DANGER READ AND OBEY ALL SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING TOOL.
SAFETY INTRODUCTION DANGER DANGER THIS TOOL IS TO BE USED ONLY BY PROPERLY TRAINED OPERATORS. ATTEMPTING TO HANDLE OR OPERATE THE T2 GAS POWERED TOOL WITHOUT PROPER TRAINING CAN RESULT IN SERIOUS INJURY TO THE OPERATOR OR BYSTANDERS. ! ! ! ! ! ! ! ! ! Read, understand and follow the instructions in the tool manual before attempting to use the tool. Operators and Bystanders must wear eye and hearing protection. Never close tool with hand over the fastener loading end of the tool.
TABLE OF CONTENTS SAFETY INTRODUCTION 2 CONTENTS 3 SAFETY INSTRUCTIONS 4-7 FASTENING APPLICATIONS 8 TOOL OPERATING INSTRUCTIONS 9 PARTS SCHEMATIC 10-11 PARTS LIST 12-13 SERVICING/TROUBLESHOOTING 14 WARRANTY 15 TABLE OF CONTENTS 3
DANGER SAFETY INSTRUCTIONS Preparation For Fastening Acceptable Base Materials The gas powered T2 tool is suitable for use in the following base materials only: • Poured Concrete • Structural Steel • Concrete Block and Horizontal Joints in Brick or Masonry Walls Solid Concrete and Precast Concrete Never attempt to fasten into any other type of material. Fastening into other materials can cause blindness or other serious injury.
DANGER SAFETY INSTRUCTIONS Fuel Cells and Batteries Fuel Cells • The fuel cell must be used at temperatures between -5° C (23° F) and 49° C (120° F). • At the beginning of each fastening cycle, a measured amount of gas is injected into the combustion chamber. • The fuel cell is designed with an internal reservoir that is under pressure by a propellant. • When the fuel cell is empty, a small amount of propellant remains inside the cell.
DANGER SAFETY INSTRUCTIONS Installing the battery • Insert the battery into the tool as shown on the right with the clip toward the rear. • Note the LED light on the right side of the handle. After installing the battery: Battery is shown in the “no contact” position. Push it fully down to lock it in place. - If the light flashes green the tool is powered. - If the light flashes red the battery requires charging. - If the light is solid green and the fan is running, the tool is ready to use.
DANGER SAFETY INSTRUCTIONS FAILURE TO FOLLOW INSTRUCTIONS CAN CAUSE INJURY TO THE TOOL OPERATOR OR TO BYSTANDERS. • Use the tool only in well ventilated areas. • Always hold the tool at right angles to the work surface. • Never attempt to make a fastening at an angle to the work surface.
FASTENING APPLICATIONS 3" MIN. FASTENING APPLICATIONS Your T2 tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool and fasteners, as well as help you perform these fastening operations safely and effectively. T2 fastenings are permanent fastenings so attempting to remove a fastener from concrete or steel may result in a serious injury. 3" MIN.
TOOL OPERATING INSTRUCTIONS TOOL OPERATION Insert battery Always check the tool first to make sure that it does not contain a fastener. If the tool contains a fastener from a previous application, remove both the battery and the fuel cell before attempting to remove the fastener. Operating the T2 Tool 1. Insert a charged battery into the tool with the battery clip toward the rear of the tool. 2. Insert the Ramset fuel cell into the tool as described on page 6. Insert fuel cell 3.
PARTS SCHEMATIC RAMSET T2 TOOL SCHEMATIC PARTS SCHEMATIC 10
PARTS SCHEMATIC RAMSET T2 TOOL SCHEMATIC (continued) PARTS SCHEMATIC 11
PARTS LISTS RAMSET T2 TOOL PARTS LISTS KEY PART NUMBER 1 336920 2 336900 3 B0060A 4 339000 5 B0070 6 B0061A 7 B0040 8 7505164 9 900525A 10 401356 11 900470 12 401355 13 404601 14 B0078 15 403992 16 403167 17 B0044A 17 B0057 18 339010 19 333180 21 337700 22 336510 23 333220 24 B0038 25 B0178 26 333250 27 B0068 28 B0031A 28A B0034A 29 B0053 31 B0042 32 B0054A 33 B0037A 35 B0105 PARTS LIST 12 DESCRIPTION GRILL CAP AIR FILTER CAP SCREWS M5-30 W/WASHER CAP ASSEMBLY SPARK PLUG WIRE PC BOARD S
PARTS LIST RAMSET T2 TOOL PARTS LISTS (continued) KEY PART NUMBER 37 334020 38 337440 39 333380 40 404619 41 404490 42 404385 43 B0134 45 010422 46 333450 47 333460A 49 333480A 51 336870 53 B0062A 54 010900 55 B0144 56 EM150330 57 EM150340A — B0058 — B0072 — B0073 — B0057 * T2OM * 334000 * 7505142 DESCRIPTION BATTERY SUPPORT RUBBER HANDLE GRIP KNOB ASSEMBLY INSULATOR TRIGGER SWITCH LIGHT CONDUIT SPARK UNIT ASSEMBLY, MEFI-R EFI JUNCTION BOARD TRIGGER ASSEMBLY FEED ASSEMBLY (INCLUDES:
SERVICING/TROUBLESHOOTING FOR SERVICING REQUIRED BUT NOT LISTED IN THIS MANUAL, PLEASE CONTACT YOUR LOCAL DISTRIBUTOR Filters and Battery Contacts Cleaning the filters and battery contacts on a regular basis will help make your tool work more efficiently. To clean the filters • Remove the cover and the filters. • Lightly tap the filters to remove any dust. • Replace the filters if damaged. • Replace the filters and the cover.
WARRANTY T2 TOOL WARRANTY AND LIMITATIONS Ramset warranty that new T2 power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below, after the date of delivery to the original user. TWO-YEAR WARRANTY A two-year warranty will apply to all parts, except those listed below as normal wearing parts, or parts which are specifically covered by an extended warranty.
FOR TOOL REPAIR SERVICE CONTACT YOUR LOCAL AUTHORIZED RAMSET DISTRIBUTOR OR TO FIND YOUR NEAREST RAMSET TOOL REPAIR CENTER VISIT OUR WEB SITE AT WWW.RAMSET.COM OR CALL 800-241-5640 Concrete Fastening Systems Glendale Heights, IL 60139 800-RAMSET6 (1-800-726-7386) www.ramset.com Buy with Confidence... Buy From Your Authorized Distributor AN ILLINOIS TOOL WORKS COMPANY © ILLINOIS TOOL WORKS 2008 PRINTED IN THE U.S.A. REVISED 11/08 Form No.