User Manual

ManualsBrandsRamsey Winch ManualsFor the carQM-9000

Congratulations!

You have purchased the finest winch available in its service

class. The Quick Mount

is a detachable winch. It can be

easily mounted to the front or rear of a vehicle for self recovery

and other applications. It allows one winch to be used on

multiple vehicles, and can be quickly installed and removed to

avoid extra vehicle weight.

The Quick Mount

comes with a remote control switch,

anti-theft locking pin and a hawse fairlead. Front mount

requires a front receiver mounting kit. Optional 5 ft., 20 ft. or

24 ft. battery cables for front or rear mounting are available.

The Quick Mount

features a highly efficient 3 stage planetary

gear set which transmits torque from a series wound D.C.

motor. A positive clutch allows free spooling for quick cable

deployment. An automatic load holding brake is designed to

hold the full rated capacity of the winch. It was designed and

manufactured to provide you with the utmost in utility. As with

any device that combines power and movement in its use,

there are dangers if improperly used. At the same time, there

are easier and faster ways for getting the job done if certain

precautions are taken first.

Please read this manual carefully. It contains useful ideas in

obtaining the most efficient operation from your Ramsey

Winch and safety procedures you need to know before begin-

ning use.

When you follow our guidelines for operation, your Ramsey

Winch will give you many years of satisfying service. Thank

you for choosing Ramsey. You will be glad you have one

working for you.

Ramsey Winch Company

Owner’s Manual

Front Mount Electric Winch

Model Quick Mount 9000/9500

QUICK MOUNT 9000

Layer of Cable 1 2 3 4 5

Rated Line Pull Per Layer

(lbs) 9,000 7,300 6,200 5,400 4,700

(kg) 4,070 3,300 2,800 2,440 2,130

Cumulative Cable Capacity

Per Layer

(5/16" - 8mm - dia. Cable)

(ft)* 15 35 60 90 105

(m)* 4 10 18 27 32

Line Pull First Layer

(lbs) NO 2,000 4,000 6,000 9,000

(kg)

LOAD 900 1,810 2,720 4,070

Line Speed First Layer

(FPM) 29 15 11 9 7

(MPM) 8.8 4.6 3.3 2.7 2.1

Amp Draw (12V)

90 190 245 315 400

QUICK MOUNT 9500

*DEPENDS ON CABLE BEING UNIFORMLY WOUND ONTO DRUM.

Ramsey performance data is compiled from actual winch testing.

Please Note: Ramsey Quick MountTM series winches are

designed for front and rear mount vehicle use. The winches

are not designed for and should not be used in industrial

applications (car haulers /carriers, wreckers, hoisting, etc.),

and Ramsey does not warrant them to be suitable for such

use. Ramsey makes a separate, complete line of winches for

industrial/commercial use. Please contact the factory for

additional information.

CAUTION: Read and understand this manual before installation and operation of winch. See Safety Precautions.

Layer of Cable 1 2 3 4 5

Rated Line Pull Per Layer

(lbs) 9,500 7,700 6,500 5,700 4,900

(kg)

4,309 3,480 2,940 2,580 2,210

Cumulative Cable Capacity

Per Layer

(5/16" - 8mm - dia. Cable)

(ft)* 15 34 58 86 100

(m)* 4 10 17.5 26 30.5

Line Pull First Layer

(lbs) NO 2,000 4,000 6,000 8,000

(kg) LOAD 900 1,810 2,720 3,620

24V 29 16 13 10 9

12V

10.7 5.1 3.8 3.2 2.7

12V

97 180 260 335 395

24V

8.8 4.9 4.0 3.0

2.7

9,500

4,309

2.3

2.4

430

(FPM)

12V 34.5 16.7 12.7 10.6 9 7.8

45 95 128 165 192 212

Line Speed First Layer

(MPM)

AMP DRAW

Summary of content (12 pages)

