2014 ProMaster 2014 OWNER’S MANUAL Chrysler Group LLC 14VF-126-AD Fourth Edition Rev 2 Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .8 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .6 䡵 VAN CONVERSIONS/CAMPERS . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury.
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER 1 The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle frame and underbody as well as the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM . . . . . . . . . . . . . .17 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .17 ▫ Locking Doors With A Key . . . . . . . . . . . . . . .14 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 ▫ To Disarm The System . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Transmitter Battery Replacement . . . . . . . . . . .20 ▫ Automatic Locking Retractor (ALR) Mode . . . . .35 ▫ General Information . . . . . . . . . . . . . . . . . . . .21 ▫ Energy Management Feature . . . . . . . . . . . . . .36 䡵 POWER DOOR LOCKS . . . . . . . . . . . . . . . . . . .21 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . .36 ▫ Automatic Door Locks — If Equipped . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 䡵 FUEL CUT OFF SWITCH . . . . . . . . . . . . . . . . . .61 䡵 ENGINE BREAK-IN RECOMMENDATIONS . . . .62 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .63 ▫ Transporting Passengers. . . . . . . . . . . . . . . . . .63 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The Key Fob contains the Remote Keyless Entry (RKE) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the authorized studio that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 3. Remove the key from the ignition switch lock cylinder. Ignition Switch Positions 1 — STOP (OFF/LOCK) 2 — MAR (ACC/ON/RUN) 3 — AVV (START) WARNING! • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK and remove the Key Fob from the ignition. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition and the ignition switch position is OFF/LOCK, sounds a signal to remove the key. STEERING WHEEL LOCK — IF EQUIPPED CAUTION! An unlocked car is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The system uses ignition keys which have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are proInsert the key in the ignition switch and start the engine. grammed to the vehicle can be used to start and operate If the key is difficult to turn, move the wheel slightly to the vehicle. the right or left to disengage the lock.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! (Continued) • The Sentry Key® Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. This PIN is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer. NOTE: When having the Sentry Key® Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: Changes or modifications not expressly approved alarm is still present, the system will ignore that condiby the party responsible for compliance could void the tion and monitor the remaining doors and ignition. user’s authority to operate the equipment. To Arm The System VEHICLE SECURITY ALARM To Arm The System The Vehicle Security Alarm will set when you use the Remote Keyless Entry (RKE) transmitter to lock the doors.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: The line of transmission must not be blocked with To Unlock The Doors metal objects. Press and release the UNLOCK button on RKE transmitter once to unlock only the front doors. Press and release the CARGO UNLOCK button on RKE transmitter once to unlock the cargo area (rear lateral sliding doors and rear door). The turn signal lights will flash to acknowledge the unlock signal.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Replacement NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate The recommended replacement battery is CR2032. 1. Press the mechanical key release button and release the mechanical key to access the battery case screw located on the side of the Key Fob. 2. Rotate the screw located on the side of the Key Fob using a small screwdriver. Key Fob Screw Location 3. Take out the battery case.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 General Information POWER DOOR LOCKS This device complies with Part 15 of the FCC rules and The central LOCK/UNLOCK button has an LED that RSS 210 of Industry Canada. Operation is subject to the indicates whether the doors are locked or unlocked. following conditions: • LED ON: doors locked. Press central LOCK/ • This device may not cause harmful interference. UNLOCK button once again to centrally unlock all doors. The LED will switch off.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The load compartment power door lock switch is located on the driver door trim panel. Use this switch to lock or unlock the load compartment doors. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • For personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows — If Equipped The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control. Power Window Switches NOTE: The Key Off Power Delay feature will allow the power windows to operate for up to three minutes after the ignition is turned OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle or in a location accessible to children.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Passenger seat belt systems include Automatic Locking Retractors (ALRs), which lock the seat belt webSome of the most important safety features in your bing into position by extending the belt all the way out vehicle are the restraint systems: and then adjusting the belt to the desired length to • Three-point lap and shoulder belts for the driver and restrain a child seat or secure a large item in a seat all seating positions Please pay close attention to th
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! • Never place a rear facing infant seat in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. • Only use a rearward-facing child restraint in a vehicle with a rear seat. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags. • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions have combination lap/shoulder belts.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Automatic Locking Retractor (ALR) Mode How To Disengage The Automatic Locking Mode In this mode, the shoulder belt is automatically pre- Unbuckle the combination lap/shoulder belt and allow it locked. The belt will still retract to remove any slack in to retract completely to disengage the Automatic Locking the shoulder belt. Mode and activate the vehicle sensitive (emergency) locking mode.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be This vehicle has a safety belt system with an Energy worn snugly and positioned properly. Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the air bags, the pretencollision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 (maximum six seconds of continuous chime). It stops The front passenger seat BeltAlert® is not active when after the end of the six second period or when the driver both the front passenger seats are unoccupied. BeltAlert® may be triggered when an animal or heavy object is on seatbelts becomes fastened. one or both of the front passenger seats.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The word AIRBAG is embossed on the air bag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: The Driver and Passenger Advanced Front Air NOTE: Bags are certified to the new Federal regulations for • Air Bag covers may not be obvious in the interior trim, Advanced Air Bags. but they will open during air bag deployment. This vehicle is equipped with a driver and/or front • After any collision, the vehicle should be taken to an passenger seat belt buckle switch that detects whether authorized dealer immediately.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Seat-Mounted Side Air Bags (SAB) • Supplemental Side Air Bag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Seat Belt Buckle Switch • Seat Belt Pretensioners Advanced Front Air Bag Features The Advanced Front Air Bag system has single stage driver and front passenger air bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Supplemental Seat-Mounted Side Air Bags (SAB) Supplemental Seat-Mounted Side Air Bags may provide enhanced protection to help protect an occupant during a side impact. The Supplemental Seat-Mounted Side Air Bag is marked with an air bag label sewn into the outboard side of the front seats. Supplemental Seat-Mounted Side Air Bag Label When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Air Bag Inflatable Curtain (SABIC) SABIC air bags may offer side-impact protection to front seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection. WARNING! • Your vehicle is equipped with SABIC air bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. Air Bag Deployment Sensors And Controls Knee Impact Bolsters The ORC determines if deployment of the front and/or side air bags in a frontal or side collision is required.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 The Advanced Front Air Bags will not deploy in all The ORC contains a backup power supply system that frontal collisions, including some that may produce sub- may deploy the air bags even if the battery loses power or stantial vehicle damage — for example, some pole colli- it becomes disconnected prior to deployment. sions, truck underrides, and angle offset collisions.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Based on the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating SAB exits through the seat seam into the space between the occupant and the door. The SAB fully inflate in about 10 milliseconds.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR. Child Restraints There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 NOTE: • For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents should refer to Transport Canada’s website for additional information: • http://www.tc.gc.ca/eng/roadsafety/ safedrivers-childsafety-index-53.htm WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearwardreach the highest weight or height allowed by their facing in the vehicle until they are two years old or until they convertible child seat. reach either the height or weight limit of their rear facing child safety seat.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children And Child Restraints Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forwardfacing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Children Too Large For Booster Seats 5. Can the child stay seated like this for the whole trip? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints In Commercial Vehicles This commercial vehicle is not designed for use as a family vehicle and is not intended for carrying children in the front passenger seat(s). Never install rearwardfacing child restraints in this vehicle. Although the seat belt can be locked to secure a child restraint, there are no tether anchorages to complete the proper installation of a forward-facing child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 into the retractor. For additional information on ALR, refer to the “Automatic Locking Mode” description under “Occupant Restraints.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR) out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 1. Place the child seat in the center of the seating position. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 FUEL CUT OFF SWITCH WARNING! The vehicle is fitted with a safety switch that, in the event of an accident, comes into operation by cutting off the If, after a crash, you smell fuel or see leaks from the fuel supply and turning off the engine as a consequence. fuel system, do not reset the switches to avoid the risk of fire.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Safety Checks You Should Make Inside The Vehicle Seat Belts not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Swivel Seat — If Equipped. . . . . . . . . . . . . . . .82 ▫ Inside Day/Night Mirror — If Equipped . . . . .72 ▫ Flap On Bench — If Equipped . . . . . . . . . . . . .83 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .84 ▫ Outside Mirrors Folding Feature . . . . . . . . . . .73 ▫ Head Restraints . . . . . .
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights — If Equipped . . . . . .91 ▫ Intermittent Wiper System . . . . . . . . . . . . . . .95 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .92 ▫ Low Speed . . . . . . . . . . . . . . . . . . . . . . . . . . .96 ▫ Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . .92 ▫ High Speed . . . . . . . . . . . . . . . . . . . . . . . . . .96 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . .92 ▫ Mist Feature . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 䡵 PARKSENSE® REAR PARK ASSIST — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .102 ▫ ParkSense® Rear Park Assist Sensors. . . . . . . .102 䡵 POWER OUTLETS — IF EQUIPPED. . . . . . . . . .111 䡵 CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .114 ▫ ParkSense® Rear Park Assist Alerts . . . . . . . . .103 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex mirror. Power Mirrors — If Equipped The power mirror controls are located on the driver-side door trim panel.
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE switch. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position “O” to prevent accidentally moving a mirror. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 If the mirror head or pivot exhibits a slight amount of play, the mirror should be power folded closed, then power folded open (This may require multiple button pushes). NOTE: The intended use of the power fold mirrors is by pushing the buttons to fold and unfold the mirrors. Only manually fold the mirrors when necessary. 3 Forward Folding Mirrors can be folded forward manually or by accidental impact.
