4D241-126-AC Third Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .6 䡵 VAN CONVERSIONS/CAMPERS . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury.
INTRODUCTION 7 frame and underbody as well as the Automobile Infor- VEHICLE MODIFICATIONS/ALTERATIONS mation Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM . . . . . . . . . . . . . .21 ▫ Ignition Node Module (IGNM) — If Equipped. .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .21 ▫ Keyless Ignition Node (KIN) — If Equipped . . .13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .21 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ To Disarm The System . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .27 䡵 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .45 ▫ RKE Air Suspension (Remote Lowering Of The Vehicle) — If Equipped . . . . . . . . . . . . . . . . . .28 ▫ Programming Additional Transmitters. . . . . . . .29 ▫ Transmitter Battery Replacement . . . . . . . . . . .29 ▫ General Information . . . . . . . . . . . . . . . . . . . .32 䡵 REMOTE STARTING SYSTEM — IF EQUIPPED . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Enhanced Seat Belt Use Reminder System (BeltAlert®) . . . . . . . . . . . . . . . . . . . . . . . . . .65 ▫ Seat Belts And Pregnant Women . . . . . . . . . . .66 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .66 ▫ Supplemental Restraint System (SRS) — Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ Air Bag System Components . . . . . . . . . . . . . .68 ▫ Advanced Front Air Bag Features . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a Key Fob with Remote Keyless Entry (RKE) transmitter and an Ignition Node Module (IGNM). The keyless ignition system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Keyless Ignition Node (KIN).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Keyless Ignition Node (KIN) — If Equipped This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START; during start RUN will illuminate.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 To remove the emergency key, slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand. 2 Emergency Key Removal Keyless Enter-N-Go™ Fob (KIN) Emergency Key Removal (IGNM) NOTE: You can insert the double-sided emergency key into the lock cylinder with either side up.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition Place the shift lever in PARK (if equipped with an automatic transmission). Turn the Key Fob to the OFF position and then remove the Key Fob. NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! WARNING! (Continued) • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and push ignition button to place ignition in OFF position. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder SENTRY KEY® Opening the driver’s door when the Key Fob is in the The Sentry Key® Immobilizer System prevents unauignition and the ignition switch position is OFF or ACC, thorized vehicle operation by disabling the engine. The a chime will sound to remind you to remove the Key Fob. system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked NOTE: or unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 During normal operation, after turning on the ignition CAUTION! switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the The Sentry Key® Immobilizer system is not compatbulb check, it indicates that there is a problem with the ible with some aftermarket remote starting systems. electronics.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended. • For vehicles equipped with Keyless Enter-N-Go™, always remember to place the ignition in the OFF position. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: Changes or modifications not expressly approved Light flashing, if the system has not been disabled. If the by the party responsible for compliance could void the condition which initiated the alarm is still present, the system will ignore that condition and monitor the reuser’s authority to operate the equipment. maining doors and ignition.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the horn will sound three times when you unlock the Security System Manual Override doors and the exterior lights will blink three times. Check The Vehicle Security Alarm will not arm if you lock the the vehicle for tampering. doors using the manual door lock plunger. The Vehicle Security Alarm will also disarm if a programmed Sentry Key® is inserted into the ignition ILLUMINATED ENTRY switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 release the LOCK button on the RKE transmitter to lock all doors, the tailgate and the RamBox® (if equipped). • The front courtesy overhead console and door courThe turn signal lights will flash and the horn will chirp to tesy lights will not turn off if the dimmer control is in acknowledge the signal.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob With Remote Keyless Entry (RKE) Transmitter (IGNM) Key Fob With RKE Transmitter Keyless Enter-N-Go™ Fob (KIN) Remote Unlock The Doors Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door. Press the unlock button twice within five seconds to unlock all doors, the tailgate and the RamBox® (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 turn signal lights will flash to acknowledge the unlock 1. Press and hold the LOCK button on a programmed RKE transmitter for at least four seconds, but no signal. The illuminated entry system will also turn on. longer than ten seconds. Then, press and hold the NOTE: The EVIC is setup for driver door first, otherwise UNLOCK button while still holding the LOCK button. this will unlock all doors . 2. Release both buttons at the same time.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature while outside of the vehicle by pressing the LOCK/UNLOCK buttons on the RKE transThis feature will cause the turn signal lights to flash when mitter with the ignition switch in the OFF position and the doors are locked or unlocked with the RKE transmitthe key removed. ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 3. Test the feature while outside of the vehicle by pressing the LOCK button on the RKE transmitter with the This feature will cause the horn to chirp when the doors ignition switch in the OFF position and the key are locked with the RKE transmitter. This feature can be removed. turned on or turned off. To change the current setting, proceed as follows: 4. Repeat these steps if you want to return this feature to its previous setting.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the headlights will turn on, the park lights will flash, the RKE Air Suspension (Remote Lowering Of The horn will pulse on and off, and the interior lights will Vehicle) — If Equipped turn on. For easy entry and loading, your vehicle can be lowered by pressing the Key Fob air suspension lowering button two times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Cancelling Remote Lowering Vehicle lowering can be cancelled at anytime. When vehicle lowering is cancelled, the vehicle will raise up to the next defined level and lock out the remote lowering feature until the ignition has been cycled ON/OFF. Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: To cancel vehicle lowering, press the Key Fob air suspen- • Perchlorate Material — special handling may apply. See www.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Node Module (IGNM) Emergency Key Removal Keyless Ignition Node (KIN) Emergency Key Removal 2. Separating RKE halves requires screw removal and gently prying the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 2 Remove Screw From Transmitter Case Separating Ignition Node Module (IGNM) Transmitter Case
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the RKE transmitter case, snap the two halves together, reposition and secure the screw as shown in step #2 for removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: Changes or modifications not expressly ap- NOTE: proved by the party responsible for compliance could • The vehicle must be equipped with an automatic void the user’s authority to operate the equipment. transmission to be equipped with Remote Start. If your RKE transmitter fails to operate from a normal • Obstructions between the vehicle and the RKE transdistance, check for these two conditions: mitter may reduce this range. 1.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Battery at an acceptable charge level • RKE PANIC button not pressed Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prema• System not disabled from previous remote start event turely: • Fuel meets minimum requirement • Vehicle security alarm not active WARNING! • Do not start or run an engine in a closed gara
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode. Press and release the REMOTE START button on the RKE transmitter twice within five sec- • The engine can be started two consecutive times (two onds. The parking lights will flash, vehicle 15-minute cycles) with the RKE transmitter.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm System (if equipped). Then, prior to the end of the 15 minute cycle, press and release the START/STOP button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 DOOR LOCKS Manual Door Locks Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when Front and rear doors may be locked by moving the lock closed. knob down or unlocked by moving the lock knob up. The emergency key will unlock the driver door lock on your vehicle. WARNING! • Do not leave children or animals inside parked vehicles in hot weather.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Before exiting a vehicle, always turn the vehicle OFF, apply the parking brake, shift the automatic transmission into PARK or the manual transmission into REVERSE, and remove the Key Fob from the ignition. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 operate. A chime will sound if the Key Fob is in the ignition switch and a door is open, as a reminder to remove the Key Fob. Automatic Door Locks — If Equipped The auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of the customer.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Doors Unlock Programming — If Equipped The Automatic Doors Unlock feature can be enabled or disabled as follows: For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (System Setup)” in “Understanding Your Instrument Panel” for further information. NOTE: Use the Auto Unlock Doors feature in accordance with local laws.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: • After setting the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle. KEYLESS ENTER-N-GO™ Child Lock Control WARNING! Avoid trapping anyone in a vehicle in a collision.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To Unlock From The Driver’s Side: • Passive Entry may be programmed ON/OFF; refer to With a valid Passive Entry RKE transmitter within 5 ft “Uconnect® Settings” in “Understanding Your Instru- (1.5 m) of the driver door handle, grab the front driver door handle to unlock the driver’s door automatically. ment Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: If “Unlock All Doors 1st Press” is programmed, all doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press”, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Vehicle’s Doors With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, press the door handle LOCK button to lock all doors. Do NOT grab the door handle when pressing the door handle lock button. This could unlock the door(s).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: WINDOWS • After pressing the door handle LOCK button, you Power Windows — If Equipped must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • The Passive Entry system will not operate if the RKE transmitter battery is dead.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the front passenger door for passenger window control and on the rear doors of the Quad Cab and Crew Cab models. The windows will operate when the ignition switch is turned to the ON/RUN or ACC position, and for up to 10 minutes after the ignition is turned OFF or until a front door is opened. WARNING! (Continued) particularly unattended children, can become entrapped by the windows while operating the power window switches.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 NOTE: If the window runs into any obstacle during the auto-closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch Lift the window switch fully upward to the second again to close the window. Any impact due to rough road detent, release, and the window will go up automatically. conditions may trigger the auto reverse function unexpectedly during auto closure.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed. 3. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 open or partially open positions. This is a normal occur- • Supplemental Side Air Bag Inflatable Curtains (SABIC) rence and can be minimized. If the buffeting occurs with — if equipped the rear windows open, then open the front and rear • Supplemental Seat-Mounted Side Air Bags (SAB) windows together to minimize the buffeting.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this 1. Children 12 years old and under should always ride section. It tells you how to use your restraint system buckled up in a rear seat. properly, to keep you and your passengers as safe as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 children to slide the shoulder belt behind them or under 5. If the air bag system in this vehicle needs to be their arm. modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided If a child from 2 to 12 years old (not in a rear facing child under ⴖIf You Need Assistanceⴖ. seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Supplemental Side Air Bag Inflatable Curtain (SABIC) and Seat-Mounted Side Air Bags (SAB) also need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 2 Pulling Out Latch Plate And Webbing 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Regular Cab Front Center Three Point Belt The belt will automatically retract to its stowed posi1. The front center seat belt on the Regular Cab may be tion. If necessary, slide the latch plate down the disconnected to open up utilization of the storage webbing to allow the belt to retract fully. areas behind the front seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 2 Detaching Buckle With Seat Belt Tongue 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seat belt usage, refer “Lap/Shoulder Belt Operating Instructions”.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In Use Position • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Center Lap Belts Seat Belts In Passenger Seating Positions The center seating position for the Quad Cab®, Mega Cab® and Crew Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a “click”. To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing. Wear the lap belt snug against the hips.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 For Standard Cab Only First Row Second Row Driver N/A N/A Automatic Locking Retractor (ALR) Mode — If Equipped Center ALR N/A • N/A — Not Applicable • ALR — Automatic Locking Retactor Passenger ALR N/A In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will Energy Management Feature hear a clicking sound. This indicates the safety belt is This vehicle has a safety belt system with an Energy now in the Automatic Locking Mode. Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on How To Disengage The Automatic Locking Mode collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 NOTE: These devices are not a substitute for proper seat Reminder Light and sounding an intermittent chime. belt placement by the occupant. The seat belt still must be Once the sequence starts, it will continue for the entire duration or until the respective seatbelts are fastened. worn snugly and positioned properly.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert® can be enabled or disabled by your autho- Seat Belt Extender rized dealer. Chrysler Group LLC does not recommend If a seat belt is too short even when fully extended and deactivating BeltAlert®.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the air bag covers.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bags have a multistage inflator protection for an occupant during a side impact. The design. This allows the air bag to have different rates of Supplemental Seat-Mounted Side Air Bags are located in inflation based on several factors, including the severity the outboard side of the front seats. and type of collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • Knee Impact Bolsters • Driver Advanced Front Air Bag • Passenger Advanced Front Air Bag determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors (if equipped). The first stage inflator is triggered immediately during an impact that requires air bag deployment. This low output • Supplemental Seat-Mounted Side Air Bags (SAB) is used in less severe collisions.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Supplemental Side Air Bag Inflatable Curtain (SABIC) — If Equipped SABIC air bags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. • Should a vehicle rollover occur, the pretensioners (if equipped) and/or SAB and SABIC air bags on both sides of the vehicle may deploy. The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 SAB and SABIC air bags are a supplement to the seat belt restraint system. Occupants, including children who are up against or very close to SAB or SABIC air bags can be seriously injured or killed. Occupants, especially children, should not lean on or sleep against the door, side windows, or area where the SAB or SABIC air bags inflate, even if they are in an infant or child restraint.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE including the severity and type of collision. Advanced Seat belts are necessary for your protection in all colliFront Air Bags are not expected to reduce the risk of sions, and also are needed to help keep you in position, away from an inflating air bag. injury in rear, rollover, or side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 turns on the Air Bag Warning Light, either momentarily Driver And Passenger Advanced Front Air Bag or continuously. A single chime will sound if the light Inflator Units comes on again after initial startup.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bag gas is vented through the you if you are not seated properly, or if items are vent holes in the sides of the air bag. In this way, the air positioned in the area where the side air bag inflates. This especially applies to children. bags do not interfere with your control of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 inflates. This especially applies to children. The side Enhanced Accident Response System curtain air bag is only about 3-1/2 in (9 cm) thick when In the event of an impact causing air bag deployment, if it is inflated.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from IGN ON to IGN OFF. If A Deployment Occurs They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the air bags deflate, you may see some smoke-like particles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 located on the inside of the fuse block cover for the • How fast the vehicle was traveling. proper air bag fuses. See your authorized dealer if the These data can help provide a better understanding of fuse is good. the circumstances in which crashes and injuries occur. Event Data Recorder (EDR) NOTE: EDR data are recorded by your vehicle only if a This vehicle is equipped with an event data recorder (EDR).
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years or younger should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-gr
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seatback, should use the seat belt in a rear seat. Use this 5. Can the child stay seated like this for the whole trip? simple 5-step test to decide whether the child can use the If the answer to any of these questions was “no,” then the vehicle’s seat belt alone: child still needs to use a booster seat in this vehicle. If the 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Recommendations For Attaching Child Restraints — Quad Cab®/Crew Cab Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints — Standard Cab, Mega Cab® Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Standard Cab Quad Cab®/Crew Cab Full Bench Lower Anchorage Symbol 2 anchorages per seating Lower Anchorage Symbol 2 anchorages per seating position position Top Tether Anchorage Symbol Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 2 Quad Cab®/Mega Cab®/Crew Cab Split Bench Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab®/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No Never “share” a LATCH anchorage with two or more child restraints.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab®/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Can the rear-facing child restraint touch the back of the front passenger seat? Can the head restraints be removed? Yes The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages In addition, Regular Cab models have tether strap anchorages behind the front center and right seats. Quad Cab®, Mega Cab® and Crew Cab models have tether strap anchorages located behind each of the rear seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH — Standard Cab/Quad Cab®/Crew Cab Full Bench Do not install a child restraint in the center position using the LATCH system. Use the seat belt and tether anchor to install a child seat in the center seating position.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Center Seat LATCH — Quad Cab®/Mega Cab®/Crew Cab Split Bench To Install A LATCH-compatible Child Restraint 1. If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, do not install a child seat in that outboard 2. position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • Child restraint anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle 2 Quad Cab®/Mega Cab®/Crew Cab Standard Cab
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab®/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? Weight limit of the Child Restraint Yes Yes Always use th
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Mega Cab®/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? 65 lbs (29.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract 1. Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 strap. See the section “Installing Child Restraints Using the Top Tether Anchorage” for directions to attach a tether anchor. rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the car seat. 9. Test that the child restraint is installed tightly by 2.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE strap. Refer to “Installing Child Restraints Using The If the belt still cannot be tightened after you shorten the Top Tether Anchorage” for directions to attach a tether buckle, disconnect the latch plate from the buckle, turn the buckle around one half turn, and insert the latch plate anchor. into the buckle again. If you still cannot make the child 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head restraint and between its posts. 3. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never place a rear facing infant seat in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. Mega Cab® Tether Strap Mounting Quad Cab® or Crew Cab Trucks: The top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 2 Head Restraint In Raised Position Tether Strap Loop With Center Head Restraint In Raised Position 2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind the center seat.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pass the tether strap hook under the head restraint 4. Attach the hook to the center tether strap loop (see behind the child seat, though the tether strap loop diagram). Tighten the tether strap according to the behind the seat and over to the center tether strap child seat manufacturer’s instructions. loop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 NOTE: If there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats. 2 Center Seat: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. Tether Strap Loop With Head Restraint In Raised Position 2.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pass the tether strap hook under the head restraint 4. Attach the hook to the outboard tether strap loop (see behind the child seat, though the tether strap loop diagram). Tighten the tether strap according to the behind the seat and over to the right or left outboard child seat manufacturer’s instructions. tether strap loop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 Installing Three Child Restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above. 2 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3. Place a child restraint on the center rear seat. Route the tether strap following the directions for the center seating position, above. 4.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • If you are required to drive with the trunk/liftgate/ rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 seams or loose connections could permit exhaust fumes Air Bag Warning Light to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised The light should come on and remain on for four for lubrication or oil change. Replace as required. to eight seconds as a bulb check when the ignition switch is first turned ON.
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 119 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 ▫ Heated Mirrors — If Equipped . . . . . . . . . . .139 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .128 ▫ Driver’s Outside Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . .139 ▫ Automatic Dimming Mirror — If Equipped . . .128 ▫ Automatic Dimming Mirror With Rear View Camera Display — If Equipped . . . . . . . . . . .134 ▫ Outside Mirrors . . . . .
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Power Lumbar — If Equipped . . . . . . . . . . . .144 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .145 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . .163 ▫ Ventilated Seats — If Equipped . . . . . . . . . . . .147 ▫ Automatic Headlights — If Equipped . . . . . . .163 ▫ Manual Seat Adjuster — If Equipped. . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .168 ▫ Rain Sensing Wipers — If Equipped . . . . . . . .176 ▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . .171 䡵 TILT STEERING COLUMN . . . . . . . . . . . . . . .177 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . .172 䡵 HEATED STEERING WHEEL — IF EQUIPPED . . .178 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ ParkSense® Sensors . . . . . . . . . . . . . . . . . . . .186 ▫ ParkSense® Warning Display . . . . . . . . . . . . .186 ▫ ParkSense® Display . . . . . . . . . . . . . . . . . . . .187 ▫ Enabling And Disabling ParkSense® . . . . . . .190 ▫ Enabling And Disabling Front And/Or Rear ParkSense® . . . . . . . . . . . . . . . . . . . . . . . . . .198 ▫ Service The ParkSense® Park Assist System . . .199 ▫ Cleaning The ParkSense® System . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 ▫ Before You Begin Programming HomeLink® . .208 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .218 ▫ Programming A Rolling Code . . . . . . . . . . . .209 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .218 ▫ Programming A Non-Rolling Code . . . . . . . . .211 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . . .218 ▫ Canadian/Gate Operator Programming . . . . .212 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Rear Cupholder — Quad Cab®. . . . . . . . . . . .227 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .236 ▫ Rear Cupholder — Crew Cab . . . . . . . . . . . . .227 ▫ Power Sliding Rear Window — If Equipped . .237 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .228 ▫ Manual Sliding Rear Window — If Equipped . . .238 ▫ Glove Compartment . . . . . . . . . . . . . . . . . . .228 䡵 FOLD FLAT LOAD FLOOR — IF EQUIPPED . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 ▫ Bed Rail Tie-Down System . . . . . . . . . . . . . .255 ▫ Locking Tailgate . . . . . . . . . . . . . . . . . . . . . .260 䡵 SLIDE-IN CAMPERS . . . . . . . . . . . . . . . . . . . .257 䡵 TRI-FOLD TONNEAU COVER — IF EQUIPPED. . . . . . . . . . . . . . . . . . ▫ Camper Applications . . . . . . . . . . . . . . . . . . .257 ▫ Tri-Fold Tonneau Cover Removal . . 䡵 EASY-OFF TAILGATE . . . . . . . . . . . . . . . . . . .257 ▫ Tri-Fold Tonneau Cover Installation.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. NOTE: • The Automatic Dimming Mirror feature is disabled when the vehicle is in reverse gear to improve rear view viewing. • The Automatic Dimming Mirror feature can be turned on or off using the Uconnect® System. Automatic Dimming Mirror – Press the controls soft-key.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Assist Call The rear view mirror contains an ASSIST push button which automatically connects the vehicle occupants to one of several predefined locations for immediate support: NOTE: In case the 9-1-1 Call button is pushed in error, there will be a 10 second delay before the 9-1-1 Call system initiates a call to a 9-1-1 operator.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 4. You should be able to speak with the 9-1-1 operator through the vehicle audio system to determine if additional help is needed. NOTE: Once a connection is made between the vehicle’s 9-1-1 Call system and the 9-1-1 operator, the 9-1-1 operator may be able to open a voice connection with the vehicle to determine if additional help is needed.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Modifications to any part of the 9-1-1 Call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to help protect you. 9-1-1 Call System Limitations Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system capabilities. 9-1-1 or other emergency line operators in Canada and Mexico may not answer or respond to 9-1-1 system calls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Even if the 9-1-1 Call system is fully functional, factors • Operator error by the 9-1-1 operator. beyond Chrysler Group LLC’s control may prevent or • Wireless network congestion. stop the 9-1-1 Call system operation. These include, but are not limited to, the following factors: • Weather. • The ignition key has been removed from the ignition • Buildings, structures, geographic terrain, or tunnels. and the delayed accessories mode is active.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. When the vehicle is placed into reverse gear a video display illuminates to display the image generated by the rear view camera located on the tailgate handle. The auto dimming feature is also disabled to improve rear view viewing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirrors All outside mirrors are designed to be able to be manually to center on the adjacent lane of traffic with a slight folded both forward and rearward to prevent damage. overlap of the view obtained on the inside mirror. 3 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. If the mirror is manually folded after electrically cycled, a potential extra button push is required to get the mirrors back to the home position. If the mirror does not electrically fold check for ice or dirt build up at the pivot area which can cause excessive drag.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Resetting the Power Folding Outside Mirrors Power Mirrors — If Equipped You may need to reset the power folding mirrors if the The controls for the power mirrors are located on the driver’s door trim panel. following occurs: • The mirrors are accidentally blocked while folding. 3 • The mirrors are accidentally manually folded/ unfolded. • The mirrors come out of the unfolded position. • The mirrors shake and vibrate at normal driving speeds.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power mirror controls consist of mirror select but- To adjust a mirror, press either the L (left) or R (right) tons and a four-way mirror control switch. button to select the mirror that you want to adjust.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Heated Mirrors — If Equipped Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. These mirrors are heated to melt frost or ice. This To use the mirror, rotate the sun visor down and swing feature can be activated whenever you turn on the the mirror cover upward. The lights will turn on autorear window defroster (if equipped). Refer to “Rear matically. Closing the mirror cover turns off the light.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Slide-On-Rod” Features Of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun. To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 NOTE: Fold the trailer towing mirrors rearward prior to These mirrors are designed with an adjustable mirror entering an automated car wash. head to provide a greater vision range when towing A small blindspot mirror is located next to main mirror extra-wide loads. To change position inboard or out- and can be adjusted separately. board, the mirror head should be rotated (flipped in or out).
