Use and Care Manual
THANK YOU FOR PURCHASING A
Ramsond Mono-Crystalline PV
Solar Panel
You are now one step closer to a sustainable energy system; when
installed properly, you will be guaranteed to years of reliable, high
quality power at very low cost.
Come with
IP65 RATED JUNCTION BOX,
pre-wired with MC4 CONNECTORS &
34” of Heavy Duty cable
Come with
CABLE-READY
IP65 RATED
JUNCTION BOX
The following guide contains the basic necessary information to begin
installing your new Ramsond Solar Panel (hereafter referred to as
“module”). Since there is no way to include every possible application
or method of use, the information provided is of a general nature and is
based on the experience and technical skills of many qualified Ramsond
technicians and product specialists. The following information does not
constitute a warranty, expressed or implied. Ramsond Corporation does
not assume responsibility and expressly disclaims liability for loss,
damages, or expenses arising from or in any way related to installation,
operation, use, or maintenance of PV modules. Ramsond Corporation
assumes no responsibility for any infringement of patents or other rights
of third parties that may result from the use of PV modules. Ramsond
Corporation reserves the right to make changes to the product(s),
specifications or manual at any time without prior notice. All rights
reserved.
Please inspect the unit thoroughly before you begin reading this guide.
You should find the photovoltaic (PV) solar panel in perfect working
order. If you notice any physical damage to the glass-encased Solar
Cells, the rear-mounted Junction Box or the pre-installed Heavy
Duty Cables (100 Watt panels and above only), DO NOT continue to
install the panel or try to perform repairs yourself. Any attempt to do so
is not only dangerous, but it will invalidate the warranty. If your panel
appears to be in working order, please continue reading this manual
completely and ensure all information is understood.
FIND WHICH RAMSOND SOLAR PANEL YOU HAVE BELOW
Different models may have different features out-of-box:
•
5 Watt - 50 Watt panels have cable-ready screws
inside the waterproof Junction Box
•
100 - 180 Watt panels come with heavy duty, 1/4”
thick, insulated cables using a 2.0mm copper core
soldered inside the waterproof Junction Box
•
Pre-wired panels are set up for SERIAL CONNECTION,
described later in this manual. All panels can be set
up for PARALLEL CONNECTION, also described later.
•
All panels can be prepared for use in either SERIAL
or PARALLEL systems
GENERAL SAFETY GUIDELINES
Installation of solar photovoltaic (PV) products should always be performed only by qualified individuals, since they may require specialized skills
and knowledge.The installer should follow all the safety precautions in this guide in addition to any local codes regarding this type of installa-
tion. They should be familiar with both the mechanical and electrical requirements of the system before performing any service, maintenance,
or installation. Keep this guide in a safe place for future reference, care, and maintenance or if the modules are sold or
disposed of.
Do not disconnect any solar module while under load.
Do not attempt to disassemble the modules, remove any components or attached nameplates.
Do not touch any electrical terminal with unprotected hands or skin.
Do not apply paint or adhesive to the top surface of the modules.
Do not use mirrors or magnifiers to artificially concentrate sunlight onto the module's surface.
Do not expose back sheet foils directly to sunlight.
Do not wear metallic rings, watchbands, earrings, nose rings, lip piercings or any other conductive materials
during installation of troubleshooting of photovoltaic systems.
Do not attempt to drill holes through the glass surface of the modules. Doing so will void the warranty.
Do not drill additional mounting holes in the aluminum module frame. This will also void the warranty.
Do not lift the module by the junction box or any attached electric cables.
Do not stand or step on the module.
Do not drop the module or allow objects to fall onto it.
Do not place heavy objects on top of the module; this could cause the glass encasements to break.
Do not throw the module or otherwise set it down forcefully.
Do not transport or install the module inappropriately as it could damage the module.
1