2013 Chrysler Group LLC 13DD43-126-AA 3500/4500/5500 OWNER’S MANUAL First Edition Printed in U.S.A. 1135811cv1 13DD43-126-AA Chassis Cab Chrysler 1" gutter 09/13/2012 13:48:58 2013 CHASSIS CAB CHASSIS CAB 2013 OWNER’S MANUAL Chrysler Group LLC 13DD43-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VAN CONVERSIONS/CAMPERS . . . . . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .6 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine MOPAR威 parts, and cares about LLC vehicle. Be assured that it represents precision your satisfaction. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury.
INTRODUCTION 7 frame and underbody as well as the Automobile Infor- VEHICLE MODIFICATIONS/ALTERATIONS mation Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . ▫ Ignition System . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ▫ To Arm The System . . . . . . . . . . . . . . . ▫ Removing Key Fob From Ignition . . . . . . . . . .16 ▫ To Disarm The System . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .26 䡵 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .27 ▫ Power Windows – If Equipped . . . . . . . . . . . .38 ▫ Programming Additional Transmitters. . . . . . . .28 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .41 ▫ Transmitter Battery Replacement . . . . . . . . . . .28 䡵 KEYLESS ENTER-N-GO™ . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Enhanced Seat Belt Use Reminder System 䡵 ENGINE BREAK-IN RECOMMENDATIONS . . .110 (BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . .60 䡵 DIESEL ENGINE BREAK-IN ▫ Seat Belts And Pregnant Women . . . . . . . . . . .61 RECOMMENDATIONS . . . . . . . . . . . . . . . . . .110 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .61 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition System Fob with Remote Keyless Entry (RKE) — If Equipped Your vehicle may be equipped with either an Ignition Node Module (IGNM) which operates similar to a standard ignition switch, or a Keyless Ignition Node (KIN) which allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Keyless Ignition Node (KIN) — If Equipped This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START, during start RUN will illuminate.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. 2 The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition Place the shift lever in PARK (if equipped with an automatic transmission). Turn the Key Fob to the OFF position and then remove the Key Fob. NOTE: Emergency Key Removal Keyless Enter-N-Go™ Fob (KIN) NOTE: You can insert the double-sided emergency key into the lock cylinder with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. CAUTION! • If your vehicle battery becomes low or dead, your Key Fob will become locked in the ignition. • Do not attempt to remove the Key Fob while in this condition, damage could occur to the Key Fob or ignition module. Only remove the emergency key for locking and unlocking the doors.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a Key Fob with a factory-mated Remote Keyless Entry (RKE) transmitter and an Ignition Node Module (IGNM) to prevent unauthorized vehicle operation.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended. • For vehicles equipped with Keyless Enter-N-Go™, always remember to place the ignition in the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: When having the Sentry Key威 Immobilizer VEHICLE SECURITY ALARM — IF EQUIPPED System serviced, bring all vehicle keys with you to an The Vehicle Security Alarm monitors the vehicle doors authorized dealer. and ignition for unauthorized operation. When the Vehicle Security Alarm is activated, interior switches for Customer Key Programming door locks are disabled.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Security Alarm will also disarm if a programmed Sentry Key威 is inserted into the ignition The Vehicle Security Alarm will set when you use the switch. To exit the alarming mode, press the RKE transpower door locks, or use the Remote Keyless Entry (RKE) mitter UNLOCK button, or insert a programmed Sentry transmitter to lock the doors. After all the doors are Key威 into the ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • The illuminated entry system will not operate if the dimmer control is in the “Dome OFF” position (rotate The courtesy lights will turn on when you use the horizontal thumb wheel on the bottom of the switch to Remote Keyless Entry (RKE) transmitter to unlock the the far left detent position). doors or open any door. ILLUMINATED ENTRY — IF EQUIPPED This feature also turns on the approach lighting in the outside mirrors (if equipped).
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Inserting the Key Fob with RKE transmitter into the ignition switch disables the system from responding to any button presses from that RKE transmitter. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmitter buttons for all RKE transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmitfollowing procedure: ter while you are inside the vehicle will activate the Vehicle Security Alarm System. Opening a door with the 1. Press and hold the LOCK button on a programmed Vehicle Security Alarm System activated will cause the RKE transmitter for at least four seconds, but no alarm to sound.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the sound. Press the UNLOCK button to deactivate the following procedure: Vehicle Security Alarm System. 1. Press and hold the UNLOCK button on a programmed RKE transmitter for at least four seconds, but no longer than ten seconds. Then, press and hold the LOCK button while still holding the UNLOCK button. To Lock The Doors Press and release the LOCK button on the RKE transmitter to lock all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • For vehicles not equipped with the EVIC, perform the Security Alarm System activated will cause the alarm to following procedure: sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm System. 1. Press the LOCK button on a programmed RKE transmitter for at least four seconds, but no longer than Using The Panic Alarm ten seconds.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: NOTE: • The interior lights will turn off if you turn the ignition • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate switch to the ACC or ON/RUN position while the Panic Alarm is activated. However, the exterior lights • Do not touch the battery terminals that are on the back and horn will remain on. housing or the printed circuit board. • You may need to be less than 35 ft (11 m) from the 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB This device complies with Part 15 of the FCC rules and radios. RSS 210 of Industry Canada. Operation is subject to the following conditions: REMOTE STARTING SYSTEM — IF EQUIPPED General Information • This device may not cause harmful interference.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • HAZARD switch off • BRAKE switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed • Fuel meets minimum requirement • System not disabled from previous remote start event • Vehicle theft alarm not active W
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • Remote Start Aborted — Hood Ajar NOTE: • Remote Start Aborted — Fuel Low • If your power door locks were unlocked, Remote Start will automatically lock the doors. • Remote Start Aborted — System Fault • Remote Start Disabled — Start Vehicle to Reset • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the message “Insert Key/ Turn To On” will flash in the EVIC until you insert the Press and release the REMOTE START button one time or Key Fob into the ignition switch. Once inserted, the allow the engine to run for the entire 15-minute cycle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is turned to the ON/RUN position. 2 The Remote Start Comfort System can be activated and deactivated through the Electronic Vehicle Information Center (EVIC).
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The emergency key will unlock the driver door lock on your vehicle. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • For personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 to operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob. Automatic Door Locks — If Equipped When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer . Please see your authorized dealer for service.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Doors Programming — If Equipped Child-Protection Door Lock The Auto Unlock Doors feature can be enabled or dis- To provide a safer environment for children riding in the abled as follows: rear seat, the rear doors (if equipped) of your vehicle have the Child-Protection Door Lock system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to engage and disengage the Child-Protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. WARNING! Avoid trapping anyone in a vehicle in a collision.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows – If Equipped The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the Crew Cab models.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To stop the window from going all the way up during the Reset Auto-Up Auto Up operation, push down on the switch briefly. Should the Auto Up feature stop working, the window To close the window part way, lift the window switch to the probably needs to be reset. To reset Auto Up: first detent and release when you want the window to stop. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 controls, press the window LOCK button again and Wind Buffeting return the switch to the released or up position. Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To Unlock From The Driver’s Side: • Passive Entry may be programmed ON/OFF; refer to With a valid Passive Entry RKE transmitter within 5 ft “Uconnect威 settings” in “Understanding Your Instru- (1.5 m) of the driver door handle, grab the front driver door handle to unlock the driver’s door automatically. ment Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press”, refer to “Uconnect威 Settings” in “Understanding Your Instrument Panel” for further information.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Vehicle’s Doors With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, press the door handle LOCK button to lock all doors. Do NOT grab the door handle, when pressing the door handle lock button. This could unlock the door(s).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • The Passive Entry system will not operate if the RKE transmitter battery is dead.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you will be carrying children too small for adult-sized Some of the most important safety features in your seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold vehicle are the restraint systems: infant and child restraint systems. For further informa• Three-point lap and shoulder belts for the driver and tion, refer to “Lower Anchors and Tether for CHildren all passengers (LATCH)”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger Advanced Front Air Bag. An air bag deployment can cause severe injury or death to infants in that position. If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (Refer to “Child Restraints”).