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Seats are a part of the Occupant Restraint System of the The driver and passenger seats can be adjusted forward, vehicle. rearward, reclined, front and rear height and lumbar adjustments. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Forward And Rearward Adjustment The adjusting bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Height Adjustment — Without Swivel Seat — If Equipped The height adjusting levers are located on the center outboard side of the seat. Lift up on the front lever to adjust the front of the seat up or down. Lift up on the rear lever to adjust the rear of the seat up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Height Adjustment — With Swivel Seat — If Equipped The height adjusting knobs are located on the center outboard side of the seat. Rotate the front knob to adjust the front of the seat up or down. Rotate the rear knob to adjust the rear of the seat up or down.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recliner Adjustment — Without Swivel Seat The recliner knob is on the rear outboard side of the seat. To recline the seatback, lean back, rotate the knob rearward to position the seatback as desired. To return the seatback to its normal upright position, lean forward, rotate the knob forward until the seatback is in the upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Recliner Adjustment — With Swivel Seat The recliner lever is located at the lower front outboard side of the seat. To recline the seatback, lean forward slightly, pull the lever outward, lean back to the desired position and release the lever. To return the seatback to its normal upright position, lean forward and pull the lever outward. Release the lever once the seatback is in the upright position.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Air Seat — If Equipped The seat is equipped with a mechanical spring system and hydraulic shock absorber to ensure maximum comfort and safety. The system of springs also effectively absorbs impact from uneven road surfaces. Damper Weight Adjustment Use the weight adjustment knob to set the required setting based on body weight, with settings between 88 lbs (40 kg) and 286 lbs (130 kg).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 driving position or at the 180° position. To swivel the Flap On Bench — If Equipped seat, pull the swivel seat lever outward, turn the seat to If your vehicle is equipped with a bench seat, the seat is the desired position and release the lever. equipped with a fold-down flap that can be used as a document support surface. To use the fold-down flap, grasp the pull tab and lower the flap.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The fold-down flap is equipped with two cup holders Heated Seats — If Equipped and a support surface with a paper holder clip. On some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the lower outboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Press the switch once to turn on the heated seats. Press the switch a second time to shut the heating elements off. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Front Head Restraints To raise the head restraint, pull upward on the head Adjustment Button restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Adjustable Armrests — If Equipped The seat adjustable armrest can be raised and adjusted for height. Underneath the front of the armrest is the adjuster wheel which will adjust the height of the armrest up or down. Turn the adjuster wheel to the right or left to adjust the height of the armrest up or down.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle, reach into the opening beneath the center of the hood and push the To open the hood, two latches must be released. safety latch lever to the right to release it, before 1. Open the drivers door to gain access to the hood raising the hood. release lever. Pull the hood release lever located on the side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 3. Raise the hood and place the hood prop rod in hood slot to secure the hood in the open position. CAUTION! To prevent possible damage: • Before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. • Do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights To turn on the headlights, turn the end of the multifunction lever to the headlight position. The multifunction lever controls the operation of the When the headlight switch is on, the parking headlights, parking lights, turn signals, headlight beam lights, taillights, license plate light, the clearselection and the passing lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Dimmer Controls Daytime Running Lights — If Equipped The dimmer controls are located on the left side of the NOTE: When the headlights are turned on, the Daytime instrument panel below the instrument cluster. Running Lights will be deactivated. To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O (Off) position. NOTE: The low beams and side/taillights will not be on with DRL.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-On Reminder Fog Lights — If Equipped If the headlights or parking lights are not turned OFF when the ignition is turned OFF a chime will sound to alert the driver when the driver’s door is opened. The fog light switch is located on the center stack of the instrument panel, just below the climate controls. Press the switch once to turn the fog lights on. Press the switch a second time to turn the fog lights off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Parking Lights Flash-To-Pass These lights can only be turned on with ignition key in the STOP position or removed, by moving the end of the multifunction lever to O (off) position and then to the headlight position. You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE comes on when the lever is operated and stays on until the Right Switch function is automatically deactivated. Each movement of the • Press the right switch to the left to turn ON the left lever only increases the amount of time the lights stay on. map light. • Press the right switch to the right to turn ON the right Deactivation map light. Pull the multifunction lever toward the steering wheel and hold it for more than two seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 WINDSHIELD WIPERS AND WASHERS Windshield Wipers The windshield wiper/washer lever is located on the right side of the steering column. There are five different modes of operation for the front windshield wipers. The windshield wiper lever can be raised or lowered to access the modes. 3 NOTE: The windshield wipers/washers will only operate with the ignition in the ON/RUN position.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Low Speed Windshield Washer Operation Push the lever downward to the second detent. The To use the washer, pull the windshield wiper/washer wipers will operate at low speed. lever toward the steering wheel to activate the washers. The wipers will activate automatically for three cycles High Speed after the lever is released. and then resume the intermitPush the lever downward to the third detent. The wipers tent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 To unlock the steering column, pull the control handle This feature allows you to lengthen or shorten the up. To lengthen or shorten the steering column, pull the steering column. The telescoping control handle is lo- steering wheel outward or push it inward as desired. To lock the steering column in position, push the control cated below the steering wheel at the end of the steering handle down until fully engaged. column.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h) up to the maximum speed of 100 mph (160 km/h). The Electronic Speed Control Lever is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by rotating the Electronic Speed Control ON/OFF center ring and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: A soft tap on the brake pedal, pushing the RES button, or normal brake pressure while slowing the vehicle will U.S. Speed (mph) deactivate Electronic Speed Control without erasing the • Tapping the Speed Control lever up (+) once will result set speed memory. Rotating the center ring upward to in a 1 mph increase in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • If the lever is continually held down, the set speed will continue to decrease until the lever is released, then When the Electronic Speed Control is set, you can decrease the new set speed will be established. speed by tapping the Speed Control lever down (-). The speed decrement shown is dependant on the speed To Accelerate For Passing To Decrease Speed of U.S. (mph) or Metric (km/h) units: U.S. Speed (mph) Press the accelerator as you would normally.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 (60 cm) from the corners of the rear fascia/bumper, The minimum height of a detectable obstacle corredepending on the location, type and orientation of the sponds to the maximum height of an obstacle that would clear the underside of the car during the parking maneuobstacle. ver. ParkSense® Rear Park Assist Alerts If an obstacle is behind the vehicle when REVERSE gear is engaged, an audible alert is activated.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Audible And Visual Signals Supplied By The ParkSense® Rear Park Assist System SIGNAL Obstacle Distance MEANING An obstacle is present within the sensors’ field of view Failure Sensor or System failures INDICATION Audible signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases as the distance decreases. • Emits continuous tone at 12 in (30 cm). • Adjustable volume level programmable through personal settings in the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 While audible signals are emitted, the audio system is not The sensors and wiring are tested continuously when the ignition is in the ON/RUN position. Failures are indimuted. cated immediately if they occur when the system is ON. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the Even if the system is able to identify that a specific sensor distance measured by the inner sensors is constant.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Objects such as bicycle carriers, etc., must not be placed within 12 in (30 cm) from the rear fascia/ bumper while driving the vehicle. Failure to do so can NOTE: result in the system misinterpreting a close object as a sensor problem, causing a failure indication to be • Ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt displayed in the instrument cluster.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 CAUTION! (Continued) WARNING! (Continued) • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense®. • Before using ParkSense®, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 When displayed, static grid lines will illustrate the width following table shows the approximate distances for each of the vehicle and will show separate zones that will help zone: indicate the distance to the rear of the vehicle.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView® to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using ParkView®. Map/Dome/Lights These lights are mounted between the sun visors on the overhead console. Each light is turned on by pressing the corresponding switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • Press the right switch to the right to turn ON the right POWER OUTLETS — IF EQUIPPED map light. Passenger Compartment Power Outlet The cigar lighter and the power socket are located in the center console. It only operates with the ignition key at MAR/ON.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Load Compartment Power Outlet The Load Compartment Power Outlet is located on the left rear side of the rear cargo compartment. The outlet can be is used for powering 12 Volt adaptive accessories and recharging communications devices. NOTE: Do not connect devices with power higher than 180 W to the socket. Do not damage the socket by using unsuitable adaptors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED CUPHOLDERS The cupholders for the drivers and passenger area are A removable ash receiver and cigar lighter are available. located near the floor just under the center stack storage compartment. There are cupholders located in each door panel as well as one single cupholder located to the right of the manual climate controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 STORAGE Front Door Storage — If Equipped Glove Compartments Storage areas and bottle holders are located in both the front door trim panels. The glove compartments are located on the right side of the instrument panel.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dash Storage Dashboard Clipboard The dash storage is located on the right side of the Located on top of the dashboard is a clipboard and two instrument panel. storage bins on each side of the clipboard.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 CARGO AREA FEATURES Cargo Area The cargo area may be equipped with different options such as a optional side panels, rear seats and an optional floor.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .121 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . .143 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .123 ▫ Values Displayed . . . . . . . . . . . . . . . . . . . . . .143 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .124 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . .144 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . .
120 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Uconnect® RH3 Display. . . . . . . . . . . . . . . . .149 䡵 Uconnect® RADIOS . . . . . . . . . . . . . . . . . . . . .172 ▫ General Functions And Settings . . . . . . . . . . .150 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . . ▫ Tuner Mode (AM/FM Radio) . . . . . . . . . . . . .153 ▫ USB Charging Port . . . . . . . . . . . . . . . . . . ▫ Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 121 INSTRUMENT PANEL FEATURES 4
122 UNDERSTANDING YOUR INSTRUMENT PANEL 1 — Air Outlet 2 — Multifunction Lever (External Lights) 3 — Instrument Cluster 4 — Multifunction Lever (Front/Rear Wiper, Trip Computer) 5 — Radio 6 — Clip Board 7 — Upper Glove Compartment 8 — Passenger Air Bag 9 — Storage Compartment 10 — Lower Glove Compartment 11 — Cup Holder 12 — USB Charger/12V 13 — Climate Controls 14 — Lower Switch Bank 15 — Cup Holders 16 — Shift Lever 17 — USB / AUX 18 — Ignition Switch 19 — Uconnect® Phone Buttons 20 — Tilt Steering Col
UNDERSTANDING YOUR INSTRUMENT PANEL 123 INSTRUMENT CLUSTER 4
124 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 3. Stop Light Failure Indicator 1. Speedometer This light will illuminate if one or more of the stop light The speedometer shows the vehicle speed in miles per bulb fails. The failure relating to this light could be: one or more hour (mph) and/or kilometers per hour (km/h). blown bulbs, a blown protection fuse or a break in the 2. Turn Signal Indicators electrical connection. The arrow will flash with the exterior turn 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ 6.
