OWNER’S MANUAL RANE SIXTY-TWO MIXER MANUAL SIXTY-TWO
OWNER’S MANUAL Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
OWNER’S MANUAL Instructions de Sécurité 1. Lisez ces instructions. 2. Gardez précieusement ces instructions. 3. Respectez les avertissements. 4. Suivez toutes les instructions. 5. Ne pas utiliser près d’une source d’eau. 6. Ne nettoyer qu’avec un chiffon doux. 7. N’obstruer aucune évacuation d’air. Effectuez l’installation en suivant les instructions du fabricant. 8. Ne pas disposer près d’une source de chaleur, c-à-d tout appareil produisant de la chaleur sans exception. 9.
OWNER’S MANUAL Copyright Notices ©2014 Rane Corporation. All rights reserved. Serato DJ and Scratch Live are trademarks of Serato. Trademarked in the United States and other countries. This software is based in part on the work of the Independent JPEG Group, and uses libpng code, copyright © 2000-2002 Glenn Randers-Pehrson. The Serato NoiseMap™ Control Tone, the audio pressed on Serato Control vinyl and Control CDs, is copyright ©2004-2014 Serato.
OWNER’S MANUAL Contents 2 Important Safety Instructions 4 Check List 6 Quick Start: Software 6 6 6 6 Serato DJ Software Installation for Mac OSX Serato DJ Software Installation for Windows Serato Scratch Live Other DJ and DAW Programs 7 Quick Start: Hardware 7 Analog Inputs 8 Analog Outputs 8 Quick Start: Operation 8 USB Control Source 10 Sixty-Two Overview 11 Sixty-Two Connections 13 Deck Input Channels 13 13 13 13 14 14 14 14 14 15 Source Selector Level Pan Tone Controls Filter FlexFX Channel Fader
OWNER’S MANUAL Quick Start: Software Before using your mixer, at least read this short section for the basics. Read the complete manual to get the best investment from your new Sixty-Two. This section will help get you started with one computer. Serato DJ Software Installation for Mac OSX Before installing, we recommend you check for a newer version of Serato DJ at serato.com/downloads and install the latest Serato DJ version if it is newer than the version on the CD-ROM that comes with your mixer. 1.
OWNER’S MANUAL POWERED POWERED MAIN SPEAKERS OR AMPS MAIN OUT RIGHT BOOTH OUT SIXTY-TWO SESSION OUT LEFT RIGHT ANALOG INPUTS IN PHONO GROUNDS LEFT MADE IN U.S.A. RANE CORP. 100-240V INPUT SELECT 50/60 Hz 15 WATTS PH - CD USB B USB A FLEXFX LOOP RETURN SEND RIGHT LEFT RIGHT 4 PH - CD 3 PH - CD 2 PH - CD 1 MIC INPUT LEFT MIC - LINE CD OR TURNTABLE OUT CD OR TURNTABLE OUT USB 7.
OWNER’S MANUAL Analog Outputs • Main Out is on a pair of balanced XLR jacks with pin 2 “hot” per AES standards. • Booth Out is on a pair of balanced ¼˝ TRS (tip-ring-sleeve) jacks. • Session Out is available on a pair of unbalanced RCA jacks. • Headphones output mix is available on both ¼˝ and 3.5 mm jacks. The Main, Booth and Session outputs arrive from the same “Main Mix” signal. Main, Booth and Session outputs each have their own LEVEL control.
OWNER’S MANUAL How To Calibrate Serato DJ With music playing in the background through your system or booth output, put your needle on the record with the turntable stopped. If you are using CD players, the same rules apply. Have the CD deck paused or stopped while calibrating. Click and hold the estimate button until the slider stops moving. Moving the Noise Sensitivity slider to the left will make Serato DJ more sensitive to slow record movement, but also more sensitive to background noise.