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags. • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air Bags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Pulling Out Latch Plate And Webbing 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Regular Cab Front Center Three Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the seat belt tongue into the center red slot on the black buckle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 2 Inserting Latch Plate In Use Position
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Center Lap Belts The center seating position for the Crew Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a ⬙click.⬙ To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing. Wear the lap belt snug against the hips. Sit back and erect in the seat, then adjust the belt as tightly as is comfortable.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts In Passenger Seating Positions Crew Cab姞 Left Center Right The seat belts in the passenger seating positions are equipped with an Automatic Locking Retractor (ALR) or First Row N/A Cinch ALR a cinching latch plate which are used to secure a child Second Row ALR Cinch ALR restraint system. For additional information refer to “Installing Child Restraints Using the Vehicle Seat Belt” • N/A — Not Applicable under the “Child Restraint” section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode Enhanced Seat Belt Use Reminder System Unbuckle the combination lap and shoulder belt and (BeltAlert姞) allow it to retract completely to disengage the Automatic BeltAlert威 is a feature intended to remind the driver and Locking mode and activate the vehicle sensitive (emer- front passenger (if equipped with front passenger BeltAlert威) to fasten their seat belts. The feature is active gency) locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 unbuckled while traveling at speeds greater than 5 mph Seat Belts And Pregnant Women (8 km/h), BeltAlert威 will provide both audio and visual We recommend that pregnant women use seat belts notification. throughout their pregnancies. Keeping the mother safe is The front passenger seat BeltAlert威 is not active when the the best way to keep the baby safe. front passenger seat is unoccupied.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The Advanced Front Air Bags have a multistage inflator Air Bag System Components design. This allows the air bag to have different rates of Your vehicle may be equipped with the following air bag inflation based on several factors, including the severity system components: and type of collision.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front passenger (if equipped) air bags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC). The first stage inflator is triggered immediately during an impact that requires air bag deployment. This low output is used in less severe collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts in The Knee Impact Bolster helps protect the knees of the certain frontal collisions depending on several factors, front passenger, and position the front occupant for the including the severity and type of collision. Advanced best interaction with the Advanced Front Air Bag.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat belts are necessary for your protection in all colli- turns on the Air Bag Warning Light, either momentarily sions, and also are needed to help keep you in position, or continuously. A single chime will sound if the light comes on again after initial startup. away from an inflating air bag. The ORC monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Driver And Passenger (if equipped) Advanced Front Air Bag Inflator Units The Driver and Passenger (if equipped) Advanced Front Air Bag Inflator Units are located in the center of the steering wheel and on the right side of the instrument panel. When the ORC detects a collision requiring the Advanced Front Air Bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Advanced Front Air Bags.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In order to reset the Enhanced Accident Response System 3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit functions after an event, the ignition switch must be the following important vehicle information to a 9-1-1 changed from IGN ON to IGN OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 to speak with you or other vehicle occupants and hear sounds occurring in the vehicle. The vehicle’s 9-1-1 Call system will attempt to remain connected with the 9-1-1 operator until the 9-1-1 operator terminates the connection. 5. The 9-1-1 operator may attempt to contact appropriate emergency responders and provide them with important vehicle information and GPS coordinates. WARNING! • If anyone in the vehicle could be in danger (e.g.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9-1-1 Call System Limitations Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system capabilities. 9-1-1 or other emergency line operators in Canada and Mexico may not answer or respond to 9-1-1 system calls.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • The ignition key is in OFF position; NOTE: Never place anything on or near the vehicle’s wireless and GPS antennas. You could prevent wireless • The vehicle’s electrical systems are not intact; and GPS signal reception, which can prevent your vehicle • The 9-1-1 Call system software and/or hardware are from placing an emergency call. Wireless and GPS signal damaged during a crash; reception is required for the 9-1-1 Call system to function properly.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Advanced Front Air Bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the following may occur: bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check You will want to have the air bags ready to the fuse block for blown fuses. Refer to the label located inflate for your protection in a collision. The on the inside of the fuse block cover for the proper air bag Air Bag Warning Light monitors the internal fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 • How far (if at all) the driver was depressing the In addition to the vehicle manufacturer, other parties, accelerator and/or brake pedal; and, such as law enforcement, that have the special equipment, can read the information if they have access to the • How fast the vehicle was traveling. vehicle or the EDR. These data can help provide a better understanding of Child Restraints the circumstances in which crashes and injuries occur.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to make sure you have the correct seat for your child. Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight or Age Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rearfacing child restraint Children who have out-gro
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5. Can the child stay seated like this for the whole trip? over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Recommendations For Attaching Child Restraints — Quad Cab威/Crew Cab Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints — Standard Cab, Mega Cab威 Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Quad Cab威/Crew Cab Full Bench Standard Cab Lower Anchorage Symbol 2 anchorages per seating Lower Anchorage Symbol 2 anchorages per seating position position Top Tether Anchorage Symbol Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 2 Quad Cab威/Mega Cab威/Crew Cab Split Bench Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab威/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No Never “share” a LATCH anchorage with two or more child restraints.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab威/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Can the LATCH anchorages and the seat belt be used together to attach a rear-facing or forward-facing child restraint? No Use the LATCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No Never “share” a LATCH anchorage with two or more child restraints.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages — Quad Cab威/Mega Cab威/Crew Cab The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Cab models have tether strap anchorages located behind each of the rear seats. 2 Mega Cab威 Tether Strap Mounting (Behind Covers) Regular Cab Tether Strap Mounting 1 — Tether Strap Hook 2 — Tether Strap to Child Restraint 3 — Tether Anchor LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE anchorage. Forward-facing child restraints and some rear-facing infant restraints will also be equipped with a tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Always follow the directions of the child restraint manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Always follow the directions of the child restraint manu- 3. Place the child seat between the lower anchorages for that seating position. For some second row seats, you facturer when installing your child restraint. Not all child may need to recline the seat and / or raise the head restraint systems will be installed as described here. restraint to get a better fit. To Install A LATCH-compatible Child Restraint 4.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child’s reach. If the buckled seat belt interferes with the child restraint installation, instead of buckling it behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the 7.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Installing Child Restraints Using The Vehicle Seat Belt The seat belts in the passenger seating positions are equipped with either a Switchable Automatic Locking Retractor (ALR) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle Quad Cab威/Mega Cab威/Crew Cab Standard Cab
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Quad Cab威/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Yes Always us
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab威/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Installing A Child Restraint with a Switchable Automatic Locking Retractor (ALR) back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 1. Place the child seat in the center of the seating position. For some second row seats, you may need to 6. Try to pull the webbing out of the retractor.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by 3. Slide the latch plate into the buckle until you hear a “click.” pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) 4. Finally, pull up on any excess webbing to tighten the in any direction.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Any seat belt system will loosen with time, so check the facing out, away from the child restraint. Repeat steps 4 belt occasionally, and pull it tight if necessary. to 6, above, to complete the installation of the child restraint. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have If the belt still cannot be tightened after you shorten the trouble tightening the seat belt.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Top Tether Anchorage Regular and Mega Cab威 Trucks: In the regular cab truck, the top tether anchorages are located behind the center and right passenger seats. In the mega cab truck, the top tether anchorages are located behind each rear seating position. There is a plastic cover over each anchorage. To attach the tether strap of the child restraint: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head restraint and between its posts. 2 3. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never place a rear facing infant seat in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. Right or Left Outboard Seats: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the center tether strap loop. Tether Strap Loop With Center Head Restraint In Raised Position 2.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the hook to the center tether strap loop (see NOTE: If there are child seats in both of the outboard diagram). Tighten the tether strap according to the (left and right) seating positions, the tether strap hooks of child seat manufacturer’s instructions. both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats. Center Seat: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the right or left outboard tether strap loop. Tether Strap Loop With Head Restraint In Raised Position 2.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the hook to the outboard tether strap loop (see Installing Three Child Restraints: diagram). Tighten the tether strap according to the 1. Place a child restraint on each outboard rear seat. child seat manufacturer’s instructions. Route the tether straps following the directions for right and left seating positions, above. 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 • Use the appropriate transmission gear to prevent loaded operating conditions which allow the engine engine lugging. parts to achieve final finish and fit during the first • Observe vehicle oil pressure and temperature 6,000 miles (10 000 km). indicators. SAFETY TIPS • Check the coolant and oil levels frequently.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 WARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .121 ▫ Automatic Dimming Mirror — If Equipped . . .122 ▫ Automatic Dimming Mirror With Rear View Camera Display — If Equipped . . . . . . . . . . .123 ▫ “Slide-On-Rod” Features Of Sun Visor — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .127 ▫ Trailer Towing Mirrors — If Equipped . . . . . .128 䡵 SEATS . . . . . . .
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ 40-20-40 Front Bench Seat — If Equipped . . . .136 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .137 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .139 ▫ Programming The Memory Feature . . . . . . . . .140 ▫ Linking And Unlinking The Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . . .141 ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . .147 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .155 䡵 ELECTRONIC SPEED CONTROL . . . . . . . . . . .163 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . .155 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .164 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .156 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .164 ▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . .156 ▫ To Deactivate . . . . . . . . . . . . .
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .174 ▫ Storage (Regular Cab) . . . . . . . . . . . . . . . . . .180 ▫ Front Seat Cupholders — (40–20–40 Seats) . . . .174 ▫ Storage and Seats (Crew Cab) . . . . . . . . . . . . .181 ▫ Front Instrument Panel Cupholders — Floor Storage Bin . . . . . . . . . . . . . . . . . . . . . . . . . .174 ▫ Plastic Grocery Bag Retainers (Regular Cab Models) . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Automatic Dimming Mirror With Rear View Camera Display — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. 3 Power Mirror Controls 1 — Mirror Select Buttons 2 — Four-Way Mirror Control Switch Power Mirror Controls Location The power mirror controls consist of mirror select but- To adjust a mirror, press either the L (left) or R (right) button to select the mirror that you want to adjust. tons and a four-way mirror control switch.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the mirror control switch, press on any of the four Heated Mirrors — If Equipped arrows for the direction that you want the mirror to move These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster if equipped. Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position. 3 Illuminated Vanity Mirror “Slide-On-Rod” Features Of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Fold the trailer towing mirrors rearward prior to These mirrors are designed with an adjustable mirror entering an automated car wash. head to provide a greater vision range when towing A small blindspot mirror is located next to main mirror extra-wide loads. To change position inboard or out- and can be adjusted separately. board, the mirror head should be rotated (flipped in or out).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 SEATS WARNING! (Continued) Seats are a part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Power Seat — If Equipped Some models may be equipped with an eight-way power driver’s seat. The power seat switches are located on the outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the movement of the seat cushion and the seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions. Pull upward or push downward on the front or rear of the seat switch, the front or rear of the seat cushion will move in the direction of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Power Lumbar — If Equipped Heated Seats — If Equipped Vehicles equipped with power driver or passenger seats On some models, the front and rear seats may be may be also be equipped with power lumbar. The power equipped with heaters located in the seat cushions. lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the WARNING! lumbar support. Push the switch rearward to decrease the lumbar support.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Heated Seats • The engine must be running for the heated seats to operate. On some models, the two outboard seats are equipped with heated seats. The heated seat switches for these When the HIGH-level setting is selected, the heater will seats are located on the rear of the center console. provide a boosted heat level during the first four minutes of operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 The ventilated seat switches are located in the switch bank in the center stack of the instrument panel just below the climate controls as well as soft keys located in the radio screen. The fans operate at two speeds, HIGH and LOW. NOTE: The engine must be running for the ventilated seats to operate.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be Both front seats are adjustable forward or rearward. The sure that the seat adjusters have latched. manual seat adjustment handle is located under the seat cushion at the front edge of each seat. Manual Seat Adjuster — If Equipped WARNING! • Adjusting a seat while driving may be dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 On some models the back of the center portion (20%) Reclining Rear Seats — If Equipped easily folds down to provide an armrest/center storage The recliner handle is located on the outside of the seat compartment. cushion. To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach Head Restraints the desired position, release the handle.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Rear Head Restraints The outboard head restraints can be adjusted. To raise the head restraint, pull upward on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, adjustable pedals (if equipped) and a set of desired radio station presets. Your Remote Keyless Entry (RKE) transmitter can also be programmed to recall the same positions when the UNLOCK button is pressed.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming The Memory Feature Vehicles Not Equipped With Keyless Enter-N-Go NOTE: To create a new memory profile, perform the 1. Insert the ignition key fob, and turn the ignition switch following: to the ON/RUN position. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • The Recall Memory with Remote Linked to Memory To program your RKE transmitters, perform the following: feature can be enabled through the Electronic Vehicle 1. Remove the Key Fob from the ignition (or change the Information Center (EVIC), refer to “Electronic Vehicle ignition to OFF, for vehicles equipped with Keyless Information Center (EVIC)/Customer-Programmable Enter-N-Go). Features” in “Understanding Your Instrument Panel” 2.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memory Position Recall Driver Two Memory Position Recall NOTE: The vehicle must be in PARK to recall memory • To recall the memory setting for driver two using the positions. If a recall is attempted when the vehicle is not memory switch, press MEMORY button number 2 on in PARK, a message will be displayed in the Electronic the memory switch. Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Your vehicle is equipped with plastic headlight and fog Headlights light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as To turn on the headlights, rotate the headlight scratch resistant as glass and therefore different lens switch clockwise to the headlight position. cleaning procedures must be followed.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the system is on, the Headlight Delay feature is This system automatically turns the headlights on or off also on. This means the headlights will stay on for up to according to ambient light levels. To turn the system on, 90 seconds after you turn the ignition switch to the OFF position. To turn the automatic headlights off, turn the rotate the headlight switch to the AUTO position. headlight switch out of the AUTO position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 on, and then the headlight switch is cycled off. Headlight delay can be cancelled by either turning the headlight The headlights on your vehicle will illuminate when the switch on then off, or by turning the ignition ON. engine is started and the transmission is in any gear except PARK. This provides a constant ⬙Lights ON⬙ The headlight delay time is programmable on vehicles condition until the ignition is turned OFF.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Rotate the headlight switch counterclockwise to the AUTO (A) position. • SmartBeam™ can be turned on or off using the Uconnect威 System, refer to “Uconnect威 Settings” in “Understanding 3. Push the multifunction lever away from you to switch the Your Instrument Panel” for further information. headlights to the high beam position. Refer to “Multifunction Lever” in this section for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 3. Rotate the headlight switch clockwise from the AUTO (A) to the on position. Parking Lights And Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the O (Off) position.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. If the headlights remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel as well as the ambient lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer).