126 UNDERSTANDING YOUR INSTRUMENT PANEL 8. External Light Failure Indicator — If Equipped 9. Door Ajar Indicator The External Light Failure Indicator will come on when a failure to one of the following lights is detected: • Side Marker Lights • Brake Lights • Direction Indicators • Backup Lights • Parking Lights • Headlights • Tail Lights • D.R.L. • Clearance Lights • License Plate Lights This indicator will illuminate when one or more door(s) are not fully closed. 10.
UNDERSTANDING YOUR INSTRUMENT PANEL 127 11. Tachometer 14. Charging System Light — If Equipped The tachometer indicates engine speed in Revolutions Per Minute (RPM x 1000). This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the Charging System light remains on, or comes on while driving, it means that the vehicle is experiencing a problem with the charging system.
128 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop.
UNDERSTANDING YOUR INSTRUMENT PANEL 129 Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. turned on and remain on, as a bulb check, until the engine is started.
130 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. 17. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 131 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle.” Follow the warnings under the “Cooling System Pressure Cap” paragraph. 18. Engine Temperature Warning Light This light warns of an overheated engine condition.
132 UNDERSTANDING YOUR INSTRUMENT PANEL when the engine is running, immediate service is re- 22. Fuel Gauge/Fuel Door Reminder quired and you may experience reduced performance, an When the ignition switch is in the ON/RUN elevated/rough idle or engine stall and your vehicle may position, the pointer will show the level of fuel require towing. The light will come on when the ignition remaining in the fuel tank.
UNDERSTANDING YOUR INSTRUMENT PANEL 133 placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the This light will turn on for four to eight seconds vehicle placard or tire inflation pressure label, you should as a bulb check when the ignition switch is first determine the proper tire inflation pressure for those turned to ON/RUN. If the light is either not on tires.
134 UNDERSTANDING YOUR INSTRUMENT PANEL maintain correct tire pressure, even if under-inflation has replacement or alternate tires and wheels allow the TPMS not reached the level to trigger illumination of the TPMS to continue to function properly. low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL 135 26. Seat Belt Reminder Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver or front passenger(s) seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger(s) seat belt remains unbuckled, the seat belt reminder light will flash or remain on continuously.
136 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on momentarily each time the ignition switch is turned to ON/RUN. 29. Anti-Lock Brake (ABS) Light This light monitors the Anti-lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 137 30. Vehicle Security Light If during starting, the key code is not correctly recognized, the Vehicle Security Light comes on in the instrument panel. In this case, turn the key to OFF and then to ON/RUN; if it is still locked, try again with the other keys that come with the vehicle. Contact an authorized dealer if you still cannot start the engine.
138 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Time • Set Date • Auto Clock The system allows the driver to select information by pressing the following buttons mounted on the instrument panel to the left of the steering column: • Units • Languages • Buzzer Volume • Seat Belt Buzzer (*) • (*) just available after SBR disable made by CHR Service • Service (Diesel Only) • DRL - Daytime Running Light (if equipped) • Exit Menu EVIC Control Buttons • MODE Button Push and HOLD the MODE button for a time longe
UNDERSTANDING YOUR INSTRUMENT PANEL 139 submenu screens of a main menu item. Press and hold Electronic Vehicle Information Center (EVIC) the MODE button for two seconds to reset displayed/ Setup Menu selected features that can be reset. The menu comprises a series of functions arranged in a cycle. Push the UP and DOWN buttons to access • UP Arrow Button the different options and settings (setup).
140 UNDERSTANDING YOUR INSTRUMENT PANEL • Language • Buzzer Volume Selecting An Option Of The Main Menu Without Submenu 1. Briefly press the MODE button to select the main • Seat Belt Buzzer (*) menu option to set. • (*) just available after SBR disable made by CHR or DOWN button (by single 2. Press the UP Service presses) to select the new setting. • Service (Diesel Only) 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 4. Press the UP or DOWN button (by single Unless reset, this message will continue to display each presses) to select the new setting for this submenu time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and option. release the MODE button. To reset the oil change indi5.
142 UNDERSTANDING YOUR INSTRUMENT PANEL • When the “Trip distance” reaches 99999.9 miles or kilometers or when the “Travel time” reaches 999.59 The Trip Computer is located in the instrument cluster. It (999 hours and 59 minutes), the system is reset autofeatures a driver-interactive display (displays informamatically. tion such as; trip information, range, fuel consumption, average speed and travel time). • Disconnecting/Reconnecting the battery resets the system.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 Briefly push the MENU button to go back to the menu “Trip B” can be used to display the figures relating to: screen or push and hold the MENU (approximately one • Trip distance B second) to go back to the main screen without storing • Average consumption settings. Trip Functions • Average speed B Both trip functions are resettable (reset — start of new • Travel time B (driving time) trip).
144 UNDERSTANDING YOUR INSTRUMENT PANEL • The vehicle is parked for a long time with the engine Average Speed running. This value shows the vehicle’s average speed as a funcNOTE: The range depends on several factors: driving tion of the overall time elapsed since the last reset. style, type of route (freeway, residential, mountain roads, Travel Time etc.), conditions of use of the car (load, tire pressure, etc.). This value shows the time elapsed since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 • Buzzer Volume Uconnect® RH3 • Seat Belt Buzzer (*) Introduction • (*) just available after SBR disable made by CHR Your vehicle is equipped with a radio that has an Service AM/FM radio receiver and a USB port for playing MP3, WMA and AAC files. The device has been designed • Service (Diesel Only) according to the specific characteristics of the vehicle, • DRL - Daytime Running Light (if equipped) with a design matching the style of the instrument panel.
146 UNDERSTANDING YOUR INSTRUMENT PANEL Recommendations Road Safety We recommend that you learn how to use the various radio features (for example, Station Preset) before you begin your journey. WARNING! Turning the volume up too high may be dangerous for the driver and other people on the road. You should adjust the volume so that you are always able to hear sounds around you (e.g. horns, ambulances, police cars, etc.).
UNDERSTANDING YOUR INSTRUMENT PANEL 147 Identification Number The radio has a unique identification number (found on the warranty card). This card is required as proof of ownership if the radio is stolen or when seeking assistance. Do not store the warranty card in the vehicle. Security Code This radio has a serial number (found on the ⬙warranty card⬙). Present this card as proof of ownership if the radio is stolen or if you require assistance. Do not store the warranty card in the vehicle.
148 UNDERSTANDING YOUR INSTRUMENT PANEL Action Press 䉳䉳 or 䉴䉴 to move to the fourth digit. Turn the ROTARY knob to select the fourth digit When you finish entering the code, press the ROTARY knob to accept the code entered.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 General Uconnect® RH3 Display • Separate BASS and TREBLE settings • BALANCE/FADE (balances left/right and front/rear channels) • Equalizer • Loudness 4 • Digital clock in 24-hour format with weekday setting • Illuminated buttons and display • LCD display • Extended functions field (Setup MENU) allows you to change the default settings Display Panel Description Of Commands Rotary Knob: Turn radio on and off, volume, forward/ reverse track, confirm selected optio
150 UNDERSTANDING YOUR INSTRUMENT PANEL 䉴䉴 And 䉳䉳 Buttons: Station search in automatic mode, Band/AS Button: Select tuned frequency band, preset station search in manual mode, forward/reverse tracks, best stations. forward/reverse within track. Menu Button: Access setup menu. Mute/Pause Button: Interrupts the sound by muting or General Functions And Settings pausing the audio. Turn The Radio On Or Off DISP Button: Switches between display modes, clock display.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 If you prefer, you can set ⬙Auto Switch⬙ to ⬙ON⬙ (see SETUP MENU section). The radio will then follow two parameters: ignition and previous state. If the ignition is turned off with the radio on, the radio will be turned off, but will come on again when the ignition is turned on. not pressed again within five seconds, or if you press the ROTARY knob, the display returns to the previously selected view and the settings will be saved.
152 UNDERSTANDING YOUR INSTRUMENT PANEL ROTARY knob clockwise. To decrease the bass level, turn Fader the ROTARY knob counterclockwise. The bass levels can The display will show ⬙FAD 00⬙ to indicate that you can be set between -15 and 15. set the Fader function. Turn the ROTARY knob clockwise to transfer the sound to the front; the display will show Treble ⬙FAD F 01⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 radio is searching for the new station, the display will show ⬙SEEKING⬙. When the search is complete, the When you enter TUNER mode, the radio tunes to the display will show the tuned frequency band and most recently selected station and will remain on the station in the format ⬙F1 106.9⬙ or, if the station was most recently selected frequency band.
154 UNDERSTANDING YOUR INSTRUMENT PANEL the station found was previously stored in memory, Turn the ROTARY knob to restore the audio and change the display will show the channel where it is stored the volume to the level selected. The display will show and the tuned station. the settings described in the volume function. The other buttons should be implemented when pressed, Pressing this button mutes the sound. The display will but the radio will remain in ⬙MUTE ON⬙ mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 Accessing Preset Stations When the preset buttons (1 through 6) are pressed for less than two seconds the radio will tune in to the station associated with that particular memory location. The display shows the preset number and frequency of the associated station for three seconds. The display will then return to the previous view.
156 UNDERSTANDING YOUR INSTRUMENT PANEL indicating the maximum volume selected. When the maximum volume selected is the maximum radio volYou can use the Setup menu to change the various factory ume, the display will show ⬙MVOL OFF⬙. settings to suit your own preferences. Auto Switch Press MENU to activate the Maximum Volume function.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 Clock Pressing the DISP button for more than two seconds enables or disables the clock display. When this feature is enabled, the display shows ⬙CLK ON⬙ and the clock is displayed whenever the ignition is switched on, even if the radio is off. This function takes priority in the display whenever you access any of the radio functions. If no buttons are pressed within 10 seconds, the display will go back to showing the clock.
