • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove stain.
434 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 435 Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements.
436 MAINTAINING YOUR VEHICLE otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
MAINTAINING YOUR VEHICLE 437 Cavity Cartridge Fuse J07 30 Amp Pink J08 J10 J11 J12 J13 J14 J15 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink 60 Amp Yellow 20 Amp Blue 40 Amp Green Mini Fuse Description Antilock Brakes Valve/Stability Control System Power Seat Cavity Cartridge Fuse J17 40 Amp Green J18 20 Amp Blue Sway Bar Module – If Equipped Transfer Case Module J19 Rear Defroster J21 Main Ignition Off Draw (IOD) Fuse Trailer Tow Lamps/ Park Lamps Front Blower J22 J20 M1 M5 Mini Fuse Desc
438 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse M6 Mini Fuse 20 Amp Yellow M7 20 Amp Yellow M8 20 Amp Yellow 20 Amp Yellow 15 Amp Blue M9 M10 M11 10 Amp Red Description Power Outlet (Instrument Panel or Front Console)/Rain Snsr Power Outlet (Rear Console or Center Seat) Front Heated Seat & Steering Wheel Rear Heated Seats Hands Free Module/ Vanity Lamp/ Universal Garage Door Opener Module Climate Control System Cavity Cartridge Fuse M12 M13 M14 M15 Mini Fuse 30 Amp Green 20 Amp Yellow 20 Am
MAINTAINING YOUR VEHICLE 439 Cavity Cartridge Fuse M16 M18 M19 M20 M21 M22 M23 Mini Fuse 10 Amp Red 15 Amp Blue 25 Amp Natural 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red Description Airbag Module Cavity Cartridge Fuse M25 Mini Fuse 20 Amp Yellow Center Stop Lamp M26 Automatic Shutdown 1 and 2 Instrument Cluster Interior Lighting /Sw Steering Wheel/Sw Bank Automatic Shutdown 3 Horns (Low/High) – Right Horns (Low/High) – Left M27 M28 M29 M30 M31 M32 10 Amp Red 10 Amp Red 15 Amp Blue 10 Amp Red
440 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse M33 M34 M35 M36 Mini Fuse 10 Amp Red 10 Amp Red 15 Amp Blue 20 Amp Yellow Description Powertrain Control Module Park Assist Module/ Climate Control System Module/IR Sensor/Compass Module Left Front & Rear Parklamps Power Outlet (Instrument Panel or Center Console) Cavity Cartridge Fuse M37 M38 Mini Fuse 10 Amp Red 25 Amp Natural Description Antilock Brakes/ Stability Control System Module/ Stoplamp Switch All Door Lock &Unlock CAUTION! • When ins
MAINTAINING YOUR VEHICLE 441 CAUTION! (Continued) • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected. • As an alternative to the above steps you may disconnect the negative cables from both batteries.
442 MAINTAINING YOUR VEHICLE (or check to see if the fuse is blown) to ensure that it is fully seated. When the IOD fuse is extracted, the instrument cluster in the odometer window will display ⬙NO FUSE.” LIGHT BULBS – Exterior Bulb No. Center High Mounted Stop Lamp (CHMSL) . . . . . 921 Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9145 Dual Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . H13 Quad Headlamp – Low Beam . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 443 BULB REPLACEMENT Dual Or Quad Headlamp/Front Park And Turn Signal – If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two plastic push-in rivets that secure the upper radiator seal to the radiator. 7.
444 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect electrical connectors. splash shield and lift the slide lock upward far enough to 11. Replace bulb(s) as necessary. disengage it from the lock post on the back of the front lamp unit housing. CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Always use the correct bulb size and type for replacement.
MAINTAINING YOUR VEHICLE 445 Fog Lamps – If Equipped Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 1. Reach under and behind the front bumper to access 1. Remove the two screws holding the housing/lens to the back of the front fog lamp housing. the body as shown. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise 1⁄4 turn to unlock the bulb from the housing. 4. Pull the bulb straight out from the housing.
446 MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wir- 3. Turn the desired bulb socket 1⁄4 turn and remove the ing harness to the body. socket and bulb from housing. 4. Pull the desired bulb straight from the socket.
MAINTAINING YOUR VEHICLE 447 CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. Cab Top Clearance Lamps – If Equipped 1. Remove the two screws from the top of the lamp. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing.
