FCC ID:A4C91007A Support www.randmcnally.
Contents What’s in the box.................................................................................................................................................................... 2 Streaming Music................................................................................................................................................13 ClearDryve® Parts..........................................................................................................................................
What’s in the Box ClearDryve® 220: • .ClearDryve® headphone • Audio cable • Charging cable • .Hard-sided carrying case • Detachable earpiece (comes pre-assembled to the headphone) • .Detachable headpad 2 ClearDryve® Parts Microphone Head Band Mic Boom Arm Earpiece Release Fixed Earpiece Detachable Headpad Function Buttons Detachable Earpiece (Dimensions: approx. 8"H x 7"W x 3.
Function Button Layout The mic boom arm, ports, LEDs, and function buttons on the ClearDryve® headphone are on the same earpiece. You can use this earpiece on either ear. ClearDryve® automatically adjusts for either side when you extend the mic arm. To switch the earpiece with controls from one ear to the other, swivel the mic boom up and over to the other side. 1. .Vol + button 1 2. .Vol – button 3. .Micro-USB port 2 4. 3.5mm audio input 3 5. .Multi-function button (MFB) 4 7 6. .
Getting Started with ClearDryve® Power ClearDryve® On and Off To get started using ClearDryve®, first you need to charge the battery. After you power it on, then you can pair ClearDryve® to your Bluetooth® - enabled phone, tablet or laptop. Once ClearDryve® is paired, you can immediately start taking and managing calls or listening to music. To turn ClearDryve® on and off: 1. To power ClearDryve® on, press the MFB. 2. You will hear “Power on.
Once a device is paired, the LED stays solid blue. ClearDryve® will reconnect automatically when Bluetooth® is enabled and the device is within range. To pair ClearDryve® with a BT device: 1. Power on ClearDryve®. 2. Enable Bluetooth® on your device. Leave the device on the Bluetooth Settings screen so it stays in “pairing” mode. ClearDryve® will display on your device as ClearDryve®. Select it. The LED will change to solid blue. 3. 4.
Answer an Incoming Call End a Call Redial the Last Number To answer an incoming call: To end a call: To redial the last connected number: 1. Press the MFB. 1. Press the MFB to hang up. 1. Quickly press the MFB twice. 2. ClearDryve will beep once to confirm. The call will be live immediately. 2. ClearDryve will beep once to confirm. 2. ClearDryve® will beep once to confirm.
Turn the Volume Up and Down Streaming Music At any time, you can press the volume buttons to turn the volume of the call up or down. There are 16 different volume levels available. Quick Access To change the volume: 1. Press Vol + to increase the volume. 2. Press Vol – to decrease the volume. 3. ClearDryve® will beep when you reach the lowest or highest volume settings. Note: Depending on your device, the volume buttons may behave differently.
Turn the Volume Up and Down Go to the Next/Previous Song Connect to a Wired Device At any time, you can press the volume buttons to turn the volume of ClearDryve® up or down. To switch to a different song: You can connect ClearDryve® to any standard 3.5mm audio aux jack. There are 16 different volume settings available. To change the volume: 1. Press Vol + to increase the volume. 2. Press Vol – to decrease the volume. 3. ClearDryve® will beep when you reach the lowest or the highest volume. 1.
Active Noise Cancellation The ClearDryve® signal processing removes more than 90% of noise reaching the microphone so those on the other end of the call hear you — not the background. This digital noise suppression is always active. In addition, your ClearDryve® features Active Noise Cancellation (ANC), which eliminates the need to “crank up the volume” by canceling out ambient noise reaching your ear. The result is a crystal-clear listening experience for you as well. To turn ANC on or off: 1.
Troubleshooting & FAQ Reset to Factory Settings You may need to restore ClearDryve back to its factory state, typically when switching over to newer model smartphones / laptops for daily use. Clearing the “pairing history” on your headphones can help improve connection times between your headphones and new devices. ® To reset ClearDryve®: 1. Make sure ClearDryve® is powered off. Now press and hold MFB to place it in pairing mode. 2. Press and hold Vol - and MFB at the same time until you hear 2 beeps.
Help and Support Warnings, End-User License Agreement, and Warranty IMPORTANT! Before using this Rand McNally product, you should review applicable law regarding the use of this product, as federal, state or local law may prohibit or otherwise restrict the use of this product while operating a motor vehicle. Contact Rand McNally customer support for assistance: • By phone: 1-877-446-4863 • .By email: support@randmcnally.com • .On the web: http://www.randmcnally.
Notes: _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ _________________________
