2012 RAM CARGO VAN 2012 OWNER’S MANUAL Chrysler Group LLC 12MZZ-126-AA 1199168 Ram Truck 1500-2500-3500 OM cover.indd 1 First Edition RAM CV C a r g o Va n Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents.
INTRODUCTION 5
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Remote Starting System — If Equipped . . . . . . . 29 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 29 䡵 Sentry Key威 . . . . . . . . . . . . . . . . . . . . . . . . . . 15 䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Sliding Side Door . . . . . . . . . . . . . . . . . . . . . . 41 ▫ Power Sliding Side Door — If Equipped . . . . . 42 ▫ Sliding Side Door Child Protection Lock . . . . . 46 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . 49 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 52 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Commercial Cargo Vehicles (No Factory Installed Rear Seats) — If Equipped . . . . . . . . . . 95 ▫ Restraining Infants And Small Children In Commercial Cargo Vehicles . . . . . . . . . . . . . . 97 䡵 Engine Break-In Recommendations . . . . . . . . . . 98 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 99 11 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similarly to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the Key Fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob. NOTE: Power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening the front door will cancel this feature. CAUTION! • If your vehicle battery becomes low or dead, your Key Fob will become locked in the ignition.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from the ignition and lock all doors when leaving the vehicle unattended. 15 is automatic, regardless of whether the vehicle is locked or unlocked. The system uses Key Fob with factory-mated Remote Keyless Entry (RKE) transmitter and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Light turns on during normal vehicle. Once a Key Fob is programmed to a vehicle, it vehicle operation (vehicle running for longer than 10 sec- cannot be reprogrammed to any other vehicle. onds), it indicates that there is a fault in the electronics. CAUTION! Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 provides both audible and visible signals, for the first Customer Key Programming Programming Key Fobs or RKE transmitters may be three minutes, the headlights will turn on, the park lamps and/or turn signals will flash and Vehicle Security Light performed at an authorized dealer. will flash repeatedly and the horn will sound.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE •Make sure the vehicle ignition system is ⬙OFF⬙ and the key is physically removed from the ignition. • Insert a valid key into the ignition switch and turn the key to the ON position. 2. Perform one of the following methods to lock the NOTE: • The driver’s door key cylinder and the liftgate button vehicle: on the RKE transmitter cannot arm or disarm the • Press LOCK on the interior power door lock switch Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm. ILLUMINATED ENTRY — IF EQUIPPED The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED Using The RKE Transmitter This system allows you to lock or unlock the doors and Three-button RKE transmitters will provide basic UNliftgate, and activate the Panic Alarm, optional power LOCK, LOCK and PANIC functions. liftgate, left power sliding door, and right power sliding door from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE (optional), power sliding doors, Remote Start feature (optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on LOCK. 21 Remote Unlock Doors And Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s side or twice to unlock all doors and liftgate. This will also turn on the Illuminated Entry system.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, the Remote NOTE: Pressing the LOCK button on the RKE transmitUnlock feature can be enabled or disabled by perform- ter while you are inside the vehicle will activate the ing the following steps: Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. 1. Perform this operation while standing outside the Press the UNLOCK button to deactivate the Vehicle vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Settings (Customer-Programmable Features)” in “Un- 5. Repeat these steps if you want to return this feature to derstanding Your Instrument Panel” for further infor- its previous setting. mation. NOTE: Pressing the LOCK button on the RKE transmit• For vehicles not equipped with the EVIC, perform the ter while you are in the vehicle will activate the Vehicle following steps: Security Alarm.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • When you turn off the Panic Alarm by pressing the PANIC button a second time, you may have to move closer to the vehicle due to the Radio Frequency (RF) noises of the system. If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. The liftgate cannot be opened from this switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is locked and the Vehicle Security Alarm is armed, pressing the LEFT Power Sliding Door button twice unlocks the power sliding door and disarms Vehicle Security Alarm. 25 Turn Off Flash Lights With RKE Lock — If Equipped This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Press and hold the UNLOCK button on a programmed Programming Additional Transmitters RKE transmitter for at least 4 seconds, but no longer than If you do not have a programmed RKE transmitter, 10 seconds. Then, press and hold the LOCK button while contact your authorized dealer for details. still holding the UNLOCK button. Transmitter Battery Replacement The recommended replacement battery is one CR2032 3. Release both buttons at the same time. battery. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. To assemble the RKE transmitter case, snap the two halves together. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. Separating RKE Transmitter 3. Remove and replace the battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). • Hood closed • Liftgate closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • NOTE: • The vehicle must be equipped with an automatic • transmission to be equipped with Remote Start.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 into the ignition switch and turn it to the ON/RUN NOTE: • If your power door locks were unlocked, Remote Start position, otherwise the engine will shut off at the end of 15-minute cycle. will automatically lock the doors. • The park lights will turn on and remain on during To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release Remote Start mode.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shutdowns while in the Cancel Remote Start Remote Starting will also cancel if any of the following Remote Start Mode, the system will not allow the Remote Start button to shut down the engine for two seconds occur: after receiving a valid Remote Start request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 If the lock knob is down when you shut either front door, If the lock knob is rearward when you shut either side the door will lock. Make sure the keys are not inside the sliding door, the door will lock. Make sure the keys are vehicle before closing the door. not inside the vehicle before closing the door.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accidentally locking your keys in the vehicle. Removing the Key Fob or closing the door will allow the locks to operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob. Front Passenger Power Door Switches 1 - Window Open/Close 2 - Power Door Locks 35 If you press the power door lock switch while the sliding door is open, the sliding door will lock.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Unlock Doors Automatically On Exit feature will not operate if there is any manual operation of the power door locks (lock or unlock). On vehicles equipped with the optional Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Power Window Lockout Switch — If Equipped The driver may lock out the rear power windows by depressing the bar switch just below the power window switches. Driver’s Power Window Switches NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening a front door will cancel this feature.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and a set of switches that lock and unlock all doors. The switches will operate only when the ignition switch is in the ON/RUN or ACC position and during power accessory delay.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped The front window switches may be equipped with an Auto-Down feature. Press the window switch past the detent, release, and the window will go down automatically. 39 Auto Up Feature With Anti-Pinch Protection — If Equipped The front driver and front passenger switches may be equipped with an Auto Up feature. Lift the window switch fully upward to the second detent, release, and the window will go up automatically.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Any impact due to rough road conditions may trigger the auto reverse function unexpectedly during autoclosure. If this happens, pull the switch lightly to the first detent and hold to close window manually. WARNING! There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the window path before closing. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the rear windows are open and buffeting occurs, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. SLIDING SIDE DOOR The sliding door may be opened from the inside or the outside.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Avoid high impacts against the door stop when open- Power Sliding Side Door — If Equipped The power sliding door may be opened or ing the door. This is very important when your vehicle closed manually or by using the buttons on the is parked on an incline as the door will slide faster in RKE transmitter, overhead console switch, or the downhill direction. rear door switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE for the driver and passengers. Pressing the switch once will open the power sliding door. If the switch is pressed while the door is under a power cycle, the door will reverse direction. 43 If the inside or outside door handles are used while the power sliding side door is activated, the power sliding door feature will be canceled and will go into manual mode.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If anything obstructs the power sliding side door while it is closing or opening, the door will automatically reverse to the closed or open position, provided it meets sufficient resistance. WARNING! You, or others, could be injured if caught in the path of the sliding door. Make sure the door path is clear before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. Within 10 seconds of the final cycle, press the HAZARD switch ON. 4. A single chime will sound to signify that you have successfully completed the programming. 2 You can turn the feature back on by repeating the previous procedure.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. To Engage the Child Protection Door Lock 1. Open the sliding side door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the Child Protection Door Lock system is engaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the RKE transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the power sliding door.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the liftgate, press the liftgate release handle NOTE: • After setting the Child Protection Door Lock system, located on the underside of the license plate bar and pull always test the door from the inside to make certain it the liftgate open with one fluid motion. is in the desired position. • The power sliding side door switches will not open the power sliding doors if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmitter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within five seconds, a second time, will close the liftgate. 49 2 The power liftgate may also be opened and closed by pressing the button located on the overhead console.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. When the RKE transmitter button is pressed and the Flash Lights feature is enabled, the tail lights will flash and several audible beeps will occur to signal that the liftgate is opening or closing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • There are also pinch sensors attached to the side of the • The power liftgate will not operate in temperatures liftgate opening. Light pressure anywhere along these below ⫺12°F (⫺24°C) or temperatures above 143°F strips will cause the liftgate to return to the open (62°C). Be sure to remove any buildup of snow or ice position. from the liftgate before pressing any of the power liftgate buttons.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All seat belt systems (except the driver’s and third row center) include Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat 53 NOTE: The Advanced Front Air Bags have a multistage inflator design.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. 4. Do not lean against the door or window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air Bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Supplemental Side Air Bag Inflatable Curtain (SABIC) and Seat-Mounted Side Air Bags (SAB) also need room to inflate. Do not lean against the door or window.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you under normal conditions. However, in a collision the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. 4. Position the lap belt across your thighs, below your abdomen.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Pull the strap down and secure the small latch plate of pushing anywhere on the anchorage. To move the anthe lap belt into the small buckle until you hear a “click”. chorage downward, squeeze the actuation buttons while simultaneously pushing down on the anchorage assemPosition the shoulder belt on your chest so that it is bly. comfortable and not resting on your neck.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE anytime a child safety seat is installed in a seating position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. 2 NOTE: The Active Head Restraints (AHR) may or may not deploy in the event of a front or side impact.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! 1. Grasp the deployed AHR from the rear seat. All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 2 1 — Downward Movement 2 — Rearward Movement 3 — Final Downward Movement To Engage Locking Mechanism
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. The AHR front soft foam and trim half should lock • For safety reasons, have the Active Head Restraints into the back decorative plastic half. checked by a qualified specialist at an authorized dealer. Enhanced Seat Belt Use Reminder System (BeltAlert姞) BeltAlert威 is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert威) to fasten their seat belts. The feature is active whenever the ignition is on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Light remains illuminated until the respective seat belts are fastened. The driver should instruct all other occupants to fasten their seat belts. If a front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), BeltAlert威 will provide both audio and visual notification.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and store it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon seat position.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle is equipped with Supplemental Seat- • Steering Wheel and Column Mounted Side Air Bags (SAB) to provide enhanced • Instrument Panel protection for an occupant during a side impact. The SABs are located in the outboard side of the front seats. • Supplemental Driver Side Knee Air Bag • Knee Impact Bolster NOTE: • Air Bag covers may not be obvious in the interior trim, • Driver Advanced Front Air Bag but they will open during air bag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors. The first stage inflator is triggered immediately during an impact that requires air bag deployment. This low output is used in less severe collisions.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bags (SAB) Supplemental Seat-Mounted Side Air Bags (SAB) may provide enhanced protection to help protect an occupant during a side impact. The SAB is marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. 75 WARNING! (Continued) • Do not use accessory seat covers or place objects between you and the side air bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Air Bags work with the Supplemental Driver Side Knee Air Bag and the passenger side knee bolster to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Also, the ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition is first turned on. After the self-check, the Air Bag Warning Light will turn off.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver Side Knee Air Bag. The trim cover separates and folds out of the way allowing the air bag to inflate to the full size. The air bag fully inflates in about 15 to 20 milliseconds. The Supplemental Driver Side Knee Air Bag gas is vented through small vent holes in the side of the air bag. 79 in about 10 milliseconds.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are not belted and seated properly, or if items are positioned in the area where the side curtain air bag inflates. This especially applies to children. The side curtain air bag is only about 3-1/2 in (9 cm) thick when it is inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 If A Deployment Occurs • As the air bags deflate, you may see some smoke-like The Advanced Front Air Bags are designed to deflate particles. The particles are a normal by-product of the immediately after deployment. process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the NOTE: Front and/or side air bags will not deploy in all skin, eyes, nose, or throat. If you have skin or eye collisions.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat including your trim cover and cushion needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR. 85 WARNING! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rearwardfacing or forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 in the vehicle by the lap/shoulder belt or the LATCH • The lap portion should be low on the hips and as snug child restraint anchorage system. Refer to “Lower Anas possible. chors and Tether for CHildren (LATCH)”. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward-facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing The Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector, and a means for adjusting the tension in the strap.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing The LATCH-Compatible Child Restraint NOTE: • When using the LATCH attaching system to install a System Each vehicle, except commercial cargo vehicles, child restraint, please ensure that all seat belts not is equipped with the child restraint anchorage being used for occupant restraints are stowed and out system called LATCH, which stands for Lower of reach of children. It is recommended that before Anchors and Tether for CHildren.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Installing the Lower Attachments: 1. The vehicle lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback. 2 LATCH Anchorages (Third Row 60/40 Anchorages Shown) LATCH Anchorages (Second Row Anchorages Shown) 2. Loosen the adjusters on the lower child restraint attachment straps (reference the child restraint seat instructions) to ease the installation.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: It is recommended to loosen the top tether strap Installing the Top Tether Strap and route it loosely prior to securing the lower anchors so (with either Lower Anchors or Vehicle Seat Belt): the top tether strap is not trapped between the vehicle 1. Route the top tether strap under the adjustable head seat and child restraint. restraint between the steel posts. 3. Attach the lower child restraint attachment straps to 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 2 Rear Seat Tether Strap Mounting (Second Row Anchorage Shown) LATCH Anchorages (Third Row 60/40 Anchorage Shown)
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Installing The Child Restraint Using The Vehicle Seat Belts The seat belts in the passenger seating positions are equipped with an Automatic Locking Retractor (ALR) or a cinching latch plate to secure a Child Restraint System (CRS).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 then allow the belt to retract into the retractor. As the belt Transporting Pets retracts, you will hear a ratcheting sound. This indicates Air Bags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly the safety belt is now in the Automatic Locking mode. injured, or injure a passenger during panic braking or in 2. Finally, pull on any excess webbing to tighten the lap a collision.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! NEVER carry a child in a rear facing infant carrier in a vehicle without rear seats. In an accident, serious injury or death may occur from the deploying passenger airbag. This vehicle is equipped with a child restraint tether anchor located on the lower rear of the front passenger seat. Use this tether anchor to secure only forwardfacing child restraints equipped with an upper tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Restraining Infants And Small Children In • Children more than 40 lbs (18 kg) should be secured in Commercial Cargo Vehicles the passenger seat in a child restraint or beltThere are different sizes and types of restraints for positioning booster seat with the seat adjusted to the children from newborn size to the child almost large rear most position. Older children who do not use enough for an adult safety belt.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the tether strap under the head rest. NOTE: Ensure that the child restraint tether strap is centered between the headrest supports underneath the head rest. 4. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal anchor on the lower rear of the front passenger seat. 5. Following the child seat manufacturer’s instructions, tighten the child restraint tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 While cruising, brief full-throttle acceleration within the should be considered a normal part of the break-in and limits of local traffic laws contributes to a good break-in. not interpreted as an indication of difficulty. Wide-open throttle acceleration in low gear can be detriSAFETY TIPS mental and should be avoided. The engine oil installed in the engine at the factory is a Transporting Passengers high-quality energy conserving type lubricant.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Inside Day/Night Mirror — If Equipped . . . 112 ▫ Automatic Dimming Mirror — If Equipped . . 112 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . 113 ▫ Driver’s Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 114 ▫ Tilt Mirrors In Reverse (Available With Memory Seat Only) — If Equipped . . . . . . . .
