OWNER’S MANUAL Chrysler Group LLC 13MZZ-126-AB Second Edition RAM CV C a r g o Va n Printed in U.S.A. 1207472cv1 13MZZ-126-AB Chrysler 1" gutter 06/13/2012 17:12:08 2013 RAM CARGO VAN 2013 OWNER’S MANUAL Chrysler Group LLC 13MZZ-126-AB Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VAN CONVERSIONS/CAMPERS . . . . . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .6 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS VAN CONVERSIONS/CAMPERS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ To Arm The System . . . . . . . . . . . . . . . ▫ Removing Key Fob From Ignition . . . . . . . . . .14 ▫ To Disarm The System . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 REMOTE KEYLESS ENTRY (RKE) — 䡵 SLIDING SIDE DOOR . . . . . . . . . . . . . . . . . . IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ Power Sliding Side Door — If Equipped . . . . ▫ Using The RKE Transmitter . . . . . . . . . . . . . . .21 ▫ Sliding Side Door Child Protection Lock . . . . 䡵 REMOTE STARTING SYSTEM — 䡵 LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Supplemental Active Head Restraints (AHR) . . .68 䡵 COMMERCIAL CARGO VEHICLES (NO FACTORY INSTALLED REAR SEATS) — IF ▫ Enhanced Seat Belt Use Reminder System EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . . . . (BeltAlert®) . . . . . . . . . . . . . . . . . . . . . . . . . .73 ▫ Restraining Infants And Small Children In ▫ Seat Belts And Pregnant Women . . . . . . . . . . .74 Commercial Cargo Vehicles. . . . . . . . . . . . . ▫ Seat Belt Extender . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similarly to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition WARNING! (Continued) Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob. NOTE: Power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening the front door will cancel this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from the ignition and lock all doors when leaving the vehicle unattended. Key-In-Ignition Reminder SENTRY KEY® The Sentry Key® Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the bulb check, it indicates that someone used an invalid Replacement Keys Key Fob to start the engine. Either of these conditions will NOTE: Only Key Fobs that are programmed to the result in the engine being shut off after two seconds. vehicle electronics can be used to start and operate the If the Vehicle Security Light turns on during normal vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key® Immobilizer sys- VEHICLE SECURITY ALARM — IF EQUIPPED tem serviced, bring all vehicle Key Fobs with you to the The Vehicle Security Alarm monitors the vehicle doors authorized dealer. for unauthorized entry and the ignition switch for unauthorized operation.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rearming Of The System The Vehicle Security Alarm will rearm itself after the 15 additional minutes of headlights and Vehicle Security Light flashing, if the Vehicle Security Alarm has not been disabled. If the condition which initiated the alarm is still present, the Vehicle Security Alarm will ignore that condition and monitor the remaining doors and ignition. To Arm The System Follow these steps to arm the Vehicle Security Alarm: 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle • The driver’s door key cylinder and the liftgate button and open a door, the alarm will sound. If this occurs, on the RKE transmitter cannot arm or disarm the disarm the Vehicle Security Alarm. Vehicle Security Alarm.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security System Manual Override NOTE: The Vehicle Security Alarm will not arm if you lock the • The front courtesy overhead console and door courdoors using the manual door lock plunger. tesy lights will not turn off if the dimmer control is in the “Dome ON” position (rotate horizontal thumb ILLUMINATED ENTRY — IF EQUIPPED wheel on the bottom of the switch to the far right detent position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Two RKE transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three-button RKE transThis system allows you to lock or unlock the doors and liftgate, and activate the Panic Alarm, optional power mitters, and those built with power options will be equipped with up to seven-button RKE transmitters.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob With Three-Button RKE Transmitter Seven-button RKE transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to operate the power liftgate (optional), power sliding doors, Remote Start feature (optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on LOCK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. Press and hold the LOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer This feature lets you program the system to unlock either than 10 seconds. Then, press and hold the UNLOCK the driver’s side, or all doors, on the first press of the button while still holding the LOCK button. UNLOCK button on the RKE transmitter: 3. Release both buttons at the same time. NOTE: 4.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Lock Doors And Liftgate • For vehicles not equipped with the EVIC, perform the following steps: Press and release the LOCK button on the RKE transmitter to lock all doors and liftgate. The turn signal lights 1. Perform this operation while standing outside the will flash and the horn will chirp to acknowledge the vehicle. signal. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: Pressing the LOCK button on the RKE transmit- NOTE: ter while you are in the vehicle will activate the Vehicle • When you turn off the Panic Alarm by pressing the Security Alarm. Opening a door with the Vehicle Security PANIC button a second time, you may have to move Alarm activated will cause the alarm to sound. Press the closer to the vehicle due to the Radio Frequency (RF) UNLOCK button to deactivate the Vehicle Security noises of the system. Alarm.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If equipped with a rear interior switch on the left rear If the vehicle is locked and the Vehicle Security Alarm is pillar, pushing this switch once will close the liftgate only. armed, pressing the LEFT Power Sliding Door button twice unlocks the power sliding door and disarms VeThe liftgate cannot be opened from this switch. hicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Press and hold the UNLOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the LOCK This feature will cause the turn signal lights to flash when button while still holding the UNLOCK button. the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change 3. Release both buttons at the same time. the current setting, proceed as follows: 4.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters If you do not have a programmed RKE transmitter, contact your authorized dealer for details. Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate • Do not touch the battery terminals that are on the back Emergency Key Removal housing or the printed circuit board. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2 Inserting Emergency Key Into Slot Separating RKE Transmitter 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. To assemble the RKE transmitter case, snap the two 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB halves together. radios. General Information This device complies with Part 15 of the FCC rules and REMOTE STARTING SYSTEM — IF EQUIPPED RSS 210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 How To Use Remote Start • System not disabled from previous remote start event All of the following conditions must be met before the • Vehicle theft alarm not active engine will Remote Start: • Ignition in Off position • Shift lever in PARK • Doors closed WARNING! • Hood closed • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped To Enter Remote Start Mode The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prematurely: Press and release the REMOTE START button on the RKE transmitter twice within five seconds. The vehicle doors will lock, the parking lights will flash and horn will chirp twice (if programmed).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of the 15-minute cycle, press and release in the Remote Start mode. the UNLOCK button on the RKE transmitter to unlock • The engine can be started two consecutive 15-minute the doors and disarm the Vehicle Security Alarm (if cycles with the RKE transmitter. However, the ignition equipped).
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Cancel Remote Start To Turn Off The Engine While In Remote Start Remote Starting will also cancel if any of the following Mode Press and release the REMOTE START button 1 time or occur: allow the engine to run for the entire 15 minute cycle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 DOOR LOCKS Manual Door Locks Lock the front doors by pushing down on the lock knobs on each door trim panel. 2 If the lock knob is down when you shut either front door, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Manual Door Lock If the lock knob is rearward when you shut either side sliding door, the door will lock. Make sure the keys are not inside the vehicle before closing the door.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! (Continued) • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with Keyless Enter-NGo™ in the ACC or ON/RUN position. A child could operate power windows, other controls, or move the vehicle. 2 Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob. If you press the power door lock switch while the sliding door is open, the sliding door will lock. Automatic Door Locks — If Equipped When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 The Unlock Doors Automatically On Exit feature will not operate if there is any manual operation of the power door locks (lock or unlock). 2 On vehicles equipped with the optional Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Window Lockout Switch — If Equipped The driver may lock out the rear power windows by depressing the bar switch just below the power window switches. Driver’s Power Window Switches NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening a front door will cancel this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and a set of switches that lock and unlock all doors. The switches will operate only when the ignition switch is in the ON/RUN or ACC position and during power accessory delay.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped Auto Up Feature With Anti-Pinch Protection — If The front window switches may be equipped with an Equipped Auto-Down feature. Press the window switch past the The front driver and front passenger switches may be detent, release, and the window will go down automati- equipped with an Auto Up feature. Lift the window switch fully upward to the second detent, release, and the cally. window will go up automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: Auto Up Reset — If Equipped • If the window runs into any obstacle during auto- To reactivate the Auto Up feature, perform the following closure, it will reverse direction and then go back steps after vehicle power is restored: down. Remove the obstacle and use the window 1. Pull the window switch up to close the window switch again to close the window.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The switches will operate only when the ignition switch NOTE: The sliding door windows do not fully open, is in the ON/RUN or ACC position and during power stopping several inches above the window sill. accessory delay. Wind Buffeting NOTE: The switches will not operate if the driver has Wind buffeting can be described as the perception of activated the Power Window Lockout. pressure on the ears or a helicopter-type sound in the ears.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 rocking forward and back. Rocking the handle back- Always make sure that the sliding door is fully latched wards opens the door and rocking forward releases the anytime the vehicle is in motion. hold open latch in order to close the door. NOTE: The left side sliding door cannot be opened To keep your door operating properly, observe the fol- while the fuel door is open.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pulling the outside power sliding door handle a second time while the sliding door is power opening or power closing will allow the sliding door to be opened or closed manually. Press the button on the RKE transmitter twice within 5 seconds to open a power sliding door. When the door is fully open, pressing the button twice within 5 seconds a second time will close the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 master lock button, located in the overhead console, to • If the power sliding door encounters multiple obstructions within the same cycle, the system will automatidisable the switches and handles for the rear seat cally stop, the power sliding door motor will make a passengers. clicking sound until the door has no further moveNOTE: ment. This clicking sound can be stopped by pulling the inside or outside handle.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Side Door Open Flash The left and right exterior hazard lights will flash for 12 seconds when either sliding door is opened. This will alert other drivers in the area that passenger(s) could be entering or exiting the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. To Engage the Child Protection Door Lock 1. Open the sliding side door.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the Child Protection Door Lock system is engaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the RKE transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the power sliding door. Child Protection Door Lock 3. Repeat Steps 1 and 2 on the opposite sliding door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the sliding doors can only be opened from the outside door handle or the switches located on the trim panel just in front of the power sliding door when the Child Protection Door Locks are engaged. NOTE: • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, press the liftgate release handle located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmitter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within five seconds, a second time, will close the liftgate. 2 The power liftgate may also be opened and closed by pressing the button located on the overhead console.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, and several audible beeps will occur to signal that the located in the upper left trim in the liftgate opening. liftgate is opening or closing. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • During power operation, whether liftgate is fully open • If the power liftgate encounters multiple obstructions or fully closed, the liftgate chime will beep several within the same cycle, the system will automatically stop and must be opened or closed manually. times indicating power operation is in progress. • The power liftgate must be in the full open or close positions for any of the buttons to operate.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • An energy-absorbing steering column and steering wheel Some of the most important safety features in your vehicle are the restraint systems: • Knee bolster for front passenger seat occupant OCCUPANT RESTRAINTS • Three-point lap and shoulder belts for all seating • Front seat belts incorporate pretensioners that may positions enhance occupant protection by managing occupant energy during an impact event • Advanced Front Air Bags for driver and front passen•
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 If you will be carrying children too small for adult-sized seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold infant and child restraint systems. For more information on LATCH, refer to Lower Anchors and Tether for CHildren (LATCH). WARNING! Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger Advanced Front Air Bag.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided as far back as possible and use the proper child restraint. under ⴖIf You Need Assistanceⴖ.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! (Continued) WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air Bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Supplemental Side Air Bag Inflatable Curtain (SABIC) and Seat-Mounted Side Air Bags (SAB) also need room to inflate.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seats in your vehicle are equipped with lap/shoulder belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. 4. Position the lap belt across your thighs, below your abdomen.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Pull the strap down and secure the small latch plate of pushing anywhere on the anchorage. To move the anthe lap belt into the small buckle until you hear a “click”. chorage downward, squeeze the actuation buttons while simultaneously pushing down on the anchorage Position the shoulder belt on your chest so that it is assembly. comfortable and not resting on your neck.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you will prefer a higher position. When you release the If the passenger seating position is equipped with an anchorage, try to move it up or down to make sure that ALR and is being used for normal usage: it is locked in position. Only pull the belt webbing out far enough to comfortably Seat Belts In Passenger Seating Positions wrap around the occupant’s mid-section so as to not The seat belts in the passenger seating positions are activate the ALR.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners Supplemental Active Head Restraints (AHR) The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. 2 NOTE: The Active Head Restraints (AHR) may or may not deploy in the event of a front or side impact.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Resetting Active Head Restraints (AHR) If the Active Head Restraints are triggered in a collision, you must reset the head restraint on the driver’s and front passenger seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 2 Hand Positioning Points On AHR 1 — Downward Movement 2. Position the hands on the top of the deployed AHR at 2 — Rearward Movement a comfortable position. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the Active into the back decorative plastic half. Head Restraints, see an authorized dealer. • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Enhanced Seat Belt Use Reminder System (BeltAlert®) After the sequence completes, the Seat Belt Reminder Light remains illuminated until the respective seat belts are fastened. The driver should instruct all other occupants to fasten their seat belts. If a front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), BeltAlert® will provide both audio and visual notification.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert® can be enabled or disabled by your autho- Seat Belt Extender rized dealer. Chrysler Group LLC does not recommend If a seat belt is too short, even when fully extended and deactivating BeltAlert®.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the air bag covers.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Front Passenger Advanced Front This vehicle may be equipped with Supplemental Side Air Bags are certified to the new Federal regulations for Air Bag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. The Advanced Air Bags. SABIC air bags are located above the side windows and The Advanced Front Air Bags have a multistage inflator their covers are also labeled: SRS AIRBAG. design.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Air Bag System Components • Supplemental Side Air Bag Inflatable Curtains (SABIC) Your vehicle may be equipped with the following air bag • Front and Side Impact Sensors system components: • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, • Occupant Restraint Controller (ORC) and Seat Track Position Sensors • Air Bag Warning Light Advanced Front Air Bag Features • Steering Wheel and Column The Advanced Front Air Bag system has multistage driver an
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • No objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 When the air bag deploys, it opens the seam between the NOTE: front and side of the seat’s trim cover. Each air bag • Should a vehicle rollover occur, the pretensioners deploys independently; a left side impact deploys the left and/or SAB and SABIC air bags on both sides of the air bag only and a right-side impact deploys the right air vehicle may deploy. bag only.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the SABIC is located should remain free from any obstructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. Supplemental Driver Side Knee Air Bag improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE collisions depending on several factors, including the severity and type of collision. Advanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 The ORC contains a backup power supply system that It also includes diagnostics that will illuminate the instrumay deploy the air bags even if the battery loses power or ment cluster Air Bag Warning Light if a malfunction is noted that could affect the air bag system. The diagnosit becomes disconnected prior to deployment. tics also record the nature of the malfunction.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Passenger Advanced Front Air Bag Inflator Units The Driver and Passenger Advanced Front Air Bag Inflator Units are located in the center of the steering wheel and on the right side of the instrument panel. When the ORC detects a collision requiring the Advanced Front Air Bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Advanced Front Air Bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Supplemental Seat-Mounted Side Air Bag (SAB) Inflator Units Supplemental Side Air Bag Inflatable Curtain (SABIC) Inflator Units The Supplemental Seat-Mounted Side Air Bags (SAB) are During collisions where the impact is confined to a designed to activate only in certain side collisions.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because air bag sensors estimate deceleration over time, • Cut off fuel to the engine. vehicle speed and damage are not good indicators of • Flash hazard lights as long as the battery has power or whether or not an air bag should have deployed. until the ignition key is turned off. NOTE: In a rollover the pretensioners and/or SAB and • Turn on the interior lights, which remain on as long as SABIC air bags may deploy on both sides of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 These data can help provide a better understanding of Child Restraints the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all NOTE: EDR data are recorded by your vehicle only if a times, including babies and children.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it. NOTE: For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/ eng/roadsafety/safedrivers-childsafety-index-53.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 4. Is the lap part of the belt as low as possible, touching over the front of the seat when their back is against the the child’s thighs and not their stomach? seatback, should use the seat belt in a rear seat. Use this 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Recommendations For Attaching Child Restraints Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 LATCH Positions For Installing Child Restraints In This Vehicle 2 Second Row Bench Second Row Captains Chairs Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint LATCH Positions What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes; second row outboard positions only, third row all positions. Never “share” a LATCH anchorage with two or more child restraints.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Locating The LATCH Anchorages In addition, there are tether strap anchors located behind each rear seatback, near to the floor.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems will be Center Seat LATCH – Commercial Cargo Vehicles equipped with a rigid bar or a flexible strap on each side. (No Factory Installed Rear Seats) — If Equipped Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the WARNING! anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Center Seat LATCH To Install A LATCH-compatible Child Restraint If a child restraint installed in the center position blocks 1. If the selected seating position has a Switchable Autothe seat belt webbing or buckle for the outboard position, matic Locking Retractor (ALR) seat belt, stow the seat do not use that outboard position. If a child seat in the belt, following the instructions below.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can Improper installation of a child restraint to the be “switched” into a locked mode by pulling all of the LATCH anchorages can lead to failure of the re- webbing out of the retractor and then letting the webbing straint. The child could be badly injured or killed. retract back into the retractor.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle Second Row Bench Second Row Captains Chair
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 Lap/Shoulder Belt Systems What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Yes; second row outboard positions only, third row all positions.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 8. If the child restraint has a top tether strap and the Installing A Child Restraint With A Cinching seating position has a top tether anchorage, connect Latch Plate (CINCH) — If Equipped the tether strap to the anchorage and tighten the tether 1. Place the child seat in the center of the seating strap. Refer to “Lower Anchors and Tethers for Chilposition.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Finally, pull up on any excess webbing to tighten the Any seat belt system will loosen with time, so check the lap portion around the child restraint while you push belt occasionally, and pull it tight if necessary. the child restraint rearward and downward into the If the buckle or the cinching latch plate is too close to the vehicle seat. belt path opening of the child restraint, you may have 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 Installing Child Restraints Using The Top Tether Anchorage 3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 COMMERCIAL CARGO VEHICLES (NO FACTORY INSTALLED REAR SEATS) — IF EQUIPPED Commercial cargo vehicles are not designed for use as a family vehicle and are not intended for carrying children in the front passenger seat. However, if you must carry a child in a vehicle without a rear seat, the passenger seat should be moved to the full rearward position and the child must be in a proper restraint system based on its age, size and weight.
