uconnect 8.4A/8.4AN ® 14UC84A-526-AC Third Edition Rev 1 Uconnect® 8.4A/8.
SECTION TABLE OF CONTENTS PAGE 1 IDENTIFYING YOUR RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 ALL ABOUT UCONNECT® ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UCONNECT® 8.4A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 3 4 UCONNECT® 8.4AN . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDENTIFYING YOUR RADIO CONTENTS 䡵 Identifying Your Radio . . . . . . . . . . . . . . . . . . . . .4 ▫ Key Features . . . . . . . . . . . . . . . . . . . . . . . . . .
4 IDENTIFYING YOUR RADIO Identifying Your Radio Key Features Uconnect® 8.4A/8.4AN The 8.4A and 8.4AN share some features between them, but the 8.4AN has some features that sets it apart. The below features are shared between them: • 8.4” Touchscreen • Hands-free/Bluetooth® • USB port, AUX port and SD Card slot — If Equipped • Touchscreen Climate Controls • SiriusXM Satellite Radio with 1yr Trial Included — If Equipped • Uconnect® Access — U.S.
IDENTIFYING YOUR RADIO 5 The 8.4AN sets itself apart by offering these unique • SiriusXM Traffic with 1yr Trial Included — U.S. Marfeatures: ket Only — If Equipped • HD Radio — U.S. Market Only • Navigation Standard • SiriusXM Travel Link with 1yr Trial Included — U.S. Market Only — If Equipped NOTE: 3D Landmarks are visible at 250ft and below, 3D City Models are visible at 50ft and below and Digital • 3D content (Select this option and zoom to an appro- Terrain is visible at 100mi and below.
ALL ABOUT Uconnect® ACCESS 2 CONTENTS 䡵 Introduction To Uconnect® Access . . . . . . . . . . . .9 ▫ Using Mopar Owner Connect . . . . . . . . . . . . . .42 ▫ What Is Uconnect® Access? . . . . . . . . . . . . . . . .9 䡵 Using Uconnect® Access. . . . . . . . . . . . . . . . . . .46 ▫ Included Trial Period For New Vehicles . . . . . . .13 ▫ Getting Started With Apps . . . . . . . . . . . . . . . .46 ▫ Features And Packages . . . . . . . . . . . . . . . . . .14 ▫ 9-1-1 Call . . . . . . . . . . . . . . . .
8 ALL ABOUT Uconnect® ACCESS ▫ SRT Performance Pages/SRT Performance Pages Plus . . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ How To Remove My Uconnect® Access Account . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 ▫ Voice Texting . . . . . . . . . . . . . . . . . . . . . . . . .92 ▫ Adding Vehicles To My Uconnect® Access Account . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 ▫ Remote Door Lock/Unlock. . . . . . . . . . . . . . .102 ▫ Remote Vehicle Start . . . . . .
ALL ABOUT Uconnect® ACCESS 9 Introduction To Uconnect® Access Uconnect® Access provides: To unlock the full potential of Uconnect® Access in your • The ability to remotely lock/unlock your doors and vehicle, you first need to register with Uconnect® Access. start your vehicle (if equipped) from virtually anywhere, with the Uconnect® Access App, the Mopar What Is Uconnect® Access? Owner Connect website (moparownerconnect.com) Uconnect® Access enhances your ownership and driving and Uconnect® Care.
10 ALL ABOUT Uconnect® ACCESS Before you drive, familiarize yourself with the easy-touse Uconnect® System. This is where you can begin registration for Uconnect® Access, find the apps and purchase WiFi Hotspot on demand. 1. The ASSIST And 9-1-1 Buttons On Your Rearview 3. The Uconnect® Voice Command And Uconnect® Mirror Phone Buttons On Your Steering Wheel The ASSIST Button is used for contacting Roadside Assistance, Vehicle Care and Uconnect® Care.
ALL ABOUT Uconnect® ACCESS 11 WARNING! ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume all risks related to the use of the Uconnect® features and applications in this vehicle. Only use Uconnect® when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.
12 ALL ABOUT Uconnect® ACCESS 1 — Steering Wheel Audio Controls (Left Rear Surface of Steering Wheel) 2 — Uconnect® Voice Command Button 3 — Uconnect® Phone Button 4 — Assist Button 5 — 9-1-1 Button 6 — Uconnect® Access 8.
ALL ABOUT Uconnect® ACCESS 13 first register with Uconnect® Access. Once registered, Your new vehicle may come with an included trial period Uconnect® Access customers can purchase additional for use of the Uconnect® Access Services starting at the services and Apps over the lifetime of their vehicle ownership. date of vehicle purchase*. To activate the trial, you must Included Trial Period For New Vehicles Radio Radio Sales Code Trial Period Included Trial on New Vehicles ONLY Uconnect® 8.
14 ALL ABOUT Uconnect® ACCESS • Only the Uconnect® 8.4AN will have the HD Radio icon when listening to FM or AM stations. The icon will be lit when it is receiving an HD Radio signal (not all stations currently broadcast an HD Radio signal). Features And Packages After the trial period, you can subscribe to continue your service by visiting the Uconnect® Store located within the Mopar Owner Connect website (moparownerconnect.com). If you need assistance, you can also call Uconnect® Care at 855-792-4241.
ALL ABOUT Uconnect® ACCESS 15 NOTE: Should you require assistance anytime during the 2. Press “Register” on the reminder screen or select the registration process, call Uconnect® Care at 1-855-792-4241. “Uconnect® Registration” button on the touchscreen which appears in the “Favorites Tab” on the Apps list.
16 ALL ABOUT Uconnect® ACCESS 3. The Uconnect® Access Registration App will open and display step-by-step instructions to start your registration. 1 — Press To Enter Email Address 2 — Press To Re-enter Email Address 4. Enter your email address into the radio touchscreen.
ALL ABOUT Uconnect® ACCESS 17 5. This message will display on the touchscreen indicat- 6. A final message will display on the touchscreen allowing your email submission was accepted. In a few ing you to check on the status of your email submisminutes, you will receive an email which will allow sion. To exit the registration, press the “X” in the upper you to register your vehicle for Uconnect® Access. You right corner. should open this email and begin your Uconnect® Access registration within 72 hours.
18 ALL ABOUT Uconnect® ACCESS 7. Check for an email from Uconnect® Access that contains your personalized registration link. If you don’t see it, check your spam or junk mail folder. Open the email and click on the link to continue registering. NOTE: For security reasons, this link is valid for 72 hours from the time you submitted your email address into the radio touchscreen.
ALL ABOUT Uconnect® ACCESS 19 2
20 ALL ABOUT Uconnect® ACCESS For additional registration assistance while in the vehicle, turn the ignition on and push the ASSIST button to contact Uconnect® Care. 8. To unlock the full potential of Uconnect® Access in your vehicle, you will need to create or validate an existing Mopar Owner Connect account (previously Owner Center).
ALL ABOUT Uconnect® ACCESS 21 2
22 ALL ABOUT Uconnect® ACCESS 9. Once you are logged in to your Mopar Owner Connect account, you will create a personal Uconnect® Security PIN. The Uconnect® Security PIN will be required to authenticate you when accessing your account via Uconnect® Care or performing any remote services such as Remote Door Lock/Unlock, Remote Horn & Lights, or Remote Vehicle Start (If Equipped). 10. Review And Accept Your Trial Package And The Uconnect® Access Terms Of Service.
ALL ABOUT Uconnect® ACCESS 23 At this point your vehicle is registered with Uconnect® Access. Apps will be downloaded the next time you start your vehicle. If the Apps have not appeared after 24 hours, please contact Uconnect® Care. The recommended next steps are to: • Download the Uconnect® Access App (allows you to utilize services such as Remote Door Unlock and Via Mobile). • Set up your Uconnect® Payment Account (provides the option to purchase WiFi Hotspot and renew your subscription).
24 ALL ABOUT Uconnect® ACCESS Unlike your key fob, the Uconnect® Access app on your smartphone can send commands to your vehicle from Description any distance so long as your phone and vehicle are both The Uconnect® Access smartphone app allows you to in cellular range. The Uconnect® Security PIN that was remotely lock or unlock your doors, start your engine (if set up during registration is required for remote services. equipped) and activate your horn and lights from virtually anywhere.
ALL ABOUT Uconnect® ACCESS 25 2
26 ALL ABOUT Uconnect® ACCESS Get the Uconnect® Access smartphone app: 1. From your smartphone, go to your respective app store and search for “Uconnect Access”. 2. Download the app (there is no charge to download and install the app to your smartphone).
ALL ABOUT Uconnect® ACCESS 27 Using Via Mobile: Launch the Uconnect® Access app on your connected smartphone and log in with your Mopar Owner Connect Username/Email and password. From the vehicle touchscreen select a Via Mobile app from the apps list. To launch an app using voice recognition, push the “VR” button on the steering wheel and say, “launch [app name] via mobile.” The Via Mobile button provides a status indication of the smartphone connection for Via Mobile app use.
28 ALL ABOUT Uconnect® ACCESS • Yellow indicates a Bluetooth® connection error. • Red indicates a user account problem or network connection error.
ALL ABOUT Uconnect® ACCESS 29 • Vehicle must be in range of a usable and authorized cellular signal. • Your smartphone sending the command must be in cellular range to send the command. • Vehicle must be registered with Uconnect® Access and have an active subscription that includes the applicable feature or App. • Owner must have a compatible smartphone and download the Uconnect® Access App. • The vehicle must be properly equipped with factoryinstalled features that enable remote commands. (i.e.
30 ALL ABOUT Uconnect® ACCESS 3. Why can’t all phones use the Uconnect® Access App? The Uconnect® Access App has been designed 1. How much does the Uconnect® Access App cost? to work on most smartphones with the Apple and Uconnect® does not charge for the App, however to Android operating systems. Visit UconnectPhone.com utilize the Remote Services (e.g., Remote Door Lock/ to confirm that your smartphone is compatible with Unlock) a subscription or trial is required to the Uconnect®. Advantage Package. 4.
ALL ABOUT Uconnect® ACCESS 31 Set Up Your Uconnect® Payment Account Setting up your Uconnect® Payment Account allows you to make purchases from your vehicle (such as WiFi Hotspot) and can be used to renew your service at the end of the included trial period. Your Uconnect® Payment Account is optional, but we recommend it so that you can enjoy the full benefits of the system. Setting Up Your Uconnect® Payment Account During Registration 1.
32 ALL ABOUT Uconnect® ACCESS Setting Up After Registration And Managing Your Uconnect® Payment Account If you didn’t set up your Uconnect® Payment Account when you registered, or you want to make changes later on, just go to the Mopar Owner Connect website (www.moparownerconnect.com) to manage your account. 1. Log In to Mopar Owner Connect with your username and password. 2. In the upper-right corner of the screen, click on the “Edit Profile” button. 3.
ALL ABOUT Uconnect® ACCESS 33 • Reviewing you current subscriptions to packages and Apps. • Changing your Uconnect® Payment PIN or your Security Question. • Viewing transaction history of purchases from the Uconnect® Store.
34 ALL ABOUT Uconnect® ACCESS
ALL ABOUT Uconnect® ACCESS 35 Purchasing Apps And WiFi Hotspot For Your Vehicle Apps and WiFi Hotspot can be purchased from the Uconnect® Store from within your vehicle, and online at the Mopar Owner Connect website (moparownerconnect.com). You must first register and set up a Uconnect® Payment account. Purchasing Apps And WiFi Hotspot From Within Your Vehicle: 1. With the vehicle parked and the radio powered on, select the “Apps” button located near the bottom right-hand corner of the radio touchscreen.
36 ALL ABOUT Uconnect® ACCESS 2. To launch the Uconnect® Store, select Apps > All 3. From the Uconnect® Store, select the service you wish Apps > Uconnect® Store. to purchase.
ALL ABOUT Uconnect® ACCESS 37 4. This will launch the selected service or package into 5. The Uconnect® Store will display a “Purchase Overpurchase mode along with providing additional inforview” message confirming the financial details for the mation. The purchase process begins when you press App you are about to purchase. Press the “Purchase” the “Buy” button on the touchscreen. button on the touchscreen to continue.
38 ALL ABOUT Uconnect® ACCESS 6. The User must select “AGREE” to complete the pur- 7. The Uconnect® Store will ask you to “Confirm Paychase. “DISAGREE” will cancel the purchase and ment” using your default payment method on file in re-direct customers back to the Uconnect® Store landyour Uconnect® Payment Account. Press the “Coming page. plete” button on the touchscreen to continue.
ALL ABOUT Uconnect® ACCESS 39 8. The Uconnect® Payment Account will then ask for your “Payment PIN.” After entering this four digit PIN, press the “Continue” button on the touchscreen to make the purchase. NOTE: Purchased Apps and services can take up to 30 minutes to download, depending on your vehicle’s cellular coverage at time of purchase. If your download takes more than 30 minutes, please contact Uconnect® 9.
40 ALL ABOUT Uconnect® ACCESS Purchasing Apps Online From Mopar Owner Connect Website You can also purchase Apps or renew your subscription to a package from the Mopar Owner Connect website. Log In to the Mopar Owner Connect website (moparownerconnect.com) with your username/email and password, and click on the “Store” tab. 1. Log In to Mopar Owner Connect with your username/email and password. 2. Click on the tab that says “Shop.
ALL ABOUT Uconnect® ACCESS 41 3. Click on the link to the Uconnect® Store. 4. You can now browse through the various packages, features and Apps available for your vehicle. Look through your options, read the details, and if you find something you want for your vehicle click on the “Purchase” button.
42 ALL ABOUT Uconnect® ACCESS Using Mopar Owner Connect The Mopar Owner Connect website (moparownerconnect.com) provides you with all the information you need, all in one place. You can track your service history, find recommended accessories for your vehicle, watch videos about your vehicle’s features, and easily access your user guides and manuals. It is also where you can manage your Uconnect® Access account.
ALL ABOUT Uconnect® ACCESS 43 2. Edit Profile: To manage the details of your Uconnect® Access account, such as your contact information, password and PIN, click on the “Edit Profile” button to access the details of your account. 3. Shop: 5. Remote Services: For vehicles with an active Uconnect Access subscription, press one of these icons and enter your four-digit Uconnect® Security PIN to command your vehicle to remotely start, lock/unlock doors or sound the horn and lights.
44 ALL ABOUT Uconnect® ACCESS 1. Log on to the Mopar Owner Connect website (moparownerconnect.com) using the username/email and Click on the “Learn & Use” tab to find user guides and password you used when registering your Uconnect® other information about your vehicle. More specifiAccess system. cally, there is a dedicated Uconnect® Access tab in this section to learn all about your connected vehicle NOTE: If you forgot your username or password, links capabilities.
ALL ABOUT Uconnect® ACCESS 45 5. You can enter up to five mobile phone and/or email addresses to your notifications, and you can customize which ones receive the types of messages. 6. If you add a mobile phone number, you will receive a confirmation text message asking to confirm and receive vehicle notifications. If you are OK with this, reply to the text message saying “yes” (message and data rates may apply, please see your mobile phone provider for details).
46 ALL ABOUT Uconnect® ACCESS Get started with your Uconnect® Access Apps by pressing the Uconnect® “Apps” button on the menu bar at the Getting Started With Apps bottom right corner of the in-vehicle touchscreen. AvailApplications (Apps for short) in your Uconnect® Access able Apps and features are organized by the tabs on the system are designed to deliver the features and services left of the screen. that you want.
ALL ABOUT Uconnect® ACCESS 47 • All Apps — all of your available Apps will reside in 9-1-1 Call the “All Apps” folder. Access To Emergency Services At The Push Of A Button • Running Apps — press this tab to see which Apps are currently running. NOTE: Most Uconnect® Access features do not require that you have a compatible Smartphone. The Uconnect® Access features work using the built-in cellular connection.
48 ALL ABOUT Uconnect® ACCESS Description 9-1-1 Call is a feature that, at the push of a button, can contact emergency services. It’s a convenient way to get in contact with a 9-1-1 operator in the event of an emergency. When the connection between the vehicle and a 9-1-1 operator is made, your vehicle will automatically transmit location information to the 9-1-1 operator. How It Works 2.
ALL ABOUT Uconnect® ACCESS 49 Even if the 9-1-1 Call system is fully functional, factors Vehicles sold in Canada and Mexico DO NOT have 9-1-1 beyond Chrysler Group LLC’s control may prevent or Call system capabilities. 9-1-1 or other emergency line stop 9-1-1 Call system operation. These include, but are operators in Canada and Mexico may not answer or not limited to, the following factors: respond to 9-1-1 system calls.
50 ALL ABOUT Uconnect® ACCESS • Wireless and/or Global Positioning Satellite signals are unavailable or obstructed. • Equipment malfunction at the 9-1-1 operator facility. • Operator error by the 9-1-1 operator. • Wireless network congestion. • Weather. • Buildings, structures, geographic terrain, or tunnels. If your vehicle loses battery power for any reason (including during or after an accident) the 9-1-1 Call System, among other vehicle systems, will not operate.