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. Rear Passenger Courtesy/Reading Light Front Courtesy/Reading Lights NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Ambient Light Cargo Light The overhead console is equipped with an ambient light The cargo lights are turned on by pressing on the cargo feature. This light casts illumination for improved visibil- button. ity of the floor console area. 3 Cargo Light Switch Ambient Light The cargo lights will also turn on for approximately 30 seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry feature.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever is located on the left side of the steering column. Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Turn Signal Lever NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Lane Change Assist High/Low Beam Switch Tap the lever up or down once, without moving beyond Push the multifunction lever toward the instrument the detent, and the turn signal (right or left) will flash panel to switch the headlights to high beam. Pulling the three times then automatically turn off. multifunction lever back toward the steering wheel will turn the low beams back on, or shut the high beams off.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Windshield Wiper Operation Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. The wipers and washers are operated by a switch in the Rotate the end of the lever upward to the second detent multifunction lever. Turn the end of the handle to select past the intermittent settings for high-speed wiper operathe desired wiper speed. tion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Windshield Washers To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed and the wiper will operate for two to three cycles after the washer knob is released from this position. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers — If Equipped NOTE: This feature senses moisture on the windshield and • The Rain Sensing feature will not operate when the automatically activates the wipers for the driver. The wiper switch is in the low or high-speed position. feature is especially useful for road splash or overspray • The Rain Sensing feature may not function properly from the windshield washers of the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 The Rain Sensing system has protection features for the Remote Start Mode Inhibit — On vehicles equipped wiper blades and arms, and will not operate under the with Remote Starting system, Rain Sensing wipers are not operational when the vehicle is in the remote start following conditions: mode.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”. NOTE: • Always adjust the pedals to a position that allows full pedal travel. • Further small adjustments may be necessary to find the best possible seat/pedal position. CAUTION! Adjustable Pedals Switch • The pedals can be adjusted with the ignition OFF.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 WARNING! The Electronic Speed Control buttons are located on the right side of the steering wheel. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory. To Resume Speed To decrease speed while the Electronic Speed Control is set, push the SET (-) button. If the button is continually held in the SET (-) position, the set speed will continue to decrease until the button is released.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Electronic Speed Control system maintains OVERHEAD CONSOLE — IF EQUIPPED speed up and down hills. A slight speed change on The overhead console is located on the headliner above moderate hills is normal. the review mirror. The overhead console contains the On steep hills, a greater speed loss or gain may occur so following features: it may be preferable to drive without Electronic Speed • Courtesy/Reading Lights Control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Courtesy/Reading Lights Both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON/RUN or ACC positions for the outlet to provide power.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Center console when equipped with bucket seats. • Inside the upper lid of the center storage compartment — if equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 • Rear of the center console storage compartment — All accessories connected to the outlet(s) should be Quad Cab威 or Crew Cab. removed or turned off when the vehicle is not in use to protect the battery against discharge. WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 For vehicles equipped with a floor console the cupholders may be used. POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. Front Instrument Panel Cupholders — Floor Storage Bin For vehicles equipped with bucket seats two cupholders are located in the floor storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage The glove box is located on the passenger side of the located in the center armrest. instrument panel and features both an upper and lower storage area.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Door Storage Rear Door Storage — Crew Cab Front Door Storage — If Equipped Storage compartments are located in both the driver and passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 3 Upper Storage Compartment With the upper lid closed, pull on the lower handle to open the lower storage bin.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 3 Storage Bin Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Crew Cab Storage CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .187 ▫ EVIC White Telltales . . . . . . . . . . . . . . . . . . .209 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . . .188 ▫ EVIC Red Telltales . . . . . . . . . . . . . . . . . . . . .209 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .189 ▫ EVIC Green Telltales . . . . . . . . . . . . . . . . . . .211 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . .
186 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Uconnect威 ACCESS RADIOS — IF EQUIPPED . .239 䡵 iPod威/USB/MP3 CONTROL — IF EQUIPPED . .239 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .240 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .241 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .241 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . . .241 䡵 RADIO OPERATION AND MOBILE PHONES . .242 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 187 INSTRUMENT PANEL FEATURES 4 1 — Headlight Switch 2 — Instrument Cluster 3 — Radio 4 — Hazard Switch 5 — Upper Glove Compartment 6 — Lower Glove Compartment 7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank (Engine Start/Stop, ESC OFF, TOW/HAUL, Electronic Trailer Brake, Air Suspension, Park Assist) — If Equipped 10 — Instrument Panel Drawer 11 — Climate Controls 12 — Power Outlet/Cigar Lighter 13 — Gear Selector/Transfer Case Position Switch
188 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 189 If the ABS light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is 1. Tachometer not functioning and that service is required. However, The tachometer indicates engine speed in Revolutions the conventional brake system will continue to operate Per Minute (RPM x 1000). normally if the BRAKE warning light is not on.
190 UNDERSTANDING YOUR INSTRUMENT PANEL come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condition investigated promptly. If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Check for an inoperative outside light bulb if either 6. Brake Warning Light indicator remains on and does not flash, or flashes at a This light monitors various brake functions, rapid rate. including brake fluid level and parking brake 5. Voltmeter application.
192 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 The light also will turn on when the parking brake is After the bulb check or when driving, if the driver’s seat applied with the ignition switch in the ON/RUN position. belt remains unbuckled, the seat belt reminder light will flash or remain on continuously. Refer to “Occupant NOTE: This light shows only that the parking brake is Restraints” in “Things To Know Before Starting Your applied. It does not show the degree of brake application.
194 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Oil Pressure Warning Light 12. Park/Headlight ON Indicator — If Equipped This indicator will illuminate when the park This light indicates low engine oil pressure. The lights or headlights are turned on. light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will 13. Cargo Light — If Equipped sound for four minutes when this light turns on.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 16. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
196 UNDERSTANDING YOUR INSTRUMENT PANEL alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 NOTE: The highest available transmission gear is dis- 22. TOW/HAUL played in the lower right corner of the Electronic Vehicle The TOW HAUL button is located on the center Information Center (EVIC) whenever the Electronic stack upper switch bank. This light will illumiRange Select (ERS) feature is active. Use the +/- selector nate when TOW HAUL mode is selected. on the shift lever to activate ERS.
198 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, The “ESC Off Indicator Light” and the “ESC Activation/ or when towing a trailer. It should not be allowed to Malfunction Indicator Light” come on momentarily each exceed the upper limits of the normal operating range. time the ignition switch is turned to ON/RUN.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 WARNING! ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle.” Follow the warnings under the “Cooling System Pressure Cap” paragraph.
200 UNDERSTANDING YOUR INSTRUMENT PANEL This system allows the driver to select a variety of useful The system allows the driver to select information by information by pressing the switches mounted on the pressing the following buttons mounted on the steering steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 • UP Arrow Button Press and release the UP arrow button to scroll upward through the main menu and submenus (Fuel Economy, Trip A, Trip B, Audio, Stored Messages, Screen Set Up). • DOWN Arrow Button • SELECT/RIGHT Arrow Button Press and release the SELECT/RIGHT arrow button to access/select the information screens or sub-menu screens of a main menu item.
202 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays The EVIC displays are located in the center portion of the cluster and consists of eight sections: 1. Main Screen — The inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings and white for on demand information. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 8. 4WD Status 9. Selectable Gauge 2 10. Selectable Gauge 1 The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages. These pop up messages fall into several categories: • Five Second Stored Messages the EVIC’s compass/outside temp line.
204 UNDERSTANDING YOUR INSTRUMENT PANEL seconds and then returns to the previous screen. An message temporarily, press and release the MENU butexample of this message type is “Automatic High ton. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the Beams On”. following procedure. Engine Oil Change Indicator System Vehicles Equipped With Keyless Enter-N-Go™ Oil Change Required 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 2. Fully depress the accelerator pedal, slowly, three times • within 10 seconds. • 3. Turn the ignition switch to the OFF/LOCK position. • NOTE: If the indicator message illuminates when you • start the vehicle, the oil change indicator system did not • reset. If necessary, repeat this procedure.
206 UNDERSTANDING YOUR INSTRUMENT PANEL • Brake Fluid Low • Remote Start Active Push Start Button • Service Electronic Braking System • Remote Start Aborted Fuel Low • Engine Temperature Hot • Remote Start Aborted Too Cold • Battery Voltage Low • Remote Start Aborted Door Open • Service Electronic Throttle Control • Remote Start Aborted Hood Open • Lights On • Remote Start Aborted Trunk Open • Right Turn Signal Light Out • Remote Start Aborted Time Expired • Left Turn Signal Light Out • Remo
UNDERSTANDING YOUR INSTRUMENT PANEL 207 • Door Open • Transmission Too cold Idle with Engine On • Doors Open • Washer Fluid Low • Gear Not Available • Shift Not Allowed The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. • Shift to Neutral then Drive or Reverse EVIC Amber Telltales • Autostick Unavailable Service Required • Automatic Unavailable Use Autostick Service Req.
208 UNDERSTANDING YOUR INSTRUMENT PANEL • Low Coolant Level Indicator This telltale will turn on to indicate the vehicle coolant level is low. • Loose Gascap Indicator If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the telltale display area.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. EVIC White Telltales • Electronic Speed Control Ready EVIC Red Telltales This area will show reconfigurable red telltales. These telltales include: • Door Ajar This light will turn on to indicate that one or more doors may be ajar.
210 UNDERSTANDING YOUR INSTRUMENT PANEL • Charging System Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an authorized dealer. check.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 chime will sound after reaching a set threshold. Further EVIC Green Telltales overheating will cause the temperature gauge to pass H, • Electronic Speed Control SET the indicator will continuously flash and a continuous This telltale will illuminate green when the chime will occur until the engine is allowed to cool. electronic speed control is SET.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Digital Speedometer Vehicle Info (Customer Information Features) Press and release the UP or DOWN arrow Press and release the UP or DOWN arrow button until the Digital display icon is highbutton until the Vehicle Info icon is highlighted lighted in the EVIC. Press and release the in the EVIC. Press and release the SELECT/ SELECT/RIGHT arrow button to change the RIGHT arrow button and Coolant Temp will be display between km/h and mph. displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Press and release the UP or DOWN arrow button until Refer to “Tire Pressure Monitoring System (TPMS)” “Tire Pressure” is highlighted in the EVIC. Press and under “Starting and Operating” for further information. release the SELECT/RIGHT arrow button and one of the Trip A following will be displayed: If tire pressure is OK for all tires a vehicle ICON is displayed with tire pressure values in each corner of the ICON.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Trip B Fuel Economy Press and release the UP or DOWN arrow button until the Trip B icon is highlighted in the EVIC. The Trip B information will display the following: Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Trailer Tow Screen Setup Press and release the UP or DOWN arrow Press and release the UP or DOWN arrow button until the Trailer Tow icon is highlighted. button until the Screen Setup display icon is Press the SELECT/RIGHT arrow button and highlighted in the EVIC. Press and release the the next screen will display the following SELECT/RIGHT arrow button to enter the trailer trip information: Screen Setup sub-menu.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the SELECT/RIGHT arrow button to Language display one of the following choices. When in this display you may select one of six languages For vehicles equipped with a 7” EVIC screen and not for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the UP or equipped with a Uconnect威 Access 8.4 radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 been selected. Refer to “Rear Park Assist System” in “Understanding The Features Of Your Vehicle” for sysWhen this feature is selected, the navigation system tem function and operating information. utilizes voice commands, guiding through the drive route, mile by mile, turn-by-turn until the final destina- Tilt Mirror In Reverse tion is reached.