OWNER’S MANUAL Sixty-Two Overview Software controls are built-in for one or two computers • Includes Serato DJ software. • Includes Rane ASIO and Core Audio Drivers for Serato DJ and other audio programs. • Advanced MIDI and audio routing: route either deck to either USB Port, and MIDI follows the audio. • Independently control Library, Cues, Loops and Samples on two computers with more than 40 software controls. • Each of the two USB ports supports six stereo record and four stereo playback channels.
OWNER’S MANUAL Sixty-Two Connections Power Supply This mixer features an internal universal switching power supply that operates on any AC mains 100 to 240 VAC, 50 or 60 Hz (most places in the world). The universal supply is a major plus for the traveling DJ, who only needs the right IEC line cord, available from a local electronics store. Though this mixer has turn on/off muting, it’s smart to leave the power unplugged until everything else is connected.
OWNER’S MANUAL Two USB Ports There are six stereo record channels and four stereo playback channels. These channels are simultaneously available on two USB ports, allowing two computers to share the device. This allows two DJs to play together and supports uninterrupted transitions from one DJ to another. Rane ASIO and Core Audio drivers allow the Sixty-Two to act as a 12-record 8-playback USB sound card for use with Serato DJ and other third-party software applications that support ASIO or Core Audio.
OWNER’S MANUAL Deck Input Channels Two input channels, or buses, have nearly identical controls with the exception of the Source selectors. Source Selector DECK 1 MIC DECK 1 DECK 2 PH / CD PH / CD The SOURCE selector for Deck 1 selects oneBYPASS of four CLEAN FEED 1 2 3 4 4 6 4 6 B B A A sources: 2 8 2 8 • A Left Virtual Deck (USB stereo playback SP-6 ASSIGN ON pairOVER 4 6 0 10 0 10 1-2) from USB A.
OWNER’S MANUAL DECK 1 MIC DECK 1 DECK 2 MIX DECK 2 PH / CD PH / CD Filter BYPASS CLEAN FEED 1 2 3 4 4 6 4 6 4 6 B B A A The FILTER sweeps from Low-Pass to High-Pass. Set it to 12 o’clock for a flat “no-filter” response. Moving 2 8 2 8 2 8 SP-6 ASSIGN ON LOW position OVER ASSIGN the filter toward the progressively reduces high frequencies. Moving the filter towardSP-6 the HIGH 4 6 0 10 0 10 0 10 LEVELThe Resonance LEVEL MAIN be adjusted on SOURCE SOURCE position progressively reduces low frequencies.
INSERT SYNC OFF ROLL OWNER’S MANUAL OUT FILTER BPM NUDGE S SLIP SAVE LOOP TIME BEAT SHIFT Aux This digital input is on USB playback stereo pair 5-6 and is normally used for the Serato DJ SP-6 Sample Player. To enable the SP-6, go to Setup > Expansion Packs > SP-6 Sample Player and check the box for “Enable SP-6 Sample Player.” To assign the SP-6 Sample Player to AUX, click the SP-6 tab at the top of the main software screen and select SP-6 Output as “A.
OWNER’S MANUAL MIC DECK 1 1 MIC DECK Software Controls DECK 1 1 DECK DECK 2 2 DECK PH /PH CD/ CD BYPASS FEED BYPASS CLEAN CLEAN FEED SP-6 ASSIGN SP-6 ASSIGN BACK BACK LOAD LOAD SCROLL SCROLL LOOPS LOOPS AUTO AUTO MANUAL MANUAL BEATS BEATS SELECT SELECT SYNC SYNC LOOP LOOP IN IN SYNC OFFOFF SYNC ROLL ROLL OUTOUT SLIP SLIP LOOP LOOP SAVE SAVE SHIFT SHIFT MIXMIX DECK 2 2 DECK PH /PH CD/ CD 1 12 2 3 34 4 4 4 6 6 4 4 6 6 4 B has B B A A controls B A The Sixty-Two AMixer dedicated Serato
BEATS SELECT LEFT SCROLL SYNC LOOP AUTO OFF OFF FLEXFX +6 HIGH OFF LOOPS OWNER’S MANUAL RIGHT FLEXFX PAN IN INSERT MANUAL SYNC OFF ROLL OUT BEATS SELECT OFF LOW BPM HIGH LOW +6 OFF +6 OFF HIGH LOW +6 +6 2 LEFT RIGHT 0 10 FILTERLOW FILTER FLANGER HIGH +6 OFF PHASER MID ECHOMID +6 ROBOTLOW REVERB HIGH FILTER SLIP START / STOP FLANGER +Fb BPM:120 * 1:1 4000 ms SCROLL SYNC 8 0 10 4 4 6 6 EXT.