ALL ABOUT Uconnect® ACCESS 51 • Vehicle must be in range of a usable and authorized cellular signal. • Vehicle must be powered in the ON/RUN or ACC (Accessory) position with a properly functioning electrical system. WARNING! • Never place anything on or near the vehicle’s wireless and GPS antennas. You could prevent wireless and GPS signal reception, which can prevent your vehicle from placing an emergency call. Wireless and GPS signal reception is required for the 9-1-1 Call system to function properly.
52 ALL ABOUT Uconnect® ACCESS WARNING! (Continued) • If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. • Do not add any aftermarket electrical equipment to the vehicle’s electrical system. This may prevent your vehicle from sending a signal to initiate an emergency call.
ALL ABOUT Uconnect® ACCESS 53 Roadside Assistance Call Uconnect® Access In-Vehicle Assistance Features Easy Call To Roadside Assistance 24/7 Using Assist With Uconnect® Access, your vehicle has on-board assisButton tance features located on the rear view mirror designed to enhance your driving experience if you should ever need assistance or support. Description Vehicles equipped with the Uconnect® Access system feature will contain an ASSIST button on the rear view mirror.
54 ALL ABOUT Uconnect® ACCESS • Uconnect® Care — In vehicle support for Uconnect® Access System, Apps, and Features. • Vehicle Care — Total support for your Chrysler Group vehicle. How It Works You or someone in the vehicle simply presses the ASSIST button located on the rear view mirror and you will be presented with your ASSIST options. Make your selection by pressing the screen. Requirements • This feature is available only on vehicles sold in the US.
ALL ABOUT Uconnect® ACCESS 55 • Vehicle must be registered with Uconnect® Access and may share information obtained through such recording have an active subscription that includes the appli- and monitoring in accordance with regulatory requirements. You acknowledge, agree and consent to any cable feature or App. recording, monitoring or sharing of information obtained • Vehicle must be powered in the ON/RUN or ACC through any such call recordings.
56 ALL ABOUT Uconnect® ACCESS Yelp® Here is what Yelp® can do for you while you are on the road: Looking for a burrito joint that is open? A boutique to buy a new pair of jeans? Yelp® is here to help. Use Yelp® • Deliver a list of up to 20 results, prioritizing by best to search for places to eat, shop, relax and play. match, by distance or rating. • Provide up-to-date search listings (pulling the latest information from the cloud).
ALL ABOUT Uconnect® ACCESS 57 How It Works 1. Using the touchscreen, launch Yelp® by pressing Apps > All Apps > Yelp®. 2 OR Using voice recognition, push the say “Launch Yelp®.” button and “Launch Yelp®” Give It A Try! 1. Push the button on the steering wheel and say “Launch Yelp®.” button on the steering wheel and say 2. Push the “Yelp® Search.
58 ALL ABOUT Uconnect® ACCESS 3. Uconnect® will prompt you to say something like, 5. Using the touchscreen, select a restaurant from the list “car wash.” After the beep, say “restaurants.” of search results. 4. The Uconnect® system will link out to the cloud to do 6. Navigate to the location by pressing “Go Now” (if equipped with navigation) Tip: Save your destination to your Yelp® search, and depending on your search Favorites.
ALL ABOUT Uconnect® ACCESS 59 Action Touchscreen Find nearest Nightlife Find nearest Coffee Find nearest Entertainment Find nearest Gas Find nearest Hotels Find nearest Banks Find nearest Parking Find nearest Shopping Find nearest Drugstores Find nearest Urgent Care Find nearest Hospitals Select a POI Select Nightlife Select Coffee Select Entertainment Select Gas Select Hotels Select Banks Select Parking Select Shopping Select Drugstores Select Urgent Care Select Hospitals Select from the list Vo
60 ALL ABOUT Uconnect® ACCESS Action Touchscreen Add a Custom Search Category Delete a Custom Category Press the star to add it Voice Command (VR button on steering wheel) – Press the star to remove it – Press Best Match, Rating, or Distance Press Go Now – Press the star (there is a confirmation pop-up) Press Rating – Press Go Now Press – Press Sort search results by Best Match, Rating or Distance Route to a POI (if equipped) Call a POI (via Bluetooth®) Give It
ALL ABOUT Uconnect® ACCESS 61 • Vehicle must be registered with Uconnect® Access and have an active subscription that includes the appliYelp® provides the ability to save cuscable feature or App. tom search categories by first initiating the search, then pressing the star. To • Vehicle must be powered in the ON/RUN or ACC delete a search category, select it, and (Accessory) position with a properly functioning elecpress the star. A confirmation prompt trical system. will appear to confirm.
62 ALL ABOUT Uconnect® ACCESS • Press the “microphone” on the touchscreen to use voice commands. Safety Information WARNING! • If you wish to cancel a search request, press “Cancel.” • ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume all risks related to the use of the Uconnect® features and applications in this vehicle. Only use Uconnect® when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.
ALL ABOUT Uconnect® ACCESS 63 • To exit Yelp®, press the “X” (close) button in the upper 5. How do I select my final desired location? Make your right corner of the touchscreen. final selection by pressing the desired POI name in your search result list. Voice recognition is not supFAQs ported for the final POI selection. 1. Is there a Help menu within the Yelp® App? No, but 6.
64 ALL ABOUT Uconnect® ACCESS 8. What is the difference between Yelp® and onboard 9. Why doesn’t Yelp® recognize my Voice Command navigation? Both experiences are slightly different, search request? To Search Yelp®, Uconnect® must establish a connection to the Yelp® cloud-based serbut may yield the same results. For example, while vice, using the built in 3G connection in your both the onboard navigation system and Yelp® conUconnect® Access system.
ALL ABOUT Uconnect® ACCESS 65 11. Can I use Yelp® to search for places based on my end destination, instead of just places around me? Yes, you can say “Pizza in Chicago,” and add it as a stop on your road trip. Theft Alarm Notification Should you receive a notification that your theft alarm has been set-off, please react with caution. There are a number of reasons why your alarm may have been triggered, one of which could be that your vehicle was stolen.
66 ALL ABOUT Uconnect® ACCESS 2. Once logged in you will find yourself on the Dash- 7. You’re all set. Should your theft alarm go off, a board. Click on the “Edit Profile” button in the uppernotification(s) will be sent to the number(s) and/or email(s) you provided. right corner of the page. 3. Click on the “Notifications” tab on the left side of the Requirements page. • Vehicle must be properly equipped with the Uconnect® Access System and a factory installed Theft Alarm sys4.
ALL ABOUT Uconnect® ACCESS 67 CAUTION! In the event your theft alarm is activated, use caution and evaluate the situation from a safe distance. If any unauthorized or suspicious person is near or inside of your vehicle, immediately contact the police. Do not do anything that could jeopardize your safety or the safety of those around you. 2. How can I change where I receive notifications? You can manage your notifications by going to the Mopar Owner Connect website (moparownerconnect.
68 ALL ABOUT Uconnect® ACCESS Stolen Vehicle Assistance is a secure process that can only be done with your permission. Law enforcement gets involved If your vehicle is ever stolen, this App (with your only after you file a stolen vehicle report with them. permission) can provide its location to the law enforceHow It Works ment to help them track it down. Stolen Vehicle Assistance Description 1. If your vehicle is stolen, contact local law enforcement as soon as possible.
ALL ABOUT Uconnect® ACCESS 69 3. Uconnect® Care will authenticate that you are the Disclaimers owner of the vehicle and contact the law enforcement • No security system is invincible, and vehicle thieves with whom you filed the stolen vehicle report. may develop ways to prevent your vehicle from being located. 4. Uconnect® Care will work with your local law enforcement to track and attempt to recover the vehicle. FAQs You will be contacted by law enforcement if your vehicle is recovered.
70 ALL ABOUT Uconnect® ACCESS that someone is not tracking your vehicle for purposes WiFi Hotspot other than at your request to locate it in the event it is stolen. 3. How will I know if my vehicle is recovered? After you provide the Uconnect® Care Agent with the stolen vehicle report, the agent will work together with law enforcement to try to locate your vehicle. If your vehicle is recovered, you will be contacted by law enforcement.
ALL ABOUT Uconnect® ACCESS 71 WARNING! The WiFi Hotspot feature provides the vehicle passengers with an internet access hot spot in the vehicle, using the radio as an access point. The hot spot will allow WiFi enabled in-vehicle devices (such as a laptop or any other portable enabled media device) to wirelessly connect to Enables all your passengers to be simultaneously the internet. connected to the web. Give it a Try! Connect several devices at one time. 1.
72 ALL ABOUT Uconnect® ACCESS NOTE: You must set up your Uconnect® Payment Account on the Mopar Owner Connect website and establish a Uconnect® Payment PIN to purchase WiFi Hotspot. 2. After purchasing WiFi Hotspot, it will be enabled/ turned on in your vehicle. The WiFi Hotspot App can be found on your in-vehicle touchscreen by selecting Apps > All Apps > WiFi Hotspot.
ALL ABOUT Uconnect® ACCESS 73 3. WiFi Hotspot should be turned on after purchasing a subscription. To disable WiFi Hotspot, simply press to uncheck the box to the right of the App (this feature is available while the vehicle is in motion).
74 ALL ABOUT Uconnect® ACCESS Optional: Give your hot spot a unique name by 4. From your in-vehicle touchscreen, select the appropriate pressing Hotspot Name (key pad is not available in-vehicle network and the desired security level setwhile vehicle is in motion). ting. Each security level has different pass phrase constraints. Change the security level setting by selecting the checkbox for any of the following security settings.
ALL ABOUT Uconnect® ACCESS 75 5. From your Wi-Fi enabled device (laptop, tablet, etc.) • Search for and select the Uconnect® hotspot in the settings of your device • Type the network security key (this is called “pass phrase” and is found in Apps > All Apps > WiFi Hotspot > View/Edit Pass phrase) • Click OK You are now connected! NOTE: Refer to your device’s owner’s manual for specific information related to your device.
76 ALL ABOUT Uconnect® ACCESS • Vehicle must be registered with Uconnect® Access and have an active WiFi Hotspot subscription ( WiFi Outpost will be turned off if there is no active subscription). • Vehicle must be in the ON/RUN or ACC (Accessory) position and have a properly operating electrical system for any of the in-vehicle Uconnect® features to function.
ALL ABOUT Uconnect® ACCESS 77 • While the vehicle is in motion it is possible to enable or Tips And Shortcuts disable the WiFi Hotspot. Simply press to check or • Give your WiFi Hotspot a unique name by pressing uncheck the box to the right of the App. “Hotspot Name” within the WiFi Hotspot App. • For your own safety, it is not possible to use some of • To view a list of connected devices, press “View the touchscreen features while the vehicle is in motion.
78 ALL ABOUT Uconnect® ACCESS 4. What if I want to create a custom password for my connection? Select either WPA2/WPA or the WEP 1. How do I know if I have a good signal strength? setting and create a pass phrase by pressing Apps > There is a signal strength indicator on the Apps button All Apps > WiFi Hotspot > View/Edit Pass phrase. of the radio touchscreen. 5. I do not see the connection on my wireless laptop or 2.
ALL ABOUT Uconnect® ACCESS 79 SRT Performance Pages/SRT Performance Pages Plus or SD card, allowing for easy sharing of your driving performance. With SRT Performance Pages Plus, drivers can also download the data to the web. Save And Share Your Best Performance Results With The SRT Performance Pages App. (Available Only On (*Some information will only be available when vehicle is not in motion.) SRT Performance Vehicles.
80 ALL ABOUT Uconnect® ACCESS 4. The Performance Pages App home page will display with a vehicle graphic and menu item button on the touchscreen on the left. 5. You can navigate between the Menu item performance button tabs on the left side of screen.
ALL ABOUT Uconnect® ACCESS 81 2 1 — Home 2 — Timers 3 — G-Force 4 — Gauges 1 5 — “Scroll Down” Button 1 — Gauges 2 2 — Engine 3 — Options 4 — “Scroll Up” Button
82 ALL ABOUT Uconnect® ACCESS 6. If you chose the Timers tab, you will get an overview of vehicle run time stats. You can view and compare driving performance by choosing between your “Best”, “Last” and “Current” run times. This data can be saved, downloaded and shared.
ALL ABOUT Uconnect® ACCESS 83 2 Downloading Timers Data Choosing the Save button on the touchscreen allows you to save your run ticket. Data saved will include date, time stamp, timer data, brake distance and brake speed.
84 ALL ABOUT Uconnect® ACCESS If you want to download the Timers information, a message on the ticket on the radio touchscreen will give you three options on where you want to download data: USB, SD Card or Website. Web — If you choose “Website,” the embedded cellular connection will automatically save the file to the Mopar Owner Connect website (moparownerconnect.com). You will need to logon to this URL and download the ticket as needed.
ALL ABOUT Uconnect® ACCESS 85 Once the option to Save is selected, you will receive a confirmation notification. If you selected to save to the website, the URL will be provided where you can view performance data and download the ticket. Only the 10 most recent saved runs will be stored and available on the website, so the oldest run will be overwritten for another if there are already 10. Each saved run will be stored on the website until it is overwritten.
86 ALL ABOUT Uconnect® ACCESS • Lateral G-force — Measures the left and right turning force of the vehicle. • Longitudinal G-force — The longitudinal g-force will measure the acceleration and braking force of the vehicle. • G-force visual — Visual of the current amount of g-force the vehicle is producing, either longitudinal or lateral. 8. If the Gauges 1 tab is chosen, you will see a display of vehicle gauges. Information displayed will be the same as on the instrument cluster such as: 9.
ALL ABOUT Uconnect® ACCESS 87 10. If the Engine tab is chosen, you will see a display of 11. If the Options tab is chosen, it will allow the driver to real-time engine data that will be the same as disadd details to the graphic display of the vehicle on played on the instrument cluster such as: the radio touchscreen such as: • Speedometer — Current speed reading. • Home Picture — select a vehicle image to be displayed. Pressing the home picture option will allow • Horsepower — Current horsepower reading.
88 ALL ABOUT Uconnect® ACCESS NOTE: Graphic will represent the owner’s vehicle, e.g. Give It A Try! Viper or Grand Cherokee. 1. Bring vehicle to a complete stop, but leave vehicle ON • Vehicle Color Options — customize the color of the in order for the instrument gauges to be active. vehicle displayed on the home picture. 2. Select the “Apps” button at bottom of radio touch• Accept Button — saves your selections. screen. 3. Select the “Information Apps” button on left side of radio. 4.
ALL ABOUT Uconnect® ACCESS 89 7. Bring the vehicle to a complete stop after reaching the • Vehicle must be powered in the ON/RUN or ACC target speed or distance. (Accessory) position with a properly functioning electrical system. 8.
90 ALL ABOUT Uconnect® ACCESS • Upon accessing the Timers screen after an ignition FAQs cycle and/or battery disconnect, the driver will see the 1. How do I get SRT Performance Pages? This App is “Best” set of values for all performance indicators, as pre-loaded from the factory. received from the cluster. 2. Do I turn Performance Pages “ON” or “OFF” at any • If accessing Timers screen after an ignition cycle time? No.
ALL ABOUT Uconnect® ACCESS 91 5. What is the difference between SRT Performance 9. What are “Timer Constraints” or criteria that needs to be met to show performance data? Pages and SRT Performance Pages Plus? SRT Performance Pages Plus gives you the additional option to • 0-60 MPH or 0-100 kph ET reached within 10 seconds save performance data to the web. • Distance of 1/4 mile and 1/8 mile • Brake timer when traveling > 30 MPH 6.
92 ALL ABOUT Uconnect® ACCESS UconnectPhone.com. iPhone® and some other smartphones do not currently support Bluetooth® MAP. Ensure Add Free-Form Voice Texts To Your Voice Text Reply MAP is ON and incoming message notification is enabled. Feature How It Works Description Set Up Your Phone To Work With Voice Texting This Voice Texting enhances the Voice Text Reply feature built into your Uconnect® Access 8.4A and 8.4AN radio.
ALL ABOUT Uconnect® ACCESS 93 NOTE: If Phone Supports MAP Then ensure MAP is On and incoming message notification is enabled, (see UconnectPhone.com for phone specific instructions) 2. Generic Phone Setup Instructions (your phone’s setup process may be similar): 1. On phone select “Settings” (or the equivalent on your phone) 2. Select Wireless/Bluetooth® settings 3. Ensure Bluetooth® is on (box checked) 4. Select Bluetooth® Settings 1.
94 ALL ABOUT Uconnect® ACCESS 9. Hit the back button twice to return to the Bluetooth® Dictate A Free-Form Reply To A Message From Radio (Voice Text Reply) Settings screen 10. Check the box for Discoverable If a Bluetooth® Authorization window appears showing your phone requesting permissions, check the box for Always and Hit Accept. Sending A New Text Message From Radio 1. Push on the steering wheel. 2. Say “Send text message” 1.
