Owners manual

ManualsBrandsRampage ManualsAutomotive139935 Trailview Frameless Soft Top Fits 07-18 Wrangler (JK)

Installation Instructions

I - Sheet Number I-TVR-01 Rev. D

TrailView Soft Top

™

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

Important Safety Information

NOTE: Actual product may vary from illustration.Contents

Soft Top Assembly x1

(main fabric, side windows, rear windows)

End Clamp Main Body x2 Door Surround Set x1 Tailgate Bar x1

Allen Key x2

Hook & Loop Strip x2

(for door surround)

(SM) Short Middle Knobs x2

(LF) 60mm Long Front Knobs x2

(LR) 70mm Long Rear Knobs x2

Retractable Trailview

Hardware x1

Self-Drilling Screws x30

Short Middle Knobs x2

Tailgate Bar x1

Anti-Puddle Poles x2

End Clamp Backing x2

Tools Required

Torx Bits Allen Wrench

Safety Glasses

Ratchet and extensionsPhillips screwdriver

Pre-Installation Requirements

• Remove existing hard or soft top. For OEM (original/factory) soft tops, also remove:

• Windshield header bar

• Tube frame hardware from roll bar

• Side door surrounds

• Rear window, tailgate bar, tailgate clips

• Periodically check all components for tightness.

• Be sure to where safety goggles while installing.

• When using power tools, read and understand all operating instructions

Page 1 of 11

Summary of content (11 pages)

PAGE 1
Installation Instructions I - Sheet Number I-TVR-01 Rev. D TrailView Soft Top™ For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • Periodically check all components for tightness. • Be sure to where safety goggles while installing.
PAGE 2
Installation Steps NOTE: Actual application may vary slightly from illustrations. Unfold your new TrailView Soft Top™ and separate the packaged pieces. TIP: Driver’s side pieces are sealed in green plastic packaging. Passenger’s side pieces are sealed in clear plastic packaging. Set aside the windows for a later step and take care not to scratch them. 1 TIP: The factory door surrounds cannot be used. Use the Rampage door surround kit that has been designed specifically for the TrailView Soft Top™.
PAGE 3
Installation Steps NOTE: Actual application may vary slightly from illustrations. 4-Door Model ONLY Join front surround section to rear surround section with a self-drilling screw. Insert middle plastic piece into front door surround section and secure with a self-drilling screw. 7 8 Insert corner piece of vertical upright into assembled front and rear surround. Slide the rear bracket onto the rear surround section. 9 10 Repeat this section (steps 1-11) to assemble passenger’s side door surround.
PAGE 4
Installation Steps NOTE: Actual application may vary slightly from illustrations. TIP: Make sure the rubber gasket at the top of the windshield is correctly sealed against the front surround section. See photo below for proper fit: Inspect the clearance between top of windshield frame and door surround. Check that the factory foam seal is in place. 14 15 Fit door surround mount plate on top of door surrounds. Secure the mount plate to the roll cage using turn-knobs in the holes.
PAGE 5
Installation Steps NOTE: Actual application may vary slightly from illustrations. Place provided latch as shown and reattach with the Torx T25 bolt from the previous step. Fold back the hardware tubes of the header channel assembly then insert into the main fabric. Secure with snaps as shown. 22 23 TIP: It may be helpful to have a second person for this step. Place the top face down and re-fold, beginning with the rear window portion. Tuck the plastic strip behind latches and along side rails.
PAGE 6
Installation Steps NOTE: Actual application may vary slightly from illustrations. TIP: Lift up the main fabric for easier access to the brackets. Line up the brackets then secure with the counter-sink Allen head screw and nylon lock-nut. See photos below for proper fit: 28 Fold the top toward the windshield to close. Secure using latches. 29 Unfold the cover fabric then pull over sound bar and roll cage, working toward the rear of the vehicle. 31 Attach the latch to the metal flange.
PAGE 7
Installation Steps NOTE: Actual application may vary slightly from illustrations. 4-Door Model ONLY Locate the ceiling adjustment straps at the corners of the ceiling panel. Wrap the straps around the roll bar and seatbelt stud toward the inside of the Jeep, then back up to the strap adjustment buckle. Tighten and repeat for the passenger side. Adjust each side to position the top evenly. See diagram below: 33 2-Door Model ONLY Locate the ceiling adjustment straps at the corners of the ceiling panel.
PAGE 8
Installation Steps NOTE: Actual application may vary slightly from illustrations. Secure the side windows to the main cover fabric by zipping into place. Repeat for the rear window. See the diagram below for the proper installation sequence: 35 Insert the side-rear-quarter black plastic piece into the fabric sleeve-pocket located inside your rear window pieces.
PAGE 9
Installation Steps NOTE: Actual application may vary slightly from illustrations. Assemble the brackets by sliding the plastic backing onto the metal extrusion. Secure with two screws in each bracket using pre-drilled holes. 37 Install the Tailgate Bar brackets by hooking the front edge over the belt rail sheet metal. Close the clamp with downward pressure while pulling the backing tight. The clamp will pop and lock onto the underside of the tube edge.
PAGE 10
Installation Steps NOTE: Actual application may vary slightly from illustrations. Insert the fiberglass anti-puddle poles into the built-in pockets at the rear-ceiling of the top. Flex the poles for a secure fit. 39 Fit the rubber gasket onto the top of the tailgate. Push the gasket down over the top edge of the tailgate to seal tightly. See photo below for proper orientation: 40 Zip the rear window closed.
PAGE 11
Installation Steps NOTE: Actual application may vary slightly from illustrations. Attach the main deck belt rail plastic into the upper door surround from front to back. Start at the windshield header. Tip: Make sure rear panel zippers are lined up on both sides. 42 43 Secure the belt rail plastic of the side windows from front to back, starting on the back top of the door surrounds. Hook the belt rail plastic to the back section of the door surround.