4652 +30 MIC +60 LINE OL Important Safety Instructions CP 52 Manual CP 52 Data Sheet Rane Professional Install Products Sound System Interconnection Schematics Warranty Declaration of Conformity ACTIVE DETECT THRESHOLD CONTENTS (in order of appearance) INPUT TRIM 2 0 4 10 6 LEVEL 8 PAGING +16 2 0 4 10 6 8 2 0 4 10 6 LINE 2 8 2 0 4 10 6 LINE 3 8 2 0 4 10 6 PRIORITY PROGRAM INPUT LEVELS LINE 1 8 OFF ON DUCKER DEPTH L1 L2 L3 P PROGRAM SELECT RMT SIG OL 2 0 4 10
IMPORTANT SAFETY INSTRUCTIONS For the continued safety of yourself and others we recommend that you read the following safety and installation instructions. Keep this document in a safe location for future reference. Please heed all warnings and follow all instructions. Do not use this equipment in a location where it might become wet. Clean only with a damp cloth. This equipment may be installed in an industry standard equipment rack.
OPERATORS MANUAL CP 52 COMMERCIAL PROCESSOR PAGING INPUT TRIM +30 MIC DETECT THRESHOLD LEVEL 4 6 0 10 2 +60 LINE OL ACTIVE PROGRAM INPUT LEVELS LIMIT THRESHOLD +8 8 –3 +16 –20 +20 LINE 1 LINE 2 LINE 3 4 6 4 6 4 6 0 10 0 10 0 10 2 8 2 8 2 ZONE PRIORITY 8 4 6 0 10 2 DUCKER DEPTH L1 8 LIMIT PROGRAM SELECT OFF L2 L3 P LEVEL 4 6 0 10 2 ON RMT SIG OL LIMIT THRESHOLD +8 8 –3 +16 40 100 250 630 1.
Front Panel Description 1 3 6 INPUT TRIM DETECT THRESHOLD 3 9 11 PAGING +30 MIC 6 0 10 2 +60 LINE 2 LEVEL 4 OL ACTIVE 4 5 PROGRAM INPUT LEVELS LIMIT THRESHOLD +8 8 13 14 –3 +16 –20 +20 LINE 1 LINE 2 LINE 3 4 6 4 6 4 6 0 10 0 10 0 10 2 8 2 8 2 ZONE PRIORITY 8 4 6 0 10 2 DUCKER DEPTH PROGRAM SELECT L1 8 OFF L2 L3 LEVEL P RMT SIG OL 8 10 6 0 10 2 ON LIMIT 4 LIMIT THRESHOLD +8 8 –3 +16 –20 +20 LIMIT 40 100 250 630 1.
Rear Panel Description ZONE REMOTE ZONE OUTPUT RIGHT POWER D1 D0 MIN + EXPAND OUTPUT LEFT – – + LEVEL MONO + 5 1 2 PAGE D1 D0 Vc Vr 3 + – – 4 + + 5 20 SEC PROGRAM OFF ON – 6 7 8 L DETECT THRESHOLD – ZONE 750mA CLASS 2 EQUIPMENT PAGING INPUT RELEASE TIME 9 10 11 L R PRIORITY PAGE LEVEL TRACKS ZONE LEVEL R L3 L2 PROGRAM INPUTS 12 OFF ON L1 LOW / HIGH CUT FILTER OUT IN 100 Hz / 7 kHz 13 14 MIC PHANTOM POWER OFF CP 52 INPUT + – + – MADE IN U.S.A.
The CP 52 supports a wired remote for Zone Level and Zone Source selection. Wire lengths of up to 1000 feet (300 meters) are possible. A brief list of suitable wire types is provided here in the Wire Types section. The ZR 1 remote provides Zone Level and Source Selection, allowing local control from inside the Zone. If only one of the two controls is used, you may wish to remove the unused knob and cover the hole with one of the plugs provided in the kit.
Recommended Calibration Procedure The CP 52 is a very versatile instrument. While this allows it to conform to the requirements of a large number of system applications, it also results in complexity. For this reason, it is very important to use an organized approach to system calibration. Once the system is connected and the internal switches set for your specific application, it is important to take the time for proper calibration.
CALIBRATION 1. Connect the power supply and verify the POWER indicator lights. 2. Verify the Zone LEVEL control is set to maximum and that an active source is playing for each of the Program Inputs intended for use. Select each Program Input and adjust its Input Level control to be the very loudest you would ever desire. 3. Adjust the Zone LIMIT THRESHOLD so that it just starts to audibly reduce the output level. This ensures that the level will never be louder than the maximum level just set. 4.