ALL ABOUT Uconnect® ACCESS 95 4. The system will repeat the message you dictated and To Reply To A Message With A Pre-Formatted Restate available commands. If your message was too sponse (Voice Text Reply) long, the system will respond with “Your message was too long. Your message was truncated.” Say “Send,” or “Start Over” or “Continue.” 5. Say “Continue” OR Say “Start over” OR Say “Repeat” OR Say “Send” OR NOTE: This function only operates while the vehicle is not in motion. Say “Cancel.” 1.
96 ALL ABOUT Uconnect® ACCESS 3. Select the pre-formatted response by pressing it (“I Viewing Your Messages can’t talk right now”) 1. Push the “Phone” button on the steering wheel. 4. Press “Send” Viewing Or Listening To Incoming Messages To Listen to a Message from Radio 1. Push the ⬙Phone⬙ button on the steering wheel. Say ⴖListen to messageⴖ OR Press the ⬙Listen⬙ button on the touchscreen.
ALL ABOUT Uconnect® ACCESS 97 2 2. Say “View message” OR Press “View” on the in-vehicle touchscreen. Contact names or phone numbers of the message sender appears in a list along with View and Listen buttons on the touchscreen.
98 ALL ABOUT Uconnect® ACCESS For example, if the system is explaining all of the options available after dictating a text message, at any time the 1. Press “View” next to the contact name/phone number user can press ⬙Listen⬙ on touchscreen or push the of the message you want to be displayed. ⬙Phone⬙ button on the steering wheel and say ⬙Listen.⬙ OR Requirements Say “Show message n” • (MAP may not be compatible with Apple iPhones® (pre n = the number of the message iOS 6).
ALL ABOUT Uconnect® ACCESS 99 • Customer must have a properly paired and connected • Chrysler Uconnect® and its affiliates are not responcellular device with Bluetooth® Message Access Prosible for errant text messages. file (MAP) enabled. Voice Texting is compatible with • Vehicle must be registered with an active Uconnect® many newer BlackBerry and Android mobile devices. Access trial or paid subscription. Apple iOS 5 and earlier does not support MAP so iPhones will not send free form text messages.
100 ALL ABOUT Uconnect® ACCESS FAQs (Some phones will support pre-formatted responses, but not free-form. Refer to UconnectPhone.com for further details.) 1. Can I still voice text if my phone is not listed? We are constantly testing phones and updating our compatibility database. If your phone is not listed, you may 4.
ALL ABOUT Uconnect® ACCESS 101 7. Can I voice text my car? The Voice Texting feature 10. Can I use Text Messaging if the “messaging” button allows you to listen to, and reply to text messages doesn’t turn white? Only MAP compatible phones (SMS) sent to your portable cellular mobile phone by will work with Text Messaging. If your phone is voice while in your vehicle. compatible, the “messaging” light will turn white, after the phone is Bluetooth® connected, and you 8.
102 ALL ABOUT Uconnect® ACCESS If you want, you can set up notifications for your account Lock Or Unlock Your Vehicle From Virtually Anywhere to receive an email or text (SMS) message every time a command is sent to lock or unlock your doors. Using Your Computer Or Smartphone App. How It Works Description Remote Door Lock/Unlock The Remote Door Lock/Unlock feature provides you the Uconnect® Access App: ability to lock or unlock the door on your vehicle, 1.
ALL ABOUT Uconnect® ACCESS 103 4. The Uconnect® Access App will confirm if your command was sent (or not). Press “OK” to close the pop-up screen. 5. It will take a little while for the command to go through to your vehicle. The time it takes depends on a number of technical conditions. 6. A message will appear on the screen to let you know if the command was received by your vehicle. 3.
104 ALL ABOUT Uconnect® ACCESS Mopar® Owner Connect website: 1. Log on to the Mopar® Owner Connect website (moparownerconnect.com) using the username and password you used when registering your Uconnect® Access system. NOTE: If you forgot your username or password, links are provided on the website to help you retrieve them. 2. If you have more than one vehicle registered into the Mopar® Owner Connect website (moparownerconnect.
ALL ABOUT Uconnect® ACCESS 105 3. After providing your Uconnect® Security PIN, you can ask them to lock or unlock your vehicle. The agent will 1. If you need to unlock the doors of your vehicle, send a command to your vehicle to get the task done. contact Uconnect® Care by calling 855-792-4241. Give It A Try! NOTE: The Uconnect® Care agents are trained to help you with unlocking of your door (for example, in an • Download the Uconnect® Access App to your smartphone. accidental lock-out).
106 ALL ABOUT Uconnect® ACCESS • Your request will typically take about to 3 minutes to • An ignition cycle is required for some remote comprocess. If your vehicle has been parked for a while it mands such as Remote Vehicle Start and Remote Door Lock/Unlock if following a Remote Horn and Lights can take up to 30 minutes for the request to reach your activation. vehicle and perform the task. Requirements FAQs • Vehicle must be properly equipped with the 1.
ALL ABOUT Uconnect® ACCESS 107 3. Will my vehicle be safe if I lose my smartphone? People sometimes lose their phone, which is why security measures have been engineered into the Uconnect® Access App. Asking for your username, password and Uconnect® Security PIN help to ensure that nobody can get into your vehicle if they happen to find your smartphone. 4.
108 ALL ABOUT Uconnect® ACCESS You can also send a command to turn-off an engine that has been remote started. After 15 minutes if you have not entered your vehicle with the key, the engine will shut off automatically. This remote function requires your vehicle to be equipped with a factory-installed Remote Start system. If you want, you can set-up notifications for your account to receive an email or text (SMS) message every time a command is sent to remote start or cancel a remote start.
ALL ABOUT Uconnect® ACCESS 109 4. The Uconnect® Access App will confirm if your NOTE: If you forgot your username or password, links command was sent (or not). Press “OK” to close the are provided on the website to help you retrieve them. pop-up screen. 2. If you have more than one vehicle registered 5. It will take a little while for the command to go into the Mopar Owner Connect website through to your vehicle. The time it takes depends on (moparownerconnect.
110 ALL ABOUT Uconnect® ACCESS Uconnect® Care: 1. If you need to unlock the doors of your vehicle, contact Uconnect® Care by calling 855-792-4241. NOTE: The Uconnect® Care Agents are trained to help you with unlocking of your door (for example, in an accidental lock-out). All other Remote Services should be performed via the Mopar Owner Connect website (moparownerconnect.com) or through the Uconnect® Access App on your compatible smartphone. Mopar® Owner Connect Remote Vehicle Start 2.
ALL ABOUT Uconnect® ACCESS 111 Give It A Try! Requirements • Download the Uconnect® Access App to your smart- • Vehicle must be properly equipped with the Uconnect® Access System and factory installed Remote Start capaphone. bilities. • Enter the username and password that you established for the Mopar Owner Connect website (moparowner- • Vehicle must be in range of a usable and authorized cellular signal. connect.com) during registration of your new vehicle.
112 ALL ABOUT Uconnect® ACCESS FAQs 4. Can someone drive off with my vehicle using the App? No. Driving your vehicle still requires the keys to be in the vehicle. The Remote Start feature simply starts the engine to warm-up or cool down the interior before you arrive, you cannot drive away without the keys. 1.
ALL ABOUT Uconnect® ACCESS 113 If you want, you can set-up notifications for your account to receive an email or text (SMS) message every time a Can’t Find Your Vehicle In The Parking Lot? Sound The command is sent to turn on the horn and lights. Horn And Flash The Lights On Your Vehicle To Locate It. How It Works Description Remote Horn And Lights It is easy to locate a vehicle in a dark, crowded or noisy 1.
114 ALL ABOUT Uconnect® ACCESS 4. The Uconnect® Access App will confirm if your 2. If you have more than one vehicle registered command was sent (or not). Press “OK” to close the into the Mopar Owner Connect website (moparownerconnect.com), select the vehicle you pop-up screen. want to send the command by clicking on its image 5. It will take a little while for the command to go along the top. through to your vehicle. The time it takes depends on 3.
ALL ABOUT Uconnect® ACCESS 115 4. You will then be asked to enter your Uconnect® Security PIN (this is the same 4-digit code established when your registered your Uconnect® Access system). Please enter your Uconnect® Security PIN. 5. A message will appear on the screen to let you know if the command was received by your vehicle. Uconnect® Care: 1. If you need to unlock the doors of your vehicle, contact Uconnect® Care by calling 855-792-4241.
116 ALL ABOUT Uconnect® ACCESS 2. For security purposes, the Uconnect® Care agent will • Push the button to sound your vehicle’s horn and flash verify your identity by asking for your 4-digit the lights. Uconnect® Security PIN. • Your request will typically take about to three minutes 3. After providing your Uconnect® Security PIN, you to process. If your vehicle has been parked for a while can ask them to lock or unlock your vehicle.
ALL ABOUT Uconnect® ACCESS 117 • If using the Uconnect® Access App to command your FAQs vehicle, your smartphone must be compatible and in 1. How long does it take to sound my horn and flash range of a cellular signal.
118 ALL ABOUT Uconnect® ACCESS 4. How do I turn off the horn and lights after I turn them on? By pressing the “horn icon” a second time on your Uconnect® Access App, a second command will be sent to shutoff the horn and lights. Alternatively, if you are close enough to the vehicle you can use the Key Fob to turn off the horn and lights by pressing the “Panic” button. Via Mobile Apps Determine If Your Vehicle Is Via Mobile-Enabled To see if your Uconnect® 8.4A or 8.
ALL ABOUT Uconnect® ACCESS 119 Pandora® — If Equipped • Listen to previously created stations in “shuffle” mode Pandora® gives people the music and comedy they love • For the best music experience, continuously personalanytime, anywhere. Personalized stations launch instantly, ize your music using the “Like” or “Dislike” buttons with the input of a favorite artist, track, comedian, or genre. on the touchscreen whenever a particular song is played that you want to hear more or less of.
120 ALL ABOUT Uconnect® ACCESS How It Works 3. Next, link app accounts to your Via Mobile profile by entering your login information for Pandora®. Via Mobile uses the Uconnect® Access smartphone app If you’ve already registered with Uconnect® Access, and your smartphone’s data plan to access your personal log in to MoparOwnerConnect.com to set up your Via Pandora® account from the vehicle and control it using Mobile profile. Click on “Via Mobile Profile.” the vehicle touchscreen.
ALL ABOUT Uconnect® ACCESS 121 5. Launch the Uconnect® Access app on your connected smartphone and log in with your Mopar Owner Connect Username/Email and password. From the vehicle touchscreen press the “Apps” button and select Pandora® from the list. Pandora® is located within the “All Apps” tab. To launch Pandora® using voice recognition, push the button on the steering wheel and say, “launch Pandora via Mobile.
122 ALL ABOUT Uconnect® ACCESS Each time you want to use a Via Mobile app in your vehicle, the Uconnect® Access App must be running on your smartphone and the smartphone must be paired via Bluetooth®.
ALL ABOUT Uconnect® ACCESS 123 A message will be displayed to remind you that Via Mobile apps utilize the data plan on your connected smartphone to provide content. Touch “OK” to continue or the “X” to exit. NOTE: Many smartphones have a limit to how much data they can utilize before incurring additional charges. The amount of data being used varies by smartphone device, cellular service provider and specific app. Check your smartphone service plan for more details.
124 ALL ABOUT Uconnect® ACCESS 3. To go back and select a different station, press the “Station List” button on the touchscreen. Requirements • Vehicle must be properly equipped with the Uconnect® Access System • Your smartphone must be compatible with the Uconnect® Access App and properly connected to the vehicle • Your connected smartphone must be in range of a usable cellular signal Give it a try! 1.
ALL ABOUT Uconnect® ACCESS 125 Tips and Shortcuts • Pandora® will launch with the last setting and play list you chose. To change this, select the “Station List” button on the touchscreen in lower left corner to select another station. The Uconnect® Access App must be open and you must be logged in. A blue light indicates that it’s providing data to the vehicle. • If you recently changed your password for Pandora®, it may need to be updated on Mopar Owner Connect under the “Via Mobile” section.
126 ALL ABOUT Uconnect® ACCESS 5. Can I customize my Pandora® stations? The 8. How do I block explicit content? Customers have the ability to block explicit content by adjusting their “Thumbs up” and “Thumbs down” bsutton on the settings through the Pandora® website at pandoratouchscreens are used to personalize stations based on .com or through the Pandora® mobile app. the currently playing track. Give a track the “thumbs up” to hear more tracks with similar qualities, or 9.
ALL ABOUT Uconnect® ACCESS 127 iHeartRadio — If Equipped • Launch iHeartRadio using Voice Recognition (VR) or through touchscreen controls. iHeartRadio provides instant access to more than 1,500 live radio stations from across the country and allows • Browse, listen, and save radio stations for easy access. listeners to create custom music stations inspired by their • Browse and create custom stations (e.g. Zac Brown favorite artists or songs. Band).
128 ALL ABOUT Uconnect® ACCESS 3. Next, link app accounts to your Via Mobile profile by entering your login information for apps like iHeartVia Mobile uses the Uconnect® Access smartphone app Radio. and your smartphone’s data plan to access your personal If you’ve already registered with Uconnect® Access, iHeartRadio account from the vehicle and control it using log in to MoparOwnerConnect.com to set up your Via the vehicle touchscreen. A compatible smartphone is Mobile profile.
ALL ABOUT Uconnect® ACCESS 129 5. Launch the Uconnect® Access app on your connected smartphone and log in with your Mopar Owner Connect Username/Email and password. From the vehicle touchscreen press the “Apps” button and select iHeartRadio from the list. iHeartRadio is located within the “All Apps” tab. To launch iHeartRadio using voice recognition, push the button on the steering wheel and say, “launch iHeartRadio via Mobile”.
130 ALL ABOUT Uconnect® ACCESS Each time you want to use a Via Mobile app in your vehicle, the Uconnect® Access App must be running on your smartphone and the smartphone must be paired via Bluetooth®.
ALL ABOUT Uconnect® ACCESS 131 A message will be displayed to remind you that Via Mobile apps utilize the data plan on your connected smartphone to provide content. Touch “OK” to continue or the “X” to exit. NOTE: Many smartphones have a limit to how much data they can utilize before incurring additional charges. The amount of data being used varies by smartphone device, cellular service provider and specific app. Check your smartphone service plan for more details.
132 ALL ABOUT Uconnect® ACCESS Give it a try! 2. The app will launch, presenting you with a convenient interface to use while in your vehicle. You will have four options to select from: • My Stations – Access stations you’ve saved and created • Stations Near You – Listen to live radio stations broadcasting from your local area • Live Radio – Displays live radio stations organized by state and city (“Stations by Location”) and genres (“Music” and “Talk Radio.
ALL ABOUT Uconnect® ACCESS 133 4. Touch “Featured Artists by Genre” • Select an artist from the list Requirements • Vehicle must be properly equipped with the Uconnect® Access System 5.
134 ALL ABOUT Uconnect® ACCESS Tips and Shortcuts FAQs • Continually refine stations to your liking using the 1. Why can’t I get iHeartRadio via Mobile to work? Here are some things to consider: Thumbs Up or Thumbs Down controls • Check to ensure you have linked your iHeartRadio • Press the “HOLD to Set” button on the top of the account credentials with Uconnect® Access. This is screen for three seconds to add current station as a usually done during registration and setup. Then, preset.
ALL ABOUT Uconnect® ACCESS 135 2. How do I personalize the music played on my 5. Can I create an iHeartRadio account during custom station? Press the “thumbs up” icon when Uconnect® Access registration and set-up? There is a music is played that you like, and the “thumbs down” link from the Via Mobile profile page where the icon when music is played that you do not like. Future customer can go to iHeartRadio’s website to create a music played will give you more of the music with new account.
136 ALL ABOUT Uconnect® ACCESS 9. How do I know how much data is being used? • Reduce the need to use your smartphone to access Slacker so you can stay focused on driving. Uconnect® Access via Mobile uses your smartphone’s existing data plan to stream content. Data usage varies • Launch Slacker using Voice Recognition (VR) or by phone/device, content (e.g. videos), high quality through touchscreen controls. audio and several other factors. Please refer to your • Leverage existing Slacker account.
ALL ABOUT Uconnect® ACCESS 137 • Listen to customized stations based on your favorite 1. If you have not registered with Uconnect® Access, artists and music. begin by pressing the “Apps” button on the touchscreen inside your vehicle, and then press “Uconnect • Continually refine stations to your liking using the Registration.” “Heart,” “Ban Artist” or “Ban Song” controls. 2.
138 ALL ABOUT Uconnect® ACCESS 4. Next, connect your smartphone to the vehicle touchscreen. The Uconnect® Access app is compatible with select iPhone® and Android smartphones. Visit UconnectPhone.com to confirm that your smartphone is compatible with Uconnect®. Once you’ve confirmed your smartphone is compatible, pair it to the vehicle touchscreen via Bluetooth® to use Via Mobile apps. If using an iPhone®, a USB cable may also be supported for the data connection. 5.