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Phone Call Features . . . . . . . . . . . . . . . . . . 135 ▫ Heated Seats — If Equipped . . . . . . . . . . . . 163 ▫ Uconnect™ Phone Features . . . . . . . . . . . . . 138 ▫ Manual Front/Second Row Seat Adjuster . . . 166 ▫ Advanced Phone Connectivity . . . . . . . . . . . 142 ▫ Manual Reclining Seats — If Equipped . . . . . 167 ▫ Things You Should Know About Your Uconnect™ Phone . . . . . . . . . . . . . . . . . . . . 144 ▫ Head Restraints . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 䡵 Driver Memory Seat — If Equipped . . . . . . . . 192 ▫ Dimmer Controls . . . . . . . . . . . . . . . . . . . . 201 ▫ Setting Memory Positions And Linking RKE Transmitter To Memory . . . . . . . . . . . . . . . . 192 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 203 ▫ Easy Entry/Exit Seat (Available With Memory Seat Only) . . . . . . . . . . . . . . . . . . . 195 䡵 To Open And Close The Hood . . . . . . . . . . . . 196 䡵 Lights . . . . . . .
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Rain Sensing Wipers — If Equipped . . . . . . . 207 ▫ Parksense威 Warning Display . . . . . . . . . . . . 216 䡵 Tilt/Telescoping Steering Column . . . . . . . . . . 208 ▫ Parksense威 Display . . . . . . . . . . . . . . . . . . . 217 䡵 Heated Steering Wheel — If Equipped . . . . . . 209 ▫ Enabling/Disabling Parksense威 . . . . . . . . . . 220 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 210 ▫ Service The Parksense威 Rear Park Assist System . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 䡵 Overhead Consoles . . . . . . . . . . . . . . . . . . . . 227 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 ▫ Front Overhead Console . . . . . . . . . . . . . . . 227 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 239 ▫ Courtesy/Interior Lighting . . . . . . . . . . . . . 228 ▫ General Information . . . . . . . . . . . . . . . . . . 240 ▫ Sunglass Storage (Non-Sunroof Only) . . . . . .
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 244 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 244 ▫ Glove Compartments . . . . . . . . . . . . . . . . . 254 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 244 ▫ Door Trim Panel Storage . . . . . . . . . . . . . . . 255 䡵 Electrical Power Outlets — If Equipped . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 ▫ Super Console — If Equipped . . . . . . . . . . . 266 䡵 Rear Load-Leveling System — If Equipped . . . 270 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 268 䡵 Roof Luggage Rack — If Equipped . . . . . . . . . 271 ▫ Rechargeable Flashlight . . . . . . . . . . . . . . . . 268 ▫ Deploying The Crossbars . . . . . . . . . . . . . . . 272 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 269 䡵 Sun Screens — If Equipped . . . . . . . .
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse. 113 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: A light in the selected button will illuminate indicating the mirror is activated and can be adjusted. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Driver’s side power mirror preselected positions can be controlled by the optional Driver Memory Seat Feature. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tilt Mirrors In Reverse (Available With Memory Seat Only) — If Equipped Tilt Mirrors in Reverse provides automatic outside mirror positioning which will aid the drivers view of the ground rearward of the front doors. The driver’s outside mirror will move slightly downward from the present position when the vehicle is shifted into REVERSE. The driver’s outside mirror will then return to the original position when the vehicle is shifted out of REVERSE position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 3 Illuminated Mirror Rear Detection Zones BLIND SPOT MONITORING — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM detection zone covers approximately one lane • The BSM system detection zone DOES NOT change if on both sides of the vehicle (11 ft or 3.35 m). The zone your vehicle is towing a trailer. Therefore, visually starts at the outside rear view mirror and extends apverify the adjacent lane is clear for both your vehicle proximately 20 ft (6 m) to the rear of the vehicle. The BSM and trailer before making a lane change.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 3 Sensor Locations BSM Warning Light The BSM system notifies the driver of objects in the detection zones by illuminating the BSM warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “Modes Of Operation” for further information. The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc. However, occasionally the system may alert adjacent lanes. on such objects. This is normal operation and your vehicle does not require service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible alert the radio (if on) will also be muted.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone using simple voice commands (e.g., “Call” ѧ “Mike” ѧ “Work” or “Dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect™ Phone. Uconnect™ Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. 127 Voice Command Button Actual button location may vary with the radio. The individual buttons are described in the “Operation” section.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Voice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structure. Voice commands are required after most Uconnect™ Phone prompts. You will be prompted for a specific command and then guided through the available options. example, you can use the compound form voice command “Phonebook New Entry”, or you can break the compound form command into two voice commands: “Phonebook” and “New Entry”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Cancel Command • When prompted, after the beep, say “Pair a Device” At any prompt, after the beep, you can say “Cancel” and and follow the audible prompts. you will be returned to the main menu. However, in a • You will be asked to say a four-digit Personal Identifew instances the system will take you back to the fication Number (PIN), which you will later need to previous menu. enter into your mobile phone.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the Uconnect™ Phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “Advanced Phone Connectivity” in this section). Call By Saying A Name • Press the button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 After you are finished adding an entry into the phonebook, you will be given the opportunity to add more NOTE: Adding names to the Uconnect™ Phonebook is phone numbers to the current entry or to return to the recommended when the vehicle is not in motion. main menu. • Press the button to begin.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call a name from the Uconnect™ Phonebook or • Only the mobile phone’s phonebook is downloaded. downloaded Phonebook, follow the procedure in SIM card phonebook is not part of the Mobile phone“Call by Saying a Name” section. book. • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth威 wireless phone connection is deleted on the Uconnect™ Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • After the “Ready” prompt and the following beep, say mobile and a home number, but you can add “John Doe’s” work number later using the “Phonebook Edit “Phonebook Edit Entry”. Entry” feature. • You will then be asked for the name of the phonebook entry that you wish to edit. Delete Uconnect™ Phonebook Entry • Next, choose the number designation (home, work, NOTE: Editing phonebook entries is recommended mobile, or other) that you wish to edit.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE from the list, press the button while the • The Uconnect™ Phone will ask you to verify that you Uconnect™ Phone is playing the desired entry and say wish to delete all the entries from the phonebook. “Delete”. • After confirmation, the phonebook entries will be deleted. • After you enter the name, the Uconnect™ Phone will ask you which designation you wish to delete: home, • Note that only the phonebook in the current language work, mobile, other, or all.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 • To call one of the names in the list, press the Answer Or Reject An Incoming Call — No Call button during the playing of the desired name, and Currently In Progress When you receive a call on your mobile phone, the say “Call”. Uconnect™ Phone will interrupt the vehicle audio sysNOTE: The user can also exercise “Edit” or “Delete” tem, if on, and will ask if you would like to answer the operations at this point. button to accept the call. To reject the call.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when another call is in progress. Therefore, the user can Toggling Between Calls If two calls are in progress (one active and one on hold), only answer an incoming call or ignore it. button until you hear a single beep, indicatpress the Making A Second Call While Current Call Is In ing that the active and hold status of the two calls have Progress switched. Only one call can be placed on hold at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination To end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press button until you hear a single beep. and hold the Redial • Press the button to begin.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone Features Emergency Assistance If you are in an emergency and the mobile phone is reachable: Language Selection To change the language that the Uconnect™ Phone is using: • Pick up the phone and manually dial the emergency number for your area. • Press the button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Canada and 060 for Mexico). The number dialed may Towing Assistance not be applicable with the available mobile service and If you need towing assistance: area. • Press the button to begin. • If supported, this number may be programmable on • After the “Ready” prompt and the following beep, say button and say some systems. To do this, press the “Towing Assistance”. “Setup”, followed by “Emergency”.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your Uconnect™ Phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “Send”. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can Voice Mail Calling button and say, “3 7 4 6 # Send”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 The Uconnect™ Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ tones over the phone. Phone will not repeat a phone number before you dial it). NOTE: • You may not hear all of the tones due to mobile phone • Press the button to begin. network configurations. This is normal.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using The Mobile Phone Keypad You can dial a phone number with your mobile phone keypad and still use the Uconnect™ Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 mobile phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using Voice Command.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 from your Uconnect™ Phone paired mobile phone to the • When prompted, say “List Phones”. button Uconnect™ Phone or vice versa, press the • The Uconnect™ Phone will play the phone names of and say “Transfer Call”. all paired mobile phones in order from the highest to Connect Or Disconnect Link Between The the lowest priority.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the Uconnect™ Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. Things You Should Know About Your Uconnect™ Phone Uconnect™ Phone Tutorial To hear a brief tutorial of the system features, press the button and say “Uconnect™ Tutorial.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 You can either press the Uconnect™ Phone button to Voice Command restore the factory setting or repeat the words and • For best performance, adjust the rearview mirror to phrases when prompted by the Uconnect™ Phone. For provide at least 1⁄2 in (1 cm) gap between the overhead best results, the Voice Training session should be comconsole (if equipped) and the mirror.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather condition. • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • You can say “O” (letter “O”) for “0” (zero). • Even though the system is designed for users speaking in North American English, French, and Spanish ac- • Even though international dialing for most number combinations is supported, some shortcut dialing cents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. 147 SMS Uconnect™ Phone can read or send new messages on your phone. Read Messages: • Performance, such as audio clarity, echo, and loudness If you receive a new text message while your phone is to a large degree rely on the phone and network, and connected to Uconnect™ Phone, an announcement will not the Uconnect™ Phone.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Where are you? Send Messages: You can send messages using Uconnect™ Phone. To send 4. I need more direction. a new message: 5. L O L • Press the button. 6. Why • After the “Ready” prompt and the following beep, say 7. I love you “SMS Send” or “Send Message.” • You can either say the message you wish to send or say 8. Call me “List Messages.” There are 20 preset messages. 9. Call me later button while the To send a message, press the 10.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me Turn SMS Incoming Announcement ON/OFF Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming messages. • Press the button. • After the “Ready” prompt and the following beep, say “Setup, SMS Incoming Message Announcement,” you will then be given a choice to change it.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 3
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) 153 Voice Commands Alternate(s) Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no other pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the winbutton, listen dows are closed, and the heater/air conditioning fan is options, press the Voice Command set to low. for the beep, and say your command. button while the Pressing the Voice Command system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking. Please note the volume setting for this mode, you may say the following commands: Voice Command is different than the audio system.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Disc To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: Satellite Radio • “Track” (#) (to change the track) To switch to satellite radio mode, say “Sat” or “Satellite Radio”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE − “Continue” (to continue recording) • “Switch to system setup” − “Delete” (to delete the recording) • “Change to setup” 159 • “Play Memos” (to play previously recorded memos) • “Main menu setup” or — During the playback you may press the Voice • “Switch to setup” button to stop playing memos.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers the Uconnect™ Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 WARNING! Power Lumbar Switch • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE during a remote start. Refer to “Remote Starting System NOTE: Once a heat setting is selected, heat will be felt — If Equipped” in “Things To Know Before Starting Your within two to five minutes. Vehicle” for further information. When the HIGH-level setting is selected, the heater will provide a boosted heat level during the initial stages of Front Heated Seats There are two heated seat switches that allow the driver operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. When the HIGH-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal HIGH-level.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front/Second Row Seat Adjuster Both front seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. While sitting in the seat, pull up on the handle and slide the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 To recline, lean forward slightly, lift the lever, then push Manual Reclining Seats — If Equipped For models equipped with manual reclining seats, the back to the desired position and release the lever. Lean recline lever is located on the outboard side of the seat. forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 3 Push Button For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 WARNING! (Continued) • Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Active Head Restraint ensure that all cargo is secured, as loose cargo could contact the Active Head Restraint during sudden stops. Failure to follow this warning could cause personal injury if the Active Head Restraint is deployed.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints — Third Row The head restraint in the center position can be raised and lowered for tether routing. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. NOTE: Seat will not stow in the storage bin unless the armrests are raised. 4. Slide the storage bin locking mechanism to the “LOCK” position and then pull up on the storage bin latch to open the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 5. Pull upward on the seatback recliner lever located on The non-adjustable head restraint and seatback will fold the outboard side of the seat. automatically during the seat tumble. No additional actuation is necessary.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Folding Seatback Tumbled Second Row Seat The seat will automatically tumble into position for easy 6. Push the seat into the storage bin. storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. 3 WARNING! Seat In Storage Bin 7. Close the storage bin cover. In a collision, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Unstow Second Row Seats 1. Pull up on the storage bin latch to open the cover. 2. Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. 3. Lift the seatback to the full upright position. 4. Return the head restraint to its upright position, close the storage bin cover and slide the storage bin locking mechanism to the “Unlocked” position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Easy Entry Second Row The second row Stow ’n Go威 seats allow easy entry to the third row seat or rear cargo area. Pull up on the seatback recliner lever on the outboard side of the seat. Raising The Head Restraint 3. Pull up on the seatback recliner lever on the outboard side of the seat to fold head rest and seatback and tumble seat forward.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The seat will automatically fold into position for easy entry into the third row. WARNING! In the event of a collision you could be injured if the seat is not fully latched. Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. Manual Seat Adjuster While sitting in the seat, pull up on the handle and slide the seat forward or rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Easy Entry To fold the seat, lift the recliner lever to the full upward The Quad seats can be tilted forward for easy entry into position and push the seatback forward until it rests on the third row. With the Quad seat in the fold-flat position, the seat cushion. lift up on the easy entry lever located near the bottom of the seat and lift the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For passengers seated in the third row, there is a pull strap located on the outboard side of the seat near the bottom of the seat back. Third row passengers can pull on the strap and push the Quad seat forward for folding the seatback and accessing the easy entry lever. Pull Strap for Third Row Passengers 181 To provide additional space behind the second row seats, the seats can be folded forward.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull out the retainer strap from the sewn-in pocket Place the strap around the grab handle located on the located on the base of the seat cushion. B-Pillar. Before securing the strap, adjust the buckle for proper fit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Secure the retainer strap to the inside grab handle located on the B-Pillar. When not in use, store the strap in the sewn-in pocket located on the base of the seat cushion. Retainer Strap 183 WARNING! To reduce the risk of personal injury: • Retainer strap must always be securely attached to grab handle when seat is folded forward and vehicle is moving. • Never occupy the seat or the center seat behind a seat that has been folded forward.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removal Second Row Bench Seat — If Equipped The Quad seats can be removed if additional storage is While the bench seat does not stow in the floor, it is needed. With the seat in the easy entry position, lift the removable for added cargo space. cross beam forward and up to release the front anchor latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its Easy Out威 Rollers. 