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal anchor on the lower rear of the front passenger There are different sizes and types of restraints for seat. children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is 4. Following the child seat manufacturer’s instructions, correct for your child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to A long break-in period is not required for the engine and “Maintenance Procedures” in “Maintaining Your Vedrivetrain (transmission and axle) in your vehicle. hicle”. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or CAUTION! 55 mph (80 or 90 km/h) are desirable.
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 119 The best protection against carbon monoxide entry into Safety Checks You Should Make Inside The the vehicle body is a properly maintained engine exhaust Vehicle system. Seat Belts Whenever a change is noticed in the sound of the exhaust Inspect the belt system periodically, checking for cuts, system, when exhaust fumes can be detected inside the frays, and loose parts.
120 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 121 WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals.
122 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 ▫ Inside Day/Night Mirror — If Equipped . . . .130 ▫ Automatic Dimming Mirror — If Equipped . . .131 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .132 ▫ Driver’s Outside Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .132 ▫ Outside Mirrors Folding Feature . . . . . . . . . .132 ▫ Power Mirrors — If Equipped . . . . . . . . . . . .
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .155 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .187 ▫ Uconnect® Phone Features . . . . . . . . . . . . . . .158 ▫ Manual Front/Second Row Seat Adjuster . . . .190 ▫ Advanced Phone Connectivity . . . . . . . . . . . .163 ▫ Manual Reclining Seats — If Equipped . . . . . .191 ▫ Things You Should Know About Your Uconnect® Phone . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .214 ▫ Dimmer Controls . . . . . . . . . . . . . . . . . . . . .224 ▫ Setting Memory Positions And Linking RKE Transmitter To Memory . . . . . . . . . . . . .215 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . .226 ▫ Easy Entry/Exit Seat (Available With Memory Seat ONLY) . . . . . . . . . . . . . . . . . . .218 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . . .219 䡵 LIGHTS . . . . . . . . . . . . . . . . . . .
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 TILT/TELESCOPING STEERING COLUMN . . .232 䡵 PARKSENSE® REAR PARK ASSIST — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .239 䡵 HEATED STEERING WHEEL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .233 ▫ ParkSense® Sensors . . . . . . . . . . . . . . . . . . . .240 䡵 ADJUSTABLE PEDALS — IF EQUIPPED . . . . . .234 ▫ ParkSense® Warning Display . . . . . . . . . . . . .240 䡵 ELECTRONIC SPEED CONTROL — IF EQUIPPED . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 ▫ Turning ParkView® On Or Off — Without Navigation/Multimedia Radio . . . . . . . . . . . .251 ▫ Reprogramming A Single HomeLink® Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 䡵 OVERHEAD CONSOLES . . . . . . . . . . . . . . . . .251 ▫ Canadian/Gate Operator Programming . . . . . .261 ▫ Front Overhead Console. . . . . . . . . . . . . . . . .251 ▫ Using HomeLink®. . . . . . . . . . . . . . . . . . . . .
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Venting Sunroof — Express . . . . . . . . . . . . . .268 ▫ Interior Bottle Holders . . . . . . . . . . . . . . . . . .278 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . . .268 ▫ Smoker’s Package Kit — If Equipped . . . . . . .279 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .268 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .279 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 䡵 CONSOLE FEATURES . . . . . . . . . . . . . . . . . . .286 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . . .296 ▫ Basic Console . . . . . . . . . . . . . . . . . . . . . . . .287 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .296 ▫ Premium Console — If Equipped . . . . . . . . . .288 䡵 LOAD LEVELING SYSTEM — IF EQUIPPED . . .298 ▫ Super Console — If Equipped. . . . . . . . . . . . .292 䡵 ROOF LUGGAGE RACK — IF EQUIPPED . . . .
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. 3 NOTE: This feature is disabled when the vehicle is moving in reverse.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Driver’s Outside Automatic Dimming Mirror — If To receive maximum benefit, adjust the outside mirror(s) Equipped to center on the adjacent lane of traffic with a slight The driver’s outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 The power mirror controls consist of mirror select butThe power mirror controls are located on the driver-side tons and a four-way mirror control switch. To adjust a mirror, press either the L (left) or R (right) to select the door trim panel. mirror that you want to adjust. Power Mirrors — If Equipped NOTE: A light in the selected button will illuminate indicating the mirror is activated and can be adjusted.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended. Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: If the vehicle speed is greater than 10 mph • The mirrors come out of the unfolded position. (16 km/h) the folding feature will be disabled. • The mirrors shake and vibrate at normal driving If the mirrors are in the folded position, and vehicle speeds. speed is equal or greater than 10 mph (16 km/h), they To reset the power folding mirrors : Fold and unfold will automatically unfold. them by pressing the button.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Automatic Transmission vehicles The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when the vehicle is in PARK. Manual Transmission vehicles The BSM system sensors operate when the vehicle is in any gear and enters stand-by mode when the Park Brake is engaged, the vehicle is not in REVERSE, and the vehicle is stationary.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the detection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. 3 BSM Warning Light The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Rear Vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 3 Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc. However, occasionally the system may alert adjacent lanes. on such objects. This is normal operation and your vehicle does not require service.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death. Rear Cross Path Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE view mirror based on a detected object. However, when the system is operating in RCP, the system will respond Modes Of Operation With EVIC with both visual and audible alerts when a detected Three selectable modes of operation are available in the object is present. Whenever an audible alert is requested, Electronic Vehicle Information Center (EVIC). Refer to the radio is muted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The BSM system will store the current operating • Whenever an audible alert is requested by the BSM mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and system, the radio is also muted. used • If the hazard flashers are on, the system will request Uconnect® Phone — IF EQUIPPED the appropriate visual alert only.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE long as your phone is turned on and has been paired to the vehicle’s Uconnect® Phone. The Uconnect® Phone • U.S. residents - visit www.UconnectPhone.com or call allows up to seven mobile phones to be linked to the 1–877–855–8400. system. Only one linked (or paired) mobile phone can be • Canadian Residents - visit www.UconnectPhone.com used with the system at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 The Uconnect® Phone is fully integrated with the vehicle’s audio system. The volume of the Uconnect® Phone The radio or steering wheel controls (if can be adjusted either from the radio volume control equipped) will contain the two control buttons knob or from the steering wheel radio control (right button and Voice Com(Uconnect® Phone switch), if so equipped. mand button) that will enable you to access the system.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be used. For example, instead of saying “Setup” and then “Pair a Device”, the following compound command can be said: “Pair a Bluetooth® Device”. Help Command Voice Command Tree Pair (Link) Uconnect® Phone To A Mobile Phone Refer to “Voice Tree” in this section. To begin using your Uconnect® Phone, you must pair your compatible Bluetooth® enabled mobile phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To complete the pairing process, you will need to refer- • For identification purposes, you will be prompted to give the Uconnect® Phone a name for your mobile ence your mobile phone Owner’s Manual. The phone. Each mobile phone that is paired should be Uconnect® website may also provide detailed instrucgiven a unique phone name. tions for pairing.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say the name of the person you want to call. For example, • Press the button to begin. you can say “John Doe”, where John Doe is a previ• After the “Ready” prompt and the following beep, say ously stored name entry in the Uconnect® phonebook “Dial”. or downloaded phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 • When prompted, say the name of the new entry. Use of long names helps the Voice Command and it is recommended. For example, say “Robert Smith” or “Robert” instead of “Bob”. • When prompted, enter the number designation (e.g., “Home”, “Work”, “Mobile”, or “Other”). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. only in that language.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • A maximum of 1000 entries per phone will be down- Edit Uconnect® Phonebook Entries loaded and updated every time a phone is connected NOTE: Editing phonebook entries is recommended to the Uconnect® Phone. when the vehicle is not in motion. Automatic down• Depending on the maximum number of entries down- loaded phonebook entries cannot be deleted or edited. loaded, there may be a short delay before the latest button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 After you are finished editing an entry in the phonebook, • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish you will be given the opportunity to edit another entry in to delete. You can either say the name of a phonebook the phonebook, call the number you just edited, or return entry that you wish to delete or you can say “List to the main menu.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” Uconnect® Phonebook Entries List All Names In The Uconnect® Phonebook • Press the • Press the button to begin. button to begin. • After the “Ready” prompt and the following beep, say • After the “Ready” prompt and the following beep, say “Phonebook Erase All”. “Phonebook List Names”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Answer Or Reject An Incoming Call — Call The following features can be accessed through the Currently In Progress Uconnect® Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE in progress. To go back to the first call, refer to “Toggling Conference Call Between Calls” in this section. To combine two calls, refer When two calls are in progress (one active and one on to “Conference Call” in this section. button until you hear a hold), press and hold the double beep indicating that the two calls have been Place/Retrieve A Call From Hold joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 active call is terminated by the phone far end, a call on Call Continuation hold may not become active automatically. This is cell Call continuation is the progression of a phone call on the phone-dependent. To bring the call back from hold, press Uconnect® Phone after the vehicle ignition has been button until you hear a single beep. and hold the switched to OFF.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone Features Emergency Assistance Language Selection If you are in an emergency and the mobile phone is reachable: To change the language that the Uconnect® Phone is using: • Pick up the phone and manually dial the emergency number for your area. button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available mobile service and area. WARNING! To use you Uconnect® Phone System in an emergency, your mobile phone must be: • turned on, • paired to the Uconnect® System, • and have network coverage.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: You should program the desired Towing Assistance phone number using the Voice Command system. To do this, press the button and say “Setup”, followed by “Towing Assistance”. When prompted say 1-800-5282069 for the U.S., say 1-800-363-4869 for Canada, say 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 “Send”, is also to be used for navigating through an NOTE: automated customer service center menu structure, and • You may not hear all of the tones due to mobile phone to leave a number on a pager. network configurations. This is normal.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts ON/OFF using Uconnect® Phone. The status is given for network signal strength, phone battery strength, etc. Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect® Phone Dialing Using The Mobile Phone Keypad will not repeat a phone number before you dial it). You can dial a phone number with your mobile phone keypad and still use the Uconnect® Phone (while dialing button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 from your Uconnect® Phone paired mobile phone to the Uconnect® Phone or vice versa, press the button When you mute the Uconnect® Phone, you will still be and say “Transfer Call”. able to hear the conversation coming from the other party, but the other party will not be able to hear you. In Connect Or Disconnect Link Between The order to mute the Uconnect® Phone: Uconnect® Phone And Mobile Phone Mute/Un-Mute (Mute ON/OFF) • Press the button.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the • The Uconnect® Phone will play the phone names of all Uconnect® Phone will return to using the highest paired mobile phones in order from the highest to the priority phone present in or near (approximately lowest priority. To “Select” or “Delete” a paired phone within 30 ft. (9 m)) the vehicle. button and say “Sebeing announced, press the lect” or “Delete”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Things You Should Know About Your Uconnect® Phone Uconnect® Phone Tutorial • Press the button and say the “Voice Training”, “System Training”, or “Start Voice Training” command. To hear a brief tutorial of the system features, press the You can either press the Uconnect® Phone button to restore the factory setting or repeat the words and button and say “Uconnect® Tutorial.” phrases when prompted by the Uconnect® Phone.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This will delete all phone pairing, phone book entries, • Performance is maximized under: and other settings in all language modes. The System will • low-to-medium blower setting, prompt you before resetting to factory settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • It is not recommended to store similar sounding names Far End Audio Performance in the Uconnect® Phonebook. • Audio quality is maximized under: • Phonebook (Downloaded and Uconnect® Phone Lo• low-to-medium blower setting, cal) name recognition rate is optimized when the • low-to-medium vehicle speed, entries are not similar. • low road noise, • Numbers must be spoken in single digits.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recent Calls • Uconnect® Phone will play the new text message for you. If your phone supports “Automatic Phonebook Download”, Uconnect® Phone can list your Outgoing, Incom- After reading a message, you can “Reply” or “Forward” ing and Missed Calls. the message using Uconnect® Phone. Voice Text Reply Send Messages: Uconnect® Phone can read or send new messages on You can send messages using Uconnect® Phone. To send your phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Uconnect® Phone will prompt you to say the name or 10. number of the person you wish to send the message to. 11. List of Preset Messages: 12. 1. Yes 13. 2. No 14. 3. Where are you? 15. 4. I need more direction. 16. 5. L O L 17. 6. Why 18. 7. I love you 19. 8. Call me 20. 9.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Voice Text Reply Incoming Announcement ON/ Bluetooth® Communication Link OFF Mobile phones have been found to lose connection to the Turning the Voice Text Reply Incoming Announcement Uconnect® Phone. When this happens, the connection OFF will stop the system from announcing the new can generally be reestablished by switching the phone off/on. Your mobile phone is recommended to remain in incoming messages. Bluetooth® ON mode. button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 3
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 3
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Voice Commands Primary Alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book Voice Commands Primary Alternate (s) previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect® Tutorial voice training work yes 3
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Pressing the Voice Command button while the system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To hear the first available Menu, press the Voice Com- Main Menu button and say “Help” or “Main Menu”. mand Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the Commands main menu. The Voice Command system understands two types of commands. Universal commands are available at all In this mode, you can say the following commands: times.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Radio AM • “Menu Radio” (to switch to the radio menu) To switch to the AM band, say “AM” or “Radio AM”. In • “Main Menu” (to switch to the main menu) this mode, you may say the following commands: Satellite Radio • “Frequency #” (to change the frequency) To switch to satellite radio mode, say “Sat” or “Satellite Radio”.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disc Mode Bluetooth® Streaming (BT) Mode To switch to the disc mode, say “Disc”. In this mode, you To switch to Bluetooth® Streaming (BT) mode, say “Bluetooth Streaming”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice Combutton to stop playing memos.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect® vehicle. Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Power Seats — If Equipped Some models may be equipped with eight-way power seats for the driver and front passenger. The power seat switches are located on the outboard side of the seat. The switches control the movement of the seat cushion and the seatback.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions. Pull upward or push downward on the front or rear of the seat switch, the front or rear of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been reached. Reclining The Seatback The angle of the seatback can be adjusted forward or rearward.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Heated Seats — If Equipped Vehicles Equipped With Remote Start On some models, the front and rear seats may be On models that are equipped with remote start, the equipped with heaters located in the seat cushions. driver’s heated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things To Know Before WARNING! Starting Your Vehicle” for further information.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. HIGH-level. If the HIGH-level setting is selected, the system will automatically switch to LOW-level after approximately 60 minutes of continuous operation. At that time, the display will change from HIGH to LOW, indicating the change.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the HIGH-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal HIGH-level. If the HIGH-level setting is selected, the system will automatically switch to LOW-level after approximately 60 minutes of continuous operation. At that time, the display will change from HIGH to LOW, indicating the change.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Active Head Restraint (Normal Position) Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints — Third Row The head restraint in the center position can be raised and lowered for tether routing. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. Stow ’n Go® Seating — If Equipped On vehicles equipped with Stow ’n Go® seating, the second and third row seats can be folded into the floor for convenient storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 NOTE: Seat will not stow in the storage bin unless the 5. Pull upward on the seatback recliner lever located on armrests are raised. the outboard side of the seat. 4. Slide the storage bin locking mechanism to the “LOCK” position and then pull up on the storage bin latch to open the cover.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Non-Adjustable Head Restraint Automatic Folding Seatback The seat will automatically tumble into position for easy storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 3 Tumbled Second Row Seat 6. Push the seat into the storage bin. Seat In Storage Bin 7. Close the storage bin cover. CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In a collision, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open. • Keep the storage bin covers closed and latched while the vehicle is in motion. • Do not use a storage bin latch as a tie down. To Unstow Second Row Seats 1. Pull up on the storage bin latch to open the cover. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 3 Raising The Seatback 2. Return the head restraint to the upright position. Raising The Head Restraint 3. Pull up on the seatback recliner lever on the outboard side of the seat to fold head rest and seatback and tumble seat forward.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The seat will automatically fold into position for easy The second row Stow ’n Go® seats allow easy entry to the entry into the third row. third row seat or rear cargo area. Easy Entry Second Row Pull up on the seatback recliner lever on the outboard side of the seat. WARNING! In the event of a collision you could be injured if the seat is not fully latched. Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat To fold the seat, lift the recliner lever to the full upward position and push the seatback forward until it rests on the seat cushion. Recline Lever WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 For passengers seated in the third row, there is a pull The Quad seats can be tilted forward for easy entry into strap located on the outboard side of the seat near the the third row. With the Quad seat in the fold-flat position, bottom of the seat back. Third row passengers can pull on the strap and push the Quad seat forward for folding the lift up on the easy entry lever located near the bottom of seatback and accessing the easy entry lever.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removal Second Row Bench Seat — If Equipped The Quad seats can be removed if additional storage is While the bench seat does not stow in the floor, it is needed. With the seat in the easy entry position, lift the removable for added cargo space. cross beam forward and up to release the front anchor latches. Second Row Bench Seat Cross Beam For Seat Removal Release levers are located on the rear leg assemblies, near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 indicator button pops up when the seat is unlocked. The upward until the lock indicator button returns into the seat assembly can now be removed from the vehicle and handle. moved on its Easy Out® Rollers. WARNING! If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstalling these seats, be sure the red indicator button on the release handles return into the handles.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Lower the head restraint by pulling on the release strap marked “1” located on the outboard side of the head restraint. Third Row Power Seat Switch Third Row Power Folding Seat — If Equipped A one-touch power folding seat switch is located in the left rear trim panel as part of a switch bank. Head Restraint Release Strap “1” The switch is only functional when the liftgate is open and the vehicle is in PARK.