O BVNG & BVLP Series Electric Motor - NG/LP fired READ THIS MANUAL This manual contains important information for the use and safe operation of your RAMTEQ machine. FAILURE TO READ THIS MANUAL AND FOLLOW ITS INSTRUCTIONS PRIOR TO OPERATING OR ATTEMPTING ANY SERVICE OR MAINTENANCE PROCEDURE COULD RESULT IN SERIOUS INJURY OR DEATH TO YOU OR OTHER PERSONS; ALSO DAMAGE TO THE MACHINE OR TO OTHER PROPERTY.
n n n n n n n n n n n n n n INSPECTION Carefully unpack your new RAMTEQ equipment by removing the banding and cardboard box from pallet. Remove the pressure washer from the pallet and check for any physical damages that may have occurred during shipment. Check for all parts specified and shown below.
FAILURE TO READ AND OBSERVE ALL WARNING STATEMENTS COULD RESULT IN SEVERE BODILY INJURY OR DEATH, POSSIBLE INJURY TO OTHER PERSONS, DAMAGE TO MACHINE OR OTHER PROPERTY. n DO NOT operate this machine in areas where open flames are not permitted. DO NOT store or use combustible materials on or near this machine. Use this equipment only in well ventilated areas. Failure to follow this warning may cause carbon monoxide build up, fire or explosion, and possible injury or death.
LOCATION & INSTALLATION GUIDELINES n Locate the machine on a solid and level surface so that engine and pump crankcase oil lubricate components properly. Avoid areas where water can build up in the working area. Possible injury can occur caused by the surface becoming slippery from water build up. n Locate the machine in a well-ventilated area and away from flammable materials or fumes. Be sure ventilation warnings are observed. Keep pressure washer at least 18” away from flamable materials.
STARTING THE MACHINE Following the steps below will insure successful operation: n n n n n n n n n n n n n n Read this manual completely before attempting to start the machine. Check that the Motor/Burner switches are in the "OFF" position Check the pump oil level and fill with SAE 30w non-detergent oil if needed. Connect water hose to pump (or float tank if equipped). Turn on water source. Connect the power cord to a properly grounded power source. Turn the manual gas valve to “ON” position.
FAILURE TO MAINTAIN HEAT EXCHANGER COIL MAY RESULT IN A STEAM EXPLOSION WHICH MAY CAUSE SERIOUS INJURY OR DEATH. EXCHANGER COIL MAINTENANCE n Hard water conditions may eventually cause clogging in the heat exchanger coil if left unattended. Scale deposits will compromise the heating efficiency and produce an unsafe condition over time. It may be necessary to descale coil. n Scale buildup from certain detergents may eventually clog up the heat exchanger coil causing an unsafe condition.
15 14 13 1 Exploded view on page 9 2 12 3 4 5 11 9 10 7 8 6 BV Natural Gas/Liquid Propane Components Ref# Part# Description Qty.
4 3 1 5 2 1a 1b 1c 1d 1e 1f 1g 1h 1i 1j 1k 1m 2 3 4 5 270-00028-01 270-00028-02 270-00028-03 270-00028-04 270-00025-01 270-00025-02 270-00025-03 270-00025-04 270-00028-01 270-00028-02 270-00028-03 270-00028-04 265-00001-01 275-00001-01 552-00002-01 284-00001-01 Nozzle, Water #5.5 0º (BV 500,600) Nozzle, Water #5.5 15º(BV 500,600) Nozzle, Water #5.5 25º(BV 500,600) Nozzle, Water #5.5 40º(BV 500,600) Nozzle, Water #4.0 0º (BV 750) Nozzle, Water #4.0 15º(BV 750) Nozzle, Water #4.
3 4 2 5 1 6 Ref# Part# Description 1 2 3 4 Terminal Strip Time Delay (All Upgrades) Controller Box Honeywell (All Upgrades) Contactor (5hp 1ph 230v; 6hp 1ph 230v; 7.5hp 3ph 230v) Contactor (5hp 3ph 230v; 10hp 3ph 460v) Contactor (5hp 3ph 460v) Contactor (7.5hp 1ph 230v) Contactor (7.5hp 3ph 460v) Contactor (10hp 3P 230v) Overload (5hp 1ph 230v; 6hp 1ph 230v; 10hp 3ph 230v) Overload (5hp 3ph 230v; 10hp 3ph 460v) Overload (5hp 3ph 460v) Overload (7.5hp 1ph 230v) Overload (7.5hp 3ph 230v) Overload (7.
® RAMTEQ n n n n
® RAMTEQ n n n n
2 1 Ref.
® RAMTEQ n n n n
® RAMTEQ n n n n
problem cause action Low Water Pressure Insufficient water source Old or incorrect nozzle Plumbing or hose leak Obstruction in spray nozzle Chemical valve open Unloader valve worn Pump valves dir ty or worn Check hose size/water source Replace nozzle Tighten, repair or replace leak Clean or replace nozzle Close valve or submerge hose Replace unloader Clean or replace packing/valves No Chemical Flow Detergent valve closed Low detergent level Chemical screen dir ty Open detergent valve Fill detergent
RAMTEQ Limited One Year WARRANTY Ramteq Incorporated ("RAMTEQ") warrants that the Product you have purchased from RAMTEQ or from an Authorized RAMTEQ Reseller is free from defects in materials or workmanship under normal use for a period of one (1) year from the date of purchase. This warranty extends only to you, the original Purchaser. It is not transferable to anyone who subsequently purchases the Products from you.
Ramteq Manufacturers Warranty Period Click on pictures to open manufacturers website. 5 years 5 years 3 years 3 years 3 years 3 years 18 months 18/36 months Ramteq Pressure Washers 14275 NORTHWEST FREEWAY HOUSTON, TX 77040 1 year PHONE: 713.983.6000 FAX: 713.983.