448 MAINTAINING YOUR VEHICLE 2. Rotate the socket 1⁄4 turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
MAINTAINING YOUR VEHICLE 449 FLUID CAPACITIES Fuel (Approximate) Standard Rear Tank Optional Midship Tank Engine Oil with Filter 5.7L Engine (SAE 5W-20, API Certified) Cooling System 5.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. U.S. Metric 52 Gallons 22 Gallons 197 Liters 83 Liters 7 Quarts 6.6 Liters 18.7 Quarts 17.
450 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 5.7L Engine Engine Oil Filter – 5.7L Engine Spark Plugs – 5.7L Engine Fuel Selection – 5.7L Engine Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5–Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 451 Chassis Component Automatic Transmission (5.7L Engine Only) Transfer Case Front and Rear Axle Fluid (4500/5500) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. GL-5 SAE 75W-90 Synthetic (MS-9763) or equivalent. MOPAR威 DOT 3 and SAE J1703 should be used or equivalent.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 456 E MAINTENANCE SCHEDULES CONTENTS 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 454 ▫ 5.7L Gas Engine . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 454 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE 5.7L Gas Engine The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating S conditions, such as dusty areas and very short trip C driving. Inspection and service should also be done H anytime a malfunction is suspected.
MAINTENANCE SCHEDULES 455 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated.
M A I N T E N A N C E 456 MAINTENANCE SCHEDULES Once A Month • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and S C add as needed. H E • Check all lights and other electrical items for correct D operation.
MAINTENANCE SCHEDULES 457 M 8,000 Miles (13,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ Lube the front drive shaft fitting (4x4 only). Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 16,000 Miles (26,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
M 458 MAINTENANCE SCHEDULES A I 24,000 Miles (39,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 24,000 miles (39 000 km). ❏ Lube the front drive shaft fitting (4x4 only). ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 459 M 40,000 Miles (65,000 km) or 30 Months Maintenance Service Schedule 48,000 Miles (78,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏ Lube the front drive shaft fitting (4x4 only). Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code ❏ Change the engine oil and engine oil filter.
M 460 MAINTENANCE SCHEDULES A I 56,000 Miles (91,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 56,000 miles (91 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
MAINTENANCE SCHEDULES 461 M 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). Replace the engine air cleaner filter. Replace the spark plugs. Lube the front drive shaft fitting (4x4 only). Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 462 MAINTENANCE SCHEDULES A I 72,000 Miles (117,000 km) or N T 54 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 72,000 miles (117 000 km). ❏ Lube the front drive shaft fitting (4x4 only). ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 463 M 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
M 464 MAINTENANCE SCHEDULES A I 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). N ❏ Replace the engine air cleaner filter. A ❏ Replace the spark plugs. N ❏ Inspect and replace PCV valve if necessary. C ❏ Lube the front drive shaft fitting (4x4 only).
MAINTENANCE SCHEDULES 465 M 104,000 Miles (169,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ Lube the front drive shaft fitting (4x4 only). ❏ Flush and replace the engine coolant at 104,000 miles (169 000 km) or 60 months whichever comes first. ❏ Flush and replace power steering fluid.
M 466 MAINTENANCE SCHEDULES A I 120,000 Miles (195,000 km) or 90 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). A N ❏ Lube the front drive shaft fitting (4x4 only). C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 467 M 128,000 Miles (208,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs. ❏ Lube the front drive shaft fitting (4x4 only). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the transfer case fluid.
M 468 MAINTENANCE SCHEDULES A I 144,000 Miles (234,000 km) or 108 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). A N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the C engine air cleaner filter; replace if necessary. E ❏ Lube the front drive shaft fitting (4x4 only).
MAINTENANCE SCHEDULES 469 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 475 ▫ Prepare For The Appointment . . . . . . . . . . . 473 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 475 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 473 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
472 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 479 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 479 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 479 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 473 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
474 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (866) 726–4636 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE 475 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
476 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 477 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
478 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC vemaintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency LLC vehicles.
IF YOU NEED CONSUMER ASSISTANCE 479 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
480 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
482 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . 418 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 158 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 408 Air Conditioner Maintenance . . . . . . . . . . . . . . . 411 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 256 Air Conditioning Controls . . . . . . . . . . . . . . . . . 256 Air Conditioning Refrigerant . . . . . . . . . . .
INDEX 483 Automatic Transmission Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . 429 Fluid and Filter Changes . . . . . . . . . . . . . . . 430 Fluid Level Check . . . . . . . . . . . . . . . . . 427,428 Fluid Type . . . . . . . . . . . . . . . . . . . . . . 427,451 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Special Additives . . . . . . . . . . . . . . . . . . . . . 428 Axle Fluid . . . . . . . . . . . . . . . . . . . . . . . 425,426,451 Axle Lubrication (Axle Fluid) . .