185 To reinstall the seat, align the seat into the detent positions on the floor.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Power Recline — If Equipped Third Row Power Folding Seat — If Equipped The power recline feature, located on the side of the seat A one-touch power folding seat switch is located in the cushion, adjusts the seatback angle forward/rearward left rear trim panel as part of a switch bank. for occupant comfort. NOTE: Lower the head restraint by pulling on the release strap marked “1” located on the outboard side of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 The switch is only functional when the liftgate is open Left and right third row seats can be folded individually and the vehicle is in PARK. or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel: 3 One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Lower the outboard head restraints by pulling on the NOTE: • Disconnect the center shoulder belt from the small release strap marked “1” located on the outboard side of buckle and lower the head restraints before attempting the head restraint. to fold/stow the power third row seats. • To abort seat operation while seat is in motion, press a different seat position selector switch to stop the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 3. Pull release strap marked “2” located on the rear of the 4. Pull release strap marked “3” to release the anchors. seat to lower the seatback.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull release strap marked “4” and tumble the seat rearward into the storage bin. Stowed Third Row Seat To Unfold Third Row Seats Release Strap “4” 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “2” to unlock the recliner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 3. Pulling strap “4” releases the seatback to return to its 2. To restore the seat to its upright position, lift up on the full upright position. seatback and push forward until the anchors latch. 4. Raise the head restraint to its upright position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. Your vehicle may have been delivered with two RKE transmitters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 3. Adjust the driver’s seat, recliner, and driver’s side- 10. Insert the ignition key and turn the ignition switch to view mirror to the desired positions. the ON position. 4. Adjust the brake and accelerator pedals to the desired 11. Select “Remote Linked to Memory” in the Electronic Vehicle Information Center (EVIC) and enter “Yes”. Refer positions. to “Electronic Vehicle Information Center (EVIC)/ 5.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press MEMORY button 1 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1. 2. Press and release MEMORY button 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to Step 3. To recall the memory setting for driver two, press 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features⬙ in “Understanding • Your Instrument Panel” for further information. Easy Entry/Exit Seat (Available With Memory Seat ONLY) This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Easy Entry/Easy Exit feature can be enabled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). If your vehicle is not equipped with an EVIC, your dealership can activate/deactivate this feature for you. For details, refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 3 Safety Lever Location Use the hood prop rod to secure the hood in the open position.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light and instrument panel operation. Headlights On With Wipers — If Equipped When your headlights are in the AUTO mode and the engine is running, the headlights will automatically turn on when the wiper system is also turned on.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60 or 90 seconds or not remain on. To change the timer setting, see your authorized dealer. The headlight delay time is programmable on vehicles equipped with an EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Dimmer Controls Interior Lighting On The dimmer switch is located next to the headlight Rotate the left dimmer control completely upward to the switch. second detent (extreme top position) to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate. Interior Lighting Off Rotate the left dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. Parade Mode (Daytime Brightness Feature) Rotate the left dimmer control to the first detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Multifunction Lever • Headlight Beams Low/High The multifunction lever is located on the left side of the • Flash-To-Pass (Optical Horn) steering column. • Front and Rear Wipers — Washer Functions Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Battery Protection This feature provides battery protection to avoid wearing down the battery if the headlights, parking lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • At driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 second between cycles (first detent), to a cycle every one second (fifth detent). Mist Feature Press the end of the multifunction lever inward (toward the steering column) to the first detent and release for a single wiping cycle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of the five intermittent wiper sensitivity settings to activate this feature.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Rain Sensing system has protective features for the • Remote Start Mode Inhibit — On vehicles equipped wiper blades and arms. It will not operate under the with Remote Starting system, Rain Sensing wipers are following conditions: not operational when the vehicle is in the remote start mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in serious injury or death. Tilt/Telescoping Lever To unlock the steering column, push the lever downward (toward the floor).
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel switch is located on the switch bank below the climate controls. Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator. NOTE: The engine must be running for the heated steering wheel to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 from the driver to provide improved position with the Press the switch rearward to move the pedals rearward steering wheel. (toward the driver). The switch is located on the left side of the steering • The pedals can be adjusted with the ignition OFF. column. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The Electronic Speed Control buttons are located on the right side of the steering wheel. Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The system should be turned off when not in use.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE decrease until the button is released. Release the button To Resume Speed To resume a previously set speed, push the RES (+) when the desired speed is reached, and the new set speed button and release. Resume can be used at any speed will be established. above 20 mph (32 km/h). Pressing the SET (-) button once will result in a 1 mph (2 km/h) decrease in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 On steep hills, a greater speed loss or gain may occur so PARKSENSE姞 REAR PARK ASSIST — IF it may be preferable to drive without Electronic Speed EQUIPPED The ParkSense威 Rear Park Assist system provides visual Control. and audible indications of the distance between the rear WARNING! fascia and a detected obstacle when backing up, e.g. during a parking maneuver.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 ParkSense姞 Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Distance (in/cm) Audible Alert Chime Display Message Greater than 79 in (200 cm) None Arcs Park Assist System ON None Radio Mute No WARNING ALERTS 79-39 in 39-25 in (200-100 cm) (100-65 cm) Single 1/2 Slow Second Tone Warning Object Warning Object Detected Detected 3 Solid 3 Slow (Continuous) Flashing Yes Yes NOTE: ParkSense威 will MUTE the radio, if on, when the system is sounding an audio tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARK ASSIST SYSTEM OFF” message for as long as the vehicle is in REVERSE. If “CLEAN PARK ASSIST SENSORS” appears in the EVIC after making sure the rear fascia/bumper is free from snow, ice, mud, dirt or other obstruction, see your authorized dealer.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Jackhammers, large trucks, and other vibrations could affect the performance of ParkSense威. properly. The ParkSense威 system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ bumper. • When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST SYSTEM OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 CAUTION! WARNING! • ParkSense威 is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense威 in order to be able to stop in time when an obstacle is detected.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using the ParkSense威 Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 When displayed, static grid lines will illustrate the width that will help indicate the distance to the rear of the of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate center of the vehicle to assist with aligning to a hitch/ distances for each zone: receiver.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 4. Enable or disable the rear camera feature by selecting illuminates the instrument panel cupholders, two swiveling LED lights, flip-down sunglass storage, conversa“enable rear camera in reverse” soft-key. tion mirror, optional power sliding door switches and an 5. Press the “save” soft-key. optional power liftgate switch.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Interior Lighting At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 3 Full Open Position Conversation Mirror Position From this position, the door can be fully closed or, by NOTE: From the “conversation mirror” position, the rotating upward about 3/4 of the way and releasing, door can only be closed. positioned for conversation mirror use. To return to the full open position, the door must first be closed and then opened by pressing the latch again to release.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights — If Equipped” in “Understanding the Features Of Your Vehicle” for further information.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons, located on either the overhead console, headliner or sunvisor, designate the three different HomeLink威 channels. The HomeLink威 indicator is located above the center button. HomeLink威 Buttons/Sunvisor/Headliner NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 position and press and hold the two outside HomeLink威 Before You Begin Programming HomeLink姞 Be sure that your vehicle is parked outside of the garage buttons (I and III) for up 20 seconds or until the red before you begin programming. indicator flashes.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 3. Simultaneously press and hold both the Homelink威 NOTE: You have 30 seconds in which to initiate the next button you want to program and the hand-held transmit- step after the LEARN button has been pressed. ter button. 6. Return to the vehicle and press the programmed 4. Continue to hold both buttons and observe the indi- HomeLink威 button twice (holding the button for two cator light. The Homelink威 indicator will flash slowly seconds each time).
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press and hold the desired HomeLink威 button until 4. Continue to hold both buttons and observe the indithe indicator light begins to flash after 20 seconds. Do not cator light. The Homelink威 indicator will flash slowly and then rapidly after Homelink威 has received the frerelease the button. quency signal from the hand-held transmitter. Release 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 to pick up the signal during programming. Similar to this Reprogramming A Single HomeLink威 Button To reprogram a channel that has been previously trained, Canadian law, some U.S. gate operators are designed to time-out in the same manner. follow these steps: It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage 2. Press and hold the desired HomeLink威 button until door or gate motor.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Watch for the HomeLink威 indicator to change flash Reprogramming A Single HomeLink威 Button rates. When it changes, it is programmed. It may take up To reprogram a channel that has been previously trained, to 30 seconds or longer in rare cases. The garage door follow these steps: may open and close while you are programming. 1. Turn the ignition switch to the ON/RUN position. 5. Press and hold the programmed HomeLink威 button 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 Security Troubleshooting Tips It is advised to erase all channels before you sell or turn If you are having trouble programming HomeLink威, here in your vehicle. are some of the most common solutions: To do this, press and hold the two outside buttons for • Replace the battery in the original hand-held transmitter. 20 seconds until the red indicator flashes. Note that all channels will be erased.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch 241 WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. automatically. This is called “Express Close”. During Express Close operation, any movement of the sunroof switch will stop the sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 NOTE: If three consecutive sunroof close attempts re- Sunshade Operation sult in Pinch Protect reversals, the fourth close attempt The sunshade can be opened manually. However, the will be a Manual Close movement with Pinch Protect sunshade will open automatically as the sunroof opens. disabled. NOTE: The sunshade cannot be closed if the sunroof is Pinch Protect Override open. If a known obstruction (ice, debris, etc.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Sunroof Fully Closed Use only a non-abrasive cleaner and a soft cloth to clean Press the switch forward and release to ensure that the the glass panel. sunroof is fully closed. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 CAUTION! Instrument Panel Outlets NOTE: To ensure proper operation a MOPAR威 cigar knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console (if equipped) shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet. On vehicles equipped with the Super Console the power outlets are located under the retractable cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both controlled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets. 3 The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 110 Volt, 150 Watt inverter outlet (if equipped) converts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat. 249 The power inverter switch is located on the instrument panel below the climate controls. To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. CUPHOLDERS There are cupholders located throughout the interior. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal. Refer to “Cleaning The Instrument Panel Cupholders” in “Maintaining Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 For rear passengers two cupholders are located in the Super Console — If Equipped On models equipped with the Super Console, there are pull-out drawer, located in the back of the Super Console. two cupholders located in the center of the console. Pull the drawer out to the first position to use the cupholders.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Premium Console Cupholders — If Equipped On models equipped with premium center consoles, there are four cupholders located on the top of the console. Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommodates up to a 20 oz (.6 L) plastic bottle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Upper Glove Compartment To open the upper compartment, press in on the button, Glove Compartments located on the left side of the upper door. The door will Upper and lower glove compartments are located on the automatically open. passenger side of the instrument panel. STORAGE Upper and Lower Glove Compartments Upper Compartment To close the compartment door, push downward on the door’s surface to latch the door closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 NOTE: The lower compartment is equipped with a lock Lower Glove Compartment To open the lower compartment pull out on the release that is part of the compartment handle. handle. Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Seatback Storage — If Equipped Umbrella Holder The driver’s seatback has a primary storage pocket on all An umbrella holder has been conveniently molded into models and an optional secondary mesh pocket. the left front door entry scuff molding.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 Second Row Seat Storage Bins — If Equipped The seat storage bins are located on the floor in front of the second row seats. The area below the covers can be used for storage when the second row seat is in the upright position. 3 Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙Lock⬙ position to allow greater access to the storage bin.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) In a collision, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin covers open. • Keep the storage bin covers closed and latched while the vehicle is in motion. • DO NOT use a storage bin latch as a tie down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 CAUTION! The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. 3 Seat Storage Bin Cover Emergency Release Lever As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 CONSOLE FEATURES • Four cupholders accept up to extra large size beverage There are three consoles available: Basic, Premium and cups or 20 oz (.6 L) plastic bottles. Cupholders are Super. dishwasher safe for cleaning. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 • Large console center storage will store headphones for Position 1 shows the console closed with four cupholders the available rear DVD entertainment system or other and a convenient storage tray. items • 12 Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. 3 • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 shows the raised storage tray revealing a large easy access to the storage area below and provides two of the four cupholders for the second row passengers. storage area below. Console Position 2 Console Position 3 Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 3. Pull rearward to disengage from floor and remove console. To reinstall the console: 1. Position the console at a slight angle (rear slightly higher than the front). 2. Slide the console forward into the floor bracket. 3. Rotate the rear of the console down until it is resting on the floor bracket. Console Position 4 To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the console. 2.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. Super Console — If Equipped The Super Console contains multiple storage areas, front lower pass through, top forward bin, top rearward bin and rear pull out drawer. The super console contains a pass through storage area accessible for both the driver and front passenger.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 NOTE: The front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for the rear passengers.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Rechargeable Flashlight The rechargeable flashlight is mounted on the right side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by a lithium battery that recharges when snapped back into place and the vehicle is either running or the key is in the accessory position. Press in on the flashlight to release it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 ROOF LUGGAGE RACK — IF EQUIPPED The crossbars on your vehicle are delivered stowed within the roof rack side rails. If adding cargo, deploy the crossbars. Distribute cargo weight evenly on the roof rack crossbars, to maximum of 150 lbs (68 kg). The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Crossbars are error-proofed and cannot be deployed or stowed in the incorrect positions. • To help control wind noise, stow the crossbars in the side rails when they are not in use. Deploying the Crossbars To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar from its stowed position in the side rail. Repeat with crossbar on the opposite side.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down. 3 Deployed Position Then, position the crossbars across the roof.