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS outboard side of the driver’s seat cushion. There are two Seats are a part of the Occupant Restraint System of the power seat switches that are used to control the movement of the seat cushion and the seatback. vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Adjusting The Seat Forward Or Rearward Reclining The Seatback The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Lumbar Control Switch Heated Seats — If Equipped On some models, the front and rear seats may be equipped with heaters located in the seat cushions. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the seats independently. The controls for each seat are • The engine must be running for the heated seats to located near the bottom center of the instrument panel operate. (below the climate controls) or in the radio unit. The heated seats switch from HIGH to LOW and from You can choose from HIGH, LOW or OFF heat settings. LOW to OFF automatically, based on time and temperaRed indicator lights in each switch indicate the level of ture of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Rear Heated Seats • The engine must be running for the heated seats to operate. On some models, the two outboard seats are equipped with heated seats. The heated seat switches for these When the HIGH-level setting is selected, the heater will seats are located on the rear of the center console. provide a boosted heat level during the first four minutes of operation.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ventilated seat switches are located in the switch bank Vehicles Equipped With Remote Start in the center stack of the instrument panel just below the On models equipped with remote start, the drivers climate controls as well as soft-keys located in the radio ventilated seat can be programmed to come on during a screen. The fans operate at two speeds, HIGH and LOW. remote start.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 While sitting in the seat, pull up on the handle and slide Both front seats are adjustable forward or rearward. The the seat forward or backward. Release the bar once you manual seat adjustment handle is located under the seat have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be cushion at the front edge of each seat. sure that the seat adjusters have latched.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dump Feature (Manual Recline Seat Only) — Standard Cab Actuating the recliner handle will allow the seatback to swing (dump) forward on manual recliner seats. This “dump” feature allows access to the storage bin behind the seat. WARNING! • Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Folding Rear Seat (Table Mode) — If Equipped Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint. Rear Seat Recliner Handle WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback forward. Folding Rear Seat — If Equipped Both the outboard rear seats will drop and move forward when the seatback is folded flat. WARNING! Table Mode 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! (Continued) • Cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop or collision and strike someone in the vehicle, causing serious injury or death. 3 To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down and push the seat forward. WARNING! An improperly latched seat could cause serious injury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. Head Restraints Rear Passenger Fold-Flat Seats 3. Lift the seatback, to return the seat to the upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Front Head Restraints To raise the head restraint, pull upward on the head Adjustment Button restraint.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer. DRIVER MEMORY SEAT — IF EQUIPPED Adjustment Button NOTE: • The rear center head restraint (Crew Cab and Quad Cab) has only one adjustment position that is used to aid in the routing of a tether.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 The memory seat buttons are located on the outboard Programming The Memory Feature side of the drivers seat cushion. NOTE: To create a new memory profile, perform the following: Vehicles Equipped With Keyless Enter-N-Go 1. Without pressing the brake pedal, push the ENGINE START/STOP button and cycle the ignition to the ON/RUN position (do not start the engine). 2.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Not Equipped With Keyless Enter-N-Go NOTE: 1. Insert the ignition Key Fob, and turn the ignition • Memory profiles can be set without the vehicle in switch to the ON/RUN position. PARK, but the vehicle must be in PARK to recall a memory profile. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: Before programming your RKE transmitters you 3. Once the profile has been recalled, press and release must select the “Memory To FOB” feature through the the SET (S) button on the memory switch, then press and release button (1) or (2) accordingly. “Memory Uconnect® system screen. Refer to “Customer- ProgramProfile Set” (1 or 2) will display in the instrument mable Features — Uconnect® Access 8.4 Settings ” in cluster on vehicles equipped with the EVIC.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To recall the memory settings for driver two using the RKE transmitter, press the UNLOCK button on the • To recall the memory settings for driver one using the RKE transmitter linked to memory position 2. memory switch, press MEMORY button number 1 on A recall can be cancelled by pressing any of the the memory switch. MEMORY buttons during a recall (S, 1, or 2).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 3 Hood Release 2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. Safety Latch Location (1500 Series Shown) CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the AUTO position.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 90 seconds after you turn the ignition switch to the OFF Daytime Running Lights (DRL) — If Equipped position. To turn the automatic headlights off, turn the The headlights on your vehicle will illuminate when the headlight switch out of the AUTO position. engine is started and the transmission is in any gear NOTE: The engine must be running before the head- except PARK. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Headlight delay can be cancelled by either turning the detects vehicle specific light and automatically switches headlight switch on then off, or by turning the ignition from high beams to low beams until the approaching vehicle is out of view. ON. The headlight delay time is programmable on vehicles NOTE: equipped with an Electronic Vehicle Information Center • Automatic High Beam Headlamp Control can be (EVIC) or a Uconnect® system screen.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate To Deactivate 1. Select “Automatic High Beams — ON” through the Perform either of the following steps to deactivate the EVIC. Refer to “Electronic Vehicle Information Center Automatic High Beam system. (EVIC)/Customer-Programmable Features” in “Un1. Select “Automatic High Beams — OFF” through the derstanding Your Instrument Panel” for further inforEVIC. Refer to “Electronic Vehicle Information Center mation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Parking Lights And Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the O (Off) position. 3 Fog Lights — If Equipped The fog lights are turned on by rotating the headlight switch to the parking light or headlight position and pushing in the headlight rotary control.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn off when the switch is pushed a second time, when eight minutes. If the headlights are turned on and left on the headlight switch is rotated to the off position, or the for eight minutes while the ignition is OFF, the exterior lights will automatically turn off. high beam is selected. Lights-On Reminder NOTE: Battery saver mode is cancelled if the ignition is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 The brightness of the instrument panel as well as the ambient lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odometer, radio and overhead console by rotating the control to the right until you hear a click. This feature is termed the “Parade” mode and is useful when headlights are required during the day.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. Rear Passenger Courtesy/Reading Light Front Courtesy/Reading Lights NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Ambient Light Cargo Light The overhead console is equipped with an ambient light The cargo lights are turned on by pressing on the cargo feature. This light casts illumination for improved visibil- button. ity of the floor console area. 3 Cargo Light Switch Ambient Light The cargo lights will also turn on for approximately 30 seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry feature.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever is located on the left side of the steering column. Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Turn Signal Lever NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-To-Pass 3 You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Windshield Wiper Operation Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. The wipers and washers are operated by a switch in the Rotate the end of the lever upward to the second detent past multifunction lever. Turn the end of the handle to select the intermittent settings for high-speed wiper operation. the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Windshield Washers To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed and the wiper will operate for two to three cycles after the washer knob is released from this position. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the windThis feature senses moisture on the windshield and shield. automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray • Use of Rain-X® or products containing wax or silicone may reduce Rain Sensing performance. from the windshield washers of the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 until the wiper switch is moved, vehicle speed is TILT STEERING COLUMN greater than 0 mph (0 km/h), or the outside temperaThis feature allows you to tilt the steering column ture is greater than 32°F (0°C). upward or downward. The tilt lever is located on the • Transmission In NEUTRAL Position — When the steering column, below the multifunction lever.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. HEATED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 30 to 80 minutes before automatically shutting off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 The heated steering wheel switch is located on the switch — If Equipped” in “Things to Know Before Starting Your bank below the climate controls. There are also soft-keys Vehicle” for further information. in the radio screen that will activate the heated steering wheel. WARNING! Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows the brake, accelerator, and clutch pedals (if equipped) to move toward or away from the driver to provide improved position with the steering wheel. The adjustable pedal switch is located to the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”. CAUTION! • Always adjust the pedals to a position that allows full pedal travel. Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Electronic Speed Control buttons are located on the NOTE: In order to ensure proper operation, the Elecright side of the steering wheel. tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The speed increment shown is dependant on the speed of To Decrease Speed U.S. (mph) or Metric (km/h) units: When the Electronic Speed Control is set, you can decrease speed by pushing the SET (-) button. U.S. Speed (mph) • Pressing the RES (+) button once will result in a 1 mph The speed decrement shown is dependant on the speed increase in set speed. Each subsequent tap of the of U.S. (mph) or Metric (km/h) units: button results in an increase of 1 mph. U.S.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 • If the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established. To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® will retain the last system state (enabled or (150 cm) from the rear fascia/bumper in the horizontal disabled) from the last ignition cycle when the ignition is direction, depending on the location, type and orientation of the obstacle. changed to the ON/RUN position. ParkSense® can be active only when the shift lever is in REVERSE.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 fascia/bumper and the detected obstacle. Refer to “Electronic Vehicle Information Center (EVIC)/Settings” in Understanding Your Instrument Panel” for further information. ParkSense® Display 3 When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the object’s distance and location relative to the vehicle.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Slow Tone Fast Tone
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Distance (in/cm) Audible Alert Chime Arc Greater than 79 in (200 cm) None Radio Volume Reduced No None WARNING ALERTS 79-45 in 45-31 in (200-115 cm) (115-80 cm) Single 1/2 Slow Second Tone 4th Solid 3rd Solid Yes Yes 31-18 in (80-45 cm) Fast Less than 12 in (30 cm) Continuous 2nd Flashing Yes 1st Flashing Yes NOTE: ParkSense® will reduce the volume of the radio, Enabling And Disabling ParkSense® if on, when the system is sounding an audio tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARKSENSE OFF” message for as long as the vehicle is in REVERSE. NOTE: The ParkSense® system will automatically disable when the system detects that a trailer with trailer brakes has been connected to the Integrated Trailer Brake Module.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear fascia/bumper is clean and clear of snow, ice, • Jackhammers, large trucks, and other vibrations could affect the performance of ParkSense® . mud, dirt or other obstruction, and then cycle the ignition. If the message continues to appear, see an autho• When you turn ParkSense® off, the instrument cluster rized dealer. will display ⬙PARKSENSE OFF⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ bumper. • Ensure the ParkSense® system is OFF if objects such as bicycle carriers, trailer hitches, etc., are placed within 18 in (45 cm) from the rear fascia/bumper while driving the vehicle.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using ParkSense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 up or moving forward, e.g. during a parking maneuver. ParkSense® Sensors Refer to ParkSense® System Usage Precautions for limi- The four ParkSense® sensors, located in the rear fascia/ tations of this system and recommendations. bumper, monitor the area behind the vehicle that is ParkSense® will retain the last system state (enabled or within the sensors’ field of view.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Warning Display ParkSense® Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Customer Programmable Features section of the Electronic Vehicle Information Center (EVIC) or from the Uconnect® System (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Rear Distance (in/cm) Front Distance (in/cm) Audible Alert (Chime) Greater than 79 in (200 cm) Greater than 47 in (120 cm) None Arcs Radio Volume Reduced None No WARNING 79-45 in (200-115 cm) 47-39 in (120-100 cm) Single 1/2 Second Tone (for rear only) 4th Solid Yes ALERTS 45-31 in (115-80 cm) 39-25 in (100-65 cm) Slow (for rear only) 31-18 in (80-45 cm) 25-12 in (65-30 cm) Fast Less than 18 in (45 cm) Less than 12 in (30 cm) Continuous 3rd Solid Yes
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Chime Volume Settings Front and Rear chime volume settings can be selected from the EVIC or Uconnect® System — if equipped. Rear ParkSense® can be enabled and disabled with the Rear ParkSense® switch. When the Front or Rear ParkSense® switch is pressed to disable the system, the instrument If Uconnect® System is equipped, chime volume settings cluster will display the “PARKSENSE OFF” will not be accessible from the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 NOTE: Arc alerts from the enabled ParkSense® system, will interrupt the five second messages, and the EVIC will display the car graphic with the corresponding arcs and ⬙OFF⬙ message. The Front or Rear ParkSense® switch LED will be ON when Front or Rear ParkSense® is disabled or requires service. The Front or Rear ParkSense® switch LED will be OFF when the Front or Rear system is enabled.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Center (EVIC)” in “Understanding Your ParkSense® System Usage Precautions Instrument Panel” for further information. NOTE: If ⬙PARKSENSE UNAVAILABLE WIPE REAR SENSORS⬙ • Ensure that the front and rear bumper are free of snow, or ⬙PARKSENSE UNAVAILABLE WIPE FRONT SENice, mud, dirt and debris to keep the ParkSense® SORS⬙ appears in the Electronic Vehicle Information system operating properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 PARKSENSE OFF⬙ or ⬙REAR PARKSENSE OFF⬙ message for five seconds, followed by a car graphic with ⬙OFF⬙ in the corresponding side. This car graphic will be displayed for as long as the vehicle is in REVERSE. system misinterpreting a close obstacle as a sensor problem, causing the “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message to be displayed in the instrument cluster.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! (Continued) • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense®. • Before using ParkSense®, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 lever is put into REVERSE. The image will be displayed in the rearview mirror display — if equipped or Uconnect® screen — if equipped along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear. When enabled, active guide lines are overlaid on the image to illustrate the width of the vehicle and its projected backup path based on the steering wheel position.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following table shows the approximate distances for each zone: Zones Red Yellow Green Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) 1 ft - 3 ft (30 cm - 1 m) 3 ft or greater (1 m or greater) WARNING! Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Turning ParkView® On Or Off — With Uconnect® 5.0 1. Turn the Radio on. 2. Touch the “Settings” button. 3. Touch the “Safety & Assistance” soft-key. 3. Touch the “Safety & Driving Assistance” soft-key. 4. Touch the “Parkview Backup camera” soft-key to turn the ParkView® system ON or OFF. NOTE: A check mark will appear in the selection box to indicate the system is turned ON. 4.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 GARAGE DOOR OPENER — IF EQUIPPED HomeLink® that operate ized gates, HomeLink® battery. replaces up to three hand-held transmitters devices such as garage door openers, motorlighting or home security systems. The unit is powered by your vehicles 12 Volt The HomeLink® buttons that are located in the overhead console designate the three different HomeLink® channels.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. 3 Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand - held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program. attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 2. Place the hand - held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to To reprogram a channel that has been previously trained, program. follow these steps: 3. Simultaneously press and hold both the Homelink® 1. Turn the ignition switch to the ON/RUN position. button you want to program and the hand - held 2. Press and hold the desired HomeLink® button until transmitter button. the EVIC displays “CHANNEL # TRAINING” Do not 4.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Press and hold the programmed HomeLink® button. The EVIC will display “CHANNEL # TRANSMIT.” If the garage door opener/device activates, programming is complete. Canadian/Gate Operator Programming For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 3. Simultaneously press and hold both the Homelink® Reprogramming A Single HomeLink® Button button while you press and release (“cycle”), your To reprogram a channel that has been previously trained, hand - held transmitter every two seconds. follow these steps: 4. Continue to hold buttons until the EVIC display 1. Turn the ignition switch to the ON/RUN position. changes from “CHANNEL # TRAINING” to “CHAN2.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Did you unplug the device for programming and remember to plug it back in? It is advised to erase all channels before you sell or turn in your vehicle. If you have any problems, or require assistance, please To erase the channels press and hold the two outside call toll-free 1-800-355-3515 or, on the Internet at HomeLink® buttons (I and III) for up 20 seconds. The www.HomeLink.com for information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 WARNING! (Continued) or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or assistance.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console between the courtesy/reading lights. Power Sunroof Switch WARNING! • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 WARNING! (Continued) • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature Sunshade Operation This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Sunroof Maintenance ELECTRICAL POWER OUTLETS Use only a nonabrasive cleaner and a soft cloth to clean The auxiliary 12 Volt (13 Amp) power outlets can provide the glass panel. power for in-cab accessories designed for use with the standard “cigar lighter” plug.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The auxiliary power outlets can be found in the following • Lower left and lower right of the center stack when locations: equipped with a bench seat. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watts (13 Amps) power rating is exceeded, the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 • Center console when equipped with bucket seats. 3 Power Outlet — Upper Lid Power Outlet — Center Console • Inside the upper lid of the center storage compartment — if equipped.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Rear of the center console storage compartment — The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC positions. Quad Cab® or Crew Cab. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools. 3 The power inverter is designed with built-in overload protection.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. Front Instrument Panel Cupholders — Floor Mounted Shifter For vehicles equipped with bucket seats there are two cupholders located in the floor console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 Rear Cupholder — Quad Cab® Rear Cupholder — Crew Cab Quad Cab® vehicles may be equipped with a rear Crew Cab vehicles are equipped with rear cupholders cupholder that consists of two cup wells for rear passen- located in the center armrest. ger convenience. 3 Crew Cab Rear Armrest Cupholder Rear Cup Wells Crew Cab vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cup Wells STORAGE Glove Compartment The glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area. Glove Compartment 1 — Upper Glove Compartment 2 — Lower Glove Compartment To open the upper glove compartment push upward on the handle release. The glove compartment door will automatically open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 3 Upper Glove Compartment To open the lower glove compartment, pull on the handle to release the latch and lower the glove compartment door.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage Rear Door Storage — Crew Cab Front Door Storage — If Equipped Storage compartments are located in both the driver and passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Upper Storage Compartment Lower Storage Bin With the upper lid closed, pull on the lower handle to open the lower storage bin. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 To open in-floor storage bin, lift upward on the handle of In-floor storage bins are located in front of the second the latch and open the lid. row seats and can be used for extra storage. The storage NOTE: The front seat may have to be moved forward to bins have removable liners that can be easily removed for fully open the lid. cleaning.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seatback Storage Storage (Regular Cab) Located in the back of both the driver and passenger The storage bin is located behind the front seats and runs front seats are pockets that can be used for storage. the length of the cab.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Crew Cab Storage CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the switch to the right to open the glass. Pull the Unfolding the Load Floor switch to the left to close the glass. 1. Lift the 60/40 seat cushion(s) to the upward position. Manual Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 2. Grasp the knob on the load floor and lift the knob until Positioning the Load Floor for Storage Access Under the load floor unfolds into position. the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. WARNING! Load Floor In Open Position 3. Reverse the procedure to store the load floor.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Load Floor Securing Straps Pick Up Box Features 4. Reverse the procedure to put the load floor back in the 1 — Upper Load Floor Indents secured down position before you operate the vehicle. 2 — Bulk Head Dividers 3 — Cleats PICKUP BOX The pickup box has many features designed for utility and convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 NOTE: If you are installing a Toolbox, Ladder Rack or Headache Rack at the front of the Pickup Box, you must use Mopar Box Reinforcement Brackets that are available from your authorized dealer. You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. NOTE: If the vehicle speed remains below 8 mph (13 km/h), the cargo camera image will be displayed continuously until deactivated by touching the Uconnect® display.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 RAMBOX® — IF EQUIPPED The RamBox® system is an integrated pickup box storage and cargo management system consisting of three features: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system RamBox® Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is properly secured. • Do not exceed cargo weight rating of 150 lb (68 kg) 1500 series vehicles or 300 lbs (136 kg) for 2500 and 3500 series vehicles per bin. RamBox® Cargo Storage Bins To open a storage bin with the RamBox® unlocked, press and release the button located on the lid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 3 RamBox® Pushbutton And Lock The interior of the RamBox® will automatically illuminate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the lights back on.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch. Cargo bins feature two removable drain plugs (to allow water to drain from bins). To remove plug, pull up on the edge. To install push plug downward into drain hole.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 CAUTION! (Continued) WARNING! (Continued) • Damage to the RamBox® bin may occur due to heavy/sharp objects placed in bin that shift due to vehicle motion. In order to minimize potential for damage, secure all cargo to prevent movement and protect inside surfaces of bin from heavy/sharp objects with appropriate padding. • Do not allow children to have access to the storage bins. Once in the storage bin, young children may not be able to escape.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bed Extender — If Equipped The bed extender has three functional positions: • Storage Position • Divider Position • Extender Position Storage Position The storage position for the bed extender is at the front of the truck bed which maximizes the bed cargo area when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 3 Center Handle And Lock 1 — Center Handle Lock 2 — Handle 2. With the side gates open, position the extender fully forward in the bed against the front panel. Storage Position 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie Down Loop Side Gates Closed 4. Rotate the center handle horizontally to secure the side 5. Lock the center handle using the vehicle key to secure gates in the closed position. the panel into place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 Divider Position The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo. 3 To install the bed extender into a divider position perform the following: 1.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Aligning Gate To Slots Side Gates Closed 3. Rotate the side gates closed so that the outboard ends 5. Lock the center handle to secure the panel into place. are secured into the intended slots of the bed. Extender Position 4. Rotate the center handle horizontally to secure the side The extender position allows you to load the bed of the gates in the closed position. truck beyond the tail gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 additional cargo room is needed. The extender position 2. Make sure the center handle is unlocked and rotate the utilizes a locating pin and rotating handle located on both center handle vertically in order to release the extender side gates. sides of the truck bed near the tailgate. 3. Fit the end of the side gate ends onto the pin and handle. Extender Position To install the bed extender into the extender position perform the following: 1.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the handles to the horizontal position to secure into place. Locking Tab WARNING! To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. • When vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur. 3 There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out on the cleat and slide it to the detent nearest the To remove the cleats from the utility rail, remove the end desired location. Make sure the cleat is seated in the cap screw located in the center of the end cap, using a detent and tighten the nut. #T30 Torx® head driver. Remove the end cap and slide the cleat off the end of the rail.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 SLIDE-IN CAMPERS EASY-OFF TAILGATE Camper Applications To simplify mounting of a camper unit with an overhang, the tailgate can be removed. Certain truck models are not recommended for slide-in campers.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disconnecting the Rear Camera or Remote Keyless Entry — If Equipped 1. Open the tailgate to access the rear camera or RKE connector bracket located on the rear sill. Locking Tab 3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill. 4. Connect the chassis plug and bracket (provided in the glove box) to the chassis wiring harness and insert the bracket back into the sill. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will prevent damaging the connector and bracket when storing or reinstalling the tailgate. 3 Removing The Tailgate 1.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Remove the tailgate from the vehicle. TRI-FOLD TONNEAU COVER — IF EQUIPPED NOTE: Do not carry the tailgate loose in the truck Your vehicle may be equipped with a Tri-Fold Tonneau Cover which consists of different features: pickup box. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Tri-Fold Tonneau Cover Removal To remove the Tonneau Cover follow the following steps: 1. Lower the tailgate to gain access to the first set of two tonneau cover clamps located on the driver and passengers bottom side of the tonneau cover. 3 Clamped Position NOTE: If clamp wire is damaged replace immediately.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull down on the first set of clamps on both driver and passenger sides to the semi clamped position. Proper Released Position Semi Clamped Position 3. Pull down on the clamp wire and push the clamp up into the proper released position. NOTE: Be sure the clamp and clamp wire is in the proper released position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 4. Pick up on the tonneau cover and fold it back into the second panel. 5. Pick up on the cover and fold it back into the third panel. 6. Once in the third panel position pull down on the second set of clamps on both driver and passenger sides to the semi clamped position. Improper Clamp Wire Released Position CAUTION! Make sure the tonneau cover clamp and clamp wire is in the proper released position.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Semi Clamped Position Proper Released Position 7. Pull down on the clamp wire and push the clamp up 8. Be sure to clip both stowage straps together to insure into the proper released position. the cover stays together.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 Tri-Fold Tonneau Cover Installation To install the Tonneau Cover follow the following steps: 1. Position the folded Tonneau Cover on the truck bed and push the Cover forward against the front of the truck bed. The Tonneau Cover centers itself when placed on the vehicle. 2. Pull down on the first set of clamp handles to release the clamps from the stowed position. Stowage Strap 9. With two people remove the cover.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stowed Position Semi Clamped Position 3. Push clamp wires up and under the flange of box (or 4. Push clamp handles upward to the clamped position flange of Ram Box rail, if equipped) to the semi to properly engage the clamps. clamped position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 3 Clamped Position Improper Clamp Position NOTE: Once clamped, be sure the clamps are not par- 5. Disengage the stowage straps. tially clamped to the truck bed flange. 6. Unfold Tonneau Cover to the intermediate position.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The vehicle cannot be driven when the Tonneau Cover is in this position. Fully Unfolded Position 8. Pull down on the second set of clamp handles to release the clamps from the stowed position. Intermediate Position (Vehicle Cannot Be Driven) 7. Completely unfold the Tonneau Cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 3 Stowed Position Semi Clamped Position 9. Push clamp wires up and under the flange of box (or 10. Push clamp handles upward to the clamped position flange of Ram Box rail, if equipped) to the semi to properly engage the clamps. clamped position.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Clamped Position NOTE: Once clamped, be sure the clamps are not partially clamped to the truck bed flange.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 The Tonneau Cover clamps can be locked when in the clamped position by placing a lock through the locking hole. CAUTION! It is the driver’s responsibility to ensure the Tonneau Cover is properly installed on the vehicle. Failure to follow this procedure can result in detachment of the Tonneau Cover from the vehicle and/or damage to the vehicle/Tonneau Cover.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .275 䡵 INSTRUMENT CLUSTER — MIDLINE . . . . . . .276 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . . .277 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .278 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 ▫ Electronic Vehicle Information Center (EVIC) Displays — 3.5” Display . . . . . . . . . . . . . . . .
