2014 C h a s s i s C a b 2014 OWNER’S MANUAL Chrysler Group LLC 14DD43-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VAN CONVERSIONS/CAMPERS . . . . . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .6 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .
4 INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained techniLLC vehicle. Be assured that it represents precision cians and genuine parts, and cares about your satisfaction. workmanship, distinctive styling, and high quality - all HOW TO USE THIS MANUAL essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury.
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER 1 The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle frame and underbody as well as the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM . . . . . . . . . . . . . .21 ▫ Ignition Node Module (IGNM) — If Equipped. .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .21 ▫ Keyless Ignition Node (KIN) — If Equipped . . .13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .21 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ To Disarm The System . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .28 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .48 ▫ Programming Additional Transmitters. . . . . . . .29 䡵 OCCUPANT RESTRAINTS . . . . . . . . . . . . . . . .48 ▫ Transmitter Battery Replacement . . . . . . . . . . .29 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . .51 ▫ General Information . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver and Right Front Passenger Supplemental 䡵 DIESEL ENGINE BREAK-IN Restraint System (SRS) — Air Bags . . . . . . . . .64 RECOMMENDATIONS . . . . . . . . . . . . . . . . . .108 ▫ Air Bag System Components . . . . . . . . . . . . . .66 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .109 ▫ Advanced Front Air Bag Features . . . . . . . . . . .66 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Node Module (IGNM) — If Equipped Your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a Key Fob with Remote Keyless Entry (RKE) transmitter and an Ignition Node Module (IGNM).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Keyless Ignition Node (KIN) — If Equipped This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START; during start RUN will illuminate.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 2 Emergency Key Removal (IGNM) Emergency Key Removal Keyless Enter-N-Go™ Fob (KIN) NOTE: You can insert the double-sided emergency key into the lock cylinder with either side up.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition Place the shift lever in PARK (if equipped with an automatic transmission). Turn the Key Fob to the OFF position and then remove the Key Fob. NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! WARNING! (Continued) • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and push ignition button to place ignition in OFF position. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder SENTRY KEY® Opening the driver’s door when the Key Fob is in the The Sentry Key® Immobilizer System prevents unauthorignition and the ignition switch position is OFF or ACC, ized vehicle operation by disabling the engine. The system a chime will sound to remind you to remove the Key Fob. does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or NOTE: unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 During normal operation, after turning on the ignition CAUTION! switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the The Sentry Key® Immobilizer system is not compatbulb check, it indicates that there is a problem with the ible with some aftermarket remote starting systems. electronics.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended. • For vehicles equipped with Keyless Enter-N-Go™, always remember to place the ignition in the OFF position. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: Changes or modifications not expressly approved Rearming Of The System by the party responsible for compliance could void the The Vehicle Security Alarm will rearm itself after the 15 user’s authority to operate the equipment. additional minutes of headlights and Vehicle Security Light flashing, if the system has not been disabled.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, Use the RKE transmitter to unlock the door. If something disarm the Vehicle Security Alarm. has triggered the Vehicle Security Alarm in your absence, the horn will sound three times when you unlock the Security System Manual Override doors and the exterior lights will blink three times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 The lights will fade to off after approximately 30 seconds, REMOTE KEYLESS ENTRY (RKE) — or they will immediately fade to off once the ignition IF EQUIPPED switch is turned to ON/RUN from the OFF position.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob With Remote Keyless Entry (RKE) Transmitter Key Fob With Keyless Enter-N-Go™ Fob (KIN)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the following procedure: Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door (If EVIC is 1. Press and hold the LOCK button on a programmed setup for driver door first, otherwise this will unlock all RKE transmitter for at least four seconds, but no doors), or press the unlock button twice within five longer than ten seconds.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmit- • For vehicles not equipped with the EVIC, perform the ter while you are inside the vehicle will activate the following procedure: Vehicle Security Alarm System. Opening a door with the 1. Press and hold the UNLOCK button on a programmed Vehicle Security Alarm System activated will cause the RKE transmitter for at least four seconds, but no alarm to sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: Pressing the LOCK button on the RKE transmitter while you are in the vehicle will activate the Vehicle Security Alarm System. Opening a door with the Vehicle Security Alarm System activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm System. Sound Horn With Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the headlights will turn on, the park lights will flash, the horn will pulse on and off, and the interior lights will 3. Test the feature while outside of the vehicle by pressturn on. ing the LOCK button on the RKE transmitter with the ignition switch in the OFF position and the key The Panic Alarm will stay on for three minutes unless you turn it off by either pressing the PANIC button a removed. second time or drive the vehicle at a speed of 5 mph 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Programming Additional Transmitters If you do not have a programmed RKE transmitter, contact your authorized dealer for details. 2 Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate • Do not touch the battery terminals that are on the back housing or the printed circuit board. 1.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keyless Ignition Node (KIN) Emergency Key Removal 2. Separating RKE halves requires screw removal and gently prying the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 2 Separating Ignition Node Module (IGNM) Transmitter Case Separating Keyless Ignition Node (KIN) Transmitter Case 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: • Battery at an acceptable charge level • The vehicle must be equipped with an automatic • transmission to be equipped with Remote Start. • • Obstructions between the vehicle and the RKE trans• mitter may reduce this range.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped To Enter Remote Start Mode The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prematurely: • Remote Start Aborted — Hood Ajar Press and release the REMOTE START button on the RKE transmitter twice within five seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of the 15-minute cycle, press and release in the Remote Start mode. the UNLOCK button on the RKE transmitter to unlock • The engine can be started two consecutive times (two the doors and disarm the Vehicle Security Alarm System 15-minute cycles) with the RKE transmitter.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Comfort Systems — If Equipped DOOR LOCKS When remote start is activated, the heated steering wheel Manual Door Locks and driver heated seat features will automatically turn on Front and rear doors may be locked by moving the lock in cold weather. In warm weather, the driver vented seat knob down or unlocked by moving the lock knob up. feature will automatically turn on when the remote start is activated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accidentally locking your Key Fob in the vehicle. Removing the Key Fob or closing the door will allow the locks to A power door LOCK switch is on each front door trim operate. A chime will sound if the Key Fob is in the panel. Use this switch to lock or unlock the doors. ignition switch and a door is open, as a reminder to remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Automatic Doors Unlock Programming — If Equipped The Automatic Doors Unlock feature can be enabled or disabled as follows: 2 For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (System Setup)” in “Understanding Your Instrument Panel” for further information. NOTE: Use the Auto Unlock Doors feature in accordance with local laws.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • After setting the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle. KEYLESS ENTER-N-GO™ Child Lock Control WARNING! Avoid trapping anyone in a vehicle in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: To Unlock From The Driver’s Side: • Passive Entry may be programmed ON/OFF; refer to With a valid Passive Entry RKE transmitter within 5 ft “Uconnect® Settings” in “Understanding Your Instru- (1.5 m) of the driver door handle, grab the front driver door handle to unlock the driver’s door automatically. ment Panel” for further information.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If “Unlock All Doors 1st Press” is programmed, all doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press”, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 To Lock The Vehicle’s Doors With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, press the door handle LOCK button to lock all doors. Do NOT grab the door handle when pressing the door handle lock button. This could unlock the door(s).
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WINDOWS • After pressing the door handle LOCK button, you Power Windows — If Equipped must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • The Passive Entry system will not operate if the RKE transmitter battery is dead.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 and on the rear doors of the Quad Cab and Crew Cab models. The windows will operate when the ignition switch is turned to the ON/RUN or ACC position, and for up to 10 minutes after the ignition is turned OFF or until a front door is opened. WARNING! (Continued) particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Up Feature With Anti-Pinch Protection (4-Door Models Driver And Front Passenger Door Only) — If Equipped Lift the window switch fully upward to the second detent, release, and the window will go up automatically. WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Window LOCKOUT Switch (4–Door Models Only) The window LOCKOUT switch on the driver’s door allows you to disable the window control on the rear passenger doors. To disable the window controls on the rear passenger doors, press the window LOCK button into the latched or down position. To enable the window controls, press the window LOCK button again and return the switch to the released or up position.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • An energy-absorbing steering column and steering wheel Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the • Knee bolsters/blockers for front seat occupants ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain • All seat belt systems (except driver’s regular/Crew Cab®, first and second row center position for Crew open or partially open positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. Children that are not big enough to wear the vehicle seat belt properly (refer to “Child Restraints”) should be secured in the rear seat in child restraints or beltpositioning booster seats.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front Air Bags room to inflate. WARNING! (Continued) bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. 4. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Lap/Shoulder Belts All seating positions except the Crew Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in an collision the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! Latch Plate To Buckle • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Regular Cab Front Center Three Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the seat belt tongue into the center red slot on the black buckle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 2 Inserting Latch Plate In Use Position
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Adjustable Upper Shoulder Belt Anchorage As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 If the passenger seating position is equipped with an Automatic Locking Retractor Mode (ALR) — ALR and is being used for normal usage: If Equipped Only pull the belt webbing out far enough to comfortably wrap around the occupants mid-section so as to not activate the ALR. If the ALR is activated you will hear a ratcheting sound as the belt retracts.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode Center Lap Belts — Crew Cab® Only The front center seating position has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle 2. Grasp the shoulder portion and pull downward until until you hear a “click.” To lengthen the lap belt, tilt the the entire belt is extracted. latch plate and pull. To remove slack, pull the loose end 3. Allow the belt to retract.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The BeltAlert® warning sequence begins after the vehicle speed is over 5 mph (8 km/h), by blinking the Seat Belt Reminder Light and sounding an intermittent chime. Once the sequence starts, it will continue for the entire duration or until the respective seatbelts are fastened. After the sequence completes, the Seat Belt Reminder Light remains illuminated until the respective seat belts are fastened.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender Driver and Right Front Passenger Supplemental If a seat belt is too short even when fully extended and Restraint System (SRS) — Air Bags when the adjustable upper shoulder belt anchorage (if This vehicle has Advanced Front Air Bags for both the equipped) is in its lowest position, your authorized driver and front passenger as a supplement to the seat dealer can provide you with a seat belt extender. This belt restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Air Bags based upon seat position.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag System Components Advanced Front Air Bag Features Your vehicle may be equipped with the following air bag The Advanced Front Air Bag system has multistage system components: driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as • Occupant Restraint Controller (ORC) determined by the Occupant Restraint Controller (ORC).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE including the severity and type of collision. Advanced The ORC monitors the readiness of the electronic parts of Front Air Bags are not expected to reduce the risk of the air bag system whenever the ignition switch is in the START or ON/RUN position. If the key is in the LOCK injury in rear, side or rollover collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 It also includes diagnostics that will illuminate the instrument cluster Air Bag Warning Light if a malfunction is noted that could affect the air bag system. The diagnostics also record the nature of the malfunction. WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If A Deployment Occurs In the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: The Advanced Front Air Bags are designed to deflate immediately after deployment. • Cut off fuel to the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • As the air bags deflate, you may see some smoke-like Maintaining Your Air Bag System particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag WARNING! inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, • Modifications to any part of the air bag system could cause it to fail when you need it. You could rinse the area with cool water.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 There are different sizes and types of restraints for NOTE: children from newborn size to the child almost large • For additional information, refer to www.seatcheck.org or enough for an adult safety belt. Always check the child call 1–866–SEATCHECK. Canadian residents should refer seat Owner’s Manual to make sure you have the correct to Transport Canada’s website for additional information: seat for your child.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicle’s seat belt alone: 1. Can the child sit all the way back against the back of the vehicle seat? 2.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints — Quad Cab®/Crew Cab Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Recommendations For Attaching Child Restraints — Standard Cab, Mega Cab® Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 LATCH Positions For Installing Child Restraints In This Vehicle 2 Quad Cab®/Crew Cab Full Bench Lower Anchorage Symbol 2 anchorages per seating position Lower Anchorage Symbol 2 anchorages per seating Top Tether Anchorage Symbol position Standard Cab Top Tether Anchorage Symbol
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab®/Mega Cab®/Crew Cab Split Bench Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Quad Cab®/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No Never “share” a LATCH anchorage with two or more child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Mega Cab®/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Locating The LATCH Anchorages In addition, Regular Cab models have tether strap anchorages behind the front center and right seats. Quad Cab®, Mega Cab® and Crew Cab models have tether strap anchorages located behind each of the rear seats.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH — Standard Cab/Quad Cab®/Crew Cab Full Bench Do not install a child restraint in the center position using the LATCH system. Use the seat belt and tether anchor to install a child seat in the center seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Center Seat LATCH — Quad Cab®/Mega Cab®/Crew Cab Split Bench To Install A LATCH-compatible Child Restraint 1. If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, do not install a child seat in that outboard 2. position.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 WARNING! • Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • Child restraint anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle Quad Cab®/Mega Cab®/Crew Cab Standard Cab
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Quad Cab®/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Yes Always us
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab®/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you will position. For some second row seats, you may need to hear a clicking sound.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by 2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child pulling back and forth on the child seat at the belt restraint. Do not twist the belt webbing in the belt path. It should not move more than 1 inch (25.4 mm) path. in any direction. Any seat belt system will loosen with time, so check the 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25 mm) in any direction. If the belt still cannot be tightened after you shorten the buckle, disconnect the latch plate from the buckle, turn the buckle around one half turn, and insert the latch plate into the buckle again.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head restraint and between its posts. 3. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 WARNING! Never place a rear facing infant seat in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. Mega Cab® Tether Strap Mounting Quad Cab® or Crew Cab Trucks: The top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Right or Left Outboard Seats: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. Tether Strap Loop With Center Head Restraint In Raised Position Head Restraint In Raised Position 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 3. Pass the tether strap hook under the head restraint 4. Attach the hook to the center tether strap loop (see behind the child seat, though the tether strap loop diagram). Tighten the tether strap according to the behind the seat and over to the center tether strap child seat manufacturer’s instructions. loop.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats. Center Seat: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. Tether Strap Loop With Head Restraint In Raised Position 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 3. Pass the tether strap hook under the head restraint 4. Attach the hook to the outboard tether strap loop (see behind the child seat, though the tether strap loop diagram). Tighten the tether strap according to the behind the seat and over to the right or left outboard child seat manufacturer’s instructions. tether strap loop.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Three Child Restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above. 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3. Place a child restraint on the center rear seat. Route the tether strap following the directions for the center seating position, above. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! • Use the appropriate transmission gear to prevent engine lugging. Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. • Observe vehicle oil pressure and temperature indicators. • Check the coolant and oil levels frequently. NOTE: A new engine may consume some oil during its • Vary throttle position at highway speeds when carryfirst few thousand miles (kilometers) of operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 SAFETY TIPS Exhaust Gas Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .117 ▫ Automatic Dimming Mirror — If Equipped . . .117 ▫ Automatic Dimming Mirror With Rear View Camera Display — If Equipped . . . . . . . . . . .123 ▫ “Slide-On-Rod” Features Of Sun Visor — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .128 ▫ Trailer Towing Mirrors — If Equipped . . . . . .128 䡵 SEATS . . . . . . .