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The crossbars are identical and can be placed in any two of the three deploy positions. Crossbar To Side Rail Installation Deploy Positions – Choose Two Of Three Make sure the directional arrows on the crossbars align with the directional arrows on the side rails. Set the crossbars into the deployed positions. Once the crossbars are set into position, tighten the thumb screws completely.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 NOTE: Load should always be secured to crossbars first, with rail tie down loops used as additional securing points if needed. Tie loops are intended as supplementary tie down points only. Do not use ratcheting mechanisms with the tie loops. 3 Tightening Crossbar Stowing the Crossbars Reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Check deployed crossbars frequently and retighten thumb screws as necessary. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without the crossbars deployed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack. SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the screen is completely to the top of the window, To lower the sun screen, gently lift the tab upward to extend the top bar of the sun screen over the two hooks disengage the hooks, and feed the screen back into the attached to the top of the window. base sill.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 283 ▫ EVIC Red Telltale Lights . . . . . . . . . . . . . . . 306 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 284 ▫ Oil Change Required . . . . . . . . . . . . . . . . . . 309 䡵 Instrument Cluster — Premium . . . . . . . . . . . 285 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . 310 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 286 ▫ Vehicle Speed . . . . . . . . .
280 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Messages # . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 328 ▫ Compass / Temperature Display . . . . . . . . . 313 ▫ Operation Instructions - Auxiliary Mode . . . . 330 ▫ Customer-Programmable Features (System Setup) . . . . . . . . . . . . . . . . . . . . . . 315 䡵 Media Center 130 With Satellite Radio (Sales Code RES+RSC). . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 iPod威/USB/MP3 Control — If Equipped . . . . . 346 ▫ Connecting The iPod威 Or External USB Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 348 ▫ Controlling The iPod威 Or External USB Device Using Radio Buttons . . . . . . . . . . . . . 348 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 349 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . .
282 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Replacing The Remote Control Batteries . . . . 372 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 393 ▫ Headphones Operation . . . . . . . . . . . . . . . . 372 ▫ Manual Heating And Air Conditioning System — If Equipped . . . . . . . . . . . . . . . . . 393 ▫ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 ▫ Replacing The Headphone Batteries . . . . . . . 374 ▫ Unwired威 Stereo Headphone Lifetime Limited Warranty . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 283 INSTRUMENT PANEL FEATURES 4 1 2 3 4 — Air Vents — Instrument Cluster — Shift Lever — Radio 5 6 7 8 — — — — Upper Glove Compartment Lower Glove Compartment Climate Controls DVD – If Equipped 9 — Storage Bin 10 — Cup Holders 11 — Switch Bank 12 — Ignition Switch 13 — Hood Release 14 — Dimmer Switch 15 — Headlight Switch
284 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 285 INSTRUMENT CLUSTER — PREMIUM 4
286 UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to 1. Tachometer alert you to turn the signal off. If either indicator flashes The red segments indicate the maximum permissible at a rapid rate, check for a defective outside light bulb. engine revolutions per minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the 5.
UNDERSTANDING YOUR INSTRUMENT PANEL odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service.
288 UNDERSTANDING YOUR INSTRUMENT PANEL CHAngE OIL Your vehicle is equipped with an engine oil change indicator system. The CHAngE OIL message will flash in the instrument cluster odometer for approximately 12 seconds, after a single chime has sounded, to indicate gASCAP the next scheduled oil change interval.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 2. Fully depress the accelerator pedal, slowly, three times If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system within 10 seconds. is not functioning and that service is required. However, 3. Turn the ignition switch to the OFF/LOCK position. the conventional brake system will continue to operate NOTE: If the indicator message illuminates when you normally if the BRAKE warning light is not on.
290 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should maintain correct tire pressure, even if under-inflation has determine the proper tire inflation pressure for those not reached the level to trigger illumination of the TPMS low tire pressure telltale. tires.) Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 tires or wheels on your vehicle, to ensure that the 9. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of replacement or alternate tires and wheels allow the TPMS an onboard diagnostic system, called OBD, that to continue to function properly. monitors engine and automatic transmission conCAUTION! trol systems. The light will illuminate when the key is in the ON/RUN position, before engine start.
292 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 • Each time the ignition is turned to ON/RUN, the ESC 13. Fuel Door Reminder The arrow in this symbol is a reminder that the system will be ON, even if it was turned off previously. Fuel Filler Door is located on the left side of the • The ESC system will make buzzing or clicking sounds vehicle. when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver 14. Fuel Gauge that caused the ESC activation.
294 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Brake Warning Light 16. Shift Lever Indicator This light monitors various brake functions, The Shift Lever Indicator is self-contained within the including brake fluid level and parking brake instrument cluster. It displays the gear position of the application. If the brake light turns on it may automatic transmission.
UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
296 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is 20. Temperature Gauge applied with the ignition switch in the ON/RUN posi- The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that tion. the engine cooling system is operating satisfactorily. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph. 297 while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
298 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Engine Temperature Warning Light This light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches H , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H , the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. 25.
UNDERSTANDING YOUR INSTRUMENT PANEL 26. Transmission Temperature Warning Light During sustained high speed driving or trailer towing up long grades on hot days, the automatic transmission oil may become too hot. When the transmission overheat warning light turns on, you will experience reduced vehicle performance until the automatic transmission cools down. Once the transmission has cooled down and the light turns off, you may continue to drive normally.
300 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 The system allows the driver to select information by UP Button pressing the following buttons mounted on the steering Press and release the UP button to scroll upwheel: ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub-menus. DOWN Button Press and release the DOWN button to scroll downward through the main menus and submenus.
302 UNDERSTANDING YOUR INSTRUMENT PANEL The main display area will normally display the main BACK Button Press the BACK button to scroll back to a menu or the screens of a selected feature of the main menu. The main display area also displays ⬙pop up⬙ previous menu or sub-menu. messages that consist of approximately 60 possible warning or information messages.
UNDERSTANDING YOUR INSTRUMENT PANEL • Unstored Messages This message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are ⬙Turn Signal On⬙ (if a turn signal is left on) and ⬙Lights On⬙ (if driver leaves the vehicle). • Unstored Messages Until RUN These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state.
304 UNDERSTANDING YOUR INSTRUMENT PANEL • Damaged Key • LOW WASHER FLUID • Key not programmed • Oil Change Required • Vehicle Not in Park • Left Front Turn Signal Light Out • Press Brake Pedal and Push Button to Start • Left Rear Turn Signal Light Out • Door(s) Ajar (with a single chime, if vehicle is in • motion) • • Liftgate Ajar (chime will sound when vehicle starts • moving) • • Low Tire Pressure • • Service TPM System (refer to “Tire Pressure Monitoring System” in “Starting And Operating”) •
UNDERSTANDING YOUR INSTRUMENT PANEL • Blind Spot System Not Available — This message is displayed to indicate the Blind Spot Monitor (BSM) system is temporarily unavailable due to sensor blockage, electronic interference, or other ⬙temporary⬙ conditions. When this message is displayed both outside rear view icons will be illuminated. If electronic interference is present, the BSM system will illuminate the icon only on the side of interference as long as interference is present.
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Speed Control SET This light will turn on when the electronic speed control is SET. For further information, refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle.” EVIC Amber Telltale Lights This area will show reconfigurable amber caution telltales. These telltales include: to turn off the message. If the problem continues, the message will appear the next time the vehicle is started.
UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. 307 vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an authorized dealer.
308 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Engine Temperature Warning Light This light warns of an overheated engine condition.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. Oil Change Required Your vehicle is equipped with an engine oil change indicator system.
310 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy Press and release the UP or DOWN button until “Fuel Economy” displays highlighted in the EVIC and press the SELECT button. The following Fuel Economy functions display in the EVIC: • Average Fuel Economy (AVG) • Distance To Empty (DTE) • Miles Per Gallon (MPG) Average Fuel Economy This display shows the average fuel economy since the last reset. The Average Fuel Economy can be reset by following the prompt in the EVIC to use the SELECT button.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 NOTE: Significant changes in driving style or vehicle current speed in mph or km/h. Pressing the SELECT loading will greatly affect the actual drivable distance of button a second time will toggle the unit of measure between mph or km/h. the vehicle, regardless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL” message.
312 UNDERSTANDING YOUR INSTRUMENT PANEL Trip B Shows the total distance traveled for Trip B since the last reset. Units Press and release the UP or DOWN button until “Units” displays highlighted in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if Elapsed Time equipped) can be changed between English and Metric Shows the total elapsed time of travel since the last reset units of measure.
UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Temperature Displays the actual oil temperature. • Oil Pressure Displays the actual oil pressure. 313 Compass / Temperature Display The compass readings indicate the direction the vehicle is facing. The EVIC will display one of eight compass readings and the outside temperature.
314 UNDERSTANDING YOUR INSTRUMENT PANEL metallic objects) until the CAL indicator displayed in the 4. Press and release the SELECT button to start the EVIC turns off. The compass will now function normally. calibration. The “CAL” indicator will be displayed in the EVIC. NOTE: A good calibration requires a level surface and an environment free from large metallic objects such as 5.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 315 2. Press the UP or DOWN button until the Setup (Customer-Programmable Features) menu is reached, then press the SELECT button. 3.
316 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the UP or DOWN button until ⬙System Setup⬙ is highlighted in the main menu of the EVIC. Then press the SELECT button to enter the System Setup sub-menu. Press and release the UP or DOWN button to select a feature form the following choices: Language When in this display you may select one of five languages for all display nomenclature, including the trip functions and the navigation system (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock Doors When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
318 UNDERSTANDING YOUR INSTRUMENT PANEL In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the key is turned to RUN. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL Headlamps with Wipers (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
320 UNDERSTANDING YOUR INSTRUMENT PANEL Illuminated Approach When this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are unlocked with the RKE transmitter. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
322 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/ RHB) CD/DVD/HDD/NAV — IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Refer to your Uconnect™ Multimedia RHR, RER, RBZ or RHB user’s manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 SEEK Buttons Press and release the SEEK buttons to search for the next NOTE: The ignition switch must be in the ON or ACC listenable station in AM/FM mode. Press the right switch position to operate the radio. to seek up and the left switch to seek down. The radio Power Switch/Volume Control (Rotary) will remain tuned to the new station until you make Push the ON/VOLUME control knob to turn on the another selection. Holding either button will bypass radio.
324 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the knob to save time change. mid-range tones. 5. To exit, press any button/knob, or wait five seconds. Push the rotary TUNE/SCROLL control knob a third RW/FF time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Push the rotary TUNE/SCROLL control knob again to You may add a second station to each pushbutton by repeating the above procedure with this exception: Press exit setting tone, balance, and fade. the SET/RND button twice and SET 2 will show in the AM/FM Button display window. Each button can be set for SET 1 and Press the buttons to select either AM or FM mode. SET 2 in both AM and FM.
326 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or the radio will reinsert the CD but will not play it. RW or another CD button is pressed. The RW (Reverse) A disc can be ejected with the radio and ignition OFF. button works in a similar manner.
328 UNDERSTANDING YOUR INSTRUMENT PANEL Notes on Playing MP3 Files • Maximum number of files: 255 The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited. For large numbers writing MP3 files, pay attention to the following restricof files and/or folders, the radio may be unable to tions.
UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
330 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) 331 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or NOTE: The radio sales code is located on the lower right ACC position to operate the radio. side of the radio faceplate. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
332 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text will begin to blink. message broadcast from an FM station (FM mode only). 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
334 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be sePush the rotary TUNE/SCROLL control knob a third lected.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk 16-Digit Character Display Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Program Type Top 40 Weather 335 16-Digit Character Display Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be
336 UNDERSTANDING YOUR INSTRUMENT PANEL hours, press the TUNE/SCROLL control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side TUNE/SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 If you insert a disc with the ignition ON/RUN and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display NOTE: will show the track number, and index time in minutes • The ignition switch must be in the ON/RUN or ACC and seconds. Play will begin at the start of track 1. position to operate the radio.
338 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or the radio will reinsert the CD but will not play it. another CD button is pressed. The RW (Reverse) button A disc can be ejected with the radio and ignition OFF. works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 Notes On Playing MP3 Files • Maximum number of files: 255 The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited. For large numbers writing MP3 files, pay attention to the following restricof files and/or folders, the radio may be unable to tions.
340 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
342 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. TIME Button (Auxiliary Mode) Press this button to change the display to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. 343 using the TUNE/SCROLL control knob until Sirius ID is selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display.
344 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will • The vehicle is parked in an underground parking remain tuned to the new channel until you make another structure or under a physical obstacle. selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons channel with the same selected Music Type name.
346 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 This feature allows an iPod威 or external USB device to be Connecting The iPod姞 Or External USB Device plugged into the USB port, located in the glove compart- Use the connection cable to connect an iPod威 or external USB device to the vehicle’s USB connector port which is ment. located in the glove compartment. iPod威 control supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices. Some iPod威 software versions may not fully support the iPod威 control features.
348 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The glove compartment will have a position where the iPod威 or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. This allows routing of the cable without damaging it while closing the lid. If a cut out is not available in the glove compartment, route the cable away from the lid latch and in a place that will allow the lid to close without damaging the cable.
UNDERSTANDING YOUR INSTRUMENT PANEL control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. 349 • Jump backward in the current track by pressing and holding the << RW button. Holding the << RW button long enough will jump to the beginning of the current track. Play Mode When switched to iPod威/USB/MP3 control mode, the iPod威 or external USB device automatically starts Play • Jump forward in the current track by pressing and holding the FF >> button.
350 UNDERSTANDING YOUR INSTRUMENT PANEL to the next screen of data for that track. Once all screens have been viewed, the last INFO button press will go back to the play mode screen on the radio. device, or press the VR button and say ⬙Shuffle ON⬙ or ⬙Shuffle Off⬙. If the RND icon is showing on the radio display, then the shuffle mode is ON. • Pressing the REPEAT button will change the audio device mode to repeat the current playing track or press the VR button and say ⬙Repeat ON⬙ or ⬙Repeat Off⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable. • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • During all List modes, the iPod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (counterclockwise) to get to the track faster.