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 the following positions using the switch bank located on the left rear trim panel: 3 One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Rear Panel Power Switch Bank Left and right third row seats can be folded individually 1 — Open to Normal or together.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Manually Folding Third Row Seats — If Equipped • Disconnect the center shoulder belt from the small 1. Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the buckle and lower the head restraints before attempting head restraint down. to fold/stow the power third row seats. • To abort seat operation while seat is in motion, press a 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 3 Head Restraint Release Strap “1” Release Strap “2” 3. Pull release strap marked “2” located on the rear of the 4. Pull release strap marked “3” to release the anchors. seat to lower the seatback.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Release Strap “3” 5. Pull release strap marked “4” and tumble the seat rearward into the storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 2. Pull release strap marked “2” to unlock the recliner. 3. Pulling strap “4” releases the seatback to return to its full upright position. 4. Raise the head restraint to its upright position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Stowed Third Row Seat To Unfold Third Row Seats 1.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tailgate Mode Plastic Grocery Bag Retainer Hooks 1. Pull release strap “3”, then pull release strap “4” to Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and rotate the entire seat rearward. some front seats. The floor supports the partial weight of 2. To restore the seat to its upright position, lift up on the the bagged goods. seatback and push forward until the anchors latch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Setting Memory Positions And Linking RKE Transmitter To Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) is pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the ON position. 2. Press the driver door MEMORY button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up 11. Select “Remote Linked to Memory” in the Electronic to 10 AM and 10 FM stations can be set). Vehicle Information Center (EVIC) and enter “Yes”. Refer to “Electronic Vehicle Information Center 6. Turn the ignition switch to the OFF position and (EVIC)/Customer-Programmable Features” in “Unremove the key. derstanding Your Instrument Panel” for further in7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 To recall the memory setting for driver two, press MEMORY 3. Press and release the memory SET (S) button located on the driver’s door. A chime will sound signaling that button 2 on the driver’s door or the UNLOCK button on the you are in the memory set mode. RKE transmitter linked to Memory Position 2. A recall can be cancelled by pressing any of the 4. Within five seconds, press and release MEMORY button 1 on the driver’s door.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features⬙ in “Understanding • Your Instrument Panel” for further information. Easy Entry/Exit Seat (Available With Memory Seat ONLY) This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 NOTE: The Easy Entry/Easy Exit feature can be enabled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). If your vehicle is not equipped with an EVIC, your dealership can activate/deactivate this feature for you. For details, refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Safety Lever Location Hood Prop Rod Use the hood prop rod to secure the hood in the open position. CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 in (30 cm) and then drop it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 CAUTION! (Continued) secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! 3 Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE vehicles equipped with an automatic headlight system. Refer to “Electronic Vehicle Information Center (EVIC)/ This system automatically turns your headlights on or off Customer-Programmable Features” in “Understanding based on ambient light levels. To turn the system on, turn Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 The headlight delay time is programmable on vehicles equipped with an EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. Daytime Running Lights — If Equipped The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lighting On Dimmer Controls The dimmer switch is located next to the headlight Rotate the left dimmer control completely upward to the switch. second detent (extreme top position) to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 NOTE: The key must be out of the ignition switch or the The Halo control switch is located to the right of the ignition switch must be in the OFF position for this dimmer switch. feature to operate. Interior Lighting Off Rotate the left dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. 3 Parade Mode (Daytime Brightness Feature) Rotate the left dimmer control to the first detent.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever controls the: The multifunction lever is located on the left side of the • Turn Signals steering column. • Headlight Beams Low/High • Flash-To-Pass (Optical Horn) • Front and Rear Wipers — Washer Functions Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 Turn Signal Warning Flash-To-Pass If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver. You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Always remove any buildup of snow that preThe wipers and washers are operated by a switch within vents the windshield wiper blades from returning to the the multifunction lever. Rotate the end of the multifunc- off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage tion lever to select the desired wiper speed. to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 Intermittent Wiper System Windshield Washers Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the multifunction lever to the first detent position, and then turn the end of the lever to select the desired delay interval.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Wiper And Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermittent interval. NOTE: Rear window wipers function in the intermittent wiper speed only. Rain Sensing Wipers — If Equipped The sensitivity of the system is adjustable from the multifunction lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 • The Rain Sensing feature can be turned on and off • Neutral Wipe Inhibit — The Rain Sensing feature will through the EVIC (if equipped).
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 The heated steering wheel switch is located on the switch The steering wheel contains a heating element that helps bank below the climate controls. There are also soft-keys warm your hands in cold weather. The heated steering in the radio screen that will activate the heated steering wheel. wheel has only one temperature setting.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With Remote Start WARNING! (Continued) On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The Electronic Speed Control buttons are located on the right side of the steering wheel. Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate To Vary The Speed Setting A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory. When the Electronic Speed Control is set, you can increase speed by pushing the RES (+) button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 Pressing the SET (-) button once will result in a 1 mph (1.6 km/h) decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph (1.6 km/h). To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® will retain the last system state (enabled or ParkSense® Warning Display disabled) from the last ignition cycle when the ignition is The ParkSense® Warning screen will only be displayed if changed to the ON/RUN position. Sound and Display is selected from the Customer- ProParkSense® can be active only when the shift lever is in grammable Features section of the Electronic Vehicle REVERSE.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 ParkSense® Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Park Assist System OFF The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 3 Fast Tone Continuous Tone
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 Enabling/Disabling ParkSense® ParkSense® can be enabled and disabled through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If “PARKSENSE UNAVAILABLE WIPE REAR SEN- ParkSense® System Usage Precautions SORS” appears in the Electronic Vehicle Information NOTE: Center (EVIC) make sure the outer surface and the underside of the rear fascia/bumper is clean and clear of • Ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the ParkSense® system opersnow, ice, mud, dirt or other obstruction and then cycle ating properly. the ignition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 • ParkSense®, when on, will MUTE the radio when it is • On vehicles equipped with a tailgate, ParkSense® sounding a tone. should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE. A • Clean the ParkSense® sensors regularly, taking care lowered tailgate could provide a false indication that not to scratch or damage them. The sensors must not an obstacle is behind the vehicle.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using ParkSense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 4. Enable or disable the rear camera feature by selecting OVERHEAD CONSOLES the “enable rear camera in reverse” soft-key. Front Overhead Console 5. Press the “save” soft-key. Two versions of the overhead console are available. The base front overhead console model featured fixed incanTurning ParkView® On Or Off — Without descent courtesy/reading lights, flip-down sunglass storNavigation/Multimedia Radio age and conversation mirror. The premium front over1.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows (LED lamps only).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 Sunglass Storage (Non-Sunroof Only) The door will slowly rotate to the full open position. At the front of the overhead console, a compartment is provided for the storage of two pairs of sunglasses. From the closed position, press the door latch to open the compartment. 3 Full Open Position From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, positioned for conversation mirror use.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 3 Reading Lights Rear Overhead Consoles — If Equipped Overhead Compartment Features 1 — DVD* The rear overhead storage system is available in two 2 — Rear HVAC 3 — Interior Lights versions: with or without sunroof. 4 — Storage An additional LED at the front of the rear console shines * If equipped, otherwise storage. down on the front foot-well area while in courtesy mode, for added convenience.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights — If Equipped” in “Understanding the Features Of Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink® buttons (I and III) for up 20 seconds or until the red indicator flashes.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) 5. At the garage door opener motor (in the garage), away from the HomeLink® button you wish to prolocate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is gram while keeping the HomeLink® indicator light in attached to the garage door opener/device motor. view. Firmly press and release the “LEARN” or “TRAIN3.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the garage door opener/device does not acti- 3. Simultaneously press and hold both the Homelink® button you want to program and the hand-held transvate, press the button a third time (for two seconds) to mitter button. complete the training. To program the remaining two HomeLink® buttons, 4. Continue to hold both buttons and observe the indirepeat each step for each remaining button. DO NOT cator light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Reprogramming A Single HomeLink® Button Canadian/Gate Operator Programming To reprogram a channel that has been previously trained, For programming transmitters in Canada/United States follow these steps: that require the transmitter signals to “time-out” after several seconds of transmission. 1. Turn the ignition switch to the ON/RUN position. Canadian radio frequency laws require transmitter sig2.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE It may be helpful to unplug the device during the cycling 4. Watch for the HomeLink® indicator to change flash process to prevent possible overheating of the garage rates. When it changes, it is programmed. It may take door or gate motor. up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 1. Cycle the ignition to the ON/RUN position. 5. Press and hold the programmed HomeLink® button 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 Reprogramming A Single HomeLink® Button Using HomeLink® To reprogram a channel that has been previously trained, To operate, press and release the programmed follow these steps: HomeLink® button. Activation will now occur for the programmed device (i.e., garage door opener, gate opera1. Cycle the ignition to the ON/RUN position. tor, security system, entry door lock, home/office light2. Press and hold the desired HomeLink® button until ing, etc.,).
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips If you are having trouble programming HomeLink®, here are some of the most common solutions: • Replace the battery in the original hand-held transmitter. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code. • Did you unplug the device for programming and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 General Information NOTE: This device complies with FCC rules Part 15 and Industry • The transmitter has been tested and it complies with Canada RSS-210. Operation is subject to the following FCC and IC rules. Changes or modifications not extwo conditions: pressly approved by the party responsible for compliance could void the user’s authority to operate the 1. This device may not cause harmful interference. device. 2.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch WARNING! • Never leave children unattended in a vehicle, and do not leave the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Press the switch rearward and release it within one-half Close operation, any movement of the switch will stop second. The sunroof and sunshade will open automatithe sunroof. cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “Express Closing Sunroof — Manual Mode Open”.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Venting Sunroof — Express Wind Buffeting Press and release the Vent button within one half second and the sunroof will open to the vent position. This is called “Express Vent”, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof. Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 Ignition Off Operation Sunroof Fully Closed For Vehicles Not Equipped With The Electronic Vehicle Press the switch forward and release to ensure that the Information Center (EVIC) sunroof is fully closed. The power sunroof switch will remain active for 45 ELECTRICAL POWER OUTLETS — IF EQUIPPED seconds after the ignition switch is turned to the LOCK position.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Instrument Panel Outlets • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 3 Removable Console Outlet Super Console Outlets On vehicles equipped with the Super Console the power outlets are located under the retractable cover. To access the power outlets push down on the cover and slide it toward the instrument panel. The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both controlled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps).
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source. The power outlet, located on the lower instrument panel, is powered directly from the battery. Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage. POWER INVERTER — IF EQUIPPED A 110 Volt, 150 Watt inverter outlet (if equipped) converts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Cupholders variety of container types and sizes. Press down on the container to engage the cupholder retention features. The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin. Super Console — If Equipped On models equipped with the Super Console, there are two cupholders located in the center of the console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 For rear passengers two cupholders are located in the pull-out drawer, located in the back of the Super Console. Pull the drawer out to the first position to use the cupholders. Premium Console Cupholders — If Equipped On models equipped with premium center consoles, there are four cupholders located on the top of the console.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommodates up to a 20 oz (.6 L) plastic bottle. WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 Smoker’s Package Kit — If Equipped STORAGE With the optional authorized dealer-installed Smoker’s Glove Compartments Package Kit, a removable ash receiver is inserted into one Upper and lower glove compartments are located on the of the two cupholders in the center front instrument passenger side of the instrument panel. panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward.
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Upper Glove Compartment Lower Glove Compartment To open the upper compartment, press in on the button, To open the lower compartment pull out on the release located on the left side of the upper door. The door will handle. automatically open. Lower Compartment Upper Compartment NOTE: The lower compartment is equipped with a lock To close the compartment door, push downward on the that is part of the compartment handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage. 3 Driver Seatback Storage — If Equipped The driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Umbrella Holder Second Row Seat Storage Bins — If Equipped An umbrella holder has been conveniently molded into The seat storage bins are located on the floor in front of the left front door entry scuff molding. the second row seats. The area below the covers can be used for storage when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 CAUTION! NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. 3 WARNING! Storage Bin In a collision, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open. • Keep the storage bin covers closed and latched while the vehicle is in motion.
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning WARNING! (Continued) Carefully follow these warnings to help prevent personal injury or damage to your vehicle: WARNING! • Always close the storage bin covers when your vehicle is unattended. • Do not allow children to have access to the second row seat storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES There are three consoles available: Basic, Premium and Super. WARNING! Rear Cargo Area Loading Limit NOTE: With all rear seats stowed or removed, 4 x 8 foot sheets of building material will fit on the vehicle floor with the liftgate closed. The front seats must be moved slightly forward of the rearmost position. Do not operate this vehicle with a console compartment lid in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 Basic Console To Remove The Basic Floor Console Basic Console features consist of the following: 1. Remove the front anchor cup plug and clip. • The basic console profile allows vehicle occupants to 2. Slide the console base forward while lifting slightly to easily pass through the first row to the second. clear the rear load floor hook. • Four cupholders accept up to extra large size beverage 3. Remove the console. cups or 20 oz (.6 L) plastic bottles.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Reinstall the clip first and then while pushing down- • Four cupholders with dishwasher safe liners for cleaning. The cupholders can accept plastic bottles, large ward on the console with slight pressure, reinstall the cups or mugs with handles. cover plug. 5. Pull up on the console to be sure it is firmly latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles. 3 Position 1 shows the console closed with four cupholders and a convenient storage tray. Console Position 1 Position 2 shows the raised storage tray revealing a large storage area below.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Position 2 Console Position 3 Position 4 shows the complete console in its rearmost Position 3 shows the top portion of the console in a position. Again, lifting second latch handle at the front of rearward position. This is accomplished by lifting the the console, allows complete access to a lower storage bin and provides additional cupholders for rear passengers. upper most latch at the front of the console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the console. 2. Lift the rear of the console up several inches/ centimeters. 3. Pull rearward to disengage from floor and remove console. To Reinstall The Premium Floor Console: Console Position 4 1. Position the console at a slight angle (rear slightly higher than the front). 2. Slide the console forward into the floor bracket. 3.
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Push down on the rear of the console until it is seated in the rear floor bracket. 5. Pull up on the console to be sure it is firmly latched. WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 NOTE: The front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for the rear passengers.
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RAM CARGO VAN FEATURES Ram Cargo Van Load Floor The Ram Cargo Van receives a structural aluminum rear load floor. Two load floor options are available, the standard floor with a flat aluminum surface and non skid strips or an optional deluxe floor with a flat aluminum surface and non skid strips, through-the-floor access to three storage bins and four load floor tie downs. WARNING! Do not operate the vehicle with loose items stored on the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 3 Standard Load Floor Deluxe Load Floor Storage Bin Locations (Rear View)
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 NOTE: • You can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second time. • To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window.
298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD LEVELING SYSTEM — IF EQUIPPED ROOF LUGGAGE RACK — IF EQUIPPED The automatic load leveling system will provide a level- The crossbars on your vehicle are delivered stowed riding vehicle under most passenger and cargo loading within the roof rack side rails. If adding cargo, deploy the conditions. crossbars. Distribute cargo weight evenly on the roof rack crossbars, to maximum of 150 lbs (68 kg).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 NOTE: • Crossbars are error-proofed and cannot be deployed or stowed in the incorrect positions. • To help control wind noise, stow the crossbars in the side rails when they are not in use. Deploying the Crossbars To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar from its stowed position in the side rail. Repeat with crossbar on the opposite side.
300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Use care when removing and handling the crossbars to prevent damage to the vehicle. Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 3 Stowed Position Deployed Position Then, position the crossbars across the roof. NOTE: The crossbars are identical and can be placed in any two of the three deploy positions.
302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deploy Positions – Choose Two Of Three Crossbar To Side Rail Installation Make sure the directional arrows on the crossbars align Once the crossbars are set into position, tighten the with the directional arrows on the side rails. Set the thumb screws completely. crossbars into the deployed positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 Stowing the Crossbars Reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest. Once the crossbars are stowed, tighten the thumb screws completely. NOTE: Load should always be secured to crossbars first, with rail tie down loops used as additional securing points if needed. Tie loops are intended as supplementary tie down points only.