274 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED . .353 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .353 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .354 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .355 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . . .355 䡵 RADIO OPERATION AND MOBILE PHONES . .356 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 275 INSTRUMENT PANEL FEATURES 4 1 — Headlight Switch 7 — 115v Power Inverter Outlet 2 3 4 5 6 8 — Power Outlet 9 — Lower Switch Bank 10 — Instrument Panel Drawer 11 — Climate Controls 12 — Power Outlet/Cigar Lighter — — — — — Instrument Cluster Radio Hazard Switch Upper Glove Compartment Lower Glove Compartment 13 — Gear Selector/Transfer Case Position Switch — If Equipped 14 — Ignition Switch 15 — Hood Release 16 — Parking Brake Release
276 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — MIDLINE
UNDERSTANDING YOUR INSTRUMENT PANEL 277 INSTRUMENT CLUSTER — PREMIUM 4
278 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is 1. Tachometer not functioning and that service is required. However, The tachometer indicates engine speed in Revolutions the conventional brake system will continue to operate Per Minute (RPM x 1000). normally if the BRAKE warning light is not on.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condition investigated promptly. If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service.
280 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The voltmeter may show a gauge fluctuation at • A continuous chime will sound if the vehicle is various engine temperatures. This cycling operation is driven more than 1 mile (1.6 km) with either turn caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the signal on. cycling operation is controlled by the engine control • Check for an inoperative outside light bulb if either module.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 hydraulic system malfunction or that a problem with the If brake failure is indicated, immediate repair is necessary. Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. WARNING! In this case, the light will remain on until the condition has been corrected.
282 UNDERSTANDING YOUR INSTRUMENT PANEL unless the parking brake is applied or a brake fault is 8. Seat Belt Reminder Light detected. If the light does not illuminate, have the light When the ignition switch is first turned to inspected by an authorized dealer. ON/RUN, this light will turn on for four to The light also will turn on when the parking brake is eight seconds as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 dealer as soon as possible. Refer to “Occupant Restraints” 13. Cargo Light — If Equipped in “Things To Know Before Starting Your Vehicle” for The cargo light will illuminate when the cargo further information. light is activated by pressing the cargo light 10. Oil Pressure Gauge — If Equipped button on the headlight switch. The pointer should always indicate some oil pressure when the engine is running.
284 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Tire Pressure Monitoring Telltale Light — If reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
286 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The highest available transmission gear is dis- 22. TOW/HAUL played in the lower right corner of the Electronic Vehicle The TOW HAUL button is located on the center Information Center (EVIC) whenever the Electronic stack upper switch bank. This light will illumiRange Select (ERS) feature is active. Use the +/- selector nate when TOW HAUL mode is selected. on the shift lever to activate ERS.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 The gauge pointer will likely indicate a higher tempera• The “ESC Off Indicator Light” and the “ESC ture when driving in hot weather, up mountain grades, Activation/Malfunction Indicator Light” come on or when towing a trailer. It should not be allowed to momentarily each time the ignition switch is turned exceed the upper limits of the normal operating range. to ON/RUN.
288 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle.” Follow the warnings under the “Cooling System Pressure Cap” paragraph. 26.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. 29.
290 UNDERSTANDING YOUR INSTRUMENT PANEL rotate at the same speed. Low range provides a greater 33. 4WD Indicator Light — If Equipped gear reduction ratio to provide increased torque at the This light alerts the driver that the vehicle is in wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) This system allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
292 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by • UP Arrow Button pressing the following buttons mounted on the steering Press and release the UP arrow button to scroll wheel: upward through the main menu and submenus (Fuel Economy, Trip A, Trip B, Audio, Stored Messages, Screen Set Up).
UNDERSTANDING YOUR INSTRUMENT PANEL 293 • LEFT Arrow Button Press the LEFT arrow button to return to the main menu from an info screen or sub-menu item. Electronic Vehicle Information Center (EVIC) Displays — 3.
294 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC displays are located in the center portion of the 4. EVIC White Telltales cluster and consists of seven sections: • Electronic Speed Control Ready This light will turn on when the electronic 1. Compass Display speed control is ON. For further information, Displays the current direction. For further information, refer to “Electronic Speed Control” in “Underrefer to “Compass Settings” under “Customer Programstanding The Features Of Your Vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 • Low Coolant Level Indicator • Hill Decent Control (HDC) — If Equipped The Hill Decent Control symbol indicates the This telltale will turn on to indicate the vehicle coolant level is low. status of the Hill Descent Control (HDC) feature. The lamp will be on solid when HDC is armed.
296 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. • Service Stop/Start System Telltale — If Equipped This telltale will turn on to indicate that the Stop/Start is Unavailable, service Stop/Start system.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 • Wait To Start Light — Diesel Only 6. EVIC Red Telltales The “Wait To Start” telltale will illuminate for • Door Ajar approximately two seconds when the ignition is This light will turn on to indicate that one or turned to the RUN position. It’s duration may be longer more doors may be ajar. based on colder operating conditions. Vehicle will not initiate start until telltale is out.
298 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 • Engine Temperature Warning Light This light warns of an overheated engine condition. As temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle.
300 UNDERSTANDING YOUR INSTRUMENT PANEL The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 Fuel Filter Life Reset — Diesel Only Vehicles Equipped With Passive Entry Press and release the Up EVIC screen. arrow button to exit the Without pressing the brake pedal, press the ENGINE Vehicles Not Equipped With Passive Entry START/STOP button and cycle the ignition to the ON/ Without pressing the brake pedal, press the ENGINE RUN position (Do not start the engine.
302 UNDERSTANDING YOUR INSTRUMENT PANEL arrow button to select indicator system is duty cycle based, which means the Press and release the DOWN “Reset”, then press and release the Right arrow engine oil change interval may fluctuate, dependent button to select reset of the Fuel Filter Life to upon your personal driving style. 100%. Vehicles Equipped With Passive Entry arrow button to exit the 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 4. Press and release the DOWN arrow button to select “Reset”, then press and release the Right arrow button to select reset of the Oil Life to 100%. 5. Press and release the Up EVIC screen. arrow button to exit the Vehicles Not Equipped With Passive Entry 3. Press and release the RIGHT arrow button to access the ”Oil Life” screen. 4.
304 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays — 7” Display 1. Main Screen — The inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings and white for on demand information. 2. Audio / Phone Information and Sub-menu Information — Whenever there are sub-menus available, the position within the sub-menus is shown here. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 9. Selectable Gauge 2 10. Selectable Gauge 1 11. Selectable Gauge 1 The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages. These pop up messages fall into several categories: • Five Second Stored Messages the EVIC’s compass/outside temp line.
306 UNDERSTANDING YOUR INSTRUMENT PANEL seconds and then returns to the previous screen. An • Low Coolant Level Indicator example of this message type is “Automatic High Beams This telltale will turn on to indicate the vehicle On”. coolant level is low. EVIC Amber Telltales This area will show reconfigurable amber caution tell- • Transmission Temperature Warning Telltale tales. These telltales include: This telltale indicates that the transmission • Low Fuel Telltale fluid temperature is running hot.
UNDERSTANDING YOUR INSTRUMENT PANEL 307 CAUTION! Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure. WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.
308 UNDERSTANDING YOUR INSTRUMENT PANEL • Loose Fuel Filler Cap (48 km/h). If these conditions are not met while attempting to use the HDC feature, the HDC indicator lamp will This telltale will turn on to indicate that the fuel flash on/off. filler cap may be loose.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 EVIC Red Telltales This area will show reconfigurable red telltales. These telltales include: • Door Ajar • Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. This light will turn on to indicate that one or • Charging System Light more doors may be ajar. This light shows the status of the electrical charging system.
310 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Throttle Control (ETC) Light • Engine Temperature Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. This light warns of an overheated engine condition.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 • Electric Power Steering Malfunction Warning Light Fuel Filter Life Reset — Diesel Only This telltale is on when the Electric Power Vehicles Equipped With Passive Entry Steering is not operating and needs service. 1. Without pressing the brake pedal, press the ENGINE START/STOP button and cycle the ignition to the ON/RUN position (Do not start the engine.) • Trailer Brake Disconnected Warning Light arrow button to This telltale is on when the Trailer Brake has 2.
312 UNDERSTANDING YOUR INSTRUMENT PANEL arrow button to 5. Press and release the DOWN select “Yes”, then press and release the Right arrow button to select reset of the Fuel Filter Life. 4. Press and hold the RIGHT arrow button for one second to access the ”Fuel Filter Life Reset” screen. arrow button to exit the 5. Press and release the DOWN arrow button to select “Yes”, then press and release the Right arrow button to select reset of the Fuel Filter Life.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 indicator system is duty cycle based, which means the 5. Press and release the DOWN arrow button to engine oil change interval may fluctuate, dependent select “Yes”, then press and release the Right arrow upon your personal driving style. button to select reset of the Oil Life. Vehicles Equipped With Passive Entry 6. Press and release the Up EVIC screen. arrow button to exit the 1.
314 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Press and hold the RIGHT arrow button for • Service Airbag System one second to access the ” Oil Life Reset” • Traction Control Off screen. • Washer Fluid Low arrow button to 5. Press and release the DOWN select “Yes”, then press and release the Right arrow • Oil Pressure Low button to select reset of the Oil Life. • Oil Change Due arrow button to exit the 6. Press and release the Up • Fuel Low EVIC screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 • Tire Pressure Screen With Low Tire(s) “Inflate Tire to • XX” • • Service Tire Pressure System • • Parking Brake Engaged • • Brake Fluid Low • • Service Electronic Braking System • • Engine Temperature Hot • • Battery Voltage Low • • Service Electronic Throttle Control • • Lights On • • Right Turn Signal Light Out • • Left Turn Signal Light Out • • Turn Signal On • Vehicle Not in Park Key in Ignition Key in Ignition Lights On Remote Start Active Key to Run Remote S
316 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Airbag Warning Light • Transmission Cool Ready to Drive • Driver Seatbelt Unbuckled • Trailer Brake Disconnected • Passenger Seatbelt Unbuckled • Service Transmission • Front Seatbelts Unbuckled • Service Shifter • Door Open • Engage Park Brake to Prevent Rolling • Doors Open • Transmission Too cold Idle with Engine On • Gear Not Available • Washer Fluid Low • Shift Not Allowed • Service Air Suspension System • Shift to Neutral then Drive or
UNDERSTANDING YOUR INSTRUMENT PANEL 317 • Selected Ride Height Not Permitted • Stop/Start Not Ready Battery Charging – If Equipped • Service Air Suspension System Immediately • Stop/Start Not Ready Trailer Tow/Haul Selected – If Equipped • Reduce Speed To Maintain Selected Ride Height • Air Suspension System Cooling Down Please Wait • Vehicle Cannot Be Lowered Door Open • Off Road 2 Watch For Clearance • Entry/Exit Watch For Clearance • Air Suspension Temporarily Disabled For Jacking And Tire Change •
318 UNDERSTANDING YOUR INSTRUMENT PANEL • Stop/Start Not Ready Driver Door Open – If Equipped • Stop/Start Cannot Autostart Hood Open – If Equipped • Stop/Start Not Ready Cabin Cooling Or Heating – If Equipped • Stop/Start Unavailable Service Battery – If Equipped • Stop/Start Not Ready Not Ready Max Cooling Or • Stop/Start Unavailable Service Stop/Start System – If Heating – If Equipped Equipped • Stop/Start Not Ready Max Cooling Or Heating Se- • Stop/Start To Restart Shift Out Of Park – If Equipped lecte
UNDERSTANDING YOUR INSTRUMENT PANEL 319 Digital Speedometer Air Suspension – If Equipped Transmission Temperature – Automatic Transmission Press and release the UP or DOWN arrow Only button until the Digital display icon is highOil Temp lighted in the EVIC. Press and release the SELECT/RIGHT arrow button to change the Oil Life display between km/h and mph.
320 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Pressure Information System (3500 Series Heavy Trip A Duty Ram Trucks) Press and release the UP or DOWN arrow Press and release the UP or DOWN arrow button until button until the Trip A icon is highlighted in “Tire Pressure” is highlighted in the EVIC. Press and the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 Trip B Fuel Economy Press and release Up & Down arrow button until the Trip B icon is highlighted in the EVIC. The Trip B information will display the following: Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted.
322 UNDERSTANDING YOUR INSTRUMENT PANEL Trailer Tow Screen Setup Press and release the UP or DOWN arrow Press and release the UP or DOWN arrow button until the Trailer Tow icon is highlighted. button until the Screen Setup display icon is Press the SELECT/RIGHT arrow button and highlighted in the EVIC. Press and release the the next screen will display the following SELECT/RIGHT arrow button to enter the trailer trip information: Screen Setup sub-menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 Personal Settings (Customer-Programmable Features) Press and release the SELECT/RIGHT arrow button to Enter Vehicle Settings For vehicles equipped a 3.5” EVIC screen Use the UP or DOWN button to display one of the following choices. Personal Settings allows the driver to set and recall features when the transmission is in PARK. NOTE: Your vehicle may or may not be equipped with Press and release the UP and DOWN button until Per- the following settings.
324 UNDERSTANDING YOUR INSTRUMENT PANEL Units Press and release the UP or DOWN button until “Units” displays in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure. To make your selection, press and release the SELECT button the selected setting will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 button until a check-mark appears next to the feature feature showing the system has been activated or the showing the system has been activated or the check-mark check-mark is removed showing the system has been deactivated. is removed showing the system has been deactivated. Auto Wipers — If Equipped Headlamp Off Delay When ON is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield.
326 UNDERSTANDING YOUR INSTRUMENT PANEL highlighted, then press and release the SELECT button showing the system has been activated or the check-mark until a check-mark appears next to the setting, showing is removed showing the system has been deactivated. Refer to “Lights/SmartBeam™ — If Equipped” in “Unthat the setting has been selected. derstanding The Features Of Your Vehicle” for further Headlamps With Wipers information.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 SELECT button until a check-mark appears next to the feature showing the system has been activated or the feature showing the system has been activated, or the check-mark is removed showing the system has been check-mark is removed showing the system has been deactivated. deactivated.
328 UNDERSTANDING YOUR INSTRUMENT PANEL When Unlock All Doors On 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 a check-mark appears next to the feature showing the selection, scroll up or down until the preferred setting is system has been activated or the check-mark is removed highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing showing the system has been deactivated. that the setting has been selected.
330 UNDERSTANDING YOUR INSTRUMENT PANEL the feature showing the system has been activated or the check-mark is removed showing the system has been When this feature is selected the air suspension system is deactivated. disabled to assist with flat bed towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 release the SELECT button until a check-mark appears press and release the SELECT button until a check-mark next to the setting, showing that the setting has been appears next to the setting, showing that the setting has been selected. selected. Trailer Brake Type Calibrate Compass When this feature is selected, the Trailer Brake Type can be changed between “Light Electric”, “Heavy Electric”, “Light EOH” and “Heavy EOH”.
332 UNDERSTANDING YOUR INSTRUMENT PANEL • Outside Temp (default setting) • Compass (default setting) • Trans Temp • Outside Temp • Oil Temp • Trans Temp • Time • Oil Temp • Range To Empty (RTE) • Time • Average MPG • Range To Empty (RTE) • Current MPG • Average MPG • Trip A • Current MPG • Trip B • Trip A • Trailer Trip (distance only) • Trip B • Trailer Brake Gain • Trailer Trip (distance only) Upper Right • Trailer Brake Gain • None
UNDERSTANDING YOUR INSTRUMENT PANEL 333 Lower Left • Compass • None (default setting) • Outside Temp • Compass • Trans Temp • Outside Temp • Oil Temp • Trans Temp • Time • Oil Temp • Range • Time • AVG MPG • Range • Current MPG • AVG MPG • Trailer Brake Gain • Current MPG Restore To Defaults (Restores All Settings To Default Settings) • Trailer Brake Gain Lower Right • None (default setting) • Cancel • Okay 4
334 UNDERSTANDING YOUR INSTRUMENT PANEL Press the Screen Off hard-key to turn off the Uconnect® screen. Press the Screen Off hard-key a second time to The Uconnect® system uses a combination of soft and turn the screen on. hard keys located on the center of the instrument panel that allows you to access and change the customer Press the Back hard-key to exit out of a Menu or certain option on the Uconnect® system. programmable features.
UNDERSTANDING YOUR INSTRUMENT PANEL 335 Comfort & Remote Start, Engine Off Operation, Compass • Display Mode Settings, Audio, Phone/Bluetooth® and SiriusXM Setup. When in this display you may select one of the auto NOTE: Only one touchscreen area may be selected at a display settings. To change Mode status, touch and release the “Day.” “Night” or “Auto” soft-key. Then time. touch the back arrow soft-key. When making a selection, touch the soft-key to enter the desired mode.
336 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Language • Voice Response Length When in this display, you may select one of three languages for all display nomenclature, including the trip functions and the navigation system (if equipped). Touch the “Set Language” soft-key and then touch the desired language soft-key until a check-mark appears next to the language, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 designated turn within a programmed route. To make your selection, touch the “Navigation Turn-By-Turn In Cluster” soft-key, until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. • Fuel Saver Display In Cluster The “ECO” message is located in the instrument cluster display, this message can be turned on or off.
