OPERATOR’S MANUAL This manual provides information on installation, operating, maintenance, trouble shooting & replacement parts for CHICK-FIL-A REFRIGERATED BREADING TABLE 52365WPRM-CFA NOTIFY CARIER OF DAMAGE AT ONCE. It is the responsibility of the consignee to inspect the container upon receipt of same and to determine the possibility of any damage, including concealed damage. Randell suggests that if you are suspicious of damage to make a notation on the delivery receipt.
Table of Contents page 2………………………………….…………Congratulations page 3……………………………………Parts & Service Hotline page 3………………………………...…Serial Number Location page 4-7……………………………….Randell Limited Warranty page 8…………………………………………Unit Specifications page 9……………………………………….........Unit Installation page 10-12....……………………………………...Unit Operation page 13-16……………………………..Preventive Maintenance page 17-18..…………………………………..Electrical Diagram page 19……………………………………..……Troubleshooting page 20-23…………………………….……..
In addition, all Randell food service equipment is backed by some of the best warranties in the food service industry and by our professional staff of service technicians. Retain this manual for future reference. NOTICE: Due to a continuous program of product improvement, Randell reserves the right to make changes in design and specifications without prior notice. NOTICE: Please read the entire manual carefully before installation.
Warranty Policies UNIFIED BRANDS/Randell Chick-Fil-A – Breading Table (Product 52365WPRM-CFA) EXCLUSIVE OPTIONAL 5-YEAR LIMITED WARRANTY INFORMATION (U.S & Canadian Sales only) Randell believes strongly in the products it builds and backs them with the best warranty in the industry. Standard with every unit comes the piece of mind that this unit has been thoroughly engineered, properly tested and manufactured to excruciating tolerances, by a manufacturer with over 30 years of industry presence.
Items Not Covered Under Warranty • Preventative Maintenance type of repairs such as condenser cleaning, temperature adjustments, clogged drains, unit leveling, and gasket replacement (including re-application of silicone), or cleaning. • Repairs caused by neglect to follow recommended PM schedule • Repairs caused by abuse such as freight damage, or scratches and dents.
SANITATION REQUIREMENTS Certain areas require specific annotation requirements other than N.S.F. & U.L. standards. Randell must be advised of these specifications before fabrication of equipment. In these special circumstances, a revised quotation may be required to cover additional costs. Failure to notify Randell before fabrication holds the dealer accountable for all additional charges.
RETURNED GOODS Authorization for return must first be obtained from Randell before returning any merchandise. Any returned goods shipment lacking the return authorization number will be refused, all additional freight costs to be borne by the returning party. Returned equipment must be shipped in original carton, freight prepaid and received in good conditions. Any returned merchandise is subject to a minimum handling charge (consult factory for rate).
Unit Specifications 52365WPRM-CFA Model 52365WPRM-CFA 8 L D H Work Hgt. Doors H.P. Volts Amps NEMA Storage (cubic ft) Ship Wt. 65" 33" 42" 39" 3 1/2 115 12 5-15P 13.
Unit Installation SELECTING A LOCATION FOR YOUR NEW UNIT The following conditions should be considered when selecting a location for your unit: 1. Floor Load: The area on which the unit will rest must be level, free of vibration, and suitably strong enough to support the combined weights of the unit plus the maximum product load weight. All casters must be in contact with the floor to support the weight. Casters may require shims in order for the caster to be in contact with the floor.
NOTE: It is important that a voltage reading be made at the compressor motor electrical connections, while the unit is in operation to verify the correct voltage required by the compressor is being supplied. Low or high voltage can detrimentally affect operation and thereby void its warranty. Unit Operation UNIT INFORMATION Mechanical Compartment 1. The breading station is supplied with a main power switch. The switch is located on the rear of electrical box behind the upper hinged vented door.
Note: All cleaning of rail lift mechanism must be done while lid is in closed position. The tension of the lift mechanism has been pre-set at the factory. MORNING STARTUP OF PREP RAIL 1. Unit cleaning may be performed at this time. 2. Turn on unit. Power switch for rail is found behind upper hinged vented door. 3. Allow a minimum 45 minutes for your unit to cool down before loading product. A uniform frost pattern will appear on side walls and bottom of prep rail area. 4.