158 UNDERSTANDING YOUR INSTRUMENT PANEL In USB mode, the radio plays MP3, WMA and AAC files If playable files are found, the radio will also check that stored on the device connected to the USB port that is the connected device is the same as the one used immediately before the USB function. If this is the case, music located inside the glove compartment of the vehicle. playback will start from the point where it was interTo enter USB mode, you must press the SRC button. rupted (file and music runtime).
UNDERSTANDING YOUR INSTRUMENT PANEL 159 4
160 UNDERSTANDING YOUR INSTRUMENT PANEL Play Sequence 1 2 3 4 5 6 7 8 9 10 (File) Track 1_1 Track Track Track Track Track Track Track Track Track 2_1 3_1 4_1 4_2 5_1 5_2 5_3 5_4 6_1 Comments If there are MP3, WMA or AAC (extensions mp3, wma, m4a, mp4 and 3gp) files in the root folder, these will be played first. Folders within the same level are sorted in ascending order by name (up to folder number 100, after which the order follows that in which they were recorded on the USB device).
UNDERSTANDING YOUR INSTRUMENT PANEL 161 Forward/Reverse track for less than two seconds, the radio When you press will advance to the next audio file on the device. When for less than two seconds, the radio will you press skip back to the beginning of the track. If this button is pressed again, the radio will skip back to the previous audio file on the device. When these buttons are pressed, the display will show a ⬙TRKyyy⬙ message, where yyy is the track number.
162 UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the F-TRACK button will not resume play, but using the (F-TRK + rotation) function will start or resume Pressing this knob stops music playback and mutes the play. sound. The display will switch between ⬙PAUSED⬙ and The other buttons should be implemented when pressed, the current view (three seconds). but the radio will remain in ⬙Mute/Paused⬙ mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 When the ROTARY knob is pressed or if its position is not changed for five seconds, the track is selected, the ID3 tag is processed and the music will start playing. In this case, the display will show the ⬙TRKyyy⬙ message for two seconds and then return to the default display defined by the DISP function.
164 UNDERSTANDING YOUR INSTRUMENT PANEL Whenever the radio skips from one folder to another, the display will show the name of the folder to which you are going for a few milliseconds (the rotary movements are ignored during this period) and a maximum of three seconds. When you reach the last folder and press Button 1 again, the radio will advance to the next folder on the USB device. When you reach the first folder and press Button 2 again, the radio will advance to the next folder on the USB device.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 Uconnect® SETTINGS The Uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable features. 4 Uconnect® 5.
166 UNDERSTANDING YOUR INSTRUMENT PANEL Hard-Keys Customer Programmable Features — Uconnect® Hard-Keys are located below the Uconnect® system in 5.0/5.0N Settings the center of the instrument panel. In addition, there is a Press the Settings hard-key to display the menu setting Scroll/Enter control knob located on the right side. Turn screen. In this mode the Uconnect® system allows you to the control knob to scroll through menus and change access programmable features that may be equipped settings (i.e.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 settings screen. Pressing the Up or Down Arrow soft-keys language, showing that setting has been selected. Touch on the right side of the screen will allow you to toggle up the arrow back/Done soft-key to return to the previous menu. or down through the available settings.
168 UNDERSTANDING YOUR INSTRUMENT PANEL • Touchscreen Beep and/or PM soft-key until a check-mark appears next to the setting, showing that setting has been selected. Touch When in this display, you may turn on or shut off the the arrow back/Done soft-key to return to the previous sound heard when a touch screen button (soft-key) is menu. If 24h is selected, AM/PM soft-keys will be greyed pressed. Touch the Touchscreen Beep soft-key until a out (unavailable).
UNDERSTANDING YOUR INSTRUMENT PANEL 169 To make your selection, touch the ParkView® Rear Back Up Camera soft-key, until a check-mark appears next to After pressing the Safety/Assistance soft-key the followsetting, indicating that the setting had been selected. ing settings will be available: Touch the arrow back/Done soft-key to return to the • ParkView® Rear Back Up Camera — If Equipped previous menu.
170 UNDERSTANDING YOUR INSTRUMENT PANEL Doors & Locks • Equalizer After pressing the Doors & Locks soft-key the following When in this display you may adjust the Bass, Mid and settings will be available: Treble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale • Auto Door Locks between the + and – soft-keys. Then touch the arrow When this feature is selected, all doors will automatically back/Done soft-key. lock when the vehicle is in motion.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 • Loudness — If Equipped Phone/Bluetooth® The Radio automatically turns on when vehicle is in run After pressing the “Phone/Bluetooth” soft-key the folor will recall whether it was on or off at last ignition off. lowing settings will be available: To make your selection, touch the Loudness soft-key, • Paired Devices select On or Off followed by pressing the arrow back/ This feature shows which phones are paired to the Done soft-key. Phone/Bluetooth® system.
172 UNDERSTANDING YOUR INSTRUMENT PANEL • Subscription Information Restore Settings New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 iPod®/USB/MP3 CONTROL — IF EQUIPPED The USB Input and Auxiliary Jack is located on the instrument panel left of the radio (driver’s lower right). This feature allows an iPod® or external USB device to be plugged into the USB port. iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features. Please visit Apple’s website for software updates.
174 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the device battery to be charged is completely The USB connector port can be used for charging pur- depleted, it may take awhile to charge. poses only. Use the connection cable to connect an iPod® WARNING! or external USB device to the vehicle’s USB charging port which is located next to the 12V power outlet near the Do not plug in or remove the iPod® or external cup holder on passenger side. device while driving.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 The left-hand control is a rocker-type switch and controls the volume of the sound system plus a button to mute the The remote sound system controls are located on the Sound System. surface of the steering wheel. The following describes the right-hand control operation in each mode.
176 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper or tape to the disc; avoid scratch- RADIO OPERATION AND MOBILE PHONES ing the disc. Under certain conditions, the mobile phone being on in 4. Do not use solvents such as benzene, thinner, cleaners, your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated or anti-static sprays. by relocating the mobile phone. This condition is not 5. Store the disc in its case after playing.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 CLIMATE CONTROLS Manual Heating And Air Conditioning The Manual Temperature Controls consist of a series of three outer rotary dials (blower speed, temperature and mode) and three inner push buttons (Recirculation, A/C, Rear Window Defroster). Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position.
178 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Mode Control (Air Direction) Rotate this control to choose from several patterns of air distribution. You can select either a primary mode as identified by the symbols on the control, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution you receive from that mode. • Panel • Bi-Level Air is directed through the panel and floor outlets.
180 UNDERSTANDING YOUR INSTRUMENT PANEL • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Air is directed through the floor, defrost, and side Extended use of this mode is not recommended. window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the • The use of the Recirculation mode in cold or damp windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 • Hot Ambient Temperature. • Blower at Maximum speed. If equipped, press the Rear Defrost button to activate defrosting of door mirrors and heated nozzles. NOTE: Do not affix stickers to the inside of the heated • In case of hot ambient temperature, the recirculation is rear window over the heating filaments, to avoid damage closed (opened for a minute each 15 minutes so the air that might cause them to stop working properly.
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .186 ▫ Six-Speed Automatic Transmission . . . . . . . . .191 ▫ Automatic Transmission — If Equipped . . . . .186 䡵 DRIVING ON SLIPPERY SURFACES . . . . . . . . .201 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .186 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . .201 ▫ Extreme Cold Weather (Below –20°F Or −29°C) . . . . . . . . . . . . . . . .187 ▫ Traction . . . . . . . . . . . . . . . .
184 STARTING AND OPERATING 䡵 BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . .208 䡵 TIRES — GENERAL INFORMATION . . . . . . . .230 ▫ Four-Wheel Anti-Lock Brake System (ABS) . . .208 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .230 䡵 ELECTRONIC BRAKE CONTROL SYSTEM . . . .209 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .231 ▫ Traction Control System (TCS) . . . . . . . . . . . .210 ▫ Tire Pressures For High Speed Operation . . . .
STARTING AND OPERATING 185 䡵 TIRE ROTATION RECOMMENDATIONS . . . . .243 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . .254 䡵 TIRE PRESSURE MONITORING SYSTEM 䡵 ADDING FUEL . . . . . . . . . . . . (TPMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 ▫ Fuel Filler Cap (Gas Cap) . . . ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . .247 ▫ Loose Fuel Filler Cap Message ▫ General Information . . . . . . . . . . . . . . . . . . .249 䡵 VEHICLE LOADING . . . . . . . .
186 STARTING AND OPERATING STARTING PROCEDURES Automatic Transmission — If Equipped Before starting your vehicle, adjust your seat, adjust both The shift lever must be in the PARK or NEUTRAL inside and outside mirrors, and fasten your seat belts. position before you can start the engine. Depress the brake pedal before shifting to any driving gear. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
STARTING AND OPERATING 187 Extreme Cold Weather (Below –20°F Or −29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
188 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. WARNING! Remember to disconnect the engine block heater cord before driving.
STARTING AND OPERATING 189 WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
190 STARTING AND OPERATING WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector. • Do not leave the ignition key in or near the vehicle (or in a location accessible to children).
STARTING AND OPERATING 191 Six-Speed Automatic Transmission The transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of PARK (Refer to “Brake/Transmission Shift Interlock System” in this section). To drive, move the shift lever from PARK or NEUTRAL to the DRIVE position. The electronically-controlled transmission provides a precise shift schedule.
192 STARTING AND OPERATING The transmission shift lever has PARK, REVERSE, NEUTRAL, DRIVE, and Electronic Range Select (ERS) shift positions. Manual downshifts can be made using the ERS shift control (refer to “Electronic Range Select (ERS) Operation” in this section for further information). Moving the shift lever into the ERS (-/+) position (beside the DRIVE position) displays the current gear in the instrument cluster, and prevents automatic upshifts beyond this gear.