338 UNDERSTANDING YOUR INSTRUMENT PANEL make your selection, touch the “+” or “–” soft-keys to adjust the minutes up or down. Touch the back arrow soft-key to return to the previous menu or touch the “X” soft-key to close out of the settings screen. • Time Format (18 km/h). The system can be enabled with Sound Only or Sound and Display. To change the Park Assist status, touch and release the “Sound Only” or the “Sounds and Display” soft-key. Then touch the back arrow soft-key.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 • ParkView® Backup Camera the “ParkView® Backup Camera Delay” soft-key, until a check-mark appears next to the setting, indicating that Your vehicle may be equipped with the ParkView® Rear the setting had been selected. Touch the back arrow Back Up Camera that allows you to see an on-screen soft-key to return to the previous menu. image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE.
340 UNDERSTANDING YOUR INSTRUMENT PANEL • ParkView® Backup Camera Fixed Guidelines Your vehicle may be equipped with the ParkView® Rear Back Up Camera Fixed Guidelines that allows you to see Fixed Guidelines over the ParkView Back up Camera display whenever the shift lever is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds, this note will disappear.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 • ParkSense® Rear Park Assist Chime Volume • Hill Start Assist — If Equipped Rear Park Assist chime volume settings can be selected from the EVIC or Uconnect® System (if equipped). The chime volume settings include LOW, MEDIUM, and HIGH. The factory default volume setting is MEDIUM. When this feature is selected, the Hill Start Assist (HSA) system is active.
342 UNDERSTANDING YOUR INSTRUMENT PANEL dealer for information. Protection Mode will automati- • Headlight Illumination On Approach cally be selected to “protect” the air suspension system When this feature is selected, the headlights will activate when the payload has been exceeded or load leveling and remain on for 0, 30, 60, or 90 seconds when the doors cannot be achieved. are unlocked with the Remote Keyless Entry (RKE) Lights transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 • Auto Dim High Beams “SmartBeam™” — If Equipped • Flash Headlights With Lock When this feature is selected, the high beam headlights will deactivate automatically under certain conditions. To make your selection, touch the Auto High Beams softkey, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
344 UNDERSTANDING YOUR INSTRUMENT PANEL soft-key, until a check-mark appears next to setting, showing the system has been activated or the check-mark showing that setting has been selected. Touch the back is removed showing the system has been deactivated. arrow soft-key to return to the previous menu. • Sound Horn With Lock • Auto Unlock On Exit When this feature is selected, the horn will sound when When this feature is selected, all doors will unlock when the door locks are activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 • 1st Press Of Key Fob Unlocks When 1st Press Of Key Fob Unlocks is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When 1st Press Of Key Fob Unlocks is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When Unlock All Doors On 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
346 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the Remote Keyless Entry (RKE) transmitter is used to unlock the door. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information. • Auto-On Driver Heated/Ventilated Seat & Steering Wheel With Vehicle Start — If Equipped When this feature is selected, the horn will sound when the remote start is activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 To make your selection, touch the Easy Exit Seats soft- Delay status touch the + or - soft-key to select your key, until a check-mark appears next to setting, showing desired time interval. Touch the back arrow soft-key to that setting has been selected. Touch the back arrow return to the previous menu. soft-key to return to the previous menu.
348 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials, such as iPod’s®, Mobile Phones, Laptops and Radar Detectors, away from the top of the instrument panel where the compass module is located. These materials can cause interference with the compass sensor, and it may give false readings. • Perform Compass Calibration Touch the “Calibration” soft-key to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 • Equalizer • Surround Sound — If Equipped When in this display you may adjust the Bass, Mid and Treble settings. Adjust the settings with the “+” and “–” soft-keys or by selecting any point on the scale between the “+” and “–” soft-keys. Then touch the back arrow soft-key. This feature provides simulated surround sound mode. To make your selection, touch the “Surround Sound” soft-key, select On or Off followed by pressing the back arrow soft-key.
350 UNDERSTANDING YOUR INSTRUMENT PANEL Trailer Brake • Trailer Name • Trailer Select When this feature is selected, the Trailer name can be selected from 16 names. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 Air Suspension — If Equipped system has been activated or the check-mark is removed showing the system has been deactivated. After pressing the “Suspension” soft-key the following • Suspension Display Messages settings will be available. • Sound Horn With Remote Lower When All is selected, all the Air Suspension Alerts will be When this feature is selected, a short horn sound will displayed.
352 UNDERSTANDING YOUR INSTRUMENT PANEL to the feature showing the system has been activated or • Channel Skip the check-mark is removed showing the system has been SiriusXM can be programmed to designate a group of deactivated. channels that are the most desirable to listen to or to • Transport Mode exclude undesirable channels while scanning.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 Write down the SIRIUS ID numbers for your receiver. To may not fully support the iPod® control features. Please reactivate your service, either call the number listed on visit Apple’s website for software updates. the screen or visit the provider online. For further information, refer to the Uconnect® SuppleNOTE: SiriusXM Travel Link is a separate subscription ment Manual. and is available for U.S. residents only.
354 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the right hand control will switch modes to Radio, CD or other valid audio sources. The left hand control is a rocker type switch with a pushbutton in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 CD Player 3. Do not apply paper or tape to the disc; avoid scratching the disc. Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once 4. Do not use solvents such as benzene, thinner, cleaners, will go to the beginning of the current track or to the or anti-static sprays. beginning of the previous track if it is within eight 5. Store the disc in its case after playing.
356 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND MOBILE PHONES Manual Climate Controls Without Touchscreen — Under certain conditions, the mobile phone being on in If Equipped your vehicle can cause erratic or noisy performance from The controls for the manual heating and air conditioning your radio. This condition may be lessened or eliminated system in this vehicle consist of a series of outer rotary by relocating the mobile phone antenna. This condition is dials and inner push knobs.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position.
358 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For vehicles equipped with Remote Start, the Air Conditioning Operation climate controls will not function during Remote Start operation if the blower control is left in the OFF position. Push the A/C button to engage the Air Conditioning (A/C). A LED will illuTemperature Control minate when the A/C system is engaged. Use this control to regulate the temperature of the air inside the passenger compartment.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 NOTE: A/C cannot be deselected when in MAX A/C position. The LED will blink three times if the A/C button is pushed. If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser.
360 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode with maximum blower and warm temperature settings for best windshield and side window defrosting. Air is directed through the floor outlets with a NOTE: The air conditioning compressor operates in MIX small amount through the defrost and side win- and DEFROST, or a blend of these modes even if the A/C dow demist outlets. button is not pressed. This dehumidifies the air to help dry the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 NOTE: Air Outlets • If the RECIRCULATION button is pressed when the system is in Defrost mode, the Recirculation LED indicator will flash three times and then turn off to indicate Recirculation mode is not allowed. The airflow from each of the instrument panel outlets can be adjusted for direction, and turned on or off to control airflow.
362 UNDERSTANDING YOUR INSTRUMENT PANEL Stop/Start System — If Equipped Manual Climate Controls With Touchscreen — If While in an Autostop, the Climate Controls system may Equipped automatically adjust airflow to maintain cabin comfort. Hard-Keys Customer settings will be maintained upon return to an The hard-keys are located below the radio touchscreen. engine running condition.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Soft-Keys Soft-keys are accessible on the radio touchscreen. Button Descriptions (Applies To Both Hard-Keys And Soft-Keys) 1. MAX A/C Button Press and release to toggle between MAX A/C and the prior settings. The soft-key illuminates when MAX A/C is ON. In MAX A/C, the blower level and mode position can be adjusted to desired user settings.
364 UNDERSTANDING YOUR INSTRUMENT PANEL equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster Press and release to change the current setting; the automatically turns off after 10 minutes. indicator illuminates when ON. 3. Recirculation Button 4. Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is ON. Air comes from the windshield and side window demist outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 6. Modes The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, demister outlets and defrost outlets. The Mode settings are as follows: • Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
366 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Blower Control 8. Climate Control OFF Button Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation. The speeds can be selected using either hard-keys or soft-keys as follows: Press and release this button to turn the Climate Control ON/OFF. Hard-Key 9.
UNDERSTANDING YOUR INSTRUMENT PANEL 367 pressing the RECIRCULATION control button. Recirculation mode should only be used temporarily. The recirculation LED will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the Recirculation mode LED and allow outside air into the vehicle. Automatic Climate Controls With Touchscreen — If Equipped Hard-Keys The hard-keys are located below the Uconnect® screen.
368 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Uconnect® 8.4 Automatic Temperature Controls — Soft-Keys Uconnect® 5.0 Automatic Temperature Controls — Soft-Keys Button Descriptions (Applies To Both Hard-Keys And Soft-Keys) 1. MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 369 this function again will cause the MAX A/C operation to 5. Front Defrost Button switch into manual mode and the MAX A/C indicator Press and release to change the current airflow setting to will turn off. Defrost mode. The indicator illuminates when this fea2. A/C Button ture is ON. Air comes from the windshield and side window demist outlets. When the defrost button is Press and release to change the current setting, the selected, the blower level will increase.
370 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 9. SYNC Soft-Key Press the Sync soft-key to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger temperature setting with the driver temperature setting. Changing the passenger temperature setting while in Sync will automatically exit this feature. Use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting.
372 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Climate Control OFF Button • Bi-Level Mode Air comes from the instrument panel outlets and Press and release this button to turn the Climate Control floor outlets. A slight amount of air is directed ON/OFF. through the defrost and side window demister outlets. 13.
UNDERSTANDING YOUR INSTRUMENT PANEL 373 settings or on the touchscreen, press and slide the softkey temperature bar towards the red arrow soft-key for warmer temperature settings. NOTE: In Sync mode, this button will also automatically adjust the passenger temperature setting at the same time. 15. Temperature Control (Uconnect® 5.0) the desired temperature is displayed, the system will achieve and automatically maintain that comfort level. 3.
374 UNDERSTANDING YOUR INSTRUMENT PANEL on low until the engine warms up. The blower will Controls, the recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculaincrease in speed and transition into Auto mode. tion will be disabled automatically if this mode is seRecirculation Control lected. Attempting to use Recirculation while in this mode will cause the LED in the control button to blink When outside air contains smoke, odors, or and then turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 Procedures” in “Maintaining Your Vehicle” for proper the front blower speed. Do not use the Recirculation coolant selection. Use of the air Recirculation mode mode without A/C for long periods, as fogging may during Winter months is not recommended because it occur. may cause window fogging. NOTE: Automatic Temperature Controls (ATC) will automatically adjust the climate control settings to reduce Vacation/Storage or eliminate window fogging on the front windshield.
376 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .384 ▫ Automatic Mode . . . . . . . . . . . . . . . . . . . . . .389 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .384 ▫ Possible Reasons The Engine Does Not AUTO STOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 ▫ Automatic Transmission . . . . . . . . . . . . . . . .385 ▫ Keyless Enter-N-Go™ . . . . . . . . . . . . . . . . . .385 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . .
378 STARTING AND OPERATING ▫ Brake/Transmission Shift Interlock System . . .396 ▫ Electronically Shifted Transfer Case (Five-Position Switch) — If Equipped . . . . . . . . . . . . . . . . .444 ▫ Eight-Speed Automatic Transmission — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .397 䡵 AIR SUSPENSION SYSTEM (1500 MODELS ONLY) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . .451 ▫ Six-Speed Automatic Transmission — ▫ Description . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 379 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .461 ▫ Vehicle Recovery . . . . . . . . . . . . . . . . . . . . . .479 䡵 AXLE LOCKER SYSTEM — POWER WAGON MODELS ONLY — (IF EQUIPPED) . . . . . . . . . .461 ▫ After Driving Off-Road . . . . . . . . . . . . . . . . .483 䡵 LIMITED-SLIP DIFFERENTIAL . . . . 䡵 STABILIZER/SWAY BAR SYSTEM — POWER 䡵 DRIVING ON SLIPPERY SURFACES WAGON ONLY . . . . . . . . . . . . . . . . . . . . . . . .464 ▫ Acceleration . . . . . . . .
380 STARTING AND OPERATING ▫ Things To Know Before Using Your Winch. . . .490 ▫ Understanding The Features Of Your Winch. . .492 ▫ Winch Accessories . . . . . . . . . . . . . . . . . . . .494 ▫ Operating Your Winch . . . . . . . . . . . . . . . . . .495 ▫ Rigging Techniques . . . . . . . . . . . . . . . . . . . .507 䡵 POWER STEERING — 1500 MODELS . . . . . . . .509 䡵 POWER STEERING — 2500/3500 MODELS . . . .510 ▫ Power Steering Fluid Check — 2500/3500 Models . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 381 ▫ Tire Identification Number (TIN). . . . . . . . . . .533 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .549 ▫ Tire Terminology And Definitions . . . . . . . . . .534 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . .550 ▫ Tire Loading And Tire Pressure . . . . . . . . . . .535 䡵 SUPPLEMENTAL TIRE PRESSURE INFORMATION — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . .551 䡵 TIRES — GENERAL INFORMATION . . . . . . . .
382 STARTING AND OPERATING 䡵 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . .568 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . .574 ▫ 3.6L/6.4L Engine . . . . . . . . . . . . . . . . . . . . . .568 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . .574 ▫ 5.7L Engines . . . . . . . . . . . . . . . . . . . . . . . . .568 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles . . . . . . . . . . . . .575 ▫ Reformulated Gasoline . . . . . . . . . . .
STARTING AND OPERATING 383 ▫ Common Towing Definitions . . . . . . . . . . . . .582 ▫ 1500 Models Only . . . . . . . . . . . . . . . . . . . . .601 ▫ Trailer Hitch Type and Maximum Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .585 ▫ 2500/3500 Models Only . . . . . . . . . . . . . . . . .602 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . . .586 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . .589 ▫ Towing Requirements . .
384 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING 385 Automatic Transmission Start the engine with the shift lever in the NEUTRAL or PARK. Apply the brake before shifting into any driving range. NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be pressed to shift out of PARK. Keyless Enter-N-Go™ This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Start/Keyless Enter-N-Go™ Key Fob is in the passenger compartment.
386 STARTING AND OPERATING 4. If you wish to stop the cranking of the engine prior to the engine starting, press the button again. NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. To Turn Off The Engine Using ENGINE START/STOP Button position.
STARTING AND OPERATING 387 START. To change the ignition switch positions without If Engine Fails To Start starting the vehicle and use the accessories follow these If the engine fails to start after you have followed the steps: “Normal Starting” procedure, it may be flooded. Push 1. Starting with the ignition in the OFF position: the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any 2.
388 STARTING AND OPERATING WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
STARTING AND OPERATING 389 STOP/START SYSTEM — IF EQUIPPED To Activate The Autostop Mode, The Following Must Occur: The Stop/Start function is developed to save fuel and reduce emissions. The system will stop the engine auto- 1. The system must be in STOP/START READY state. A matically during a vehicle stop if the required conditions STOP/START READY message will be displayed in are met. Releasing the brake pedal will automatically the Electronic Vehicle Information Center (EVIC) re-start the vehicle.
390 STARTING AND OPERATING Autostop, the Climate Controls system may automati- • Cabin heating or cooling is in process and an acceptable cabin temperature has not been achieved cally adjust airflow to maintain cabin comfort. Customer settings will be maintained upon return to an engine • HVAC is set to full defrost mode at a high blower running condition.
STARTING AND OPERATING 391 • Low brake vacuum (e.g. after several brake pedal applications) While in DRIVE the engine will start when the brake pedal is released or the throttle pedal is depressed. The • STOP/START OFF switch is pressed transmission will automatically reengage upon engine restart. During this transition the brakes will hold the • 4WD system is put into 4LO mode vehicle to avoid undesired vehicle movement.
392 STARTING AND OPERATING The engine may then be restarted by moving the transmission shift selector out of PARK (e.g. to DRIVE) or, in some cases, only by a KEY START. The Electronic Vehicle Information Center (EVIC) will display a SHIFT OUT OF PARK message, or a STOP/START KEY START REQUIRED message, to indicate which action is required. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. To Manually Turn Off The Stop Start System 1.
STARTING AND OPERATING 393 3. At the next vehicle stop (after turning off the STOP/ STOP/START SYSTEM message will appear in the Electronic Vehicle Information Center (EVIC). Refer to “ElecSTART system) the engine will not be stopped. tronic Vehicle Information Center (EVIC)” in “Under4. If the STOP/START system is manually turned off, the standing Your Instrument Panel” for further information.
394 STARTING AND OPERATING 2500/3500 Models AUTOMATIC TRANSMISSION The engine block heater cord is routed through the grille by the right front tow hook. It includes a removable cap that is secured by a tethered strap. It also has a c-clip that is used for storage when not in use for the winter months. During winter months, remove the heater cord wiring assembly from itself on the c-clip. The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine.
STARTING AND OPERATING 395 WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
396 STARTING AND OPERATING WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
STARTING AND OPERATING 397 In 8-speed vehicles, the brake pedal must also be pressed The electronically-controlled transmission provides a to shift from NEUTRAL into DRIVE or REVERSE when precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new the vehicle is stopped or moving at low speeds. vehicle may be somewhat abrupt.
398 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. PARK (P) This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
STARTING AND OPERATING 399 NOTE: On four-wheel drive vehicles be sure that the transfer case is in a drive position. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not in PARK. Make sure the transmission is in PARK before leaving the vehicle.
400 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the key fob.
STARTING AND OPERATING 401 CAUTION! • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • Before moving the gear selector out of PARK, you must start the engine, and also press the brake pedal. Otherwise, damage to the gear selector could result.
402 STARTING AND OPERATING CAUTION! (Continued) severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information. (ERS) Operation⬙ in this section) to select a lower gear range. Under these conditions, using a lower gear range will improve performance and extend transmission life by reducing excessive shifting and heat buildup.
STARTING AND OPERATING 403 restarted. The Malfunction Indicator Light (MIL) may be 4. Wait approximately 30 seconds. illuminated. A message in the instrument cluster will 5. Restart the engine. inform the driver of the more serious conditions, and indicate what actions may be necessary. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal In the event of a momentary problem, the transmission operation.
404 STARTING AND OPERATING transmission is in DRIVE. For example, if you shift the transmission into 3 (third gear), the transmission will not shift above third gear (except to prevent engine overspeed), but will shift down into second and first gears normally. You can switch between DRIVE and ERS mode at any vehicle speed. When the gear selector is in DRIVE, the transmission will operate automatically, shifting between all available gears.
STARTING AND OPERATING 405 WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. When to Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode.
406 STARTING AND OPERATING the default at engine start-up. If TOW/HAUL mode is self-calibrating; therefore, the first few shifts on a new desired, the switch must be pressed each time the engine vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few is started. hundred miles (kilometers).
STARTING AND OPERATING 407 When parking on a hill, apply the parking brake before shifting the transmission to PARK, otherwise the load on DO NOT race the engine when shifting from PARK or the transmission locking mechanism may make it diffiNEUTRAL into another gear range. cult to move the shift lever out of PARK. As an added NOTE: After selecting any gear range, wait a moment to precaution, turn the front wheels toward the curb on a allow the selected gear to engage before accelerating.
408 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released. Make sure the transmission is in PARK before leaving the vehicle. • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.
STARTING AND OPERATING 409 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
410 STARTING AND OPERATING • Release the shift lever and make sure it is fully seated in the PARK gate. • Look at the transmission gear position display and verify that it indicates the PARK position. • With brake pedal released, verify that the shift lever will not move out of PARK. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
STARTING AND OPERATING 411 DRIVE (D) This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission automatically upshifts through underdrive first and second gears, direct third gear and overdrive fourth and fifth gears. The DRIVE position provides optimum driving characteristics under all normal operating conditions.
412 STARTING AND OPERATING (when stopped in heavy traffic) can help to reduce this Mode is activated. In this mode, the transmission remains in direct gear regardless of which forward gear is seexcess heat generation. lected. PARK, REVERSE, and NEUTRAL will continue to During cold temperatures, transmission operation may operate. The Malfunction Indicator Light (MIL) may be be modified depending on engine and transmission illuminated.
STARTING AND OPERATING 413 6. Shift into the desired gear range. If the problem is no Use of ERS (or TOW/HAUL mode) also enables an longer detected, the transmission will return to normal additional underdrive gear which is not normally used operation. during through-gear accelerations. This additional gear can improve vehicle performance and cooling capability NOTE: Even if the transmission can be reset, we recomwhen towing a trailer on certain grades.
414 STARTING AND OPERATING down (-) will shift the transmission down to ERS 3 (the added underdrive gear). Once in ERS mode, tapping ERS (-) or (+) will change the top available gear. Console Shift Lever Column Shift Lever To exit ERS mode, simply press and hold the shift lever to the right (+) (console shift) or press the ERS (+) switch (column shift) until “D” is once again displayed in the instrument cluster.
STARTING AND OPERATING 415 WARNING! CAUTION! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. When using ERS for engine braking while descending steep grades, be careful not to overspeed the engine. Apply the brakes as needed to prevent engine overspeed.
416 STARTING AND OPERATING • the TOW/HAUL switch has not been activated. When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
STARTING AND OPERATING 417 WARNING! NOTE: • The torque converter clutch will not engage, and the transmission will not shift into the top overdrive gear, until the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because top gear is disabled, and the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting properly when cold. This is normal.
418 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when The transmission gear position display (located in the instrument cluster) indicates the transmission gear range. shifting between these gears. The shift lever is mounted on the right side of the steering The transmission shift lever has only PARK, REVERSE, column.
STARTING AND OPERATING 419 PARK (P) This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake.