304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without the crossbars deployed. • The load should be secured and placed on top of the crossbars, not directly on the roof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load.
306 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sun Screen Retracted Sun Screen Extended Gently pull up on the tab to raise the sun screen. To lower the sun screen, gently lift the tab upward to Continue pulling the sun screen until the tab is near the disengage the hooks, and feed the screen back into the top of the window. base sill. Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .312 ▫ Oil Change Required . . . . . . . . . . . . . . . . . . .339 䡵 INSTRUMENT CLUSTER — BASE . . . . . . . . . .313 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . . .340 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . . .314 ▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . .342 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .315 ▫ Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . .
308 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Uconnect® 730N/430/430N CD/DVD/HDD/ NAV — IF EQUIPPED . . . . . . . . . . . . . . . . . . .353 ▫ Operation Instructions — CD MODE for CD and MP3 Audio Play . . . . . . . . . . . . . . . .369 ▫ Operating Instructions (Voice Command System) — If Equipped . . . . . . . . . . . . . . . . .353 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . . .371 ▫ Operating Instructions (Uconnect® Phone) — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 309 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . .383 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . . .385 ▫ Bluetooth Streaming Audio (BTSA) . . . . . . . . .387 䡵 UCONNECT® MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES™) — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ Getting Started . . . . . . . . . . . . . . . . . . . . . . .388 ▫ Blu-ray Player . . . . . . . . . . . . . . . . . . . . . . . .
310 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Headphones Operation . . . . . . . . . . . . . . . . .412 ▫ Listening To Audio With The Screen Closed . . .422 ▫ Blu-ray Headphones Operation . . . . . . . . . . . .413 ▫ Disc Formats . . . . . . . . . . . . . . . . . . . . . . . . .422 ▫ Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .414 ▫ Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 ▫ Replacing The Headphone Batteries. . . . . . . . .415 ▫ Product Agreement . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 311 ▫ Rear Manual Climate Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .443 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .446 ▫ Summer Operation . . . . . . . . . . . . . . . . . . . .458 ▫ Winter Operation. . . . . . . . . . . . . . . . . . . . . .458 ▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . .458 ▫ Window Fogging . . . . . . . . . . . . . . . . . . . . .
312 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Vents 2 — Instrument Cluster 3 — Shift Lever 4 — Radio 5 — Upper Glove Compartment 6 — Lower Glove Compartment 7 — Climate Controls 8 — DVD – If Equipped 9 — Storage Bin 10 — Cup Holders 13 — Hood Release 14 — Dimmer Switch 11 — Switch Bank 12 — Ignition Switch 15 — Headlight Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 313 INSTRUMENT CLUSTER — BASE 4
314 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 315 If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to 1. Tachometer alert you to turn the signal off. If either indicator flashes This gauge measures engine revolutions per minute at a rapid rate, check for a defective outside light bulb. (RPM x 1000). Before the pointer reaches the red area, 5. High Beam Indicator ease up on the accelerator to prevent engine damage.
316 UNDERSTANDING YOUR INSTRUMENT PANEL odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 NOTE: Some of the above warnings will be displayed in noFUSE the Electronic Vehicle Information Center Display Area If the vehicle diagnostic system determines that the located in the instrument cluster. Ignition Off Draw (IOD) fuse is improperly installed, or Refer to ”Electronic Vehicle Information Center (EVIC) damaged, a “noFUSE” message will display in the odometer display area. For further information on fuses and Display — If Equipped” for further information.
318 UNDERSTANDING YOUR INSTRUMENT PANEL Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the STEP button on the steering wheel. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following steps.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel 8.
320 UNDERSTANDING YOUR INSTRUMENT PANEL illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 9. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position, before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc.
322 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Electronic Stability Control (ESC) Activation/ NOTE: Malfunction Indicator Light — If Equipped • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on moThe “ESC Activation/Malfunction Indicator mentarily each time the ignition switch is turned to Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN. ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 11. Electronic Stability Control (ESC) OFF Indicator 14. Fuel Gauge Light — If Equipped The pointer shows the level of fuel in the fuel tank when This light indicates the Electronic Stability Con- the ignition switch is in the ON/RUN position. trol (ESC) is off. 15. Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on Indicates vehicle speed.
324 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. NOTE: • You must apply the brakes before shifting from PARK. 17. Vehicle Security Light — If Equipped This light will flash at a fast rate for approximately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 18.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
326 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is 20. Temperature Gauge applied with the ignition switch in the ON/RUN posi- The temperature gauge shows engine coolant temperation. ture. Any reading within the normal range indicates that NOTE: This light shows only that the parking brake is the engine cooling system is operating satisfactorily. applied. It does not show the degree of brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 WARNING! 22. Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
328 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 If the light remains lit with the engine running, your If the overheating continues, it may become necessary to vehicle will usually be drivable; however, see an autho- stop the vehicle and run the engine at idle with the rized dealer for service as soon as possible. If the light is transmission in NEUTRAL until the light turns off.
330 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches The Electronic Vehicle Information Center (EVIC) fea- mounted on the steering wheel. The EVIC consists of the tures a driver-interactive display that is located in the following: instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 The system allows the driver to select information by UP Button pressing the following buttons mounted on the steering Press and release the UP button to scroll upwheel: ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub-menus. DOWN Button Press and release the DOWN button to scroll downward through the main menus and sub-menus.
332 UNDERSTANDING YOUR INSTRUMENT PANEL The main display area will normally display the main menu or the screens of a selected feature of the main Press the BACK button to scroll back to a menu. The main display area also displays ⬙pop up⬙ previous menu or sub-menu. messages that consist of approximately 60 possible warning or information messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 • Unstored Messages This message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are ⬙Turn Signal On⬙ (if a turn signal is left on) and ⬙Lights On⬙ (if driver leaves the vehicle). When the appropriate conditions exist, the EVIC displays the following messages: • Unstored Messages Until RUN These messages deal primarily with the Remote Start feature.
334 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Not in Park • LOW WASHER FLUID • Press Brake Pedal and Push Button to Start • Oil Change Required • Door(s) Ajar (with a single chime, if vehicle is in • motion) • • Liftgate Ajar (chime will sound when vehicle starts • moving) • • Low Tire Pressure • • Service TPM System (refer to “Tire Pressure Monitoring System” in “Starting And Operating”) • • Tire Pressure Screen With Low Tire(s) “Inflate Tire to XX” • Turn Signal On • RKE Battery Low Left Front T
UNDERSTANDING YOUR INSTRUMENT PANEL 335 • Blind Spot System Not Available — This message is displayed to indicate the Blind Spot Monitor (BSM) system is temporarily unavailable due to sensor blockage, electronic interference, or other ⬙temporary⬙ conditions. When this message is displayed both outside rear view icons will be illuminated. If electronic interference is present, the BSM system will illuminate the icon only on the side of interference as long as interference is present.
336 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Speed Control SET • Loose Gascap Indicator If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the telltale display area. Tighten the fuel filler cap properly and press the SELECT button EVIC Amber Telltale Lights to turn off the message.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Do not operate the vehicle until the cause is corrected. This area will show reconfigurable red telltales. These This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. telltales include: • Charging System Light • Door Ajar EVIC Red Telltale Lights This light will turn on to indicate that one or more doors may be ajar. • Oil Pressure Warning Light This light indicates low engine oil pressure.
338 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Throttle Control (ETC) Light • Engine Temperature Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. This light warns of an overheated engine condition.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 • Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into NEUTRAL and run the engine at idle or faster until the light turns off.
340 UNDERSTANDING YOUR INSTRUMENT PANEL Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Menu button. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following steps. Fuel Economy Press and release the UP or DOWN button until “Fuel Economy” displays highlighted in the EVIC and press the SELECT button.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL” message. This display will continue until the vehicle runs out of fuel.
342 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Speed Trip A Press and release the UP or DOWN button until “Vehicle Speed” displays highlighted in the EVIC and press the SELECT button. Press the SELECT button to display the current speed in mph or km/h. Pressing the SELECT button a second time will toggle the unit of measure between mph or km/h. Shows the total distance traveled for Trip A since the last reset. Trip B Shows the total distance traveled for Trip B since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 Tire PSI Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “Tire PSI:” displays highlighted in the EVIC. Press the SELECT button to view a graphic of the vehicle with a tire pressure value at each corner of the graphic. Press and release the UP or DOWN button until “Vehicle Info” displays in the EVIC and press the SELECT button.
344 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The system will display the last known outside temperature when starting the vehicle and may need to Select from Main Menu using the UP or DOWN buttons. be driven several minutes before the updated temperaThis feature shows the number of stored warning mesture is displayed. Engine temperature can also affect the sages (in the # place holder).
UNDERSTANDING YOUR INSTRUMENT PANEL 345 Manual Compass Calibration Compass Variance If the compass appears erratic and the CAL indicator Compass Variance is the difference between Magnetic does not appear in the EVIC display, you must put the North and Geographic North. To compensate for the compass into the Calibration Mode manually, as follows: differences the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly 1. Turn ON the ignition switch.
346 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button. The last variance zone number displays in the EVIC. 4. Press and release the SELECT button until the proper variance zone is selected, according to the map. 5. Press and release the RETURN button to exit. Customer-Programmable Features (System Setup) Personal Settings allows you to set and recall features when the transmission is in PARK.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 Press and release the UP or DOWN button until ⬙System Setup⬙ is highlighted in the main menu of the EVIC. Then press the SELECT button to enter the System Setup sub-menu. Press and release the UP or DOWN button to select a feature form the following choices: Select Language When in this display you may select one of five languages for all display nomenclature, including the trip functions and the navigation system (if equipped).
348 UNDERSTANDING YOUR INSTRUMENT PANEL Refer to “Rear Park Assist System” in “Understanding the doors will unlock on the first press of the RKE The Features Of Your Vehicle” for system function and transmitter UNLOCK button. To make your selection, press and release the SELECT button until a check-mark operating information.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 and release the SELECT button until a check-mark appears next to the feature showing the system has been When this feature is selected and the remote start is activated or the check-mark is removed showing the activated, the heated steering wheel and driver heated system has been deactivated. seat features will automatically turn on in cold weather.
350 UNDERSTANDING YOUR INSTRUMENT PANEL a check-mark appears next to the feature showing the your selection, press and release the SELECT button until system has been activated or the check-mark is removed a check-mark appears next to the setting, showing that the setting has been selected. showing the system has been deactivated. Headlamp Off Delay When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing When ON is selected, the system will automatically that the setting has been selected. activate the windshield wipers if it senses moisture on the windshield.
352 UNDERSTANDING YOUR INSTRUMENT PANEL next to the feature showing the system has been activated Tilt Mirror In Reverse – If Equipped or the check-mark is removed showing the system has When this feature is selected and the vehicle is placed in been deactivated. a reverse gear, the driver’s side mirror will tilt downward to allow the driver to see into the previous blind spot and Easy Entry/Exit Seat – If Equipped avoid objects in close proximity to the rear of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 mode, in this mode the Blind Spot Monitor (BSM) will show a visual alert in the outside mirrors as well as an audible alert when the turn signal is on. When “Blind Spot Alert Off” is selected the Blind Spot Monitor (BSM) system is deactivated. Compass Variance Refer to “Compass Display” for more information. Turn Menu Off Press and release SELECT to turn the menu off.
354 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 130 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 TIME Button RW/FF Press the TIME button to alternate display of the time Pressing the RW (Rewind) or FF (Fast Forward) buttons and radio frequency. causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either Clock Setting Procedure AM or FM frequencies. 1. Press and hold the TIME button until the hours blink. TUNE Control 2.
356 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third AM/FM Button time and TREBLE will display. Turn the TUNE/SCROLL Press the buttons to select either AM or FM mode. control knob to the right or left to increase or decrease the SET/RND Button — To Set the Pushbutton Memory treble tones. When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 and 12 FM stations to be stored into pushbutton memory. Operation Instructions — CD MODE For CD And The stations stored in SET 2 memory can be selected by MP3 Audio Play pressing the pushbutton twice. NOTE: Every time a preset button is used, a corresponding • The ignition switch must be in the ON or ACC position button number will display. to operate the radio.
358 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 SEEK Button AM/FM Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. Press the button to select either AM or FM mode.
360 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.
362 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Uconnect® 130 WITH SATELLITE RADIO Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
364 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. Voice Command System (Radio) — If Equipped Refer to “Voice Command” for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button until the hours blink. procedure, starting at Step 2. 2. Adjust the hours by turning the right side TUNE/ INFO Button SCROLL control knob. Press the INFO button for an RDS station (one with call 3. After adjusting the hours, press the right side TUNE/ letters displayed).
366 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display. Turn the TUNE/SCROLL control knob to the front and rear speakers. the right or left to increase or decrease the bass tones.
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Program Type Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Wea
368 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is AM/FM Button displayed, the radio will be tuned to the next frequency Press the button to select either AM or FM mode. station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 369 and 12 FM stations to be stored into pushbutton memory. Operation Instructions — CD MODE for CD and The stations stored in SET 2 memory can be selected by MP3 Audio Play pressing the pushbutton twice. NOTE: Every time a preset button is used, a corresponding • The ignition switch must be in the ON/RUN or ACC button number will display. position to operate the radio.
370 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON/RUN and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 SEEK Button AM/FM Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. Press the button to select either AM or FM mode.
372 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 373 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.
374 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium single-session disc, enable the “Disc at Once” option before writing to the disc. contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 INFO Button (CD Mode for MP3 Play) Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected. Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available). device’s volume set to the proper level.
376 UNDERSTANDING YOUR INSTRUMENT PANEL sports, news, entertainment, and programming for chil- Electronic Serial Number/Sirius Identification dren, directly from its satellites and broadcasting studios. Number (ESN/SID) NOTE: Sirius service is not available in Hawaii and has Please have the following information available when calling: limited coverage in Alaska.
UNDERSTANDING YOUR INSTRUMENT PANEL 377 Selecting Uconnect® (Satellite) Mode Reception Quality Press the SAT button until ⬙SAT⬙ appears in the display. A Satellite reception may be interrupted due to one of the CD may remain in the radio while in the Satellite radio following reasons: mode. • The vehicle is parked in an underground parking Satellite Antenna structure or under a physical obstacle.
378 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Uconnect® (Satellite) Mode INFO Button SCAN Button TUNE Control (Rotary) Pressing the INFO button will cycle the display informaNOTE: The ignition switch must be in the ON/RUN or tion between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 379 MUSIC TYPE Button SETUP Button Pressing this button once will turn on the Music Type Pressing the SETUP button allows you to select the mode for five seconds. Pressing the MUSIC TYPE button following items: or turning the TUNE/SCROLL control knob within five • Display Sirius ID number — Press the AUDIO/ seconds will allow the program format type to be seSELECT button to display the Sirius ID number. This lected.
380 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 381 iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features. Please visit Apple’s website for software updates. Connecting The iPod® Or External USB Device Use the connection cable to connect an iPod® or external USB device to the vehicle’s USB connector port which is located in the glove compartment.
382 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The glove compartment will have a position where the iPod® or consumer electronic audio device cable can be routed through without damaging the cable when closing the lid. This allows routing of the cable without damaging it while closing the lid. If a cut out is not available in the glove compartment, route the cable away from the lid latch and in a place that will allow the lid to close without damaging the cable.
UNDERSTANDING YOUR INSTRUMENT PANEL 383 Controlling The iPod® Or External USB Device Using Radio Buttons • Turning it clockwise (forward) by one click, while playing a track, skips to the next track or press the VR button and say ⬙Next Track⬙.
384 UNDERSTANDING YOUR INSTRUMENT PANEL • Use the << SEEK and SEEK>> buttons to jump to the • Press the SCAN button to use iPod®/USB/MP3 deprevious or next track. Pressing the SEEK>> button vice scan mode, which will play the first 10 seconds of each track in the current list and then forward to the during play mode will jump to the next track in the next song.
UNDERSTANDING YOUR INSTRUMENT PANEL 385 List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode. List mode enables scrolling through the list of menus and tracks on the audio device. • TUNE control knob: The TUNE control knob functions in a similar manner as the scroll wheel on the audio device or external USB device.
386 UNDERSTANDING YOUR INSTRUMENT PANEL • LIST button: The LIST button will display the top level menu of the iPod® or external USB device. Turn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob. This will display the next sub-menu list item on the audio device, then follow the same steps to go to the desired track in that list. Not all iPod® or external USB device sub-menu levels are available on this system.
UNDERSTANDING YOUR INSTRUMENT PANEL 387 Bluetooth Streaming Audio (BTSA) Selecting A Different Audio Device Music can be streamed from your cellular phone to the 1. Press the PHONE button to begin. Uconnect® phone system. 2. After the ⬙Ready⬙ prompt and following the beep, say Controlling BTSA Using Radio Buttons ⬙Setup⬙, then say ⬙Select Audio Devices⬙. To enter BTSA mode, press either “AUX” button on the 3.
388 UNDERSTANDING YOUR INSTRUMENT PANEL Browse Browsing is not available on a Bluetooth Streaming Audio (BTSA) device. Only the current song that is playing will display info. UCONNECT® MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES™) — If Equipped Getting Started • Screen(s) located in the overhead console: Unfold the overhead LCD screen(s) by pushing the button on the overhead console behind the screen(s). Video Entertainment System (VES™) • Cycle the ignition to the ON or ACC position.