STARTING AND OPERATING 193 When parking on a hill, apply the parking brake before shifting the transmission to PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade. WARNING! • Never use the PARK position as a substitute for the parking brake.
194 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the ignition key. Once the key is removed, the transmission is locked in PARK, securing the vehicle against unwanted movement.
STARTING AND OPERATING 195 • Look at the transmission gear position display and REVERSE (R) verify that it indicates the PARK position. This range is for moving the vehicle backward. Shift into • With the brake pedal released, verify the shift lever REVERSE only after the vehicle has come to a complete stop. will not move out of PARK. CAUTION! • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal.
196 STARTING AND OPERATING CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information. DRIVE (D) This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy.
STARTING AND OPERATING 197 Transmission Limp Home Mode 3. Turn the ignition switch to the OFF position. Transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, Transmission Limp Home Mode is activated. In this mode, the transmission remains in third gear regardless of which forward gear is selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated.
198 STARTING AND OPERATING Once in ERS mode, moving the shift lever forward (-) or rearward (+) will change the top available gear. Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows the driver to limit the highest available gear. For example, if To exit ERS mode, simply return the shift lever to the you shift the transmission into 4 (fourth gear), the DRIVE position.
STARTING AND OPERATING 199 NOTE: To select the proper gear position for maximum deceleration (engine braking), move the shift lever into the ERS position, then tap it forward (-) repeatedly as the vehicle slows. The transmission will shift to the range from which the vehicle can best be slowed down. When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode.
200 STARTING AND OPERATING Torque Converter Clutch seem as if the transmission is not shifting properly when cold. This is normal. Using the Electronic Range Select (ERS) shift control, when the transmission is sufficiently warm, will demonstrate that the transmission is able to shift into and out of Overdrive. A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds.
STARTING AND OPERATING 201 DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
202 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle. and Warnings before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 203 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
204 STARTING AND OPERATING • Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. The standard power steering system will give you good This is due to the cold, thick fluid in the steering vehicle response and increased ease of maneuverability system. This noise should be considered normal, and it in tight spaces. The system will provide mechanical does not in any way damage the steering system. steering capability if power assist is lost.
STARTING AND OPERATING 205 Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
206 STARTING AND OPERATING PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. The parking brake lever is located on the outboard side of the drivers seat. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the side button with your thumb, then lower the lever completely.
STARTING AND OPERATING 207 When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
208 STARTING AND OPERATING CAUTION! If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Four-Wheel Anti-Lock Brake System (ABS) The Four-Wheel ABS is designed to aid the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING 209 WARNING! • Pumping the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
210 STARTING AND OPERATING Traction Control System (TCS) The Traction Control System (TCS) monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced, to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential, and controls the wheel spin across a driven axle.
STARTING AND OPERATING 211 Brake Assist System (BAS) The Brake Assist System (BAS) is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
212 STARTING AND OPERATING Electronic Stability Control (ESC) The Electronic Stability Control (ESC) enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
STARTING AND OPERATING 213 ESC will operate without engine torque management. This mode is intended to be used if the vehicle is in deep snow, The “ESC Off” switch is located in the center sand or gravel conditions and more wheel spin than ESC switch bank, next to the hazard flasher switch. would normally allow is required to gain traction. To turn ESC on again, momentarily press the “ESC Off” switch. This will restore the normal “ESC On” mode of operation.
214 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch. Once the situation requiring ESC to be switched to the “Partial Off” mode is overcome, turn ESC back on by momentarily pressing the “ESC Off” switch. This may be done while the vehicle is in motion.
STARTING AND OPERATING 215 • Each time the ignition is turned ON, the ESC system all trailers from swaying. Always use caution when towing a trailer and follow the trailer tongue weight will be ON even if it was turned off previously. recommendations. Refer to “Trailer Towing” in this sec• The ESC system will make buzzing or clicking sounds tion for further information. When TSC is functioning, when it is active.
216 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backThe HSA system is designed to assist the driver when ing uphill is in REVERSE gear). starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short HSA will work in REVERSE and all forward gears when period of time after the driver takes their foot off of the the activation criteria have been met.
STARTING AND OPERATING 217 Towing With HSA WARNING! (Continued) HSA will provide assistance when starting on a grade when pulling a trailer. WARNING! • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
218 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 219 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ...
220 STARTING AND OPERATING EXAMPLE: 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 221 EXAMPLE: Load Identification: ⴖ....blank....
222 STARTING AND OPERATING Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
STARTING AND OPERATING 223 EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
224 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 225 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
226 STARTING AND OPERATING Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 227 The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed The vehicle maximum load on the tire must not exceed the weight referenced here. the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you Steps For Determining Correct Load Limit adhere to the loading conditions, tire size, and cold tire 1.
228 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
STARTING AND OPERATING 229 5
230 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 231 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
232 STARTING AND OPERATING • Inspect tires for signs of tire wear or visible damage. CAUTION! Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
STARTING AND OPERATING 233 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
234 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
STARTING AND OPERATING 235 If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode.
236 STARTING AND OPERATING rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT” in “What To Do Compact Spare Tire — If Equipped In Emergencies” for further information.
STARTING AND OPERATING 237 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life.
238 STARTING AND OPERATING WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 239 These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer replaced. to “Replacement Tires” in this section for further information.
240 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 241 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
242 STARTING AND OPERATING TIRE CHAINS (TRACTION DEVICES) Use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • Traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • Install on Front Tires Only • Tire chains for a 225/75R16 tire with a Quality Chain Corp Light Truck Highway Service (Non-Cam) tire chain or equivalent is recommended.
STARTING AND OPERATING 243 CAUTION! (Continued) • Observe the traction device manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • Do not use traction devices on a compact spare tire. TIRE ROTATION RECOMMENDATIONS The tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions.
244 STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire Rotation TIRE PRESSURE MONITORING SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12° F (6.5° C).
STARTING AND OPERATING 245 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold tire pressure on the placard.
246 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING 247 • Driving on a significantly under-inflated tire causes Base System the tire to overheat and can lead to tire failure. This is the TPMS warning indicator located in the Under-inflation also reduces fuel efficiency and tire instrument cluster. tread life, and may affect the vehicle’s handling and The TPMS uses wireless technology with wheel rim stopping ability. mounted electronic sensors to monitor tire pressure lev• The TPMS is not a substitute for proper tire mainte- els.
248 STARTING AND OPERATING the “Tire Pressure Monitoring Unavailable” text message will display. If the ignition key is cycled, this sequence The Tire Pressure Monitoring Telltale Light will illumiwill repeat providing the system fault still exists. The Tire nate in the instrument cluster, an audible chime will be Pressure Monitoring Telltale Light will turn off when the activated, and the “Check tire pressure” text message will fault condition no longer exists.
STARTING AND OPERATING 249 1. The spare tire does not have a tire pressure monitoring 5. Once you repair or replace the original road tire and sensor. Therefore, the TPMS will not monitor the tire reinstall it on the vehicle in place of the compact spare tire, the TPMS will update automatically and the Tire pressure in the compact spare tire. Pressure Monitoring Telltale Light will turn OFF, as 2.
250 STARTING AND OPERATING The tire pressure sensors are covered under one of the Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at following licenses: high speeds can cause damage and immediate service is United States MRXC4W4MA4 required. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.
STARTING AND OPERATING 251 Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasoline contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasoline. Properly blended reformulated gasoline will provide excellent performance and durability of engine and fuel system components.
252 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles • Disconnect and reconnect the battery to reset the engine controller memory. Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged exposure to E-85 fuel. content may void the New Vehicle Limited Warranty.
STARTING AND OPERATING 253 Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
254 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 255 ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
256 STARTING AND OPERATING WARNING! (Continued) Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check fuel cap” message will be displayed in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center” in “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap until a “clicking” sound is heard.
STARTING AND OPERATING 257 VEHICLE LOADING • Vehicle Identification Number (VIN) As required by National Highway Traffic Safety Admin- • Type of Vehicle istration regulations, your vehicle has a certification label • Month Day and Hour of Manufacture (MDH) affixed to the driver’s side door or B-Pillar. The bar code allows a computer scanner to read the VIN. If seats are removed for carrying cargo, do not exceed the Gross Vehicle Weight Rating (GVWR) specified GVWR and GAWR.
258 STARTING AND OPERATING WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Inflation Pressure This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR.
STARTING AND OPERATING 259 The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the GVWR. have exceeded either GAWR, but the total load is within the specified GVWR, you must redistribute the weight. Improper weight distribution can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate.
260 STARTING AND OPERATING measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be The following trailer towing related definitions will assist supported by the scale. you in understanding the following information: Gross Axle Weight Rating (GAWR) Gross Vehicle Weight Rating (GVWR) Common Towing Definitions The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
STARTING AND OPERATING 261 Tongue Weight (TW) The tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% of the trailer load. You must consider this as part of the load on your vehicle. Weight-Carrying Hitch Trailer Sway Control A weight-distributing system works by applying leverage through spring (load) bars.
262 STARTING AND OPERATING Trailer sway control and a weight distributing (load tow and should be used to assist you in selecting the equalizing) hitch are recommended for heavier Tongue correct trailer hitch for your intended towing condition. Weights (TW) and may be required depending on vehicle Trailer Hitch Classification Definitions and trailer configuration/loading to comply with Gross Axle Weight Rating (GAWR) requirements. Class Max.
STARTING AND OPERATING 263 Trailer Towing Weights (Maximum Trailer Weight Ratings) which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. NOTE: For additional trailer towing information (maximum trailer weight ratings) refer to the following website Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. addresses: • ramtrucks.com/en/towing_guide/ • ramtruck.ca (Canada) • rambodybuilder.
264 STARTING AND OPERATING Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your new vehicle drive• The tongue weight of the trailer. train components, the following guidelines are recom• The weight of any other type of cargo or equipment mended. put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING 265 Perform the maintenance listed in the “Maintenance Schedule.” Refer to “Maintenance Schedule” for the proper maintenance intervals. When towing a trailer, never exceed the GAWR or GCWR ratings. WARNING! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel.