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ 40-20-40 Front Bench Seat — If Equipped . . . .137 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .137 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .139 ▫ Programming The Memory Feature . . . . . . . . .140 ▫ Linking And Unlinking The Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . . .141 ▫ Memory Position Recall . . . . . . . . . . . . . . . . .142 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . . .143 䡵 LIGHTS . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . .155 䡵 HEATED STEERING WHEEL — IF EQUIPPED . .163 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .155 䡵 ELECTRONIC SPEED CONTROL . . . . . . . . . . .164 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . .156 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .165 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .156 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 POWER INVERTER — IF EQUIPPED . . . . . . . .174 ▫ Seatback Storage . . . . . . . . . . . . . . . . . . . . . .182 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .175 ▫ Storage (Regular Cab) . . . . . . . . . . . . . . . . . .182 ▫ Front Seat Cupholders (40–20–40 Seats) . . . . . .175 ▫ Storage and Seats (Crew Cab) . . . . . . . . . . . . .183 ▫ Front Instrument Panel Cupholders — Floor Storage Bin . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. NOTE: • The Automatic Dimming Mirror feature is disabled when the vehicle is in reverse gear to improve rear view viewing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Assist Call 9-1-1 Call The rear view mirror contains an ASSIST push button 1. Press the 9-1-1 Call button on the Rearview Mirror. which automatically connects the vehicle occupants to NOTE: In case the 9-1-1 Call button is pushed in error, one of several predefined locations for immediate supthere will be a 10 second delay before the 9-1-1 Call port: system initiates a call to a 9-1-1 operator.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit the following important vehicle information to a 9-1-1 operator: • Indication that the occupant placed a 9-1-1 Call. • The vehicle brand. • The last known GPS coordinates of the vehicle. 4. You should be able to speak with the 9-1-1 operator through the vehicle audio system to determine if additional help is needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING! (Continued) • The 9-1-1 Call system is embedded into the vehicle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical system. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid interference that can cause the 9-1-1 Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Ignoring the Rearview Mirror light could mean you will not have 9-1-1 Call services. If the Rearview Mirror light is illuminated, have an authorized dealer service the 9-1-1 Call system immediately. • The ORC turns on the air bag Warning Light on the instrument panel if a malfunction in any part of the system is detected. If the air bag Warning Light is illuminated, have an authorized dealer service the ORC system immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 NOTE: Never place anything on or near the vehicle’s wireless and GPS antennas. You could prevent wireless and GPS signal reception, which can prevent your vehicle from placing an emergency call. Wireless and GPS signal reception is required for the 9-1-1 Call system to function properly. Automatic Dimming Mirror With Rear View Camera Display — If Equipped A single ball joint mirror is provided in the vehicle.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. 3 Folding Mirror CAUTION! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Power Mirror Controls Location The power mirror controls consist of mirror select buttons and a four-way mirror control switch.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move Power Mirror Controls 1 — Mirror Select Buttons 2 — Four-Way Mirror Control Switch To adjust a mirror, press either the L (left) or R (right) button to select the mirror that you want to adjust.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information. 3 Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Slide-On-Rod” Features Of Sun Visor — If Equipped Trailer Towing Mirrors — If Equipped The sun visor “Slide-On-Rod” feature allows for additional These mirrors are designed with an adjustable mirror flexibility in positioning the visor to block out the sun. head to provide a greater vision range when towing To use the “Slide-On-Rod” feature, rotate the sun visor extra-wide loads.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: Fold the trailer towing mirrors rearward prior to SEATS entering an automated car wash. Seats are a part of the Occupant Restraint System of the A small blindspot mirror is located next to main mirror vehicle. and can be adjusted separately. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Power Seat — If Equipped Some models may be equipped with an eight-way power driver’s seat. The power seat switches are located on the outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the movement of the seat cushion and the seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Passenger’s Power Seat — If Equipped Some models are equipped with a six-way power passenger seat. The power seat switch is located on the outboard side of the seat. The switch is used to control the movement of the seat and seat cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch, the front of the seat cushion will move in the direction of the switch. Release the switch when you have reached the desired position. 3 Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped Rear Heated Seats On some models, the front and rear seats may be On some models, the two outboard seats are equipped equipped with heaters located in the seat cushions. with heated seats. The heated seat switches for these seats are located on the rear of the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: Ventilated Seats — If Equipped • Once a heat setting is selected, heat will be felt within On some models, both the driver and passenger seats are ventilated. Located in the seat cushion is a small fan that two to five minutes. draws air from the passenger compartment and pulls the air • The engine must be running for the heated seats to through fine perforations in the seat cover to help keep the operate.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the switch will be illuminated. When LOW speed is selected one light will be illuminated. NOTE: The engine must be running for the ventilated seats to operate. Vehicles Equipped With Remote Start On models equipped with remote start, the drivers ventilated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. 40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion. To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach the desired position, release the handle. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, adjustable pedals (if equipped) and a set of desired radio station presets. Your Remote Keyless Entry (RKE) transmitter can also be programmed to recall the same positions when the UNLOCK button is pressed.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The memory seat buttons are located on the outboard Programming The Memory Feature side of the drivers seat cushion. NOTE: To create a new memory profile, perform the following: Vehicles Equipped With Keyless Enter-N-Go 1. Without pressing the brake pedal, push the ENGINE START/STOP button and cycle the ignition to the ON/RUN position (do not start the engine). 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Vehicles Not Equipped With Keyless Enter-N-Go NOTE: 1. Insert the ignition Key Fob, and turn the ignition • Memory profiles can be set without the vehicle in switch to the ON/RUN position. PARK, but the vehicle must be in PARK to recall a memory profile. 2.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Before programming your RKE transmitters you 3. Once the profile has been recalled, press and release must select the “Memory To FOB” feature through the the SET (S) button on the memory switch, then press and release button (1) or (2) accordingly. “Memory Uconnect® system screen. Refer to “Customer- ProgramProfile Set” (1 or 2) will display in the instrument mable Features — Uconnect® Access 8.4 Settings ” in cluster on vehicles equipped with the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 A recall can be cancelled by pressing any of the MEMORY buttons during a recall (S, 1, or 2). When a • To recall the memory settings for driver one using the recall is cancelled, the driver’s seat, and the pedals stop memory switch, press MEMORY button number 1 on moving. A delay of one second will occur before another the memory switch. recall can be selected.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Hood Release 2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. Safety Latch Location (1500 Series Shown) CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the AUTO position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 When the system is on, the Headlight Delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the OFF position. To turn the automatic headlights off, turn the headlight switch out of the AUTO position. Daytime Running Lights (DRL) — If Equipped The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight delay can be cancelled by either turning the NOTE: headlight switch on then off, or by turning the ignition ON. • Automatic High Beam Headlamp Control can be The headlight delay time is programmable on vehicles turned on or off using the Uconnect® System, refer to equipped with an Electronic Vehicle Information Center “Uconnect® Settings” in “Understanding Your Instru(EVIC) or a Uconnect® system screen.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To Activate To Deactivate 1. Select “Automatic High Beams — ON” through the Perform either of the following steps to deactivate the EVIC. Refer to “Electronic Vehicle Information Center Automatic High Beam system. (EVIC)/Customer-Programmable Features” in “Un1. Select “Automatic High Beams — OFF” through the derstanding Your Instrument Panel” for further inforEVIC. Refer to “Electronic Vehicle Information Center mation.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parking Lights And Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the O (Off) position. Fog Lights — If Equipped The fog lights are turned on by rotating the headlight switch to the parking light or headlight position and pushing in the headlight rotary control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Lights-On Reminder Interior Lights If the headlights, parking lights, or cargo lights are left on Courtesy and dome lights are turned on when the front after the ignition is turned OFF, a chime will sound when doors are opened, when the dimmer control (rotating the driver’s door is opened. wheel on the bottom of the switch) is rotated to the far right detent position.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE rotating the control to the right until you hear a click. This door is opened, when the dimmer control is rotated to the feature is termed the “Parade” mode and is useful when courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry headlights are required during the day. (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Ambient Light The overhead console is equipped with an ambient light feature. This light casts illumination for improved visibility of the floor console area. 3 Rear Passenger Courtesy/Reading Light NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cargo lights will also turn on for approximately 30 The cargo lights are turned on by pressing on the cargo seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry feature. button. Multifunction Lever Cargo Light The multifunction lever is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-To-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High/Low Beam Switch WINDSHIELD WIPERS AND WASHERS Push the multifunction lever toward the instrument Windshield Wipers panel to switch the headlights to high beam. Pulling the The wipers and washers are operated by a switch in the multifunction lever back toward the steering wheel will multifunction lever. Turn the end of the handle to select turn the low beams back on, or shut the high beams off. the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Windshield Wiper Operation Windshield Washers Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation. To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the The Rain Sensing feature will not operate when the following conditions: wiper switch is in the low or high-speed position.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Remote Start Mode Inhibit — On vehicles equipped with Remote Starting system, Rain Sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the RUN position, rain sensing wiper operation can resume, if it has been selected, and no other inhibit conditions (mentioned previously) exist.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! The adjustable pedal switch is located to the left side of the steering column. Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted with the ignition OFF. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 HEATED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 30 to 80 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The Electronic Speed Control buttons are located on the right side of the steering wheel. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the U.S. Speed (mph) vehicle will deactivate the Electronic Speed Control with• Pressing the RES (+) button once will result in a 1 mph out erasing the set speed memory. increase in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • If the button is continually pressed, the set speed will continue to decrease until the button is released, then When the Electronic Speed Control is set, you can dethe new set speed will be established. crease speed by pushing the SET (-) button. The speed decrement shown is dependant on the speed To Accelerate For Passing To Decrease Speed of U.S. (mph) or Metric (km/h) units: U.S. Speed (mph) Press the accelerator as you would normally.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. OVERHEAD CONSOLE — IF EQUIPPED The overhead console is located on the headliner above the rearview mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC,” together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON/RUN or ACC positions for the outlet to provide power.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 3 Power Outlets — Center Stack • Center console when equipped with bucket seats. Power Outlet — Center Console • Inside the upper lid of the center storage compartment — if equipped.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outlet — Upper Lid Power Outlet — Rear Center Console • Rear of the center console storage compartment — The key symbol indicates that this outlet can supply power Quad Cab® or Crew Cab. when the key is in the ON/RUN or ACC positions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 WARNING! CAUTION! (Continued) To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. CUPHOLDERS Front Seat Cupholders (40–20–40 Seats) Power Inverter Outlet The cupholders are located on the backside of the center To turn on the power outlet, simply plug in the device. portion of the front seat (20).