UNDERSTANDING YOUR INSTRUMENT PANEL 389 • Turn on the Player (if equipped on Dual Screen Sys- Blu-ray Player tem) by pushing the Power button, located on the far Play A Blu-ray Disc left, or by pressing the button on the Remote Control. To view a Blu-ray insert the disc into the Blu-ray VES™ • When the Video Screen(s) are open and a DVD/Blu- disc Player. Playback will begin automatically after the ray Disc is inserted into the VES™ player, the screen(s) Blu-ray is recognized by the disc drive.
390 UNDERSTANDING YOUR INSTRUMENT PANEL Using the Remote Control • Select an audio channel (Channel 1 for 2nd row screen and Channel 2 for 3rd row screen), then press the source key and select VES™ Disc from the menu. • Press popup/menu key to navigate disc menu and options. NOTE: Due to the size of the content on a Blu-ray disc, the disc may not start playing immediately. Play Video Games Connect the video game console to the Auxiliary RCA input jacks or HDMI port, located on the left side behind 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 391 When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: NOTE: Certain high-end video games, such as Playstation3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter. Refer to the Power Inverter section in your vehicle’s Owner’s Manual for more information. Using The Remote Control 1. Press the MODE button on the Remote Control. Select VES AUX1 Mode On The VES Screen 2.
392 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the Rear VES soft-key to display the Rear VES 3. Touch the 1 soft-key and then touch either AUX 1 or Controls. If a channel list is displayed, press the HIDE AUX 2 in the VES column (depending which AUX LIST soft-key to display the Rear VES Controls screen. input is used). To exit press the back arrow soft-key at the top of the screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 393 Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 Ensure the Remote Control and Headphone switch is on Channel 2. Using The Remote Control 1. Press the SOURCE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen. 2.
394 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the Rear VES soft-key to display the Rear VES 3. To listen to an audio source on Channel 2 while a Controls. If a channel list is displayed, press the HIDE video is playing on Channel 1, touch the 2 soft-key and LIST soft-key to display the Rear VES Controls screen. choose an audio source. To exit touch the back arrow soft-key at the top left of the left screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 395 3. To watch a DVD on Screen 1 for second row passengers, ensure the Remote Control and Headphone NOTE: Typically there are two different ways to operate switch is on Channel 1. the features of the Video Entertainment System (VES™). 4. To watch a DVD on Screen 2 for third row passengers, • The Remote Control ensure the Remote Control and Headphone switch is on Channel 2.
396 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. • Channel/Screen 2 select mode information is shown on the right side of the screen. • The VES™ will retain the last setting when turned off. Using The Touch-Screen Radio Controls 1. Press the MENU hard-key on the radio faceplate. Select DISC Mode On The VES™ Screen 2. Touch the Rear VES soft-key to display the Rear VES Controls.
UNDERSTANDING YOUR INSTRUMENT PANEL 397 NOTE: • To view a DVD on the radio press the RADIO/MEDIA hard-key, on the radio faceplate, then touch the DISC tab soft-key and then the VIEW VIDEO soft-key. • Viewing a DVD on the Touch-Screen radio screen is not available in all states/provinces. If available, the vehicle must be stopped and the shift lever must be in the PARK position for vehicles with an automatic transmission. In vehicles with a manual transmission the parking brake must be engaged.
398 UNDERSTANDING YOUR INSTRUMENT PANEL Play A DVD Using The VES™ Player (If Equipped) Using The Remote Control 1. Insert the DVD with the label facing up. The VES™ 1. Press the SOURCE button on the Remote Control. player automatically selects the appropriate mode 2. While looking at Screen 1 or 2, highlight VES DISC by after the disc is recognized and starts playing the either pressing Up/Down/Left/Right buttons or by DVD. repeatedly pressing the SOURCE button, then press ENTER/OK on the Remote Control.
UNDERSTANDING YOUR INSTRUMENT PANEL 399 NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. • Channel/Screen 2 select mode information is shown on the right side of the screen. • The VES™ will retain the last setting when turned off. Using The Touch-Screen Radio Controls 1. Press the MENU hard-key on the radio faceplate. Rear VES Soft-key 2. Touch the Rear VES soft-key to display the Rear VES Controls. If a channel list is displayed, touch the HIDE 3.
400 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • To view a DVD on the radio press the RADIO/MEDIA hard-key, on the radio faceplate, then touch the DISC tab soft-key and then the VIEW VIDEO soft-key. • Viewing a DVD on the Touch-Screen radio screen is not available in all states/provinces. If available, the vehicle must be stopped and the shift lever must be in the PARK position for vehicles with an automatic transmission. In vehicles with a manual transmission the parking brake must be engaged.
UNDERSTANDING YOUR INSTRUMENT PANEL 401 Play A Blu-ray Disc Using The Blu-ray Player (If Equipped) Using The Remote Control 1. Press the SOURCE button on the Blu-ray player Re1. Insert the Blu-ray disc with the label facing up. The mote Control. Blu-ray player automatically selects the appropriate 2. While looking at Screen 1 or 2, highlight Blu-ray by mode after the disc is recognized and starts playing either pressing Up/Down/Left/Right buttons or by the Blu-ray disc.
402 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls NOTE: • To view a Blu-ray Disc on the radio press the RADIO/ MEDIA hard-key, on the radio faceplate, then touch 2. Touch the Rear VES™ soft-key to display the Rear the VES™ Disc tab soft-key and then the VIEW VIDEO VES™ Controls. If a channel list is displayed, touch soft-key. the HIDE LIST soft-key to display the Rear VES™ Controls screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 403 Listen To An Audio Source While A Video Is Playing Ensure the Remote Control and Headphone switch are on the same channel. If watching a video on Screen 1 (second row), then Channel 2 could be used for audio. If watching a video on Screen 2 (third row), then Channel 1 could be used for audio. 4 Using The Remote Control 1.
404 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the Rear VES soft-key to display the Rear VES 3. To listen to an audio source on Channel 2 while a Controls. If a channel list is displayed, press the HIDE video is playing on Channel 1, touch the 2 soft-key and LIST soft-key to display the Rear VES Controls screen. choose an audio source. To exit touch the back arrow soft-key at the top left of the left screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 405 • Selecting a video source on Channel 2, the video source will display on the third row screen or Screen 2 • VES is able to transmit two channels of stereo audio and can be heard on Channel 2. and video simultaneously. • The 2nd row screen and 3rd row screen of the Video • The Blu-ray Disc Player can play CDs, DVDs and Entertainment System can play two separate discs by Blu-ray Discs.
406 UNDERSTANDING YOUR INSTRUMENT PANEL VES™ Remote Control – If Equipped 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. Light – Turns the remote control backlighting on or off. The remote backlighting turns off automatically after five seconds. Remote Control Controls And Indicators 4. Channel/Screen Selector Switch - Indicates which channel is being controlled by the remote control.
UNDERSTANDING YOUR INSTRUMENT PANEL 407 6. 䉲 / Prev – In radio modes, press to select to the 10. PROG Up/Down / Rewind/skip back and fast fwd/ previous station. In disc modes, press to advance to skip forward – When listening to a radio mode, the start of the current or previous audio track or pressing PROG Up selects the next preset and pressvideo chapter. In menu modes, use to navigate in the ing PROG Down selects the previous preset stored in menu. the radio.
408 UNDERSTANDING YOUR INSTRUMENT PANEL 12. SLOW – If Equipped – Press to slow playback of a 16. BACK – When navigating in menu mode, press to DVD disc. Press play (䉴) to resume normal play. return to the previous screen. When navigating a DVDs disc menu, the operation depends on the disc’s 13. STATUS – If Equipped – Press to display the current contents. status. 17. 䉳䉳 – In radio modes, press to seek to the previous 14. MODE/SOURCE – Press to change the mode of the tunable station.
UNDERSTANDING YOUR INSTRUMENT PANEL 409 Blu-ray Player Remote Control – If Equipped 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. SOURCE – Press to enter Source Selection screen. 4. Channel/Screen Selector Switch - Indicates which channel is being controlled by the remote control. When the selector switch is in the Rear 1 position, the remote controls the functionality of headphone Channel 1 (second row).
410 UNDERSTANDING YOUR INSTRUMENT PANEL 7. 䉴䉴 – Press and release to jump to the next available 13. 䉳䉳 – Press and release to jump to the previous audio track or video chapter. Press and hold to fast audio track or video chapter. Press and hold to fast forward through the current audio track or video rewind through the current audio track or video chapter. chapter. 8. 䉴 / 㥋 (Play/Pause) – Begin/resume or pause disc play. 14. MUTE – Mutes headphone audio. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL 411 Remote Control Storage The video screen(s) come with a built in storage compartment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be very difficult to remove.
412 UNDERSTANDING YOUR INSTRUMENT PANEL Locking The Remote Control All remote control functionality can be disabled as a parental control feature. • To disable the Remote Control from making any changes, press the Video Lock button on the DVD player (if equipped). If the vehicle is not equipped with a DVD player, follow the radio’s instructions to turn Video Lock on. The radio and the video screen(s) indicate when Video Lock is active.
UNDERSTANDING YOUR INSTRUMENT PANEL 413 Blu-ray Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for themselves. 1. 2. 3. 4.
414 UNDERSTANDING YOUR INSTRUMENT PANEL Controls The headphone power indicator and controls are located on the right ear cup. NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off. Changing the Audio Mode for Headphones 1. Power Button 2. Volume Control 3. Channel Selection Switch 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 415 4. When the Mode Selection menu appears on screen, use the cursor buttons on the remote control to navi• When both switches are on Channel 1, the Remote is gate to the available modes and press the OK button to controlling Channel 1 and the headphones are tuned to select the new mode. the audio of the VES™ Channel 1. 5. To cancel out of the Mode Selection menu, press the • When both switches are on Channel 2, the Remote is BACK button on the remote control.
416 UNDERSTANDING YOUR INSTRUMENT PANEL Unwired® Stereo Headphone Lifetime Limited Warranty Who Does This Warranty Cover? This warranty covers the initial user or purchaser (⬙you⬙ or ⬙your⬙) of this particular Unwired Technology LLC (⬙Unwired⬙) wireless headphone (⬙Product⬙). The warranty is not transferable. How Long Does the Coverage Last? This warranty lasts as long as you own the Product.
UNDERSTANDING YOUR INSTRUMENT PANEL 417 What Will Unwired® Do? Unwired®, at its option, will repair or replace any defective Product. Unwired® reserves the right to replace any discontinued Product with a comparable model. THIS WARRANTY IS THE SOLE WARRANTY FOR THIS PRODUCT, SETS FORTH YOUR EXCLUSIVE REMEDY REGARDING DEFECTIVE PRODUCTS, AND IS IN LIEU OF ALL OTHER WARRANTIES (EXPRESS OR IMPLIED), INCLUDING ANY WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
418 UNDERSTANDING YOUR INSTRUMENT PANEL The VES™ has the ability to switch tuner (AM/FM), Information Mode Display SEEK, SCAN, TUNE, and recall presets in radio modes as long as it is not in shared mode. When in shared disc mode both the radio and the VES™ have control of the video functions. The VES™ has the ability to control the following video modes: 1. CD: Ability to Fast Forward, Rewind, Scan, and Track Up/Down. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 419 4. Channel 2 Mode Numeric Keypad Menu 5. Channel 2 Shared Status 6. Channel 2 Audio Only/Mute 7. Channel 1 ENTER/OK Button Action 8. Channel 2 ENTER/OK Button Action 4 9. Clock 10. Video Lock 11. Not Available / Error Numeric Keypad Menu When the display for either Channel 1 or Channel 2 shows DIRECT TUNE, pressing the remote control’s OK button activates a numeric keypad menu.
420 UNDERSTANDING YOUR INSTRUMENT PANEL makes it easy to enter a specific tuner frequency, satellite Station List Menu channel, or track number. To enter the desired digit: When listening to Satellite audio, pressing the remote 1. Press the remote control’s navigation buttons (䉱, 䉲, control’s POP UP/MENU button displays a list of all available channels. Navigate this list using the remote 䉴, 䉳) to navigate to the desired digit. control’s navigation buttons (䉱, 䉲) to find the desired 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 421 Disc Menu Display Settings When watching a video source (DVD Video with the disc in Play mode, Aux Video, etc.), pressing the remote control’s SETUP button activates the Display Settings menu. These settings control the appearance of the video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change these settings under normal circumstances.
422 UNDERSTANDING YOUR INSTRUMENT PANEL Listening To Audio With The Screen Closed Disc Formats To listen to only audio portion of the channel with the The VES™ DVD player is capable of playing the followscreen closed: ing types of discs (12 cm or 8 cm diameter): • Set the audio to the desired source and channel. • Close the video screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 423 The Blu-Ray player is capable of the playing the follow- DVD Audio Support ing types of discs (12 cm diameter): When a DVD-Audio disc is inserted in the VES™ DVD player, the DVD-Audio title on the disc is played by • BD: BDMV (Profile 1.1), BDAV (Profile 1.1), default (most DVD-Audio discs also have a Video title, • DVD: DVD-Video, DVD-Audio, AVCREC, AVCHD, but the Video title is ignored).
424 UNDERSTANDING YOUR INSTRUMENT PANEL If you record a disc using a personal computer, there may • The player recognizes a maximum of 512 files and 99 be cases where the VES™ DVD player may not be able to folders per CD-R and CD-RW disc. play some or the entire disc, even if it is recorded in a • Mixed media recordable DVD formats will only play compatible format and is playable on other players. To the Video_TS portion of the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 425 • Other compression formats such as AAC, MP3 Pro, Ogg Vorbis, and ATRAC3 will not play. The DVD The DVD player is capable of playing MP3 (MPEG-1 player will automatically skip the file and begin playAudio Layer 3) and WMA (Windows Media Audio) files ing the next available file. from a CD Data disc (usually a CD-R or CD-RW).
426 UNDERSTANDING YOUR INSTRUMENT PANEL The DVD player may shut down during extremely hot conditions, such as when the vehicle’s interior temperaIf the DVD player is unable to read the disc, a ⬙Disc Error⬙ ture is above 120°F. When this occurs, the DVD player message is displayed on the VES™ and Radio displays will display ⬙VES High Temp⬙ and will shut off the VES™ and the disc is automatically ejected. A dirty, damaged, or displays until a safe temperature is reached.
UNDERSTANDING YOUR INSTRUMENT PANEL 427 Display Other Language Setup All of the Language settings have a special ⬙Other⬙ setting to accommodate languages other than Japanese or English. These languages are selected using a special fourdigit code. To enter a new language code, activate the DVD Setup Menu.
428 UNDERSTANDING YOUR INSTRUMENT PANEL • Using the remote control Up and Down cursor buttons, select a digit for the current position. After selecting the digit, press the remote control’s Right cursor button to select the next digit. Repeat this digit selection sequence for all four digits. Rating and Password Setup The Rating and Password settings work together to control the types of DVDs that your family watches.
UNDERSTANDING YOUR INSTRUMENT PANEL 429 Not all DVD discs encode a Rating, so it is still possible that discs designed for adult audiences can still play without requiring a password. The default rating is Level 8 (play all discs without a password) and the default password is 0000.
430 UNDERSTANDING YOUR INSTRUMENT PANEL To set the password, activate the DVD Setup Menu and • After the four-digit password is entered, press the follow these additional instructions: remote control’s ENTER/OK button. If the password is correct, the set password screen is displayed. • Using the remote control Left and Right cursor but• Using the remote control’s Up and Down cursor tons, select the Rating tab.
UNDERSTANDING YOUR INSTRUMENT PANEL 431 To set the rating, activate the DVD Setup Menu and follow these additional instructions: • Using the remote control’s Left and Right cursor buttons, select the Rating tab. • Highlight ⬙Change Rating⬙, and then press the remote control’s ENTER/OK button. • Enter the current password.
432 UNDERSTANDING YOUR INSTRUMENT PANEL Product Agreement Software This product contains software licensed under GNU General Public License (GPL) or GNU Lesser General Public License (LGPL), etc. You have the right of acquisition, modification, and distribution of the source code of the GPL/LGPL software. You may download Source Code from the following website at no charge. URL: http://www.embedded-carmultimedia.
UNDERSTANDING YOUR INSTRUMENT PANEL 433 AND/OR (ii) DECODE VC-1 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM Patents Cinavia Notice Center at http://www.cinavia.com.
434 UNDERSTANDING YOUR INSTRUMENT PANEL • Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol and DTS 2.0 Channel are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved. your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
UNDERSTANDING YOUR INSTRUMENT PANEL 435 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel, at the three and nine o’clock positions. The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume.
436 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation CD/DVD/BLU-RAY DISC MAINTENANCE Pressing the top of the switch will SEEK up for the next To keep a CD/DVD/Blu-ray disc in good condition, take listenable station, and pressing the bottom of the switch the following precautions: will SEEK down for the next listenable station. 1. Handle the disc by its edge; avoid touching the The button located in the center of the left-hand switch surface. will tune to the next preset station that you have pro2.
UNDERSTANDING YOUR INSTRUMENT PANEL 437 NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. CLIMATE CONTROLS The Climate Control system allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle.