352 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 or external USB device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威 or external USB device, or connections to the iPod威 or external USB device in the vehicle, can cause damage to the device and/or to the connectors.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 2. After the ⬙Ready⬙ prompt and the following beep, say UCONNECT™ MULTIMEDIA VIDEO ⬙Setup⬙, then ⬙Select Audio Devices⬙. ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED 3. Say the name of the audio device or ask the Getting Started Uconnect™ phone system to list audio devices. • Screen(s) located in the overhead console : Unfold the overhead LCD screen(s) by pushing the button on the Next Track overhead console behind the screen(s).
354 UNDERSTANDING YOUR INSTRUMENT PANEL • Cycle the ignition to the ON or ACC position. • Turn on the VES™ player (if equipped on Dual Screen System) by pushing the Power button, located on the far left, or by pressing the button on the Remote Control. • When the Video Screen(s) are open and a DVD is inserted into the VES™ player, the screen(s) turn(s) on automatically, the headphone transmitters turn on and playback begins.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: NOTE: Certain high-end video games, such as Playstation3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter. Refer to the Power Inverter section in your vehicle’s Owner’s Manual for more information. 4 Ensure the Remote Control and Headphone switch is on Channel 1. Using The Remote Control 1.
356 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the 1 soft-key and then touch either AUX 1 or AUX 2 in the VES column (depending which AUX input 1. Press the MENU hard-key on the radio faceplate. is used). To exit press the back arrow soft-key at the top 2. Touch the Rear VES soft-key to display the Rear VES of the screen. Controls. If a channel list is displayed, press the HIDE LIST soft-key to display the Rear VES Controls screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 Ensure the Remote Control and Headphone switch is on Channel 2. Using The Remote Control 1. Press the MODE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen. 2.
358 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and 1. Press the MENU hard-key on the radio faceplate. choose an audio source. To exit touch the back arrow 2. Touch the Rear VES soft-key to display the Rear VES soft-key at the top left of the left screen. Controls. If a channel list is displayed, press the HIDE LIST soft-key to display the Rear VES Controls screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 3. To watch a DVD on Screen 1 for second row passengers, ensure the Remote Control and Headphone switch NOTE: Typically there are two different ways to operate is on Channel 1. the features of the Video Entertainment System (VES)™. 4. To watch a DVD on Screen 2 for third row passengers, • The Remote Control ensure the Remote Control and Headphone switch is on Channel 2.
360 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control 1. Press the MODE button on the Remote Control. NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. 2. While looking at Screen 1 or 2, highlight DISC by • Channel/Screen 2 select mode information is shown either pressing Up/Down/Left/Right buttons or by reon the right side of the screen. peatedly pressing the MODE button, then press ENTER. • The VES™ will retain the last setting when turned off.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 4 Rear VES Soft-key Select Channel/Screen 1 And DISC In The MEDIA Column 3. Touch the 1 or 2 soft-key based on the channel you want to change and then the DISC soft-key in the MEDIA NOTE: column. To exit touch the back arrow at the top left of the • To view a DVD on the radio press the RADIO/MEDIA hard-key, on the radio faceplate, then touch the DISC screen. tab soft-key and then the VIEW VIDEO soft-key.
362 UNDERSTANDING YOUR INSTRUMENT PANEL • Viewing a DVD on the Touch-Screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift lever must be in the PARK position for vehicles with automatic transmission. In vehicles with manual transmission the parking brake must be engaged. • Touching the screen on a Touch-Screen radio while a DVD is playing brings up basic remote control functions for DVD play such as scene selection, Play, Pause, FF, RW, and Stop.
UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control 1. Press the MODE button on the Remote Control. 363 NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. 2. While looking at Screen 1 or 2, highlight VES DISC by • Channel/Screen 2 select mode information is shown either pressing Up/Down/Left/Right buttons or by reon the right side of the screen. peatedly pressing the MODE button, then press ENTER • The VES™ will retain the last setting when turned off.
364 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls 1. Press the MENU hard-key on the radio faceplate. 3. Touch the 1 or 2 soft-key and then the DISC soft-key in the VES column. To exit touch the back arrow soft-key at the top left of the screen. 2. Touch the Rear VES soft-key to display the Rear VES Controls. If a channel list is displayed, touch the HIDE LIST soft-key to display the Rear VES Controls screen.
UNDERSTANDING YOUR INSTRUMENT PANEL • Viewing a DVD on the Touch-Screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift lever must be in the PARK position for vehicles with automatic transmission. In vehicles with manual transmission the parking brake must be engaged. 2.
366 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To listen to an audio source on Channel 1 while a video is playing on Channel/Screen 2, touch the 1 1. Press the MENU hard-key on the radio faceplate. soft-key and choose an audio source. To listen to an audio 2. Touch the Rear VES soft-key to display the Rear VES source on Channel 2 while a video is playing on Controls.
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Third Row Swivel Screen (If Equipped) • The third row screen or Screen 2 has the ability to lower and swivel to face forward. • While the swivel screen is facing forward, the second row screen or Screen 1 must be fully open in order for the swivel screen (Screen 2) to work.
368 UNDERSTANDING YOUR INSTRUMENT PANEL Important Notes For Dual Video Screen System Remote Control • VES is able to transmit two channels of stereo audio and video simultaneously. • In split screen mode the left side equates to Channel 1 and the right side equates to Channel 2. • Selecting a video source on Channel 1, the video source will display on the second row screen or Screen 1 and can be heard on Channel 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 369 2. Channel Selector Indicators – When a button is 6. 䉲 / Prev – In radio modes, press to select to the pressed, the currently affected channel or channel button previous station. In disc modes, press to advance to the start of the current or previous audio track or video is illuminated momentarily. chapter. In menu modes, use to navigate in the menu. 3. Light – Turns the remote control backlighting on or off.
370 UNDERSTANDING YOUR INSTRUMENT PANEL disc in a radio with a multiple-disc changer, PROG Up and the disc is stopped, press the SETUP button to access selects the next disc and PROG Down selects the previ- the DVD Setup menu. (see the DVD Setup Menu of this manual.) ous disc. 11. MUTE – Press to mute the headphone audio output 16. BACK – When navigating in menu mode, press to for the selected channel. return to the previous screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 Remote Control Storage The video screen(s) come with a built in storage compartment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be very difficult to remove.
372 UNDERSTANDING YOUR INSTRUMENT PANEL DVD player, follow the radio’s instructions to turn Headphones Operation Video Lock on. The radio and the video screen(s) The headphones receive two separate channels of audio using an infrared transmitter from the video screen. indicate when Video Lock is active.
UNDERSTANDING YOUR INSTRUMENT PANEL 373 Controls The headphone power indicator and controls are located on the right ear cup. NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off. Changing the Audio Mode for Headphones 1. 2. 3. 4. Volume Control Power Button Channel Selection Switch Power Indicator 1.
374 UNDERSTANDING YOUR INSTRUMENT PANEL • When both switches are on Channel 2, the Remote is Replacing The Headphone Batteries controlling Channel 2 and the headphones are tuned Each set of headphones requires two AAA batteries for operation. To replace the batteries: to the audio of the VES™ Channel 2. • Locate the battery compartment on the left ear cup of the headphones, and then slide the battery cover 3. If the video screen is displaying a video source (such downward.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 How Long Does The Coverage Last? This warranty lasts NATURE WHATSOEVER. Some states and jurisdictions may not allow the exclusion or limitation of incidental or as long as you own the Product. consequential damages, so the above limitation may not What Does This Warranty Cover? Except as specified apply to you. This warranty gives you specific legal below, this warranty covers any Product that in normal rights.
376 UNDERSTANDING YOUR INSTRUMENT PANEL You may register your Unwired威 wireless headphones selected radio mode. When shared, the radio has priority online at www.unwiredtechnology.com or by phone at over the VES™ or all radio modes (FM, AM, and SAT). The VES™ has the ability to switch tuner (AM/FM), 1-888-293-3332. SEEK, SCAN, TUNE, and recall presets in radio modes as System Information long as it is not in shared mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Information Mode Display 377 3. Channel 1 Audio Only/Mute 4. Channel 2 Mode 5. Channel 2 Shared Status 6. Channel 2 Audio Only/Mute 7. Channel 1 ENTER Button Action 8. Channel 2 ENTER Button Action 9. Clock 10. Video Lock 11. Not Available / Error Information Mode Video Screen Display 1. Channel 1 Mode 2. Channel 1 Shared Status 12.
378 UNDERSTANDING YOUR INSTRUMENT PANEL Numeric Keypad Menu screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control’s navigation buttons (䉱, 䉲, 䉴, 䉳) to navigate to the desired digit. 2. When the digit is highlighted, press the remote control’s ENTER button to select the digit. Repeat these steps until all digits are entered. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 379 press the remote control’s ENTER button to tune to that commands which control playback of the disc. Using the station. To jump through the list more quickly, navigate options you can activate or cancel Scan play and Random play. to the Page Up and Page Down icons on the screen.
380 UNDERSTANDING YOUR INSTRUMENT PANEL control’s SETUP button activates the Display Settings menu. These settings control the appearance of the video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change these settings under normal circumstances. Listening To Audio With The Screen Closed To listen to only audio portion of the channel with the screen closed: • Set the audio to the desired source and channel. • Close the video screen.
UNDERSTANDING YOUR INSTRUMENT PANEL If the screen is closed and there is no audio heard, verify that the headphones are turned on (the ON indicator is illuminated) and the headphone selector switch is on the desired channel. If the headphones are turned on, press the remote control’s power button to turn audio on. If audio is still not heard, check that fully charged batteries are installed in the headphones.
382 UNDERSTANDING YOUR INSTRUMENT PANEL Recorded Discs • For multi-session CDs that contain only multiple CDAudio sessions, the player will renumber the tracks so each track number is unique. The VES™ DVD player will play CD-R and CD-RW discs recorded in CD-Audio or Video-CD format, or as a CD-ROM containing MP3 or WMA files. The player will • For CD Data (or CD-ROM) discs, always use the ISO-9660 (Level 1 or Level 2), Joliet, or Romeo format.
UNDERSTANDING YOUR INSTRUMENT PANEL 383 The recommended method for labeling recordable discs • Any file that is copy protected (such as those down(CD-R, CD-RW, and DVD-R) is with a permanent marker. loaded from many online music stores) will not play. Do not use adhesive labels as they may separate from the The DVD player will automatically skip the file and disc, become stuck, and cause permanent damage to the begin playing the next available file. DVD player.
384 UNDERSTANDING YOUR INSTRUMENT PANEL • To change the current directory, use the remote con- skipping forward 1.0 to 3.0 seconds at a time. If the end trol’s PROG Up and Down buttons. of the disc is reached, the DVD player will return to the beginning of the disc and attempt to play the start of the Disc Errors first track.
UNDERSTANDING YOUR INSTRUMENT PANEL Display Other Language Setup 385 All of the Language settings have a special ⬙Other⬙ setting to accommodate languages other than Japanese or English. These languages are selected using a special fourdigit code. To enter a new language code, activate the DVD Setup Menu.
386 UNDERSTANDING YOUR INSTRUMENT PANEL • Using the remote control Up and Down cursor buttons, select a digit for the current position. After selecting the digit, press the remote control’s Right cursor button to select the next digit. Repeat this digit selection sequence for all four digits. Rating and Password Setup The Rating and Password settings work together to control the types of DVDs that your family watches.
UNDERSTANDING YOUR INSTRUMENT PANEL 387 The default rating is Level 8 (play all discs without a To set the password, activate the DVD Setup Menu and password) and the default password is 0000. follow these additional instructions: • Using the remote control Left and Right cursor buttons, select the Rating tab. • Highlight ⬙Change Password⬙, and then press the remote control’s ENTER button. • Enter the current password.
388 UNDERSTANDING YOUR INSTRUMENT PANEL • Using the remote control’s Up and Down cursor buttons to set the value for the current digit and the remote control’s Right cursor button to select digits, enter the new password. • After the four-digit password is entered, press the remote control’s ENTER button to accept the change.
UNDERSTANDING YOUR INSTRUMENT PANEL 389 To set the rating, activate the DVD Setup Menu and • Using the remote control’s Up and Down cursor follow these additional instructions: buttons, select the new rating level, and then press the remote control’s ENTER button to accept the change. • Using the remote control’s Left and Right cursor buttons, select the Rating tab.
390 UNDERSTANDING YOUR INSTRUMENT PANEL General Information This system complies with Part 15 of the FCC Operation is subject to the following two conditions: STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of the radio from AM to FM, or to CD mode, depending on which radio is in the vehicle.
392 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particuCD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Climate Control system allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Manual Heating And Air Conditioning System — If Equipped The controls for the manual system in this vehicle contain a series of outer rotary dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions.
394 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Left Front Temperature Control Provides left front seat occupant with independent temperature control. Turn left for cooler or right for warmer temperature settings. operation if the blower control is left in the “O” (Off) position. Blower control should be left in the ⬙ON⬙ position to allow the climate control to either warm or cool the vehicle. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 395 NOTE: 7. Front Defrost Mode Air is directed through the windshield and side • You can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second window demist outlets. Use Defrost mode with time. maximum blower and temperature settings for best windshield and side window defrosting. • To prevent excessive battery drain, use the rear window defroster only when the engine is operating.
396 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. NOTE: • If the Recirculation button is pressed when the system is in Defrost mode the Recirculation LED indicator will flash 3 times to indicate Recirculation mode is not allowed. • In Floor and Mix mode the system will turn off Recirculation mode after five minutes of operation. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL 397 • In order to prevent fogging, when the Recirculation 11. Floor Mode Button Air is directed through the floor outlets with a button is pressed and the mode control is set to Panel, small amount through the defrost and side window the A/C will engage automatically. demist outlets. • The A/C can be deselected manually without disturbing the mode control selection. 12. Bi-Level Mode Button Air is directed through the panel and floor outlets. 10.
398 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For maximum airflow to the rear, the center The rear blower and temperature controls for the rear instrument panel outlets can be directed toward the rear seat passengers are located in the headliner, near the center of the vehicle. seat passengers. Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Rotate the temperature control knob to the desired temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control The primary control for the rear blower is on the front climate control unit, located on the instrument panel. Only when the front control for the rear blower is in the REAR position do the second row seat occupants have control of the rear blower speed. The rear blower control, located in the rear overhead console, has an off position and a range of blower speeds.