266 STARTING AND OPERATING WARNING! (Continued) • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized. Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 267 Towing Requirements — Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
268 STARTING AND OPERATING CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety.
STARTING AND OPERATING 269 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
270 STARTING AND OPERATING Towing Tips Tow/Haul Mode Before setting out on a trip, practice turning, stopping, To reduce the potential for automatic transmission overand backing up the trailer in an area located away from heating, activate the “TOW/HAUL” feature when drivheavy traffic. ing in hilly areas, or select a lower gear range (using the Electronic Range Select (ERS) shift control) on more Automatic Transmission severe grades. The DRIVE gear can be selected when towing.
STARTING AND OPERATING 271 Highway Driving Cooling System To reduce potential for engine and transmission over- Reduce speed. heating, take the following actions: Air Conditioning City Driving Turn off temporarily. When stopped for short periods, shift the transmission into NEUTRAL and increase engine idle speed. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
272 STARTING AND OPERATING Recreational Towing — Automatic Transmission Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer’s instructions. 2. Drive the front wheels onto the tow dolly. 3. Firmly apply the parking brake. Place the transmission in PARK. 4.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .275 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .288 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .275 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . .289 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .276 ▫ Removing The Spare Tire . . . . . . . . . . . . . . . .290 ▫ Torque Specifications . . . . . . . . . . . . . . . . . . .276 䡵 TIREFIT KIT — IF EQUIPPED . . . . . .
274 WHAT TO DO IN EMERGENCIES 䡵 FREEING A STUCK VEHICLE . . . . . . . . . . . . .307 䡵 TOWING A DISABLED VEHICLE . . . . . . . . . . .309 䡵 SHIFT LEVER OVERRIDE . . . . . . . . . . . . . . . .308 ▫ Automatic Transmission . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 275 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the climate controls. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning • On the highways — slow down. flasher.
276 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately and call for service.
WHAT TO DO IN EMERGENCIES 277 Inspect the wheel mounting surface prior to mounting Tighten the lug nuts/bolts in a star pattern until each the tire and remove any corrosion or loose particles. nut/bolt has been tightened twice.
278 WHAT TO DO IN EMERGENCIES After 25 miles (40 km) check the lug nut/bolt torque to be TIREFIT KIT — IF EQUIPPED sure that all the lug nuts/bolts are properly seated Small punctures up to ¼” (6 mm) in the tire tread can be against the wheel. sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can WARNING! be used in outside temperatures down to approximately To avoid the risk of forcing the vehicle off the jack, -4°F (-20°C).
WHAT TO DO IN EMERGENCIES 279 TIREFIT Kit Components And Operation Using The Mode Select Knob And Hoses Your TIREFIT kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only. Use the Black Air Pump Hose (7) when selecting this mode.
280 WHAT TO DO IN EMERGENCIES Using The Power Button Push and release the Power Button (4) once to turn On the TIREFIT kit. Push and release the Power Button (4) again to turn Off the TIREFIT kit. Using The Deflation Button Press the Deflation Button (2) to reduce the air pressure in the tire if it becomes over-inflated.
WHAT TO DO IN EMERGENCIES 281 the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the TIREFIT kit. • You can use the TIREFIT air pump to inflate bicycle tires. The kit also comes with two needles, located in the Accessory Storage Compartment (on the bottom of the air pump) for inflating sport balls, rafts, or similar inflatable items.
282 WHAT TO DO IN EMERGENCIES WARNING! (Continued) WARNING! (Continued) • Keep TIREFIT away from open flames or heat source. • A loose TIREFIT kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the TIREFIT kit in the place provided. Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you.
WHAT TO DO IN EMERGENCIES 283 the sealant into the deflated tire and running the air 5. Uncoil the Power Plug (8) and insert the plug into the vehicle’s 12 Volt power outlet. pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. NOTE: Do not remove foreign objects (e.g., screws or 3. Place the transmission in PARK (auto transmission) or in nails) from the tire. Gear (manual transmission) and turn Off the ignition.
284 WHAT TO DO IN EMERGENCIES If the sealant (white fluid) does not flow within 0 – 10 If the sealant (white fluid) does flow through the seconds through the Sealant Hose (6): Sealant Hose (6): 1. Press the Power Button (4) to turn Off the TIREFIT kit. 1. Continue to operate the pump until sealant is no Disconnect the Sealant Hose (6) from the valve stem. longer flowing through hose (typically takes 30 - 70 Make sure the valve stem is free of debris. Reconnect seconds).
WHAT TO DO IN EMERGENCIES 285 3. Immediately disconnect the Sealant Hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the TIREFIT kit in the vehicle storage • The tire is too badly damaged. Do not attempt to drive location. Quickly proceed to (D) “Drive Vehicle.” the vehicle further. Call for assistance. If the tire does not inflate to at least 26 psi (1.
286 WHAT TO DO IN EMERGENCIES (D) Drive Vehicle: (E) After Driving: Immediately after injecting sealant and inflating the tire, Pull over to a safe location. Refer to “Whenever You Stop drive the vehicle 5 miles (8 km) or 10 minutes to ensure to Use TIREFIT” before continuing. distribution of the TIREFIT Sealant within the tire. Do not 1. Push in the Mode Select Knob (5) and turn to the Air exceed 55 mph (90 km/h). Mode position. WARNING! TIREFIT is not a permanent flat tire repair.
WHAT TO DO IN EMERGENCIES 287 5. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized dealer as soon as pos1. Press the Power Button (4) to turn on TIREFIT and sible. Refer to (F) “Sealant Bottle and Hose Replaceinflate the tire to the pressure indicated on the tire and ment”. loading information label on the driver-side door opening.
288 WHAT TO DO IN EMERGENCIES 4. Clean any remaining sealant from the TIREFIT hous- JACKING AND TIRE CHANGING ing. 5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6.
WHAT TO DO IN EMERGENCIES 289 WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack and jack tools are stored under the front passenger seat.
290 WHAT TO DO IN EMERGENCIES Removing The Spare Tire 1. Remove the spare tire before attempting to jack up the vehicle. Attach the lug bolt adapter to the winch extension and insert it into the winch mechanism. Winch Location The winch mechanism is located under the rear of the vehicle to the right of the spare tire.
WHAT TO DO IN EMERGENCIES 291 NOTE: The winch mechanism is designed for use with the winch extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. 6 Winch Extension 2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
292 WHAT TO DO IN EMERGENCIES 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 4. Remove the retainer nut prior to removing the retainer from the wheel.
WHAT TO DO IN EMERGENCIES 293 5. Lift the spare tire with one hand to give clearance to 6. Pull the retainer through the center of the wheel. tilt the retainer at the end of the cable.
294 WHAT TO DO IN EMERGENCIES 6. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Block the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2.
WHAT TO DO IN EMERGENCIES 295 WARNING! (Continued) WARNING! (Continued) • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack.
296 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Loosen (but do not remove) the wheel lug bolts by turning them to the left one turn while the wheel is still on the ground. 2. There are two jack engagement locations on each side of the vehicle body.
WHAT TO DO IN EMERGENCIES 297 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated. NOTE: The rear jacking location is located in front of the rear tire and in front of the leaf spring mount.
298 WHAT TO DO IN EMERGENCIES NOTE: The front jacking location is located behind the front tire and in front of the driver’s door. WARNING! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. 3.
WHAT TO DO IN EMERGENCIES 299 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel lug bolts. For vehicles with wheel covers, remove the cover from the wheel by hand. Do not pry the wheel cover off. Then pull the wheel off the hub. 6. Install the spare tire. Lightly tighten the wheel lug bolts.
300 WHAT TO DO IN EMERGENCIES WARNING! WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately.
WHAT TO DO IN EMERGENCIES 301 Wheel Covers CAUTION! Use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. The wheel covers on the vehicle are held in place by the wheel lug bolts and can be removed after the wheel lug bolts are taken off.
302 WHAT TO DO IN EMERGENCIES Preparations For Jump-Start The vehicle’s jump starting remote posts are located under the hood, in the engine compartment on the driver’s side. The Remote Positive (+) Post is covered with a protective cap located on the side of the Front Power Distribution Center. The Remote Negative (-) Post is located on the core support closest to the front of the vehicle.
WHAT TO DO IN EMERGENCIES 303 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
304 WHAT TO DO IN EMERGENCIES CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting The Jumper Cables 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. NOTE: The remote positive (+) post is located in the engine compartment on the driver’s side under the cover of the Front Power Distribution Center. 2.
WHAT TO DO IN EMERGENCIES 305 6. Once the engine is started, disconnect the jumper If frequent jump-starting is required to start your vehicle cables in the reverse sequence: you should have the battery and charging system inspected at your authorized dealer. Disconnecting The Jumper Cables 1. Disconnect the negative end (-) of the jumper cable from the remote negative (-) post of the vehicle with the discharged battery. 2.
306 WHAT TO DO IN EMERGENCIES Battery Location There are two remote jump starting posts under the hood which is the recommended jump start location. If access to the battery is needed, an access panel on the driver’s side floor will allow for battery access.
WHAT TO DO IN EMERGENCIES 307 FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between DRIVE and REVERSE , while gently pressing the accelerator. Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.
308 WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. And do not let anyone near a spinning wheel, no matter what the speed. 3.
WHAT TO DO IN EMERGENCIES 309 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service.
310 WHAT TO DO IN EMERGENCIES If you must use the accessories (wipers, defrosters, etc.) Automatic Transmission while being towed, the ignition must be in the ON/RUN The manufacturer recommends towing your vehicle with position. all four wheels OFF the ground using a flatbed.
WHAT TO DO IN EMERGENCIES 311 CAUTION! • Towing faster than 25 mph (40 km/h) or farther than 15 mi (24 km) with front wheels on the ground can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .315 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .324 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .316 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . .324 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .317 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .327 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . .317 ▫ Air Conditioner Maintenance . . . . . . . . . . . .