438 UNDERSTANDING YOUR INSTRUMENT PANEL When the front control is in any position other than rear, the front control operates all the rear functions. The rear airflow modes will mirror the front unit operation. Rear Panel mode is automatically selected when the front control is in the Panel mode. When the front unit is in Bi-Level mode, airflow will be emitted from both the upper and lower rear outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 439 2. Rear Blower Control — If Equipped NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position. Blower control should be left in the ⬙ON⬙ position to allow the climate control to either warm or cool the vehicle. • Use this control to regulate the amount of air forced through the rear system in any mode you select.
440 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Mix Mode 8. Electronic Rear Window Defrost Air is directed through the floor, defrost and side Press this button to turn on the rear window defroster and the heated outside mirrors (if window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the equipped). An indicator in the button will illuminate windshield. This setting is good for maintaining comfort, when the rear window defroster is on.
UNDERSTANDING YOUR INSTRUMENT PANEL 441 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
442 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. For maximum defogging, select the outside air position. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects.
UNDERSTANDING YOUR INSTRUMENT PANEL 443 NOTE: There is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. 13. Panel Mode Button Rotate the temperature control knob to the desired temperature. Also, make sure to select only Panel, Bi-Level or Floor modes.
444 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control The primary control for the rear blower is on the front climate control unit, located on the instrument panel. Only when the front control for the rear blower is in the REAR position do the second row seat occupants have control of the rear blower speed. The rear blower control, located in the rear overhead console, has an off position and a range of blower speeds.
UNDERSTANDING YOUR INSTRUMENT PANEL 445 CAUTION! (Continued) just behind the sliding door. Do not block or place objects directly in front of the inlet grille or heater outlets. The electrical system could overload, causing damage to the blower motor. Rear Temperature Control The rear mode selection REAR, allows the settings to be controlled by the rear mode control knob. Rear Mode Control Headliner Mode Air comes from the outlets in the headliner.
446 UNDERSTANDING YOUR INSTRUMENT PANEL The Three-Zone ATC system automatically maintains the interior comfort level desired by the driver and all passengers. The system automatically adjusts the air temperature, • Front Three-Zone ATC allows both driver and front the airflow volume, amount of outside air recirculation and passenger seat occupant, and rear seat occupants to the airflow direction. This maintains a comfortable temselect individual comfort settings. perature, even under changing conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 447 1. Air Conditioning (A/C) Button 6. Auto Indicator Press and release to change the current Air Conditioning This indicates when the system is in Auto mode. (A/C) setting, the indicator illuminates when A/C is ON. 7. Right Front Seat Occupant Temperature Display Performing this function will cause the ATC to switch This display shows the temperature setting for the right into manual mode. front seat occupant. 2. Left Front Seat Occupant Temperature Display 8.
448 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Rear Control Button 13. Climate Control OFF Button Provides toggle operation between front control screen Press and release to turn the Climate Control OFF. If the and rear control screen. Push the button to activate the control is OFF, press any button to turn the control ON. rear climate control screen and allow the front seat 14. Blower Control occupants control over the rear climate settings. There are seven blower speeds, the blower speed in11.
UNDERSTANDING YOUR INSTRUMENT PANEL 449 16. Recirculation Control Button Automatic Operation Press and release to change the current setting, the 1. Press the AUTO button on the front ATC Panel and the words Front Auto will illuminate in the front ATC indicator illuminates when ON. display, along with two temperatures for the driver 17. SYNC Button and front passenger. The system will then automatiPress and release to control the temperature setting for all cally regulate the amount of airflow.
450 UNDERSTANDING YOUR INSTRUMENT PANEL 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. NOTE: To provide you with maximum comfort in the automatic mode, during cold start-ups, the blower fan will remain on low until the engine warms up.
UNDERSTANDING YOUR INSTRUMENT PANEL 451 • Air Conditioning (A/C) Controlling The Rear Climate Controls From The Front ATC Panel The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning The Three-Zone ATC system allows for adjustment of the system. When in A/C mode and the ATC is set to a cool rear climate controls from the front ATC panel. temperature, dehumidified air flows through the air To change the rear system settings: outlets.
452 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Mode Display This display shows the current Mode selection. 2. Rear Temperature Display This display shows the temperature setting for the rear seat occupants. 3. Blower Control Display This display shows the current Blower speed selection. 4. Rear Auto Indicator This indicates when the system is in Rear Auto mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 453 Rear Mode Control Headliner Mode Rear Automatic Temperature Control (ATC) — If Equipped The rear ATC system has floor air outlets at the rear of the Air comes from the outlets in the headliner. Each right side sliding door, and overhead outlets at each of these outlets can be individually adjusted to outboard rear seating position. The system provides heated direct the flow of air.
454 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Press the Rear Temperature Lock button on the front ATC panel. This turns off the Rear Temperature Lock icon in the rear temperature knob. 2. Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs. 3. ATC is selected by adjusting the rear blower knob counterclockwise to AUTO.
UNDERSTANDING YOUR INSTRUMENT PANEL 455 NOTE: Rear Blower Control • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. The rear blower control knob can be manually set to off, or any fixed blower speed, by rotating the knob from low to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle.
456 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control Rear Mode Control To change the temperature in the rear of the vehicle, rotate the temperature knob counterclockwise to lower the temperature, and clockwise to increase the temperature. The rear temperature settings are displayed in the front ATC panel. • Auto Mode The rear system automatically maintains the correct mode and comfort level desired by the rear seat occupants.
UNDERSTANDING YOUR INSTRUMENT PANEL 457 • Bi-Level Mode Recirculation Control Air comes from both the headliner outlets and the When outside air contains smoke, odors, or high humidfloor outlets. ity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the RecirNOTE: In many temperature positions, the Bi-Level culation control button. Recirculation mode mode is designed to provide cooler air out of the headshould only be used temporarily.
458 UNDERSTANDING YOUR INSTRUMENT PANEL Procedures” in “Maintaining Your Vehicle” for proper coolant selection. Use of the air Recirculation mode The engine cooling system must be protected with a during Winter months is not recommended, because it high-quality antifreeze coolant to provide proper corromay cause window fogging. sion protection and to protect against engine overheating. A solution of 50% ethylene glycol antifreeze coolant and Vacation/Storage 50% water is recommended.
UNDERSTANDING YOUR INSTRUMENT PANEL 459 enter the plenum, they could plug the water drains. In Winter months, make sure the air intake is clear of ice, Vehicle windows tend to fog on the inside in mild, rainy slush, and snow. and/or humid weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. A/C Air Filter Do not use the Recirculation mode without A/C for long On vehicles equipped with Automatic Temperature Conperiods, as fogging may occur.
460 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .465 ▫ Brake/Transmission Shift Interlock System . . .471 ▫ Automatic Transmission . . . . . . . . . . . . . . . .465 ▫ Fuel Economy (ECON) Mode . . . . . . . . . . . . .471 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .465 ▫ Six-Speed Automatic Transmission . . . . . . . . .472 ▫ Extreme Cold Weather (Below –20°F Or −29°C) . . . . . . . . . . . . . . . . . . . . . . . . . .466 ▫ Gear Ranges . . . . .
462 STARTING AND OPERATING 䡵 POWER STEERING . . . . . . . . . . . . . . . . . . . . .485 ▫ Tire Identification Number (TIN). . . . . . . . . . .507 ▫ Power Steering Fluid Check . . . . . . . . . . . . . .486 ▫ Tire Terminology And Definitions . . . . . . . . . .509 䡵 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . .487 ▫ Tire Loading And Tire Pressure . . . . . . . . . . .510 䡵 ANTI-LOCK BRAKE SYSTEM (ABS) . . . . . . . . .489 䡵 TIRES — GENERAL INFORMATION . . . . . . . .
STARTING AND OPERATING 463 ▫ Compact Spare Tire – If Equipped . . . . . . . . .520 䡵 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . .537 ▫ Full Size Spare – If Equipped . . . . . . . . . . . . .520 ▫ 3.6L Engine . . . . . . . . . . . . . . . . . . . . . . . . . .537 ▫ Limited-Use Spare – If Equipped . . . . . . . . . .521 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .538 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .522 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . .
464 STARTING AND OPERATING ▫ Selection Of Engine Oil For Flexible Fuel 䡵 VEHICLE LOADING . . . . . . . . . . . . Vehicles (E-85) And Gasoline Vehicles . . . . . . .545 ▫ Vehicle Certification Label . . . . . . . ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .545 䡵 TRAILER TOWING . . . . . . . . . . . . . ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . .545 ▫ Common Towing Definitions . . . . . ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . .546 ▫ Towing Tips . . .
STARTING AND OPERATING 465 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.
466 STARTING AND OPERATING 3. If the engine fails to start, the starter will disengage If The Engine Fails To Start automatically in 10 seconds. If this occurs, turn the ignition switch to the OFF position, wait 10 to 15 WARNING! seconds, then repeat the “Normal Starting” procedure • Never pour fuel or other flammable liquids into (Steps 1–3 above). the throttle body air inlet opening in an attempt to NOTE: This vehicle is equipped with a transmission start the vehicle.
STARTING AND OPERATING 467 WARNING! (Continued) • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “Jump Starting” in “What To Do In Emergencies” for further information. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released.
468 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. The engine block heater cord is routed under the hood on the driver’s side of the vehicle.
STARTING AND OPERATING 469 WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
470 STARTING AND OPERATING WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
STARTING AND OPERATING 471 Brake/Transmission Shift Interlock System Fuel Economy (ECON) Mode This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the transmission shifter in PARK unless the brakes are applied. To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed. The Fuel Economy (ECON) mode can improve the vehicle’s overall fuel economy during normal driving conditions.
472 STARTING AND OPERATING When the Fuel Economy (ECON) Mode is engaged, the Six-Speed Automatic Transmission vehicle control systems will change the following: The transmission gear position display (located in the • The transmission will upshift sooner and downshift instrument cluster) indicates the transmission gear range. later.
STARTING AND OPERATING 473 The transmission shift lever has only PARK, REVERSE, NEUTRAL, and DRIVE shift positions. Manual downshifts can be made using the Electronic Range Select (ERS) shift control (described later in this section). Moving the shift lever to the left or right (–/+) while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
474 STARTING AND OPERATING PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake.
STARTING AND OPERATING 475 WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
476 STARTING AND OPERATING WARNING! (Continued) • Allowing children to be alone in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING 477 REVERSE This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL Use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into PARK if you must leave the vehicle. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.
478 STARTING AND OPERATING DRIVE This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, third, and fourth gears, direct fifth gear and overdrive sixth gear. The DRIVE position provides optimum driving characteristics under all normal operating conditions.
STARTING AND OPERATING 479 PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without damaging the transmission. NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur.
480 STARTING AND OPERATING You can switch between DRIVE and ERS mode at any To exit ERS mode, simply press and hold the shift lever to vehicle speed. When the shift lever is in the DRIVE the right (+) until “D” is once again displayed in the position, the transmission will operate automatically, instrument cluster. shifting between all available gears.
STARTING AND OPERATING 481 NOTE: To select the proper gear position for maximum deceleration (engine braking), tap the shift lever to the left (-) repeatedly as the vehicle slows. The transmission will shift to the range from which the vehicle can best be slowed down. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds.
482 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
STARTING AND OPERATING 483 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle. and Warning before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
484 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING 485 • Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. The standard power steering system will give you good This is due to the cold, thick fluid in the steering vehicle response and increased ease of maneuverability system. This noise should be considered normal, and it in tight spaces. The system will provide mechanical does not in any way damage the steering system. steering capability if power assist is lost.
486 STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
STARTING AND OPERATING 487 PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the PARK position. The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, press the park brake pedal a second time and let your foot up as you feel the brake disengage.
488 STARTING AND OPERATING NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING 489 CAUTION! If the Brake System Warning Light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. ANTI-LOCK BRAKE SYSTEM (ABS) ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
490 STARTING AND OPERATING WARNING! WARNING! (Continued) • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed, or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.
STARTING AND OPERATING 491 If the “Anti-Lock Brake Warning Light” is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the “Anti-Lock Brake The “Anti-Lock Brake Warning Light” monitors the anti-lock brake system. The light will Warning Light” does not come on when the ignition switch is turned to the ON position, have the bulb come on when the ignition switch is turned to repaired as soon as possible.
492 STARTING AND OPERATING system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel Your vehicle is equipped with an advanced electronic that is not spinning. This feature remains active even if brake control system that includes the Traction Control the ESC is in the “Partial Off” mode.
STARTING AND OPERATING 493 WARNING! (Continued) • The TCS cannot prevent collisions, including those resulting from excessive speed in turns, or hydroplaning. • The capabilities of a TCS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. Brake Assist System (BAS) The Brake Assist System (BAS) is designed to optimize the vehicle’s braking capability during emergency braking maneuvers.
494 STARTING AND OPERATING the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or The Electronic Stability Control (ESC) enhances directional control and stability of the vehicle under various understeer condition. driving conditions. ESC corrects for over/under steering • Oversteer - when the vehicle is turning more than of the vehicle by applying the brake of the appropriate appropriate for the steering wheel position.
STARTING AND OPERATING 495 WARNING! (Continued) resulting from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. ESC Operating Modes ESC On This mode is the normal operating mode for ESC on two-wheel drive vehicles.
496 STARTING AND OPERATING traction. To turn ESC on again, momentarily press the NOTE: To improve the vehicle’s traction when driving “ESC Off” switch. This will restore the normal “ESC On” with snow chains, or starting off in deep snow, sand or mode of operation. gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch.
STARTING AND OPERATING 497 light remains on after several ignition cycles, and the NOTE: vehicle has been driven several miles (kilometers) at • The “ESC Activation/Malfunction Indicator Light” speeds greater than 30 mph (48 km/h), see your authoand the “ESC OFF Indicator Light” come on momenrized dealer as soon as possible to have the problem tarily each time the ignition switch is turned ON. diagnosed and corrected.
498 STARTING AND OPERATING Malfunction Indicator Light” will flash, the engine power may be reduced and you may feel the brakes being TSC uses sensors in the vehicle to recognize an excesapplied to individual wheels to attempt to stop the trailer sively swaying trailer and will take the appropriate from swaying. TSC is disabled when the ESC system is in actions to attempt to stop the sway. The system may the “Partial Off” mode.
STARTING AND OPERATING 499 Hill Start Assist (HSA) HSA Activation Criteria The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill.
500 STARTING AND OPERATING HSA will work in REVERSE and all forward gears when “Electronic Vehicle Information Center (EVIC)” in “Unthe activation criteria have been met. The system will not derstanding Your Instrument Panel” for further informaactivate if the vehicle is placed in NEUTRAL or PARK. tion. WARNING! There may be situations on minor hills (i.e., less than 8%), with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur.
STARTING AND OPERATING 501 7. Press the “ESC Off” switch (located in the lower Towing With HSA switch bank below the climate controls) four times HSA will provide assistance when starting on a grade within 20 seconds. The “ESC Activation/Malfunction when pulling a trailer. Indicator Light” should turn on and turn off two times. WARNING! 8. Rotate the steering wheel back to center and then an additional half-turn to the right. 9.
502 STARTING AND OPERATING WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK and using the parking brake, it will roll down the hill and could cause a collision with another vehicle or object. Always remember to use the parking brake while parking on a hill, and that the driver is responsible for braking the vehicle.
STARTING AND OPERATING 503 NOTE: tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designation. Example: LT235/85R16. • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- • Temporary spare tires are spares designed for tempotion. Example: P215/65R15 95H. rary emergency use only.
504 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 505 EXAMPLE: R = Construction code — ⬙R⬙ means radial construction — ⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved und
506 STARTING AND OPERATING EXAMPLE: Load Identification: ⴖ....blank....
STARTING AND OPERATING 507 Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
508 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits) — 03 means the 3rd week 01 = Number representing the year in which the tire was manufactured (two digits) — 01 means the year 2001 — Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
STARTING AND OPERATING 509 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
510 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 511 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
512 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • The following table shows examples on how to calcu“XXX” amount equals 1,400 lbs (635 kg) and there will late total load, cargo/luggage, and towing capacities be five 150 lb (68 kg) passengers in your vehicle, the of your vehicle with varying seating configurations amount of available cargo and luggage load capacity and number and size of occupants.
STARTING AND OPERATING 513 5
514 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 515 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride.
516 STARTING AND OPERATING been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire At least once a month: inflation pressure must not exceed the maximum infla• Check and adjust tire pressure with a good quality tion pressure molded into the tire sidewall. pocket-type pressure gauge. Do not make a visual Check tire pressures more often if subject to a wide range judgement when determining proper inflation.
STARTING AND OPERATING 517 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures For High Speed Operation WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
518 STARTING AND OPERATING Tire Repair All Season Tires – If Equipped If your tire becomes damaged, it may be repaired if it All Season tires provide traction for all seasons (spring, summer, fall and winter). Traction levels may vary bemeets the following criteria: tween different all season tires. All season tires can be • The tire has not been driven on when flat, identified by the M+S, M&S, M/S or MS designation on • The damage is only on the tread section of your tire the tire sidewall.
STARTING AND OPERATING 519 While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be Some areas of the country require the use of snow tires poorer than that of non-studded tires. Some states produring the winter. Snow tires can be identified by a hibit studded tires; therefore, local laws should be mountain/snowflake symbol on the tire sidewall. checked before using these tire types.