ALL ABOUT Uconnect® ACCESS 139 2 Each time you want to use a Via Mobile app in your vehicle, the Uconnect® Access App must be running on your smartphone and the smartphone must be paired via Bluetooth®.
140 ALL ABOUT Uconnect® ACCESS A message will be displayed to remind you that Via Mobile apps utilize the data plan on your connected smartphone to provide content. Press “OK” to continue or the “X” to exit. NOTE: Many smartphones have a limit to how much data they can utilize before incurring additional charges. The amount of data being used varies by smartphone device, cellular service provider and specific app. Check your smartphone service plan for more details.
ALL ABOUT Uconnect® ACCESS 141 Your chosen station will play. Use the “Heart” and “Ban” buttons on the touchscreen to quickly and easily customize your experience. Like a song? Heart it to hear it more often. Dislike a song? Ban it and the song or artist will be removed from your station. Slacker makes it easy and personal. Requirements • Vehicle must be properly equipped with the Uconnect® Access System.
142 ALL ABOUT Uconnect® ACCESS • Vehicle must be powered in the ON/RUN or ACC (Accessory) position with a properly functioning electrical system. Tips and Shortcuts • Continue to use the “like” icon (Heart), and “dislike” icon (circle with line through it) to confirm your music preferences and refine the music being played on that station. check to ensure you have properly connected your compatible smartphone to the vehicle touchscreen. The Uconnect® Access App must be open and you must be logged in.
ALL ABOUT Uconnect® ACCESS 143 3. How do I know when Slacker is playing one of the 7. Can I create custom content from within the vehicle? songs I indicated I “liked”? The heart button on the To create a custom station, visit Slacker’s website at slacker.com or the Slacker mobile app. Custom content touchscreen will appear in yellow when playing a cannot be created from within the vehicle. song you previously liked. When you see it appear in yellow, you do not need to “like” it again, and you 8.
144 ALL ABOUT Uconnect® ACCESS • Aha™ gives customers the flexibility to create up to 30 pre-set stations from within the vehicle, on the Aha™ Aha™ makes it easy to instantly access your favorite Web website (aharadio.com), or through the Aha™ mobile app. content on the go.
ALL ABOUT Uconnect® ACCESS 145 How It Works 3. Next, link app accounts to your Via Mobile profile by entering your login information for Aha™. Via Mobile uses the Uconnect® Access smartphone app If you have already registered with Uconnect® Access, and your smartphone’s data plan to access your personal log in to MoparOwnerConnect.com to set up your Via Aha™ account from the vehicle and control it using the Mobile profile. Click on “Via Mobile Profile.” vehicle touchscreen.
146 ALL ABOUT Uconnect® ACCESS 5. Launch the Uconnect® Access app on your connected smartphone and log in with your Mopar Owner Connect Username/Email and password. From the vehicle touchscreen press the ⬙Apps⬙ button and select Aha™ from the list. Aha™ is located within the “All Apps” tab. To launch Aha™ using voice recognition, push the VR button on the steering wheel and say, “launch Aha via Mobile.” Ensure that Via Mobile data has been turned on under “Settings” in the Uconnect® Access App.
ALL ABOUT Uconnect® ACCESS 147 2 Each time you want to use a Via Mobile app in your vehicle, the Uconnect® Access App must be running on your smartphone and the smartphone must be paired via Bluetooth®.
148 ALL ABOUT Uconnect® ACCESS A message will be displayed to remind you that Via Mobile apps utilize the data plan on your connected smartphone to provide content. Touch “OK” to continue or the “X” to exit. NOTE: Many smartphones have a limit to how much data they can utilize before incurring additional charges. The amount of data being used varies by smartphone device, cellular service provider and the specific app. Check your smartphone service plan for more details.
ALL ABOUT Uconnect® ACCESS 149 within the vehicle, from the Aha™ website, or through the Aha™ mobile app. Some stations may not be available on Aha™. Give it a try! 2. Select an Aha™ station. Your chosen station will play. Refine the content for select stations using the “Like” and “Dislike” buttons on the touchscreens.
150 ALL ABOUT Uconnect® ACCESS You can associate your Aha™ account with your personal • Vehicle must be registered with Uconnect® Access and have an active subscription that includes the appliFacebook®, Twitter® and Slacker accounts. If you have the cable feature or app. Aha™ app downloaded to your smartphone visit the Aha™ settings screen and look for “Associate Accounts.” You can • Vehicle must be powered in the ON/RUN or ACC also associate your Aha™ account from aharadio.com.
ALL ABOUT Uconnect® ACCESS 151 FAQs 2. How does Aha™ help refine my music options? It organizes your favorite content into personalized ondemand radio stations. You can access podcasts, internet radio, personalized traffic reports and even restaurant recommendations. It will assemble content for you based on your use of the “like” and “dislike” buttons on the touchscreen. 1.
152 ALL ABOUT Uconnect® ACCESS 5. If I enter personalized preferences on the web, will it 8. How do I set up an Aha™ account? You can create an account with Aha™ by visiting aharadio.com. To also save my setting when I am in the vehicle? Yes, make changes to an existing Aha™ account, visit the your personalized selections are saved to a common Aha™ website. area, so they will be reflected wherever you access Aha™ in the vehicle on the vehicle touchscreen, 9.
ALL ABOUT Uconnect® ACCESS 153 11. Should I have the Aha™ app downloaded to my smartphone to use Aha™ via Mobile? You do not need to have the Aha™ app on your smartphone to use Aha™ via Mobile. The Uconnect® Access App is required. 12. How do I know how much data is being used? Uconnect® Access via Mobile uses your smartphone’s existing data plan to stream content. Data usage varies by phone/device, content (e.g. videos), high quality audio and several other factors.
154 ALL ABOUT Uconnect® ACCESS 2. In “My Apps,” select “Settings” and then “Reinstall App” and “Continue.
ALL ABOUT Uconnect® ACCESS 155 2
156 ALL ABOUT Uconnect® ACCESS 3. Your Apps have been successfully re-installed. Connect website (moparownerconnect.com). On Mopar Owner Connect, go to Uconnect® Store, and click on “Remove My Vehicle.” For further assistance 855-792-4241. call Uconnect® Care at 1. Press the Uconnect® App and open the Uconnect® Store and go to “My Apps.” How To Remove My Uconnect® Access Account To remove your Uconnect® Access account or cancel your Uconnect® Access subscription, follow the instructions below.
ALL ABOUT Uconnect® ACCESS 157 2 2. In “My Apps”, select “Settings” and then “Remove Uconnect® Account” and “Continue.
158 ALL ABOUT Uconnect® ACCESS
ALL ABOUT Uconnect® ACCESS 159 Uconnect® Care & FAQs For additional information about Uconnect® Access, push the ASSIST button on the rear view mirror and then select Uconnect® Care on your in-vehicle touchscreen to contact Uconnect® Care. Your call will be directed to a Uconnect® Care agent or held in a queue until an agent is available. You can also phone Uconnect® Care directly at 855-792-4241, or go to the Mopar Owner Connect website (moparownerconnect.com).
160 ALL ABOUT Uconnect® ACCESS 2. Why Do I Need An Email Address? selecting Edit Profile on the Mopar Owner Connect website (moparownerconnect.com), or you can call Uconnect® Care at 855-792-4241. Without an email address, customers cannot register for Uconnect® Access. Customers need to register so they can subscribe to receive additional services and 5. How Do I Create A Uconnect® Payment PIN? create a Uconnect® Security PIN for remote command Log into the Mopar Owner Connect website (moprequests.
ALL ABOUT Uconnect® ACCESS 161 7. What If I Forgot My Uconnect® Payment PIN? The next time you are asked for your Uconnect® Payment PIN, select “Forgot PIN?” and follow the steps to reset it. a. Log in to the Mopar Owner Connect website (moparownerconnect.com) then select Edit Profile to edit your personal information. b. Make your edits and click “Save.” 8. How Do I Update My Uconnect® Payment Account 10.
162 ALL ABOUT Uconnect® ACCESS 12. Can I Access The Uconnect® Store While I Am 15. How Do I Manage My Notification Preferences? Driving? Go to Edit Profile > Uconnect® Notifications on the Mopar Owner Connect website (moparownerconNo, some applications and services are not available while driving. Only use Uconnect® when it is safe to nect.com). do so. 16. Do I Receive A Purchase Confirmation? 13. How Do I Know When A New App, Feature Or Yes.
ALL ABOUT Uconnect® ACCESS 163 c. Follow the steps to enter your Uconnect® Payment 20. Which Apps Are Included With My Vehicle? PIN and complete the process. Go to Uconnect® Store > My Apps to see Apps currently available on your vehicle. You can also go to the Uconnect® Store online at Mopar Owner Connect (moparownerconnect.com), 21. If I Delete/Remove A Package From My Screen, select the Shop tab, then Uconnect® Store.
164 ALL ABOUT Uconnect® ACCESS 24. Can I Cancel A Subscription Before It Expires? Yes, but your subscription will still be active until the expiration date. If you subscribe to another package, the new subscription will start immediately. 25. Do I Have To Keep My Vehicle On During The App Download Process? Yes. 26. How Do I Re-Initiate A Download App If There Was An Error? 27.
ALL ABOUT Uconnect® ACCESS 165 29. I Am Trading My Vehicle In. Can I Transfer Apps To My New Vehicle If I Have An Active Subscription? No. Privacy Practices WARNING! (Continued) Uconnect® features and applications in this vehicle. Only use Uconnect® when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.
166 ALL ABOUT Uconnect® ACCESS • Ensure the volume level of the system is set to a level • Keep drinks, rain, and other sources of moisture away from your system. Besides damage to your system, that still allows you to hear outside traffic and emermoisture can cause electric shocks as with any elecgency vehicles. tronic device.
ALL ABOUT Uconnect® ACCESS 167 Disc Drive • Do not insert any damaged, warped, scratched or dirty discs into the disc player. • Discs that have been modified with an adhesive label should not be used in the CD/DVD player. • Do not insert more than one disc at a time into the drive slot. FCC Declaration NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
168 ALL ABOUT Uconnect® ACCESS Safety Information Exposure to Radio Frequency Radiation Device Connection And Audio Tips With Uconnect® The radiated output power of the internal wireless radio • More than one phone or device can be paired to your vehicle. The connected device with the highest priority is far below the FCC radio frequency exposure limits. will be used.
ALL ABOUT Uconnect® ACCESS 169 • After all devices are connected/paired, when switch- • All secondary incoming phone calls will be treated ing to a different audio source, audio will auto-play similar to “call waiting” (except 9-1-1 Call). from the new source. • When connecting a second device via USB, that device • Current audio (AM/FM/SAT/AUX) will continue to will have priority and auto play accordingly. A phone play when switching to a non-media type App.
Uconnect® 8.4A CONTENTS 䡵 Uconnect® 8.4A System . . . . . . . . . . . . . . . . . .173 ▫ USB/iPod® Mode . . . . . . . . . . . . . . . . . . . . .188 䡵 Radio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .175 ▫ AUX Mode . . . . . . . . . . . . . . . . . . . . . . . . . .190 ▫ Setting Presets . . . . . . . . . . . . . . . . . . . . . . . .177 ▫ SD Card Mode — If Equipped . . . . . . . . . . . .191 ▫ SiriusXM Satellite Radio Mode . . . . . . . . . . . .178 ▫ Bluetooth® Mode . . . . . . . . .
172 Uconnect® 8.4A ▫ Things You Should Know About Your Uconnect® Phone . . . . . . . . . . . . . . . . . . . . .216 ▫ General Information . . . . . . . . . . . . . . . . . . .223 䡵 Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . .223 ▫ Navigation Registration (Uconnect® 8.4A Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 ▫ Getting Started . . . . . . . . . . . . . . . . . . . . . . .223 ▫ Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . .224 ▫ Where To?. . .
Uconnect® 8.4A 173 Uconnect® 8.4A System 2. Media Touch the Media soft-key to access media sources such as: Disc, USB Device and AUX as long as the requested media is present. 3. Climate Refer to Climate Controls in your vehicles Owner’s Manual for further details. 4. Nav (If Equipped) The Uconnect® 8.4A System is Navigation-ready, see your authorized dealer for details. 5. Phone 1. Radio Touch the Phone soft-key to access the Uconnect® Phone Touch the Radio soft-key to enter the Radio Mode.
174 Uconnect® 8.4A 6. Apps 8. ENTER/BROWSE & TUNE/SCROLL Touch the Apps soft-key to access Smartphone and Press the ENTER/BROWSE button to accept a highlighted selection on the screen. Rotate the TUNE/ Connected vehicle options. SCROLL rotary knob to scroll through a list or tune a 7. Settings radio station. Touch the Settings soft-key to display the list of available 9. BACK settings.
Uconnect® 8.4A 175 • AM The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the Volume control knob clockwise increases the volume, and counter-clockwise decreases it. • FM Tune/Scroll Control • SiriusXM Satellite Radio (if equipped) When the audio system is turned on, the sound will be set at the same volume level as last played.
176 Uconnect® 8.4A Seek And Direct Tune Functions starting station after passing through the entire band two times, the radio will stop at the station where it began. The Seek Up and Down functions are activated by touching the double arrow soft-keys to the right and left Fast Seek Down – Touch and hold the Seek Down of the radio station display, or by pressing the left soft-key to advance the radio through the available Steering Wheel Audio Control (if equipped) up or down.
Uconnect® 8.4A 177 The Radio stores up to 12 presets in each of the Radio You can backspace an entry by touching the bottom left modes. A set of 6 presets are visible at the top of the radio screen. Undo soft key. You can switch between the two radio presets by touchGO ing the “arrow” soft-key located in the upper right of the When touched, the green GO soft key allows the you to radio screen.
178 Uconnect® 8.4A Preset Selection From List SiriusXM Premier A Preset can be selected by touching any of the listed Get over 160 channels on your satellite radio, and enjoy Presets, or by pressing the ENTER/BROWSE button on all you want, all in one place. Hear commercial-free the Tune Knob to select the currently highlighted Preset. music plus sports, news, talk and entertainment.
Uconnect® 8.4A 179 See SiriusXM Customer Agreement for complete terms at www.siriusxm.com. All fees and programming subject to change. Our satellite service is available only to those at least 18 and older in the 48 contiguous USA and D.C. Our Sirius satellite service is also available in PR (with coverage limitations). Our Internet radio service is available throughout our satellite service area and in AK and HI. © 2012 Sirius XM Radio Inc.
180 Uconnect® 8.4A • The Genre is displayed below the Presets Bar. Replay • The SiriusXM Channel Number is displayed in the The replay function provides a means to store and replay up to 22 minutes of music audio and 48 minutes of talk center. radio. Once the channel is switched, content in replay • The Program Information is displayed at the bottom of memory is lost. the Channel Number. Touch the Replay soft-key.
Uconnect® 8.4A 181 Rewind Favorites Touch the RW soft-key to rewind the content in steps of five seconds. Touching the RW soft-key for more than two seconds rewinds the content. The Radio begins playing the content at the point at which the touch is released. Touch the fav. soft-key to activate the favorites menu, which will time out in five seconds in absence of user interaction. Forward The favorites feature enables you to set a favorite artist, or song that is currently playing.
182 Uconnect® 8.4A Fav. Song: While the song is playing to set a Favorite You can scroll the Channel list by touching the up and Song, touch the fav. soft-key and then the Fav Song down arrows, located on the right side of the screen. Scrolling can also be done by operating the Tune/Scroll soft-key. Knob. Browse In SXM Genre Touch the Browse soft-key to edit Presets, Favorites, Game Zone, and Jump settings, along with providing the Touch the Genre soft-key to display a list of Genres.
Uconnect® 8.4A 183 You can scroll the Favorites list by touching the up and down arrows located at the right side of the screen. A Preset can be selected by touching any of the listed Scrolling can also be done by operating the Tune/Scroll Presets, or by pressing the ENTER/BROWSE button on Knob as well. the Tune Knob to select the currently highlighted Preset. When selected, the Radio tunes to the station stored in Remove Favorites the Preset, and returns to the main Radio screen.
184 Uconnect® 8.4A Game Zone Remove Selection Touch the Game Zone soft-key, located at the left of the Touch the Remove Selection tab at the top of the screen. Browse screen. This feature provides you with the ability Touch the Delete All soft-key to delete all of the Selections or to select teams, edit the selection, and set alerts. touch the Trash Can icon next to the Selection to be deleted. On Air Alert Settings Touch the On-Air tab at the top of the screen.
Uconnect® 8.4A 185 Balance/Fade Equalizer 3 Touch the Balance/Fade soft-key to Balance audio be- Touch the Equalizer soft-key to activate the Equalizer tween the front speakers or fade the audio between the screen. rear and front speakers. Touch the + or - soft-keys, or by touching and dragging Touching the Front, Rear, Left, or Right soft-keys or touch over the level bar for each of the equalizer bands.