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Storage Bin Rear Cupholder — Crew Cab Crew Cab vehicles are equipped with rear cupholders For vehicles equipped with bucket seats two cupholders located in the center armrest. are located in the floor storage bin. Crew Cab Rear Armrest Cupholder Front Cupholders For Bucket Seats Crew Cab vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 3 Rear Cup Wells STORAGE Glove Compartment The glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove compartment push upward on To open the lower glove compartment, pull on the handle the handle release. The glove compartment door will to release the latch and lower the glove compartment automatically open. door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Door Storage Rear Door Storage — Crew Cab Front Door Storage — If Equipped Storage compartments are located in both the driver and passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 3 Upper Storage Compartment Lower Storage Bin With the upper lid closed, pull on the lower handle to open the lower storage bin. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seatback Storage Storage (Regular Cab) Located in the back of both the driver and passenger The storage bin is located behind the front seats and runs front seats are pockets that can be used for storage. the length of the cab.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Crew Cab Storage CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .189 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .190 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . . .191 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .192 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . .205 ▫ Electronic Vehicle Information Center (EVIC) Messages . . . . . . . . . . . . . . . . . . . . . . . . . . .
188 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .259 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .260 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . . .260 䡵 RADIO OPERATION AND MOBILE PHONES . .261 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . .261 ▫ Manual Climate Controls Without Touchscreen — If Equipped . . . . . . . . . . . . . .261 ▫ Manual Climate Controls With Touchscreen — If Equipped . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 189 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 6 — — — — — — Headlight Switch Instrument Cluster Radio Hazard Switch Upper Glove Compartment Lower Glove Compartment 7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank 10 — Instrument Panel Drawer 11 — Climate Controls 12 — Power Outlet/Cigar Lighter 13 — Gear Selector/Transfer Case Position Switch — If Equipped 14 — Ignition Switch 15 — Hood Release 16 — Parking Brake Release
190 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 191 INSTRUMENT CLUSTER — PREMIUM 4
192 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Tachometer The tachometer indicates engine speed in Revolutions Per Minute (RPM x 1000). CAUTION! Do not operate the engine with the tachometer pointer at high RPM for extended periods. Engine operation over 3200 RPM (Redline) can result in significant damage that will not be covered under the New Vehicle Limited Warranty. 2. Anti-Lock Brake (ABS) Light This light monitors the Anti-lock Brake System (ABS).
UNDERSTANDING YOUR INSTRUMENT PANEL 193 3. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic (OBDII) system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing, the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
194 UNDERSTANDING YOUR INSTRUMENT PANEL If the pointer moves to either extreme left or right and remains there during normal driving, the electrical sysThe arrow will flash with the exterior turn tem should be serviced. signal when the turn signal lever is operated. NOTE: The voltmeter may show a gauge fluctuation at various engine temperatures. This cycling operation is caused by the post-heat cycle of the intake manifold NOTE: heater system.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 9. Air Bag Warning Light 11. Speedometer This light will turn on for four to eight seconds The speedometer shows the vehicle speed in miles per as a bulb check when the ignition switch is first hour and/or kilometers per hour (mph/km/h). turned to ON/RUN. If the light is either not on 12.
198 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Vehicle Security Light — If Equipped This light will flash at a fast rate for approximately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 16.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
200 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The highest available transmission gear is displayed in the lower right corner of the Electronic Vehicle This indicator will illuminate when the front Information Center (EVIC) whenever the Electronic fog lights are on. Range Select (ERS) feature is active. Use the +/- selector on the shift lever to activate ERS. Refer to “Automatic 18.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 22. TOW/HAUL The TOW HAUL button is located on the center stack upper switch bank. This light will illuminate when TOW HAUL mode is selected. 23. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running.
202 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authoThis telltale is on when the Electric Power rized dealer for service as soon as possible. If the light is Steering is not operating and needs service. flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may 27.
204 UNDERSTANDING YOUR INSTRUMENT PANEL 29. Air Suspension Off-Road 1 Indicator Lamp – If Equipped rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. This light will illuminate when the air suspension system is set to the Off-Road 1 setting.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 33. 4WD Indicator Light — If Equipped This light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) For further information on four-wheel drive operation and proper use, refer to “Four-Wheel Drive Operation — If Equipped” in “Starting And Operating”.
206 UNDERSTANDING YOUR INSTRUMENT PANEL This system allows the driver to select a variety of useful The system allows the driver to select information by information by pressing the switches mounted on the pressing the following buttons mounted on the steering wheel: steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 • UP Arrow Button Press and release the UP arrow button to scroll upward through the main menu and submenus (Fuel Economy, Trip A, Trip B, Audio, Stored Messages, Screen Set Up). • DOWN Arrow Button • SELECT/RIGHT Arrow Button Press and release the SELECT/RIGHT arrow button to access/select the information screens or sub-menu screens of a main menu item.
208 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays — 3.5” Display The EVIC displays are located in the center portion of the cluster and consists of seven sections: 1. Compass Display Displays the current direction. For further information, refer to “Compass Settings” under “Customer Programmable Features — Uconnect® 5.0/8.4 Settings”. 2. Temperature Display Displays the temperature in degrees Celsius or degrees Fahrenheit. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 4. EVIC White Telltales • Electronic Speed Control Ready This light will turn on when the electronic speed control is ON. For further information, refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle.” • Electronic Speed Control SET This light will turn on when the electronic speed control is SET. For further information, refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle.
210 UNDERSTANDING YOUR INSTRUMENT PANEL • Low Coolant Level Indicator This telltale will turn on to indicate the vehicle coolant level is low. WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • Transmission Temperature Warning Telltale This telltale indicates that the transmission fluid temperature is running hot.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • Service Stop/Start System Telltale — If Equipped • Wait To Start Light — Diesel Only The “Wait To Start” telltale will illuminate for apThis telltale will turn on to indicate that the proximately two seconds when the ignition is turned Stop/Start is Unavailable, service Stop/Start to the RUN position. It’s duration may be longer based on system. colder operating conditions. Vehicle will not initiate start • Loose Fuel Filler Cap until telltale is out.
212 UNDERSTANDING YOUR INSTRUMENT PANEL • Charging System Light 6. EVIC Red Telltales This light shows the status of the electrical charg• Door Ajar ing system. If the light stays on or comes on while This light will turn on to indicate that one or driving, turn off some of the vehicle’s non-essential more doors may be ajar. electrical devices or increase engine speed (if at idle).
UNDERSTANDING YOUR INSTRUMENT PANEL 213 If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
214 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Audio/Phone Information And Sub-menu Information • Unstored Messages Whenever there are sub-menus available, the position This message type is displayed indefinitely or until the within the sub-menu is shown here. condition that activated the message is cleared. Examples The main display area will normally display the main menu of this message type are “Turn Signal On” (if a turn signal or the screens of a selected feature of the main menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Electronic Vehicle Information Center (EVIC) Displays — 7” Display The EVIC displays are located in the center portion of the cluster and consists of eight sections: 1. Main Screen — The inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings and white for on demand information. 2.
216 UNDERSTANDING YOUR INSTRUMENT PANEL 8. 4WD Status 9. Selectable Gauge 2 10. Selectable Gauge 1 11. Selectable Gauge 1 The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 • Five Second Unstored Messages When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. An example of this message type is “Automatic High Beams On”. • Low Coolant Level Indicator This telltale will turn on to indicate the vehicle coolant level is low.
218 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • Air Suspension Payload Protection Telltale — If Equipped • Service Stop/Start System Telltale — If Equipped This telltale will turn on to indicate that the Stop/Start is Unavailable, service Stop/Start system.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 • Hill Decent Control (HDC) — If Equipped EVIC Red Telltales The symbol indicates the status of the Hill De- This area will show reconfigurable red telltales. These cent Control (HDC) feature. The lamp will be on telltales include: solid when HDC is armed. HDC can only be • Door Ajar armed when the transfer case is in the “4WD This light will turn on to indicate that one or Low” position and the vehicle speed is less then 30 mph more doors may be ajar. (48 km/h).
220 UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. • Charging System Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
UNDERSTANDING YOUR INSTRUMENT PANEL 221 • Engine Temperature Warning Light • Electric Power Steering Malfunction Warning Light This light warns of an overheated engine condiThis telltale is on when the Electric Power Steering is not operating and needs service. tion. As temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold.
222 UNDERSTANDING YOUR INSTRUMENT PANEL displayed. Press the LEFT or SELECT/RIGHT arrow button to scroll through the following information subPress and release the UP or DOWN arrow buttons until menus: the desired Selectable Menu icon is highlighted in the EVIC. Air Suspension – If Equipped EVIC Selectable Menu Items Digital Speedometer Transmission Temperature – Automatic Transmission Only Press and release the UP or DOWN arrow Oil Temp button until the Digital display icon is highlighted in the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Tire Pressure Information System (3500 Series Heavy Trip A Duty Ram Trucks) Press and release the UP or DOWN arrow Press and release the UP or DOWN arrow button until button until the Trip A icon is highlighted in “Tire Pressure” is highlighted in the EVIC. Press and the EVIC.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Trip B Fuel Economy Press and release Up & Down arrow button until the Trip B icon is highlighted in the EVIC. The Trip B information will display the following: Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Press the SELECT/RIGHT arrow button and the next Screen Setup sub-menu. The Screen Setup feature allows screen will display the following trailer trip information: you to change what information is displayed in the instrument cluster as well as the location that information • Trailer Trip is displayed. • Trailer Brake Screen Setup Driver Selectable Items Audio Odometer • 000 Press and release the UP or DOWN arrow button until the Audio display icon is high- • 000.
226 UNDERSTANDING YOUR INSTRUMENT PANEL • Time • Oil Temp • Range To Empty (RTE) • Time • Average MPG • Range To Empty (RTE) • Current MPG • Average MPG • Trip A • Current MPG • Trip B • Trip A • Trailer Trip (distance only) • Trip B • Trailer Brake Gain • Trailer Trip (distance only) Upper Right • Trailer Brake Gain • None Lower Left • Compass (default setting) • None (default setting) • Outside Temp • Compass • Trans Temp • Outside Temp
UNDERSTANDING YOUR INSTRUMENT PANEL 227 • Trans Temp • Trans Temp • Oil Temp • Oil Temp • Time • Time • Range • Range • AVG MPG • AVG MPG • Current MPG • Current MPG • Trailer Brake Gain • Trailer Brake Gain Lower Right Restore To Defaults (Restores All Settings To Default Settings) • None (default setting) • Compass • Outside Temp • Cancel • Okay 4
228 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Life Reset 4. Press and hold the RIGHT arrow button for one second to access the ”Oil Life Reset” screen. Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message 5. Press and release the DOWN arrow button to select will flash in the EVIC display for approximately 10 “Yes”, then press and release the Right arrow button to seconds after a single chime has sounded, to indicate the select reset of the Oil Life.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 5. Press and release the DOWN arrow button to select • Washer Fluid Low “Yes”, then press and release the Right arrow button to • Oil Pressure Low select reset of the Oil Life. • Oil Change Due 6. Press and release the Up arrow button to exit the EVIC • Fuel Low screen. NOTE: If the indicator message illuminates when you • Service Antilock Brake System start the vehicle, the oil change indicator system did not • Service Electronic Throttle Control reset.
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Brake Fluid Low • Remote Start Active Push Start Button • Service Electronic Braking System • Remote Start Aborted Fuel Low • Engine Temperature Hot • Remote Start Aborted Too Cold • Battery Voltage Low • Remote Start Aborted Door Open • Service Electronic Throttle Control • Remote Start Aborted Hood Open • Lights On • Remote Start Aborted Trunk Open • Right Turn Signal Light Out • Remote Start Aborted Time Expired • Left Turn Signal Light Out • Remo
UNDERSTANDING YOUR INSTRUMENT PANEL 231 • Door Open • Transmission Too cold Idle with Engine On • Doors Open • Washer Fluid Low • Gear Not Available The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left.
232 UNDERSTANDING YOUR INSTRUMENT PANEL For vehicles equipped with a 7” EVIC screen and not Language equipped with a Uconnect® 8.4 radio. When in this display you may select one of six languages Personal Settings allows the driver to set and recall for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the UP or features when the transmission is in PARK.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Nav-Turn By Turn — If Equipped selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. Refer to “Rear Park Assist System” in “Understanding The Features Of Your Vehicle” for system function and operating information.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Wipers — If Equipped Headlamp Off Delay When ON is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Headlamps With Wipers Daytime Running Lights When this feature is selected and the HEADLIGHT switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature.