420 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
STARTING AND OPERATING 421 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
422 STARTING AND OPERATING • Release the shift lever and make sure it is fully seated in the PARK gate. • Look at the transmission gear position display and verify that it indicates the PARK position. • With brake pedal released, verify that the shift lever will not move out of PARK. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
STARTING AND OPERATING 423 If the transmission temperature exceeds normal operating limits, the powertrain controller will modify the This range should be used for most city and highway transmission shift schedule and expand the range of driving. It provides the smoothest upshifts and downtorque converter clutch engagement. This is done to shifts, and the best fuel economy. The transmission prevent transmission damage due to overheating.
424 STARTING AND OPERATING During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of both the torque converter clutch and the top overdrive gear are inhibited until the transmission fluid is warm (refer to the “Note” under “Torque Converter Clutch” in this section).
STARTING AND OPERATING 425 NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. activate ERS mode, display the current gear in the instrument cluster, and maintain that gear as the top available gear. Once in ERS mode, tapping ERS (-) or (+) will change the top available gear.
426 STARTING AND OPERATING To exit ERS mode, simply press and hold the ERS (+) switch until “D” is once again displayed in the instrument cluster. WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. CAUTION! When using ERS for engine braking while descending steep grades, be careful not to overspeed the engine. Apply the brakes as needed to prevent engine overspeed.
STARTING AND OPERATING 427 • The engine coolant has reached an adequate temperature. • Vehicle speed is sufficiently high. • The TOW/HAUL switch has not been activated. When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
428 STARTING AND OPERATING WARNING! NOTE: • The torque converter clutch will not engage, and the transmission will not shift to sixth gear, until the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because sixth gear is disabled, and engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting properly when cold. This is normal.
STARTING AND OPERATING 429 cause damage to the transmission. The torque con- • Four-wheel drive low range (4L) verter will refill within five seconds after starting the This transfer case is intended to be driven in the 2H engine. position for normal street and highway conditions such as dry, hard surfaced roads. FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED Four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case.
430 STARTING AND OPERATING in four-wheel drive and that the front and rear driveshafts are locked together. This light will illuminate when the transfer case is shifted into either the 4H or 4L position. There is no light for the 2H or NEUTRAL positions on some models. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
STARTING AND OPERATING 431 For additional information on the appropriate use of each 4L transfer case mode position, see the information below: Four-Wheel Drive Low Range — This range locks the front and rear driveshafts together forcing the front and 2H rear wheels to rotate at the same speed. Additional Rear-Wheel Drive High Range — This range is for traction and maximum pulling power for loose, slippery normal street and highway driving on dry hard surfaced road surfaces only.
432 STARTING AND OPERATING vehicle in motion, the transfer case will engage/ • Shifting into or out of 4L is possible with the vehicle disengage faster if you momentarily release the acceleracompletely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. tor pedal after completing the shift. Apply a constant Several attempts may be required for clutch teeth force when shifting the transfer case lever. alignment and shift completion to occur.
STARTING AND OPERATING 433 Electronically Shifted Transfer Case (Four-Position Switch) — If Equipped This electronically shifted transfer case provides four mode positions: This is an electronic shift transfer case and is operated by • Two-wheel drive high range (2WD) the 4WD Control Switch (Transfer Case Switch), which is • Four-wheel drive lock range (4WD LOCK) located on the instrument panel.
434 STARTING AND OPERATING and 4WD LOW positions are designed for loose, slippery If All Shift Conditions Are Met: road surfaces only. Driving in the 4WD LOCK and 4WD 1. The current position indicator light will turn OFF. LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline compo- 2. The selected position indicator light will flash until the transfer case completes the shift. nents. NOTE: The transfer case NEUTRAL position is selected 3.
STARTING AND OPERATING 435 NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection. To find the shift requirements, refer to the ⬙Shifting Procedure⬙ for your transfer case, located in this section. The “SVC 4WD Warning Light” monitors the electronic shift four-wheel drive system.
436 STARTING AND OPERATING Because four-wheel drive provides improved traction, 2WD there is a tendency to exceed safe turning and stopping Rear Wheel Drive High Range — This range is for normal speeds. Do not go faster than road conditions permit. street and highway driving on dry, hard surfaced roads. WARNING! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
STARTING AND OPERATING 437 NEUTRAL (N) Neutral — This range disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “Recreational Towing” in “Starting and Operating” for further information. Shifting Procedure NOTE: • If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.
438 STARTING AND OPERATING NOTE: The four-wheel drive system will not allow shifts 2. Shift the transmission into NEUTRAL. between 2WD/4WD LOCK if the front and/or rear 3. While still rolling, rotate the transfer case control wheels are spinning (no traction). In this situation, the switch to the desired position. selected position indicator light will flash and the original position indicator light will remain ON. At this time, 4.
STARTING AND OPERATING 439 NOTE: • If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift, then the desired position indicator light will flash continuously while the original position indicator light is ON, until all requirements have been met. • The ignition switch must be in the ON position for a shift to take place and for the position indicator lights to be operable.
440 STARTING AND OPERATING • Four-wheel drive low range (4WD LOW) • Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two–wheel drive position (2WD) or fourwheel drive position (4WD AUTO) for normal street and highway conditions on dry hard surfaced roads). Driving the vehicle in 2WD will have greater fuel economy benefits as the front axle is not engaged in 2WD. For variable driving conditions, the 4WD AUTO mode can be used.
STARTING AND OPERATING 441 cluster and indicate the current and desired transfer case NOTE: Before retrying a selection, make certain that all selection. When you select a different transfer case posi- the necessary requirements for selecting a new transfer tion, the indicator lights will do the following: case position have been met. To retry the selection, turn the control knob back to the current position, wait five If All Shift Conditions Are Met: seconds, and retry selection.
442 STARTING AND OPERATING WARNING! (Continued) allow the vehicle to roll which may cause personal injury or death. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. This could cause damage to driveline components. When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD, 4WD AUTO or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h).
STARTING AND OPERATING 443 For additional information on the appropriate use of each 4WD LOW transfer case mode position, see the information below: Four-Wheel Drive Low Range - This range provides low 2WD speed four-wheel drive. It maximizes torque to the front driveshaft , forcing the front and rear wheels to rotate at Rear-Wheel Drive High Range - This range is for normal the same speed. This range provides additional traction street and highway driving on dry hard surfaced roads.
444 STARTING AND OPERATING Shifting Procedure NOTE: Electronically Shifted Transfer Case (Five-Position Switch) — If Equipped This is an electronic shift transfer case and is operated by • If any of the requirements to select a new transfer case the 4WD Control Switch (Transfer Case Switch), which is position have not been met, the transfer case will not located on the instrument panel. shift.
STARTING AND OPERATING 445 This electronically shifted transfer case provides five drive will be automatically engaged when the vehicle mode positions: senses a loss of traction. Because the front axle is engaged, this mode will result in lower fuel economy than • Two-wheel drive high range (2WD) the 2WD mode.
446 STARTING AND OPERATING NOTE: The transfer case NEUTRAL position is selected by depressing the recessed button (with a ballpoint pen or similar object) located in the center of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational Towing” in “Starting and Operating” for further information.
STARTING AND OPERATING 447 after engine start up or illuminates during driving, it AUTO or 4WD LOCK positions at a given road speed. means that the four-wheel drive system is not function- Take care not to overspeed the engine and do not exceed ing properly and that service is required. 25 mph (40 km/h). WARNING! Always engage the parking brake when powering down the vehicle if the “SVC 4WD Warning Light” is illuminated.
448 STARTING AND OPERATING WARNING! (Continued) disengages both the front and rear drive shafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle. 4WD LOCK Four-Wheel Drive Lock Range - This range maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only.
STARTING AND OPERATING 449 towing behind another vehicle. Refer to “Recreational 2WD To 4WD AUTO Or 4WD LOCK Towing” in “Starting and Operating” for further inforPress the desired position on the 4WD Control Switch to mation. shift the transfer case. Shifts between 2WD and 4WD AUTO and 4WD LOCK can be done with the vehicle Shifting Procedure stopped or in motion.
450 STARTING AND OPERATING Preferred Procedure 4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear. 1. With the engine running, slow the vehicle to 2 to 3 mph (3 to 5 km/h). NOTE: • If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift 3. While still rolling, press the desired position on the or if they no longer are being met while the shift transfer case control switch.
STARTING AND OPERATING 451 AIR SUSPENSION SYSTEM (1500 MODELS ONLY) — IF EQUIPPED Description The air suspension system provides full time load leveling capability along with the benefit of being able to adjust vehicle height by the push of a button.
452 STARTING AND OPERATING NOTE: The vehicle will automatically enter Aero Mode when the vehicle speed remains between 62 mph (100 km/h) and 66 mph (106 km/h) for greater than 20 seconds or if the vehicle speed exceeds 66 mph (106 km/h). will be automatically lowered to NRH. Off-Road 1 may not be available due to vehicle payload, an EVIC message will be displayed when this occurs. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
STARTING AND OPERATING 453 • If the vehicle is in OFFROAD1 or OFFROAD2 setting, be aware of your surroundings, you may not have the clearance required for certain areas and vehicle damage may occur. NOTE: Automatic Aero Mode may be disabled through vehicle settings in the Electronic Vehicle Information Center (EVIC) when equipped with Uconnect 3.0, or your Uconnect® Radio when equipped with UConnect® 5.0, 8.4A, or 8.4AN. • Aero Mode (Lowers the vehicle approximately .
454 STARTING AND OPERATING 15 mph (24 km/h). Entry/Exit mode may not be available due to vehicle payload, an EVIC message will be displayed when this occurs. Refer to ⬙Electronic Vehicle Information Center (EVIC)⬙ in ⬙Understanding Your Instrument Panel⬙ for further information. must be closed. If a door is opened at any time while the vehicle is lowering the change will not be completed until the open door(s) is closed.
STARTING AND OPERATING 455 NOTE: If equipped with a touch screen radio all enabling/disabling of air suspension features must be done through the radio. Refer to “Uconnect® Access Settings” in “Understanding Your Instrument Panel” for further information. WARNING! The air suspension system uses a high pressure volume of air to operate the system. To avoid personal injury or damage to the system, see your authorized dealer for service. Air Suspension Modes to be disabled.
456 STARTING AND OPERATING Settings” in “Understanding Your Instrument Panel” for Before performing a wheel alignment this mode must be further information. enabled. Refer to “Electronic Vehicle Information Center Electronic Vehicle Information Center (EVIC) (EVIC)” in “Understanding Your Instrument Panel” for Display Messages further information. When the appropriate conditions exist, a message will NOTE: This mode is intended to be enabled with engine appear in the EVIC display.
STARTING AND OPERATING 457 multiple indicators are flashing, the lowest solid indica- Automatic height changes will occur based on vehicle tor lamp is the position the system is working to achieve. speed and the current vehicle height. The indicator lamps and EVIC messages will operate the same for automatic Pressing the “UP” button once will move the suspension changes and user requested changes. one position higher from the current position, assuming all conditions are met (i.e.
458 STARTING AND OPERATING • Transport Mode – No indicator lamps will be illuminated. Transport Mode is disabled by driving the vehicle. • Tire/Jack Mode – indicator lamps 3 and 6 will be illuminated. Tire/Jack Mode is disabled by driving the vehicle. • Wheel Alignment Mode – indicator lamps 3 and 4 will be illuminated. Wheel Alignment Mode is disabled by driving the vehicle.
STARTING AND OPERATING 459 including towing a trailer. The trailer button will blink continuously until trailer height has been achieved. WARNING! The system requires that the ignition be in ON/RUN position or the engine running for all user requested changes. The air suspension system uses a high pressure volume of air to operate the system. To avoid personal injury or damage to the system, see your authorized dealer for service.
460 STARTING AND OPERATING NOTE: This mode is intended to be enabled with engine NOTE: This mode is intended to be enabled with engine running. running. Transport Mode Protection Mode To assist with flat bed towing, the air suspension system has a feature which will put the vehicle below Normal Ride Height (NRH) and disable the automatic load leveling system. This mode is intended to be used with engine running.
STARTING AND OPERATING 461 Electronic Vehicle Information Center (EVIC) Display Messages NOTE: The LED will continuously blink until Normal Ride Height (NRH) has been achieved. When the appropriate conditions exist, a message will • Transport Mode – No indicator lamps will be illumiappear in the EVIC display. Refer to “Electronic Vehicle nated. Transport Mode is disabled by driving the Information Center (EVIC)” in “Understanding Your vehicle. Instrument Panel” for further information.
462 STARTING AND OPERATING stuck. The locking front and rear differentials should only be engaged during low-speed, extreme off-road situations where one wheel is likely to not be in contact with the ground. It is not recommended to drive the vehicle with the differentials locked on pavement due to the reduced ability to turn and speed limitations. CAUTION! • Do not lock the front or rear axle on hard surfaced roads.
STARTING AND OPERATING 463 To lock the rear axle, place the vehicle in 4LO. Refer to “Four Wheel Drive Operation” in “Starting and Operating” for further information. Move the axle locker switch position to REAR LOCK while traveling less than 3 mph (5 km/h). The RR indicator light will remain on when the rear axle is locked. NOTE: Left to right wheel speed difference may be necessary to allow the axle to fully lock.
464 STARTING AND OPERATING To unlock the rear axle; move the axle locker switch to AXLE UNLOCK. The REAR LOCK indicator light will go out when the rear axle is unlocked. STABILIZER/SWAY BAR SYSTEM — POWER WAGON ONLY Your vehicle is equipped with an electronic disconnecting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. Due to the use of taller springs, this vehicle has an increased ride height of approximately 1.9 in (48.3 mm) in the front and 1.5 in (38.
STARTING AND OPERATING 465 The switch has two positions; On-Road and Off-Road. The system is normally in the On-Road mode, indicated by a solid green light. The stabilizer/sway bar should remain in the On-Road mode during normal driving conditions. WARNING! Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result in serious injury or death.
466 STARTING AND OPERATING WARNING! If the stabilizer/sway bar will not return to On-Road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury or death. Contact your local service center for assistance. agency to determine the designated off-road vehicle (ORV) trails or recreation areas.
STARTING AND OPERATING 467 ramp without lifting any other wheel off the ground. This CAUTION! distance up the ramp divided by the wheelbase of the vehicle and multiplied by 1,000 is the RTI. This vehicle The door sill height is 25 inches. Water may intrude has an RTI of 655, which means you can articulate one into the interior of the vehicle at greater depths. front wheel 32 inches in the air while the other three Simultaneous Brake And Throttle Operation wheels remain in contact with the ground.
468 STARTING AND OPERATING mud, snow and ice. Every surface has a different effect on your vehicle’s steering, handling and traction. Controlling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel and maintain a good driving posture. Avoid sudden accelerations, turns or braking. In most cases there are no road signs, posted speed limits or signal lights. Therefore you will need to use your own good judgment on what is safe and what isn’t.
STARTING AND OPERATING 469 Driving In Snow, Mud And Sand CAUTION! There is a drastic reduction in traction when driving in On icy or slippery roads, do not downshift at high snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore you engine RPMs or vehicle speeds because engine brakshould accelerate slowly, leave greater stopping distances ing may cause skidding and loss of control. and avoid abrupt vehicle maneuvers.
470 STARTING AND OPERATING • Sand – Soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do not stop. The key to driving in soft sand using the appropriate tire pressure, accelerating slowly, avoiding abrupt maneuvers and maintaining the vehicle’s momentum.
STARTING AND OPERATING 471 throttle lightly while holding a light brake pressure and Crossing Large Rocks ease the vehicle up and over the object. When approaching large rocks, choose a path which ensures you drive over the largest with your tires. This WARNING! will lift your undercarriage over the obstacle. The tread of Crossing obstacles can cause abrupt steering system the tire is tougher and thicker than the side wall and is loading which could cause you to loose control of designed to take the abuse.
472 STARTING AND OPERATING vehicle’s mobility. Approach these obstacles at a 45degree angle and let each tire go through the obstacle independently. You need to use caution when crossing large obstacles with steep sides. Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.
STARTING AND OPERATING 473 what is the best direction to recover the vehicle. Depending on what you are in contact with, jack the vehicle up and place a few rocks under the tires so the weight is off of the high point when you let the vehicle down. You can also try rocking the vehicle or winching the vehicle off the object. feel confident with the vehicle and your abilities. You should always climb hills straight up and down. Never attempt to climb a hill on an angle.
474 STARTING AND OPERATING apply more power as you start up the hill. Do not race WARNING! forward into a steep grade, the abrupt change of grade could cause you to lose control. If the front end begins Never attempt to climb a hill at an angle or turn to bounce, ease off the throttle slightly to bring all four around on a steep grade. Driving across an incline tires back on the ground.
STARTING AND OPERATING 475 descent and apply your brakes if necessary, but do not allow the tires to lock. WARNING! WARNING! Driving across an incline increases the risk of a rollover , which may result in severe injury. Do not descend a steep grade in NEUTRAL. Use vehicle brakes in conjunction with engine braking. Descending a grade too fast could cause you to lose control and be seriously injured or killed.
476 STARTING AND OPERATING WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in REVERSE. Never back down a hill in NEUTRAL using only the vehicle brakes. Never drive diagonally across a hill, always drive straight up or down.
STARTING AND OPERATING 477 CAUTION! (Continued) permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy. • Crossing Puddles, Pools, Flooded Areas Or Other Standing Water – Puddles, pools, flooded or other standing water areas normally contain murky or muddy waters. These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom condition.
478 STARTING AND OPERATING stream or river even in shallow water. Fast moving water can easily push your vehicle downstream sweeping it out of control. Even in very shallow water, a high current can still wash the dirt out from around your tires putting you and your vehicle in jeopardy. There is still a high risk of personal injury and vehicle damage with slower water currents in depths greater than the vehicle’s running ground clearance.
STARTING AND OPERATING 479 replace it so, start high and lower it as required. Remember you must return the tires to normal air pressure before driving on road or at highway conditions. Be sure you have a way to return the tires to their normal on road air pressure. CAUTION! Reduced tire pressure increases the risk of tire damage and may cause tire unseating with total loss of air pressure.
480 STARTING AND OPERATING severely hung up on something you should jack the vehicle up and stack something under the wheels to allow the vehicle to roll off the object without causing further damage. This should be tried before attempting any recovery method. CAUTION! Pulling the vehicle off an obstacle, without first clearing the object, may result in additional underbody damage. this process to clean the debris from the tread and improve the traction.
STARTING AND OPERATING 481 designed to take the abusive force generated during vehicle recovery. Do not use the bumper or any other vehicle component as an attachment point. Using tow straps requires coordination between the two drivers. Good communication and line of sight are required for a safe recovery. First connect the tow strap to the correct attachment points on both vehicles. There should be a least 20 to 30 feet between the vehicles to allow for a safe recovery.
482 STARTING AND OPERATING • Winching (Refer To “Winch Operation” For Additional Information) – Winching is most commonly used in the following situations: there is no support vehicle available, a high controlled force is required to recover the vehicle, there is a high risk of environmental or vehicle damage, or where nothing else seems to work. A winch can deliver a high pulling force with a great deal of control. It allows you to walk the vehicle out of the situation in a slow controlled manner.
STARTING AND OPERATING 483 WARNING! Winch cables are under high tension when in use and can become a projectile if they fail. Never stand over or straddle the winch cable. Never jerk or overload the winch cable. Never stand in front of the vehicle while winching. Failure to follow these instructions can result in serious or fatal injury. After Driving Off-Road • Inspect the radiator for mud and debris and clean as required.
484 STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.
STARTING AND OPERATING 485 WARNING! (Continued) WARNING! ground since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.).
486 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. DRIVING THROUGH WATER WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 487 WARNING! CAUTION! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
488 STARTING AND OPERATING CAUTION! (Continued) • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING 489 always a good idea to check for damage. That way you • After extended operation in mud, sand, water, or can get any problems taken care of right away and have similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected your vehicle ready when you need it. and cleaned as soon as possible. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and WARNING! exhaust system for damage.
490 STARTING AND OPERATING WINCH USAGE — POWER WAGON ONLY — (IF EQUIPPED) Things To Know Before Using Your Winch General Winch Information 2. Attach the hook to a suitable anchor point. CAUTION! Be certain the anchor will withstand the load required to tension the wire rope. Your vehicle is equipped with an electric vehicle recovery winch. This winch uses the electrical power from the 3.
STARTING AND OPERATING 491 Low Voltage Interrupt Winch Motor Thermal Protection Your winch is equipped with a device that will interrupt winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out for 30 seconds if this device is tripped. If the interrupt is tripped, the vehicle should be operated at high idle for a few minutes to allow the vehicle charging system to recover before continuing to winch.
492 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components
STARTING AND OPERATING 493 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection to be disconnected from the winch motor to allow the wire rope to be pulled from the winch by hand. switch that automatically stops motor function in the power-in direction if the motor gets too hot. 7. Remote Control: The remote control provides the 2.
494 STARTING AND OPERATING Winch Accessories The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protective gloves while operating the winch or handling the wire rope. Avoid loose fitting clothes or anything that could become entangled in the wire rope and other moving parts.
STARTING AND OPERATING 495 Tree Trunk Protector: Typically made of tough, highquality nylon, it provides the operator an attachment point for the winch rope to a wide variety of anchor points and objects, as well as protect living trees. Operating Your Winch WARNING! Failure to observe any of these warnings regarding proper winch usage may result in severe injury. • Always use supplied hook strap to hold the hook when spooling wire rope in or out. WARNING! (Continued) • Never use as a hoist.
496 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Never wrap wire rope back onto itself. Always use a choker chain, wire choker rope or tree trunk protector on the anchor. • Never attach a recovery strap to the winch hook to increase the length of a pull. • Never attempt to tow a vehicle with the recovery strap attached directly to the winch hook. • Never use ⴖbungeeⴖ straps that develop tremendous and potentially dangerous amounts of force when stretched.
