Owner`s manual
OWNER’S MANUAL
11
SIXTY-TWO
Sixty-Two Connections
Power Supply
This mixer features an internal universal switching power supply that operates on any AC mains 100 to
240 VAC, 50 or 60 Hz (most places in the world). The universal supply is a major plus for the traveling DJ,
who only needs the right IEC line cord, available from a local electronics store. Though this mixer has turn
on/off muting, it’s smart to leave the power unplugged until everything else is connected.
Analog Inputs
Four Phono / CD inputs are provided by RCA jacks. These may be set for PH or CD using rear panel slide
switches. Analog inputs 1 and 2 are used by DECK 1. Analog inputs 3 and 4 are used by DECK 2. Analog
Input 1 or 2 may be selected in Serato DJ software as the Digital Vinyl Simulation (DVS) signal for the Left
Virtual Deck or for recording on USB stereo pair 5-6. Analog Input 3 or 4 may be selected in software as
the DVS signal for the Right Virtual Deck or for recording on USB stereo pair 7-8. Set any unused inputs to
CD. Connect your turntable ground wires to the PHONO GROUND posts on the rear when using PH inputs.
One stereo Session Input is available on a pair of RCA input jacks. This input may connect two mixers
together or as a general purpose auxiliary input to the mixer.
The Mic Input will accept an XLR 3-pin plug, a balanced ¼˝ TRS (tip-ring-sleeve) plug or an unbalanced
TS (tip-sleeve) plug. This input may be set for Microphone or Line level using the MIC - LINE switch on the
rear panel. Set this to Line when connecting a wireless receiver.
A stereo FlexFX Loop Return input is on unbalanced ¼˝ TS (tip-sleeve) jacks. These inputs automatically
switch to mono when only one cable is connected to the left or right Return input. The FlexFX Return input
is normally used along with the FlexFX Send output to connect an outboard analog effects processor.
Phono Sensitivity and Analog Insert level can be adjusted in the "Rane Drivers" on page 26.
Analog Outputs
There are ve stereo analog outputs available on the mixer:
• MAIN OUT is on a pair of balanced XLR jacks with pin 2 “hot” per AES standards.
• BOOTH OUT is on a pair of balanced ¼˝ TRS jacks.
• SESSION OUT is available on a pair of unbalanced RCA jacks.
• FLEXFX LOOP SEND output is available on a pair of unbalanced ¼˝ inch TS jacks. For a mono FlexFX Send,
use the Left output. The FlexFX Send output is normally used along with the FLEXFX LOOP RETURN input to
connect outboard effects.
• HEADPHONES output is available on both ¼˝ TRS and 3.5 mm jacks.
The Main, Booth and Session outputs arrive from the same “Main Mix” signal. Main, Booth and Session
outputs each have their own LEVEL control. Because all signals are identical, users may use any of these
outputs as the “Main” output if a different cable type is required for system connection.
Rane recommends balanced wiring for the strongest signal and rejection of hum and noise. If your
cable to the destination is less than 10 feet (3 meters), you can often get away with an unbalanced cable.
See the RaneNote “Sound System Interconnection” at rane.com for cable wiring recommendations.
MAIN OUT
SEND
PHONO
GROUNDS
INPUT SELECT
SESSION
ANALOG INPUTS
100-240V 50/60 Hz 15 WATTS
LEFT
RIGHT
MADE IN U.S.A. RANE CORP.
RETURN
FLEXFX LOOP
USB A
USB B
BOOTH OUT
LEFT
RIGHT
LEFT
RIGHT
LEFT
RIGHT
OUT
IN
2
1
4
3
PH - CD
PH - CD
PH - CD
PH - CD
SIXTY-TWO
MIC - LINE
MIC
INPUT