236 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Lock Doors Horn With Remote Start When this feature is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Remote Unlock Sequence When Unlock Driver Door Only On 1st Press is selected, only the driver’s door will unlock on the first press of the RKE transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When Unlock All Doors On 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Start Comfort Sys. When this feature is selected and the remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the key is turned to RUN.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Trailer Select Trailer Name When this feature is selected, the Trailer Type can be selected between “Trailer 1”, “Trailer 2”, “Trailer 3” and “Trailer 4”. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. When this feature is selected, the Trailer name can be selected from 16 names.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Hard-Keys Soft-Keys Hard-Keys are located below the Uconnect® system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), press the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
UNDERSTANDING YOUR INSTRUMENT PANEL 241 When making a selection, press the soft-key to enter the desired mode. Once in the desired mode, press and release the preferred setting until a check-mark appears next to the setting, showing that setting has been selected. Once the setting is complete, either press the “Back Arrow” soft-key or the BACK hard-key to return to the previous menu or press the “X” soft-key to close out of the settings screen.
242 UNDERSTANDING YOUR INSTRUMENT PANEL language soft-key until a check-mark appears next to the • Touchscreen Beep language, showing that setting has been selected. Touch When in this display, you may turn on or shut off the the back arrow soft-key to return to the previous menu. sound heard when a touchscreen button (soft-key) is • Units pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 • Fuel Saver Display In Cluster • Set Time Hours The “ECO” message is located in the instrument cluster display, this message can be turned on or off. To make your selection, touch the “Fuel Saver Display” soft-key, until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. When in this display, you may adjust the hours. The “Sync with GPS Time” soft-key must be unchecked.
244 UNDERSTANDING YOUR INSTRUMENT PANEL • Time Format touch and release the “Sound Only” or the “Sounds and Display” soft-key. Then touch the back arrow soft-key. When in this display, you may select the time format Refer to “ParkSense® Rear Park Assist” in “Understanddisplay setting. Touch the “Time Format” soft-key until a ing The Features Of Your Vehicle” for system function check-mark appears next to the 12hrs or 24hrs setting, and operating information. showing that setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 • ParkView® Backup Camera the “ParkView® Backup Camera Delay” soft-key, until a check-mark appears next to the setting, indicating that Your vehicle may be equipped with the ParkView® Rear the setting had been selected. Touch the back arrow Back Up Camera that allows you to see an on-screen soft-key to return to the previous menu. image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE.
246 UNDERSTANDING YOUR INSTRUMENT PANEL • ParkView® Backup Camera Fixed Guidelines Your vehicle may be equipped with the ParkView® Rear Back Up Camera Fixed Guidelines that allows you to see Fixed Guidelines over the ParkView Back up Camera display whenever the shift lever is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds, this note will disappear.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 • ParkSense® Rear Park Assist Chime Volume • Hill Start Assist — If Equipped When this feature is selected, the Hill Start Assist (HSA) system is active. Refer to “Electronic Brake Control System” in “Starting And Operating” for system function and operating information.
248 UNDERSTANDING YOUR INSTRUMENT PANEL The headlights will also turn off when the wipers are turned off, if they were turned on by this feature. To After pressing the “Lights” soft-key the following setmake your selection, touch the “Headlights With Wipers” tings will be available: soft-key, until a check-mark appears next to the setting, • Headlight Illumination On Approach showing that setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 • Daytime Running Lights — If Equipped Doors & Locks When this feature is selected, the headlights will turn on whenever the engine is running. To make your selection, touch the “Daytime Running Lights” soft-key, until a check-mark appears next to the setting, showing that the setting has been selected. Touch the back arrow soft-key to return to the previous menu.
250 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Remote Start When this feature is selected, the horn will sound when the remote start is activated. To make your selection, touch the “Sound Horn With Remote Start” soft-key, until a check-mark appears next to the setting, showing that the setting has been selected. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 soft-key to return to the previous menu. Refer to “Keyless Auto-On Comfort & Remote Start Enter-N-Go™” in “Things To Know Before Starting Your After pressing the “Auto-On Comfort & Remote Start” Vehicle”. soft-key the following settings will be available: • Memory To FOB — If Equipped • Horn With Remote Start This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
252 UNDERSTANDING YOUR INSTRUMENT PANEL turn on. To make your selection, touch the “Auto Heated • Headlight Off Delay Seats” soft-key, until a check-mark appears next to the When this feature is selected, the driver can choose to setting, showing that the setting has been selected. Touch have the headlights remain on for 0, 30, 60, or 90 seconds the back arrow soft-key to return to the previous menu. when exiting the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 NOTE: Keep magnetic materials, such as iPod’s®, Mobile Phones, Laptops and Radar Detectors, away from the top of the instrument panel where the compass module is located. These materials can cause interference with the compass sensor, and it may give false readings. • Perform Compass Calibration Touch the “Calibration” soft-key to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass.
254 UNDERSTANDING YOUR INSTRUMENT PANEL • Equalizer • Surround Sound — If Equipped When in this display you may adjust the Bass, Mid and Treble settings. Adjust the settings with the “+” and “–” soft-keys or by selecting any point on the scale between the “+” and “–” soft-keys. Then touch the back arrow soft-key. This feature provides simulated surround sound mode. To make your selection, touch the “Surround Sound” soft-key, select On or Off followed by pressing the back arrow soft-key.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Phone/Bluetooth® • Flash Lights With Remote Lower After touching the “Phone/Bluetooth®” soft-key the When this feature is selected, the front and rear turn following settings will be available: signals will flash when the RKE transmitter REMOTE LOWER button is pressed twice. This feature may be • Paired Devices selected with or without the Sound Horn on Lower This feature shows which phones are paired to the feature selected.
256 UNDERSTANDING YOUR INSTRUMENT PANEL appears next to the feature showing the system has been • Wheel Alignment Mode activated or the check-mark is removed showing the Before performing a wheel alignment this mode must be system has been deactivated. enabled. Refer to your authorized dealer for further • Tire Jack Mode information. When this feature is selected the air suspension system is disabled to assist with changing a spare tire.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 • Trailer Brake Type SiriusXM Setup When this feature is selected, the Trailer Brake Type can be changed between “Light Electric,” “Heavy Electric,” “Light EOH” and “Heavy EOH.”. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. Refer to “Integrated Trailer Brake Module” in “Starting And Operating.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Touch the “Subscription Info” soft-key to access the iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions Subscription Information screen. may not fully support the iPod® control features. Please Write down the SIRIUS ID numbers for your receiver. To visit Apple’s website for software updates.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 The button located in the center of the right hand control will switch modes to Radio, CD or other valid audio sources. The left hand control is a rocker type switch with a pushbutton in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
260 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player 3. Do not apply paper or tape to the disc; avoid scratching the disc. Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once 4. Do not use solvents such as benzene, thinner, cleaners, will go to the beginning of the current track or to the or anti-static sprays. beginning of the previous track if it is within eight 5. Store the disc in its case after playing.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 RADIO OPERATION AND MOBILE PHONES CLIMATE CONTROLS Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the OFF position.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. MAX A/C For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recirculated.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Panel Mode Bi-Level Mode Air is directed through the panel and floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Mix Mode Recirculation Control Air is directed through the floor, defrost and side Press the Recirculation Control button to window demist outlets. This setting works best in choose between outside air intake or recirculacold or snowy conditions that require extra heat at the tion of the air inside the vehicle. A LED will windshield. This setting is good for maintaining comfort, illuminate when you are in Recirculation while reducing moisture on the windshield.
266 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. For maximum defogging, select the outside air position. Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired tem• The A/C can be deselected manually without disturb- perature.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Manual Climate Controls With Touchscreen — If Equipped Soft-Keys Soft-keys are accessible on the radio touchscreen. Hard-Keys The hard-keys are located below the radio touchscreen.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both Hard-Keys And 4. Front Defrost Button Soft-Keys) Press and release to change the current airflow setting to 1. MAX A/C Button Defrost mode. The indicator illuminates when this feaPress and release to toggle between MAX A/C and the ture is ON. Air comes from the windshield and side prior settings. The soft-key illuminates when MAX A/C is window demist outlets. When the defrost button is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
270 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • Mix Mode Air comes from the floor, defrost and side window demister outlets. This mode works best in cold or snowy conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 8. Climate Control OFF Button Recirculation Control Press and release this button to turn the Climate Control ON/OFF. When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, 9. Temperature Control Down Button you may wish to recirculate interior air by pressing the RECIRCULATION control button. Push the button for cooler temperature settings.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Climate Controls With Touchscreen — If Equipped Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Hard-Keys The hard-keys are located below the Uconnect® screen. Uconnect® 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Button Descriptions (Applies To Both Hard-Keys And Soft-Keys) 1. MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. 2. A/C Button Uconnect® 8.4 Automatic Temperature Controls — Soft-Keys Press and release to change the current setting, the indicator illuminates when A/C is ON.
274 UNDERSTANDING YOUR INSTRUMENT PANEL 4. AUTO Operation Button 6. Defrost Button Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Performing this function will cause the ATC to switch between manual mode and automatic modes. Refer to “Automatic Operation” for more information. Press and release this button to turn on the rear window defroster (if equipped) and the heated outside mirrors (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 275 CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. 7. Passenger Temperature Control Up Button Provides the passenger with independent temperature control.
276 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Blower Control 11. Modes Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation. The speeds can be selected using either hard-keys or soft-keys as follows: The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • Mix Mode Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. 13.
278 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Temperature Control (Uconnect® 5.0) NOTE: Press the temperature soft-key to regulate the tempera- • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts ture of the air inside the passenger compartment. Moving the temperature, mode, and blower speed to provide the temperature bar into the red area, indicates warmer comfort as quickly as possible. temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Recirculation Control of the windshield. On systems with Manual Climate Controls, the recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculation will be disabled automatically if this mode is selected. Attempting to use Recirculation while in this mode will cause the LED in the control button to blink and then turn off.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation Window Fogging and Frosting To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Refer to “Maintenance Procedures” in “Maintaining Your Vehicle” for proper coolant selection. Use of the air Recirculation mode during Winter months is not recommended because it may cause window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .288 ▫ Brake/Transmission Shift Interlock System . . .294 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .288 ▫ Six–Speed Automatic Transmission — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .294 ▫ Automatic Transmission . . . . . . . . . . . . . . . .289 ▫ Extreme Cold Weather (Below –20°F or −29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ If Engine Fails To Start . . . .
284 STARTING AND OPERATING ▫ Electronically Shifted Transfer Case 䡵 BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . (Four-Position Switch) — If Equipped . . . . . . .309 ▫ Four-Wheel Anti-Lock Brake System . . . . ▫ Shifting Procedure . . . . . . . . . . . . . . . . . . . . .314 ▫ Hydraulic Brake Assist. . . . . . . . . . . . . . 䡵 LIMITED-SLIP DIFFERENTIAL . . . . . . . . . . . . .316 䡵 ELECTRONIC BRAKE CONTROL SYSTEM 䡵 DRIVING ON SLIPPERY SURFACES . . . . . . . . .317 ▫ Anti-Lock Brake System (ABS) .
STARTING AND OPERATING 285 䡵 TIRE SAFETY INFORMATION . . . . . . . . . . . . .338 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .356 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .338 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .357 ▫ Tire Identification Number (TIN). . . . . . . . . . .341 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .357 ▫ Tire Terminology And Definitions . . . . . . . . . .343 ▫ Replacement Tires . . . . . . . . . .
286 STARTING AND OPERATING ▫ General Information . . . . . . . . . . . . . . . . . . .373 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .380 䡵 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . .373 ▫ Certification Label . . . . . . . . . . . . . . . . . . . .380 ▫ 5.7L Engines . . . . . . . . . . . . . . . . . . . . . . . . .373 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .382 ▫ 6.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . .374 ▫ Common Towing Definitions . . .
STARTING AND OPERATING 287 ▫ Over The Road Operation With Snowplow Attached. . . . . . . . . . . . . . . . . . . . . . . . . . . .402 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . .402 ▫ General Maintenance . . . . . . . . . . . . . . . . . . .402 䡵 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) . . . . . . . . . . . . . . . . . . .403 ▫ Towing This Vehicle Behind Another Vehicle . .403 ▫ Recreational Towing — Two-Wheel Drive Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
288 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING 289 Automatic Transmission If Engine Fails To Start Start the engine with the shift lever in the NEUTRAL or If the engine fails to start after you have followed the PARK. Apply the brake before shifting into any driving “Normal Starting” procedure, it may be flooded. Push range. the accelerator pedal all the way to the floor and hold it there while cranking the engine.
290 STARTING AND OPERATING WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
STARTING AND OPERATING 291 ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. Gasoline Engine Only The engine block heater cord is routed through the grille by the right front tow hook. It includes a removable cap that is secured by a tethered strap.
292 STARTING AND OPERATING CAUTION! (Continued) WARNING! (Continued) • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running.
STARTING AND OPERATING 293 WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
294 STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock system (BTSI) that holds the shift lever in PARK unless the brakes are applied. To shift the transmission out of PARK, the ignition switch must be turned to the ON/RUN position (engine running or not) and the brake pedal must be pressed. The shift lever is mounted on the right side of the steering column.