PAGE 1
Ramsey Winch Company Owner’s Manual Front Mount Electric Winch Model Quick Mount 9000/9500 QUICK MOUNT 9000 Layer of Cable Rated Line Pull Per Layer Cumulative Cable Capacity Per Layer (5/16" - 8mm - dia. Cable) Line Pull First Layer Line Speed First Layer 1 2 3 (lbs) 9,000 7,300 6,200 5,400 4,700 (kg) 4,070 3,300 2,800 2,440 2,130 (ft)* 15 35 60 90 105 (m)* 4 10 18 27 32 (lbs) NO 2,000 4,000 6,000 9,000 (kg) LOAD 900 1,810 2,720 4,070 (FPM) 29 15 11 (MPM) 8.8 4.
PAGE 2
Contents Performance Specifications .....................................Front Cover Safety Precautions.................................................................. 2 Tips for Safe Operation ........................................................... 2 Techniques of Operation ......................................................... 3 Assembling Your Winch.......................................................... 4 Electrical Connections ............................................................
PAGE 3
P. To respool correctly, it is necessary to keep a slight load on the cable. This is accomplished by (wearing gloves) holding the cable with one hand and the remote control with the other, starting as far back and in the center as you can, walking up keeping load on the cable as the winch is powered in. Do not allow the cable to slip through your hand and do not approach the winch too closely. Turn off the winch and repeat the procedure until all the cable except a few feet is in.
PAGE 4
Neat, tight spooling avoids cable binding. Cable binding occurs when a cable under load pulls down into the layer below, becoming pinched between two other wraps of cable. If this happens, alternately power the winch in and out a few inches. Do not attempt to work a bound cable under load; free by hand. When pulling a heavy load, place a blanket, jacket or tarpaulin over the cable five or six feet from the hook. It will slow the snap back in the event of a broken cable.
PAGE 5
PAGE 6
Electrical Connections Remote Control Switch Operation For normal self recovery work, your vehicle’s existing electrical system is adequate. Your battery must be kept in good condition. A fully charged battery and proper connections are essential. The remote control switch is waterproof and has push button stations on either side. It is designed this way to prevent quick winch reversals which lead to premature solenoid failure.
PAGE 7
Maintenance Cable Installation All moving parts are permanently lubricated with high temperature lithium grease at the time of assembly. Under normal conditions factory lubrication will suffice. 1. Unwind the new cable by rolling it out along the ground to prevent kinking. 2. Remove the old cable and observe the manner in which it is attached to the cable drum. Lubricate cable periodically using light penetrating oil. Inspect cable for broken strands and replace if necessary.
PAGE 8
Troubleshooting Guide CONDITION MOTOR RUNS IN ONLY ONE DIRECTION POSSIBLE CAUSE Defective solenoid or stuck solenoid Jar each solenoid to free contacts. Check each solenoid by applying 12 volts to coil-terminal (it should make an audible click when energized). Defective remote control switch Disengage winch clutch, remove remote control switch from the socket and jump pins at 8 and 4 o'clock. Motor should run. Jump pins at 8 and 10 o'clock. Motor should run.
PAGE 9
QUICK MOUNT 9000 17 45 43 18 16 38 41 4 40 30 7 25 44 3 37 9 46 22 21 27 15 46 1 14 6 2 13 42 35 19 34 29 12 26 8 20 28 20 23 11 22 46 47 39 32 42 36 10 48 5 31 Item Qty. Parts No.
PAGE 10
QUICK MOUNT 9500 17 45 43 18 16 38 41 4 40 30 7 25 44 3 37 9 46 22 21 27 15 46 1 14 6 2 13 42 35 19 34 29 12 26 8 20 28 20 23 11 22 46 47 39 32 42 36 10 48 5 31 Item Qty. Parts No. No.
PAGE 11
Solenoid Assembly Parts List: QM 9000/9500 278180 Item No. 1 2 3 4 5 6 7 8 9 10 12v Qty. Part No. 1 2 1 1 1 6 3 2 1 1 289195 289196 316101 316103 413078 414880 416207 416227 430022 440138 QM 9000/9500 Description WIRE ASSEMBLY - #2 GA 13.25" MOTOR LEAD WIRE ASSEMBLY - #2 GA 14.
PAGE 12
Warranty Information Ramsey Winches are designed and built to exacting specifications. Care and skill go into every winch we make. If the need should arise, the warranty procedure is outlined on the back of your self-addressed postage paid warranty card. Please read and fill out the enclosed warranty card and send it to Ramsey Winch Company. If you have any problems with your winch, please follow instructions for prompt service on all warranty claims.