OWNER’S MANUAL FlexFX Loop The FlexFX Bus in the Sixty-Two works differently than a typical effects insert loop. This architecture opens up many new possibilities not possible with simple effect insert designs found on other mixers. The FlexFX Bus is more like an auxiliary bus that can have multiple signals assigned to it. Signals assigned to the bus may then have internal effects, external analog effects and external USB effects applied in any combination.
BYPASS SP-6 ASSIGN OWNER’S MANUALBACK LOAD ON 4 CLEAN FEED 6 6 2 4 8 0 SOURCE 8 LEVEL 4 B OVER 2 0 1 2 A LEVEL 6 2 10 3 4 A 0 LEVEL 4 B 8 6 2 10 8 0 SOURCE MAIN 4 10 6 2 LEFT SCROLL PAN RIGHT OFF HIGH +6 OFF HIGH +6 LEFT PAN RIGHT BACK 8 0 10 4 6 The six built-in effectsSYNC are: LOOP IN • FILTER • FLANGER • PHASER • HOLD ECHO SYNC OFF ROLL OUT • ROBOT • REVERB OFF FLEXFX LOW +6 OFF LOW FLEXFX +6 0 SCROLL LOOPS MANUAL AUTO SELECT BEATS
OWNER’S MANUAL Effects Display, BPM Source and Match Indicator The effects display shows the name of the effect name current effect, BPM, MIDI Beat-Clock source, Beat Multiplier and Time. A bar graph represents BPM *, S, A, B PHASER the effect time relative to its range. If no effect is selected, the information for the last effect is BPM:120 * 4:1 displayed. The display for the Robot and Reverb is 2000 ms time multiplier somewhat different.
OWNER’S MANUAL Effects Parameter Table Effect Depth Knob Filter DEPTH adjusts the strength of the effect. Flanger Phaser Echo DEPTH adjusts the amount of echo recirculation, which in turn affects how quickly the echo effect decays. The amount of recirculation varies with the echo options selected (see last column). Setting the control to minimum or “0” results in a Dry signal with the minimum recirculation setting.
OWNER’S MANUAL Shift Options Several menus are available on the mixer to set preferences. Available menus are indicated with a gray up arrow. To select a menu, press and hold the SHIFT button and then press the desired menu key. Note: the Shift button may be labeled as the Delete button on older Sixty-Two Mixers. Ext. Insert Options Menu This menu sets the sensitivity of the external SHIFT EXTERNAL INSERT analog insert to +4 dBu or -10 dBV.
OWNER’S MANUAL Deck 1-2 Channel Options Menu A menu is available for each deck input channel. SHIFT … REC PH/CD-1 Press and hold the SHIFT button then press the REC PH/CD-2 CUE button of an input channel. This menu allows FILTER RESONANCE you to select 1 of 2 USB record sources and set CUE the resonance of the Filter. Record options are: • Pre-selector PH/CD 1 input source (required for DVS). • Pre-selector PH/CD 2 input source.
OWNER’S MANUAL Mixer Shift Functions In addition to the menu selections, the Shift button also accesses alternate functions for other buttons. MIDI Start/Stop Hold the SHIFT button and press TAP to toggle MIDI Start/Stop messages. MIDI Start is a system real time message instructing devices to start playing a sequence. MIDI Stop tells devices to stop playing the sequence. START / STOP SHIFT TAP Nudge Hold the SHIFT button and use the BEAT joystick to “Nudge” the outgoing MIDI beat clock BPM up or down.
