RANE] ZONETECH User Guide (English)
Table of Contents Introduction................................................................................................................................. 3 Box Contents ......................................................................................................................... 3 Support .................................................................................................................................. 3 Setup...................................................................
Introduction Thank you for purchasing the Zonetech. At Rane, performance and reliability mean as much to us as they do to you. That’s why we design our equipment with only one thing in mind—to make your performance the best it can be. Box Contents Zonetech (1) 6-pin 3.8 mm Euroblock inputs (green, for audio inputs) (3) 6-pin 3.8 mm Euroblock outputs (orange, for zone outputs) (1) 3-pin 3.8 mm Euroblock outputs (orange, for zone outputs) (1) 3-pin 3.
Setup Items not listed under Introduction > Box Contents are sold separately. 1. Use the included Euroblock connectors or stereo RCA cables to connect the inputs on the rear panel to your audio sources. 2. Use the included Euroblock connectors to connect the outputs on the rear panel to your zone amplifiers or powered loudspeakers. 3. Use shielded Cat5e or Cat6 RJ45 cables to connect optional remotes or paging devices (e.g.
Features Front Panel 9 7 1 6 5 4 3 10 8 2 1. Display: This display shows information about Zonetech’s current status and options. 2. Power Light: This light is on when Zonetech is powered on. 3. Computer Link Light: This light is on when the Computer Ethernet port on the rear panel is connected to a computer (powered on). You can then use the computer to control Zonetech remotely using a web-based interface. 4.
Rear Panel 4 2 1 10 9 8 7 6 3 5 3 3 3 5 5 5 1. Power Input (IEC): Use a standard IEC cable to connect this input to a power outlet. 2. Bluetooth Antenna Connector (SMA): Connect the included Bluetooth antenna here. Important: For compliance, you must use the included antenna only. No substitutions or modifications to the antenna are permitted. 3. Inputs (stereo RCA): Connect audio sources to these stereo input pairs. 4.
Operation Editing Input Settings You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the settings of each input. To select an input to edit, press the corresponding Input button (1–6) or the Stream button. The display will indicate which input is selected: Input 1–6 or Stream. To show the previous or next setting for the selected input, use the Left/Right (/) buttons (respectively). Turn the Info knob to adjust the value of each setting.
PEQ Frequency (PEQ Freq) PEQ Bandwidth (PEQ Band) This is the center frequency of the midrange parametric equalization band: 40 Hz – 16 kHz (default: 630 Hz). This is the width of the mid-range parametric equalization band: 0.300– 4.000 oct (octaves) (default: 0.500 oct). Input 1 - DVD 0 LS Freq PEQ Level _____. □ . □ dB 63JHz PEQ Frequency 630Hz 2JJ Input 1 - DVD 2JJK □ DJ PEQ Bandwidth 0 .
Stream In addition to the six audio inputs on the rear panel, you can send an audio signal wirelessly ® ® ® through Zonetech to any zone using Bluetooth , AirPlay , UPnP and DLNA . This signal uses its own input channel. Bluetooth To pair/connect your Bluetooth device to Zonetech: 1. On Zonetech, press the Stream button to access the Stream settings. 2. Use the Left/Right (/) buttons to select the Stream Source (Source) setting. Then, turn the Info knob to select the Bluetooth option. 3.
AirPlay Select this option to connect a device to Zonetech using Apple AirPlay. 1. Make sure your AirPlay-enabled Apple device and Zonetech are powered on and connected to the same network. 2. On Zonetech, press the Stream button to access the Stream settings. 3. Use the Left/Right (/) buttons to select the Stream Source (Source) setting. Then, turn the Info knob to select the AirPlay option. 4. On your Apple device, select the AirPlay icon, then select Zonetech.
Editing Output (Zone) Settings You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the settings of each output (zone): To select a zone to edit, press the corresponding Zone button (1–6). The display will indicate which zone is selected: Zone 1–6. To show the previous or next setting for the selected zone, use the Left/Right (/) buttons (respectively). Turn the Info knob to adjust the value of each setting.
PEQ Level PEQ Frequency (PEQ Freq) This is the amount of “boost” (increase) or “cut” (decrease) of the mid-range parametric equalization band: -15.0 to +8.0 dB. This is the center frequency of the midrange parametric equalization band: 40 Hz – 16 kHz (default: 630 Hz). Zone 6 -Bar 0 - PEQ Frequency 630Hz PEQ Level 0.0dB LS Level 0.0c!B 20K PEQ Bandwidth (PEQ Band) High Shelf Level (HS Level) This is the width of the mid-range parametric equalization band: 0.300–4.000 oct (octaves) (default: 0.