186 Uconnect® 8.4A Speed Adjusted Volume The Speed Adjusted Volume is adjusted by touching of the + and - buttons or by touching, and dragging over the Level Bar This alters the automatic adjustment of the audio volume with variation to vehicle speed. Volume increases automatically as speed increase to compensate for normal road noise. Surround System (If Equipped) Touch the On soft-key to activate Surround Sound. Touch Off to deactivate this feature.
Uconnect® 8.4A 187 Media Mode Browse Disc Mode — If Equipped Touch the Browse soft-key to display the browse window. The left side of the browse window displays a list of ways you can browse through the contents of the Disc. If supported by the device, you can browse by Folders, Artists, Playlists, Albums, Songs, etc. Touch the desired soft-key on the left side of the screen.
188 Uconnect® 8.4A Repeat Tracks Touch the Tracks soft-key to display a pop up with the Song List. The currently playing song is indicated by an arrow and lines above and below the song title. When in the Tracks List screen you can rotate the TUNE/SCROLL knob to highlight a track (indicated by the line above and Shuffle below the track name) and then press the ENTER/ Touch the Shuffle soft-key to play the selections on the BROWSE knob to start playing that track.
Uconnect® 8.4A 189 Seek Up/Down Source Touch and release the right arrow soft-key for the next selection on the USB device/iPod®. Touch and release the left arrow soft-key to return to the beginning of the current selection, or to return to the beginning of the previous selection if the USB device/iPod® is within the first second of the current selection. Touch the Source soft-key to select the desired audio source: USB/iPod®.
190 Uconnect® 8.4A Info AUX Mode Touch the Info soft-key to display the current track Overview information. Touch the Info soft-key a second time to AUX (Auxiliary Mode) is entered by inserting an AUX cancel this feature. device using a cable with a 3.5 mm audio jack into the AUX port or by touching the AUX soft-key on the left side of the Tracks display. Once in Media Mode, touch the Source soft-key and Touch the Tracks soft-key to display a pop up with the select AUX. Song List.
Uconnect® 8.4A 191 radio; use the device controls instead. Adjust the volume SD Card Mode — If Equipped with the VOLUME & MUTE rotary knob, or with the Overview volume of the attached device. SD Card Mode is entered by either inserting a SD Card NOTE: The vehicle radio unit is acting as the amplifier into the SD Card slot or touch the SD Card soft-key on the for audio output from the Auxiliary device. Therefore if left side of the display.
192 Uconnect® 8.4A Browse Repeat Touch the browse soft-key to display the browse window. The left side of the browse window displays a list of ways you can browse through the contents of the SD Card. If supported by the device, you can browse by Folders, Artists, Playlists, Albums, Songs, etc. Touch the desired soft-key on the left side of the screen. The center of the browse window shows items and it’s sub-functions, which can be scrolled by touching the Up and Down soft-keys to the right.
Uconnect® 8.4A 193 Tracks Bluetooth® Mode Touch the Tracks soft-key to display a pop up with the Song List. The currently playing song is indicated by an arrow and lines above and below the song title. When in the Tracks List screen you can rotate the TUNE/SCROLL knob to highlight a track (indicated by the line above and below the track name) and then press the ENTER/ BROWSE knob to start playing that track.
194 Uconnect® 8.4A To access Bluetooth® mode, touch the Bluetooth® soft- current selection, or return to the beginning of the key on the left side of the display. previous selection if the Bluetooth® device is within the first second of the current selection. Source Touch the Select Source soft-key to select the desired audio source, USB/iPod®, SD Card, AUX or Bluetooth®. This screen will time out after a few seconds and return to the main radio screen if no selection is made.
Uconnect® 8.4A 195 Audio Refer to Radio Mode for adjusting the audio settings. Uconnect® Phone • Hands-free Text Message Reply. (Forward one of 18 pre-defined SMS messages to incoming calls/text messages). • Redialing last dialed numbers (“Redial”). Overview • Calling Back the last incoming call number (“Call Back”). Uconnect® Phone is a voice-activated, hands-free, invehicle communications system.
196 Uconnect® 8.4A Screen Activated Features: • Dialing via Keypad using touchscreen. NOTE: Your phone must be capable of SMS messaging via Bluetooth® for messaging features to work properly. Your mobile phone’s audio is transmitted through your • Viewing and Calling contacts from Phonebooks disvehicle’s audio system; the system will automatically played on the touchscreen. mute your radio when using the Uconnect® Phone.
Uconnect® 8.4A 197 WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in an accident causing serious injury or death. The Uconnect® Phone is driven through your Bluetooth® “Hands-Free Profile” mobile phone.
198 Uconnect® 8.4A The Uconnect® Phone is fully integrated with the vehi- You will be prompted for a specific command and then cle’s audio system. The volume of the Uconnect® Phone guided through the available options. can be adjusted either from the radio volume control • Prior to giving a voice command, one must wait for the knob or from the steering wheel radio control (right beep, which follows the “Listen” prompt or another switch), if so equipped. prompt.
Uconnect® 8.4A 199 works best when you talk in a normal conversational do you want to call?” in the case where a phone call was tone, as if speaking to someone sitting a few feet/ requested but the specific name was not recognized. meters away from you.
200 Uconnect® 8.4A Cancel Command At any prompt, after the beep, you can say “Cancel” and you will be returned to the main menu. or button on your steering You can also press the wheel when the system is listening for a command and be returned to the main or previous menu. Pair (Link) Uconnect® Phone To A Mobile Phone To begin using your Uconnect® Phone, you must pair your compatible Bluetooth® enabled mobile phone.
Uconnect® 8.4A 201 5. When the pairing process has successfully completed, the system will prompt you to choose whether or not 2. If there is no phone currently connected with the this is your favorite phone. Selecting Yes will make system, a pop-up will appear. this phone the highest priority. This phone will take precedence over other paired phones within range. 3. Select Yes to begin the pairing process. Then, search for available devices on your Bluetooth® enabled mobile phone.
202 Uconnect® 8.4A • Search for available devices on your Bluetooth® enabled mobile phone.
Uconnect® 8.4A 203 You can also use the following VR commands to bring up • Uconnect® Phone will display an in process screen while the system is connecting, the Paired Phone screen from any screen on the radio: • “Show Paired Phones” or • “Connect My Phone” Pair A Bluetooth® Streaming Audio Device • Touch the “Media” soft-key to begin, • When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite device.
204 Uconnect® 8.4A Connecting To A Particular Mobile Phone Or Audio Device After Pairing 3. Touch the “+” soft-key located to the right of the device name. Uconnect® Phone will automatically connect to the high- 4. The options pop-up will be displayed. est priority paired phone and/or Audio Device within 5. Touch the “Disconnect Device” soft-key. range. If you need to choose a particular phone or Audio Device follow these steps: 6. Touch the “X” to exit out of the Settings screen. 1.
Uconnect® 8.4A 205 Making A Phone Or Audio Device A Favorite 1. Touch the “Settings” soft-key. Phonebook Download (Automatic Phonebook Transfer From Mobile Phone) — If Equipped If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text 3. Touch the “+” soft-key located to the right of the names) and number entries from the mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access device name. Profile may support this feature.
206 Uconnect® 8.4A • A maximum of 1000 entries per phone will be down- Managing Your Favorites loaded and updated every time a phone is connected There are three ways you can add an entry to your to the Uconnect® Phone. Favorites. • Depending on the maximum number of entries down- 1. During an active call of a number to make a favorite, loaded, there may be a short delay before the latest touch and hold a favorite soft-key on the top of the downloaded names can be used.
Uconnect® 8.4A 207 3. From the Phone main screen, select phonebook. From the phonebook screen, select the “Favorites” soft-key and then select the + soft-key located to the right of the phonebook record. Select an empty entry and touch the + on that selected entry. When the Options pop-up appears, touch “Add from Mobile”. You will then be asked which contact and number to choose from your mobile phonebook. When complete the new favorite will be shown.
208 Uconnect® 8.4A • Mobile Phonebook • Recent Call Log • SMS Message Viewer Dial By Saying A Number 1. Press the button on your steering wheel to begin. 3. The Uconnect® Phone will dial the number associated with John Doe, or if there are multiple numbers it will ask which number you want to call for John Doe. Call Controls The touchscreen allows you to control the following call features: 2. After the “Listening” prompt and the following beep, • say “Dial 151–1234–5555.” • 3.
Uconnect® 8.4A 209 Touch-Tone Number Entry Recent Calls 1. Touch the “Phone” soft-key. You may browse up to 34 of the most recent of each of the following call types: 2. Touch the “Dial” soft-key. 3. The Touch-Tone screen will be displayed. • Incoming Calls • Outgoing Calls 4. Use the numbered soft-keys to enter the number and • Missed Calls touch “Call.
210 Uconnect® 8.4A NOTE: The Uconnect® Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can When you receive a call on your mobile phone, the only answer an incoming call or ignore it. Uconnect® Phone will interrupt the vehicle audio sysbutton on your steering wheel to accept Making A Second Call While Current Call Is In tem. Press the the call.
Uconnect® 8.4A 211 Toggling Between Calls Redial If two calls are in progress (one active and one on hold), Touch the “Redial” soft-key, or press the and after the touch the “Swap” soft-key on the Phone main screen. “Listening” prompt and the following beep, say “ReOnly one call can be placed on hold at a time. dial.” button on the steering wheel to The Uconnect® Phone will call the last number that was You can also press the toggle between the active and held phone call. dialed from your mobile phone.
212 Uconnect® 8.4A Uconnect® Phone Features Voice Mail Calling Roadside Assistance / Towing Assistance To learn how to access your voice mail, refer to “Working with Automated Systems”. If you need roadside/towing assistance: 1. Press the button on the steering wheel to begin. Working With Automated Systems This method is used in instances where one generally has 2.
Uconnect® 8.4A 213 touchscreen or press the button on the steering wheel and say the word “Send” then the sequence you wish to enter. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can press the button on the steering wheel and say, “Send 3 7 4 6 #.” Saying “Send” followed by a number, or sequence of numbers, is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager.
214 Uconnect® 8.4A 3. Select either “Brief” or “Detailed” by touching the box next to the selection. A check-mark will appear to The button on the steering wheel can be used when indicate your selection. you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is Phone And Network Status Indicators asking “There are two numbers with the name John.
Uconnect® 8.4A 215 Dialing Using The Mobile Phone Keypad WARNING! Driving while distracted can result in loss of vehicle control, accident and injury. Chrysler Group LLC strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road or your hands off the steering wheel. Your primary responsibility is the safe operation of your vehicle.
216 Uconnect® 8.4A Mute/Un-Mute (Mute ON/OFF) Connect Or Disconnect Link Between The When you mute the Uconnect® Phone, you will still be Uconnect® Phone And Mobile Phone able to hear the conversation coming from the other If you would like to connect or disconnect the Bluetooth® party, but the other party will not be able to hear you.
Uconnect® 8.4A 217 • Speak normally, without pausing, just as you would Even though the system is designed for many languages speak to a person sitting a few feet/meters away from and accents, the system may not always work for some. When navigating through an automated system such as you. voice mail, or when sending a page, before speaking the • Ensure that no one other than you is speaking during digit string, make sure to say “Send.” a voice command period.
218 Uconnect® 8.4A Far End Audio Performance Audio quality is maximized under: • Low-To-Medium Blower Setting • Low-To-Medium Vehicle Speed • Low Road Noise • Smooth Road Surface • Fully Closed Windows • Dry Weather Conditions • Operation From The Driver’s Seat In a convertible vehicle, system performance may be compromised with the convertible top down.
Uconnect® 8.4A 219 Here’s how: Press the “Uconnect® Phone” button and wait for the beep, then say “reply.” Uconnect® will give the following prompt: “Please say the message you would like to send.” Wait for the beep and say one of the pre-defined messages. (If you are not sure, you can say “help”). Uconnect® will then read the pre-defined messages allowed. As soon as you hear the message you “Yes.” “No.” “Call me.” “Okay.” “I’ll call you later.” “I can’t talk right now.
220 Uconnect® 8.4A Voice Texting (U.S. Residents Only) WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on the safe operation of the vehicle. Failure to do so may result in an accident causing serious injury or death. Voice Texting Voice Texting allows you to compose a new text or reply to an incoming text message.
Uconnect® 8.4A 221 7. Wait for the beep, and then dictate any message up to 140 characters. If you exceed 140 characters, you will Press the Uconnect® Phone button on the steering hear the following prompt: “Message was too long; wheel, your message will be truncated.” Wait for the beep, 8. Uconnect® will then repeat the message back to you. Say “Text.” 9.
222 Uconnect® 8.
Uconnect® 8.4A 223 General Information Navigation This device complies with Part 15 of the FCC rules and Navigation Registration (Uconnect® 8.4A Only) RSS 210 of Industry Canada. Operation is subject to the Uconnect® 8.4A is a Navigation-capable for dealer actifollowing conditions: vation.
224 Uconnect® 8.4A Main Menu • Touch Information to view Traffic, Where Am I? and Trip Computer information. • Touch Emergency to search for Hospitals, Police and Fire Stations near your current location. You can also display your current location and save any Emergency facility location to your Favorites. • Touch Stop to stop a route. • Touch Detour to detour a route. • Touch Where To? to find or route to a destination. • Touch View Map to view the map.
Uconnect® 8.4A 225 Where To? From the Nav Main Menu, touch the Where To? soft-key and select one of the following methods to program a route guidance. 3 NOTE: Refer to the individual section of the chosen option for further information. Address Touch this soft-key to search by a street address or a street name with house number.
226 Uconnect® 8.4A Recent Go Home Touch this soft-key to access previously routed addresses Touch this soft-key to program or confirm a route to the or locations. saved home address. Point of Interest Trips Touch this soft-key when you want to route to a point of Touch this soft-key to program a new trip or recall a interest. The Point of Interest database allows you to saved trip. select a destination from a list of locations and public GEO Coordinates places, or points of interest (POI).
Uconnect® 8.4A 227 Point on Map Closest City Touch this soft-key to select a destination directly from the Map screen. By selecting a street segment or icon, you can quickly enter a destination without the need to input the city name or street. Touch this soft-key to route to a nearby city. The screen will display an alphabetical listing of nearby cities. The navigation system will calculate a route with the destination at the center of the nearby city.
228 Uconnect® 8.4A Where To? — Address To enter a destination by Address, follow these steps: 1. While in the Nav Main Menu, touch the Where To? soft-key and then touch the Address soft-key. NOTE: To change the state and/or country, touch the state, country soft-key and follow the prompts to change the state and/or country.
Uconnect® 8.4A 229 2. Touch Spell City or Spell Street to begin entering the address of your destination. If you touch Spell City, you will have to enter and select/touch the desired city name, followed by the desired street name and lastly the house number. 3 If you touch Spell Street, you will have to enter and select/touch the desired street name in the correct city and then you will have to enter the house number 3.
230 Uconnect® 8.4A You can touch the back arrow soft-key to return to the Touch the soft-key with the name of the desired destination. Confirm the route with Yes to start the route previous screen or the X soft-key to exit. guidance. Where To? — Recent To route to a recent destination, touch the Recent soft-key To delete a destination from the list, touch the trash can icon soft-key. in the NAV Main Menu. To display the options for a destination touch the Options soft-key that looks like a gear.
Uconnect® 8.4A 231 The following Options are available for each destination: • Edit Name • Add Phone Number • Move Up in the list • Move Down in the list • Place Pin on the location (saves the spot on the list) NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
232 Uconnect® 8.4A • All POIs • Around Me • Spell POI Name • In a City You can also change your POI search area, by touching • Near Destination (only available during route guidance) the Change Search Area soft-key. You will have the • Along Route (only available during route guidance) following options to change your search area: NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4A 233 • Type • ABC (Search) Touch the desired Gas Station and touch Yes to confirm the destination. NOTE: If you are currently on a route guidance and you select a gas station, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination You can search for a gas station by the following catego- • Add as last destination ries, which are soft-key tabs at the top of the screen.
234 Uconnect® 8.4A NOTE: If you are currently on a route guidance and you select a Restaurant, the system will ask you to choose one To select a Restaurant POI, touch Point of Interest from the Nav Main Menu, then touch the Point of Interest of the following: soft-key and then touch the Restaurants soft-key. • Cancel previous route POI — Restaurants You can search for a restaurants by the following categories, which are soft-key tabs at the top of the screen.
Uconnect® 8.4A 235 You can search for a hotel or motel by the following You can touch the back arrow soft-key to return to the categories, which are soft-key tabs at the top of the previous screen or the X soft-key to exit. screen. POI — ATM/Banking • Name To select an ATM or Bank POI, touch Point of Interest from the Nav Main Menu, then touch the Point of Interest • Distance soft-key and then touch the ATM/Banking soft-key.