OWNER’S MANUAL DJ Changeover The Sixty-Two allows two computers running Serato DJ to connect to the mixer simultaneously. This allows two DJs to play at the same time and for easy DJ set changeover. Connect both computers to the two USB ports on the Sixty-Two. For each channel on the mixer, set the DECK SOURCE to either A or B depending on which your computer is connected to. NOTE: If a channel is in use by a computer already, the second computer’s Virtual Deck will become black and display IN USE.
OWNER’S MANUAL Rane Drivers The Serato DJ installer includes Core Audio (Mac) and ASIO (PC) drivers that allow your Rane Sixty-Two to use other popular DJ and DAW audio applications. Once installed, you will have the option to select the Sixty-Two’s inputs and outputs in the audio settings of these programs. ASIO (Windows) The Sixty-Two comes with a low-latency ASIO device driver on the installation CD to interface with Serato DJ and other 3rd-party software applications on Windows operating systems.
OWNER’S MANUAL Deck Inputs 1-2 Page Controls There is one panel for each channel strip on the mixer. Each Deck panel controls these functions: • Analog Input Source: The analog input for each channel may be set for Line level (CD) or Phono level (PH) using a switch on the rear of the mixer. PH/CD 1 and PH/CD 2 are associated with Deck 1. PH/CD 3 and PH/CD 4 are associated with Deck 2. The control panel shows the input mode selected on the mixer for each of the four inputs.
OWNER’S MANUAL The Echo panel allows users to select one of four echo modes: • Echo with no feedback filter and adjustable recirculation 0 to 70%. • Duck Echo: Feedback filter adjustable from 20 Hz to 10 kHz. Recirculation is adjustable 0-70%. • Low-Cut Echo with adjustable feedback filter and adjustable recirculation 0 to 70%. • Low-Cut Hold Echo with adjustable feedback filter and adjustable recirculation of 0% to 100%. • The sliders in the control panel set the low-cut filter cut off frequency.
OWNER’S MANUAL MIDI Mapping When using Serato DJ or Scratch Live software, the mixer is plug-and-play with all required MIDI mapping done for you. For advanced users or with third-party DAWs, it is possible to custom MIDI-map most mixer controls on the Sixty-Two and control the lighting and color of buttons in the Serato DJ control strips. There are three groups of MIDI controls: • Those associated with Deck 1 and the left-hand control strip. • Those associated with Deck 2 and the right-hand control strip.
OWNER’S MANUAL NOTE: The Serato DJ controls on the mixer’s control strips are not mappable in Layer 1 because they are reserved for the default Serato DJ functions. These controls are fully mappable in Serato DJ on all other MIDI Layers. All controls on all layers are mappable in third-party applications that support MIDI Mapping.
OWNER’S MANUAL 112 113 114 115 21 24 27 30 22 23 41 25 40 39 55 42 43 46 33 38 48 SIXTY-TWO 31 49 26
OWNER’S MANUAL MIDI Implementation Serato DJ MIDI Control only supports: • Note On/Off • Standard 7-bit CC (Control Change) MIDI Note ON/OFF Chart The note number for an LED indicator under a button is the same as for the button.
OWNER’S MANUAL 31 0x1F USB Insert Not Permitted Mixer Control 34 0x22 Mic FlexFX Not Permitted Mixer Control 41 0x29 Mic ON Not Permitted Mixer Control 42 0x2A LH SP-6 Assign Not Permitted Mixer Control 43 0x2B LH Back PRI – Green 44 0x2C LH Scroll Encoder Push Not Applicable DAW MIDI Control 45 0x2D LH Manual/Auto Loop Not Permitted Mixer Control DAW MIDI Control 46 0x2E Mic Talk-over Not Permitted Mixer Control 50 0x32 SR Manual/Auto Loop Not Permitted Mixer Co
OWNER’S MANUAL MIDI Control Change Chart Functions highlighted in red are MIDI-Out Mixer controls. Functions highlighted in blue are MIDI-In mixer controls. Functions highlighted in green are MIDI-Out Serato DJ or 3rd-party DAW controls.