520 STARTING AND OPERATING Compact Spare Tire – If Equipped The compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the Tire and Loading Information Placard located on the driver’s side door opening or on the sidewall of the tire. Compact spare tire descriptions begin with the letter “T” or “S” preceding the size designation. Example: T145/ 80D18 103M.
STARTING AND OPERATING 521 your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-Use Spare – If Equipped The limited-use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited-use spare wheel. This label contains the driving limitations for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
522 STARTING AND OPERATING Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced. ping when you are stuck. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information.
STARTING AND OPERATING 523 These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to replacement tires in this section for further information. Life Of Tire WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
524 STARTING AND OPERATING Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall. See the Tire Sizing Chart example found in the Tire Safety Information section of this manual for more information relating to the Load Index and Speed Symbol of a tire. It is recommended to replace the two front tires or two rear tires as a pair.
STARTING AND OPERATING 525 WARNING! (Continued) TIRE CHAINS (TRACTION DEVICES) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage: CAUTION! • Traction device must be of proper size for the tire, as recommended by the traction device manufacturer.
526 STARTING AND OPERATING WARNING! CAUTION! (Continued) Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used.
STARTING AND OPERATING 527 The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed. and braking functions. For these reasons, they wear at unequal rates. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
528 STARTING AND OPERATING The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning The TPMS will warn the driver of a low tire pressure threshold for any reason, including low temperature based on the cold inflation tire placard pressure requireeffects, or natural air pressure loss through the tire. ments found on the tire placard label located on the driver’s-side B-pillar.
STARTING AND OPERATING 529 For example, your vehicle may have a recommended cold (parked for more than three hours) tire placard pressure of 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 30 psi (207 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 26 psi (179 kPa). This tire pressure is sufficiently low enough to turn on the “Tire Pressure Monitoring Telltale Light.
530 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in • The TPMS is not intended to replace normal tire care the tire. and maintenance, or to provide warning of a tire Base System failure or condition. NOTE: • The TPMS should not be used as a tire pressure gauge The TPMS uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levwhile adjusting your tire pressure. els.
STARTING AND OPERATING 531 Tire Pressure Monitoring Low Tire Pressure Warnings NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, a “LOW TIRE PRESSURE” message will display in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low.
532 STARTING AND OPERATING 3. Accumulation of excessive snow and/or ice around 3. After driving for up to 20 minutes above 15 mph the wheels or wheel housings. (24 km/h), the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then 4. Using tire chains on the vehicle. remain on solid. 5. Using wheels/tires not equipped with TPMS sensors. 4.
STARTING AND OPERATING 533 Premium System – If Equipped TPMS Low Pressure Warnings The TPMS uses wireless technology with wheel rimmounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the Receiver Module. The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low.
534 STARTING AND OPERATING NOTE: The vehicle may need to be driven for up to 20 message will not be present, and a pressure value will be minutes above 15 mph (24 km/h) to receive this infor- displayed instead of dashes. A system fault can occur by any of the following scenarios: mation. 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the The “Tire Pressure Monitoring Telltale Light” will flash TPMS sensors.
STARTING AND OPERATING 535 message is then followed by a graphic display with 3. After driving the vehicle for up to 20 minutes above pressure values still shown. This indicates that the pres15 mph (24 km/h), the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and sure values are still being received from the TPM sensors then remain on solid. In addition, the EVIC will but they may not be in the correct vehicle position.
536 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the “Tire Pressure Monitoring Telltale Light” will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low pressure warning limit in any of the four active road tires.
STARTING AND OPERATING 537 high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such 3.6L Engine as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline This engine is designed to meet all emis- before considering service for the vehicle.
538 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
STARTING AND OPERATING 539 E-85 Usage In Non-Flex Fuel Vehicles • change the engine oil and oil filter Non-FFV vehicles are compatible with gasoline contain- • disconnect and reconnect the battery to reset the ing 10% ethanol (E10). Gasoline with higher ethanol engine controller memory content may void the New Vehicle Limited Warranty. More extensive repairs will be required for prolonged If a Non-FFV vehicle is inadvertently fueled with E-85 exposure to E-85 fuel.
540 STARTING AND OPERATING therefore, you should ask your gasoline retailer whether Fuel System Cautions the gasoline contains MMT. MMT is prohibited in Federal and California reformulated gasoline. CAUTION! Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost.
STARTING AND OPERATING 541 CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.
542 STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL — IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel vehicles only.
STARTING AND OPERATING 543 Ethanol Fuel (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! E-85 Badge Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
544 STARTING AND OPERATING Fuel Requirements NOTE: If your vehicle is E-85 compatible, it will operate on • Use seasonally adjusted E-85 fuel (ASTM D5798). With unleaded gasoline with an octane rating of 87, or E-85 non-seasonally adjusted E-85 fuel, you may experience fuel, or any mixture of these two fuels.
STARTING AND OPERATING 545 Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils. These special requirements are included in MOPAR® engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer only recommends engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
546 STARTING AND OPERATING Replacement Parts ADDING FUEL Many components in your Flexible Fuel Vehicle (FFV) are Fuel Filler Cap (Gas Cap) designed to be compatible with ethanol. Always be sure The gas cap is located behind the fuel filler door on the that your vehicle is serviced with correct ethanol comleft side of the vehicle. If the gas cap is lost or damaged, patible parts. be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING 547 NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
548 STARTING AND OPERATING • Tighten the fuel filler cap until you hear a “clicking” properly tightened. Refer to “Onboard Diagnostic Syssound. This is an indication that the fuel filler cap is tem” in “Maintaining Your Vehicle” for further information. properly tightened. • If the gas cap is not tightened properly, the MIL may If the problem continues, the message will appear the come on. Be sure the gas cap is tightened every time next time the vehicle is started.
STARTING AND OPERATING 549 The label contains the following information: Gross Axle Weight Rating (GAWR) • Name of manufacturer The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
550 STARTING AND OPERATING Rim Size Overloading This is the rim size that is appropriate for the tire size The load carrying components (axle, springs, tires, listed. wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the Inflation Pressure front and rear GAWR. This is the cold tire inflation pressure for your vehicle for The best way to figure out the total weight of your all loading conditions up to full GAWR.
STARTING AND OPERATING 551 Loading TRAILER TOWING To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you have exceeded either GAWR, but the total load is within the specified GVWR, you must redistribute the weight.
552 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle rear GAWR. Refer to “Vehicle Loading/Vehicle CertificaCertification Label” in “Starting and Operating” for tion Label” in “Starting and Operating” for further information. further information.
STARTING AND OPERATING 553 Trailer Sway Control Weight-Distributing Hitch The trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. A weight-distributing system works by applying leverage through spring (load) bars.
554 STARTING AND OPERATING WARNING! • An improperly adjusted weight-distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • Weight-distributing hitch systems may not be compatible with surge brake couplers. Consult with an authorized hitch and trailer manufacturer or a reputable authorized Recreational Vehicle dealer for additional information.
STARTING AND OPERATING 555 5 With Weight-Distributing Hitch (Correct) Improper Adjustment Of Weight-Distributing Hitch (Incorrect)
556 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING 557 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Transmission GCWR (Gross Combined Weight Rating) 8,750 lbs (3 969 kg) Frontal Area Up to 2 persons & Luggage 3,600 lbs (1 633 kg)* 8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) 3 to 5 persons & Luggage 3,350 lbs (1 519 kg)* 8,750 lbs (3 969 kg) 40 sq ft (3.
558 STARTING AND OPERATING NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tire Safety Information” in “Starting and Operating” for further information. Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING 559 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle. Towing Requirements CAUTION! • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven.
560 STARTING AND OPERATING WARNING! WARNING! (Continued) Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision.
STARTING AND OPERATING 561 WARNING! (Continued) • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized. Towing Requirements – Tires • Check the trailer tires for proper tire inflation pressures before trailer usage. • Check for signs of tire wear or visible tire damage before towing a trailer.
562 STARTING AND OPERATING • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
STARTING AND OPERATING 563 Towing Requirements – Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four- and sevenpin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
564 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, use the Electronic Range Select (ERS) shift control to select a lower gear range.
STARTING AND OPERATING 565 or frequent trailer towing.” Refer to the “Maintenance Cooling System Schedule” for the proper maintenance intervals. To reduce potential for engine and transmission overheating, take the following actions: Electronic Speed Control – If Equipped • Do not use in hilly terrain or with heavy loads.
566 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 567 Recreational Towing – All Models Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer’s instructions. 2. Drive the front wheels onto the tow dolly. 3. Firmly apply the parking brake. Place the transmission in PARK. 4.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .570 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . .580 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .570 ▫ Securing The Spare Tire . . . . . . . . . . . . . . . . .587 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .571 ▫ Road Tire Installation . . . . . . . . . . . . . . . . . . .589 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .572 䡵 JUMP-STARTING . . . . . . . . . . . . . . . . . . . .
570 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the lower center area of the instrument panel. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all direc- • On the highways — slow down.
WHAT TO DO IN EMERGENCIES 571 CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
572 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover.
WHAT TO DO IN EMERGENCIES 573 Spare Tire Removal The spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console or under front super console forward bin liner.
574 WHAT TO DO IN EMERGENCIES To Access Spare Tire Winch Drive Nut To access the spare tire winch drive nut and lower the spare tire, you will need to refer to one of the following center console configurations. Super Console For vehicles equipped with the Super Console, the spare tire winch assembly drive nut is located beneath the console. Super Console 1 — Lower Drawer 2 — Front Drawer 3 — Front Drawer Liner 1.
WHAT TO DO IN EMERGENCIES 575 2. Open the front drawer to expose the storage compart- Premium/Base/Cargo Center Console ment. Pull the Winch Cover assembly plug (if equipped) to 3. Remove the liner from the console’s storage compart- access the winch drive nut. ment to access the spare tire winch drive nut.
576 WHAT TO DO IN EMERGENCIES Spare Tire Tools The tool pouch contains three pieces and can be assembled into a spare tire hook; to remove the compact spare tire/cover assembly from under the vehicle, or a Winch T-handle; to raise/lower the compact spare tire/ cover assembly.
WHAT TO DO IN EMERGENCIES 577 Spare Tire Removal Instructions The spare tire is located under the vehicle beneath the center console area. 6 Assembling The Spare Tire Hook A — Spare Tire Hook/T-handle B — Extension 1 C — Extension 2 Spare Tire And Cover 1. Assemble the spare tire tools into a T-handle and place the square end over the spare tire winch drive nut.
578 WHAT TO DO IN EMERGENCIES 2. Rotate the nut to the left until the winch mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the spare tire out from underneath the vehicle. CAUTION! The winch mechanism is designed for use with the winch T-handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3.
WHAT TO DO IN EMERGENCIES 579 4. Stand the tire/cover assembly upright and remove the Preparations For Jacking wheel spacer by squeezing the winch retaining tabs 1. Park the vehicle on a firm, level surface. Avoid ice or together. Push the retainer through the spare tire to slippery areas. release it from the wheel. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2.
580 WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the wheel diagonally Jacking Instructions opposite the jacking position. For example, if changing the right front WARNING! tire, block the left rear wheel. Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the NOTE: Passengers should not remain in the vehicle vehicle.
WHAT TO DO IN EMERGENCIES 581 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
582 WHAT TO DO IN EMERGENCIES 2. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body.
WHAT TO DO IN EMERGENCIES 583 Front jack location is on the sill flange of the vehicle body NOTE: In some situations the jack may need to be and is located 6 in (150 mm) from door edge. placed on its side in order to be pushed under the vehicle. Return the jack to its correct orientation once it is under the vehicle. WARNING! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
584 WHAT TO DO IN EMERGENCIES 4. Raise the vehicle by turning the jack screw to the right, 5. Remove the wheel lug nuts, for vehicles with wheel using the swivel wrench. Raise the vehicle only until covers, remove the cover from the wheel by hand. Do the tire just clears the surface and enough clearance is not pry the wheel cover off. Then pull the wheel off the obtained to install the spare tire. Minimum tire lift hub. provides maximum stability. 6. Install the compact spare tire.
WHAT TO DO IN EMERGENCIES 585 NOTE: Do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct wheel nut tightness is 100 ft lbs (135 N·m).
586 WHAT TO DO IN EMERGENCIES 9. Lower the jack to its fully-closed position. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 11. Stow the cable and wheel spacer before driving the vehicle. Reassemble the winch handle extensions to form a “T” and fit the winch T-handle over the drive nut.
WHAT TO DO IN EMERGENCIES 587 Securing The Spare Tire CAUTION! 1. Assemble the winch handle extensions to form a T-handle and fit the winch T-handle over the drive The winch mechanism is designed for use with the nut. Rotate the nut to the left until the winch mecha- winch T-handle only. Use of an air wrench or other nism stops turning freely. This will allow enough slack power tools is not recommended and can damage the in the cable to allow you to pull the wheel spacer out winch.
588 WHAT TO DO IN EMERGENCIES CAUTION! The compact spare tire/cover assembly must be used when the compact spare tire is stored. Failure to use this cover could drastically reduce the life of the compact spare tire. WARNING! Verify that both retainer tabs of the wheel spacer have been properly extended through the center of the wheel and spare tire/cover assembly.
WHAT TO DO IN EMERGENCIES 589 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
590 WHAT TO DO IN EMERGENCIES 3. Align the valve notch in the wheel cover with the 5. Lower the vehicle to the ground by turning the jack valve stem on the wheel. Install the cover by hand, handle counterclockwise. snapping the cover over the two lug nuts. Do not use 6. Finish tightening the lug nuts. Push down on the a hammer or excessive force to install the cover. wrench while at the end of the handle for increased 4. Install the remaining lug nuts with the cone shaped leverage.
WHAT TO DO IN EMERGENCIES 591 Vehicles Without Wheel Covers 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4.
592 WHAT TO DO IN EMERGENCIES JUMP-STARTING If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.
WHAT TO DO IN EMERGENCIES 593 Preparations For Jump-Start The battery in your vehicle is located on the left side of the engine compartment. Positive Battery Post WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured.
594 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 595 WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle.
596 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between DRIVE and REVERSE while gently pressing the accelerator. Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.
WHAT TO DO IN EMERGENCIES 597 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed.
598 WHAT TO DO IN EMERGENCIES 4. Press and maintain firm pressure on the brake pedal. 5. Insert the screwdriver or similar tool into the access hole, and push and hold the override release lever forward. 6. Move the shift lever to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8. Reinstall the shift lever override access cover.
WHAT TO DO IN EMERGENCIES 599 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service.
600 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES 601 The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed. If flatbed equipment is not available, and the transmission is operable, the vehicle may be flat towed (with all four wheels on the ground) under the following conditions: • The transmission must be in NEUTRAL. • The towing distance must not exceed 15 miles (24 km). • The towing speed must not exceed 25 mph (40 km/h).
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .605 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .614 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . . .606 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . .614 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .607 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .616 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . .607 ▫ Air Conditioner Maintenance . . . . . . . . . . .
604 MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .633 ▫ Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . .652 ▫ Cleaning The Instrument Panel Cupholders . . .640 ▫ Rear Tail, Stop, Turn Signal, Side Marker And Backup Lamps . . . . . . . . . . . . . . . . . . . . . . .653 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .640 ▫ Center High-Mounted Stop Lamp (CHMSL) . . .
MAINTAINING YOUR VEHICLE 605 ENGINE COMPARTMENT — 3.
606 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 607 Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE If the vehicle diagnostic system determines that the fuel PROGRAMS filler cap is loose, improperly installed, or damaged, a In some localities, it may be a legal requirement to pass “gASCAP” message will display in the odometer or a an inspection of your vehicle’s emissions control system. “CHECK GASCAP” message will be displayed in the Failure to pass could prevent vehicle registration.
608 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, 4. Approximately 15 seconds later, one of two things will which you can use prior to going to the test station. To happen: check if your vehicle’s OBD II system is ready, you must • The MIL will flash for about 10 seconds and then do the following: return to being fully illuminated until you turn OFF 1. Cycle the ignition switch to the ON position, but do the ignition or start the engine.
MAINTAINING YOUR VEHICLE 609 Regardless of whether your vehicle’s OBD II system is ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. REPLACEMENT PARTS Use of genuine MOPAR® parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
610 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future.
MAINTAINING YOUR VEHICLE 611 check the engine oil level is about five minutes after a Change Engine Oil fully warmed engine is shut OFF or before starting the The oil change indicator system will remind you that it is engine after it has sat overnight. time to take your vehicle in for scheduled maintenance. Checking the oil while the vehicle is on level ground will Refer to the “Maintenance Schedule” for further informaimprove the accuracy of the oil level readings. Maintain tion.
612 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol Engine Oil Viscosity – 3.6L Engine SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature This symbol means that the oil has starting and vehicle fuel economy. been certified by the American The engine oil filler cap also shows the recommended Petroleum Institute (API). The engine oil viscosity for your engine.
MAINTAINING YOUR VEHICLE 613 Materials Added To Engine Oil Engine Oil Filter The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter.
614 MAINTAINING YOUR VEHICLE used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recomRefer to the “Maintenance Schedule” for the proper mended. maintenance intervals. Exhaust System Engine Air Cleaner Filter WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE 615 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
616 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE 617 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. • Battery gas is flammable and explosive.