STARTING AND OPERATING 497 4. Always wear leather gloves and do not allow the wire rope to slip through your hands when handling the rope. 5. Only the operator should handle the wire rope and remote control. 6. Think safety at all times. Vehicle Recovery Using The Winch CAUTION! • Always Know Your Winch: Take the time to fully read and understand the included Installation and Operations Guide, and Basic Guide to Winching Techniques, in order to understand your winch and the winching operation.
498 STARTING AND OPERATING 1. Inspect the winch, winch mount, and wire rope for 3. Disengage the clutch to allow free spooling of the damage. Do not use the winch if the mount is loose or winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserves battery power. rope shows excessive wear or damage. Winch Rope 2. Put on gloves. Free Spool 4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point.
STARTING AND OPERATING 499 5 Hook Strap 5. Pull the wire to the anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it can become twisted and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work.
500 STARTING AND OPERATING 6. Secure to the anchor point. Once you have established your anchor point, secure the tree-trunk protector or choker-chain around the object. Tree Trunk Protector CAUTION! Always be certain the anchor you select will withstand the load. NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks. Hook the cable as low as possible.
STARTING AND OPERATING 501 7. Attach the Clevis/D-shackle and Tree Trunk Protector. 8. Lock the clutch. Lock the winch drum by rotating the Attach the shackle to the two ends of the strap or chain clutch lever on the winch to engage. and through the hook loop, being careful not to over NOTE: Always ensure the clutch is fully engaged or tighten (tighten and back-off 1/2 turn). disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper.
502 STARTING AND OPERATING 11. Check your anchor. Make sure all connections are Winch Box Remote Control secured and free of debris before continuing with the 10. Put wire rope under tension. Using the remote conwinching procedure. trol switch, slowly wind the wire rope until no slack remains. Once the wire rope is under tension, stand 12. Check wire rope. The wire rope should be neatly well clear of it and never step over it. wound around the spooling drum.
STARTING AND OPERATING 503 Wire Neatly Wound Around The Spooling Drum In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approach or move the blanket once tension is applied. Do not allow it to get pulled into the fairlead.
504 STARTING AND OPERATING behind or in front of the vehicle and never near the wire rope or snatch block. Your situation may have other ⴖno peopleⴖ zones. rope is winding evenly and tightly around the spooling drum. For additional assistance, the winched vehicle can be slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are able to drive the vehicle, the winching operation is complete. No People Zones 14. Begin winching.
STARTING AND OPERATING 505 NOTE: an uneven stack, spool out that section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. • Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down. 15. Secure vehicle. Once recovery of the vehicle is complete, be sure to secure the vehicle’s brakes and shift • What to look for under load: The wire rope must the transmission to PARK.
506 STARTING AND OPERATING WARNING! To prevent serious injury, NEVER put your fingers inside the hook area as you are powering-in. NOTE: How to spool under no load: Arrange the remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary.
STARTING AND OPERATING 507 NOTE: Always store the remote control in a protected, clean, dry area. Rigging Techniques Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or maintaining a straight-line pulling situation. You will have to assess what technique is correct for your situation. Think ⬙safety⬙ at all times. Hook In Stored Position 19.
508 STARTING AND OPERATING How To Change The Pulling Direction block, secured to a point directly in front of the vehicle will enable you to change your pulling direction while still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing Pulling Power In some cases, you may find yourself needing more pulling power. The use of snatch blocks increases mechanical advantage and that increases your pulling power.
STARTING AND OPERATING 509 Double Line wire rope to free the winch hook. Attach the hook to your vehicle’s frame/tow hook and run the wire rope through a snatch block. Disengage the clutch and, using the snatch block, pull out enough wire to reach your anchor point. Do not attach the hook to the mounting kit. Secure to the anchor point with a tree trunk protector or choker chain. Attach the clevis/shackle.
510 STARTING AND OPERATING If the Steering icon is flashing, it indicates that the vehicle NOTE: needs to be taken to the dealer for service. It is likely the • Even if the power steering assistance is no longer vehicle has lost power steering assistance. operational, it is still possible to steer the vehicle.
STARTING AND OPERATING 511 If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. NOTE: CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur.
512 STARTING AND OPERATING CAUTION! FUEL SAVER TECHNOLOGY 5.7L/6.4L ENGINES ONLY — IF EQUIPPED Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty. This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required.
STARTING AND OPERATING 513 NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
514 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
STARTING AND OPERATING 515 BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle. Four-Wheel Anti-Lock Brake System WARNING! The Four-Wheel Anti-Lock Brake System contains sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
516 STARTING AND OPERATING The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. The ABS conducts a low-speed selftest at about 10 mph (16 km/h). If you have your foot lightly on the brake while this test is occurring, you may feel slight pedal movement. The movement can be more apparent on ice and snow. This is normal.
STARTING AND OPERATING 517 WARNING! (Continued) • The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. NOTE: Under cold temperatures, pedal effort will be higher than normal until the power steering fluid reaches operating temperature.
518 STARTING AND OPERATING hydraulic brake pressure to prevent wheel lockup and Traction Control System (TCS) — If Equipped help avoid skidding on slippery surfaces during braking. The TCS monitors the amount of wheel spin of each of the NOTE: ABS improves steering control of the vehicle driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s), and engine power is during hard braking maneuvers. reduced to provide enhanced acceleration and stability.
STARTING AND OPERATING 519 BAS detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. The system applies optimum pressure to the brakes in emergency braking conditions. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance. To receive the benefit of BAS, you must apply continuous braking pressure during the stopping sequence.
520 STARTING AND OPERATING duration once the driver takes his foot off of the brake • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backpedal. If the driver does not apply the throttle during this ing uphill is in REVERSE gear). short duration, the system will release brake pressure and the vehicle will roll down the incline. The system will release brake pressure in proportion to the amount of WARNING! throttle applied.
STARTING AND OPERATING 521 The system will work in REVERSE and all forward gears, and will not activate if the vehicle is placed in NEUTRAL. Towing And Hauling With HSA The HSA system does not know if your vehicle is loaded or towing a trailer unless the TOW/HAUL switch, located on the center stack, is selected. When activated, the “TOW/HAUL Indicator Light” will illuminate in the instrument cluster. Refer to “Automatic Transmission” in “Starting and Operating” for further information.
522 STARTING AND OPERATING WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK or using the parking brake, it will roll down the incline and could collide with another vehicle, object or person, and cause serious or fatal injury. Always remember to use the parking brake while parking on a hill and that the driver is responsible for braking the vehicle. HSA Off Non-EVIC Equipped Vehicles 3.
STARTING AND OPERATING 523 the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or HSA is a Customer Programmable Feature on an EVIC understeer condition. equipped vehicle. If you wish to turn off the HSA feature, refer to “Electronic Vehicle Information Center (EVIC)/ • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position.
524 STARTING AND OPERATING WARNING! (Continued) from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. 4WD LOCK or 4WD AUTO, the ESC system will be in this mode. This mode should be used for almost all driving situations.
STARTING AND OPERATING 525 NOTE: To improve the vehicle’s traction when driving with snow chains or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch. Once the situation requiring ESC to be switched to the “Partial Off” mode is overcome, turn ESC back on by momentarily pressing the “ESC Off” switch. This may be done while the vehicle is in motion.
526 STARTING AND OPERATING All Four-Wheel Drive Vehicles In 4WD AUTO And 4WD LOCK Modes Can Also Choose The Following ESC Operating Mode. This Is The Only Selectable ESC Operating Mode in 4WD LOW: Full Off This mode is intended for off-road use when ESC stability features could inhibit vehicle maneuverability due to trail conditions. This mode is entered by pressing and holding the “ESC Off” switch for five seconds when the vehicle is stopped and the engine is running.
STARTING AND OPERATING 527 “ESC Off” is the only operating mode for ESC in 4WD ESC Activation/Malfunction Indicator Light And LOW. Whenever the vehicle is started in 4WD LOW or ESC OFF Indicator Light the transfer case (if equipped) is shifted from 4WD LOCK or NEUTRAL, to 4WD LOW, the ESC system will be in The “ESC Activation/Malfunction Indicator this mode. Light” in the instrument cluster will come on when the ignition switch is turned to the ON WARNING! position.
528 STARTING AND OPERATING when ESC becomes inactive following the maneuver that The “ESC Activation/Malfunction Indicator Light” (locaused the ESC activation. cated in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also The “ESC OFF Indicator Light” indicates the flashes when TCS is active.
STARTING AND OPERATING 529 further information. When TSC is functioning, the “ESC TIRE SAFETY INFORMATION Activation/Malfunction Indicator Light” will flash, the Tire Markings engine power may be reduced and you may feel the brakes being applied to individual wheels to attempt to stop the trailer from swaying. TSC is disabled when the ESC system is in the “Partial Off” or “Full Off” modes. TSC is only active in the default “ESC On” mode.
530 STARTING AND OPERATING • Temporary spare tires are designed for temporary emergency use only. Temporary high pressure com• P (Passenger) - Metric tire sizing is based on U.S. pact spare tires have the letter “T” or “S” molded into design standards. P-Metric tires have the letter “P” the sidewall preceding the size designation. Example: molded into the sidewall preceding the size designaT145/80D18 103M. tion. Example: P215/65R15 95H. • High flotation tire sizing is based on U.S.
STARTING AND OPERATING 531 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
532 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 533 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
534 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 535 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
536 STARTING AND OPERATING Tire And Loading Information Placard 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING 537 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here.
538 STARTING AND OPERATING • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs • If your vehicle will be towing a trailer, load from your (392 kg). trailer will be transferred to your vehicle. The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
STARTING AND OPERATING 539 5
540 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 541 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. NOTE: • Unequal tire pressures from side to side may cause erratic and unpredictable steering response.
542 STARTING AND OPERATING judgement when determining proper inflation. Tires Check tire pressures more often if subject to a wide range may look properly inflated even when they are under- of outdoor temperatures, as tire pressures vary with inflated. temperature changes. • Inspect tires for signs of tire wear or visible damage. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap.
STARTING AND OPERATING 543 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
544 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
STARTING AND OPERATING 545 If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode.
546 STARTING AND OPERATING rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT” in “What To Do Compact Spare Tire — If Equipped In Emergencies” for further information.
STARTING AND OPERATING 547 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life.
548 STARTING AND OPERATING WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 549 tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven • Performance tires, tires with a speed rating of V or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle maintenance schedule is highly recommended.
550 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 551 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
552 STARTING AND OPERATING • Traction device must be of proper size for the tire, as recommended by the traction device manufacturer. Use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard Please follow the table below for proper tire size, chain against damage.
STARTING AND OPERATING 553 WARNING! CAUTION! (Continued) Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used.
554 STARTING AND OPERATING The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern Tires on the front and rear axles of vehicles operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed. and braking functions. For these reasons, they wear at unequal rates. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 555 Directional Tires — If Equipped Dual Rear Wheels — If Equipped For the R/T package with 22” tires and wheels, the rotational direction of the tire must be taken into consideration when rotating the tires. The recommended rotation pattern for directional tires is shown below. The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires.
556 STARTING AND OPERATING NOTE: If your vehicle is equipped with a Tire Pressure • If the tires are rotated incorrectly, The Auto localization Information System (TPIS): of the TPIS sensors will fail to locate correctly resulting in incorrect locations for the pressure values displayed • The Tire Pressure Information System (TPIS) uses in the Instrument Cluster.
STARTING AND OPERATING 557 CAUTION! (Continued) • When replacing a flat, the spare tire may have to be remounted on the rim, or installed at a different location, to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the truck. For example, if the spare is used to replace an outer rear tire it will have to be remounted on the rim so that the wheel is dished inward.
558 STARTING AND OPERATING The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warning (Tire Pressure Monitoring [TPM] Telltale Light) illuminates, you must increase the tire pressure to the recommended cold placard pressure in order for the “Tire Pressure Monitoring Telltale Light” to turn off.
STARTING AND OPERATING 559 CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable.
560 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, The matching full size spare wheel and tire assembly (if and the TPMS will monitor the actual tire pressure in equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The the tire. TPMS will only monitor the pressure in the full size spare Base System when it is used in place of a road tire.
STARTING AND OPERATING 561 to the vehicle’s recommended cold placard pressure 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as value as shown in the ⬙Inflate to XX⬙ message. Once the the TPM sensors. system receives the updated tire pressures, the system will automatically update and the “Tire Pressure Moni2.
562 STARTING AND OPERATING displayed, and the “Tire Pressure Monitoring Telltale The TPMS consists of the following components: Light” will turn ON. An ⬙Inflate to XX⬙ message will • Receiver module, also be displayed. • Four TPM sensors, 3.
STARTING AND OPERATING 563 Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display a “LOW TIRE PRESSURE” message for a minimum of five seconds and a graphic showing the pressure values of each tire with the low tire pressure values flashing or in a different color.
564 STARTING AND OPERATING will automatically update, the graphic display in the EVIC will stop flashing or return to it’s original color, and the “Tire Pressure Monitoring Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. Service TPMS Warning If a system fault is detected, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid.
STARTING AND OPERATING 565 SYSTEM⬙ message will no longer display, and a pressure 2. If you install the full size spare in place of a road tire value will display in place of the dashes. A system fault that has a pressure below the low-pressure warning can occur due to any of the following: limit, upon the next ignition switch cycle, a chime will sound and the “Tire Pressure Monitoring Telltale 1. Signal interference due to electronic devices or driving Light” will turn ON.
566 STARTING AND OPERATING Tire Pressure Information System (TPIS) 3500 Series Trucks • Six TPM sensors (Dual Rear Wheel (DRW) applications) Your vehicle may be equipped with a Tire Pressure • Pressure display in the Electronic Vehicle Information Information System (TPIS). Center (EVIC) The Tire Pressure Information System (TPIS) uses wireless technology with wheel rim mounted electronic sensors to transmit tire pressure levels.
STARTING AND OPERATING 567 If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the ⬙SERVICE TPM SYSTEM⬙ message will no longer be displayed, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada.
568 STARTING AND OPERATING an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. 3.6L/6.4L Engine The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in These engines are designed to meet all these engines. emissions regulations and provide excelLight spark knock at low engine speeds is not harmful to lent fuel economy and performance when your engine.
STARTING AND OPERATING 569 Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
570 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles • Change the engine oil and oil filter. Non-Flex Fuel Vehicles (FFV) are compatible with gaso- • Disconnect and reconnect the battery to reset the line containing 10% ethanol (E10). Gasoline with higher engine controller memory. ethanol content may void the New Vehicle Limited More extensive repairs will be required for prolonged Warranty. exposure to E-85 fuel.
STARTING AND OPERATING 571 therefore, you should ask your gasoline retailer whether Fuel System Cautions the gasoline contains MMT. MMT is prohibited in Federal and California reformulated gasoline. CAUTION! Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost.
572 STARTING AND OPERATING CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you.
STARTING AND OPERATING 573 WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL (3.6L ENGINE ONLY) — IF EQUIPPED 5 E-85 General Information The information in this section is for Flexible Fuel vehicles only.
574 STARTING AND OPERATING WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame. Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of E-85 Badge these two.
STARTING AND OPERATING 575 • you operate the vehicle immediately after refueling for Selection Of Engine Oil For Flexible Fuel Vehicles a period of at least 5 minutes (E-85) And Gasoline Vehicles Observing these precautions will avoid possible hard FFV vehicles operated on E-85 require specially formustarting and/or significant deterioration in driveability lated engine oils. These special requirements are included in MOPAR® engine oils, and in equivalent oils meeting during warm up.
576 STARTING AND OPERATING increase in the time it takes for your engine to start, and that your vehicle is serviced with correct ethanol coma deterioration in driveability (sags and/or hesitations) patible parts. until the engine is fully warmed up. NOTE: Use of the engine block heater (if equipped) is beneficial for E-85 startability when the ambient temperature is less than 32°F (0°C).
STARTING AND OPERATING 577 NOTE: When removing the fuel filler cap, lay the cap The fuel filler cap (gas cap) is located behind the fuel tether in the hook, located on the fuel filler door. filler door, on the left side of the vehicle. Open the fuel CAUTION! door and remove the fuel cap by turning it counterclockwise. • Damage to the fuel system or emissions control ADDING FUEL system could result from using an improper fuel tank filler tube cap (gas cap).
578 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound.
STARTING AND OPERATING 579 Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the EVIC telltale display area. Refer to “Electronic Vehicle Information Center (EVIC) in “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the SELECT button to turn off the message.
580 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Inflation Pressure The GAWR is the maximum permissible load on the front This is the cold tire inflation pressure for your vehicle for and rear axles. The load must be distributed in the cargo all loading conditions up to full GAWR. area so that the GAWR of each axle is not exceeded.
STARTING AND OPERATING 581 The weight on the front and rear of the vehicle should CAUTION! then be determined separately to be sure that the load is properly distributed over the front and rear axle. Weigh- Do not load your vehicle any heavier than the GVWR ing the vehicle may show that the GAWR of either the or the maximum front and rear GAWR. If you do, front or rear axles has been exceeded but the total load is parts on your vehicle can break, or it can change the within the specified GVWR.
582 STARTING AND OPERATING measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be The following trailer towing related definitions will assist supported by the scale. you in understanding the following information: Gross Combination Weight Rating (GCWR) Gross Vehicle Weight Rating (GVWR) Common Towing Definitions The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
STARTING AND OPERATING 583 WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
584 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
STARTING AND OPERATING 585 Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Type and Maximum Trailer Weight The following chart provides the maximum trailer weight a given factory equipped trailer hitch type can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
586 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The rear bumper is intended to tow trailers up to a 5,000 lbs (2 268 kg) without added equipment or alterations to the standard equipment. Ram 1500 4x2 3.6L V-6 8–Speed Automatic Transmission 5.
STARTING AND OPERATING 587 Ram 1500 4x4 3.6L V-6 8–Speed Automatic Transmission 5.
588 STARTING AND OPERATING Ram 2500 And 3500 5.7L HEMI® V-8 6–Speed Automatic Transmission 6.4L HEMI® V-8 6–Speed Automatic Transmission ST Max Towing: 13,850 lbs (6 282 kg) Max Payload: 4,480 lbs (2 032 kg) Max Towing: 16,450 lbs (7 462 kg) Max Payload: 7,220 lbs (3 275 kg) NOTE: For additional trailer towing information (maximum trailer weight ratings) refer to the following website addresses: • http://www.ramtrucks.com • http://www.ramtruck.
STARTING AND OPERATING 589 Trailer And Tongue Weight Always load a trailer with 60% of the weight in the front of the trailer. This places 10% of the GTW on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your trailer hitch.
590 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for further information.
STARTING AND OPERATING 591 WARNING! WARNING! (Continued) Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision.
592 STARTING AND OPERATING WARNING! (Continued) 3. GAWR 4. Tongue weight rating for the trailer hitch utilized. Towing Requirements — Tires • When replacing tires, refer to “Tires – General Information” in “Starting and Operating” for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. • Do not attempt to tow a trailer while using a compact Towing Requirements — Trailer Brakes spare tire.
STARTING AND OPERATING 593 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 1,653 lbs (750 kg).
594 STARTING AND OPERATING The user interface consists of the following: Manual Brake Control Lever Slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes.
STARTING AND OPERATING 595 sliding the manual brake control lever will display the Adjusting GAIN GAIN setting for 10 seconds and the “Trailer Brake Status NOTE: This should only be performed in a traffic free Indicator Light” will not be displayed. environment at speeds of approximately 20–25 mph If a fault is detected in the trailer wiring or the Integrated (30–40 km/h). Trailer Brake Module (ITBM), the “Trailer Brake Status 1. Make sure the trailer brakes are in good working Indicator Light” will flash.
596 STARTING AND OPERATING 4. Press the UP or DOWN button on the steering wheel 8. In a traffic-free environment, tow the trailer on a dry, until “TRAILER TOW” appears on the screen. level surface at a speed of 20–25 mph (30–40 km/h) and squeeze the manual brake control lever com5. Press the RIGHT arrow on the steering wheel to enter pletely. “TRAILER TOW”. 9. If the trailer wheels lockup (indicated by squealing 6.
STARTING AND OPERATING 597 Type of Trailer Brakes Light Electric Electric Trailer Brakes Heavy Electric Electric Trailer Brakes Load *Under 10,000 lbs *Above 10,000 lbs Light EOH Electric over Hydraulic Trailer Brakes *Under 10,000 lbs Heavy EOH Electric over Hydraulic Trailer Brakes *Above 10,000 lbs * The suggested selection depends and may change Vehicle Information Center” in “Understanding Your depending on the customer preferences for braking per- Instrument Panel” for further information.
598 STARTING AND OPERATING WARNING! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in personal injury. NOTE: • An aftermarket controller may be available for use with trailers with air or electric-over-hydraulic trailer brake systems.
STARTING AND OPERATING 599 5 Four-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn Seven-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
600 STARTING AND OPERATING When towing a loaded trailer up steep grades at low speeds (20 mph [32 km/h] or below), holding your Before setting out on a trip, practice turning, stopping vehicle in first gear (using the ERS switches) can help to and backing the trailer up in an area away from heavy avoid transmission overheating. traffic.
STARTING AND OPERATING 601 Electronic Speed Control — If Equipped Air Conditioning • Do not use in hilly terrain or with heavy loads. Turn off temporarily. • When using the speed control, if you experience speed Air Suspension System drops greater than 10 mph (16 km/h), disengage until To aid in attaching/detaching the trailer from the vehicle, you can get back to cruising speed. the air suspension system can be used.