Unit Operation - cont. To raise temperature in the refrigerated rail: A. Push and hold the “set” button until 34 appears then release the “set” button. 34 is the current set point temperature. B. Push and release the up arrow 2 times until 36 is displayed. Push and release the “set” button one time. The new set point, 36, will flash 3 times and then will be locked in. To lower temperature in the refrigerated rail: A. Push and hold the “set” button until 34 appears and then release the “set” button.
Preventive Maintenance Randell strongly suggests a preventive maintenance program which would include the following monthly, weekly, and daily procedures: If a failure of the equipment is a direct result of any of the Preventative Maintenance guidelines being neglected, the repairs and parts replacements will not be covered under warranty. It is recommended that the customer contact the local Authorized Service Agent to provide a quote to perform periodic Preventative Maintenance. Daily PM Procedures: 1.
Monthly PM Procedures: 4. Cleaning of all condenser coils on a monthly basis. Condenser coils are a critical component in the life of the compressor and must remain clean to assure proper air flow and heat transfer. Failure to maintain this heat transfer will affect unit performance and eventually destroy the compressor. Clean the condenser coils with coil cleaner and/or a vacuum, cleaner and brush. Proper care of the filter will reduce the need for this task. See item #1. 4A.
8B. Fit o-ring seals back onto valve components. Piece valve together, insert bolts, apply nuts, and tighten (do not over-tighten) NOTE: DO NOT USE SHARP UTENSILS FOR ANY OF THE ABOVE PROCEDURES.
STEPS FOR REMOVING THE GREASE FILTER FOR CLEANING: Step 1: Locate grease filter on the front of the condenser air in duct. Behind lower hinged vented door. Step 2: Locate finger hole opening to remove filter without the use of tools. Step 3: Insert finger and force filter upwards. Step 4: Filter should fall out in your hands. Step 5: Pull downwards to release the filter at the top. Step 6: Filter should fall out of the top holding bracket.
Electrical Diagram Prior to September 2008 unifiedbrands.
Electrical Diagram – cont.
Trouble Shooting Guide SYMPTOM POSSIBLE CAUSE PROCEDURE Unit doesn't run 1. 2. 3. 4. 5. 6. 7. 8. No power to unit Temperature control turned off Temperature control faulty Compressor overheated Condenser fan faulty Overload protector faulty Compressor relay faulty Compressor faulty 1. 2. 3. 4. 5. 6. 7. 8. Unit short cycles 1. 2. 3. 4. 5. Condenser coil/filter dirty Pressure control settings Condenser fan faulty Compressor faulty Overload repeatedly tripping 1. Clean coil/filter 2.
Replacement Parts Refrigerated Breading Tables CAUTION: Hold lid with both hands securely at all times during opening and closing.
unifiedbrands.
ITEM DESCRIPTION PART # 1 Hinged Cover with Recessed Handle RP CVR0701 2 Counter Balance Hinge Lift Assy HD HNG0501 3 Adapter Grid, 12” x 20” RP ADP0801 4 Drain Screen, 2” RP DSN002 5 Elbow, 1 ½” PVC Fem x Glue PB ELB9905 6 Pipe, 1 ½” PVC PB PIP150 7 Ball Valve, 1 ½” PVC Female PB VLV9901 7A Pull Gate Valve 1 ½” PVC Female (after August 2009) PB VLV0901 7B Drain Elbow extension downspout RP ELB0903 Dixell Digital Control for Base RP CNT0204 Dixell Probes for Base RF CNT0505
15 Shelf, 13-1/8” x 25-1/4” Stainless Steel HD SHL015SS 16 Door Hinge Top/Bottom HD HNG0706 16A Door Hinge Self Closure Spring (Bottom Only) HD HNG0707 17 Toe Style Bracket/Door Handle, Stainless Steel RP HDL0501 18 Door Gasket IN GSK1020 19 Evaporator Fan Motor, 120V w/blade EL MTR2338 20 Temperature Control Probe - Dixell RF CNT0505 21 Evaporator Condensate Pan, Plastic RP DRP107 22 Expansion Valve – Rail RF VLV404 22A Expansion Valve – Base RF VLV414 23 Shield Panel for Bas