314 MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .343 ▫ Daytime Running Lamp (DRL)/ Front Side Marker Lamp . . . . . . . . . . . . . . . .362 ▫ Cleaning The Instrument Panel Cupholders . .349 ▫ Front Fog Lamps . . . . . . . . . . . . . . . . . . . . . .363 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349 ▫ Front, Rear Roof Lamps . . . . . . . . . . . . . . . . .364 ▫ Underhood Fuses. . . . . . . . .
MAINTAINING YOUR VEHICLE 315 ENGINE COMPARTMENT — 3.
316 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 317 Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE If the vehicle diagnostic system determines that the fuel PROGRAMS filler cap is loose, improperly installed, or damaged, a In some localities, it may be a legal requirement to pass “Check fuel cap” message will be displayed in the an inspection of your vehicle’s emissions control system. Electronic Vehicle Information Center (EVIC). Refer to Failure to pass could prevent vehicle registration.
318 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition actuated test, which you • The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the can use prior to going to the test station. To check if your engine. This means that your vehicle’s OBD II system vehicle’s OBD II system is ready, you must do the following: is ready and you can proceed to the I/M station. 1. Cycle the ignition switch to the ON position, but do not crank or start the engine.
MAINTAINING YOUR VEHICLE 319 NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil Use of genuine MOPAR® parts for normal/scheduled penalties being assessed against you. maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures WARNING! caused by the use of non-MOPAR® parts for maintenance and repairs will not be covered by the New Vehicle You can be badly injured working on or around a Limited Warranty.
320 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed “Maintenance Schedule”, there are other components which may require servicing or replacement in the future.
MAINTAINING YOUR VEHICLE 321 Change Engine Oil Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. To assure proper engine lubrication, the engine oil must Refer to the “Maintenance Schedule” for further informabe maintained at the correct level. Check the oil level at tion. regular intervals, such as every fuel stop.
322 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol Engine Oil Viscosity — 3.6L Engine MOPAR® SAE 5W-20 engine oil approved to Chrysler Material Standard MS-6395 such as Pennzoil®, Shell This symbol means that the oil has Helix® or equivalent is recommended for all operating been certified by the American temperatures. This engine oil improves low temperature Petroleum Institute (API). The starting and vehicle fuel economy.
MAINTAINING YOUR VEHICLE 323 station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in You may use synthetic engine oils provided the recomyour area. mended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes Engine Oil Filter are followed. The engine oil filter should be replaced with a new filter Materials Added To Engine Oil at every engine oil change.
324 MAINTAINING YOUR VEHICLE used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recomRefer to the “Maintenance Schedule” for the proper mended. maintenance intervals. Exhaust System Engine Air Cleaner Filter WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE 325 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
326 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE 327 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
328 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE 329 WARNING! (Continued) Refrigerant Recovery And Recycling • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
330 MAINTAINING YOUR VEHICLE The A/C air filter is located in the fresh air inlet in the 2. Remove and replace the A/C air filter from the filter engine compartment. Perform the following procedure to retainer. replace the filter: 1. Remove the two screws that secure the filter retainer to the fresh air inlet, and remove the filter retainer.
MAINTAINING YOUR VEHICLE 331 3. Install the A/C air filter/filter retainer back into the other underhood services, the hood latch, release mechafresh air inlet. When installing the filter retainer make nism and safety catch should be cleaned and lubricated. sure the retainer is fully engaged. The external lock cylinders should be lubricated twice a 4. Install the two screws back into the assembly to secure year, preferably in the Fall and Spring.
332 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use.
MAINTAINING YOUR VEHICLE 333 Coolant Checks Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
334 MAINTAINING YOUR VEHICLE If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (antifreeze) (conforming to MS12106). Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 335 CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
336 MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deion- • Mixing engine coolant (antifreeze) types is not recomized water when mixing the water/engine coolant mended and can result in cooling system damage. If HOAT and OAT coolant are mixed in an emergency, (antifreeze) solution.
MAINTAINING YOUR VEHICLE 337 WARNING! • Do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.
338 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE 339 Brake System Master Cylinder — Brake Fluid Level Check In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The fluid level in the master cylinder should be checked when performing underhood services, or immediately if the “Brake System Warning Light” indicates system failure.
340 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. WARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.
MAINTAINING YOUR VEHICLE 341 WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Automatic Transmission (3.
342 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately.
MAINTAINING YOUR VEHICLE 343 Appearance Care And Protection From Corrosion What Causes Corrosion? Protection Of Body And Paint From Corrosion Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.
344 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once a month. • Use a high quality cleaner wax, such as MOPAR® Cleaner Wax to remove road film, stains and to protect • It is important that the drain holes in the lower edges your paint finish.
MAINTAINING YOUR VEHICLE 345 • If you carry special cargo such as chemicals, fertilizers, • For aluminum wheels, use MOPAR® Wheel Cleaner (Part# 04796239AB) or equivalent. de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use MOPAR® Touch Up Paint on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.
346 MAINTAINING YOUR VEHICLE • Blot any remaining stain with a clean, damp towel. Cleaning Interior Trim • For tough stains, apply MOPAR® Total Clean, or a Interior trim should be cleaned starting with a damp mild soap solution to a clean, damp cloth and remove cloth, a damp cloth with MOPAR® Total Clean or equivastain. Use a fresh, damp towel to remove soap residue. lent, then MOPAR® Spot & Stain Remover or equivalent if absolutely necessary.
MAINTAINING YOUR VEHICLE 347 liquid. Please do not use polishes, oils, cleaning fluids, Plastic is not as scratch resistant as glass and therefore solvents, detergents, or ammonia-based cleaners to clean different lens cleaning procedures must be followed. your leather upholstery. Application of a leather condiTo minimize the possibility of scratching the lenses and tioner is not required to maintain the original condition. reducing light output, avoid wiping with a dry cloth.
348 MAINTAINING YOUR VEHICLE When cleaning the rear view mirror, spray cleaner on the If the belts need cleaning, use MOPAR® Total Clean, a towel or rag that you are using. Do not spray cleaner mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Dry with a soft directly on the mirror. cloth.
MAINTAINING YOUR VEHICLE 349 Cleaning The Instrument Panel Cupholders Installation Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the Pull the flexible liner from the cupholder drawer starting corresponding openings in the drawer. at one edge to ease removal. FUSES Cleaning Removal The liner is top shelf dishwasher safe, or you may follow the cleaning procedure below.
350 MAINTAINING YOUR VEHICLE WARNING! (Continued) • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • If the replaced fuse blows again, contact an authorized dealer. • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer.
MAINTAINING YOUR VEHICLE 351 Cavity F01 F02 F02 Maxi Fuse 40 Amp Orange 20 Amp Yellow (3.6 Gasoline Engine) 50 Amp Red (3.0 Diesel Engine) Mini Fuse Description ESC Pump Cavity F04 Starter Relay 3.6L (3.6 Gasoline Engine) F04 Glow Plug Unit (3.0 Diesel Engine) F05 Maxi Fuse 50 Amp Red (3.6 Gasoline Engine) 40 Amp Orange (3.0 Diesel Engine) 30 Amp Green Mini Fuse Description Secondary PDC (Trans Power Relay, Vacuum Pump, KL30 for STM) (3.6 Gasoline Engine) Fuel Filter Heater (3.
352 MAINTAINING YOUR VEHICLE Cavity F06 F07 F08 Maxi Fuse 40 Amp Orange (non A/C) 60 Amp Blue (A/C) 50 Amp Red (non A/C) 60 Amp Blue (A/C) 40 Amp Orange Mini Fuse Description Engine Cooling Fan - 2nd Speed Cavity F09 F10 F11 Engine Cooling Fan - 1st Speed F14 F15 F16 Passenger Compartment Blower Maxi Fuse Mini Fuse Description 15 Amp Blue 15 Amp Blue 15 Amp Blue Rear Power Outlet 20 Amp Yellow 7.5 Amp Brown 7.5 Amp Brown Horn MPROP-DRV (3.
MAINTAINING YOUR VEHICLE 353 Cavity Maxi Fuse Mini Fuse Description Cavity F16 7.5 Amp Brown F17 20 Amp Yellow 20 Amp Yellow KL15 MTA, KL15 Shift Lever Unit, KL15 ECM, KL15 Starter Relay Coil (3.0 Diesel Engine) ECM, Injectors (3.6 Gasoline Engine) Secondary Loads, ECM (3.0 Diesel Engine) KL30 ECM, KL30 Main Relay Coil (3.6 Gasoline Engine) F17 F18 7.5 Amp Brown Maxi Fuse Mini Fuse Description F18 7.5 Amp Brown F19 7.
354 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Mini Fuse F22 20 Amp Yellow F23 20 Amp Yellow 7.5 Amp Brown F24 F30 15 Amp Blue Description ECM, Primary Loads (3.0 Diesel Engine) ESC Valves Front PDC Additional Fuses The additional fuse box is located inside the front PDC Box. KL15 Vacuum pump relay coil (3.
MAINTAINING YOUR VEHICLE 355 Cavity F61 Mini Fuse 20 Amp Yellow F62 30 Amp Green F64 7.5 Amp Brown 25 Amp White F65 F66 5 Amp Beige Description Vacuum Pump (3.6 Gasoline Engine) — If Equipped Transmission Power RELE (3.6 Gasoline Engine) — If Equipped Urea Pump (3.0 Diesel Engine) — If Equipped Urea NOX Sensor 1–2 — PM Sensor (3.0 Diesel Engine) — If Equipped STM (3.
356 MAINTAINING YOUR VEHICLE Cavity F31 F32 F34 F36 Fuse Panel Cavity Locations Cavity F12 F13 Mini Fuse 10 Amp Red 10 Amp Red Description Right Low Beam Left Low Beam F37 F38 F42 F43 Mini Fuse 5 Amp Beige 10 Amp Red 7.