236 Uconnect® 8.4A Touch the desired ATM or Bank and touch Yes to confirm All POIs the destination. NOTE: If you are currently on a route guidance and you select an ATM or Bank POI, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4A 237 The available categories are: • Parking • ATM/Banking • Recreation • Automotive • Restaurants • Coffee Shops • Shopping • Community • Travel • Entertainment • Truck • Gas Stations Select a category and then select a subcategory if necessary. Touch the ABC soft-key to activate a keyboard with Alphabetic characters in order to search within the POI categories.
238 Uconnect® 8.4A NOTE: If you are currently on a route guidance and you A keyboard will appear on the screen. Type in the POI select a POI, the system will ask you to choose one of the that you want to search and touch the List soft-key to following: display available items. • Cancel previous route • Add as first destination Touch the desired POI and touch Yes to confirm the destination.
Uconnect® 8.4A 239 To delete a destination from the list, touch the trash can To route to a favorite destination, touch the Favorites icon soft-key. soft-key in the NAV Main Menu. To save a favorite destination, touch the Add Favorite soft-key and follow the steps to route a destination. Touch the soft-key with the name of the desired favorite destination and confirm the route with Yes to start the To display the options for a favorite destination touch the route guidance.
240 Uconnect® 8.4A NOTE: If you are currently on a route guidance and you select a Favorite, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. Where To? — Intersection To enter a destination by Intersection, follow these steps: This menu shows the default country and state setting. 1.
Uconnect® 8.4A 241 If you touch Spell Street, you will have to enter and select/touch the desired street name in the correct city and then you will have to enter the intersecting street. 3. Once the correct City and Intersection has been entered, you will be asked to confirm your destination. 4. Touch the Yes soft-key to confirm your destination and begin your route. NOTE: If you are currently on a route guidance and you select a Intersection, the system will ask you to choose one of the following: 2.
242 Uconnect® 8.4A Where To? — Go Home To enter your Home Address, follow these steps: • City Center • Closest Cities • Phone Number 1. While in the Nav Main Menu, touch the Where To? soft-key and then touch the Go Home soft-key. If there NOTE: Refer to the individual section of the chosen is no Home Address entered, touch Yes to enter it now. option for further information. 2. To set your set your Home Address choose one of the 3. Once you have generated your Home Address, you will be asked to Save it.
Uconnect® 8.4A 243 Change/Delete Your Home Address Where To? — Trips To change or delete your current Home Address perform the following: 1. Touch the Go Home soft-key in the Where To? Menu 2. Touch the Options soft-key at the bottom of the displayed map. 3. Touch Clear Home and then touch Yes to clear/delete your Home Address. 4. To enter in a new Home Address, follow the Where To? – Go Home procedure.
244 Uconnect® 8.4A Touch the soft-key with the name of the desired Trip and 3. Touch Add Destination to add destinations to your touch the first destination in the list. Confirm the route by trip. touching Yes to start the route guidance. 4. Choose from the following options to add a destination: • Address • Recent • Point of Interest • Favorites • Intersection • GEO Coordinates • Point on Map • City Center • Closest Cities To add a Trip, follow these steps: • Phone Number 1.
Uconnect® 8.4A 245 5. Add more needed destinations to your trip. Where To? — GEO Coordinate NOTE: Each destination will be listed in order, with the To enter a destination by GEO Coordinate, touch Where To? in the Nav Main Menu and then touch the GEO last destination being the final destination. Coordinate soft-key. 6. Your new Trip will appear on the Trips list. To delete a Trip from the list, touch the trash can icon soft-key.
246 Uconnect® 8.4A 2. Touch the OK soft-key. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. 3. Enter the Longitude by typing in the numbers. Use the left and right arrows to select specific numbers in the Where To? — Point on Map location shown. To enter a destination by Point on Map, touch Where To? NOTE: Touch the Format soft-key to change the format in the Nav Main Menu and then touch the Point on Map soft-key. of the Latitude/Longitude entry. 4.
Uconnect® 8.4A 247 1. Use the touchscreen to drag the center of the cross Where To? — City Center over the desired destination. To enter a destination by City Center, touch Where To? in 2. Either touch the address bar at the top center of the the Nav Main Menu and then touch the City Center screen to confirm your location or touch the Details soft-key. soft-key in the upper right corner to display the available locations near that point on the map. 3.
248 Uconnect® 8.4A 3. Touch the Yes soft-key to confirm your destination and begin your route. NOTE: If you are currently on a route guidance and you select a City Center, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4A 249 NOTE: If you are currently on a route guidance and you Where To? — Phone Number select a Closest City, the system will ask you to choose To enter a destination by Phone number, touch Where To? one of the following: in the Nav Main Menu and then touch the Phone Number soft-key. • Cancel previous route • Add as first destination 3 • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
250 Uconnect® 8.4A 2. Touch the desired destination from the list. 3. Touch the Yes soft-key to confirm your destination and begin your route. NOTE: If you are currently on a route guidance and you select a Phone number destination, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4A 251 NOTE: Since toll roads, tunnels and ferries are built for the purpose of shortening travel distances, avoiding these road types may increase distance and travel time. • Save – Touch the Save soft-key to save the destination as a Favorite. Touch the Yes soft-key to confirm your destination and to start your route guidance. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
252 Uconnect® 8.4A View Map Menu Touch this soft-key to return to the Nav Main Menu. Zoom In +/ Zoom Out – Touch the Zoom In (+) or Zoom Out (–) soft-keys to change the zoom level. Roads with lower functional classification are not shown in higher zoom levels. (E.g. residential streets, lightly-traveled county roads.) Time of Arrival/Time to Destination/Distance (only during route guidance) Touch the soft-key in the upper right area of the screen to the display items available.
Uconnect® 8.4A 253 Turn List (only during route guidance) Settings Touch the area in the upper center part of the screen that Touch this soft-key to view all the available settings. See displays your next turn to see a Turn List for your current View Map – Settings for more information. route. Touch a turn in the displayed Turn List for the Repeat following options: Touch this soft-key to repeat the current voice prompt.
254 Uconnect® 8.4A Stop Guidance View Map — Settings Touch this soft-key to stop route guidance. Where Am I? displays the address and GEO Coordinates of your current location. • Touch the GPS soft-key to view the GPS information. • Touch the Save soft-key to save the location in your Favorites. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. With the Map displayed, touch the Options soft-key and then touch the Settings soft-key.
Uconnect® 8.4A 255 The following Map Settings are available: Units Map Setup Touch this soft-key to change the units display. Touch the desired soft-key. Touch this soft-key to display items to customize how your map is viewed. Settings – Map Setup for more • U.S. (mile/feet) information. • Imperial (mile/yard) Speed Limit • Metric (meter) Touch this soft-key to turn on/off speed limit warning announcements and to enter a pre-defined speed limit for GPS your route.
256 Uconnect® 8.4A Copy device information to USB? (If Equipped) Current Street Touch this soft-key to copy your radio information to a Touch this soft-key to turn on/off the current street USB jump drive through the available USB port. display on the lower center of the Map View. Touch and release the soft-key until a check-mark appears, showing Settings — Map Setup the setting has been selected.
Uconnect® 8.4A 257 AutoZoom Show POI Icons Touch this soft-key to change how the AutoZoom feature Touch this soft-key to show the selected Point of Interest adjust the zoom level during guidance in Map View. icons while in Map View. Touch and release the soft-key Touch the desired soft-key. until a check-mark appears, showing the setting has been selected. • Far POI Icon List • Normal Touch this soft-key to display the available Point of • Near Interest icons you would like displayed while in Map View.
258 Uconnect® 8.4A Park Areas You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. Touch this soft-key to display Park Areas while in Map View. Touch and release the soft-key until a check-mark Settings — Guidance appears, showing the setting has been selected. With the Map displayed, touch the Options soft-key, then touch the Settings soft-key and then the Guidance softRailroads key.
Uconnect® 8.4A 259 Nav Volume Adjustment Navigation Turn-by-Turn Displayed in Cluster Touch the (+) or (-) soft-key to adjust the Nav Voice Touch this soft-key to enable navigation turn-by-turn Prompt Volume. displayed in vehicles cluster during route guidance. Touch and release the soft-key until a check-mark apLane Recommendation pears, showing the setting has been selected. Touch this soft-key to enable Lane Recommendation TMC Route Mode — If Equipped during route guidance.
260 Uconnect® 8.4A TMC Avoidance Types — If Equipped Information Touch this soft-key to display the available Traffic Message Channel (TMC) Avoidance Types you would like displayed while in route guidance. Touch and release the desired selection soft-key until a check-mark appears, showing the setting has been selected. Avoid Touch the Avoid button on the touchscreen to choose road types to avoid during your route. To make a selection touch and release the desired setting until a check-mark appears.
Uconnect® 8.4A 261 NOTE: You can touch the back arrow soft-key to return Where Am I? displays the address and GEO Coordinates of your current location. to the previous screen or the X soft-key to exit. Information — Where Am I? • Touch the GPS soft-key to view the GPS information. • Touch the Save soft-key to save the location in your Favorites. NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
262 Uconnect® 8.4A Information — Trip Computer Trip Computer displays the following trip information from your last trip • Travel Direction • Distance to final Destination • Vehicle Speed • Distance Traveled • Overall average speed • Moving average speed • Maximum speed reached • Total time traveled To select Trip Computer information, touch the Information soft-key from the Nav Main Menu and then touch • Travel time spent moving the Trip Computer soft-key.
Uconnect® 8.4A 263 Emergency From the Nav Main Menu, touch the Emergency soft-key and touch one of the following options to search and route to a specific location. • Hospital – Search and route to a Hospital close to your current location • Police – Search and route to a Police Station close to your current location • Fire Department – Search and route a Fire Department close to your current location Touch the Location soft-key to display your exact current location.
264 Uconnect® 8.4A Emergency — Hospital You can search for a Hospital by the following categories, which are soft-key tabs at the top of the screen: • Name • Distance • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. Touch the desired Hospital and touch Yes to confirm the destination.
Uconnect® 8.4A 265 You can touch the back arrow soft-key to return to the You can search for a Police Station by the following categoprevious screen or the X soft-key to exit. ries, which are soft-key tabs at the top of the screen. Emergency — Police • Name • Distance • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. Touch the desired Police Station and touch Yes to confirm the destination.
266 Uconnect® 8.4A You can touch the back arrow soft-key to return to the You can search for a Fire Department by the following previous screen or the X soft-key to exit. categories, which are soft-key tabs at the top of the screen. Emergency — Fire Department • Name • Distance • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. Touch the desired Fire Department and touch Yes to confirm the destination.
Uconnect® 8.4A 267 You can touch the back arrow soft-key to return to the In order to provide Uconnect® Services to you, we may record and monitor your conversations with Roadside previous screen or the X soft-key to exit.
268 Uconnect® 8.4A 9–1–1 Call Operating Instructions 1. Press the 9-1-1 Call button on the Rearview Mirror; NOTE: In case the 9-1-1 Call button is pushed in error, there will be a 10 second delay before the 9-1-1 Call system initiates a call to a 9-1-1 operator. To cancel the 9-1-1 Call connection, press the 9-1-1 Call button on the Rearview Mirror or press the cancellation button on the Phone Screen. Termination of the 9-1-1 Call will turn the green LED light on the Rearview Mirror off. 4.
Uconnect® 8.4A 269 6. If a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit certain vehicle information to a 9-1-1 operator, including the last known GPS coordinates of your vehicle. If a connection is made between a 9-1-1 operator and your vehicle, you understand and agree that 9-1-1 operators may record conversations and sounds in your car upon connection and consent to such recordings.
270 Uconnect® 8.4A 9-1-1 Call System Limitations Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system capabilities. 9-1-1 or other emergency line operators in Canada and Mexico may not answer or respond to 9-1-1 system calls. If the 9-1-1 Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: • The Rearview Mirror light will continuously be illuminated red.
Uconnect® 8.4A 271 Even if the 9-1-1 Call system is fully functional, factors • Equipment malfunction at the 9-1-1 operator facility. beyond Chrysler Group LLC’s control may prevent or • Operator error by the 9-1-1 operator. stop 9-1-1 Call system operation. These include, but are not limited to, the following factors: • Wireless network congestion. • The ignition key has been removed from the ignition • Weather. and the delayed accessories mode is active.
272 Uconnect® 8.4A WARNING! Failure to perform scheduled maintenance and regularly inspect your vehicle may result in vehicle damage and/or serious injury. General Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Uconnect® 8.4AN CONTENTS 䡵 Uconnect® 8.4AN System . . . . . . . . . . . . . . . . .275 䡵 Media Mode . . . . . . . . . . . . . . . . . . . . . . . . . .290 䡵 Radio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .277 ▫ Disc Mode — If Equipped . . . . . . . . . . . . . . .290 ▫ Setting Presets . . . . . . . . . . . . . . . . . . . . . . . .279 ▫ USB/iPod® Mode . . . . . . . . . . . . . . . . . . . . .291 ▫ SiriusXM Satellite Radio Mode — If Equipped. . . . . . . . . . . . . . . . . . . . . . . .
274 Uconnect® 8.4AN ▫ Advanced Phone Connectivity . . . . . . . . . . . .314 ▫ View Map — Settings. . . . . . . . . . . . . . . . . . .359 ▫ Things You Should Know About Your Uconnect® Phone . . . . . . . . . . . . . . . . . . . . .315 ▫ Information. . . . . . . . . . . . . . . . . . . . . . . . . .366 ▫ General Information . . . . . . . . . . . . . . . . . . .321 䡵 Uconnect® Voice Command . . . . . . . . . . . . . . .321 ▫ Emergency . . . . . . . . . . . . . . . . . . . . . . . . . .
Uconnect® 8.4AN 275 Uconnect® 8.4AN System 2. Media Touch the Media soft-key to access media sources such as: Disc, USB Device and AUX as long as the requested media is present. 3. Climate Refer to Climate Controls in your vehicles Owner’s Manual for further details. 4. Nav Touch the Nav soft-key to access the Navigation feature. Refer to the Navigation section in this manual for further details. 1. Radio 5. Phone Touch the Radio soft-key to enter the Radio Mode.
276 Uconnect® 8.4AN 6. Apps 8. ENTER/BROWSE & TUNE/SCROLL Touch the Apps soft-key to access Smartphone and Press the ENTER/BROWSE button to accept a highlighted selection on the screen. Rotate the TUNE/ Connected vehicle options. SCROLL rotary knob to scroll through a list or tune a 7. Settings radio station. Touch the Settings soft-key to display the list of available 9. BACK settings.
Uconnect® 8.4AN 277 • AM The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the Volume control knob clockwise increases the volume, and counter-clockwise decreases it. • FM Tune/Scroll Control • SiriusXM Satellite Radio (if equipped) When the audio system is turned on, the sound will be set at the same volume level as last played.
278 Uconnect® 8.4AN Fast Seek Up – Touch and hold the Seek Up soft-key to advance the radio through the available stations or HD Radio technology (available on Uconnect 8.4AN) channels at a faster rate, the radio stops at the next works similar to conventional radio except it allows available station or channel when the soft-key is released. broadcasters to transmit a high-quality digital signal.
Uconnect® 8.4AN 279 Direct Tune The selected Station or Channel number is displayed in the Direct Tune text box. Press the Tune soft-key located at the bottom of the radio screen. The Direct Tune soft-key screen is available in Setting Presets AM, FM, and SXM radio modes and can be used to direct The Presets are available for all Radio Modes, and are tune the radio to a desired station or channel.
280 Uconnect® 8.4AN Browse In AM/FM Deleting Presets When in either AM or FM, the Browse Screen provides a A Preset can be deleted in the Presets Browse screen by means to edit the Presets List and is entered by touching touching the Trash Can Icon for the corresponding Preset. the Enter/Browse button.
Uconnect® 8.4AN 281 www.siriusxm.com. All fees and programming subject to change. Our satellite service is available only to those at least 18 and older in the 48 contiguous USA and D.C. Our Sirius satellite service is also available in PR (with coverage limitations). Our Internet radio service is available throughout our satellite service area and in AK and HI. © 2012 Sirius XM Radio Inc.
282 Uconnect® 8.4AN No Subscription • The Genre is displayed below the Presets Bar. Radios equipped with a Satellite receiver, require a • The SiriusXM Channel Number is displayed in the subscription to the SiriusXM Service. When the Radio center. does not have the necessary subscription, the Radio is • The Program Information is displayed at the bottom of able to receive the Traffic/Weather channel only. the Channel Number.
Uconnect® 8.4AN 283 Replay Rewind The replay function provides a means to store and replay up to 22 minutes of music audio and 48 minutes of talk radio. Once the channel is switched, content in replay memory is lost. Touch the RW soft-key to rewind the content in steps of five seconds. Touching the RW soft-key for more than two seconds rewinds the content. The Radio begins playing the content at the point at which the touch is released. Touch the Replay soft-key.