400 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the Floor Mode Air comes from the floor outlets. lock symbol on the temperature knob is illuminated, and the rear overhead adjustments are inoperable. Rear Mode Control Automatic Temperature Control (ATC) — If Equipped Headliner Mode Air comes from the outlets in the headliner.
UNDERSTANDING YOUR INSTRUMENT PANEL The Three-Zone ATC system automatically maintains the interior comfort level desired by the driver and all passengers. The system automatically adjusts the air temperature, the airflow volume, amount of outside air recirculation and the airflow direction. This maintains a comfortable temperature, even under changing conditions. 401 1.
402 UNDERSTANDING YOUR INSTRUMENT PANEL 11. Rear Lock 7. Right Front Seat Occupant Temperature Display This display shows the temperature setting for the right Press and release the Rear Lock button on the front ATC panel to lock and unlock the rear climate controls front seat occupant. 8. Front Defrost Button Press and release to change the current setting, the indicator illuminates when ON. Performing this function will cause the ATC to switch into manual mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 403 To change the rear system settings: 15. Mode Control Button Press and release to select between Modes (Panel, Bi1. Press ⬙REAR⬙ button to change control to rear control Level, Floor, Mix). Performing this function will cause the mode, Rear display (below) will appear. Control funcATC to switch into manual mode. tions now operate rear system. 16. Recirculation Control Button 2.
404 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Next, adjust the temperature you would like the system to maintain, by adjusting the driver, front passenger, and rear seat rotary temperature knobs. Once the 2. Rear Temperature Display desired temperature is displayed, the system will achieve This display shows the temperature setting for the rear and automatically maintain that comfort level. seat occupants. 3. When the system is set up for your comfort level, it is 3.
UNDERSTANDING YOUR INSTRUMENT PANEL customer-programmable feature. Refer to the “Electronic Vehicle Information Center (EVIC) — CustomerProgrammable Features” in this Section. To provide you with maximum comfort in the automatic mode, during cold start-ups, the blower fan will remain on low until the engine warms up. The fan will engage immediately if the Defrost mode is selected, or by changing the front blower knob setting Manual Operation This system offers a full complement of manual override features.
406 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Floor Mode Air is directed through the outlets in the instrument Air comes from the floor outlets. A slight amount of panel. These outlets can be adjusted for direction, air is directed through the defrost and side window and turned on or off to control airflow. demister outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning (A/C) The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system. When in A/C mode and the ATC is set to a cool temperature, dehumidified air flows through the air outlets. If Economy mode is desired, press the A/C button to turn off the A/C mode in the ATC display and deactivate the A/C system.
408 UNDERSTANDING YOUR INSTRUMENT PANEL The rear ATC system is located in the headliner, near the Rear Automatic Temperature Control (ATC) — If center of the vehicle. Equipped The rear ATC system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 409 1. Press the Rear Temperature Lock button on the front NOTE: ATC panel. This turns off the Rear Temperature Lock icon • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts in the rear temperature knob. the temperature, mode and fan speed to provide 2. Rotate the Rear Blower, Rear Temperature and the comfort as quickly as possible. Rear Mode Control knobs to suit your comfort needs.
410 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control The rear blower control knob can be manually set to off, or any fixed blower speed, by rotating the knob from low to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle. CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille, located in the right side trim panel behind the third row seats.
UNDERSTANDING YOUR INSTRUMENT PANEL 411 Headliner Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow. Summer Operation The engine cooling system in air conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating.
412 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Before you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes, in fresh air with the blower setting on high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging Vehicle windows tend to fog on the inside in mild, rainy and/or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips 413 A/C Air Filter On vehicles equipped with Automatic Temperature Control (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in “Maintaining Your Vehicle” for filter replacement instructions.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 419 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 422 ▫ Automatic Transmission . . . . . . . . . . . . . . . 419 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 424 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 419 ▫ Brake/Transmission Shift Interlock System . . 424 ▫ Extreme Cold Weather (Below –20°F Or –29°C) . . . . . . . . . . . . . . . .
416 STARTING AND OPERATING 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 435 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . 452 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . 435 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . 452 ▫ Shallow Standing Water . . . . . . . . . . . . . . . 436 ▫ Tire Identification Number (TIN) . . . . . . . . . 455 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . 437 ▫ Tire Terminology And Definitions . . .
STARTING AND OPERATING 417 ▫ Full Size Spare – If Equipped . . . . . . . . . . . . 466 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 482 ▫ Limited-Use Spare – If Equipped . . . . . . . . . 466 ▫ 3.6L Engine . . . . . . . . . . . . . . . . . . . . . . . . 482 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 467 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 482 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 468 ▫ Gasoline/Oxygenate Blends . . . . . . .
418 STARTING AND OPERATING ▫ Selection Of Engine Oil For Flexible Fuel 䡵 Vehicle Loading . . . . . . . . . . Vehicles (E-85) And Gasoline Vehicles . . . . . . 489 ▫ Vehicle Certification Label . . ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 䡵 Trailer Towing . . . . . . . . . . . . ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . 489 ▫ Common Towing Definitions ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . 490 ▫ Towing Tips . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
420 STARTING AND OPERATING 3. If the engine fails to start, the starter will disengage If The Engine Fails To Start automatically in 10 seconds. If this occurs, turn the WARNING! ignition switch to the OFF position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure (Steps 1–3 • Never pour fuel or other flammable liquids into above). the throttle body air inlet opening in an attempt to NOTE: This vehicle is equipped with a transmission start the vehicle.
STARTING AND OPERATING WARNING! (Continued) • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “Jump Starting” in “What To Do In Emergencies” for further information. 421 CAUTION! To prevent damage to the starter, DO NOT crank the engine for more than 15–second intervals at one time. Wait 10 to 15 seconds before trying again.
422 STARTING AND OPERATING After Starting The idle speed will automatically decrease as the engine warms up. WARNING! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a AUTOMATIC TRANSMISSION standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord.
STARTING AND OPERATING 423 CAUTION! (Continued) WARNING! • Do not move the shift lever between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before moving the shift lever into any gear, make sure your foot is firmly pressing the brake pedal. • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.
424 STARTING AND OPERATING WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the key fob. Once the key fob is removed, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
STARTING AND OPERATING Fuel Economy (ECON) Mode The Fuel Economy (ECON) mode can improve the vehicle’s overall fuel economy during normal driving conditions. Press the “econ” switch in the center stack of the instrument panel and a green light will indicate the ECON mode is engaged. 425 When the Fuel Economy (ECON) Mode is engaged, the vehicle control systems will change the following: • The transmission will upshift sooner and downshift later.
426 STARTING AND OPERATING Six-Speed Automatic Transmission The shift lever position display (located in the instrument panel cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of the PARK position (Refer to Brake/Transmission Shift Interlock System in this section). To drive, move the shift lever from PARK or NEUTRAL to the DRIVE position. The electronically-controlled transmission provides a precise shift schedule.
STARTING AND OPERATING The transmission shift lever has only PARK, REVERSE, NEUTRAL, and DRIVE shift positions. Manual shifts can be made using the Electronic Range Select (ERS) shift control (described later in this section). Moving the shift lever to the left or right (–/ +) while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
428 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever rearward (with the brake pedal released) after you have placed it in PARK. Make sure the transmission is in PARK before leaving the vehicle. • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed.
STARTING AND OPERATING 429 WARNING! (Continued) CAUTION! (Continued) • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the key fob in or near the vehicle. A child could operate power windows, other controls, or move the vehicle.
430 STARTING AND OPERATING REVERSE This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL Use this range when the vehicle is standing for prolonged periods with engine running. The engine may be started in this range. Set the parking brake and shift the transmission into PARK if you must leave the vehicle. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.
STARTING AND OPERATING When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the Electronic Range Select (ERS) shift control (described below) to select a lower gear range. Under these conditions, using a lower gear range will improve performance and extend transmission life by reducing excessive shifting and heat buildup. 431 limited to third gear only.
432 STARTING AND OPERATING 2. Shift the transmission into PARK. Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows the 3. Turn the engine OFF. driver to limit the highest available gear when the shift lever is in the DRIVE position. For example, if you shift 4. Wait approximately 10 seconds. the transmission into 3 (third gear), the transmission will 5. Restart the engine. never shift above third gear, but will shift down into 6.
STARTING AND OPERATING 433 To exit ERS mode, simply press and hold the shift lever to Overdrive Operation the right (+) until “D” is once again displayed in the shift The automatic transmission includes an electronically controlled Overdrive (sixth gear). The transmission will lever position indicator in the instrument cluster.
434 STARTING AND OPERATING Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly different feeling or response during normal operation in the upper gears. When the vehicle speed drops or during some accelerations, the clutch automatically disengages.
STARTING AND OPERATING Traction When driving on wet or slushy roads, it is possible for a layer of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
436 STARTING AND OPERATING Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
438 STARTING AND OPERATING system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticidoes not in any way damage the steering system. pated. Coordinate inspection efforts through an authoWARNING! rized dealer. Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
STARTING AND OPERATING 439 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the PARK position. The foot operated parking brake is positioned below the lower left corner of the instrument panel.
440 STARTING AND OPERATING NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING WARNING! (Continued) • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury.
442 STARTING AND OPERATING • A slight drop or fall away of the brake pedal at the end of the stop WARNING! • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed, or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING Anti-Lock Brake Warning Light The “Anti-Lock Brake Warning Light” monitors the anti-lock brake system. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the “Anti-Lock Brake Warning Light” remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.
444 STARTING AND OPERATING wheel(s) and engine power is reduced, to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential, and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning.
STARTING AND OPERATING brakes. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance. To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence. Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated.
446 STARTING AND OPERATING ESC uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position.
STARTING AND OPERATING ESC On This mode is the normal operating mode for ESC on two-wheel drive vehicles. Whenever the vehicle is started, the ESC system will be in this mode. This mode should be used for most driving situations. ESC should only be turned off for specific reasons as noted below. 447 again, momentarily press the “ESC Off” switch. This will restore the normal “ESC On” mode of operation.
448 STARTING AND OPERATING ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON position. It should turn off with the engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
STARTING AND OPERATING Hill Start Assist (HSA) The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill.
450 STARTING AND OPERATING Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. 7. Press the “ESC Off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “ESC Activation/Malfunction Indicator Light” should turn on and turn off two times. For vehicles not equipped with the EVIC, perform the 8.
STARTING AND OPERATING 451 WARNING! WARNING! (Continued) • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
452 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 453 compact spare tires have the letter “T” or “S” molded • High flotation tire sizing is based on U.S. design into the sidewall preceding the size designation. Exstandards and it begins with the tire diameter molded ample: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
454 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. 455 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
456 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING Tire Loading And Tire Pressure 457 Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
458 STARTING AND OPERATING This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section.
STARTING AND OPERATING 459 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcusengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity. For example, if “XXX” and number and size of occupants.
460 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure.
462 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar or rear edge of the driver’s side door.
STARTING AND OPERATING Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
464 STARTING AND OPERATING WARNING! High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision.
STARTING AND OPERATING 465 with one of the following types of non-matching tempo- Compact spare tire descriptions begin with the letter “T” rary use spares; compact, full size, or limited-use. Do not or “S” preceding the size designation. Example: T145/ install more than one non-matching temporary use spare 80D18 103M. tire/wheel on the vehicle at any given time.
466 STARTING AND OPERATING WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
STARTING AND OPERATING WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressure listed on your Tire and Loading Information Placard located on the driver’s side door opening. Replace (or repair) the original equipment tire at the first opportunity and reinstall it on your vehicle.
468 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original-equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
STARTING AND OPERATING 469 Keep dismounted tires in a cool, dry place with as little It is recommended to replace the two front tires or two exposure to light as possible. Protect tires from contact rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling. If you ever replace a with oil, grease and gasoline. wheel, make sure that the wheel’s specifications match Replacement Tires those of the original wheels.
470 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING CAUTION! 471 CAUTION! (Continued) To avoid damage to your vehicle or tires, observe the following precautions: • Use chains on P225/65R16 and P235/60R16 tires only. P225/65R17 tires do not provide adequate clearance. • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage.
472 STARTING AND OPERATING poorer than that of non-studded tires. Some states proSNOW TIRES Some areas of the country require the use of snow tires hibit studded tires; therefore, local laws should be during the winter. All season tires can be identified by the checked before using these tire types. M+S designation on the tire sidewall.
STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire Rotation 473 TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure based on the cold inflation tire placard pressure requirements found on the tire placard label located on the driver’s-side B-pillar. The tire pressure will vary with temperature by about 1 psi (6.
474 STARTING AND OPERATING The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natural air pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold tire placard pressure.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket sealants or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.
476 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Tire Pressure and the TPMS will monitor the actual tire pressure in Warnings The “Tire Pressure Monitoring Telltale Light” the tire.
STARTING AND OPERATING The “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. The “Tire Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists. A system fault can occur with any of the following scenarios: 477 Vehicles With Compact Spare 1.
478 STARTING AND OPERATING 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the TPMS will automatically update, and the “Tire Pressure Monitoring Telltale Light” will turn off as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) for the TPMS to receive this information.
STARTING AND OPERATING Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure value. The system will automatically update, the graphic display of the pressure value(s) will stop flashing, and the “Tire Pressure Monitoring Telltale Light” will extinguish once the updated tire pressure(s) have been received.
480 STARTING AND OPERATING 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPMS sensors. The EVIC will also display a “SERVICE TPM SYSTEM” message for a minimum of five seconds when a system fault possibly related to an incorrect sensor location fault is present. In this case, the “SERVICE TPM SYSTEM” message is then followed by a graphic display with pressure values still shown.
STARTING AND OPERATING 4. For each subsequent ignition switch cycle, a chime will sound, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a “SERVICE TPM SYSTEM” message for a minimum of five seconds and then display dashes (- -) in place of the pressure value. 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically.
482 STARTING AND OPERATING FUEL REQUIREMENTS 3.6L Engine Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING 483 Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as Ethanol. Fuels blended with oxygenates may be used in your vehicle. E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol content may void the vehicle’s warranty.