STARTING AND OPERATING 295 The transmission shift lever has only PARK, REVERSE, NEUTRAL, and DRIVE shift positions. Manual downshifts can be made using the Electronic Range Select (ERS) shift control (refer to “Electronic Range Select [ERS] Operation” in this section). Pressing the ERS (-/+) switches (on the shift lever) while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
296 STARTING AND OPERATING On four-wheel drive vehicles be sure that the transfer case is in a drive position. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released.
STARTING AND OPERATING 297 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
298 STARTING AND OPERATING • Release the shift lever and make sure it is fully seated in the PARK gate. • Look at the transmission gear position display and verify that it indicates the PARK position. • With brake pedal released, verify that the shift lever will not move out of PARK. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
STARTING AND OPERATING 299 If the transmission temperature exceeds normal operating limits, the powertrain controller will modify the This range should be used for most city and highway transmission shift schedule and expand the range of driving. It provides the smoothest upshifts and downtorque converter clutch engagement. This is done to shifts, and the best fuel economy. The transmission prevent transmission damage due to overheating.
300 STARTING AND OPERATING During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of the torque converter clutch is inhibited until the transmission fluid is warm (refer to the “Note” under “Torque Converter Clutch” in this section).
STARTING AND OPERATING 301 In the event of a momentary problem, the transmission If the transmission cannot be reset, authorized dealer can be reset to regain all forward gears by performing the service is required. following steps: Electronic Range Select (ERS) Operation 1. Stop the vehicle. The Electronic Range Select (ERS) shift control allows the 2. Shift the transmission into PARK. 3. Turn the ignition switch to the OFF position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6.
302 STARTING AND OPERATING WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. NOTE: To select the proper gear position for maximum deceleration (engine braking), simply press and hold the ERS (-) switch down. The transmission will shift to the range from which the vehicle can best be slowed down.
STARTING AND OPERATING 303 the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL The automatic transmission includes an electronically mode, transmission upshifts are delayed, and the transcontrolled Overdrive (fifth and sixth gears). The transmission will automatically downshift (for engine brakmission will automatically shift into Overdrive if the ing) during steady braking maneuvers.
304 STARTING AND OPERATING The “TOW/HAUL Indicator Light” will illuminate in the instrument cluster to indicate that TOW/HAUL mode has been activated. Pressing the switch a second time restores normal operation. Normal operation is always the default at engine start-up. If TOW/HAUL mode is desired, the switch must be pressed each time the engine is started. WARNING! Do not use the “TOW/HAUL” feature when driving in icy or slippery conditions.
STARTING AND OPERATING 305 control, when the transmission is sufficiently warm, Manually Shifted Transfer Case — If Equipped will demonstrate that the transmission is able to shift The transfer case provides four mode positions. into and out of Overdrive. • Two-wheel drive high range (2H) • If the vehicle has not been driven for several days, the first few seconds of operation after shifting the trans- • Four-wheel drive high range (4H) mission into gear may seem sluggish.
306 STARTING AND OPERATING this section for further information .The 4H and 4L positions are intended for loose, slippery road surfaces only. Driving in the 4H and 4L positions on dry, hard surfaced roads may cause increased tire wear and damage to the driveline components. The “Transfer Case Position Indicator Light” in the instrument cluster will alert the driver that the vehicle is in four-wheel drive and that the front and rear driveshafts are locked together.
STARTING AND OPERATING 307 WARNING! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear drive shafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
308 STARTING AND OPERATING CAUTION! Do not use 4L (Low) range when operating the vehicle on dry pavement. Driveline hardware damage can result. Shifting Procedure — Manually Shifted Transfer Case 2H To 4H 2H Or 4H To 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into NEUTRAL. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case NEUTRAL.
STARTING AND OPERATING 309 Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h).
310 STARTING AND OPERATING This electronically shifted transfer case provides four accomplished by rotating the 4WD Control Switch to the mode positions: desired position. Refer to “Shifting Procedure” in this section for specific shifting instructions. The 4WD LOCK • Two-wheel drive high range (2WD) and 4WD LOW positions are designed for loose, slippery road surfaces only.
STARTING AND OPERATING 311 Transfer Case Position Indicator Lights If One Or More Shift Conditions Are Not Met: The Transfer Case Position Indicator Lights (4WD and 1. The indicator light for the current position will remain 4LOW) are located in the instrument cluster and indicate ON. the current and desired transfer case selection. When you select a different transfer case position, the indicator 2. The newly selected position indicator light will continue to flash. lights will do the following: 3.
312 STARTING AND OPERATING The “SVC 4WD Warning Light” monitors the electronic shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it means that the four-wheel drive system is not functioning properly and that service is required. WARNING! Always engage the parking brake when powering down the vehicle if the “SVC 4WD Warning Light” is illuminated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury.
STARTING AND OPERATING 313 WARNING! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear drive shafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
314 STARTING AND OPERATING Shifting Procedure 2WD To 4WD LOCK NOTE: Rotate the 4WD control switch to the desired position. Shifts between 2WD and 4WD LOCK can be done with the vehicle stopped or in motion. With the vehicle in motion, the transfer case will engage/disengage faster if you momentarily release the accelerator pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the ON position with the engine either running or off.
STARTING AND OPERATING 315 2WD Or 4WD LOCK To 4WD LOW Alternate Procedure NOTE: When shifting into or out of 4WD LOW some 1. Bring the vehicle to a complete stop. gear noise may be heard. This noise is normal and is not 2. With the ignition switch in the ON position and the detrimental to the vehicle or occupants. engine running, shift the transmission into NEUTRAL. Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. You can use 3.
316 STARTING AND OPERATING • The ignition switch must be in the ON position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the ON position, the shift will not take place and no position indicator lights will be on or flashing. LIMITED-SLIP DIFFERENTIAL The limited-slip differential is especially helpful during slippery driving conditions.
STARTING AND OPERATING 317 DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
318 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle. and Warnings before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 319 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
320 STARTING AND OPERATING • Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. The standard power steering system will give you good This is due to the cold, thick fluid in the steering vehicle response and increased ease of maneuverability system. This noise should be considered normal, and it in tight spaces. The system will provide mechanical does not in any way damage the steering system. steering capability if power assist is lost.
STARTING AND OPERATING 321 Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
322 STARTING AND OPERATING The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the parking brake, firmly push the parking brake pedal fully. To release the parking brake, pull the parking brake release handle. When the parking brake is applied with the ignition switch ON, the “Brake Warning Light” in the instrument cluster will illuminate.
STARTING AND OPERATING 323 before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
324 STARTING AND OPERATING CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. This will be evident by increased pedal travel during application, greater pedal force required to slow or stop, and activation of the “Brake Warning Light” and the “ABS Warning Light” (if equipped) during brake use.
STARTING AND OPERATING 325 Four-Wheel Anti-Lock Brake System WARNING! The Four-Wheel Anti-Lock Brake System contains sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure.
326 STARTING AND OPERATING ABS Warning Light WARNING! (Continued) The ABS includes an amber warning light. When the light is illuminated, the ABS is not functioning. The system reverts to standard, non-anti-lock brakes. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 327 ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), Electronic Roll Mitigation (ERM), Hill Start Assist (HSA), Electronic Stability Control (ESC) and Trailer Sway Control (TSC). All of the systems work together to enhance vehicle stability and control in various driving conditions, and are commonly referred to as ESC.
328 STARTING AND OPERATING Traction Control System (TCS) — If Equipped Hill Start Assist (HSA) — If Equipped The TCS monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s), and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING 329 HSA Activation Criteria The following criteria must be met in order for HSA to activate: • Vehicle must be stopped • Vehicle must be on an approximate 7% or greater incline WARNING! There may be situations on minor hills with a loaded vehicle or while pulling a trailer where the system will not activate and slight rolling may occur, which could cause a collision with another vehicle or object. Always remember the driver is responsible for braking the vehicle.
330 STARTING AND OPERATING Towing And Hauling With HSA The HSA system does not know if your vehicle is loaded or towing a trailer unless the TOW/HAUL switch, located on the center stack, is selected. When activated, the “TOW/HAUL Indicator Light” will illuminate in the instrument cluster. Refer to “Automatic Transmission” in “Starting and Operating” for further information.
STARTING AND OPERATING 331 WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK or using the parking brake, it will roll down the incline and could collide with another vehicle, object or person, and cause serious or fatal injury. Always remember to use the parking brake while parking on a hill and that the driver is responsible for braking the vehicle. HSA Off Non-EVIC Equipped Vehicles 3.
332 STARTING AND OPERATING the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or HSA is a Customer Programmable Feature on an EVIC understeer condition. equipped vehicle. If you wish to turn off the HSA feature, refer to “Electronic Vehicle Information Center (EVIC)/ • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position.
STARTING AND OPERATING 333 WARNING! (Continued) from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. 4WD LOCK or 4WD AUTO, the ESC system will be in this mode. This mode should be used for almost all driving situations.
334 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving WARNING! (Continued) with snow chains or starting off in deep snow, sand or • Trailer Sway Control (TSC) is disabled when the gravel, it may be desirable to switch to the “Partial Off” ESC system is in the ⴖPartial Offⴖ mode. mode by pressing the “ESC Off” switch.
STARTING AND OPERATING 335 NOTE: The “ESC OFF” message will display and the audible chime will sound when the shift lever is placed into the PARK position from any other position and then moved out of the PARK position. This will occur even if the message was previously cleared. In this mode, ESC and TCS except for the “limited slip” feature described in the TCS section are turned off until the vehicle reaches a speed of 40 mph (64 km/h).
336 STARTING AND OPERATING The “ESC Activation/Malfunction Indicator Light” also flashes when TCS is active. If the “ESC Activation/ Malfunction Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. when the ignition switch is turned to the ON position.
STARTING AND OPERATING 337 The “ESC OFF Indicator Light” indicates the engine power may be reduced and you may feel the Electronic Stability Control (ESC) is partially brakes being applied to individual wheels to attempt to stop the trailer from swaying. TSC is disabled when the off. ESC system is in the “Partial Off” or “Full Off” modes. Trailer Sway Control (TSC) — If Equipped TSC is only active in the default “ESC On” mode.
338 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 339 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ...
340 STARTING AND OPERATING EXAMPLE: 10.
STARTING AND OPERATING 341 EXAMPLE: Load Identification: ⴖ....blank....
342 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S.
STARTING AND OPERATING 343 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
344 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. B-Pillar Location For Tire And Loading Information Placard 2.
STARTING AND OPERATING 345 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of 4. Cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires. XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and Loading trailer tongue weight (if applicable) should never exceed The vehicle maximum load on the tire must not exceed the weight referenced here.
346 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
STARTING AND OPERATING 347 5
348 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 349 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride.
350 STARTING AND OPERATING At least once a month: 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum infla• Check and adjust tire pressure with a good quality tion pressure molded into the tire sidewall. pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation.
STARTING AND OPERATING 351 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
352 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
STARTING AND OPERATING 353 If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode.
354 STARTING AND OPERATING rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT” in “What To Do Compact Spare Tire — If Equipped In Emergencies” for further information.
STARTING AND OPERATING 355 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life.
356 STARTING AND OPERATING vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel.
STARTING AND OPERATING 357 These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer replaced. to “Replacement Tires” in this section for further information.
358 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. “Tread Wear Indicators”. Refer to the Tire and Loading Information placard or the Vehicle Certification Label for the size designation of your tire.
STARTING AND OPERATING 359 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
360 STARTING AND OPERATING Please follow the table below for proper tire size, chain Use of traction devices require sufficient tire-to-body type, and axle recommendations: clearance. Follow these recommendations to guard against damage. TIRE CHAINS (TRACTION DEVICES) • Traction device must be of proper size for the tire, as recommended by the traction device manufacturer.
STARTING AND OPERATING 361 WARNING! CAUTION! (Continued) Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used.
362 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
STARTING AND OPERATING 363 NOTE: If your vehicle is equipped with a Tire Pressure Information System (TPIS): Dual Rear Wheels • The Tire Pressure Information System (TPIS) uses unique sensors in the inner rear wheels to help identify them from the outer rear wheels, because of this, the inner and outer wheel locations can’t be switched. Tire Rotation • After a tire rotation is completed, as shown below, the system can auto learn the locations of each sensor ID.
364 STARTING AND OPERATING CAUTION! 4500/5500 Dual Rear Tires may only have one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/Off road tire. • When replacing a flat, the spare tire may have to be remounted on the rim or installed at a different location to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the vehicle.
STARTING AND OPERATING 365 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure.
366 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable.
STARTING AND OPERATING 367 • Seasonal temperature changes will affect tire pressure, The matching full size spare wheel and tire assembly (if and the TPMS will monitor the actual tire pressure in equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The the tire. TPMS will only monitor the pressure in the full size spare Base System — If Equipped when it is used in place of a road tire.