602 STARTING AND OPERATING WARNING! WARNING! (Continued) Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deploy unexpectedly or could fail to deploy during a collision resulting in serious injury or death. Do not expect that the airbag will perform as described earlier in this manual.
STARTING AND OPERATING 603 WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in a collision. Do not expect that the airbag will perform as described earlier in this manual. CAUTION! The “Lamp Out” indicator could illuminate if exterior lamps are not properly installed. Before Plowing • Check the runners and cutting edge for excessive wear. The cutting edge should be ¼ to ½ in (6 cm to 1.2 cm) above ground in snow plowing position.
604 STARTING AND OPERATING The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver, passengers, options, and cargo, must not exceed either the Gross Vehicle Weight (GVWR) or Gross Axle Weight (GAWR) ratings. These weights are specified on the Safety Compliance Certification Label on the driver’s side door opening. NOTE: Detach the snowplow when transporting passengers.
STARTING AND OPERATING 605 • Vehicles with automatic transmissions should use 4L range when plowing deep or heavy snow for extended Snowplows should be maintained in accordance with the periods of time to avoid transmission overheating. plow manufacturer’s instructions. General Maintenance • Do not shift the transmission unless the engine has returned to idle and wheels have stopped.
606 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 607 NOTE: Vehicles equipped with air suspension must be lowered to the “Entry/Exit” (lowest) level, and have automatic leveling disabled, before tying them down (from the body) on a trailer or flatbed truck. Refer to “Air Suspension – If Equipped” for more information. If the vehicle cannot be lowered to the “Entry/Exit” level (for example, engine will not run), tie-downs must be fastened to the axles (not to the body).
608 STARTING AND OPERATING CAUTION! CAUTION! • Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • Do not disconnect the driveshaft because fluid may leak from the transmission, causing damage to internal parts. • Front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
STARTING AND OPERATING 609 CAUTION! (Continued) • Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • Do not disconnect the rear drive shaft because fluid will leak from the transfer case, causing damage to internal parts. • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged.
610 STARTING AND OPERATING 1. Bring the vehicle to a complete stop, with the engine running. Firmly apply the parking brake. 2. Shift the transmission to NEUTRAL. 3. Press and hold the brake pedal. 4. Depress the clutch pedal on a manual transmission. transfer case control knob. The NEUTRAL (N) indicator light will blink while the shift is in progress. The light will stop blinking (stay on solid) when the shift to NEUTRAL (N) is complete.
STARTING AND OPERATING 611 11. Shift the transmission into PARK or place manual transmission in gear (NOT in Neutral). On 8-speed transmissions the shifter will automatically select PARK when the engine is turned off. met during the shift, the NEUTRAL (N) indicator light will flash continuously until all requirements are met or until the NEUTRAL (N) button is released. 12.
612 STARTING AND OPERATING 3. Press and hold the brake pedal. 4. Start the engine. Shift the transmission into NEUTRAL. Depress the clutch pedal on a manual transmission. • With manual shift transfer case, shift the transfer case lever to the desired position. • With electronic shift transfer case with rotary selector switch, press and hold the transfer case NEUTRAL (N) button until the NEUTRAL (N) indicator light turns off. After the NEUTRAL (N) indicator light turns off, release the NEUTRAL (N) button.
STARTING AND OPERATING 613 • The ignition switch must be in the ON/RUN position for a shift to take place and for the position indicator 10. Release the parking brake. lights to be operable. If the ignition switch is not in the ON/RUN position, the shift will not take place and no 11. Shift the transmission into gear, release the brake position indicator lights will be on or flashing. pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .617 䡵 JUMP-STARTING PROCEDURES . . . . . . . . . . .659 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .617 ▫ Preparations For Jump-Start . . . . . . . . . . . . . .660 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .618 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . .661 ▫ Torque Specifications . . . . . . . . . . . . . . . . . .619 䡵 JACKING AND TIRE CHANGING . . . . . . . . .
616 WHAT TO DO IN EMERGENCIES 䡵 MANUAL PARK RELEASE — 8 SPEED TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . .668 䡵 TOWING A DISABLED VEHICLE . . . . . . . . . . .670 ▫ Two-Wheel Drive Models . . . . . . . . . . . . . . . .672 ▫ Four-Wheel Drive Models. . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 617 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the upper switch bank just below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all direc- • On the highways — slow down.
618 WHAT TO DO IN EMERGENCIES supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately and call for service.
WHAT TO DO IN EMERGENCIES 619 Torque Specifications Lug Nut/Bolt Torque Lug Nut/ Bolt Type **Lug Nut/Bolt Size 130 Ft-Lbs (176 N·m) 140 Ft-Lbs (190 N·m) Cone M14 x 1.50 Lug Nut/ Bolt Socket Size 22 mm Flanged **Use only Chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Do not oil wheel studs. NOTE: Dual wheels are flat mounted, center piloted. Inspect the wheel mounting surface prior to mounting The lug nuts are a two-piece assembly.
620 WHAT TO DO IN EMERGENCIES Wheel Mounting Surface 4 And 5 Lug Nuts/Bolts Torque Pattern Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. WARNING! After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered.
WHAT TO DO IN EMERGENCIES 621 JACKING AND TIRE CHANGING WARNING! (Continued) Jacking And Tire Changing 1500 Series Trucks WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
622 WHAT TO DO IN EMERGENCIES Removal Of Jack And Tools (1500 Series) To access the jack and jack tools you must remove the plastic access cover, located on the side of the front passengers seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab. Once the front of the cover is loose, slide the cover toward the front of the seat until it is free from the seat frame.
WHAT TO DO IN EMERGENCIES 623 6 Jack And Tools (1500 Series) Release the tool bag straps from the jack and remove tools from bag.
624 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Removing The Spare Tire 1. Remove the spare tire before attempting to jack up the truck.
WHAT TO DO IN EMERGENCIES 625 6 Inserting The Jack Extension Tube Into The Access Hole 2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
626 WHAT TO DO IN EMERGENCIES 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. Gaining Access To The Retainer 5. Pull the retainer through the center of the wheel. Pulling The Spare Tire Out 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable.
WHAT TO DO IN EMERGENCIES 627 Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. Pulling The Retainer Through The Center Of The Wheel 3. Set the parking brake.
628 WHAT TO DO IN EMERGENCIES 5. Turn the ignition OFF. WARNING! (Continued) Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher.
WHAT TO DO IN EMERGENCIES 629 WARNING! (Continued) • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1.
630 WHAT TO DO IN EMERGENCIES 4X2 Front Jacking Location Indicator 4X2 Front Jacking Location When changing a front wheel, place the scissor jack 4x4 Series Trucks Front Jacking Location under the rear portion of the lower control arm as shown There is a jack location indicator on the rear portion of the below. lower control arm.
WHAT TO DO IN EMERGENCIES 631 6 4X4 Front Jacking Location Indicator 4X4 Front Jacking Location When changing a front wheel, place the scissor jack 4x2 and 4x4 Rear Jacking Location under the rear portion of the lower control arm as shown Operate the jack using the jack drive tube and the wheel below. wrench. The tube extension may be used but is not required.
632 WHAT TO DO IN EMERGENCIES For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the CAUTION! axle between the wheel and the shock bracket with the Before raising the wheel off the ground, make sure drive tubes extending to the rear. that the jack will not damage surrounding truck parts and adjust the jack position as required. 4.
WHAT TO DO IN EMERGENCIES 633 end of the wheel nuts toward the wheel. To avoid the 7. Install the wheel center cap and remove the wheel risk of forcing the vehicle off the jack, do not fully blocks. Do not install chrome or aluminum wheel tighten the wheel nuts until the vehicle has been center caps on the spare wheel. This may result in cap lowered. damage. 6. Finish tightening the lug nuts. Push down on the 8. Lower the jack to its fully closed position.
634 WHAT TO DO IN EMERGENCIES To Stow The Flat Or Spare NOTE: Vehicles equipped with aluminum wheels cannot be stored under the vehicle because the wheel retainer will not fit through the wheel pilot hole. Secure the flat tire in the bed of the truck. Have the flat tire repaired or replaced immediately. WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately. Reinstalling The Retainer 2.
WHAT TO DO IN EMERGENCIES 635 6 Pulling The Retainer Through The Center Of The Wheel And Positioning It 3. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
636 WHAT TO DO IN EMERGENCIES 4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in place. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES 637 Jack And Tool Bag 3. Secure the tool bag straps to the jack. Jack And Tools Tied 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor.
638 WHAT TO DO IN EMERGENCIES Jack Hold Down Fastener Jack And Tools (1500 Series) NOTE: Ensure that the jack slides into the front hold down location. WARNING! 5. Turn the wing bolt clockwise to secure to the floor pan. Reinstall the plastic cover. After using the jack and tools, always reinstall them in the original carrier and location.
WHAT TO DO IN EMERGENCIES 639 WARNING! (Continued) WARNING! (Continued) you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
640 WHAT TO DO IN EMERGENCIES Jack Location The jack and jack tools are stored under the front passenger seat. Removal Of Jack And Tools (2500, 3500 Series) To access the jack and jack tools you must remove the plastic access cover, located on the side of the front passengers seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab.
WHAT TO DO IN EMERGENCIES 641 6 Jack And Tools (2500/3500 Series) Remove the jack and tools from the bracket assembly. Turn the jack-turn-screw counterclockwise to release jack from bracket assembly.
642 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Removing The Spare Tire 1. Remove the spare tire before attempting to jack up the truck.
WHAT TO DO IN EMERGENCIES 643 6 Inserting The Jack Extension Tube Into The Access Hole Rotating The Wheel Wrench Handle 2. Rotate the wheel wrench handle counterclockwise 3. Pull the spare tire out from under the vehicle to gain until the spare tire is on the ground with enough cable access to the spare tire retainer. slack to allow you to pull it out from under the vehicle.
644 WHAT TO DO IN EMERGENCIES Pulling The Spare Tire Out Gaining Access To The Retainer 4. Lift the spare tire with one hand to give clearance to 5. Pull the retainer through the center of the wheel. tilt the retainer at the end of the cable.
WHAT TO DO IN EMERGENCIES 645 Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. Pulling The Retainer Through The Center Of The Wheel 3. Set the parking brake.
646 WHAT TO DO IN EMERGENCIES 5. Turn the ignition OFF. WARNING! (Continued) Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher.
WHAT TO DO IN EMERGENCIES 647 WARNING! (Continued) • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.
648 WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. NOTE: If your vehicle is equipped with hub caps/wheel covers they must be removed before raising the vehicle off the ground. Refer to ”Hub Caps/Wheel Covers — If Equipped” in this section. 2. Using the lug wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. Changing a dually tire requires the lug wrench adapter.
WHAT TO DO IN EMERGENCIES 649 Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required. 6 Lug Wrench Adapter And Wrench 3. Placement of the jack: 4x2 Series Trucks Front Jacking Location 4x2 Front Jacking Location For 2500 and 3500 4x2 series trucks, when changing a 4x4 Series Trucks Front Jacking Location front wheel, place the bottle jack under the frame rail behind the wheel.
650 WHAT TO DO IN EMERGENCIES connect the drive tube to the extension tube. Place the 4x2 and 4x4 Rear Jacking Location jack under the axle as close to the tire as possible with the For 4x2 and 4x4 trucks, when changing a rear wheel, drive tubes extending to the front. Connect the jack tube assemble the jack drive tube to the jack and connect the extension and wheel wrench. drive tube to the extension tube.
WHAT TO DO IN EMERGENCIES 651 Connect the jack tube extension and wheel wrench. CAUTION! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause a collision. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off.
652 WHAT TO DO IN EMERGENCIES Inner Wheel Proper Placement Dual Rear Wheel Placement 6. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. For the correct lug nut torque refer to “Torque Specifications” in this section.
WHAT TO DO IN EMERGENCIES 653 them checked with a torque wrench by you authorized 9. Adjust the tire pressure when possible. dealer or service station. NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. 7. Install the wheel center cap and remove the wheel blocks.
654 WHAT TO DO IN EMERGENCIES Reinstalling The Retainer Pulling The Retainer Through The Center Of The Wheel And Positioning It 2. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable and position it 3. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. properly across the wheel opening.
WHAT TO DO IN EMERGENCIES 655 mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in place. 6 Wheel Wrench And Jack Extension Tube Assembled And In Position 4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle.
656 WHAT TO DO IN EMERGENCIES NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Reinstalling The Jack And Tools (2500 And 3500 Series) 1. Tighten the jack all the way down by turning the jack turn-screw counterclockwise until the jack is snug. 2. Position the jack and tools into bracket assembly. Make sure the lug wrench is under the jack near the jack turn-screw.
WHAT TO DO IN EMERGENCIES 657 6 Jack Hold Down Fastener Jack And Tools (2500/3500 Series) NOTE: Ensure that the jack and tool bracket assembly Hub Caps/Wheel Covers — If Equipped slides into the front hold down location. The hub caps must be removed before raising the vehicle 4. Turn the wing bolt clockwise to secure to the floor pan. off the ground. Reinstall the plastic cover.
658 WHAT TO DO IN EMERGENCIES CAUTION! Use extreme caution when removing the front and rear center caps. Damage can occur to the center cap and/or the wheel if screwdriver type tools are used. A pulling motion, not a pry off motion, is recommended to remove the caps. For single rear wheel (SRW) models, use the flat blade on the end of the lug wrench to pull the hub cap off. Insert the blade end into the pull off notch and carefully pull the hub cap off with a back and forth motion.
WHAT TO DO IN EMERGENCIES 659 Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lug nut bolt circle and strike the high side down with a rubber mallet. Be sure that the hub caps and wheel skins are firmly seated around the wheel. HOISTING JUMP-STARTING PROCEDURES If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
660 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post.
WHAT TO DO IN EMERGENCIES 661 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
662 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. Connecting The Jumper Cables 1.
WHAT TO DO IN EMERGENCIES 663 Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 3. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery.
664 WHAT TO DO IN EMERGENCIES pressing the accelerator. Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine. the risk of transmission failure during prolonged efforts to free a stuck vehicle. NOTE: For trucks equipped with 8-speed automatic transmission: Shifts between DRIVE and REVERSE can only be achieved at wheel speeds of 5 mph (8 km/h) or less.
WHAT TO DO IN EMERGENCIES 665 CAUTION! (Continued) EMERGENCY TOW HOOKS — IF EQUIPPED • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring). Your vehicle may be equipped with emergency tow hooks. WARNING! WARNING! Fast spinning tires can be dangerous.
666 WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. 5. Insert a screwdriver or similar tool, into the access port (ringed circle) on the bottom of the steering column and push and hold the override release lever up.
WHAT TO DO IN EMERGENCIES 667 Center Console Shifter — If Equipped 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the shift lever override access cover (located to the right of the shift lever). 4. Press and maintain firm pressure on the brake pedal. 5. Insert the screwdriver or similar tool into the access hole, and push and hold the override release lever down. 6 Shift Lever Override Access Cover 6.
668 WHAT TO DO IN EMERGENCIES MANUAL PARK RELEASE — 8 SPEED TRANSMISSION WARNING! Always secure your vehicle by fully applying the parking brake, before activating the Manual Park Release. Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake or by proper connection to a tow vehicle. Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.
WHAT TO DO IN EMERGENCIES 669 2. Using a small screwdriver or similar tool, remove the To Reset The Manual Park Release: Manual Park Release access cover, which is just above 1. Push the locking tab to the right, to unlock the lever. the parking brake release handle, below and to the left 2. Rotate the Manual Park Release lever forward to its of the steering column. original position, until the locking tab snaps into place 3. Using the screwdriver or similar tool, push the to secure the lever.
670 WHAT TO DO IN EMERGENCIES NOTE: Vehicles equipped with air suspension must be This section describes procedures for towing a disabled placed in Transport mode, before tying them down (from vehicle using a commercial wrecker service. If the trans- the body) on a trailer or flatbed truck. Refer to ⬙Air Suspension⬙ in ⬙Starting and Operating⬙ for more informission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational mation.
WHAT TO DO IN EMERGENCIES 671 Towing Condition Flat Tow Wheel Lift or Dolly Tow Flatbed Wheels OFF the Ground NONE 2WD Models If transmission is operable: • Transmission in NEUTRAL • 30 mph (48 km/h) max speed • 15 miles (24 km) max distance (6–speed transmission) • 30 miles (48 km) max distance (8–speed transmission) 4WD Models Front Rear OK See instructions in “Recreational Towing” under “Starting and Operating” • Automatic Transmission in PARK • Manual Transmission in gear ( NOT NEUTRAL) • Trans
672 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent CAUTION! damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- Do not use sling type equipment when towing. ment manufacturer’s instructions. Use of safety chains is When securing the vehicle to a flat bed truck, do not mandatory. Attach a tow bar or other towing device to attach to front or rear suspension components.
WHAT TO DO IN EMERGENCIES 673 • The towing distance must not exceed 15 miles (24 km) for 6-speed transmission, or 30 miles (48 km) for 8-speed transmission. If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km) for 6-speed transmission, or 30 miles (48 km) for 8-speed transmission, tow with the rear wheels OFF the ground.
674 WHAT TO DO IN EMERGENCIES If flatbed equipment is not available, and the transfer case is operable, the vehicle may be towed (in the forward direction, with ALL wheels on the ground), IF the transfer case is in NEUTRAL (N) and the transmission is in PARK (for automatic transmissions) or in gear (NOT in NEUTRAL, for manual transmissions). Refer to “Recreational Towing” in “Starting And Operating” for further information and detailed instructions. CAUTION! • Front or rear wheel lifts must not be used.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .678 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . .685 䡵 ENGINE COMPARTMENT — 5.7L . . . . . . . . . .679 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .688 䡵 ENGINE COMPARTMENT — 6.4L . . . . . . . . . .680 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .689 䡵 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . .681 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .
676 MAINTAINING YOUR VEHICLE ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . .694 䡵 REPLACEMENT BULBS . . . . . . . . . . . . . . . . .730 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . .697 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . . .732 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .704 ▫ Rear Axle And 4x4 Front Driving Axle Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .706 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 677 ▫ Side Marker Lamps (Dual Rear Wheels) — 䡵 FLUIDS, LUBRICANTS AND GENUINE PARTS . .744 If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .741 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .744 䡵 FLUID CAPACITIES . . . . . . . . . . . . . . . . . . . .742 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .
678 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 679 ENGINE COMPARTMENT — 5.
680 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 6.
MAINTAINING YOUR VEHICLE 681 ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
682 MAINTAINING YOUR VEHICLE “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 683 3. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
684 MAINTAINING YOUR VEHICLE available which include detailed service information for MAINTENANCE PROCEDURES your vehicle. Refer to these Service Manuals before The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle.
MAINTAINING YOUR VEHICLE 685 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
686 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil The oil change indicator system will remind you that it is Identification Symbol time to take your vehicle in for scheduled maintenance. This symbol means that the oil has Refer to the “Maintenance Schedule” for further informabeen certified by the American tion. Petroleum Institute (API).
MAINTAINING YOUR VEHICLE 687 Engine Oil Viscosity — 3.6L/5.7L Engines (1500 Models Only) Engine Oil Viscosity — 5.7L Engine (2500/3500 Models Only) MOPAR® SAE 5W-20 engine oil approved to Chrysler Material Standard MS-6395 or equivalent Pennzoil® or Shell Helix® is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. MOPAR SAE 5W-20 engine oil or equivalent Pennzoil® or Shell Helix® is recommended for all operating temperatures.
688 MAINTAINING YOUR VEHICLE • For 2500/3500 trucks with a 5.7L engine operating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, SAE 5W-30 engine oil is recommended for all operating temperatures. Disposing Of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE 689 quality filters should be used to assure most efficient Engine Air Cleaner Filter Selection service. MOPAR® engine oil filters are a high quality oil The quality of replacement engine air cleaner filters filter and are recommended. varies considerably. Only high quality filters should be used to assure most efficient service.
690 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. • Battery gas is flammable and explosive.
MAINTAINING YOUR VEHICLE 691 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. • The air conditioning system contains refrigerant under high pressure.
692 MAINTAINING YOUR VEHICLE Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. Front Driveshaft Lubrication — 2500/3500 (Four-Wheel Drive Models Only) Refrigerant Recovery And Recycling HFO 1234yf — If Equipped Body Lubrication Lubricate the front driveshaft grease fitting at each oil change.
MAINTAINING YOUR VEHICLE 693 underhood services, the hood latch, release mechanism Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with and safety catch should be cleaned and lubricated. petroleum products such as engine oil, gasoline, etc. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
694 MAINTAINING YOUR VEHICLE To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE 695 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
696 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE 697 Cooling System WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
698 MAINTAINING YOUR VEHICLE Cooling System — Drain Flush And Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old engine coolant (antifreeze). Refer to the “Maintenance Schedule” for the proper maintenance intervals.
MAINTAINING YOUR VEHICLE 699 CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
700 MAINTAINING YOUR VEHICLE (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: have a authorized dealer drain, flush, and refill with OAT coolant (conforming to MS-12106) as soon as possible.
MAINTAINING YOUR VEHICLE 701 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
702 MAINTAINING YOUR VEHICLE To check the coolant level: 1. Open the coolant reservoir. Coolant Reservoir Dipstick 3. Check the coolant level on the dipstick. Opening The Coolant Reservoir 2. Lift and remove the plastic dipstick from the reservoir neck.
MAINTAINING YOUR VEHICLE 703 The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. Advise your service attendant of this.
704 MAINTAINING YOUR VEHICLE • Check the coolant freeze point in the radiator and in • Do not change the thermostat for Summer or Winter the coolant expansion bottle. If engine coolant (antioperation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may freeze) needs to be added, the contents of the coolant result in unsatisfactory engine coolant (antifreeze) expansion bottle must also be protected against freezperformance, poor gas mileage, and increased emising.