218 UNDERSTANDING YOUR INSTRUMENT PANEL check-mark is removed showing the system has been then press and release the SELECT button until a checkdeactivated. When the system is deactivated, the system mark appears next to the setting, showing that the setting has been selected. reverts to the standard intermittent wiper operation. Hill Start Assist (HSA) Illuminated Approach When on is selected, the HSA system is active.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 a check-mark appears next to the feature showing the showing the system has been activated, or the checksystem has been activated or the check-mark is removed mark is removed showing the system has been deactivated. showing the system has been deactivated. Automatic High Beams — If Equipped Flash Lamps With Lock When this feature is selected, the high beam headlights will deactivate automatically under certain conditions.
220 UNDERSTANDING YOUR INSTRUMENT PANEL feature showing the system has been activated, or the feature showing the system has been activated or the check-mark is removed showing the system has been check-mark is removed showing the system has been deactivated. deactivated. Auto Unlock Doors Sound Horn With Remote Lock When this feature is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is opened.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 When Unlock All Doors On 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
222 UNDERSTANDING YOUR INSTRUMENT PANEL your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Trailer Brake Type Calibrate Compass When this feature is selected, the Trailer Brake Type can be changed between “Light Electric”, “Heavy Electric”, “Light EOH” and “Heavy EOH”. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. Refer to “Integrated Trailer Brake Module” in “Starting And Operating.
224 UNDERSTANDING YOUR INSTRUMENT PANEL • Time • Oil Temp • Range To Empty (RTE) • Time • Average MPG • Range To Empty (RTE) • Current MPG • Average MPG • Trip A • Current MPG • Trip B • Trip A • Trailer Trip (distance only) • Trip B • Trailer Brake Gain • Trailer Trip (distance only) Upper Right • Trailer Brake Gain • None Lower Left • Compass (default setting) • None (default setting) • Outside Temp • Compass • Trans Temp • Outside Temp
UNDERSTANDING YOUR INSTRUMENT PANEL 225 • Trans Temp • Time • Oil Temp • Range • Time • AVG MPG • Range • Current MPG • AVG MPG • Trailer Brake Gain • Current MPG Restore To Defaults (Restores All Settings To Default Settings) • Trailer Brake Gain Lower Right • None (default setting) • Cancel • Okay • Compass Uconnect姞 ACCESS SETTINGS • Outside Temp The Uconnect威 Access system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access a
226 UNDERSTANDING YOUR INSTRUMENT PANEL Hard-Keys Soft-Keys Hard-Keys are located below the Uconnect威 Access system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), press the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
UNDERSTANDING YOUR INSTRUMENT PANEL 227 next to the setting, showing that setting has been selected. Once the setting is complete either press the Back Arrow soft-key or the Back hard-key to return to the previous menu or press the X soft-key to close out of the settings screen. Pressing the Up or Down Arrow soft-keys on the right side of the screen will allow you to toggle up or down through the available settings.
228 UNDERSTANDING YOUR INSTRUMENT PANEL language soft-key until a check-mark appears next to the • Touchscreen Beep language, showing that setting has been selected. Touch When in this display, you may turn on or shut off the the back arrow soft-key to return to the previous menu. sound heard when a touch screen button (soft-key) is • Units pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Fuel Saver Display In Cluster • Set Time Hours The “ECO” message is located in the instrument cluster display, this message can be turned on or off. To make your selection, touch the Fuel Saver Display soft-key, until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. When in this display, you may adjust the hours. The Sync with GPS Time soft-key must be unchecked.
230 UNDERSTANDING YOUR INSTRUMENT PANEL check-mark appears next to the 12hrs or 24hrs setting, • Tilt Mirrors In Reverse showing that setting has been selected. Touch the back When this feature is selected, the outside sideview mirarrow soft-key to return to the previous menu. rors will tilt downward when the ignition is in the RUN position and the transmission shift lever is in the RESafety / Assistance VERSE position.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 disappear. The ParkView威 camera is located on the rear of the vehicle above the rear License plate. To make your selection, touch the ParkView威 Backup Camera soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. the Hill Start Assist soft-key, until a check-mark appears next to setting, showing that setting has been selected.
232 UNDERSTANDING YOUR INSTRUMENT PANEL • Headlight Illumination On Approach When this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the Remote Keyless Entry (RKE) transmitter. To change the Illuminated Approach status, touch the + or - soft-key to select your desired time interval. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 • Flash Headlights With Lock opened. To make your selection, touch the Auto Unlock On Exit soft-key, until a check-mark appears next to When this feature is selected, the headlights will flash setting, showing that setting has been selected. Touch the when the doors are locked or unlocked with the Remote back arrow soft-key to return to the previous menu. Keyless Entry (RKE) transmitter.
234 UNDERSTANDING YOUR INSTRUMENT PANEL touch the Sound Horn With Lock soft-key, until a check- passenger’s doors. When Unlock All Doors On 1st Press mark appears next to setting, showing that setting has is selected, all of the doors will unlock on the first press been selected. Touch the back arrow soft-key to return to of the RKE transmitter UNLOCK button. the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 your selection, touch the Passive Entry soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. Refer to “Keyless Enter-NGo™” in “Things To Know Before Starting Your Vehicle”. • Memory To FOB — If Equipped This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
236 UNDERSTANDING YOUR INSTRUMENT PANEL Seats soft-key, until a check-mark appears next to setting, • Headlight Off Delay showing that setting has been selected. Touch the back When this feature is selected, the driver can choose to arrow soft-key to return to the previous menu. have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. • Perform Compass Calibration Touch the Calibration soft-key to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass.
238 UNDERSTANDING YOUR INSTRUMENT PANEL • Equalizer • Surround Sound When in this display you may adjust the Bass, Mid and Treble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key. This feature provides simulated surround sound mode. To make your selection, touch the Surround Sound soft-key, select On or Off followed by pressing the arrow back soft-key.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 • Channel Skip Write down the SIRIUS ID numbers for your receiver. To reactivate your service, either call the number listed on SiriusXM™ can be programmed to designate a group of the screen or visit the provider online. channels that are the most desirable to listen to or to exclude undesirable channels while scanning. To make NOTE: SiriusXM™ Travel Link is a separate subscripyour selection, touch the Channel Skip soft-key, select the tion.
240 UNDERSTANDING YOUR INSTRUMENT PANEL iPod威 control supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices. Some iPod威 software versions may not fully support the iPod威 control features. Please visit Apple’s website for software updates. For further information, refer to the Uconnect威 Access User’s Manual. STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 The button located in the center of the right hand control CD Player will switch modes to Radio, CD or other valid audio Pressing the top of the switch once will go to the next source. track on the CD. Pressing the bottom of the switch once The left hand control is a rocker type switch with a will go to the beginning of the current track or to the pushbutton in the center.
242 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Do not use solvents such as benzene, thinner, cleaners, not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the or anti-static sprays. antenna, it is recommended that the radio volume be 5. Store the disc in its case after playing. turned down or off during mobile phone operation when not using Uconnect威 (if equipped). 6. Do not expose the disc to direct sunlight. 7.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the OFF position.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Mode Control (Air Direction) Use this control to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. receive from that Mode control allows you to choose from several patterns of air distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Bi-Level Mode Mix Mode Air is directed through the panel and floor outlets. Air is directed through the floor, defrost and side window demist outlets. This setting works best in NOTE: There is a difference in temperature (in cold or snowy conditions that require extra heat at any conditions other than full cold or full hot), between the windshield. This setting is good for maintaining the upper and lower outlets for added comfort.
246 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because Press this button to choose between outside air of moisture buildup inside the vehicle. For maximum intake or recirculation of the air inside the defogging, select the outside air position. vehicle. A LED will illuminate when you are in Recirculation mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Rotate the temperature control knob to the desired tem- MAX A/C perature. Also, make sure to select only Panel, Bi-Level or For maximum cooling, when MAX A/C is selected the Floor modes. A/C is turned on automatically and the air is recirculated. Stop/Start System – If Equipped While in an Autostop, the Climate Controls system may NOTE: A/C cannot be deselected when in MAX A/C automatically adjust airflow to maintain cabin comfort. position.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Climate Controls With Touch-Screen — If Equipped Soft-Keys Soft-keys are accessible on the radio touch-screen. Hard-Keys The hard-keys located below the radio touch-screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Button Descriptions (Applies To Both Hard-keys And 3. Front Defrost Button Soft-keys) Press and release to change the current airflow setting 1. A/C Button to Defrost mode. The indicator illuminates when this Press and release to change the current setting, the feature is ON. Performing this function will cause the indicator illuminates when A/C is ON. Performing this ATC to switch into manual mode.
250 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 NOTE: BI-LEVEL mode is designed under comfort con- 6. Blower Control ditions to provide cooler air out of the panel outlets and Blower control is used to regulate the amount of air forced warmer air from the floor outlets. through the climate system. There are seven blower speeds • Floor Mode available. Adjusting the blower will cause automatic mode Air comes from the floor outlets. A slight amount to switch to manual operation.
252 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Climate Control OFF Button Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by 8. Temperature Control Down Button pressing the RECIRCULATION control button. Push the button for cooler temperature settings. On the Recirculation mode should only be used temporarily.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Automatic Climate Controls With Touch-Screen — If Equipped Soft-Keys Soft-keys are accessible on the radio touch-screen. Hard-Keys The hard-keys located below the radio touch-screen.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both Hard-keys And 3. Front Defrost Button Soft-keys) Press and release to change the current airflow setting to 1. A/C Button Defrost mode. The indicator illuminates when this feaPress and release to change the current setting, the ture is ON. Performing this function will cause the ATC indicator illuminates when A/C is ON. Performing this to switch into manual mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
256 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: BI-LEVEL mode is designed under comfort con- 6. Blower Control ditions to provide cooler air out of the panel outlets and Blower control is used to regulate the amount of air forced warmer air from the floor outlets. through the climate system. There are seven blower speeds • Floor Mode available. Adjusting the blower will cause automatic mode Air comes from the floor outlets. A slight amount to switch to manual operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 7. Climate Control OFF Button 10. AUTO Temperature Control Press and release this button to turn the Climate Control Controls airflow temperature, distribution, volume, and the amount of air recirculation automatically. Press and ON/OFF. release to select. Refer to “Automatic Operation” for 8. Driver Temperature Controls more information. Performing this function will cause Push the Up button for warmer temperature settings.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Next, adjust the temperature you would like the system to maintain by adjusting the driver and passenger temperature hard or soft control buttons. Once the desired temperature is displayed, the system will achieve and automatically maintain that comfort level. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 knob when this button is selected. Push the button a Winter Operation second time to turn off the Recirculation mode LED and To ensure the best possible heater and defroster perforallow outside air into the vehicle. mance, make sure the engine cooling system is functionNOTE: In cold weather, use of Recirculation mode may ing properly and the proper amount, type, and concenlead to excessive window fogging. The Recirculation tration of coolant is used.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging and Frosting Outside Air Intake Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather. Windows may frost on the inside of the glass in very cold weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .267 ▫ Brake/Transmission Shift Interlock System . . .273 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .267 ▫ Six–Speed Automatic Transmission (5.7L Engine) — If Equipped . . . . . . . . . . . . .273 ▫ Automatic Transmission . . . . . . . . . . . . . . . .268 ▫ Extreme Cold Weather (Below –20°F or −29°C) . . . . . . . . . . . . . . . . .268 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . .
264 STARTING AND OPERATING 䡵 䡵 䡵 䡵 䡵 ▫ Electronically Shifted Transfer Case 䡵 BRAKE SYSTEM . . . . . . . . . . . . . . . (Four-Position Switch) – If Equipped . . . . . . .288 ▫ Four-Wheel Anti-Lock Brake System ▫ Shifting Procedure . . . . . . . . . . . . . . . . . . . . .292 䡵 TIRE SAFETY INFORMATION . . . . . LIMITED-SLIP DIFFERENTIAL . . . . . . . . . . . . .294 ▫ Tire Markings . . . . . . . . . . . . . . . . DRIVING ON SLIPPERY SURFACES . . . . . . . . .295 ▫ Tire Identification Number (TIN). . .
STARTING AND OPERATING 265 ▫ Summer Or Three Season Tires – 䡵 If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .321 䡵 ▫ Spare Tire Matching Original Equipped Tire And Wheel – If Equipped. . . . . . . . . . . . . . . .321 䡵 ▫ Compact Spare Tire – If Equipped . . . . . . . . .322 ▫ Full Size Spare – If Equipped . . . . . . . . . . . . .323 ▫ Limited-Use Spare – If Equipped . . . . . . . . . .323 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .324 ▫ Tread Wear Indicators . . . . . .
266 STARTING AND OPERATING 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .338 ▫ Snowplow Prep Package Model Availability . . .357 ▫ Certification Label . . . . . . . . . . . . . . . . . . . .338 ▫ Over The Road Operation With Snowplow Attached. . . . . . . . . . . . . . . . . . . . . . . . . . . .358 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .341 ▫ Common Towing Definitions . . . . . . . . . . . . .341 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . .
STARTING AND OPERATING 267 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
268 STARTING AND OPERATING Automatic Transmission Extreme Cold Weather (Below –20°F or −29°C) Start the engine with the shift lever in the NEUTRAL or To ensure reliable starting at these temperatures, use of PARK position. Apply the brake before shifting into any an externally powered electric engine block heater (availdriving range. able from your authorized dealer) is recommended. NOTE: This vehicle is equipped with a transmission If Engine Fails To Start shift interlocking system.
STARTING AND OPERATING 269 WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
270 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. 3500 Models — 5.7L Engine Only The engine block heater cord is routed through the grille by the right front tow hook. It includes a removable cap that is secured by a tethered strap.
STARTING AND OPERATING 271 CAUTION! (Continued) WARNING! (Continued) • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. when the engine is idling normally and your foot is firmly pressing the brake pedal. • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running.
272 STARTING AND OPERATING WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
STARTING AND OPERATING 273 Brake/Transmission Shift Interlock System Six–Speed Automatic Transmission This vehicle is equipped with a Brake Transmission Shift (5.7L Engine) — If Equipped Interlock System (BTSI) that holds the transmission The shift lever position display (located in the instrument shifter in PARK unless the brakes are applied. To shift the cluster) indicates the transmission gear range.
274 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the NOTE: After selecting any gear range, wait a moment to accelerator pedal is released and the vehicle is stopped. allow the selected gear to engage before accelerating. Be sure to keep your foot on the brake pedal when This is especially important when the engine is cold. shifting between these gears.
STARTING AND OPERATING 275 WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever clockwise without first pulling it toward you after you have placed it in PARK.
276 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the key fob. When the ignition is in the OFF position, the shift lever is locked in PARK, securing the vehicle against unwanted movement.
STARTING AND OPERATING 277 CAUTION! • Before moving the shift lever out of PARK, you must turn the ignition switch from the OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • Look at the shift lever position display and verify that it indicates the PARK position.
278 STARTING AND OPERATING WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.
STARTING AND OPERATING 279 If the transmission temperature exceeds normal operating limits, the powertrain controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely hot or is in danger of overheating, the “Transmission Temperature Warning Light” may illuminate and the transmission may operate differently until the transmission cools down.
280 STARTING AND OPERATING selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without damaging the transmission. NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur.
STARTING AND OPERATING 281 shifting between all available gears. Tapping the ERS (-) To exit ERS mode, simply press and hold the ERS (+) switch will activate ERS mode, display the current gear in switch until “D” is once again displayed in the shift lever the instrument cluster, and maintain that gear as the top position indicator in the instrument cluster. available gear. Once in ERS mode, tapping ERS (-) or (+) will change the top available gear.
282 STARTING AND OPERATING HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due The automatic transmission includes an electronically to excessive shifting. When operating in TOW/HAUL controlled Overdrive (fifth and sixth gears).
STARTING AND OPERATING 283 The “TOW/HAUL Indicator Light” will illuminate in the NOTE: instrument cluster to indicate that TOW/HAUL mode • The torque converter clutch will not engage, and the has been activated. Pressing the switch a second time transmission will not shift to sixth gear, until the restores normal operation. Normal operation is always transmission fluid and engine coolant are warm [usuthe default at engine start-up. If TOW/HAUL mode is ally after 1 to 3 miles (2 to 5 km) of driving].
284 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED Four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further information. Manually Shifted Transfer Case – If Equipped The transfer case provides four mode positions.
STARTING AND OPERATING 285 the transfer case is shifted into either the 4H or 4L Because four-wheel drive provides improved traction, position. There is no light for the 2H or NEUTRAL there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. positions.
286 STARTING AND OPERATING For additional information on the appropriate use of each 4L transfer case mode position, see the information below: Four-Wheel Drive Low Range - This range locks the front and rear driveshafts together forcing the front and rear 2H wheels to rotate at the same speed. Additional traction Rear-Wheel Drive High Range - This range is for normal and maximum pulling power for loose, slippery road street and highway driving on dry hard surfaced roads. surfaces only.
STARTING AND OPERATING 287 vehicle in motion, the transfer case will engage/ • Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may occur due disengage faster if you momentarily release the accelerato the mating clutch teeth not being properly aligned. tor pedal after completing the shift. Apply a constant Several attempts may be required for clutch teeth force when shifting the transfer case lever. alignment and shift completion to occur.
288 STARTING AND OPERATING Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped This electronically shifted transfer case provides four mode positions: This is an electronic shift transfer case and is operated by • Two-wheel drive high range (2WD) the 4WD Control Switch (Transfer Case Switch), which is • Four-wheel drive lock range (4WD LOCK) located on the instrument panel.
STARTING AND OPERATING 289 desired position. Refer to “Shifting Procedure” in this section for specific shifting instructions. The 4WD LOCK and 4WD LOW positions are designed for loose, slippery road surfaces only. Driving in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components.
290 STARTING AND OPERATING If One Or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection.
STARTING AND OPERATING 291 Proper operation of four-wheel drive vehicles depends For additional information on the appropriate use of each on tires of equal size, type and circumference on each transfer case mode position, see the information below: wheel. Any difference in tire size can cause damage to the 2WD drivetrain. Rear Wheel Drive High Range - This range is for normal Because four-wheel drive provides improved traction, street and highway driving on dry, hard surfaced roads.
292 STARTING AND OPERATING • If all the requirements to select a new transfer case position have been met, the current position indicator Neutral - This range disengages both the front and rear light will turn OFF, the selected position indicator light driveshafts from the powertrain. To be used for flat towing will flash until the transfer case completes the shift. behind another vehicle.
STARTING AND OPERATING 293 NOTE: The four-wheel drive system will not allow shifts between 2WD/4WD LOCK if the front and/or rear wheels are spinning (no traction). In this situation, the selected position indicator light will flash and the original position indicator light will remain ON. At this time, reduce speed and stop spinning the wheels to complete the shift. Preferred Procedure 1. With the engine running, slow the vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL. 3.
294 STARTING AND OPERATING 3. Rotate the transfer case control switch to the desired LIMITED-SLIP DIFFERENTIAL position. The limited-slip differential provides additional traction 4. After the desired position indicator light is ON (not on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics flashing), shift the transmission back into gear. of the surface under the right and left rear wheels.
STARTING AND OPERATING 295 WARNING! On vehicles equipped with a limited-slip differential never run the engine with one rear wheel off the ground since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a road or in a turn.
296 STARTING AND OPERATING Traction DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. 1.
STARTING AND OPERATING 297 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
298 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 299 • Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system. WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
300 STARTING AND OPERATING The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, pull the parking brake release handle. When the parking brake is applied with the ignition switch ON, the “Brake Warning Light” in the instrument cluster will illuminate.
STARTING AND OPERATING 301 on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
302 STARTING AND OPERATING CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. will be evident by increased pedal travel during application, greater pedal force required to slow or stop, and activation of the “Brake Warning Light” and the “ABS Warning Light” (if equipped) during brake use.
STARTING AND OPERATING 303 Four-Wheel Anti-Lock Brake System WARNING! The Four-Wheel Anti-Lock Brake System contains sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure.
304 STARTING AND OPERATING ABS Warning Light WARNING! (Continued) The ABS includes an amber warning light. When the light is illuminated, the ABS is not functioning. The system reverts to standard, non-anti-lock brakes. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 305 TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
306 STARTING AND OPERATING compact spare tires have the letter “T” or “S” molded • High flotation tire sizing is based on U.S. design into the sidewall preceding the size designation. standards and it begins with the tire diameter molded Example: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING 307 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
308 STARTING AND OPERATING Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
STARTING AND OPERATING 309 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
310 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 311 Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading Tire and Loading Information Placard The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
312 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occuaxles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg” on your vehicle’s placard. “Vehicle Loading” in this section. 2.
STARTING AND OPERATING 313 5. Determine the combined weight of luggage and cargo NOTE: being loaded on the vehicle. That weight may not • The following table shows examples on how to calcusafely exceed the available cargo and luggage load late total load, cargo/luggage, and towing capacities capacity calculated in Step 4. of your vehicle with varying seating configurations 6. If your vehicle will be towing a trailer, load from your and number and size of occupants.
314 STARTING AND OPERATING
STARTING AND OPERATING 315 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
316 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar or rear edge of the driver’s side door.
STARTING AND OPERATING 317 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
318 STARTING AND OPERATING Tire Inflation Pressure – 4500/5500 With Steel Carcass Ply Tires Inflation Pressure Adjustment When Mounted To Vehicle This type of tire utilizes steel cords in the sidewall. As such, they cannot be treated like normal light truck tires. Adjusting tire pressure must be performed by personnel trained, supervised and equipped accordingly.
STARTING AND OPERATING 319 5 4500/5500 Tire Inflation
320 STARTING AND OPERATING When adjusting inflation pressure to a tire and wheel Tire Pressures For High Speed Operation assembly mounted on a vehicle, use a Remote Mount The manufacturer advocates driving at safe speeds Automatic Inflation Kit or see your authorized dealer. within posted speed limits.
STARTING AND OPERATING 321 Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Always use radial ply tires in sets of four (or six, in the case of trucks with dual rear wheels). Never combine them with other types of tires. the tire sidewall. Use all season tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle.
322 STARTING AND OPERATING rotation for your vehicle. If your vehicle has this option Compact Spare Tire – If Equipped refer to an authorized tire dealer for the recommended The compact spare is for temporary emergency use only. tire rotation pattern.
STARTING AND OPERATING 323 WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
324 STARTING AND OPERATING WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressure listed on your Tire and Loading Information Placard located on the driver’s side door opening. Replace (or repair) the original equipment tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 325 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven • Performance tires, tires with a speed rating of V or higher, and summer tires, typically have a reduced tread life. Rotation of these tires per the vehicle maintenance schedule is highly recommended. 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves.