368 STARTING AND OPERATING The TPMS consists of the following components: Tire Pressure Monitoring Low Pressure Warnings • Receiver module, • Four TPM sensors, • Various TPMS messages, which display in the Electronic Vehicle Information Center (EVIC), and • TPM Telltale Light The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor. The full size spare can be used in place of any of the four road tires.
STARTING AND OPERATING 369 value as shown in the ⬙Inflate to XX⬙ message. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing or return to it’s original color, and the “Tire Pressure Monitoring Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information.
370 STARTING AND OPERATING Light” will no longer flash, and the ⬙SERVICE TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. Tire Pressure Monitor Display 3.
STARTING AND OPERATING 371 Vehicles With Full Size Spare Tire Pressure Information System (TPIS) Chassis Cab — If Equipped 1. The matching full size spare wheel and tire assembly has a TPM sensor that can be monitored by the TPMS. Your vehicle may be equipped with a Tire Pressure Information System (TPIS). 2.
372 STARTING AND OPERATING • Six TPM sensors (Dual Rear Wheel [DRW] applica- If the ignition switch is cycled, this sequence will repeat, tions) providing the system fault still exists. If the system fault no longer exists, the ⬙SERVICE TPM SYSTEM⬙ message • Pressure display in the Electronic Vehicle Information will no longer be displayed, and a pressure value will Center (EVIC) display in place of the dashes.
STARTING AND OPERATING 373 General Information FUEL REQUIREMENTS This device complies with Part 15 of the FCC rules and 5.7L Engines RSS 210 of Industry Canada. Operation is subject to the This engine is designed to meet all emissions following conditions: regulations and provide satisfactory fuel • This device may not cause harmful interference. economy and performance when using high quality unleaded gasoline having an octane • This device must accept any interference received, range of 87 to 89.
374 STARTING AND OPERATING Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications, if they are available.
STARTING AND OPERATING 375 CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol. Use of these blends may result in starting and drivability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the “Malfunction Indicator Light” to illuminate. Pump labels should clearly communicate if a fuel contains greater than 10% Ethanol.
376 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some E-85 perform the following: vehicles. The manufacturer recommends that gasoline • Drain the fuel tank (see your authorized dealer). without MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, • Change the engine oil and oil filter.
STARTING AND OPERATING 377 Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
378 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 379 CAUTION! (Continued) • A poorly fitting gas cap may cause the MIL to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: Tighten the gas cap ¼ turn until you hear one click. This is an indication that the cap is properly tightened. If the gas cap is not tightened properly, the Malfunction Indicator Light will come on.
380 STARTING AND OPERATING Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the EVIC telltale display area. Refer to “Electronic Vehicle Information Center (EVIC) in “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the SELECT button to turn off the message.
STARTING AND OPERATING 381 Gross Axle Weight Rating (GAWR) Inflation Pressure The GAWR is the maximum permissible load on the front This is the cold tire inflation pressure for your vehicle for and rear axles. The load must be distributed in the cargo all loading conditions up to full GAWR. area so that the GAWR of each axle is not exceeded.
382 STARTING AND OPERATING The weight on the front and rear of the vehicle should CAUTION! then be determined separately to be sure that the load is properly distributed over the front and rear axle. Weigh- Do not load your vehicle any heavier than the GVWR ing the vehicle may show that the GAWR of either the or the maximum front and rear GAWR. If you do, front or rear axles has been exceeded but the total load is parts on your vehicle can break, or it can change the within the specified GVWR.
STARTING AND OPERATING 383 To maintain the New Vehicle Limited Warranty coverage, Gross Trailer Weight (GTW) follow the requirements and recommendations in this The GTW is the weight of the trailer plus the weight of all manual concerning vehicles used for trailer towing. cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and Common Towing Definitions ready for operation⬙ condition.
384 STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING 385 Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control, thereby enhancing towing safety.
386 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
STARTING AND OPERATING 387 Trailer Towing Weights (Maximum Trailer Weight Ratings) CHASSIS CAB 3500 5.7L HEMI® 6-Speed Automatic Transmission 6.4L HEMI® 6-Speed Automatic Transmission ST/SLT/Laramie Towing: 14,050 lbs (6 372 kg) Payload: 4,728 lbs (2 144 kg) Towing: 17,850 lbs (8 096 kg) Payload: 8,013 lbs (3 634 kg) 5 CHASSIS CAB 4500 6.
388 STARTING AND OPERATING CHASSIS CAB 5500 6.4L HEMI® 6-Speed Automatic Transmission ST/SLT/Laramie Towing: 18,900 lbs (8 572 kg) Payload: 11,080 lbs (5 025 kg) NOTE: For additional trailer towing information (maxi- cause of many trailer collisions. Never exceed the maximum trailer weight ratings) refer to the following website mum tongue weight stamped on your trailer hitch. addresses: • http://www.ramtrucks.com. • http://www.ramtruck.ca (Canada).
STARTING AND OPERATING 389 Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your new vehicle drive• The tongue weight of the trailer train components the following guidelines are recom• The weight of any other type of cargo or equipment mended: put in or on your vehicle • The weight of the driver and all passengers NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
390 STARTING AND OPERATING WARNING! WARNING! (Continued) Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision.
STARTING AND OPERATING 391 WARNING! (Continued) • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized. Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
392 STARTING AND OPERATING Towing Requirements — Trailer Brakes WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
STARTING AND OPERATING 393 • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 1,653 lbs (750 kg). Integrated Trailer Brake Module — If Equipped Your vehicle may have an Integrated Trailer Brake Module (ITBM) for Electric and Electric Over Hydraulic (EOH) trailer brakes. NOTE: This module has been designed and verified with electric trailer brakes and new electric over hydraulic systems. Some previous EOH systems may not be compatible with ITBM.
394 STARTING AND OPERATING The user interface consists of the following: Manual Brake Control Lever Slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes.
STARTING AND OPERATING 395 Adjusting GAIN 4. Press the UP or DOWN button on the steering wheel until “TRAILER TOW” appears on the screen. NOTE: This should only be performed in a traffic free environment at speeds of approximately 20–25 mph 5. Press the RIGHT arrow on the steering wheel to enter (30–40 km/h). “TRAILER TOW”. 1. Make sure the trailer brakes are in good working 6. Press the UP or DOWN buttons until Trailer Brake condition, functioning normally and properly adType appears on the screen.
396 STARTING AND OPERATING Repeat steps 8 and 9 until the GAIN setting is at a point trailer, trailer wheel lockup may not be attainable even just below trailer wheel lockup. If towing a heavier with the maximum GAIN setting of 10.
STARTING AND OPERATING 397 CAUTION! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in damage to your vehicle, trailer, or other property. WARNING! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking.
398 STARTING AND OPERATING WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automotive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury.
STARTING AND OPERATING 399 Tow/Haul Mode Cooling System To reduce potential for automatic transmission overheating, turn the “TOW/HAUL” feature ON when driving in hilly areas, or select a lower gear range (using the Electronic Range Select (ERS) switches) on more severe grades. To reduce potential for engine and transmission overheating, take the following actions: Electronic Speed Control — If Equipped • Do not use in hilly terrain or with heavy loads.
400 STARTING AND OPERATING NOTE: Before installation of a snowplow it is highly recCAUTION! ommended that the owner/installer obtain and follow the recommendations contained within the current Ram Body The “Lamp Out” indicator could illuminate if exteBuilders Guide. See your authorized dealer, installer or rior lamps are not properly installed. snowplow manufacturer for this information.
STARTING AND OPERATING 401 Snowplow Prep Package Model Availability NOTE: Detach the snowplow when transporting passengers. For Information about snowplow applications visit www.ramtrucks.com or refer to the current Ram Body Vehicle front end wheel alignment was set to specifications at the factory without consideration for the weight Builders Guide. of the plow. Front end toe-in should be checked and reset 1.
402 STARTING AND OPERATING Over The Road Operation With Snowplow Attached The blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Therefore, when transporting the plow, angle the blade completely and position it as low as road or surface conditions permit. Do not exceed 40 mph (64 km/h). The operator should always maintain a safe stopping distance and allow adequate passing clearance.
STARTING AND OPERATING 403 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
404 STARTING AND OPERATING 5. Turn the ignition switch to the OFF position and remove the Key Fob. DO NOT flat tow this vehicle. Damage to the drivetrain will result. 6. Install a suitable clamping device, designed for towing, to secure the front wheels in the straight position. Recreational towing (for two-wheel drive models) is Recreational Towing — Two-Wheel Drive Models allowed ONLY if the rear wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer.
STARTING AND OPERATING 405 Recreational Towing — Four-Wheel Drive Models CAUTION! (Continued) NOTE: Both the manual shift and electronic shift transfer cases must be shifted into NEUTRAL (N) for recreational towing. Automatic transmissions must be shifted into PARK for recreational towing. Manual transmissions must be placed in gear (NOT in NEUTRAL) for recreational towing. Refer to the following for the proper transfer case NEUTRAL (N) shifting procedure for your vehicle.
406 STARTING AND OPERATING CAUTION! (Continued) WARNING! (Continued) • Do not disconnect the rear drive shaft because fluid will leak from the transfer case, causing damage to internal parts. • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. the parking brake. The transfer case NEUTRAL (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, even if the transmission is in PARK.
STARTING AND OPERATING 407 4. Depress the clutch pedal on a manual transmission. 6. Release the parking brake. 5. If the transfer case is in 4WD AUTO (if equipped), press a selector button or rotate the selector switch to shift the transfer case into the 2WD or 4WD LOCK position. • With manual shift transfer case, shift the transfer case lever into NEUTRAL (N). • With electronic shift transfer case, press and hold the transfer case NEUTRAL (N) button.
408 STARTING AND OPERATING 13. Attach the vehicle to the tow vehicle using a suitable tow bar. 14. Release the parking brake. NOTE: With electronic shift transfer case: • The ignition switch must be in the ON/RUN position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the ON/RUN position, the shift will not take place and no position indicator lights will be on or flashing.
STARTING AND OPERATING 409 3. Firmly apply the parking brake. 4. Press and hold the brake pedal. 5. Shift the transmission into NEUTRAL. • With manual shift transfer case, shift the transfer case lever to the desired position. • With electronic shift transfer case, press and hold the transfer case NEUTRAL (N) button until the NEUTRAL (N) indicator light turns off. After the NEUTRAL (N) indicator light turns off, release the NEUTRAL (N) button.
410 STARTING AND OPERATING • The ignition switch must be in the ON/RUN position for a shift to take place and for the position indicator • Steps 3 through 5 are requirements that must be met lights to be operable. If the ignition switch is not in the prior to pressing the button to shift out of NEUTRAL ON/RUN position, the shift will not take place and no (N), and must continue to be met until the shift has position indicator lights will be on or flashing. been completed.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .412 䡵 JUMP-STARTING PROCEDURES . . . . . . . . . . .423 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .412 ▫ Torque Specifications . . . . . . . . . . . . . . . . . .412 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .415 ▫ 4500/5500 Models . . . . . . . . . . . . . . . . . . . . .415 ▫ Preparations For Jacking. . . . . . . . . . . . . . . . .416 ▫ Jacking Instructions . . . . . . . . . . . .
412 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS WHEEL AND TIRE TORQUE SPECIFICATIONS The Hazard Warning flasher switch is located on the Proper lug nut/bolt torque is very important to ensure upper switch bank just below the radio. that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the Press the switch to turn on the Hazard Warning vehicle the lug nuts/bolts should be torqued using a flasher.
WHAT TO DO IN EMERGENCIES 413 Inspect the wheel mounting surface prior to mounting Do not oil wheel studs. For chrome wheels, do not the tire and remove any corrosion or loose particles. substitute with chrome plated wheel nuts. NOTE: Dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer.
414 WHAT TO DO IN EMERGENCIES After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. 10 Lug Nuts/Bolts Torque Pattern WARNING! 8 Lug Nuts/Bolts Torque Pattern To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury.
WHAT TO DO IN EMERGENCIES 415 JACKING AND TIRE CHANGING WARNING! (Continued) WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
416 WHAT TO DO IN EMERGENCIES 4. Place the shift lever into PARK (automatic transmission) or REVERSE (manual transmission). On 4-Wheel 1. Park the vehicle on a firm, level surface. Avoid ice or drive vehicles, shift the transfer case to the “4L” slippery areas. position. Preparations For Jacking WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 5.
WHAT TO DO IN EMERGENCIES 417 Jacking Instructions WARNING! (Continued) Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised.
418 WHAT TO DO IN EMERGENCIES Jack Warning Label 3. When changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1.
WHAT TO DO IN EMERGENCIES 419 When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. Connect the jack tube extension and lug wrench. Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required.
420 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. Install WARNING! the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel on single rear wheel A loose tire or jack thrown forward in a collision or (SRW) models. On dual rear wheel models (DRW) the hard stop could injure someone in the vehicle. Allug nuts are a two-piece assembly with a flat face. ways stow the jack parts and the extra tire and wheel Lightly tighten the nuts.