618 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
MAINTAINING YOUR VEHICLE 619 Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. The A/C air filter is located in the fresh air inlet behind the glove box.
620 MAINTAINING YOUR VEHICLE 6. Install the A/C air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. A/C Air Filter Replacement 5. Remove the A/C air filter by pulling it straight out of the housing. 7.
MAINTAINING YOUR VEHICLE 621 Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR® Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
622 MAINTAINING YOUR VEHICLE Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out any residual water. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you.
MAINTAINING YOUR VEHICLE 623 Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
624 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, And Refill If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (antifreeze) (conforming to MS12106). Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 625 CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
626 MAINTAINING YOUR VEHICLE • Mix a minimum solution of 50% OAT engine coolant that meets the requirements of Chrysler Material Standard MS-12106 and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below −34° F (−37° C) are anticipated. NOTE: Mixing engine coolant (antifreeze) types is not recommended and can result in cooling system damage.
MAINTAINING YOUR VEHICLE 627 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
628 MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month.
MAINTAINING YOUR VEHICLE 629 • If frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • Maintain engine coolant (antifreeze) concentration at a minimum of 50% OAT coolant (conforming to MS12106) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean.
630 MAINTAINING YOUR VEHICLE Master Cylinder – Brake Fluid Level Check The fluid level in the master cylinder should be checked when performing underhood services, or immediately if the “Brake System Warning Light” indicates system failure. Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system.
MAINTAINING YOUR VEHICLE 631 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
632 MAINTAINING YOUR VEHICLE important to maintain the transmission fluid at the Special Additives correct level using the recommended fluid. No chemical The manufacturer strongly recommends against using flushes should be used in any transmission; only the any special additives in the transmission. approved lubricant should be used. Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by suppleCAUTION! mental additives.
MAINTAINING YOUR VEHICLE 633 Fluid Level Check Fluid And Filter Changes The fluid level is preset at the factory and does not require adjustment under normal operating conditions. Routine fluid level checks are not required, therefore the transmission filler tube is capped and no dipstick is provided. Your authorized dealer can check your transmission fluid level using a special service dipstick.
634 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your vebody protection. hicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with The following maintenance recommendations will enable clear water. you to obtain maximum benefit from the corrosion resistance built into your vehicle.
MAINTAINING YOUR VEHICLE 635 CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
636 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. • For chrome wheels, use MOPAR® Chrome Cleaner (Part#04318013) or equivalent. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes.
MAINTAINING YOUR VEHICLE 637 • For tough stains, apply MOPAR® Total Clean, or a Cleaning Interior Trim mild soap solution to a clean, damp cloth and remove Interior trim should be cleaned starting with a damp stain. Use a fresh, damp towel to remove soap residue. cloth, a damp cloth with MOPAR® Total Clean or equiva• For grease stains, apply MOPAR® Multi-Purpose lent, then MOPAR® Spot & Stain Remover or equivalent Cleaner to a clean, damp cloth and remove stain. Use if absolutely necessary.
638 MAINTAINING YOUR VEHICLE liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
MAINTAINING YOUR VEHICLE 639 When cleaning the rear view mirror, spray cleaner on the Seat Belt Maintenance towel or rag that you are using. Do not spray cleaner Do not bleach, dye, or clean the belts with chemical directly on the mirror. solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric.
640 MAINTAINING YOUR VEHICLE Cleaning The Instrument Panel Cupholders Installation Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the Pull the flexible liner from the cupholder drawer starting corresponding openings in the drawer. at one edge to ease removal. FUSES Cleaning Removal The liner is top shelf dishwasher safe, or you may follow the cleaning procedure below.
MAINTAINING YOUR VEHICLE 641 CAUTION! Totally Integrated Power Module • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
642 MAINTAINING YOUR VEHICLE Cavity J1 J2 J3 J4 J5 J6 Cartridge Fuse 40 Amp Green 30 Amp Pink 30 Amp Pink 25 Amp Natural 25 Amp Natural 40 Amp Green MiniFuse Description Cavity — Power Folding Seat J7 — Power Liftgate Module Rear Door Module J8 — J9 — Driver Door Node — Passenger Door Node Antilock Brakes Pump/Stability Control System — J10 Cartridge Fuse 30 Amp Pink MiniFuse — 40 Amp Green 40 Amp Green — 30 Amp Pink — — Description Antilock Brakes Valve/Stability Control System Po
MAINTAINING YOUR VEHICLE 643 Cavity J11 J12 J13 J14 J15 J17 Cartridge Fuse 30 Amp Pink 30 Amp Pink 60 Amp Yellow 40 Amp Green 40 Amp Green 40 Amp Green MiniFuse Description Cavity J18 — Power Sliding Door Module/Anti–Theft Module – If Equipped HVAC Rear Blower, Radiator Fan Motor Ignition Off Draw (IOD) – Main Rear Window Defogger Front Blower — Starter Solenoid — — — J19 J20 J21 J22 M1 Cartridge Fuse 20 Amp Blue 60 Amp Yellow 30 Amp Pink 20 Amp Blue 25 Amp Natural — MiniFuse — Description
644 MAINTAINING YOUR VEHICLE M2 Cartridge Fuse — M3 — M4 — M5 — M6 — Cavity MiniFuse 20 Amp Yellow 20 Amp Yellow 10 Amp Red 25 Amp Natural 20 Amp Yellow Description Cavity Front Fog Lamps M7 Cartridge Fuse — Front/Rear Axle Locker, Vacuum Pump Motor Trailer Tow M8 — Inverter M9 — Power Outlet #1 (ACC), Rain Sensor, Cigar Lighter (Instrument Panel or with Console Rear) MiniFuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Power Outlet #2 (BATT/ACC SELECT) – Center Seat or
MAINTAINING YOUR VEHICLE 645 Cavity M10 Cartridge Fuse — M11 — M12 — MiniFuse 15 Amp Blue 10 Amp Red 30 Amp Green Description Cavity Ignition Off Draw — Video System, Satellite Radio, DVD, Hands-Free Module, Universal Garage Door Opener, Vanity Lamp, Streaming Video Module – If Equipped Climate Control System Amplifier/Radio M13 Cartridge Fuse — M14 — M15 — MiniFuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Instrument Cluster, SIREN, Clock Module, Multi-Function Control Switc
646 MAINTAINING YOUR VEHICLE M16 Cartridge Fuse — M17 — 15 Amp Blue M18 — M19 — 15 Amp Blue 25 Amp Natural Cavity MiniFuse 10 Amp Red Description Cavity Airbag Module/ Occupant Classification Module Left Tail/License/ Park Lamp, Running Lamps Right Tail/Park/ Run Lamp Powertrain M20 Cartridge Fuse — M21 — M22 — M23 — MiniFuse 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red Description Instrument Cluster Interior Light, Switch Bank, Steering Column Module, Switch Steering Wheel Powe
MAINTAINING YOUR VEHICLE 647 M24 Cartridge Fuse — M25 — M26 — 10 Amp Red M27 — 10 Amp Red M28 — 10 Amp Red Cavity MiniFuse 25 Amp Natural 20 Amp Yellow Description Cavity Rear Wiper M29 Cartridge Fuse — Fuel Pump, Diesel Lift Pump – If Equipped Power Mirror Switch, Driver Window Switch Wireless Control Module, Keyless Entry Module Powertrain, Transmission Control Module M30 — M31 — M32 — M33 — MiniFuse 10 Amp Red 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red Description Occu
648 MAINTAINING YOUR VEHICLE Cavity M34 M35 Cartridge Fuse — — MiniFuse 10 Amp Red 10 Amp Red Description Cavity Park Assist, Heater Climate Control Module, Headlamp Wash, Compass, Rear Camera, Door Lamps, Flashlight, Relay Diesel Cabin Heater, Rad Fan Diesel – If Equipped Heated Mirrors M36 Cartridge Fuse — M37 — 10 Amp Red M38 — 25 Amp Natural MiniFuse 20 Amp Yellow Description Power Outlet #3 (Instrument Panel or with Console Center) Antilock Brakes, Stability Control, Stop Lamp, Fuel
MAINTAINING YOUR VEHICLE 649 VEHICLE STORAGE REPLACEMENT BULBS If you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. Interior Bulbs You may do the following: • Remove the 60 Amp cartridge in the Totally Integrated Center & Rear Dome Power Module (TIPM) labeled Ignition-Off Draw Lamp (IOD). Center & Rear Reading Lamps • Or, disconnect the negative cable from the battery.
650 MAINTAINING YOUR VEHICLE Instrument Cluster Lamps Liftgate Lamp(s) Overhead Console Reading Lamps Removable Console Lamp – If Equipped Visor Vanity Lamps Bulb Number PC74 578 PC579 194 6501966 NOTE: For lighted switches, see your authorized dealer for replacement instructions.
MAINTAINING YOUR VEHICLE 651 BULB REPLACEMENT Headlamps 1. Raise the hood to access the rear of the headlamp housing. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 2. Slide the red lock tab rearward on the connector, then depress the tab and remove the connector from the 5. Connect the wiring connector to bulb and slide red bulb. lock tab forward. 3.
652 MAINTAINING YOUR VEHICLE Fog Lamps NOTE: Access to the fog lamp bulb is from the rear of the fascia. On the left rear side of the fascia, remove the push pin and lower the hinged access door on the air dam. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 1.
MAINTAINING YOUR VEHICLE 653 Rear Tail, Stop, Turn Signal, Side Marker And Backup Lamps 1. Raise the liftgate. 2. Remove the tail lamp assembly by removing the two screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs. NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint.
654 MAINTAINING YOUR VEHICLE 3. Twist the socket and remove from the lamp assembly. License Lamp 4. Pull the bulb to remove it from the socket. The license plate lamp is located under the tailgate light bar and above the license plate. 5. Replace the bulb, reinstall the socket, and reattach the 1. Using a small screwdriver, press inward the locking lamp assembly. tab on the outboard side of the lamp assembly and Center High-Mounted Stop Lamp (CHMSL) pull down on the lamp assembly for removal.
MAINTAINING YOUR VEHICLE 655 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 20 Gallons 76 Liters Engine Oil with Filter 3.6L Engine (SAE 5W-20, API Certi6 Quarts 5.6 Liters fied) Cooling System * 3.6L Engine (MOPAR® Antifreeze/ 13.4 Quarts 12.6 Liters Engine Coolant 10 Year/150,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a rear heater.
656 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-12106. We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 657 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part We recommend you ONLY use MOPAR® ATF+4® Automatic Transmission Fluid. Failure to use ATF+4® fluid may affect the function or performance of your transmission. We recommend you use MOPAR® DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .660 ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 660 MAINTENANCE SCHEDULES than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)/Oil Change Required” in indicator system. The oil change indicator system will “Understanding Your Instrument Panel” for further inremind you that it is time to take your vehicle in for formation. scheduled maintenance.
MAINTENANCE SCHEDULES 661 M Required Maintenance Intervals. Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • Inspect battery and clean and tighten terminals as required. • Inspect automatic transmission fluid if equipped with dipstick.
S C H E D U L E S 8 Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the brake linings, replace as necessary. Adjust parking brake on vehicles equipped with four wheel disc brakes.
Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace spark plugs (3.6L engine). ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
S C H E D U L E S 8 Change automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Change automatic transmission fluid and filter. Inspect and replace PCV valve if necessary.
MAINTENANCE SCHEDULES 665 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . .669 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .671 ▫ Prepare For The Appointment. . . . . . . . . . . . .669 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .671 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .669 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .672 ▫ Be Reasonable With Requests . .
668 IF YOU NEED CONSUMER ASSISTANCE 䡵 PUBLICATION ORDER FORMS . . . . . . . . . . . .674 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .675 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .675 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .676 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 669 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
670 IF YOU NEED CONSUMER ASSISTANCE Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE 671 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1 800 855-0511 to connect with a Bell Relay Service operator.
672 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 673 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– operating at its best. 9153), or go to http://www.safercar.
674 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 675 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
676 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
678 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .625 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .546 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .622 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .540 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .234 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 679 Automatic Transmission . . . . . . . . . . . . . . . . . . . .468 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .633 Fluid and Filter Changes . . . . . . . . . . . . . . . . . .633 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . .633 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .633 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .631 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .473 Special Additives . . . . . .
680 INDEX Carbon Monoxide Warning . . . . . . . . . . . . . . . . . .118 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . .294 Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . .294 Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . .298 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . .285 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .634 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 681 Dealer Service. . . . . . . . . . . . . . . . . . . . . . . . . . . .609 Defroster, Windshield . . . . . . . . . . . . . . . . . . . . . .120 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . .229 Diagnostic System, Onboard . . . . . . . . . . . . . . . . .606 Dimmer Control . . . . . . . . . . . . . . . . . . . . . . . . . .224 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . . .633 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .610 Power Steering .
682 INDEX E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . Economy (Fuel) Mode . . . . . . . . . . . . . . . . . Electrical Power Outlets. . . . . . . . . . . . . . . . Electric Remote Mirrors . . . . . . . . . . . . . . . . Electronic Brake Control System . . . . . . . . . . Brake Assist System . . . . . . . . . . . . . . . . Electronic Speed Control (Cruise Control) . . . Electronic Stability Control (ESC) . . . . . . . . . Electronic Vehicle Information Center (EVIC) .
INDEX 683 Turn Signal . . . . . . . . . Enhanced Accident Response Feature . . . . . . . . . . . .86 Entry System, Illuminated . . . . . . . . . . . . . . . . . . . .20 Flash-To-Pass . . . . . . . . . . Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .538 Flexible Fuel Vehicles Cruising Range . . . . . . . Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . . .90 Engine Oil . . . . . . . . . . Exhaust Gas Caution. . . . . . . . . . . . . . . . . . . . . . . .
684 INDEX Power Steering . . . . . . . . . . . . . . Fluids, Lubricants and Genuine Parts Fog Lights . . . . . . . . . . . . . . . . . . . Fog Light Service . . . . . . . . . . . . . . Fold in Floor (Stow ⬘n Go) Seating . . Freeing A Stuck Vehicle . . . . . . . . . . Fuel . . . . . . . . . . . . . . . . . . . . . . . . Adding . . . . . . . . . . . . . . . . . . . Additives . . . . . . . . . . . . . . . . . . Clean Air . . . . . . . . . . . . . . . . . . Conserving . . . . . . . . . . . . . . . . .
INDEX 685 Hazard Warning Flasher . . . . . . . . . . . . . . . . . Headlights Bulb Replacement . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . Lights On Reminder . . . . . . . . . . . . . . . . . . Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . Washers . . . . . . . . . . . . . . . . . . . . . . . . . . .
686 INDEX Hook, Coat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . . .14 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . . .20 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . .
INDEX 687 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .523 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Light Bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . .
688 INDEX Security Alarm (Theft Alarm) . . . . . . . . . . . . . . .324 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .649 Service Engine Soon (Malfunction Indicator) . . . .321 Side Marker . . . . . . . . . . . . . . . . . . . . . . . . . . .653 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . .324 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . .319 Traction Control . . . . . . . . . . . . . . . . . . . . . . . .496 Turn Signal . . . . . . . . . . . . . . . . . . . . .
INDEX 689 Mode Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 Modifications/Alterations, Vehicle . . . . . . . . . . . . . . .8 Monitor, Tire Pressure System . . . . . . . . . . . . . . . .528 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .609 MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . .538 Multi-Function Control Lever . . . . . . . . . . . . . . . . .226 New Vehicle Break-In Period . . . . . . . . . . . . . . . . .117 Occupant Restraints .
690 INDEX Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .633 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Parking Brake. . . . . . . . . . . . . . . . . . . . . . . . . . . .487 Park Sense System, Rear . . . . . . . . . . . . . . . . . . . .239 Pedals, Adjustable. . . . . . . . . . . . . . . . . . . . . . . . .234 Personal Settings. . . . . . . . . . . . . . . . . . . . . . . . . .346 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 691 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . . .191 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . .90 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . .566 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . .538 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .619 Reminder, Seat Belt. . . . . . . . . . . . . . . . . . . . . . . . .73 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . .
692 INDEX Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .182 Fold in Floor (Stow ⬘n Go) . . . . . . . . . . . . . . . . .196 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 Power . .
INDEX 693 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .485 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . .232 Wheel, Heated . . . . . . . . . . . . . . . . . . . . . . . . .233 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .232 Steering Wheel Audio Controls . . . . . . . . . . . . . . .435 Steering Wheel Mounted Sound System Controls . . .435 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .649 Storage Bin. . . . . .
694 INDEX Life of Tires . . . . . . . . . . . . . . . Load Capacity . . . . . . . . . . . . . Pressure Monitor System (TPMS) Pressure Warning Light . . . . . . . Quality Grading . . . . . . . . . . . . Radial . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . . Rotation . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . Sizes . . . . . . . . . . . . . . . . . . . . Snow Tires . . . . . . . . . . . . . . . . Spare Tire . . . . . . . . . . . . . . . .
INDEX 695 Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . . .637 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .557 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .631 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .468 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .631 Transmitter Battery Service (Remote Keyless Entry) . . .28 Transmitter, Garage Door Opener (HomeLink®). . . .
696 INDEX Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .483 Wind Buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . .459 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Windshield Defroster. . . . Windshield Washers . . . .
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
Chrysler Group LLC 13MZZ-126-AE 300 5th Edition Printed in U.S.A.
