user manual

Data Sheet-8
CP 64S
COMMERCIAL PROCESSOR
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 USA TEL [phone] FAX [phone] WEB www.rane.com
CP 64S
COMMERCIAL PROCESSOR
Rear Panel
All features & specications subject to change without notice. DOC 102906
Architectural Specifications
e processor shall provide two fully independent gated paging
inputs, three line-level non-priority program inputs and one
gated line-level priority program input. Two zone outputs shall
be served. Zone 1 shall be a stereo zone with balanced, cross-
coupled outputs. Zone 2 shall be a mono zone with a balanced
cross-coupled output. Mono expansion ports for page, program
or zone signals shall be provided for each zone. Wired remote
control ports shall be provided for paging zone assign, zone
program select and zone level.
Page inputs shall use a 5-pin Euroblock connector. Paging
controls shall include:
• 30 dB mic/line input pad.
• Input gain trim range of 30 dB to 60 dB.
• Mic gate threshold (range -∞ to +4 dBu).
• 15 volt phantom power (internal switch).
• Paging priority (page 1, none, page 2; internal switch).
• Pre- or post-zone level summing (internal switch).
• Front panel paging zone assign (Remote, Z1, Z2, Both).
• Remote paging zone assign (O, Z1, Z2, Both).
• Paging zone level.
Each Program input shall have stereo RCA input jacks and
independent input level control. e priority program assign
switch shall provide priority program override to zone 1, zone 2,
both, or neither (o). e gated priority program input shall
have internally adjustable threshold and release time controls.
Zone outputs shall use 3-pin Euroblock connectors. Zone
controls shall include:
• Ducker on/o
• Ducker depth (-6 to -50 dB)
• Program select (L1, L2, L3, P)
• Zone level
• 7-band graphic equalizer (±12 dB)
• Servo-Locked-Limiter
™
threshold (-20 to +20 dBu)
• Mono switch for Zone 1 (internal)
• Remote engage switch
Wired remote ports shall use 3-pin Euroblock connectors.
Remote logic shall be active low with internal pull-up. Remote
level control shall be ratiometric DC control with 5 volt
reference.
e unit shall be capable of operation by means of its own
built-in universal power supply operating at 100-240 VAC and
meet CE requirements. e unit shall be UL and cUL listed. e
unit shall be entirely constructed from cold-rolled steel.
Reliability and efficiency are to be primary design consider-
ations.
e unit shall be a Rane Corporation CP 64S Commercial
Processor.
Available Accessories
• SCP 2S Security Cover (for EQ section)
• SC 1.7 Security Cover (for entire front panel)
• PR 2 Page Assign Remote Control
• ZR 1 Zone Source/Volume Remote Control
• Hole Plugs (6 Provided with SCP 2S)
PRIORITY
ASSIGN
ZONE
ZONE
1
PAGE
+30 +60
1&2
PRIORITY 321
RANE CORP. MADE IN U.S.A.
OL
Z2 Z1
Z1 Z2
+
–+ –
+
–
+
–
D1 D0 Vr Vc
Vr Vc
1
2
DETECT THRESHOLD
REMOTE PAGE
ZONE ASSIGN WIRING
PAGE 2PAGE 1
LIMITERWIRING
ZONE 1 ZONE 2
PAGE
1
TRIM
PAGE
2
TRIM
CP 64S
+8
+8
PAGING INPUTS
R
L
R
L
+30 +60
MIC LINE
–20 +20–20 +20
REMOTES OUTPUTS
MIN MAX
PROGRAM INPUTS
ZONE 2
EXPAND OUT
ZONE 1
EXPAND OUT
ZONE
2
Z2
PGM
Z2 EXPAND Z2 MONO REMOTE 1 INPUT 1
REMOTE 2 INPUT 2Z1 RIGHT Z1 EXPAND Z1 LEFT
Z2 LEVEL
Z1 PGM Z1 LEVEL
ACN 001 345 482
MIC LINE
100-240 V
50/60 Hz 12 WATTS
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
PGM PGM
PAGE
THIS DEVICE COMPLIES WITH
PA RT 15 OF THE FCC RULES FOR
A CLASS 'B' COMPUTING DEVICE.
off
Euroblocks are included, removed here for label visibility.