WHAT TO DO IN EMERGENCIES 421 On 3500 models with dual rear wheels (DRW), you must The hub caps must be removed before raising the vehicle first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pull off notch of the off the ground. rear hub caps. Position the hook and pull straight out on the ratchet firmly. The hub cap should pop off. The wheel CAUTION! skins can now be removed.
422 WHAT TO DO IN EMERGENCIES You must use the flat end of the lug wrench to pull off the wheel skins. Locate the hub cap pull notches (2 notches on each cap). Insert the flat tip completely and using a back and forth motion, loosen the wheel skin. Repeat this procedure around the tire until the skin pops off. Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lug nut bolt circle and strike the high side down with a rubber mallet.
WHAT TO DO IN EMERGENCIES 423 To Stow The Flat Or Spare — If Equipped JUMP-STARTING PROCEDURES Refer to Upfitters Body Builders Guide for information If your vehicle has a discharged battery it can be jumpon stowing your spare tire (if equipped). started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster HOISTING pack.
424 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post.
WHAT TO DO IN EMERGENCIES 425 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
426 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. Connecting The Jumper Cables 1.
WHAT TO DO IN EMERGENCIES 427 6. Once the engine is started, remove the jumper cables in the reverse sequence: Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
428 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle.
WHAT TO DO IN EMERGENCIES 429 WARNING! WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. • Do not use a chain for freeing a stuck vehicle.
430 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: 1. Turn the engine OFF. 2. Firmly apply the parking brake. 3. Tilt the steering wheel to the full up position. 4. Press and maintain firm pressure on the brake pedal. 5.
WHAT TO DO IN EMERGENCIES 431 be towed as described under “Recreational Towing” in the This section describes procedures for towing a disabled “Starting and Operating” section. vehicle using a commercial wrecker service.
432 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent CAUTION! damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- Do not use sling type equipment when towing. ment manufacturer’s instructions. Use of safety chains is When securing the vehicle to a flat bed truck, do not mandatory. Attach a tow bar or other towing device to attach to front or rear suspension components.
WHAT TO DO IN EMERGENCIES 433 If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km), tow with the rear wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed, or with the front wheels raised and the rear wheels on a towing dolly, or (when using a suitable steering wheel stabilizer to hold the front wheels in the straight position) with the rear wheels raised and the front wheels on the ground.
434 WHAT TO DO IN EMERGENCIES CAUTION! • Front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 5.7L . . . . . . . . . .437 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .446 䡵 ENGINE COMPARTMENT — 6.4L . . . . . . . . . .438 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .447 䡵 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . .439 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .447 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .439 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .
436 MAINTAINING YOUR VEHICLE ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . .454 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . . .486 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .462 ▫ Rear Axle And 4x4 Front Driving Axle Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . .464 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . .465 ▫ Automatic Transmission — Aisin F21-250 HD Transmission — If Equipped . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 437 ENGINE COMPARTMENT — 5.
438 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 6.
MAINTAINING YOUR VEHICLE 439 ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
440 MAINTAINING YOUR VEHICLE Refer to “Electronic Vehicle Information Center (EVIC) in “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 441 3. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
442 MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment.
MAINTAINING YOUR VEHICLE 443 CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized dealer or qualified repair center. • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals.
444 MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could damage your engine. Engine Oil Selection — 5.7L Engine For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. Change Engine Oil Engine Oil Selection — 6.
MAINTAINING YOUR VEHICLE 445 American Petroleum Institute (API) Engine Oil Identification Symbol Engine Oil Viscosity — 5.7L Engine MOPAR SAE 5W-20 engine oil or equivalent Pennzoil® or Shell Helix® is recommended for all operating temThis symbol means that the oil has peratures. This engine oil improves low temperature been certified by the American starting and vehicle fuel economy. Petroleum Institute (API).
446 MAINTAINING YOUR VEHICLE environment. Contact your authorized dealer, service station or governmental agency for advice on how and Use Pennzoil Ultra™ 0W–40 engine or equivalent where used oil and oil filters can be safely discarded in MOPAR® oil meeting the Chrysler Material Standard your area. MS-12633 for use in all operating temperatures. Engine Oil Filter The engine oil filler cap also shows the recommended engine oil viscosity for your engine.
MAINTAINING YOUR VEHICLE 447 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” for the proper The quality of replacement engine air cleaner filters maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recomWARNING! mended. The air induction system (air cleaner, hoses, etc.
448 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. • Battery gas is flammable and explosive.
MAINTAINING YOUR VEHICLE 449 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
450 MAINTAINING YOUR VEHICLE Front Prop Shaft Lubrication — Four-Wheel Drive Models components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. Lubricate the front driveshaft grease fitting at each oil change. Refer to the “Maintenance Schedule” for the The external lock cylinders should be lubricated twice a proper maintenance intervals. Use MOPAR® Type year, preferably in the Fall and Spring.
MAINTAINING YOUR VEHICLE 451 Avoid using the wiper blades to remove frost or ice from To prevent freeze-up of your windshield washer system the windshield. Keep the blade rubber out of contact with in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This petroleum products such as engine oil, gasoline, etc. rating information can be found on most washer fluid NOTE: Life expectancy of wiper blades varies dependcontainers.
452 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE 453 CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
454 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. WARNING! (Continued) you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
MAINTAINING YOUR VEHICLE 455 Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks. Cooling System — Drain Flush And Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
456 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
MAINTAINING YOUR VEHICLE 457 • Mix a minimum solution of 50% OAT engine coolant that meets the requirements of Chrysler Material StanYour vehicle has been built with an improved engine dard MS-12106 and distilled water. Use higher concencoolant (OAT coolant conforming to MS-12106) that trations (not to exceed 70%) if temperatures below allows extended maintenance intervals. This engine cool−34° F (−37° C) are anticipated.
458 MAINTAINING YOUR VEHICLE NOTE: • Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. • Mixing engine coolant (antifreeze) types is not recommended and can result in cooling system damage.
MAINTAINING YOUR VEHICLE 459 Disposal Of Used Engine Coolant To check the coolant level: Used ethylene glycol-based engine coolant (antifreeze) is 1. Open the coolant reservoir. a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
460 MAINTAINING YOUR VEHICLE When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Checking Coolant Level — 6.4L Engine The level of the coolant in the pressurized coolant bottle should be between the “MIN” and “MAX” range on the bottle when the engine is cold.
MAINTAINING YOUR VEHICLE 461 • If frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming from the front of the engine compartment.
462 MAINTAINING YOUR VEHICLE Brake System Brake Fluid Level Check In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The fluid level of the master cylinder should be checked when performing under the hood service or immediately if the brake system warning lamp indicates system failure. WARNING! Riding the brakes can lead to brake failure and possibly a collision.
MAINTAINING YOUR VEHICLE 463 WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir.
464 MAINTAINING YOUR VEHICLE Rear Axle And 4x4 Front Driving Axle Fluid Level For models with 9.25 in Front Axles and 11.5 in Rear Axles, refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons, the exterior surfaces of the axle assembly should be inspected. When checking the fluid level (4500/5500 only), the vehicle should be in a level position.
MAINTAINING YOUR VEHICLE 465 Lubricant Selection Transfer Case Refer to “Fluids, Lubricants, and Genuine Parts” in Drain And Refill “Maintaining Your Vehicle” for further information. Refer to the “Maintenance Schedule” for the proper NOTE: The presence of water in the gear lubricant will maintenance intervals. result in corrosion and possible failure of differential Lubricant Selection components.
466 MAINTAINING YOUR VEHICLE Automatic Transmission — Aisin F21-250 HD Transmission — If Equipped Selection Of Lubricant It is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. It is important to maintain the transmission fluid at the correct level using the recommended fluid.
MAINTAINING YOUR VEHICLE 467 CAUTION! Fluid Level Check — Procedure It is best to check the fluid level when the transmission is at normal operating temperature (170-180°F / 77-82°C for 66RFE transmission, or 158–176°F / 70–80°C for AS66RC transmission). This normally occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips.
468 MAINTAINING YOUR VEHICLE 3. Run the engine at normal idle speed for at least 60 8. Remove the dipstick again and note the fluid level on seconds, and leave the engine running for the rest of both sides. The fluid level reading is only valid if there this procedure. is a solid coating of oil on both sides of the dipstick. Note that the holes in the dipstick will be full of fluid 4. Fully apply the parking brake and press the brake. if the actual level is at or above the hole. The fluid level 5.
MAINTAINING YOUR VEHICLE 469 NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at 60-70°F / 16-21°C for 66RFE transmission, or 68-86°F / 20-30°C for AS66RC transmission. Only use the COLD region of the dipstick as a rough reference when setting the fluid level after a transmission service or fluid change.
470 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion What Causes Corrosion? Protection Of Body And Paint From Corrosion Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE 471 • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once a month. • Use a high quality cleaner wax, such as MOPAR® Cleaner Wax to remove road film, stains and to protect • It is important that the drain holes in the lower edges your paint finish.
472 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, NOTE: If your vehicle is equipped with Dark Vapor de-icer salt, etc., be sure that such materials are well Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permanently damage packaged and sealed. this finish and such damage is not covered by the New • If a lot of driving is done on gravel roads, consider Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 473 Stain Repel Fabric Cleaning Procedure — If Equipped Interior Care Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. • Remove as much of the stain as possible by blotting MOPAR® Total Clean is specifically recommended for with a clean, dry towel. leather upholstery. • Blot any remaining stain with a clean, damp towel.
474 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. CAUTION! To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
MAINTAINING YOUR VEHICLE 475 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth.
476 MAINTAINING YOUR VEHICLE WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Power Distribution Center The Power Distribution Center is located in the engine compartment near the battery. This center contains cartridge fuses, micro fuses, relays, and circuit breakers.
MAINTAINING YOUR VEHICLE 477 Cavity F01 F03 F05 F06 F07 F08 F10 F10 Cartridge Fuse 80 Amp Red 60 Amp Yellow 40 Amp Green 40 Amp Green 40 Amp Green 20 Amp Yellow (Cummins Diesel) 20 Amp Yellow (1500 LD Diesel) 40 Amp Green (Cummins Diesel) 30 Amp Pink (1500 LD Diesel) 40 Amp Green 50 Amp Red F11 30 Amp Pink F09 Micro Fuse Description Rad Fan Control Module – If equipped Rad Fan – If Equipped Compressor for Air Suspension – If Equipped Antilock Brakes/Electronic Stability Control Pump Starter Solenoid
478 MAINTAINING YOUR VEHICLE Cavity F12 F13 F14 F15 F19 F20 F21 F22 F23 F24 F25 F25 F26 F28 F29 Cartridge Fuse 40 Amp Green 40 Amp Green 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink 20 Amp Yellow 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink 20 Amp Yellow 20 Amp Yellow Micro Fuse Description Body Controller #3 / Interior Lights Blower Motor Body Controller #4 / Power Locks Electric Park Brake Right Side – If Equipped SCR – If Equipped Passenger Door Module Drive Train Contr
MAINTAINING YOUR VEHICLE 479 Cavity F30 F32 F33 F34 F35 F36 F37 F38 F39 F41 F42 F43 F44 F46 Cartridge Fuse 30 Amp Pink 30 Amp Pink 20 Amp Yellow 30 Amp 30 Amp 30 Amp 30 Amp 30 Amp 30 Amp Micro Fuse Pink Pink Pink Pink Pink Pink 10 Amp Red 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red Description Trailer Tow Receptacle Drive Train Control Module – If Equipped Cummins Diesel Fuel Heater #1 – If Equipped / Rear Blower – If Equipped Vehicle System Interface Module #2 – If Equipped Sunroof – If Equipped Re
480 MAINTAINING YOUR VEHICLE Cavity F47 F49 F50 F51 F52 F53 F54 F55 F56 F57 F58 F60 Cartridge Fuse Micro Fuse 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red 5 Amp Tan 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 20 Amp Yellow (Gas Engine) / 25 Amp Natural (Cummins Diesel Engine) 15 Amp Blue Description Snow Plow (Right) – If Equipped Instrument Panel Cluster Air Suspension Control Module – If Equipped Ignition Node Module / Keyless Ignition Battery Sensor Trailer Tow – Left Turn/
MAINTAINING YOUR VEHICLE 481 Cavity F61 F62 F63 F64 F65 F66 F67 F69 F70 F71 F72 Cartridge Fuse Micro Fuse 20 Amp Yellow 10 Amp Red 20 Amp Yellow 25 Amp Natural 10 Amp Red 10 Amp Red 10 Amp Red 15 Amp Blue 30 Amp Green 25 Amp Natural 10 Amp Red Description Power Take-off Unit – If Equipped Air Conditioning Clutch Ignition Coils (Gas), Urea Heater (Cummins Diesel) Fuel Injectors / Powertrain USB interface Sunroof / Passenger Window Switches / Rain Sensor CD / DVD / Bluetooth Hands-free Module – If Equippe
482 MAINTAINING YOUR VEHICLE Cavity F74 Cartridge Fuse F75 F76 F77 Micro Fuse 20 Amp Yellow (Gas Engine & 1500 LD Diesel) / 10 Amp Red (Cummins Diesel Engine) 10 Amp Red 10 Amp Red 10 Amp Red F78 F79 F80 F81 F82 F84 10 Amp Red 15 Amp Blue 10 Amp Red 20 Amp Yellow 10 Amp Red 15 Amp Blue Description Brake Vacuum Pump Gas/Diesel – If Equipped Coolant Temperature Valve Actuator Antilock Brakes/Electronic Stability Control Drivetrain Control Module/Front Axle Disconnect Module Engine Control Module / Ele
MAINTAINING YOUR VEHICLE 483 Cavity F85 F86 F87 Cartridge Fuse Micro Fuse 10 Amp Red 10 Amp Red 10 Amp Red F88 F90/ F91 F93 F94 F95 F96 F97 15 Amp Blue 20 Amp Yellow 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red 25 Amp Natural F98 F99 25 Amp Natural 10 Amp Red Description Airbag Module Airbag Module Air Suspension-If Equipped / Trailer Tow / Steering Column Control Module Instrument Panel Cluster Power Outlet (Rear seats) Customer Selectable Cigar Lighter Shifter / Transfer Case Module Rear Camera
484 MAINTAINING YOUR VEHICLE Cavity F101 Cartridge Fuse F104 Micro Fuse 15 Amp Blue 20 Amp Yellow Description Electrochromatic Mirror / Smart High Beams – If Equipped Power Outlets (Instrument Panel/Center Console) CAUTION! CAUTION! (Continued) • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE 485 VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the negative cable from battery. LIGHT BULBS — Interior Bulb Number TS 212-2 Overhead Console Lamps Dome Lamp 7679 For lighted switches, see your authorized dealer for replacement instructions. • Any time you store your vehicle or keep it out of service (i.e.