MAINTAINING YOUR VEHICLE 705 WARNING! (Continued) high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Brake Fluid Level Check The fluid level of the master cylinder should be checked when performing under the hood service or immediately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir.
706 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
MAINTAINING YOUR VEHICLE 707 For 1500 Model axles, the fluid level should be even with the bottom of the fill hole (within 1/4 in (6.4 mm) of edge of hole) for the FDU215 HD front axle and C235FE rear axle. NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage.
708 MAINTAINING YOUR VEHICLE NOTE: When refilling an axle with a Limited Slip Differ- Automatic Transmission ential, (which requires a Limited Slip Additive), the Selection Of Lubricant Limited Slip Additive should be added before the gear It is important to use the proper transmission fluid to lubricant is added to insure proper additive fill. ensure optimum transmission performance and life. Use Transfer Case only the manufacturer’s specified transmission fluid.
MAINTAINING YOUR VEHICLE 709 CAUTION! (Continued) CAUTION! shudder, and will require more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty.
710 MAINTAINING YOUR VEHICLE CAUTION! Use the following procedure to check the transmission fluid level properly: If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. 1. Monitor the transmission temperature using the EVIC display, and operate the vehicle as required to reach the normal operating temperature. 2. Park the vehicle on level ground.
MAINTAINING YOUR VEHICLE 711 7. Remove the dipstick again and note the fluid level on both sides. The fluid level reading is only valid if there is a solid coating of oil on both sides of the dipstick. Note that the holes in the dipstick will be full of fluid if the actual level is at or above the hole. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature.
712 MAINTAINING YOUR VEHICLE NOTE: To prevent dirt and water from entering the transmission after checking or replenishing fluid, make sure that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Fluid And Filter Changes — Eight-Speed Transmission Fluid And Filter Changes — Six-Speed Transmission Refer to the “Maintenance Schedule” for the proper maintenance intervals.
MAINTAINING YOUR VEHICLE 713 hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your vebody protection. hicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with The following maintenance recommendations will enable clear water. you to obtain maximum benefit from the corrosion resistance built into your vehicle.
714 MAINTAINING YOUR VEHICLE CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
MAINTAINING YOUR VEHICLE 715 Wheel And Wheel Trim Care • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner. NOTE: If your vehicle is equipped with Dark Vapor Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds.
716 MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR® Total Clean, or a Your leather upholstery can be best preserved by regular mild soap solution to a clean, damp cloth and remove cleaning with a damp soft cloth. Small particles of dirt stain. Use a fresh, damp towel to remove soap residue. can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
MAINTAINING YOUR VEHICLE 717 CAUTION! Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR® Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear Cleaning Headlights quarter window equipped with the radio antenna.
718 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth. Seat Belt Maintenance Tri-Fold Soft Tonneau Cover Care For cleaning and protecting the vinyl Tri-Fold Tonneau cover, use MOPAR® Whitewall & Vinyl Top Cleaner and MOPAR® Leather and Vinyl Conditioner/Protectant.
MAINTAINING YOUR VEHICLE 719 To Help Maintain The Appearance Of Your Spray-On Spray-On Bedliners are chemically-resistant to many Bedliner, Follow The Steps Below: different types of chemicals (including gasoline, oil, hydraulic fluids) for short periods of time. If a spill 1. Rinse your truck bed out with water to remove any occurs on your Spray-On Bedliner, rinse the truck out as loose dirt and debris. soon as possible to avoid permanent damage. 2.
720 MAINTAINING YOUR VEHICLE FUSES WARNING! (Continued) WARNING! • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may result in serious personal injury, fire and/or property damage.
MAINTAINING YOUR VEHICLE 721 Power Distribution Center The Power Distribution Center is located in the engine compartment near the battery. This center contains cartridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
722 MAINTAINING YOUR VEHICLE Cavity F07 F08 F10 F10 Cartridge Fuse 40 Amp Green 40 Amp Green (Cummins Diesel) 20 Amp Yellow (1500 LD Diesel) 40 Amp Green (Cummins Diesel) 30 Amp Pink (1500 LD Diesel) 40 Amp Green 50 Amp Red F11 F12 F13 F14 30 Amp Pink 40 Amp Green 40 Amp Green 40 Amp Green F09 Micro Fuse Description Starter Solenoid Emissions Diesel – If Equipped Diesel Fuel Heater – If Equipped Body Controller / Exterior Lighting #2 Body Controller / Exterior Lighting #2 – If Equipped with Stop/S
MAINTAINING YOUR VEHICLE 723 Cavity F15 F19 F20 F21 F22 F23 F24 F25 F25 F26 F28 F29 F30 F32 Cartridge Fuse 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink 20 Amp Yellow 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink 20 Amp Yellow 20 Amp Yellow 30 Amp Pink 30 Amp Pink Micro Fuse Description Electric Park Brake Right Side – If Equipped SCR – If Equipped Passenger Door Module Drive Train Control Module Engine Control Module Body Controller #1 Driver Door Module Front Wiper Low Speed Front Wipe
724 MAINTAINING YOUR VEHICLE Cavity F33 F34 F35 F36 F37 F38 F39 F41 F42 F43 F44 F46 F47 F49 Cartridge Fuse 20 Amp Yellow 30 Amp 30 Amp 30 Amp 30 Amp 30 Amp 30 Amp Micro Fuse Pink Pink Pink Pink Pink Pink 10 Amp Red 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red 10 Amp Red 10 Amp Red Description Cummins Diesel Fuel Heater #1 – If Equipped / Rear Blower – If Equipped Vehicle System Interface Module #2 – If Equipped Sunroof – If Equipped Rear Defroster– If Equipped Cummins Diesel Fuel Heater #2 If Equippe
MAINTAINING YOUR VEHICLE 725 Cavity F50 F51 F52 F53 F54 F55 F56 F57 F58 F60 F61 Cartridge Fuse Micro Fuse 20 Amp Yellow 10 Amp Red 5 Amp Tan 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 20 Amp Yellow (Gas Engine) / 25 Amp Natural (Cummins Diesel Engine) 15 Amp Blue 20 Amp Yellow Description Air Suspension Control Module – If Equipped Ignition Node Module / Keyless Ignition Battery Sensor Trailer Tow – Left Turn/Stop Lights Adjustable Pedals E38 Radio – If Equipped Additional Dies
726 MAINTAINING YOUR VEHICLE Cavity F62 F63 F64 F65 F66 F67 F69 F70 F71 F72 Cartridge Fuse Micro Fuse 10 Amp Red 20 Amp Yellow 25 Amp Natural 10 Amp Red 10 Amp Red 10 Amp Red 15 Amp Blue 30 Amp Green 25 Amp Natural 10 Amp Red Description Air Conditioning Clutch Ignition Coils (Gas), Urea Heater (Cummins Diesel) Fuel Injectors / Powertrain USB interface Sunroof / Passenger Window Switches / Rain Sensor CD / DVD / Bluetooth Hands-free Module – If Equipped Mod SCR 12V (Cummins Diesel) – If Equipped Fuel Pu
MAINTAINING YOUR VEHICLE 727 Cavity F74 Cartridge Fuse F75 F76 F77 Micro Fuse 20 Amp Yellow (Gas Engine & 1500 LD Diesel) / 10 Amp Red (Cummins Diesel Engine) 10 Amp Red 10 Amp Red 10 Amp Red F78 F79 F80 F81 F82 F84 10 Amp Red 15 Amp Blue 10 Amp Red 20 Amp Yellow 10 Amp Red 15 Amp Blue Description Brake Vacuum Pump Gas/Diesel – If Equipped Coolant Temperature Valve Actuator Antilock Brakes/Electronic Stability Control Drivetrain Control Module/Front Axle Disconnect Module Engine Control Module / Ele
728 MAINTAINING YOUR VEHICLE Cavity F85 F86 F87 Cartridge Fuse Micro Fuse 10 Amp Red 10 Amp Red 10 Amp Red F88 F90/F91 F93 F94 F95 F96 F97 15 Amp Blue 20 Amp Yellow 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red 25 Amp Natural F98 F99 25 Amp Natural 10 Amp Red Description Airbag Module Airbag Module Air Suspension-If Equipped / Trailer Tow / Steering Column Control Module Instrument Panel Cluster Power Outlet (Rear seats) Customer Selectable Cigar Lighter Shifter / Transfer Case Module Rear Camera /
MAINTAINING YOUR VEHICLE 729 Cavity F101 Cartridge Fuse F104 Micro Fuse 15 Amp Blue 20 Amp Yellow Description Electrochromatic Mirror / Smart High Beams – If Equipped Power Outlets (Instrument Panel/Center Console) CAUTION! CAUTION! (Continued) • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched.
730 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the negative cable from battery. Interior Bulbs Bulb Number TS 212–9 Overhead Console Lamps Dome Lamp 7679 For lighted switches, see your authorized dealer for replacement instructions. • Any time you store your vehicle or keep it out of service (i.e.
MAINTAINING YOUR VEHICLE 731 Premium Bi Halogen Projector Headlamp Low Beam Premium Bi Halogen Projector Headlamp High Beam Front Turn Signal Lamp (Premium Headlamp) Fog Lamp (Horizontal shape) Fog Lamp (Vertical shape) Center High Mounted Stop Lamp (CHMSL) Rear Cargo Lamp Bulb Number HIR2 9005 LED (Serviced at Authorized Dealer) 9145 9006 921 921 LED Center High Mounted Stop Lamp (CHMSL)/Cargo Lamp Cab Roof Marker Lamps Base Rear Tail/Turn and Stop Lamp Premium Rear Tail/Turn and Stop Lamp Premium Bac
732 MAINTAINING YOUR VEHICLE BULB REPLACEMENT 5. Remove the upper radiator seal from the vehicle. NOTE: Lens fogging can occur under certain atmo- 6. Remove the two headlamp assembly attachment screws. spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Base Quad / Premium Bi-Halogen: Low Beam Headlamp, High Beam Headlamp, Front Park And Turn — If Equipped 1.
MAINTAINING YOUR VEHICLE 733 7. Reach into the front wheel house ahead of the front wheel, remove the fastener, and lift the cover over the access hole in the front of the wheel house splash shield. Access to the rear of the lamp can be gained through this access hole. 8. Reach through the access hole of the wheel house splash shield and lift the slide lock upward far enough to disengage it from the lock post on the back of the front lamp unit housing. Slide Lock 9. Remove the headlamp assembly.
734 MAINTAINING YOUR VEHICLE 10. Disconnect the wiring harness connectors from the Fog Lamps — If Equipped bulb socket. 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 11. Replace bulb(s) as necessary. CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Always use the correct bulb size and type for replacement.
MAINTAINING YOUR VEHICLE 735 2. Pull the outboard side of the lamp rearward far enough to unsnap the two receptacles on the outboard 1. Remove the two screws that pass through the bed side of the lamp housing from the two plastic snap sheetmetal. post retainers in the outer box side panel. Rear Tail/Stop, Turn Signal And Backup Lamps 7 Tail Lamp Screw Locations Pulling Out The Tail Lamp 3. Disconnect the wiring harness connectors from the bulb socket.
736 MAINTAINING YOUR VEHICLE 4. Rotate the bulb socket counterclockwise 1/4 turn to unlock it from the housing. 5. Pull the bulb straight out of the socket. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. 6. Reverse the procedure to install the bulb and housing. Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp CHMSL Mounting Screw Locations 2.
MAINTAINING YOUR VEHICLE 737 4. Pull the desired bulb straight from the socket. CHMSL Connector Location 3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing.
738 MAINTAINING YOUR VEHICLE CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 739 2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. 3. Pull the bulb straight from it’s socket and replace.
740 MAINTAINING YOUR VEHICLE Rear Lamp Bar ID Marker (Dual Rear Wheels) — If 2. Turn the socket ¼ turn counterclockwise to access the bulb. Equipped 1. Loosen the two screws and the housing to gain access 3. Pull the bulb straight out from the socket. to the bulb sockets. 4. Reverse the procedure for installation of the bulbs and housing.
MAINTAINING YOUR VEHICLE 741 Side Marker Lamps (Dual Rear Wheels) — If Equipped 2. Pull the entire assembly from the fender. 3. Turn the socket ¼ turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the procedure for installation of the bulbs and housing. 7 Side Marker Lamp Locations 1. Push rearward on the side marker lamp assembly.
742 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 1500 Regular Cab Longbed/Crew Quad Cab Models (Optional) 2500/3500 Shortbed Models 2500/3500 Longbed Models Engine Oil With Filter 3.6L Engine (We recommend you use SAE 5W-20, API Certified) 5.7L Engines (We recommend you use SAE 5W-20, API Certified) 5.
MAINTAINING YOUR VEHICLE 743 Cooling System 3.6L Engine (We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula that meets the requirements of Chrysler Material Standard MS-12106.) 5.7L Engine – 1500 Models (We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula that meets the requirements of Chrysler Material Standard MS-12106.) 5.
744 MAINTAINING YOUR VEHICLE 6.4 Liter Engine – 2500/3500 Models w/Heavy Duty ( We recommend yo use MOPAR® Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula that meets the requirements of Chrysler Material Standard MS-12106. U.S. 19.2 Quarts Metric 18.2 Liters FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 5.7 Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology).
MAINTAINING YOUR VEHICLE 745 Component Engine Oil – 5.7L Engine For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs/(6,350 kg.) Engine Oil – 6.4L Engine Oil Filter Spark Plugs – 3.6L Engine Spark Plugs – 5.7L Engine Spark Plugs – 6.4L Engine Fuel Selection – 3.
746 MAINTAINING YOUR VEHICLE Component Fuel Selection – 5.7L Engines Fuel Selection – 6.
MAINTAINING YOUR VEHICLE 747 Component Rear Axle – 1500 Models Front and Rear Axle – 2500/3500 Models Brake Master Cylinder Power Steering Reservoir – 2500/3500 Models Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Synthetic Gear Lubricant SAE 75W-140 (MS8985). Limited-Slip Rear Axles require the addition of 5 oz. (148 ml) MOPAR® Limited Slip Additive (MS-10111). We recommend you use Synthetic, GL-5 SAE, 75W-90. Limited slip additive is not required for Limited-Slip Rear Axles.
M A I N T E N A ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . .753 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 750 MAINTENANCE SCHEDULES than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)/Oil Change Required” in indicator system. The oil change indicator system will “Understanding Your Instrument Panel” for further inremind you that it is time to take your vehicle in for formation. scheduled maintenance.
MAINTENANCE SCHEDULES 751 M A • Check tire pressure and look for unusual wear or dam- I age. Rotate tires at the first sign of irregular wear, even if N • Change Engine Oil at 4000 miles (6,500 km) if the T it occurs before the oil indicator system turns on. E vehicle is operated in a dusty and off road environment.
M A I N T E N A N C E S C H E D U L E S 8 752 MAINTENANCE SCHEDULES Required Maintenance Refer to the Maintenance Schedules on the following pages for required maintenance. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • Inspect battery and clean and tighten terminals as required.
MAINTENANCE SCHEDULES 753 M Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle surfaces. If gear oil leakage is suspected, check the fluid level. If using your vehicle for police, taxi, fleet, off-road or frequent trailer towing, change axle fluid.
S C H E D U L E S 8 Inspect the brake linings, replace as necessary. Adjust parking brake as necessary. Inspect transfer case fluid. Additional Maintenance Replace engine air filter. Replace spark plugs (3.6L engine).** Replace spark plugs (5.7L engine).
Replace spark plugs (6.4L engine).** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change automatic transmission fluid and filter(s) (six-speed automatic only), if using your vehicle for police, taxi, fleet, or frequent trailer towing.
S C H E D U L E S 8 Change automatic transmission fluid and filter (six-speed automatic only). Inspect the transfer case fluid, change for any of the following: police, taxi, fleet, or frequent trailer towing. Change the transfer case fluid. Inspect and replace PCV valve if necessary.
MAINTENANCE SCHEDULES 757 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .761 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .763 ▫ Prepare For The Appointment. . . . . . . . . . . . .761 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .763 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .761 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
760 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .767 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .767 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .767 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 761 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
762 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 763 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
764 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 765 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– operating at its best. 9153), or go to http://www.safercar.
766 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 767 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
768 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
770 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .699 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .577 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .571 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .180 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .78 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 771 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .406 Special Additives . . . . . . . . . . . . . . . . . . . . . . .709 Axle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .706 Axle Lubrication (Axle Fluid) . . . . . . . . . . . . . . . . .706 Back-Up Camera. . . . . . . . . . . . . . . . . . . . . . . . . .202 Bar, Stabilizer/Sway System. . . . . . . . . . . . . . . . . .464 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
772 INDEX Certification Label. . . . . . . . . . . . . . . . . . . . . . . . .579 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . .531 Check Engine Light (Malfunction Indicator Light) . . . .278 Checking Your Vehicle For Safety . . . . . . . . . . . . . .115 Checks, Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . .115 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Cigar Lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 773 Dipsticks Power Steering . . . . . . . . . . . . . . . . . . . . . . . . .511 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . .670 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . .701 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . . .39 Door Opener, Garage. . . . . . . . . . . . . . . . . . . . . . .207 Driving Off-Pavement . . . . . . . . . . . . . . . . . . . . . . . . . .
774 INDEX Compartment Identification . . . . . . . . . . . . . . . .678 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . . . .744 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . . . .116 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . .387 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . .568 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .659 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .685 Oil Filler Cap . . . . . . . . .
INDEX 775 Fluid Leaks . . . . . . . . . . . . . . . . . . Fluid Level Checks Brake . . . . . . . . . . . . . . . . . . . . . Power Steering . . . . . . . . . . . . . . Fluids, Lubricants and Genuine Parts Fog Lights . . . . . . . . . . . . . . . . . . . Fold Flat Load Floor . . . . . . . . . . . . Four-Way Hazard Flasher . . . . . . . . Four Wheel Drive . . . . . . . . . . . . . . Freeing A Stuck Vehicle . . . . . . . . . . Front Axle (Differential). . . . . . . . . . Fuel . . . . . . . . . . . . . . . . .
776 INDEX Grocery Bag Retainer. . . . . . . . . . . . . . . . . . . . . . .236 Gross Axle Weight Rating . . . . . . . . . . . . . . . . . . .582 Gross Vehicle Weight Rating. . . . . . . . . . . . . . . . . .582 Guide, Body Builders . . . . . . . . . . . . . . . . . . . . . . . .6 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .579 Hazard Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . .486 Hazard Warning Flasher . . . . . . .
INDEX 777 Integrated Trailer Brake Controls . . . . . . . . . . . . . .593 Interior Appearance Care . . . . . . . . . . . . . . . . . . . .716 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .168 Intermittent Wipers (Delay Wipers). . . . . . . . . . . . .174 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Inverter Outlet (115V) . . . . . . . . . . . . . . . . . . . . . .225 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . .621 Jump Starting .
778 INDEX Electronic Stability Program (ESP) Indicator . . . . .527 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 Four-Wheel Drive Indicator . . . . . . . . . . . . . . . .432 Hazard Warning Flasher . . . . . . . . . . . . . . . . . .617 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 High Beam Indicator . . . . . . . .
INDEX 779 Malfunction Indicator Light (Check Engine). . . . . . .682 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . .766 Manual Transmission Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .708 Lubricant Selection . . . . . . . . . . . . . . . . . . . . . .746 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .569 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
780 INDEX Onboard Diagnostic System . . . . . . . . . . . . . . . . . .681 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .681 Operator Manual (Owner’s Manual) . . . . . . . . . . . . .4 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . .135 Overdrive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .415 Overdrive OFF Switch . . . . . . . . . . . . . . . . . . . . . .415 Overhead Console. . . . . . . . . . . . . . . . . . . . . . . . .205 Overheating, Engine . . . . .
INDEX 781 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . .356 Rain Sensitive Wiper System . . . . . . . . . . . . . . . . .176 Ramp Travel Index . . . . . . . . . . . . . . . . . . . . . . . .466 Rear Axle (Differential) . . . . . . . . . . . . . . . . . . . . .706 Rear Cargo Area Utility Rails . . . . . . . . . . . . . . . . .255 Rear ParkSense System . . . . . . . . . . . . . . . . . . . . .185 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . . .
782 INDEX Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . .718 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . . .65 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Adjustable Upper Shoulder Anchorage . . . . . . . . .61 And Pregnant Women . . . . . . . . . . . . . . . . . . . . .66 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . .82 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Front Seat . . . . . . .
INDEX 783 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Signals, Turn. . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Sliding Rear Window Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . . .552 Snow Plow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .601 Snow Tires . . . . . . . . . . . . . . . . . . . .
784 INDEX Tire and Loading Information Placard . Tire Markings . . . . . . . . . . . . . . . . . . Tires . . . . . . . . . . . . . . . . . . . . . . . . Aging (Life of Tires) . . . . . . . . . . . Air Pressure . . . . . . . . . . . . . . . . . Chains . . . . . . . . . . . . . . . . . . . . . Compact Spare . . . . . . . . . . . . . . . Dual . . . . . . . . . . . . . . . . . . . . . . General Information . . . . . . . . . . . High Speed . . . . . . . . . . . . . . . . . Inflation Pressures . . . . . . . . .
INDEX 785 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . .581 Cooling System Tips . . . . . . . . . . . . . . . . . . . . .601 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .585 Minimum Requirements . . . . . . . . . . . . . . . . . .590 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 Trailer and Tongue Weight . . . . . . . . . . . . . . . . .589 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .598 Trailer Towing Guide. . . .
786 INDEX Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .486 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . .715 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . .715 Wheel Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .657 Winch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .490 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .494 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
14D241-126-AC Third Edition Printed in U.S.A.