326 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 327 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
328 STARTING AND OPERATING TIRE CHAINS CAUTION! (Continued) Use “Class U” chains or other traction aids that meet SAE Type “U” specifications. NOTE: Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used.
STARTING AND OPERATING 329 These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of your 4X2 trucks. NOTE: • The use of class “U” chains is permitted on the front and rear of 4X4 vehicles, trucks with dual rear wheels and LT235/80R17 tires.
330 STARTING AND OPERATING If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. TIRE ROTATION RECOMMENDATIONS While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.
STARTING AND OPERATING 331 Dual Rear Wheels 5 Tire Rotation NOTE: On Canadian vehicles only, if your vehicle is equipped with All-Season type tires on the front and On/Off Road type tires mounted on the rear, do not use a front to back rotation pattern. Instead, rotate your tires side to side at the recommended intervals. Tire Rotation The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set.
332 STARTING AND OPERATING CAUTION! 4500/5500 Dual Rear Tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/Off road tire. • When replacing a flat, the spare tire may have to be remounted on the rim or installed at a different location to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the vehicle.
STARTING AND OPERATING 333 Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline before considering service for the vehicle. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components.
334 STARTING AND OPERATING Problems that result from using gasoline containing To fix a Non-FFV vehicle inadvertently fueled once with Methanol or gasoline containing more than 10% Ethanol E-85 perform the following: are not the responsibility of the manufacturer and may • drain the fuel tank (see your authorized dealer) not be covered under warranty.
STARTING AND OPERATING 335 of gasoline may not be indicated on the gasoline pump, Fuel System Cautions therefore, you should ask your gasoline retailer whether or not his/her gasoline contains MMT. It is even more CAUTION! important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those Follow these guidelines to maintain your vehicle’s allowed in the United States. MMT is prohibited in performance: • The use of leaded gas is prohibited by Federal law.
336 STARTING AND OPERATING CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
STARTING AND OPERATING 337 WARNING! (Continued) CAUTION! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • A poorly fitting gas cap may cause the MIL to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
338 STARTING AND OPERATING NOTE: Tighten the gas cap 1/4 turn until you hear one Refer to “Electronic Vehicle Information Center (EVIC) in click. This is an indication that the cap is properly “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press tightened. the SELECT button to turn off the message.
STARTING AND OPERATING 339 included on this label and indicates the Month, Day and Each axle GAWR is determined by the components in the Hour of manufacture. The bar code that appears on the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension bottom of the label is your VIN.
340 STARTING AND OPERATING within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the The curb weight of a vehicle is defined as the total weight specified weight limitations are met. Store the heavier of the vehicle with all fluids, including vehicle fuel, at full items down low and be sure that the weight is distributed capacity conditions, and with no occupants or cargo loaded equally. Stow all loose items securely before driving.
STARTING AND OPERATING 341 exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for In this section you will find safety tips and information further information. on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully Gross Trailer Weight (GTW) review this information to tow your load as efficiently The GTW is the weight of the trailer plus the weight of all and safely as possible.
342 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Tongue Weight (TW) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information. The tongue weight is the downward force exerted on the hitch ball by the trailer.
STARTING AND OPERATING 343 Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier Tongue A weight-carrying hitch supports the trailer tongue Weights (TW) and may be required depending on vehicle weight, just as if it were luggage located at a hitch ball or and trailer configuration/loading to comply with GAWR some other connecting point of the truck. These kind of requirements.
344 STARTING AND OPERATING Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed.
STARTING AND OPERATING 345 Trailer Towing Weights (Maximum Trailer Weight Ratings) NOTE: Refer to the following website address for your specific vehicle’s “BASE WEIGHTS/GCW/PAYLOAD/ TRAILER TOW” information and restrictions based on the type of trailer hitch: • http://www.dodge.com/bodybuilder Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle.
346 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for further information.
STARTING AND OPERATING 347 WARNING! (Continued) WARNING! (Continued) control. You could lose control of your vehicle and have a collision. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • Safety chains must always be used between your vehicle and trailer.
348 STARTING AND OPERATING Towing Requirements – Tires • Do not attempt to tow a trailer while using a compact spare tire. replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. • Proper tire inflation pressures are essential to the safe Towing Requirements – Trailer Brakes and satisfactory operation of your vehicle.
STARTING AND OPERATING 349 CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
350 STARTING AND OPERATING NOTE: This module has been designed and verified The user interface consists of the following: with electric trailer brakes and new electric over hydrauManual Brake Control Lever lic systems. Some previous EOH systems may not be compatible with ITBM. Slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes.
STARTING AND OPERATING 351 sliding the manual brake control lever will display the Adjusting GAIN GAIN setting for 10 seconds and the “Trailer Brake Status NOTE: This should only be performed in a traffic free Indicator Light” will not be displayed. environment at speeds of approximately 20–25 mph If a fault is detected in the trailer wiring or the Integrated (30–40 km/h). Trailer Brake Module (ITBM), the “Trailer Brake Status 1. Make sure the trailer brakes are in good working Indicator Light” will flash.
352 STARTING AND OPERATING 4. Press the UP or DOWN button on the steering wheel 9. If the trailer wheels lockup (indicated by squealing until “VEHICLE SETTINGS” appears on the screen. tires), reduce the GAIN setting; if the trailer wheels turn freely, increase the GAIN setting. 5. Press the RIGHT arrow on the steering wheel to enter “VEHICLE SETTINGS”. Repeat Steps 8 and 9 until the GAIN setting is at a point just below trailer wheel lockup. If towing a heavier 6.
STARTING AND OPERATING 353 * The suggested selection depends and may change depending on the customer preferences for braking performance. Condition of the trailer brakes, driving and road state may also affect the selection. EVIC Display Messages The trailer brake control interacts with the Electronic Vehicle Information Center (EVIC). Display messages, along with a single chime, will be displayed when a malfunction is determined in the trailer connection, trailer brake control, or on the trailer.
354 STARTING AND OPERATING NOTE: • An aftermarket controller may be available for use with trailers with air or electric-over-hydraulic trailer brake systems. To determine the type of brakes on your trailer and the availability of controllers, check with your trailer manufacturer or dealer. WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automotive technician.
STARTING AND OPERATING 355 TOW/HAUL mode or select a lower gear range (using NOTE: Check the automatic transmission fluid level the Electronic Range Select (ERS) shift control). before towing. NOTE: Using TOW/HAUL mode, or selecting a lower gear range (using the ERS shift control) while operating the vehicle under heavy loading conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
356 STARTING AND OPERATING NOTE: Before installation of a snowplow it is highly recommended that the owner/installer obtain and follow To reduce potential for engine and transmission overthe recommendations contained within the current Ram heating, take the following actions: Body Builders Guide. See your authorized dealer, inCity Driving staller or snowplow manufacturer for this information.
STARTING AND OPERATING 357 CAUTION! The “Lamp Out” indicator could illuminate if exterior lamps are not properly installed. Before Plowing Snowplow Prep Package Model Availability For Information about snowplow applications visit www.dodge.com or refer to the current Dodge Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two. • Check the hydraulic system for leaks and proper fluid 2. The total GVWR or the Front GAWR or the Rear level. GAWR should never be exceeded.
358 STARTING AND OPERATING NOTE: Detach the snowplow when transporting pas- completely and position it as low as road or surface conditions permit. Do not exceed 40 mph (64 km/h). The sengers. operator should always maintain a safe stopping distance Vehicle front end wheel alignment was set to specificaand allow adequate passing clearance. tions at the factory without consideration for the weight of the plow.
STARTING AND OPERATING 359 When plowing snow, to avoid transmission and drive- • Vehicles with automatic transmissions should use 4L train damage, the following precautions should be obrange when plowing deep or heavy snow for extended served. periods of time to avoid transmission overheating. • Operate with transfer case in 4L when plowing small • Do not shift the transmission unless the engine has or congested areas where speeds are not likely to returned to idle and wheels have stopped.
360 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 361 Recreational Towing – Two-Wheel Drive Models 5. Remove the key fob from the ignition switch. DO NOT flat tow this vehicle. Damage to the drivetrain 6. Install a suitable clamping device, designed for towwill result. ing, to secure the front wheels in the straight position. Recreational towing (for two-wheel drive models) is allowed ONLY if the rear wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer.
362 STARTING AND OPERATING Recreational Towing – Four-Wheel Drive Models NOTE: Both the manual shift and electronic shift transfer cases must be shifted into NEUTRAL (N) for recreational towing. Automatic transmissions must be shifted into PARK for recreational towing. Manual transmissions must be placed in gear (NOT in NEUTRAL) for recreational towing. Refer to the following for the proper transfer case NEUTRAL (N) shifting procedure for your vehicle.
STARTING AND OPERATING 363 CAUTION! (Continued) WARNING! (Continued) • Do not disconnect the rear driveshaft because fluid will leak from the transfer case, causing damage to internal parts. • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, even if the transmission is in PARK.
364 STARTING AND OPERATING 3. Press and hold the brake pedal. 4. Depress the clutch pedal on a manual transmission. 5. If the transfer case is in 4WD AUTO (if equipped), press a selector button or rotate the selector switch to shift the transfer case into the 2WD or 4WD LOCK position. • With manual shift transfer case, shift the transfer case lever into NEUTRAL (N). • With electronic shift transfer case, press and hold the transfer case NEUTRAL (N) button.
STARTING AND OPERATING 365 • The ignition switch must be in the ON/RUN position for a shift to take place and for the position indicator 13. Attach the vehicle to the tow vehicle using a suitable lights to be operable. If the ignition switch is not in the tow bar. ON/RUN position, the shift will not take place and no position indicator lights will be on or flashing. 14. Release the parking brake. 12. Remove the key fob from the ignition switch.
366 STARTING AND OPERATING 5. Shift the transmission into NEUTRAL • With manual shift transfer case, shift the transfer case lever to the desired position. • With electronic shift transfer case, press and hold the transfer case NEUTRAL (N) button until the NEUTRAL (N) indicator light turns off. After the NEUTRAL (N) indicator light turns off, release the NEUTRAL (N) button. After the NEUTRAL (N) button has been released, the transfer case will shift to the position indicated by the selector switch.
STARTING AND OPERATING 367 • The ignition switch must be in the ON/RUN position for a shift to take place and for the position indicator • Steps 3 through 5 are requirements that must be met lights to be operable. If the ignition switch is not in the prior to pressing the NEUTRAL (N) button, and must ON/RUN position, the shift will not take place and no continue to be met until the shift has been completed. position indicator lights will be on or flashing.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .370 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . .383 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .370 䡵 FREEING A STUCK VEHICLE . . . . . . . . . . . . .385 ▫ 4500/5500 Models . . . . . . . . . . . . . . . . . . . . .371 䡵 EMERGENCY TOW HOOKS — IF EQUIPPED . . . . . . . . . . . . . . ▫ Preparations For Jacking. . . . . . . . . . . . . . . . .371 䡵 SHIFT LEVER OVERRIDE . . . . . ▫ Jacking Instructions . . . . .
370 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS The Hazard Warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flashers. This is an emergency warning system and it should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 371 WARNING! (Continued) • The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. 4500/5500 Models These vehicles do not come equipped with a jack. Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.