486 MAINTAINING YOUR VEHICLE Premium Headlamp – Low Beam Premium Headlamp – High Beam Premium Headlamp – Front Turn Signal Lamp Horizontal Fog Lamp Vertical Fog Lamp Cab Roof Marker Lamps Center High Mounted Stop Lamp Rear Cargo Lamp Bulb Number HIR2 9005 LED (See authorized dealer for service) 9145 9006 194NA 921 921 Box Off Tail Lamps – Stop/Turn/Tail/License Plate Box Off Tail Lamps – Back Up Bulb Number 1157 1156 BULB REPLACEMENT NOTE: Lens fogging can occur under certain atmospheric conditions.
MAINTAINING YOUR VEHICLE 487 Base Quad / Premium Bi-Halogen: Low Beam Headlamp, High Beam Headlamp, Front Park And Turn — If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges. 4. Remove the two plastic push-in rivets that secure the upper radiator seal to the radiator. 5. Remove the upper radiator seal from the vehicle.
488 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 9. Remove the headlamp assembly. Grasp the outboard splash shield and lift the slide lock upward far enough edge of the lamp and pull it straight forward to to disengage it from the lock post on the back of the disengage the ball stud from the plastic grommet. front lamp unit housing. 10. Disconnect the wiring harness connectors from the bulb socket. 11. Replace bulb(s) as necessary.
MAINTAINING YOUR VEHICLE 489 NOTE: There are access covers over both headlamp bulb Center High-Mounted Stoplamp (CHMSL) With access holes in the quad front lamp unit housing (if Cargo Lamp equipped). These covers MUST be reinstalled after the bulb 1. Remove the two screws holding the housing/lens to has been replaced. the body as shown. Fog Lamps — If Equipped 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2.
490 MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wiring harness to the body. CHMSL Bulb And Socket CHMSL Connector Location 3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE 491 • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing. Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp. Removing Rear Screw From Clearance Lamp 2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly.
492 MAINTAINING YOUR VEHICLE Removing Bulb Socket From Clearance Lamp 3. Pull the bulb straight from it’s socket and replace.
MAINTAINING YOUR VEHICLE 493 FLUID CAPACITIES Fuel (Approximate) Standard Rear Tank Optional Midship Tank Engine Oil With Filter 5.7L Engine (SAE 5W-20, API Certified) 6.4L Engine (SAE 0W-40, Synthetic API Certified) Cooling System 5.7L Engine (MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula). 6.4L Engine (MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula). U.S. Metric 52 Gallons 22 Gallons 197 Liters 83 Liters 7 Quarts 7 Quarts 6.6 Liters 6.6 Liters 18.7 Quarts 17.7 Liters 18.
494 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 5.7L Engine Engine Oil – 5.7L Engine For trucks operating under a gross combined weight rating greater than 14,000 lbs/(6,350 kg.) Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10–Year/ 150,000 Mile Formula OAT (Organic Additive Technology).
MAINTAINING YOUR VEHICLE 495 Component Engine Oil – 6.4L Engine Engine Oil Filter – 5.7L Engine Engine Oil Filter – 6.4L Engine Spark Plugs – 5.7L Engine Spark Plugs – 6.4L Engine Fuel Selection – 5.7L Engine Fuel Selection – 6.4L Engine Fluid, Lubricant, or Genuine Part For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SN.
496 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission (5.7L, and 6.4L Engine with 66RFE Transmission) (For Diesel Engine see Diesel Supplement) Automatic Transmission (6.4L Engine with AS66RC Transmission) Transfer Case Front and Rear Axle Fluid (4500/5500) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® ATF+4® Automatic Transmission Fluid or equivalent licensed ATF+4® product.
M A I N T E N A ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . .500 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 498 MAINTENANCE SCHEDULES than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)/Oil Change Required” in indicator system. The oil change indicator system will “Understanding Your Instrument Panel” for further inremind you that it is time to take your vehicle in for formation scheduled maintenance.
MAINTENANCE SCHEDULES 499 M Once A Month Or Before A Long Trip: • Check engine oil level • Check windshield washer fluid level • Check the tire inflation pressures and look for unusual wear or damage • Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic transmission as needed • Check function of all interior and exterior lights Required Maintenance Refer to the Maintenance Schedules on the following pages for required maintenance.
8 Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle surfaces. If gear oil leakage is suspected, check the fluid level. If using your vehicle for police, taxi, fleet, off-road or frequent trailer towing, change axle fluid.
Inspect the brake linings, parking brake function. Inspect transfer case fluid. Additional Maintenance Replace engine air filter. Replace spark plugs (5.7L engine).** Replace spark plugs (6.4L engine).
S C H E D U L E S 8 Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change the automatic transmission fluid (AS66RC Transmission Only). Change the automatic transmission fluid and sump filter (AS66RC Transmission Only).
Change the automatic transmission fluid and filter(s) (66RFE Transmission Only), if using your vehicle for police, taxi, fleet, or frequent trailer towing. Change the automatic transmission fluid and filter(s). Inspect the transfer case fluid, change for any of the following: police, taxi, fleet, or frequent trailer towing.
20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 2 3 4 5 6 7 8 9 10 11 12 13 14 15 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 M 504 MAINTENANCE SCHEDULES A I Mileage or time passed N (whichever comes first) T E N Or Years: A Or Kilometers: N C E S Change the transfer case fluid. C Inspect and replace PCV valve if H necessary.
MAINTENANCE SCHEDULES 505 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .509 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .511 ▫ Prepare For The Appointment. . . . . . . . . . . . .509 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .511 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .509 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
508 IF YOU NEED CONSUMER ASSISTANCE 䡵 PUBLICATION ORDER FORMS . . . . . . . . . . . .514 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .515 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . .515 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .516 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 509 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
510 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 511 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
512 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 513 To contact NHTSA, you may either call the Auto Safety MOPAR® fluids, lubricants, parts, and accessories are Hotline toll free at 1–888–327–4236 (TTY: 1–800–424–9153), available from an authorized dealer. They are recom- or go to http://www.safercar.gov; or write to: Administramended for your vehicle in order to help keep the vehicle tor, NHTSA, 1200 New Jersey Avenue, SE., West Building, Washington, D.C. 20590. You can also obtain other inforoperating at its best.
514 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 515 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
516 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
518 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .457 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .378 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .376 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .161 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .70 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 519 Special Additives . . . . . . . . . . . . . . . . . . . . . . .466 Axle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .464 Axle Lubrication (Axle Fluid) . . . . . . . . . . . . . . . . .464 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .447 Keyless Transmitter Replacement (RKE) . . . . . . . .29 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Body Builders Guide . . . . . . . . . . . . . . . . . . . . . . . .
520 INDEX Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Cigar Lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . .374 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .472 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . .261 Cold Weather Operation . . . . . . . . . . . . . . . . . . .
INDEX 521 Emergency, In Case of Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . .459 Freeing Vehicle When Stuck . . . . . . Hazard Warning Flasher . . . . . . . . Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Jump Starting . . . . . . . . . . . . . . . . Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . . .38 Tow Hooks . . . . . . . . . . . . . . . . . . Driving Through Flowing, Rising, or Shallow Standing Emission Control System Maintenance Water .
522 INDEX Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . .446 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . .446 Enhanced Accident Response Feature . . . . . . . . . . . .70 Entry System, Illuminated . . . . . . . . . . . . . . . . . . . .22 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .374 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . . .73 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . . . . . .109 Exhaust System. . .
INDEX 523 Ethanol . . . . . . . . . . . . Filler Cap (Gas Cap) . . . Filter . . . . . . . . . . . . . . Gasoline . . . . . . . . . . . . Materials Added . . . . . . Methanol . . . . . . . . . . . Octane Rating . . . . . . . . Requirements . . . . . . . . Tank Capacity . . . . . . . . Fuses . . . . . . . . . . . . . . . . Gas Cap (Fuel Filler Cap) . Gasoline, Clean Air . . . . . . Gasoline (Fuel) . . . . . . . . . Gasoline, Reformulated . . . Gauges Speedometer . . . . . . . . Tachometer . . . . . . . . . .
524 INDEX Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 High Beam/Low Beam Select (Dimmer) Switch . . . .156 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . .386 Hoisting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 Hub Caps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 525 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . . .373 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .357 Light Bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Airbag . . . . . . . . . . . . . . . . . . . . . . . . .
526 INDEX Tire Pressure Monitoring (TPMS) . . . . . . . . . . . .198 Traction Control . . . . . . . . . . . . . . . . . . . . . . . .336 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . .309 Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Warning (Instrument Cluster Description) . . . . . .192 Limited-Slip Differential . . . . . . . . . . . . . . . . . . . .316 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .380 Tires . . . . . . . . . . . . . . . .
INDEX 527 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . .48 Occupant Restraints (Sedan) . . . . . . . . . . . . . . . . . .67 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . . .373 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .493 Change Interval . . . . . . . . . . . . . . . . . . . . . . . .444 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443 Disposal . . .
528 INDEX Sliding Rear Window . . . . . . . . . . . . . . . . . . . .185 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .320 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . . .496 Pregnant Women and Seat Belts . . . . . . . . . . . . . . . .63 Programmable Electronic Features . . . . . . . . . . . . .231 Programming Transmitters (Remote Keyless Entry) . .23 Radial Ply Tires . . . . . . . . . . . . . . .
INDEX 529 Safety Information, Tire . . . . . . . . . . . . . . . . . . . . .338 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . .498 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . .475 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . . .62 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Adjustable Upper Shoulder Anchorage . . . . . . . . .
530 INDEX Sliding Rear Window Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . . .360 Snow Plow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .399 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .352 Spare Tire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .354 Spark Plugs . . . . . . . . . . . . . . . . . . .
INDEX 531 Compact Spare . . . . . . . . . . . . . Dual . . . . . . . . . . . . . . . . . . . . General Information . . . . . . . . . High Speed . . . . . . . . . . . . . . . Inflation Pressures . . . . . . . . . . . Life of Tires . . . . . . . . . . . . . . . Load Capacity . . . . . . . . . . . . . Pressure Monitor System (TPMS) Pressure Warning Light . . . . . . . Quality Grading . . . . . . . . . . . . Radial . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . . Rotation . . . .
532 INDEX Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .397 Trailer Towing Guide. . . . . . . . . . . . . . . . . . . . . . .387 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .387 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 Electronically Shifted . . . . . . . . . . . . . . . . . . . . .309 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .496 Transmission Automatic . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 533 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Rear Sliding . . . . . . . . . . . . . . . . . . . . . . . . . . .185 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . . .111 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . .156 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . . .450 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2014 ProMaster 2014 OWNER’S MANUAL Chrysler Group LLC 14DD43-126-AC 14VF-126-AA 3ED-R1 Edition First Edition Printed in U.S.A.