484 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with therefore, you should ask your gasoline retailer whether the gasoline contains MMT. It is even more important to E-85 perform the following: look for gasoline without MMT in Canada, because MMT • change the engine oil and oil filter can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and Califor• disconnect and reconnect the battery nia reformulated gasoline.
STARTING AND OPERATING Fuel System Cautions 485 CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
486 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING the other sections of this manual for information on features that are common between Flexible Fuel and gasoline-only powered vehicles. 487 CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85.
488 STARTING AND OPERATING Ethanol Fuel (E-85) When you do switch fuel types it is recommended that: E-85 is a mixture of approximately 85% fuel ethanol and • you do not switch when the fuel gauge indicates less 15% unleaded gasoline. than 1/4 full WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E-85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR威 Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils.
490 STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
492 STARTING AND OPERATING • If the gas cap is not tightened properly, the MIL may VEHICLE LOADING come on. Be sure the gas cap is tightened every time As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label the vehicle is refueled. affixed to the driver’s side door or B-Pillar.
STARTING AND OPERATING • Vehicle Identification Number (VIN) • Type of Vehicle • Month, Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.
494 STARTING AND OPERATING Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added. Figure out the weight on the front and rear of the vehicle separately.
STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
496 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. NOTE: The GCWR rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING 497 Frontal Area Weight-Distributing Hitch The frontal area is the maximum height multiplied by the A weight-distributing system works by applying levermaximum width of the front of a trailer. age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the Trailer Sway Control tow vehicle’s front axle and the trailer’s axle(s).
498 STARTING AND OPERATING WARNING! • An improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • Weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with an authorized hitch and trailer manufacturer or a reputable authorized Recreational Vehicle dealer for additional information.
STARTING AND OPERATING 499 5 With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
500 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow, and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. TRAILER HITCH CLASSIFICATIONS Max. GTW Class (Gross Trailer Wt.
STARTING AND OPERATING 501 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Max. GTW Max. Tongue Wt. (Gross Trailer Wt.) Up to 2 persons & 8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) Luggage 3,600 lbs 360 lbs (163 kg) (1 633 kg)* 3 to 5 persons & 3.6L/Automatic 8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) Luggage 3,350 lbs 335 lbs (152 kg) (1 519 kg)* 6 to 7 persons & 8,750 lbs (3 969 kg) 40 sq ft (3.
502 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side-to-side, which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for the maximum combined weight of occupants and cargo for your vehicle.
504 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
STARTING AND OPERATING Towing Requirements – Tires • Do not attempt to tow a trailer while using a compact spare tire. 505 replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. Towing Requirements – Trailer Brakes • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
506 STARTING AND OPERATING CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING 507 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations.
508 STARTING AND OPERATING Towing Tips Electronic Speed Control – If Equipped Before setting out on a trip, practice turning, stopping • Do not use in hilly terrain or with heavy loads. and backing the trailer in an area away from heavy • When using the speed control, if you experience speed traffic. drops greater than 10 mph (16 km/h), disengage until Automatic Transmission you can get back to cruising speed. The DRIVE gear can be selected when towing.
STARTING AND OPERATING • Air Conditioning Turn off temporarily. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Recreational towing is not allowed. CAUTION! DO NOT flat tow this vehicle. Damage to the drivetrain will result. 509 NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 513 ▫ Preparations For Jacking . . . . . . . . . . . . . . . 522 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 513 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 523 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 514 ▫ Securing The Spare Tire . . . . . . . . . . . . . . . . 528 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 515 ▫ Road Tire Installation . .
512 WHAT TO DO IN EMERGENCIES 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 536 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 539 䡵 Shift Lever Override . . . . . . . . . . . . . . . . . . . 537 ▫ Without The Ignition Key . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS The Hazard Warning flasher switch is located in the lower center area of the instrument panel. 513 IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — slow down.
514 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
WHAT TO DO IN EMERGENCIES 515 WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover.
516 WHAT TO DO IN EMERGENCIES Spare Tire Removal The spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console or under front super console forward bin liner.
WHAT TO DO IN EMERGENCIES 517 6 Super Console 1 — Lower Drawer 2 — Front Drawer 3 — Front Drawer Liner 1. Pull the lower drawer out from the rear of the floor console. Lower Drawer 2. Open the front drawer to expose the storage compartment.
518 WHAT TO DO IN EMERGENCIES 3. Remove the liner from the console’s storage compartment to access the spare tire winch drive nut.
WHAT TO DO IN EMERGENCIES 519 6 Assembled T-handle A — Spare Tire Hook/T-handle B — Extension 1 C — Extension 2 Assembling The Spare Tire Hook A — Spare Tire Hook/T-handle B — Extension 1 C — Extension 2
520 WHAT TO DO IN EMERGENCIES 2. Rotate the nut to the left until the winch mechanism Spare Tire Removal Instructions The spare tire is located under the vehicle beneath the stops turning freely. This will allow enough slack in the center console area. cable to allow you to pull the spare tire out from underneath the vehicle. CAUTION! The winch mechanism is designed for use with the winch T-handle only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES 521 4. Stand the tire/cover assembly upright and remove the wheel spacer by squeezing the winch retaining tabs together. Push the retainer through the spare tire to release it from the wheel. 6 Pulling Spare Tire NOTE: If either front tire is flat it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle.
522 WHAT TO DO IN EMERGENCIES Preparations For Jacking 4. Place the shift lever into PARK. 1. Park the vehicle on a firm, level surface. Avoid ice or 5. Turn OFF the ignition. slippery areas. 6. Block both the front and rear of the wheel diagonally opposite the jacking WARNING! position. For example, if changing the right front tire, block the left rear Do not attempt to change a tire on the side of the wheel.
WHAT TO DO IN EMERGENCIES Jacking Instructions 523 WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
524 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. NOTE: Refer to the “Compact Spare Tire” section of “Tires – General Information” for information about the spare tire, its use, and operation. 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. Jack Locations 2.
WHAT TO DO IN EMERGENCIES 525 6 Rear Jacking Locations Front Jack Locations Front jack location is on the sill flange of the vehicle body NOTE: In some situations the jack may need to be placed on its side in order to be pushed under the vehicle. and is located 6 in (150 mm) from door edge. Return the jack to its correct orientation once it is under the vehicle.
526 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES 527 NOTE: Do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct wheel nut tightness is 102 ft lbs (138 N·m).
528 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. NOTE: Refer to the “Spare Tire Tools” section for instructions on assembling the T-handle. 12. Stow the jack, jack handle and winch handle tools back in the stowage compartment. 13.
WHAT TO DO IN EMERGENCIES WARNING! A loose compact spare tire/cover assembly, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the compact spare tire with the cover assembly in the place provided. 529 3. Turn the compact spare tire so that the valve stem is down, and place the tire into the spare tire/cover assembly.
530 WHAT TO DO IN EMERGENCIES WARNING! CAUTION! Verify that both retainer tabs of the wheel spacer have been properly extended through the center of the wheel and spare tire/cover assembly. Failure to properly engage both retainer tabs could result in loss of the spare tire and cover assembly, which will cause vehicle damage and may cause loss of vehicle control. The winch mechanism is designed specifically to stow a compact spare tire only.
WHAT TO DO IN EMERGENCIES 531 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tire And Wheel Cover Or Center Cap 1 — Valve Stem 2 — Valve Notch 3 — Wheel Lug Nut 4 — Wheel Cover 5 — Mounting Stud 5.
532 WHAT TO DO IN EMERGENCIES correct tightness, have them checked with a torque 3. Lower the vehicle to the ground by turning the jack wrench by your authorized dealer or service station. handle counterclockwise. 7. After 25 miles (40 km) check the lug nut torque with a 4. Finish tightening the lug nuts. Push down on the torque wrench to ensure that all lug nuts are properly wrench while at the end of the handle for increased seated against the wheel. leverage.
WHAT TO DO IN EMERGENCIES 533 NOTE: When using a portable battery booster pack Preparations For Jump-Start follow the manufacturer’s operating instructions and The battery in your vehicle is located on the left side of the engine compartment. precautions. CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.
534 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
WHAT TO DO IN EMERGENCIES 535 CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
536 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it cable from the positive (+) post of the booster battery. can often be moved by a rocking motion. Turn your 9. Disconnect the positive (+) end of the jumper cable steering wheel right and left to clear the area around the from the positive (+) post of the discharged vehicle. front wheels.
WHAT TO DO IN EMERGENCIES NOTE: To improve the vehicle’s traction when starting off in deep snow, sand or gravel, it may be desirable to switch the Electronic Stability Program (ESP) to “Partial Off” mode. Refer to “Electronic Brake Control System” in “Starting and Operating” for further information. CAUTION! • When “rocking” a stuck vehicle by moving between DRIVE and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.
538 WHAT TO DO IN EMERGENCIES 2. Remove the shift lever override access cover located 3. Turn the ignition switch to the ON/RUN position near the top right of the shift lever in the instrument without starting the engine. panel. 4. Press and maintain firm pressure on the brake pedal. 5. Using a small screwdriver or similar small, push and hold the override release lever forward. 6. Move the shift lever to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8.
WHAT TO DO IN EMERGENCIES 539 TOWING A DISABLED VEHICLE Towing Condition Flat Tow Wheels OFF the Ground NONE ALL MODELS If transmission is operable: • Transmission in NEUTRAL Wheel lift Flatbed Rear Front ALL • 25 mph (40 km/h)max speed • 15 miles (24 km) max distance OK BEST METHOD Proper towing or lifting equipment is required to prevent If you must use the accessories (wipers, defrosters, etc.) damage to your vehicle.
540 WHAT TO DO IN EMERGENCIES CAUTION! • Do not use sling type equipment when towing. Damage to the fascia will occur. • When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result.
WHAT TO DO IN EMERGENCIES CAUTION! Towing faster than 25 mph (40 km/h) or farther than 15 miles (24 km) with front wheels on the ground can cause severe damage to the transmission. Such damage is not covered by the New Vehicle Limited Warranty. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flatbed towing is the preferred towing method. However, if a flatbed towing vehicle is not available, wheel lift towing equipment may be used.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.6L . . . . . . . . . . . . . 545 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 552 䡵 Onboard Diagnostic System — OBD II . . . . . . 546 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 553 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 546 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 554 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
544 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission . . . . . . . . . . . . . . . 569 ▫ Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . 587 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 571 ▫ Rear Tail, Stop, Turn Signal, Side Marker And Backup Lamps . . . . . . . . . . . . . . . . . . . 588 ▫ Cleaning The Instrument Panel Cupholders . . 577 ▫ Center High-Mounted Stop Lamp (CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 545 ENGINE COMPARTMENT — 3.
546 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 547 For states that require an Inspection and Mainte“Electronic Vehicle Information Center (EVIC)” in ”Unnance (I/M), this check verifies the “Malfunction derstanding Your Instrument Panel” for further informaIndicator Light (MIL)” is functioning and is not tion. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tight- on when the engine is running, and that the OBD II system is ready for testing. ened.
548 MAINTAINING YOUR VEHICLE 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
MAINTAINING YOUR VEHICLE REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures caused by the use of non-MOPAR威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
550 MAINTAINING YOUR VEHICLE CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center.
MAINTAINING YOUR VEHICLE 551 American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has Overfilling or underfilling will cause oil aeration, or been certified by the American loss of oil pressure. This could damage your engine. Petroleum Institute (API). The manufacturer only recommends Change Engine Oil API Certified engine oils. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
552 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. Materials Added To Engine Oil The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil.
MAINTAINING YOUR VEHICLE Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine oil filters are a high quality oil filter and are recommended. Engine Air Cleaner Filter Refer to the “Maintenance Schedule” for the proper maintenance intervals.
554 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
556 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
558 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 559 WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to replace the filter: 1. Open the glove compartment and remove all contents. 2. Push in on the sides of the glove compartment and lower the door. 3. Pivot the glove compartment downward. A/C Air Filter Replacement 5.
560 MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. 561 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use.
562 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, And Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to the “Maintenance Schedule” for the proper maintenance intervals.
564 MAINTAINING YOUR VEHICLE Adding Coolant • Mix a minimum solution of 50% HOAT engine coolant Your vehicle has been built with an improved engine and distilled water. Use higher concentrations (not to coolant (antifreeze) that allows extended maintenance exceed 70%) if temperatures below ⫺34°F (⫺37°C) are intervals. This engine coolant (antifreeze) can be used up anticipated. to five years or 104,000 miles (169 000 km) before • Use only high purity water such as distilled or deionreplacement.
MAINTAINING YOUR VEHICLE Cooling System Pressure Cap The cap must be fully tightened to prevent the loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. 565 WARNING! (Continued) • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.
566 MAINTAINING YOUR VEHICLE engine cold, the level of the engine coolant (antifreeze) in normally a result of moisture from rain, snow, or high the coolant recovery bottle should be between the ranges humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot engine indicated on the bottle. coolant (antifreeze) to enter the radiator.
MAINTAINING YOUR VEHICLE • Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, also keep the front of the condenser clean.
568 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid. ReMaster Cylinder – Brake Fluid Level Check The fluid level in the master cylinder should be checked fer to “Fluids, Lubricants, and Genuine Parts” in “Mainwhen performing underhood services, or immediately if taining Your Vehicle” for further information. the “Brake System Warning Light” indicates system WARNING! failure. Clean the top of the master cylinder area before removing the cap.
MAINTAINING YOUR VEHICLE 569 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
570 MAINTAINING YOUR VEHICLE Selection Of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
MAINTAINING YOUR VEHICLE CAUTION! 571 Appearance Care And Protection From Corrosion Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
572 MAINTAINING YOUR VEHICLE The most common causes are: • Road salt, dirt and moisture accumulation • Stone and gravel impact • Insects, tree sap and tar • Salt in the air near seacoast localities • Atmospheric fallout/industrial pollutants Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water.
MAINTAINING YOUR VEHICLE Special Care 573 • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once • Use MOPAR威 Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer a month. has touch up paint to match the color of your vehicle.
574 MAINTAINING YOUR VEHICLE CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s protective finish. Use only the approved MOPAR威 Wheel Cleaners or equivalent. • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove the stain.
MAINTAINING YOUR VEHICLE Cleaning Interior Trim Interior trim should be cleaned starting with a damp cloth, a damp cloth with MOPAR威 Total Clean or equivalent, then MOPAR威 Spot & Stain Remover or equivalent if absolutely necessary. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery Cleaning Leather Upholstery MOPAR威 Total Clean or equivalent is specifically recommended for leather upholstery.