OWNER’S MANUAL 40 0x28 FX Echo Type 0-31 32-63 64-95 96-127 0x00-0x1F 0x20-0x3F 0x40-0x5F 0x60-0x7F Echo High-Pass Echo Duck Echo HP Hold Echo 41 0x29 FX Filter Type 0-31, 32-63, 64-95, 96-127 0x00-0x1F 0x20-0x3F 0x40-0x5F 0x60-0x7F Low-Pass Sync Low Low-Pass Sync High High-Pass Sync Low High-Pass Sync High 42 0x2A Echo HP Frequency 0-127 0x00-0x7F 20 Hz-10 kHz, Uniform Octave Steps 43 0x2B Hold Echo HP Frequency 0-127 0x00-0x7F 20 Hz-10 kHz, Uniform Octave Steps 44 0x2C LH Auto Lo
OWNER’S MANUAL Magnetic Fader Maintenance The faders and crossfader in the Sixty-Two are designed with materials highly resistant to corrosion and most chemicals. While they will handle millions of operations, they may become dirty over time. Bad things may be spilled into a fader, but in many instances the fader may not be damaged and the sound quality thus unaffected. Cleaning is only required to maintain the feel of the fader.
OWNER’S MANUAL Sensors Fader Calibration After cleaning or replacement, the sensors may get moved, affecting the contour. After any fader service, perform this procedure to re-calibrate the faders and crossfader. 1.Power off the Sixty-Two. 2. Move all faders to the center-most position. 3. Push down both DECK 1 CUE and DECK 2 CUE buttons at the same time. 4. While holding these buttons down, power on the Sixty-Two. 5.
OWNER’S MANUAL Technical Specifications Sixty-Two Specifications All specifications typical unless otherwise stated Analog Inputs 4 Stereo unbalanced RCA jacks …...Phono or Line level input Rear panel switches for each input …...Phono Response RIAA ±1 dB, Gain: 31 dB at 1 kHz …...Max Phono Input 126 mV …...
OWNER’S MANUAL Battle Bridge Accessory When installing a Sixty-Two mixer in a coffin case, it is important to leave 10 centimeters (3.9 inches) in front and in back of the mixer to allow room for cables and access to controls. The rubber feet provided on the chassis for table top use should remain in place when installing the mixer in a coffin case. When in operation, the coffin case must provide 1 centimeter (0.39 inches) clearance on each side of the mixer and above the controls on the face of the mixer.
OWNER’S MANUAL Limited Warranties Factory Authorized Service Your unit may someday need to be serviced by the Rane Factory if you live in the USA. International customers should contact your dealer or distributor for service. You must call the Rane factory before shipping. Please do not return your unit to Rane without prior authorization. To obtain service or a Return Authorization in the USA, please phone Rane Corporation at 425-355-6000, or fax Rane at 425-347-7757. Limited U.S.A.
OWNER’S MANUAL Warranty Procedure - Valid in U.S.A. only NOTICE! You must complete and return the warranty card or register your product online to extend the Warranty from 2 years to 3 years! TO VALIDATE YOUR EXTENDED WARRANTY: Use the postcard that came in the box with your unit, or go to the support page at dj.rane.com and click on product registration. Fill out the warranty completely, being sure to include the model and serial number of the unit since this is how warranties are tracked.
OWNER’S MANUAL Declaration of Conformity Standard(s) to which conformity is declared: Application of Council Directives: 2002/96/EC 2001/95/EC 2006/95/EC 2004/108/EC 2011/65/EU EN60065: 2002/A1:2006/A11:2008/A2:2010/A12:2011 EN55103-1:2009 EN55103-2:2009 EN50581:2012 ENVIRONMENT E2 SERIAL NUMBERS 850000 - 950000 CE MARK FIRST AFFIXED IN: 2012 Manufacturer: Rane Corporation 10802 47th Avenue West Mukilteo WA 98275-5000 USA This equipment has been tested and found to be in compliance with all applicable
OWNER’S MANUAL SIXTY-TWO 43
OWNER’S MANUAL SIXTY-TWO 44 PART 22489