284 Uconnect® 8.4AN Fav. Song: While the song is playing to set a Favorite Song, touch the fav. soft-key and then the Fav Song Touch the fav. soft-key to activate the favorites menu, soft-key. which will time out in five seconds in absence of user interaction. Traffic & Weather Favorites You can exit the Favorites Menu by a touch of the “X” in Touch the Traffic & Weather soft-key to tune to a Sirithe top right corner. usXM Traffic and Weather channel.
Uconnect® 8.4AN 285 Browse In SXM Genre Touch the Browse soft-key to edit Presets, Favorites, Touch the Genre soft-key to display a list of Genres. You Game Zone, and Jump settings, along with providing the can select any desired Genre by touching the Genre list, at SiriusXM Channel List. which point, the Radio tunes to a channel with the This Screen contains many sub menus. You can exit a sub content in the selected Genre. menu to return to a parent menu by touching the Back Presets Arrow.
286 Uconnect® 8.4AN When selected, the Radio tunes to the station stored in Remove Favorites the Preset, and returns to the main Radio screen. Touch the Remove Favorites tab at the top of the screen. Touch the Delete All soft-key to delete all of the Favorites Deleting A Preset or touch the Trash Can icon next to the Favorite to be A Preset can be deleted in the Presets Browse screen by deleted. touching the Trash Can icon for the corresponding Preset.
Uconnect® 8.4AN 287 On Air Alert Settings Touch the On-Air tab at the top of the screen. The On-Air list provides a list of Channels currently airing any of the items in the Selections list, and touching any of the items in the list tunes the radio to that channel. Touch the Alert Setting tab at the top of the screen.
288 Uconnect® 8.4AN Balance/Fade Equalizer Touch the Balance/Fade soft-key to Balance audio be- Touch the Equalizer soft-key to activate the Equalizer tween the front speakers or fade the audio between the screen. rear and front speakers. Touch the + or - soft-keys, or by touching and dragging Touching the Front, Rear, Left, or Right soft-keys or touch over the level bar for each of the equalizer bands. The and drag the Speaker Icon to adjust the Balance/Fade.
Uconnect® 8.4AN 289 Speed Adjusted Volume The Speed Adjusted Volume is adjusted by touching of the + and - buttons or by touching, and dragging over the Level Bar This alters the automatic adjustment of the audio volume with variation to vehicle speed. Volume increases automatically as speed increase to compensate for normal road noise. Surround System (If Equipped) Touch the On soft-key to activate Surround Sound. Touch Off to deactivate this feature.
290 Uconnect® 8.4AN Media Mode Browse Disc Mode — If Equipped Touch the Browse soft-key to display the browse window. The left side of the browse window displays a list of ways you can browse through the contents of the Disc. If supported by the device, you can browse by Folders, Artists, Playlists, Albums, Songs, etc. Touch the desired soft-key on the left side of the screen.
Uconnect® 8.4AN 291 Repeat Tracks Touch the Tracks soft-key to display a pop up with the Song List. The currently playing song is indicated by an arrow and lines above and below the song title. When in the Tracks List screen you can rotate the TUNE/SCROLL knob to highlight a track (indicated by the line above and Shuffle below the track name) and then press the ENTER/ Touch the Shuffle soft-key to play the selections on the BROWSE knob to start playing that track.
292 Uconnect® 8.4AN Seek Up/Down Source Touch and release the right arrow soft-key for the next selection on the USB device/iPod®. Touch and release the left arrow soft-key to return to the beginning of the current selection, or to return to the beginning of the previous selection if the USB device/iPod® is within the first second of the current selection. Touch the Source soft-key to select the desired audio source: USB/iPod®.
Uconnect® 8.4AN 293 Info AUX Mode Touch the Info soft-key to display the current track Overview information. Touch the Info soft-key a second time to AUX (Auxiliary Mode) is entered by inserting an AUX cancel this feature. device using a cable with a 3.5 mm audio jack into the AUX port or by touching the AUX soft-key on the left Tracks side of the display. Once in Media Mode, touch the Touch the Tracks soft-key to display a pop up with the Source soft-key and select AUX. Song List.
294 Uconnect® 8.4AN Controlling The Auxiliary Device SD Card Mode — If Equipped The control of the auxiliary device (e.g., selecting playlists, play, fast forward, etc.) cannot be provided by the radio; use the device controls instead. Adjust the volume with the VOLUME & MUTE rotary knob, or with the volume of the attached device. Overview NOTE: The vehicle radio unit is acting as the amplifier for audio output from the Auxiliary device.
Uconnect® 8.4AN 295 If supported by the device, you can browse by Folders, Artists, Playlists, Albums, Songs, etc. Touch the desired soft-key on the left side of the screen. The center of the browse window shows items and it’s sub-functions, which can be scrolled by touching the Up and Down soft-keys to the right. The Scroll/Tune knob can also be used to scroll. Shuffle Touch the shuffle soft-key to play the selections on the SD Card device in random order to provide an interesting change of pace.
296 Uconnect® 8.4AN Touching the trks soft-key while the pop up is displayed will close the pop up. Audio Refer to Radio Mode for adjusting the audio settings. Bluetooth® Mode Overview Bluetooth® Streaming Audio (BTSA) or Bluetooth® Mode is entered by pairing a Bluetooth® device, containing music, to the Uconnect® System.
Uconnect® 8.4AN 297 Source Uconnect® Phone Touch the Select Source soft-key to select the desired Overview audio source, USB/iPod®, SD Card, AUX or Bluetooth®. Uconnect® Phone is a voice-activated, hands-free, inThis screen will time out after a few seconds and return vehicle communications system. Uconnect® Phone alto the main radio screen if no selection is made. lows you to dial a phone number with your mobile Tracks phone.
298 Uconnect® 8.4AN • Calling Back the last incoming call number (“Call • Viewing and Calling contacts from Recent Call logs. Back”). • Reviewing your recent Incoming SMS. • View Call logs on screen (“Show incoming calls,” • Listen to Music on your Bluetooth® Device via the “Show Outgoing calls,” “Show missed Calls,” “Show touchscreen. Recent Calls”). • Pairing up to 10 phones/audio devices for easy access • Searching Contacts phone number (“Search for John to connect to them quickly. Smith Mobile”).
Uconnect® 8.4AN 299 Uconnect® Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in an accident causing serious injury or death.
300 Uconnect® 8.4AN Uconnect® Voice Command Button button The Uconnect® Voice Command on your steering wheel is only used for “barge in” and when you are already in a call and you want to send Tones or make another call. Operation Voice commands can be used to operate the Uconnect® Phone and to navigate through the Uconnect® Phone menu structure. Voice commands are required after most Uconnect® Phone prompts.
Uconnect® 8.4AN 301 • For certain operations, compound commands can be used. For example, instead of saying “Call” and then “John Smith” and then “mobile”, the following compound command can be said: “Call John Smith mobile.” Natural Speech Your Uconnect® Phone Voice system uses a Natural Language Voice Recognition (VR) engine. Natural speech allows the user to speak commands in phrases or complete sentences.
302 Uconnect® 8.4AN question to which the user can respond without pressing the Pair (Link) Uconnect® Phone To A Mobile Phone button on your steering wheel. “Voice Command” To begin using your Uconnect® Phone, you must pair your compatible Bluetooth® enabled mobile phone. Help Command If you need assistance at any prompt, or if you want to To complete the pairing process, you will need to reference know your options at any prompt, say “Help” following your mobile phone Owner’s Manual.
Uconnect® 8.4AN 303 NOTE: • You must have Bluetooth® enabled on your phone to complete this procedure. • The vehicle must be in PARK. 1. Press the “Phone” soft-key on the screen to begin. 2. If there is no phone currently connected with the system, a pop-up will appear. 3. Select Yes to begin the pairing process. Then, search for available devices on your Bluetooth® enabled mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect® screen.
304 Uconnect® 8.4AN 5. When the pairing process has successfully completed, Pair Additional Mobile Phones the system will prompt you to choose whether or not • Touch the “Settings” soft-key from the Phone main this is your favorite phone. Selecting Yes will make screen, this phone the highest priority. This phone will take • Next, touch the “Phone/Bluetooth®” soft-key, precedence over other paired phones within range.
Uconnect® 8.4AN 305 • Search for available devices on your Bluetooth® en- You can also use the following VR commands to bring up abled mobile phone.
306 Uconnect® 8.4AN • Uconnect® Phone will display an in process screen Connecting To A Particular Mobile Phone Or while the system is connecting, Audio Device After Pairing • When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite device. Selecting Yes will make this device the highest priority. This device will take precedence over other paired devices within range.
Uconnect® 8.4AN 307 3. Touch the “+” soft-key located to the right of the 5. Touch the “Delete Device” soft-key. device name. 6. Touch the “X” to exit out of the Settings screen. 4. The options pop-up will be displayed. Making A Phone Or Audio Device A Favorite 5. Touch the “Disconnect Device” soft-key. 1. Touch the “Settings” soft-key. 6. Touch the “X” to exit out of the Settings screen. 2. Touch the “Phone/Bluetooth®” soft-key. Deleting A Phone Or Audio Device 3.
308 Uconnect® 8.4AN Phonebook Download (Automatic Phonebook Transfer From Mobile Phone) — If Equipped • A maximum of 1000 entries per phone will be downloaded and updated every time a phone is connected to the Uconnect® Phone. If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text • Depending on the maximum number of entries downnames) and number entries from the mobile phone’s loaded, there may be a short delay before the latest phonebook.
Uconnect® 8.4AN 309 Managing Your Favorites There are three ways you can add an entry to your Favorites. 1. During an active call of a number to make a favorite, touch and hold a favorite soft-key on the top of the phone main screen. phonebook record. Select an empty entry and touch the + on that selected entry. When the Options pop-up appears, touch “Add from Mobile”. You will then be asked which contact and number to choose from your mobile phonebook. When complete the new favorite will be shown.
310 Uconnect® 8.4AN Phone Call Features • Mobile Phonebook The following features can be accessed through the Uconnect® Phone if the feature(s) are available and supported by Bluetooth® on your mobile service plan. For example, if your mobile service plan provides threeway calling, this feature can be accessed through the Uconnect® Phone. Check with your mobile service provider for the features that you have.
Uconnect® 8.4AN 311 3. The Uconnect® Phone will dial the number associated Touch-Tone Number Entry with John Doe, or if there are multiple numbers it will 1. Touch the “Phone” soft-key. ask which number you want to call for John Doe. 2. Touch the “Dial” soft-key. Call Controls The touchscreen allows you to control the following call 3. The Touch-Tone screen will be displayed.
312 Uconnect® 8.4AN Recent Calls Answer Or Ignore An Incoming Call — No Call You may browse up to 34 of the most recent of each of the Currently In Progress When you receive a call on your mobile phone, the following call types: Uconnect® Phone will interrupt the vehicle audio sys• Incoming Calls button on your steering wheel to accept tem. Press the the call. You can also touch the “answer” soft-key or • Outgoing Calls touch the caller ID box.
Uconnect® 8.4AN 313 NOTE: The Uconnect® Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Toggling Between Calls Making A Second Call While Current Call Is In Progress button on the steering wheel to You can also press the toggle between the active and held phone call.
314 Uconnect® 8.4AN Redial Advanced Phone Connectivity Touch the “Redial” soft-key, or press the and after the Transfer Call To And From Mobile Phone “Listening” prompt and the following beep, say “ReThe Uconnect® Phone allows ongoing calls to be transdial.” ferred from your mobile phone to the Uconnect® Phone The Uconnect® Phone will call the last number that was without terminating the call. To transfer an ongoing call from your connected mobile phone to the Uconnect® dialed from your mobile phone.
Uconnect® 8.4AN 315 Things You Should Know About Your Uconnect® Phone • Smooth Road Surface • Fully Closed Windows Voice Command • Dry Weather Condition • For best performance, adjust the rearview mirror to Even though the system is designed for many languages provide at least ½ inch (1 cm) gap between the and accents, the system may not always work for some. overhead console (if equipped) and the mirror.
316 Uconnect® 8.4AN Far End Audio Performance Audio quality is maximized under: • Low-To-Medium Blower Setting • Low-To-Medium Vehicle Speed • Low Road Noise • Smooth Road Surface • Fully Closed Windows • Dry Weather Conditions • Operation From The Driver’s Seat In a convertible vehicle, system performance may be compromised with the convertible top down.
Uconnect® 8.4AN 317 Here’s how: Press the “Uconnect® Phone” button and wait for the beep, then say “reply.” Uconnect® will give the following prompt: “Please say the message you would like to send.” Wait for the beep and say one of the pre-defined messages. (If you are not sure, you can say “help”). Uconnect® will then read the pre-defined messages allowed. As soon as you hear the message you “Yes.” “No.” “Call me.” “Okay.” “I’ll call you later.” “I can’t talk right now.
318 Uconnect® 8.4AN Voice Texting (U.S. Residents Only) WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on the safe operation of the vehicle. Failure to do so may result in an accident causing serious injury or death. Voice Texting Voice Texting allows you to compose a new text or reply to an incoming text message.
Uconnect® 8.4AN 319 7. Wait for the beep, and then dictate any message up to 140 characters. If you exceed 140 characters, you will Press the Uconnect® Phone button on the steering hear the following prompt: “Message was too long; wheel, your message will be truncated.” Wait for the beep, 8. Uconnect® will then repeat the message back to you. Say “Text.” 9.
320 Uconnect® 8.
Uconnect® 8.4AN 321 General Information Uconnect® Voice Command This device complies with Part 15 of the FCC rules and Uconnect® 8.4AN Voice Command Quick RSS 210 of Industry Canada. Operation is subject to the Reference following conditions: If the Uconnect® Voice Command button exists on • Changes or modifications not expressly approved by your steering wheel, you have the Voice Command the party responsible for compliance could void the feature, which is optimized for the driver.
322 Uconnect® 8.4AN NOTE: All phone oriented voice commands are acces- • You can interrupt the system prompts at any time by pressing the Uconnect® Voice Command button on the button on the sible by first pressing the Phone Pick Up steering wheel while the system is speaking. After the steering wheel, not the Voice Command button on the beep, you can say a command. steering wheel. To end a call, simply press the Phone button on the steering wheel.
Uconnect® 8.4AN 323 Available Radio Soft-Key Voice Commands Steering Wheel Buttons You can control many of your radio features using your or Phone Pick Up butvoice. Press either the VR ton on your steering wheel.
324 Uconnect® 8.
Uconnect® 8.4AN 325 Voice Command Examples – Uconnect® 8.
326 Uconnect® 8.
Uconnect® 8.4AN 327 Call Initiation (Requires that phone has been Bluetooth® paired with radio Call Management Voice Texting (Requires registration with Uconnect® Access and a current subscription.) NOTE: Requires a compatible mobile device enabled with Bluetooth® Message Access Profile (MAP). iPhone and some other smartphones do not currently support Bluetooth® MAP. Visit www.UconnectPhone.com for system and device compatibility.
328 Uconnect® 8.4AN Voice Text Reply (Radio audibly recognizes these 18 pre-defined SMS messages as you speak) NOTE: Requires a compatible mobile device enabled with Bluetooth Message Access Profile (MAP). iPhone and some other smartphones do not currently support Bluetooth® MAP. Visit www.UconnectPhone.com for system and device compatibility. Forward one of 18 pre-defined SMS messages to incoming calls/text messages: “Yes.” “No.” “Okay.” “I can’t talk right now.” “Call me.” “I’ll call you later.
Uconnect® 8.
330 Uconnect® 8.4AN Navigation • Touch Where To? to find or route to a destination. Getting Started • Touch View Map to view the map. To access the Navigation system, touch the Nav soft-key • Touch Information to view Traffic, Where Am I? and on bottom of the screen. Trip Computer information. Main Menu • Touch Emergency to search for Hospitals, Police and Fire Stations near your current location. You can also display your current location and save any Emergency facility location to your Favorites.
Uconnect® 8.4AN 331 Where To? From the Nav Main Menu, touch the Where To? soft-key and select one of the following methods to program a route guidance. 4 NOTE: Refer to the individual section of the chosen option for further information. Address Touch this soft-key to search by a street address or a street name with house number.
332 Uconnect® 8.4AN Recent Go Home Touch this soft-key to access previously routed addresses Touch this soft-key to program or confirm a route to the or locations. saved home address. Point of Interest Trips Touch this soft-key when you want to route to a point of Touch this soft-key to program a new trip or recall a interest. The Point of Interest database allows you to saved trip. select a destination from a list of locations and public GEO Coordinates places, or points of interest (POI).
Uconnect® 8.4AN 333 City Center Closest City Touch this soft-key to route to a particular city. The Touch this soft-key to route to a nearby city. The screen navigation system will calculate a route with the desti- will display an alphabetical listing of nearby cities. The navigation system will calculate a route with the destination at the center of the city. nation at the center of the nearby city.