372 WHAT TO DO IN EMERGENCIES 5. Turn OFF the ignition. Jacking Instructions Instructions Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 373 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
374 WHAT TO DO IN EMERGENCIES 3. When changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
WHAT TO DO IN EMERGENCIES 375 Before raising the wheel off the ground, make sure that 5. Remove the wheel nuts and pull the wheel off. Install the spare wheel and wheel nuts with the cone shaped the jack will not damage surrounding truck parts and end of the nuts toward the wheel on single rear wheel adjust the jack position as required. (SRW) models. On dual rear wheel models (DRW) the NOTE: If the jack will not lower by turning the dial lug nuts are a two-piece assembly with a flat face.
376 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. 7. Install wheel center cap (if equipped) and remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel. This may result in cap damage. NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts.
WHAT TO DO IN EMERGENCIES 377 On 3500 models with dual rear wheels (DRW), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pry off notch of the rear hub caps. Position the hook and pull out on the ratchet firmly. The hub cap should pop off. The wheel skins can now be removed. For the front hub cap on models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be removed.
378 WHAT TO DO IN EMERGENCIES Dual Rear Wheels Dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer. Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assembling the wheels for best access to the tire valve on the inner wheel.
WHAT TO DO IN EMERGENCIES 379 These dual rear wheels should be tightened as follows: Tightening Pattern (10 Studs) Tightening Pattern (8 Studs) 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km).
380 WHAT TO DO IN EMERGENCIES It is recommended that wheel stud nuts be kept torqued kilometers of operation to allow the wheel nuts to become to specifications at all times. Torque wheel stud nuts to properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recomspecifications at each lubrication interval. mended torque. Tighten the nuts to final torque in increWheel Nut Torque ments.
WHAT TO DO IN EMERGENCIES 381 To Stow The Flat Or Spare — If Equipped JUMP-STARTING PROCEDURES Refer to Upfitters Body Builders Guide for information If your vehicle has a discharged battery it can be jumpon stowing your spare tire (if equipped). started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster HOISTING pack.
382 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post.
WHAT TO DO IN EMERGENCIES 383 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
384 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
WHAT TO DO IN EMERGENCIES 385 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand, or snow, it 9. Disconnect the positive (+)end of the jumper cable can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the from the positive (+) post of the discharged vehicle. front wheels.
386 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rockingmotion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle.
WHAT TO DO IN EMERGENCIES 387 WARNING! WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. • Do not use a chain for freeing a stuck vehicle.
388 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: 1. Turn the engine OFF. 2. Firmly apply the parking brake. 3. Tilt the steering wheel to the full up position. 4. Press and maintain firm pressure on the brake pedal. 5.
WHAT TO DO IN EMERGENCIES 389 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the transmission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational Towing” in the “Starting and Operating” section.
390 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent CAUTION! damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- Do not use sling type equipment when towing. ment manufacturer’s instructions. Use of safety chains is When securing the vehicle to a flat bed truck, do not mandatory. Attach a tow bar or other towing device to attach to front or rear suspension components.
WHAT TO DO IN EMERGENCIES 391 If flatbed equipment is not available, and the transmis- wheels on a towing dolly, or (when using a suitable sion is operable, the vehicle may be towed under the steering wheel stabilizer to hold the front wheels in the straight position) with the rear wheels raised and the following conditions: front wheels on the ground. NOTE: With rear wheels off the ground. • The transmission must be in NEUTRAL. • The towing speed must not exceed 30 mph (48 km/h).
392 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Models The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 5.7L . . . . . . . . . .395 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .403 䡵 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . .396 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .403 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .396 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .405 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . .
394 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .417 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . . .441 ▫ Rear Axle And 4x4 Front Driving Axle Fluid Level . . . . . . . . . . . . . . . .419 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . .421 ▫ Automatic Transmission – If Equipped . . . . . .421 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . .424 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 395 ENGINE COMPARTMENT — 5.
396 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 397 “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
398 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
MAINTAINING YOUR VEHICLE 399 available which include detailed service information for MAINTENANCE PROCEDURES your vehicle. Refer to these Service Manuals before The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle.
400 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 401 Change Engine Oil American Petroleum Institute (API) Engine Oil The oil change indicator system will remind you that it is Identification Symbol time to take your vehicle in for scheduled maintenance. This symbol means that the oil has Refer to the “Maintenance Schedule” for further informabeen certified by the American tion. Petroleum Institute (API).
402 MAINTAINING YOUR VEHICLE Engine Oil Viscosity Disposing Of Used Engine Oil And Oil Filters SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 403 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” for the proper The quality of replacement engine air cleaner filters maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine air cleaner filters are a high quality filter and are recomWARNING! mended. The air induction system (air cleaner, hoses, etc.
404 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. • Battery gas is flammable and explosive.
MAINTAINING YOUR VEHICLE 405 Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
406 MAINTAINING YOUR VEHICLE Front Prop Shaft Lubrication – Four-Wheel Drive Models underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. Lubricate the front driveshaft grease fitting at each oil change. Refer to the “Maintenance Schedule” for the proper maintenance intervals. Use MOPAR威 Type MS-6560 (lithium-based grease), or equivalent. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
MAINTAINING YOUR VEHICLE 407 Avoid using the wiper blades to remove frost or ice from To prevent freeze-up of your windshield washer system the windshield. Keep the blade rubber out of contact with in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This petroleum products such as engine oil, gasoline, etc. rating information can be found on most washer fluid NOTE: Life expectancy of wiper blades varies dependcontainers.
408 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE 409 CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
410 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- Cooling System age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
MAINTAINING YOUR VEHICLE 411 spraying water from a garden hose vertically down the Cooling System – Drain, Flush, And Refill face of the A/C condenser (if equipped) or the back of the If the engine coolant (antifreeze) is dirty or contains a radiator core. considerable amount of sediment, clean and flush with a Check the engine cooling system hoses for brittle rubber, reliable cooling system cleaner.
412 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).
MAINTAINING YOUR VEHICLE 413 period, it is important that you use the same engine Please note that it is the owner’s responsibility to maincoolant (antifreeze) throughout the life of your vehicle. tain the proper level of protection against freezing according to the temperatures occurring in the area where Please review these recommendations for using Organic the vehicle is operated. Additive Technology (OAT) engine coolant (antifreeze).
414 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 415 To check the coolant level: 1. Open the coolant reservoir. 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there 2. Lift and remove the plastic dipstick from the reservoir is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing neck.
416 MAINTAINING YOUR VEHICLE engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant expansion bottle.
MAINTAINING YOUR VEHICLE 417 • Make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
418 MAINTAINING YOUR VEHICLE The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot. The fluid level must be kept within these two dots. Do not add fluid above the MAX mark because leakage may occur at the cap. With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted.
MAINTAINING YOUR VEHICLE 419 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
420 MAINTAINING YOUR VEHICLE Refer to the “Maintenance Schedule” for the proper On 4500/5500 vehicles, remove the lower bolt to drain maintenance intervals. the axle fluid. Lubricant Selection Drain And Refill Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components.
MAINTAINING YOUR VEHICLE 421 only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in Drain And Refill “Maintaining Your Vehicle” for fluid specifications. It is Refer to the “Maintenance Schedule” for the proper important to maintain the transmission fluid at the maintenance intervals. correct level using the recommended fluid. No chemical flushes should be used in any transmission; only the Lubricant Selection approved lubricant should be used.
422 MAINTAINING YOUR VEHICLE Special Additives Fluid Level Check – 5.7L Engine The manufacturer strongly recommends against using any special additives in the transmission. Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid additives to the transmission. The only exception to this policy is the use of special dyes for diagnosing fluid leaks.
MAINTAINING YOUR VEHICLE 423 3. Run the engine at normal idle speed for at least 60 seconds, and leave the engine running for the rest of this procedure. 4. Fully apply the parking brake and press the brake 5. Place the shift lever momentarily into each gear position (allowing time for the transmission to fully engage in each position), ending with the lever in PARK. to bring it to the proper level. Do not overfill.
424 MAINTAINING YOUR VEHICLE CAUTION! If the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. Run the engine at idle, in PARK, to warm the fluid. 8. Check for leaks. Release the parking brake. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated.
MAINTAINING YOUR VEHICLE 425 • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug Corrosion is the result of deterioration or removal of and Tar Remover to remove. paint and protective coatings from your vehicle. • Use a high quality cleaner wax, such as MOPAR威 The most common causes are: Cleaner Wax to remove road film, stains and to protect • Road salt, dirt and moisture accumulation. your paint finish. Take care never to scratch the paint.
426 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well • If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once a month. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE 427 CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s protective finish. Only MOPAR威 Wheel Cleaner or equivalent is recommended.
428 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 429 Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric.
430 MAINTAINING YOUR VEHICLE fuse is stamped on the inside cover that corresponds to the following chart.
MAINTAINING YOUR VEHICLE 431 Cavity F12 F13 F14 F15 F19 F20 Cartridge Fuse 40 Amp Green 40 Amp Green 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink Micro Fuse Description Cavity Body Controller #3/ Interior Lights Blower Motor F21 Body Controller #4/ Power Locks Electric Park Brake Right Side – If Equipped SCR – If Equipped F23 F22 F24 F25 F25 Passenger Door Module Cartridge Fuse 30 Amp Pink 20 Amp Yellow 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink Micro Fuse Description Drive Train
432 MAINTAINING YOUR VEHICLE Cavity F26 Cartridge Fuse 30 Amp Pink F28 20 Amp Yellow F29 20 Amp Yellow F30 F32 30 Amp Pink 30 Amp Pink Micro Fuse Description Cavity Antilock Brakes/ Stability Control Module/Valves Trailer Tow Backup Lights – If Equipped Trailer Tow Parking Lights – If Equipped Trailer Tow Receptacle Drive Train Control Module – If Equipped F33 Cartridge Fuse 20 Amp Yellow F34 30 Amp Pink F35 30 Amp Pink 30 Amp Pink 30 Amp Pink F36 F37 Micro Fuse Description Diesel Fue
MAINTAINING YOUR VEHICLE 433 Cavity F38 F39 F41 F42 F43 F44 Cartridge Fuse 30 Amp Pink 30 Amp Pink Micro Fuse 10 Amp Red 20 Amp Yellow 10 Amp Red 10 Amp Red Description Cavity Power Inverter 115V AC– If Equipped Vehicle System Interface Module #1– If Equipped Active Grill Shutter F46 F47 F49 F50 Cartridge Fuse Micro Fuse Description 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow Tire Pressure Monitor Snow Plow (Right) – If Equipped Instrument Panel Cluster Air Suspension Control Module – If E
434 MAINTAINING YOUR VEHICLE Cavity F53 F54 F55 F56 F57 Cartridge Fuse Micro Fuse Description Cavity 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Blue Trailer Tow – Left Turn/Stop Lights Adjustable Pedals F58 20 Amp Yellow E38 Radio – If Equipped Additional Diesel Content – If Equipped Transmission F60 F61 Cartridge Fuse Micro Fuse Description 20 Amp Yellow (Gas Engine)/ 25 Amp Natural (Diesel Engine) 15 Amp Blue 20 Amp Yellow Engine Cooling Pump Underhood Lamp Power Take-off Unit – I
MAINTAINING YOUR VEHICLE 435 Cavity F62 F63 F64 F65 F66 Cartridge Fuse Micro Fuse Description Cavity 10 Amp Red 20 Amp Yellow 25 Amp Natural 10 Amp Red 10 Amp Red Air Conditioning Clutch Ignition Coils (Gas), Urea Heater (Diesel) Fuel Injectors/ Powertrain USB interface Sunroof/Passenger Window Switches/ Rain Sensor Micro Fuse Description F67 10 Amp Red F69 15 Amp Blue 30 Amp Green 25 Amp Natural 10 Amp Red CD/DVD/ Bluetooth Hands-free Module – If Equipped Mod SCR 12V – If Equipped Fuel Pump
436 MAINTAINING YOUR VEHICLE Cavity F74 F75 F76 Cartridge Fuse Micro Fuse Description Cavity 20 Amp Yellow (Gas Engine)/ 10 Amp Red (Diesel Engine) 10 Amp Red 10 Amp Red Brake Vacuum Pump Gas/Diesel – If Equipped Coolant Temperature Valve Actuator Antilock Brakes/ Electronic Stability Control Micro Fuse Description F77 10 Amp Red F78 10 Amp Red F79 15 Amp Blue 10 Amp Red Drivetrain Control Module/Front Axle Disconnect Module Engine Control Module/Electric Power Steering Clearance Lights
MAINTAINING YOUR VEHICLE 437 Cavity Micro Fuse Description Cavity F82 10 Amp Red F88 F84 15 Amp Blue 10 Amp Red 10 Amp Red 10 Amp Red Steering Column Control Module/ Cruise Control Switch Bank/ Instrument Cluster Airbag Module F90/ F91 Airbag Module F94 Air Suspension/ Trailer Tow/Steering Column Control Module F95 F85 F86 F87 Cartridge Fuse F93 F96 Cartridge Fuse Micro Fuse Description 15 Amp Blue 20 Amp Yellow Instrument Panel Cluster Power Outlet (Rear seats) Customer Selectable C
438 MAINTAINING YOUR VEHICLE Cavity Micro Fuse Description F97 25 Amp Natural F98 25 Amp Natural 10 Amp Red 15 Amp Blue Rear Heated Seats & Heated Steering Wheel – If Equipped Front Heated Seats – If Equipped Climate Control F99 F101 F104 Cartridge Fuse 20 Amp Yellow Electrochromatic Mirror/Smart High Beams – If Equipped Power Outlets (Instrument Panel/ Center Console) CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and
MAINTAINING YOUR VEHICLE 439 VEHICLE STORAGE NOTE: If you are storing your vehicle for more than 21 days, we • When reinstalling the IOD fuse push firmly until fully recommend that you take the following steps to miniseated; the gauges in the instrument cluster will do a mize the drain on your vehicle’s battery: full sweep when the ignition switch is turned to the RUN position. This is a normal condition.