576 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. Do not use abrasive cleaning components, solvents, steel 1. Clean with a wet soft rag.
MAINTAINING YOUR VEHICLE 577 Replace the seat belts if they appear frayed or worn, or if approximately 30 minutes. After 30 minutes, pull the liner from the water and dip it back into the water about the buckles do not work properly. six times. This will loosen any remaining debris. Rinse Cleaning The Instrument Panel Cupholders the liner thoroughly under warm running water.
578 MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module The Totally Integrated Power Module is located in the engine compartment near the battery. Refer to the applicable “Engine Compartment” illustration in this section. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed or embossed on the inside of the cover.
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
580 MAINTAINING YOUR VEHICLE Cavity J8 J9 Cartridge Fuse 40 Amp Green 40 Amp Green MiniFuse — — J10 30 Amp Pink — J11 30 Amp Pink — J12 J13 30 Amp Pink 60 Amp Yellow — Description Cavity Power Memory Seat – If Equipped Partial Zero Emissions Vehicle Motor/ Flex Fuel – If Equipped Headlamp Wash/ Manifold Tuning Valve – If Equipped Power Sliding Door Module/Anti–Theft Module – If Equipped HVAC Rear Blower, Radiator Fan Motor Ignition Off Draw (IOD) – Main J14 J15 J17 J18 J19 J20 J21 J22 Cart
MAINTAINING YOUR VEHICLE M1 Cartridge Fuse — M2 — M3 — 20 Amp Yellow M4 — M5 — 10 Amp Red 25 Amp Natural Cavity MiniFuse 15 Amp Blue 20 Amp Yellow M6 Cartridge Fuse — MiniFuse 20 Amp Yellow M7 — 20 Amp Yellow M8 — M9 — 20 Amp Yellow 20 Amp Yellow Description Cavity Rear Center Brake Lamp/Brake Switch Trailer Lighting, Front Fog Lamps, Intelligent Battery Sensor (IBS) Front/Rear Axle Locker, Vacuum Pump Motor Trailer Tow Inverter 581 Description Power Outlet #1 (ACC), Rain Senso
582 MAINTAINING YOUR VEHICLE Cavity M10 Cartridge Fuse — M11 — M12 — M13 — MiniFuse 15 Amp Blue 10 Amp Red 30 Amp Green 20 Amp Yellow Description Ignition Off Draw — Video System, Satellite Radio, DVD, Hands-Free Module, Universal Garage Door Opener, Vanity Lamp, Streaming Video Module – If Equipped Climate Control System Amplifier/Radio Instrument Cluster, SIREN, Clock Module, Multi-Function Control Switch – If Equipped M14 Cartridge Fuse — M15 — M16 — 10 Amp Red M17 — 15 Amp Blue M1
MAINTAINING YOUR VEHICLE M19 Cartridge Fuse — M20 — Cavity M21 — M22 — M23 — M24 — MiniFuse 25 Amp Natural 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red 25 Amp Natural M25 Cartridge Fuse — MiniFuse 20 Amp Yellow M26 — 10 Amp Red M27 — 10 Amp Red Horn M28 — Horn M29 — Rear Wiper M30 — M31 — 10 Amp Red 10 Amp Red 15 Amp Blue 20 Amp Yellow Description Powertrain Instrument Cluster Interior Light, Switch Bank, Steering Column Module, Switch Steering Wheel Powertrain Cavit
584 MAINTAINING YOUR VEHICLE M32 Cartridge Fuse — MiniFuse 10 Amp Red M33 — M34 — 10 Amp Red 10 Amp Red Cavity M35 — 10 Amp Red Description Airbag Module, THATCHUM – If Equipped Powertrain Park Assist, Heater Climate Control Module, Headlamp Wash, Compass, Rear Camera, Door Lamps, Flashlight, Relay Diesel Cabin Heater, Rad Fan Diesel – If Equipped Heated Mirrors M36 Cartridge Fuse — MiniFuse 20 Amp Yellow M37 — 10 Amp Red M38 — 25 Amp Natural Cavity Description Power Outlet #3 (Inst
MAINTAINING YOUR VEHICLE 585 steering column. If you experience temporary or perma- REPLACEMENT BULBS nent loss of these systems, see your authorized dealer for service. LIGHT BULBS – Interior Bulb Number Center & Rear Dome Lamp . . . . . . . . . . . . . . . . . 578 VEHICLE STORAGE Center & Rear Reading Lamps . . . . . . . . . . . . . . . 578 If you are leaving your vehicle dormant for more than Front Door Courtesy Lamp. . . . . . . . . . . . . . . . . .
586 MAINTAINING YOUR VEHICLE LIGHT BULBS – Exterior Bulb Number Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H11 Fog Lamp – If Equipped . . . . . . . . . . . . . . . . PSX24W Front Side Marker, Park/ Turn Signal . . . . . . . . . . . . . . . . . . 3757A or PY27/7W Rear Tail, Stop, Turn Signal Lamp . . . . . . . . . . . . LED (Serviced at Authorized Dealer) Center High-Mounted Stop Lamp . . . . . . . . . . . . LED (Serviced at Authorized Dealer) Backup Lamp . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 587 1. From behind the bumper fascia, or the access panel on the air dam, squeeze the two tabs on the side of the bulb 1. Raise the hood to access the rear of the headlamp socket and pull straight out from the fog lamp. housing. Front Park/Turn Signal Lamps 2. Twist the turn signal socket and remove from the headlamp housing, then pull the bulb out. 3. Push the new bulb into the socket and reinstall the socket by twisting until locked into the headlamp housing.
588 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, Side Marker and Backup Lamps 1. Raise the liftgate. NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint. 2. Remove the tail lamp assembly by removing the two • The PRY location is best closest to the studs while screws from the inboard side. Use a fiber stick or similar dislodging them separately.
MAINTAINING YOUR VEHICLE 589 2. Twist and remove the socket from the lamp assembly License Lamp The license plate lamp is located under the tailgate light and pull the bulb out to remove. bar and above the license plate. 3. Push the bulb into the socket, twist the socket into the 1. Using a small screwdriver, press inward the locking lamp assembly and reinstall the lamp assembly into place tab on the outboard side of the lamp assembly and pull ensuring the locking tab is secure.
590 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your oil filler cap for correct SAE grade. MOPAR威 Engine Oil Filter or equivalent.
MAINTAINING YOUR VEHICLE 591 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product.
MAINTENANCE SCHEDULES CONTENTS 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 594 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 594 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done S anytime a malfunction is suspected.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated.
M A I N T E N A N C E 596 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals • Open the left and right door (slowly) and inspect for as required. excessive dirt. If noise exist wipe clean and apply • Check the fluid levels of the coolant reservoir, brake krytox lube to the door rollers.
MAINTENANCE SCHEDULES 8,000 Miles (13,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 597 M 16,000 Miles (26,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
M 598 MAINTENANCE SCHEDULES A I 24,000 Miles (39,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 24,000 miles (39 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 40,000 Miles (65,000 km) or 30 Months Maintenance Service Schedule 48,000 Miles (78,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer Reading Repair Order # Signature, Authorized Service Center 599 M Date Dealer Code ❏ Change the engine oil and engine oil filter.
M 600 MAINTENANCE SCHEDULES A I 56,000 Miles (91,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 56,000 miles (91 000 km). S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 72,000 Miles (117,000 km) or 54 Months Maintenance Service Schedule 80,000 Miles (130,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M 602 MAINTENANCE SCHEDULES A I 88,000 Miles (143,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 88,000 miles (143 000 km). S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 104,000 Miles (169,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ Flush and replace the engine coolant at 104,000 miles (169 000 km) or 60 months whichever comes first.
M 604 MAINTENANCE SCHEDULES A I 120,000 Miles (195,000 km) or N T 90 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 120,000 miles (195 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Change the automatic transmission fluid and filter(s).
MAINTENANCE SCHEDULES 136,000 Miles (221,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 136,000 miles (221 000 km). Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 605 M 144,000 Miles (234,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
M 606 MAINTENANCE SCHEDULES A I 152,000 Miles (247,000 km) or N T 114 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 152,000 miles (247 000 km).
MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 613 ▫ Prepare For The Appointment . . . . . . . . . . . 611 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 613 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 611 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
610 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 617 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 617 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 617 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 611 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
612 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (800) 423–6343 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
614 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 615 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
616 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC vemaintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency LLC vehicles.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 617 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
618 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
620 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . 564 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 561 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 484 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 210 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 553 Air Conditioner Maintenance . . . . . . . . . . . . . . . 557 Air Conditioning . . . . . . . . . . . . . . .
INDEX 621 Blind Spot Monitoring . . . . . . . . . . . . . . . . . . . . 117 Body Mechanism Lubrication . . . . . . . . . . . . . . . 560 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 444 Brake Control System, Electronic . . . . . . . . . . . . . 443 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 567 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . 568 Parking . . . . . . . . . . . . . .
622 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . 552 Power Steering . . . . . . . . . . . . . . . . . . . . . . 438 Radiator (Coolant Pressure) . . . . . . . . . . . . . 565 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572 Carbon Monoxide Warning . . . . . . . . . . . . . . 100,486 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 260 Cargo Compartment Luggage Carrier .
INDEX Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Universal Consumer Interface (UCI) . . . . . . . 346 Conserving Fuel . . . . . . . . . . . . . . . . . . . . . . . . 310 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Console, Floor . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Console, Overhead . . . . . . . . . . . . . . . . . . . . . . . 227 Console, Removable . . . . . . . . . . . . . . . . . . . . . . 265 Contract, Service . . . . .
624 INDEX Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . 565 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 552 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 35 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 231 Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . 434 Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . .
INDEX Flooded, Starting . . . . . . . . . . . . . . . . . . . . . 420 Fuel Requirements . . . . . . . . . . . . . . . . . 482,589 Oil . . . . . . . . . . . . . . . . . . . . . . . . . 550,589,590 Oil Change Interval . . . . . . . . . . . . . . . . . . . 551 Oil Disposal . . . . . . . . . . . . . . . . . . . . . . . . 552 Oil Filler Cap . . . . . . . . . . . . . . . . . . . . . . . 552 Oil Filter Disposal . . . . . . . . . . . . . . . . . . . . 552 Oil Selection . . . . . . . . . . . . . . . . . . . . .
626 INDEX Replacement Parts . . . . . . . . . . . . . . . . . . . . 490 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 420 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 589 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . 571 Brake . . . .
INDEX Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 Hands-Free Phone (Uconnect™) . . . . . . . . . . . . Hazard Driving Through Flowing, Rising, or Shallow Garage Door Opener (HomeLink®) . . . . . . . . . . . 231 Standing Water . . . . . . . . . . . . . . . . . . . . . Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 490,492,546 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 482 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . Conserving . . . . . .
628 INDEX . . . . . . . . . . . . . . . . . . . . . . 449 Integrated Power Module (Fuses) . . . . . . . . . . . . 578 Interior Appearance Care . . . . . . . . . . . . . . . . . . 574 . . . . . . . . . . . . . . . . . . . . . . 500 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Door Opener) Transmitter . . 231 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . . . . . . . . . 196 . . . . . . . . . . . . . . . . . . . . . .
INDEX LATCH (Lower Anchors and Tether for CHildren) . . . . . . . 90 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 482 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Light Bulbs .
630 INDEX Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . 588 Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . 588 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . 296 Security Alarm (Theft Alarm) . . . . . . . . . . . . 294 Service . . . . . . . . . . . . . . . . . . .
INDEX Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . 115,192 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 311 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Automatic Dimming . . . . . . . . . . . . . . . . . . 112 Electric Remote . . . . . . . . . . . . . . . . . . . . . . 114 Exterior Folding . . . . . . . . . . . . . . . . . . . . . 114 Heated . . . . . . . . . . . . . . . . .
632 INDEX Viscosity . . . . . . . . . . . . . . . . . . . . . . . . 552,589 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . 34 Onboard Diagnostic System . . . . . . . . . . . . . . 546,547 Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Opener, Garage Door (HomeLink®) . . . . . . . . . . . 231 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Operator Manual (Owner’s Manual) . . . . . . . . . . . . 4 Outlet (Auxiliary Electrical Outlet) . . . . . . .
INDEX Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 392 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 390 Rear Air Conditioning . . . . . . . . . . . . . . . . . 398,408 Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Rear Cross Path . . . . . . . . . . . . . . . . . . . . . . . . . 123 Rear Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 Rear Park Sense System . . . . . . . . . . . . . . . . . . . 215 Rear Window Defroster . . . .
634 INDEX Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 68 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,101 Adjustable Shoulder Belt . . . . . . . . . . . . . . . . 61 Adjustable Upper Shoulder Anchorage . . . . . . 61 And Pregnant Women . . . . . . . . . . . . . . . . . . 69 Child Restraint . . . . . . . . . . . . . . . . . . . . . 85,87 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 470 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . 465,466,516 Speed Control (Cruise Control) . . . . . . . . . . . . . . 212 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Automatic Transmission . . . . . . . . . . . . . . . . 419 Cold Weather . . . . . . . . . . .
636 INDEX Pressure Warning Light . . . . . . . . . . . . . . . . 289 Text Messaging . . . . . . . . . . . . . . . . . . . . . . . . . 147 Quality Grading . . . . . . . . . . . . . . . . . . . . . 617 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 208 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464 Tire and Loading Information Placard . . . . . . . . . 457 Replacement . . . . . . . . . . . . . . . . . . . . . . . . 469 Tire Identification Number (TIN) . . . . . . . . . .
INDEX Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 443 Traction Control Switch . . . . . . . . . . . . . . . . . . . 443 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 495 Cooling System Tips . . . . . . . . . . . . . . . . . . 508 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 Minimum Requirements . . . . . . . . . . . . . . . . 503 Trailer and Tongue Weight . . . . . . . . . . . . . . 502 Wiring . . . . . . . . . . . . . . . . . . . . . . . .
638 INDEX Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 573 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 412,585 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 41,243 Voice Recognition System (VR) . . . . . . . . . . . . . . 155 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 412 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Power . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2012 RAM CARGO VAN 2012 OWNER’S MANUAL Chrysler Group LLC 12MZZ-126-AA 1199168 Ram Truck 1500-2500-3500 OM cover.indd 1 First Edition RAM CV C a r g o Va n Printed in U.S.A.