334 Uconnect® 8.4AN Where To? — Address To enter a destination by Address, follow these steps: 1. While in the Nav Main Menu, touch the Where To? soft-key and then touch the Address soft-key. NOTE: To change the state and/or country, touch the state, country soft-key and follow the prompts to change the state and/or country.
Uconnect® 8.4AN 335 2. Touch Spell City or Spell Street to begin entering the address of your destination. If you touch Spell City, you will have to enter and select/touch the desired city name, followed by the desired street name and lastly the house number. If you touch Spell Street, you will have to enter and select/touch the desired street name in the correct city and then you will have to enter the house number 4 3.
336 Uconnect® 8.4AN You can touch the back arrow soft-key to return to the Touch the soft-key with the name of the desired destination. Confirm the route with Yes to start the route previous screen or the X soft-key to exit. guidance. Where To? — Recent To route to a recent destination, touch the Recent soft-key To delete a destination from the list, touch the trash can icon soft-key. in the NAV Main Menu. To display the options for a destination touch the Options soft-key that looks like a gear.
Uconnect® 8.4AN 337 The following Options are available for each destination: • Edit Name • Add Phone Number • Move Up in the list • Move Down in the list • Place Pin on the location (saves the spot on the list) NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
338 Uconnect® 8.4AN • All POIs • Around Me • Spell POI Name • In a City You can also change your POI search area, by touching • Near Destination (only available during route guidance) the Change Search Area soft-key. You will have the • Along Route (only available during route guidance) following options to change your search area: NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4AN 339 Touch the desired Gas Station and touch Yes to confirm the destination. NOTE: If you are currently on a route guidance and you select a gas station, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
340 Uconnect® 8.4AN You can search for a restaurants by the following categories, which are soft-key tabs at the top of the screen. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. • Name POI — Hotels/Motels • Distance To select a Hotel or Motel POI, touch Point of Interest from the Nav Main Menu, then touch the Point of Interest soft-key and then touch the Hotels/Motels soft-key.
Uconnect® 8.4AN 341 NOTE: If you are currently on a route guidance and you • Name select a Hotel or Motel, the system will ask you to choose • Distance one of the following: • Type • Cancel previous route • ABC (Search) • Add as first destination Touch the desired ATM or Bank and touch Yes to confirm • Add as last destination the destination. You can touch the back arrow soft-key to return to the NOTE: If you are currently on a route guidance and you previous screen or the X soft-key to exit.
342 Uconnect® 8.4AN All POIs The available categories are: • ATM/Banking • Automotive • Coffee Shops • Community • Entertainment • Gas Stations • Health and Beauty • Highway Exit To select a POI type, touch Point of Interest from the Nav • Hospital Main Menu, then touch the Point of Interest soft-key and • Hotels/Motels then touch All POIs soft-key. You can search through the available POI categories to • Other find your desired POI.
Uconnect® 8.4AN 343 • Recreation • Restaurants • Shopping • Travel • Truck NOTE: If you are currently on a route guidance and you select a POI, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination Select a category and then select a subcategory if necesYou can touch the back arrow soft-key to return to the sary. Touch the ABC soft-key to activate a keyboard with previous screen or the X soft-key to exit.
344 Uconnect® 8.4AN Touch the desired POI and touch Yes to confirm the destination. NOTE: If you are currently on a route guidance and you select a POI, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. Where To? — Favorite Destinations To delete a destination from the list, touch the trash can icon soft-key.
Uconnect® 8.4AN 345 The following Options are available for each favorite Where To? — Intersection destination: To enter a destination by Intersection, follow these steps: • Edit Name 1. While in the Nav Main Menu, touch the Where To? • Add Phone Number soft-key and then touch the Intersection soft-key.
346 Uconnect® 8.4AN NOTE: To change the state and/or country, touch the state, country soft-key and follow the prompts to change the state and/or country. desired street name and lastly you will have to enter the intersection street. If you touch Spell Street, you will have to enter and select/touch the desired street name in the correct city and then you will have to enter the intersecting street. 3. Once the correct City and Intersection has been entered, you will be asked to confirm your destination.
Uconnect® 8.4AN 347 You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. Where To? — Go Home To enter your Home Address, follow these steps: • GEO Coordinates • Point on Map • City Center • Closest Cities • Phone Number 1. While in the Nav Main Menu, touch the Where To? soft-key and then touch the Go Home soft-key. If there NOTE: Refer to the individual section of the chosen is no Home Address entered, touch Yes to enter it now. option for further information.
348 Uconnect® 8.4AN Change/Delete Your Home Address Where To? — Trips To change or delete your current Home Address perform the following: 1. Touch the Go Home soft-key in the Where To? Menu 2. Touch the Options soft-key at the bottom of the displayed map. 3. Touch Clear Home and then touch Yes to clear/delete your Home Address. 4. To enter in a new Home Address, follow the Where To? – Go Home procedure.
Uconnect® 8.4AN 349 To add a Trip, follow these steps: 1. Touch the Create new Trip soft-key. 2. Type in the new Trip Name. 4. Choose from the following options to add a destination: • Address • Recent • Point of Interest • Favorites • Intersection • GEO Coordinates • Point on Map • City Center • Closest Cities • Phone Number NOTE: Refer to the individual section of the chosen option for further information. 3. Touch Add Destination to add destinations to your 5.
350 Uconnect® 8.4AN NOTE: Each destination will be listed in order, with the Where To? — GEO Coordinate last destination being the final destination. To enter a destination by GEO Coordinate, touch Where To? in the Nav Main Menu and then touch the GEO 6. Your new Trip will appear on the Trips list. Coordinate soft-key. To delete a Trip from the list, touch the trash can icon soft-key. To display the options for a trip touch the Options soft-key that looks like a gear.
Uconnect® 8.4AN 351 2. Touch the OK soft-key. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit. 3. Enter the Longitude by typing in the numbers. Use the left and right arrows to select specific numbers in the Where To? — Point on Map location shown. To enter a destination by Point on Map, touch Where To? NOTE: Touch the Format soft-key to change the format in the Nav Main Menu and then touch the Point on Map soft-key. of the Latitude/Longitude entry. 4.
352 Uconnect® 8.4AN 1. Use the touchscreen to drag the center of the cross Where To? — City Center over the desired destination. To enter a destination by City Center, touch Where To? in 2. Either touch the address bar at the top center of the the Nav Main Menu and then touch the City Center screen to confirm your location or touch the Details soft-key. soft-key in the upper right corner to display the available locations near that point on the map. 3.
Uconnect® 8.4AN 353 3. Touch the Yes soft-key to confirm your destination and begin your route. NOTE: If you are currently on a route guidance and you select a City Center, the system will ask you to choose one of the following: • Cancel previous route 4 • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
354 Uconnect® 8.4AN NOTE: If you are currently on a route guidance and you Where To? — Phone Number select a Closest City, the system will ask you to choose To enter a destination by Phone number, touch Where To? one of the following: in the Nav Main Menu and then touch the Phone Number soft-key. • Cancel previous route • Add as first destination • Add as last destination You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4AN 355 2. Touch the desired destination from the list. 3. Touch the Yes soft-key to confirm your destination and begin your route.
356 Uconnect® 8.4AN NOTE: Since toll roads, tunnels and ferries are built for the purpose of shortening travel distances, avoiding these road types may increase distance and travel time. • Save – Touch the Save soft-key to save the destination as a Favorite. Touch the Yes soft-key to confirm your destination and to start your route guidance. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
Uconnect® 8.4AN 357 View Map Menu Touch this soft-key to return to the Nav Main Menu. Zoom In +/ Zoom Out – Touch the Zoom In (+) or Zoom Out (–) soft-keys to change the zoom level. Roads with lower functional classification are not shown in higher zoom levels. (E.g. residential streets, lightly-traveled county roads.) Time of Arrival/Time to Destination/Distance (only during route guidance) Touch the soft-key in the upper right area of the screen to the display items available.
358 Uconnect® 8.4AN Turn List (only during route guidance) Settings Touch the area in the upper center part of the screen that Touch this soft-key to view all the available settings. See displays your next turn to see a Turn List for your current View Map – Settings for more information. route. Touch a turn in the displayed Turn List for the Repeat following options: Touch this soft-key to repeat the current voice prompt.
Uconnect® 8.4AN 359 Where Am I? View Map — Settings Touch the area in the lower center part of the screen that displays your current location to view the Where Am I? view. Where Am I? displays the address and GEO Coordinates of your current location. • Touch the GPS soft-key to view the GPS information. 4 • Touch the Save soft-key to save the location in your Favorites. You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
360 Uconnect® 8.4AN The following Map Settings are available: Guidance Press this button on the touchscreen to display items to customize your route guidance. For more information, go Press this button on the touchscreen to display items to customize how your map is viewed. Settings – Map to Settings - Guidance section of this manual. Setup for more information. GPS Map Setup Press this button on the touchscreen to change the GPS Press this button on the touchscreen to turn on/off speed display.
Uconnect® 8.4AN 361 Settings — Map Setup Map View Touch this soft-key to change how the Map View is displayed. Touch the desired soft-key. 3D Map View is only available on Uconnect 8.4AN. Must select 3D City Models or 3D Landmarks for 3D Map View to display. • 3D • 2D Orientation Touch this soft-key to change how the Map Orientation is displayed. Touch the desired soft-key.
362 Uconnect® 8.4AN Current Street AutoZoom Touch this soft-key to turn on/off the current street Touch this soft-key to change how the AutoZoom feature display on the lower center of the Map View. Touch and adjust the zoom level during guidance in Map View. release the soft-key until a check-mark appears, showing Touch the desired soft-key. the setting has been selected.
Uconnect® 8.4AN 363 Show POI Icons Speed and Flow Touch this soft-key to show the selected Point of Interest icons while in Map View. Touch and release the soft-key until a check-mark appears, showing the setting has been selected. Touch this soft-key to show the Speed and Flow of SiriusXM Traffic while in Map View. Touch and release the soft-key until a check-mark appears, showing the setting has been selected. POI Icon List 3D City Models — Available On Uconnect 8.
364 Uconnect® 8.4AN Digital Terrain Model — Available On Uconnect 8.4AN River Names Touch this soft-key to display the areas terrain while in Touch this soft-key to display River Names while in Map Map View. Touch and release the soft-key until a check- View. Touch and release the soft-key until a check-mark mark appears, showing the setting has been selected. appears, showing the setting has been selected.
Uconnect® 8.4AN 365 The following Guidance options are available: Junction View Touch this soft-key to enable Junction View during route guidance. Touch and release the soft-key until a checkTouch this soft-key to enable Voice Guidance Prompts mark appears, showing the setting has been selected. during route guidance. Touch and release the soft-key until a check-mark appears, showing the setting has been Navigation Turn-by-Turn Displayed in Cluster selected.
366 Uconnect® 8.4AN • Manual Information • Off TMC Avoidance Types — If Equipped Touch this soft-key to display the available Traffic Message Channel (TMC) Avoidance Types you would like displayed while in route guidance. Touch and release the desired selection soft-key until a check-mark appears, showing the setting has been selected. Avoid Touch the Avoid button on the touchscreen to choose road types to avoid during your route.
Uconnect® 8.4AN 367 NOTE: You can touch the back arrow soft-key to return Where Am I? displays the address and GEO Coordinates of your current location. to the previous screen or the X soft-key to exit. Information — Where Am I? • Touch the GPS soft-key to view the GPS information. • Touch the Save soft-key to save the location in your Favorites. NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
368 Uconnect® 8.4AN Information — Trip Computer Trip Computer displays the following trip information from your last trip • Travel Direction • Distance to final Destination • Vehicle Speed • Distance Traveled • Overall average speed • Moving average speed • Maximum speed reached • Total time traveled To select Trip Computer information, touch the Information soft-key from the Nav Main Menu and then touch • Travel time spent moving the Trip Computer soft-key.
Uconnect® 8.4AN 369 Emergency • Police – Search and route to a Police Station close to your current location • Fire Department – Search and route a Fire Department close to your current location Touch the Location soft-key to display your exact current location. Touch the Save soft-key to save your current location in Favorites. NOTE: You can touch the back arrow soft-key to return to the previous screen or the X soft-key to exit.
370 Uconnect® 8.4AN Emergency — Hospital You can search for a Hospital by the following categories, which are soft-key tabs at the top of the screen: • Name • Distance • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. Touch the desired Hospital and touch Yes to confirm the destination.
Uconnect® 8.4AN 371 You can touch the back arrow soft-key to return to the You can search for a Police Station by the following categoprevious screen or the X soft-key to exit. ries, which are soft-key tabs at the top of the screen. Emergency — Police • Name • Distance • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. Touch the desired Police Station and touch Yes to confirm the destination.
372 Uconnect® 8.4AN You can touch the back arrow soft-key to return to the You can search for a Fire Department by the following previous screen or the X soft-key to exit. categories, which are soft-key tabs at the top of the screen. Emergency — Fire Department • Name • Distance • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. Touch the desired Fire Department and touch Yes to confirm the destination.
Uconnect® 8.4AN 373 You can touch the back arrow soft-key to return to the 3. Coast-to-coast delivery of traffic information. previous screen or the X soft-key to exit. 4. View conditions for points along your route and beyond. SiriusXM Traffic — U.S. Market Only (Available On 8.4AN, If Equipped) SiriusXM Travel Link — U.S. Market Only Don’t drive through traffic. Drive around it. (Available On 8.4AN, If Equipped) Avoid congestion before you reach it.
374 Uconnect® 8.4AN • Sports Scores -- In-game and final scores as well as • SiriusXM Travel Link is only available in the continenweekly schedules. tal United States. • Movie Listings -- Check local movie theatres and Security Features listings in your area and route to the theater of your The following Security Related options are available: choice. • SiriusXM Travel Link feature is completely integrated • 9–1–1 Call into your vehicle.
Uconnect® 8.4AN 375 In order to provide Uconnect® Services to you, we may record and monitor your conversations with Roadside Assistance, Uconnect® Care or Vehicle Care, whether such conversations are initiated through the Uconnect® Services in your vehicle, or via a landline or mobile telephone, and may share information obtained through such recording and monitoring in accordance with regulatory requirements.
376 Uconnect® 8.4AN 4. You should be able to speak with the 9-1-1 operator 6. If a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit certain through the vehicle audio system to determine if vehicle information to a 9-1-1 operator, including the additional help is needed. last known GPS coordinates of your vehicle.
Uconnect® 8.4AN 377 WARNING! WARNING! (Continued) If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. a signal to initiate an emergency call. To avoid interference that can cause the 9-1-1 Call system to fail, never add aftermarket equipment (e.g., twoway mobile radio, CB radio, data recorder, etc.
378 Uconnect® 8.4AN If the 9-1-1 Call system detects a malfunction, any of the following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: • The Rearview Mirror light will continuously be illuminated red. • The Phone Screen will display the following message “Vehicle phone requires service. Please contact your dealer.” • An In-Vehicle Audio message will state “Vehicle phone requires service. Please contact your dealer.
Uconnect® 8.4AN 379 Even if the 9-1-1 Call system is fully functional, factors • Equipment malfunction at the 9-1-1 operator facility. beyond Chrysler Group LLC’s control may prevent or • Operator error by the 9-1-1 operator. stop 9-1-1 Call system operation. These include, but are not limited to, the following factors: • Wireless network congestion. • The ignition key has been removed from the ignition • Weather. and the delayed accessories mode is active.
380 Uconnect® 8.4AN WARNING! Failure to perform scheduled maintenance and regularly inspect your vehicle may result in vehicle damage and/or serious injury. General Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SAFETY GUIDELINES CONTENTS 䡵 Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . .
382 SAFETY GUIDELINES Please read and follow these safety precautions. Failure to do so may result in injury or property damage. Safety Guidelines WARNING! ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume all risks related to the use of the Uconnect® features and applications in this vehicle. Only use Uconnect® when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.
SAFETY GUIDELINES 383 • Permanent hearing loss may occur if you play your Touchscreen music or the system at loud volumes. Exercise caution • Do not touch the screen with any hard or sharp objects when setting the volume on your system. (pen, USB stick, jewelry, etc.) which could scratch the • Driving is a complex activity that requires your full touchscreen surface! attention.
384 SAFETY GUIDELINES NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, • Do not insert any damaged, warped, scratched or dirty pursuant to Part 15 of the FCC Rules. These limits are Discs into the Disc player. designed to provide reasonable protection against harm• Discs that have been modified with an adhesive label ful interference in a residential installation. This equipshould not be used in the Disc player.
SAFETY GUIDELINES 385 Safety Information Exposure to Radio Frequency Radiation The radiated output power of the this internal wireless radio is far below the FCC radio frequency exposure limits. Nevertheless, the wireless radio shall be used in such a manner that the radio is 20 cm or further from the human body. The internal wireless radio operates within guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community.
uconnect 8.4A/8.4AN ® 14UC84A-526-AD Fourth Edition Uconnect® 8.4A/8.