440 MAINTAINING YOUR VEHICLE LIGHT BULBS — Interior Bulb Number TS 212-2 Overhead Console Lamps Dome Lamp 7679 For lighted switches, see your authorized dealer for replacement instructions.
MAINTAINING YOUR VEHICLE 441 BULB REPLACEMENT Base Quad / Premium Bi-Halogen: Low Beam Headlamp, High Beam Headlamp, Front Park And Turn – If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two plastic push-in rivets that secure the 7. Reach into the front wheel house ahead of the front upper radiator seal to the radiator.
442 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect the wiring harness connectors from the splash shield and lift the slide lock upward far enough bulb socket. to disengage it from the lock post on the back of the 11. Replace bulb(s) as necessary. front lamp unit housing. CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE 443 Fog Lamps – If Equipped Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 1. Reach under and behind the front bumper to access 1. Remove the two screws holding the housing/lens to the back of the front fog lamp housing. the body as shown. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise ¼ turn to unlock the bulb from the housing. 4. Pull the bulb straight out from the housing.
444 MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wir- 3. Turn the desired bulb socket ¼ turn and remove the ing harness to the body. socket and bulb from housing. 4. Pull the desired bulb straight from the socket.
MAINTAINING YOUR VEHICLE 445 CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. Cab Top Clearance Lamps – If Equipped 1. Remove the two screws from the top of the lamp. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing.
446 MAINTAINING YOUR VEHICLE 2. Rotate the socket ¼ turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
MAINTAINING YOUR VEHICLE 447 FLUID CAPACITIES Fuel (Approximate) Standard Rear Tank Optional Midship Tank Engine Oil With Filter 5.7L Engine (SAE 5W-20, API Certified) Cooling System 5.7L Engine (MOPAR威 Antifreeze/Coolant 10 Year/150,000 Mile Formula). U.S. Metric 52 Gallons 22 Gallons 197 Liters 83 Liters 7 Quarts 6.6 Liters 18.7 Quarts 17.
448 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 5.7L Engine Engine Oil Filter – 5.7L Engine Spark Plugs – 5.7L Engine Fuel Selection – 5.7L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR威 Antifreeze/Coolant 10-Year/150,000 Mile Formula OAT (Organic Additive Technology). We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 449 Chassis Component Automatic Transmission (5.7L Engine Only) Transfer Case Front and Rear Axle Fluid (4500/5500) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part We recommend you use MOPAR威 ATF+4威 Automatic Transmission Fluid. Failure to use ATF+4 fluid may affect the function or performance of your transmission. We recommend you use MOPAR威 ATF+4威 Automatic Transmission Fluid. We recommend you use GL-5 SAE 75W-90 Synthetic (MS-9763) .
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . . .452 ▫ Maintenance Chart. . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 452 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle.
MAINTENANCE SCHEDULES 453 M • Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic transmission as needed • Check function of all interior and exterior lights • Required Maintenance • Refer to the Maintenance Schedules on the following pages for required maintenance. • At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires.
8 Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle surfaces. If gear oil leakage is suspected, check the fluid level. If using your vehicle for police, taxi, fleet, off-road or frequent trailer towing, change axle fluid.
Inspect the brake linings, parking brake function. Inspect transfer case fluid. Additional Maintenance Replace engine air filter. Replace spark plugs (5.7L engine).** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change automatic transmission fluid and filter(s), if using your vehicle for police, taxi, fleet, or frequent trailer towing.
S C H E D U L E S 8 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 2 3 4 5 6 7 8 9 10 11 12 13 14 15 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 M 456 MAINTENANCE SCHEDULES A I Mileage or time passed N (whichever comes first) T E N Or Years: A Or Kilometers: N C E Change automatic transmission fluid and filter.
MAINTENANCE SCHEDULES 457 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . .461 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .463 ▫ Prepare For The Appointment. . . . . . . . . . . . .461 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .463 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .461 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .463 ▫ Be Reasonable With Requests . .
460 IF YOU NEED CONSUMER ASSISTANCE 䡵 PUBLICATION ORDER FORMS . . . . . . . . . . . .466 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .468 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . .467 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .468 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 461 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
462 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 463 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1 800 855-0511 to connect with a Bell Relay Service operator.
464 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 465 MOPAR姞 PARTS individual problems between you, your authorized dealer, and the manufacturer. MOPAR威 fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- To contact NHTSA, you may either call the Auto Safety mended for your vehicle in order to help keep the vehicle Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– operating at its best. 9153), or go to http://www.safercar.
466 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 467 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
468 IF YOU NEED CONSUMER ASSISTANCE Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
INDEX 10
470 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .412 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .337 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .160 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .71 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 471 .273 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . .441 .422 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 .419 .419 Cab Top Clearance Lights . . . . . . . . . . . . . . . . . . .445 Capacities, Antifreeze (Engine Coolant) . . . . . . . . . .447 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .403 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .447 Keyless Transmitter Replacement (RKE) . . . . . . . .
472 INDEX Checking Your Vehicle For Safety . . . . . . . . . . . . . .111 Checks, Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Cigar Lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .426 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . .242 Cold Weather Operation . . . . . . . . . . . . . . . . . . . .
INDEX 473 Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . .387 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . .414 Emission Control System Maintenance . . . . . . . . . .397 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .403 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . . .
474 INDEX Exhaust System. . . . . . . . . . . . . . . . . . . . . . . . . . .112 Fluids, Lubricants and Genuine Parts Exterior Lighting. . . . . . . . . . . . . . . . . . . . . . . . . .145 Fog Lights . . . . . . . . . . . . . . . . . . . Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .115 Four-Way Hazard Flasher . . . . . . . . Four Wheel Drive . . . . . . . . . . . . . . Freeing A Stuck Vehicle . . . . . . . . . . Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 475 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . . .333 Gauges Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . .194 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . .189 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 Gear Select Lever Override . . . . . . . . . . . . . . . . . .388 General Information . . . . . . . . . . . . . . . . . . . . . . . .21 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .
476 INDEX Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . . .16 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . . .23 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . .19 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . .327 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . .121 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 477 Anti-Lock . . . . . . . . . . . . . . . . . . . Anti-Lock Warning . . . . . . . . . . . . . Automatic Headlights . . . . . . . . . . Brake Warning . . . . . . . . . . . . . . . . Bulb Replacement . . . . . . . . . . . . . Cap Top Clearance . . . . . . . . . . . . . Cargo . . . . . . . . . . . . . . . . . . . . . . Center Mounted Stop . . . . . . . . . . . Check Engine (Malfunction Indicator) Courtesy/Reading . . . . . . . . . . . . . Daytime Running . . . . . . . . . . . . . Exterior . . . . . .
478 INDEX Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Child Protection . . . . . . . . . . . . . . . . . . . . . . . .36 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . .128 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 479 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . .402 Identification Logo . . . . . . . . . . . . . . . . . . . . . .401 Recommendation . . . . . . . . . . . . . . . . . . . . . . .401 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .402 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .402 Onboard Diagnostic System . . . . . . . . . . . . . . . . . .396 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .
480 INDEX Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . .321 Radiator Cap (Coolant Pressure Cap) . . . . . . . . . . .411 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . .242 Rain Sensitive Wiper System . . . . . . . . . . . . . . . . .158 Rear Axle (Differential) . . . . . . . . . . . . . . . . . . . . .419 Rear Window Features . . . . . . . . . . . . . . . . . . . . .182 Rear Window, Sliding . . . . . . . . . . . . . . . . . . . . . .183 Reclining Rear Seats . . . .
INDEX 481 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Adjustable Upper Shoulder Anchorage . . . . . . . .56 And Pregnant Women . . . . . . . . . . . . . . . . . . . .61 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . .75 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Reminder . . . . . . . . . .
482 INDEX Snow Plow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .356 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329 Spare Tire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 Speed Control (Cruise Control). . . . . . . . . . . . . . . .163 Speedometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 483 High Speed . . . . . . . . . . . Inflation Pressures . . . . . . Life of Tires . . . . . . . . . . . Load Capacity . . . . . . . . . Pressure Warning Light . . Quality Grading . . . . . . . Radial . . . . . . . . . . . . . . . Replacement . . . . . . . . . . Rotation . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . Sizes . . . . . . . . . . . . . . . . Snow Tires . . . . . . . . . . . Spinning . . . . . . . . . . . . . Tread Wear Indicators . . . Wheel Nut Torque . . . . . .
484 INDEX Transmission Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .273 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .449 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .421 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 Transmitter Battery Service (Remote Keyless Entry) . .28 Transmitter Programming (Remote Keyless Entry) . . .23 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . .23 Tread Wear Indicators . . . . . . . .
INDEX 485 Windshield Defroster. . . . Windshield Washers . . . . Fluid . . . . . . . . . . . . Windshield Wiper Blades . Windshield Wipers . . . . . Wiper Blade Replacement Wipers, Intermittent . . . . Wipers, Rain Sensitive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
486 INDEX
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
Chrysler Group LLC 13DD43-126-AC 300 3rd Edition Printed in U.S.A.