MAINTAINING YOUR VEHICLE 357 Cavity F47 F48 F49 F50 F51 F53 F90 F91 Mini Fuse 20 Amp Yellow 20 Amp Yellow 5 Amp Beige 7.5 Amp Brown 5 Amp Beige 5 Amp Beige 7.5 Amp Brown 7.5 Amp Brown Description Driver Power Window Passenger Power Window INT (PAM – CCS – RRM – ECM) INT (ORC) INT (REAR CAMERAAUX) +30 (IPC) Left High Beam Right High Beam Cavity F92 F93 Mini Fuse 7.5 Amp Brown 7.
358 MAINTAINING YOUR VEHICLE Right Central Pillar Fuses The right central pillar fuse panel is located on the interior side at the base of the passenger side B pillar. Fuse Panel Cavity F81 Fuse Panel Location F83 Mini Fuse 7.
MAINTAINING YOUR VEHICLE 359 Cavity F84 F85 Mini Fuse 20 Amp Yellow 10 Amp Red Description Rear Right Windows Heater Rear Heater Prep VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. REPLACEMENT BULBS Interior Bulbs Overhead Lamp Sun Visors Courtesy Lamp Glove Compartment Rear Courtesy Lamp Bulb Number C5W C5W FF500 C5W C5W • Disconnect the negative cable from the battery.
360 MAINTAINING YOUR VEHICLE Exterior Bulbs Front Low and High Beam Headlamp Front Park/Turn Signal Lamps Daytime Running Lamps (if equipped) Front Side Marker Lamps Rear Tail/Stop Lamps Rear Turn Signal Lamps Rear Backup Lamps Rear Side Marker Lamps Front Fog Lamps Bulb Number H7LL 7444NA 7440 WY5W 7443 7440NA 921 W3W H11 License Plate Lamps Front Roof Lamps Rear Roof Lamps Bulb Number C5W WY5W W3W NOTE: • Numbers refer to commercial bulb types that can be purchased from your authorized dealer.
MAINTAINING YOUR VEHICLE 361 Headlamps Low beam and High beam 10. Install new bulb. NOTE: Passenger side headlamp must be removed for 11. Push socket back into reflector until it locks back into bulb replacement, for driver side headlamp go to step 6 place. through step 12. 12. Install access cap. 1. Remove screw (1) on lower headlamp filler panel. 13. Carefully re install headlamp in the same position on 2. Remove screws (2) on upper headlamp filler panel.
362 MAINTAINING YOUR VEHICLE Front Turn Signal/Parking Lamps 9. Install upper screw (1) on headlamp housing. NOTE: Passenger side headlamp must be removed for 10. Install lower screws (2) on headlamp housing. bulb replacement, for driver side headlamp go to step 6 11. Carefully re install screw (1) on lower headlamp filler through step 7. panel. 1. Remove screw (1) on lower headlamp filler panel. 12. Carefully re install screws (2) on upper headlamp 2. Remove screws (2) on upper headlamp filler panel.
MAINTAINING YOUR VEHICLE 363 5. Pull Headlamp forward. Front Fog Lamps 6. Remove the DRL, side marker bulb by pulling straight 1. Turn front wheels inboard to access cover in wheel liner. out. 7. Replace lamp as required and lock in place. 2. Open the cover on the front of the wheel liner. 8. Reinstall plastic cap. 3. Remove connection and replace the bulb. 9. Carefully re install headlamp in the same position on 4. Connect the wire and rotate bulb/socket clockwise into lamp locking it in place.
364 MAINTAINING YOUR VEHICLE Front, Rear Roof Lamps 1. Remove two screw and remove the lamp assembly. 2. Remove the socket bulb by turning counterclockwise. 3. Remove bulb and replace as needed. 4. Reinstall the bulb socket and rotate clockwise to lock in place. 5. Reinstall lamp. Rear Tail, Stop, Backup, Turn Signal And Rear Side Marker Lamps 1. Open rear doors. 2. Remove the two screws and remove the tail lamp. 3.
MAINTAINING YOUR VEHICLE 365 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.6L Engine (SAE 5W-20, API Certified) Cooling System * 3.6L Engine (MOPAR® Antifreeze/ Engine Coolant 10 Year/150,000 Mile Formula or equivalent) U.S. 24 Gallons Metric 90 Liters 6 Quarts 5.6 Liters 10.
366 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-12106.
MAINTAINING YOUR VEHICLE 367 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
368 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission – 3.6L Gasoline Engine Only Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part Use Only ATF+4® Automatic Transmission Fluid. Failure to use ATF+4® fluid may affect the function or performance of your transmission. We recommend MOPAR® ATF+4® Fluid. We recommend you use MOPAR® DOT 4. Use Pentosin CHF 11S power steering fluid meeting Chrysler Material Standard MS-11655.
M A I N T E N A ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .372 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 370 MAINTENANCE SCHEDULES than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)” in “Understanding Your indicator system. The oil change indicator system will Instrument Panel” for further information. remind you that it is time to take your vehicle in for scheduled maintenance.
MAINTENANCE SCHEDULES 371 M • Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering and fill as needed • Check function of all interior and exterior lights Required Maintenance Intervals Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires.
M A I N T E N A N C E 372 MAINTENANCE SCHEDULES S C H E D U L E S Or Years: Or Kilometers: 8 Maintenance Chart Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the brake pads, replace as necessary.
Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace Brake Fluid every two years Replace spark plugs (3.6L engine). ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 2 3 4 5 6 7 8 9 10 11 12 13 14 15 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 M 374 MAINTENANCE SCHEDULES A I Mileage or time passed N (whichever comes first) T E N Or Years: A Or Kilometers: N C E S Change automatic transmission X C fluid and filter. H Inspect and replace PCV valve if E necessary.
MAINTENANCE SCHEDULES 375 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . .379 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .381 ▫ Prepare For The Appointment. . . . . . . . . . . . .379 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .381 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .379 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .382 ▫ Be Reasonable With Requests . .
378 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . .385 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .385 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .385 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 379 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you are having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
380 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer. Phone: (866) 726–4636 They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE 381 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY. Warranty expires.
382 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 383 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
384 IF YOU NEED CONSUMER ASSISTANCE Service Manuals Owner’s Manuals These comprehensive Service Manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing Chrysler Group LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts.
IF YOU NEED CONSUMER ASSISTANCE 385 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. The following tire grading categories were established by the National Highway Traffic Safety Administration.
386 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
388 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .335 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .332 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .253 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .48 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 389 Special Additives . . . . . . . . . . . . . . . . . . . . . . .341 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .327 Keyless Transmitter Replacement (RKE) . . . . . . . .20 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Body Builders Guide . . . . . . . . . . . . . . . . . . . . . . . .6 Body Mechanism Lubrication . . . . . . . . . . . . . . . . .
390 INDEX Clean Air Gasoline . . . . . . . . . . . . . Cold Weather Operation . . . . . . . . . Compact Disc (CD) Maintenance . . . Compact Spare Tire . . . . . . . . . . . . . Console, Overhead . . . . . . . . . . . . . Contract, Service . . . . . . . . . . . . . . . Coolant Pressure Cap (Radiator Cap) Cooling System. . . . . . . . . . . . . . . . Adding Coolant (Antifreeze) . . . . Coolant Capacity . . . . . . . . . . . . Coolant Level . . . . . . . . . . . . . . . Disposal of Used Coolant . . . . . .
INDEX 391 Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 Electric Remote Mirrors. . . . . . . . . . . . . . . . . . . . . .73 Electronic Brake Control System . . . . . . . . . . . . . . .209 Brake Assist System . . . . . . . . . . . . . . . . . . . . .211 Electronic Speed Control (Cruise Control) . . . . . . . . .98 Electronic Stability Control (ESC) . . . . . . . . . . . . . .
392 INDEX Flooded Engine Starting . . . . . . . . . . . . . . . . . . . .187 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . .365 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . . .342 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . .333 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 393 Gauge . . . . . . . Light . . . . . . . . Materials Added Methanol . . . . . Octane Rating . . Requirements . . Tank Capacity . . Fueling . . . . . . . . Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 Gear Select Lever Override . . . . . . . . . . . . . . . . . .308 General Information . . . . . . . . . . . . . . . . . . . . . . .249 General Maintenance. . . . . . . . .
394 INDEX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Heated Mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . . .188 High Beam/Low Beam Select (Dimmer) Switch . . . . .
INDEX 395 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 High Beam Indicator . . . . . . . . . . . . . . . . . . . . .124 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .239 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .18 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .124 Lights . .
396 INDEX Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 Locks Automatic Door . . . . . . . . . . . . . . . . . . . . . . . . .23 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . .14 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .331 Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276 Maintenance Free Battery. . . . . . . . . . . . . . . . . . . .
INDEX 397 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .365 Change Interval . . . . . . . . . . . . . . . . . . . . . . . .321 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . .323 Identification Logo . . . . . . . . . . . . . . . . . . . . . .
398 INDEX Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . .72 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . .51 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . .271 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . .251 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329 Reminder, Seat Belt. . . . . . . . . . . . . . . . . . . . . . . . .36 Remote Keyless Entry (RKE) FCC General Information . . . . . . . . . . . . . .
INDEX 399 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Selection of Coolant (Antifreeze). . . . . . . . . . . . . . .366 SENTRY KEY® FCC General Information . . . . . . . . . . . . . . . . . .16 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . .
400 INDEX Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . .323 Tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Telescoping Steering Column . . . . . . . . . . . . . . . . . .97 Tire and Loading Information Placard . . . . . . . . . . .225 TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .218 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 401 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . .210 Traction Control Switch . . . . . . . . . . . . . . . . . . . . .210 Trailer Sway Control (TSC) . . . . . . . . . . . . . . . . . .215 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . .259 Cooling System Tips . . . . . . . . . . . . . . . . . . . . .271 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 Minimum Requirements . . . . . . . . . . . . . . . . . .264 Tips . . . . . . . . . . .
402 INDEX Washer Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .332 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .343 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .202 Wind Buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2014 ProMaster 2014 OWNER’S MANUAL Chrysler Group LLC 14VF-126-AD Fourth Edition Rev 2 Printed in U.S.A.