484 INDEX Carbon Monoxide Warning . . . . . . . . . . . . . . . 78,339 Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 93,255 Center High Mounted Stop Light . . . . . . . . . . . . 445 Center Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . 48 Center Seat Storage Compartment . . . . . . . . . . . . 176 Certification Label . . . . . . . . . . . . . . . . . . . . . . . 342 Chart, Tire Sizing . . . . . . . . . .
INDEX 485 Drain, Flush, and Refill . . . . . . Inspection . . . . . . . . . . . . . . . . Points to Remember . . . . . . . . Pressure Cap . . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Cupholders . . . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . 417 . . . . . . . . . . 420 . . . . . . . . . . 422 . . . . . . . . . . 419 . . . . . . . . . . 419 . . . . . . . 418,450 . . . . . . . . . . 172 . . . . . . . .
486 INDEX Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . 392 Hazard Warning Flasher . . . . . . . . . . . . . . . 376 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . 388 Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . 393 Emission Control System Maintenance . . . . . . . . . 403 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 408 Block Heater . . . . . . . . . . . . . .
INDEX 487 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . 428 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423 Power Steering . . . . . . . . . . . . . . . . . . . . . . 303 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 450 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . 150,200,445 Four Wheel Drive .
488 INDEX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . 91,180 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 275 High Beam/Low Beam Select (Dimmer) Switch . . 154 Hands-Free Phone (Uconnect™) . . . . . . . . . . . . . . 93 Hitches Trailer Towing . . . . . . . . . . .
INDEX 489 Information Center, Vehicle . . . . . . . . . . . . . . . . . 203 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 87 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 187,189 Instrument Panel and Controls . . . . . . . . . . . . . . 186 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 435 Integrated Power Module (Fuses) . . . . . . . . . . . . 435 Integrated Trailer Brake Controls . . . . . . . . . . . . . 354 Interior Appearance Care . . . . . . . . . . . . . . .
490 INDEX Interior . . . . . . . . . . . . . . . . . . . . . . . . . 150,164 Automatic Headlights . . . . . . . . . . . . . . . . . 148 Lights On Reminder . . . . . . . . . . . . . . . . . . 152 Brake Warning . . . . . . . . . . . . . . . . . . . . . . 197 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Bulb Replacement . . . . . . . . . . . . . . . . . 442,443 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . 198 Cap Top Clearance . . . . . . . . . . . . . . . . . . .
INDEX 491 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . 92 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7 . 409 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 404,476 .
492 INDEX Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 406,450 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 Change Interval . . . . . . . . . . . . . . . . . . . . . 406 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 408,450 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . 408 Identification Logo . . . . . . . .
INDEX 493 Sliding Rear Window . . . . . . . . . . . . . . . . . . 181 Steering . . . . . . . . . . . . . . . . . . . . . . . . 302,303 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 451 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 52 Programmable Electronic Features . . . . . . . . . . . . 216 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 21 Radial Ply Tires . . . . . . .
494 INDEX Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 79 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 81 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 476 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 309 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Safety, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . 78 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 243 Schedule, Maintenance . . . . .
INDEX 495 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 Automatic Transmission . . . . . . . . . . . . . . . . 278 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 290 Transfer Case, Shifting into Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . 368,370 Transfer Case, Shifting out of Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . 369,373 Short Message Service (SMS) . . . . . . . . . . . . . . . . 115 Shoulder Belt Upper Anchorage . . . . .
496 INDEX Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 408 System, Remote Starting . . . . . . . . . . . . . . . . . . . . 26 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 Temperature Control, Automatic (ATC) . . . . . . . . 260 Temperature Gauge, Engine Coolant . . . . . . . . . . 189 Tether Anchor, Child Restraint . . . . . . . . . . . . . 68,73 Text Messaging . . . . . . . . . . . . . . . . . . . . . . . . . 115 Tilt Steering Column . . . . . . . . . . . . .
INDEX 497 Tow Hooks, Emergency . . . . . . . . . . . . . . . . . . . 393 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344,395 24-Hour Towing Assistance . . . . . . . . . . . . . 107 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . 395 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Recreational . . . . . . . . . . . . . . . . . . . . . . . . 365 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Towing Assistance . . . . . . . . . . . . . . .
498 INDEX UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 246 Water Driving Through . . . . . . . . . . . . . . . . . . . . . 300 Uconnect™ (Hands-Free Phone) . . . . . . . . . . . . . . 93 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 479 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 432 Universal Consumer Interface (UCI) Connector . . . 246 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 432 Wheel Cover . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler Group LLC 12DD43-126-AD 4th Edition Printed in U.S.A.