Limiter Threshold (Threshold) Output Mode (Mode) (Zone 6 only) The limiter ensures the output audio signal does not exceed this volume level: -60.0 to 0.0 dB (default: 0.0 dB). This determines whether Zone 6’s output signal is stereo (left and right) (Stereo) or mono with two-way crossover (X-Over). Note: If a device (e.g., a power amplifier) later in the signal path than Zonetech is using a limiter, the limiter with a lower threshold will determine the maximum level.
Paging You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the paging settings. To view Paging settings, press the Page button. To edit the Paging settings, use the Left/Right (/) buttons to show the previous or next setting (respectively). Turn the Info knob to adjust the value of each setting. Note: To control the page settings remotely, you can also use a web-based interface on your computer (connected to the Computer Ethernet port), or an optional Rane RAD device (e.g.
High Shelf Level (HS Level) High Shelf Frequency (HS Freq) This is the amount of “boost” (increase) or “cut” (decrease) of the high-frequency shelving filter: -15.0 to +8.0 dB. This is the frequency of the highfrequency shelving filter: 630 Hz – 16 kHz (default: 630 Hz). Paging 0 PEO Freq 6::0Hz PEQ Ba nd .___ .___ 0.500 oct .15 High Shelf Level O.OdB High Shelf Frequency 63QHz ;,JK Chime Chime Level (CH Level) This determines whether the pager’s chime sound is on (Enabled) or off (Disabled).
Info You can use Zonetech’s display to view additional Zonetech system settings. Press the Info knob to cycle through the following information pages. These are the viewable Info settings. Meters Device/Port Status This view shows multicolor level meters for all inputs and zones. This view shows information about the devices currently connected to Zonetech and their current operations. Use this view to evaluate system faults, hardware errors, and other issues.
Wired Network Settings Wireless Network Settings This view shows the wired network address, subnet, and status. This view shows the wireless network address, subnet, and status. Important: When diagnosing or troubleshooting your system, always begin by reviewing this information and the Wireless Network Settings. Important: When diagnosing or troubleshooting your system, always begin by reviewing this information and the Wired Network Settings.
Controlling Zonetech Remotely There are a few different ways to control various Zonetech functions remotely: • You can use a computer to access a web-based interface to control all Zonetech functions. See Computer below. Note: Some controls are only available through the web interface. • You can use a Rane DR6 remote device to control all input levels, output (zone) levels, and zone source selections. See Master Remote below. • You can use a Rane DRZH to control the output (zone) functions.
These are the editable settings for Limited access mode: Master Outputs This page provides controls for output volume level and input audio source. . ! •1npu11 '"'"'' '"'"'' . ·-·_,_, . ¢ '"'"'' '"'"'' -·-· ! Master Outputs •1npu11 '"'"'' '"'"'' '"'"'' '"'"'' In Full access mode, click the tabs at the top of your web browser to navigate between pages. . ·-·_, . ! .... , ! .... , -· • Input ! " '', ,'_ lnpu! 5 ·-· .
Input 1–6, Stream, and Page (continued) Low Shelf Parametric EQ (PEQ) Level: This is the amount of “boost” (increase) or “cut” (decrease) of the lowfrequency shelving filter. Level: This is the amount of “boost” (increase) or “cut” (decrease) of the midrange parametric equalization band. Frequency: This is the center frequency of the low-frequency shelving filter. Frequency: This is the center frequency of the mid-range parametric equalization band.
Zones (Outputs) General 7 Level: This is the output volume level. Input Source: This is the audio source of the zone. Priority Source: This is the audio source that will play automatically when an incoming signal is detected. Priority Hold Time: This determines how long it will take (in seconds) for the output to switch back to the original audio source after the priority source signal falls below the threshold.
Zones (continued) Stereo/X-Over (Zone 6 only) Limiter Output Mode This determines whether Zone 6’s output signal is stereo (left and right) (Stereo) or mono with two-way crossover (X-Over). Threshold: The limiter ensures the output audio signal does not exceed this volume level. X-Over Frequency: This determines the frequency at which the low frequencies and high frequencies are split between the subwoofer and main loudspeaker.
Important: When diagnosing or troubleshooting your system, always begin by reviewing the Wired Network Settings and Wireless Network Settings below. Settings Device Information Wired Network Settings Firmware Version: This is current firmware version running on your Zonetech. DHCP IP and Subnet Mask: This is the dynamic IP address and subnet mask assigned through DHCP (Dynamic Host Configuration Protocol), if supported by your network. Serial Number: This is the serial number of your Zonetech unit.
Settings (continued) Configuration Firmware Update Save Settings: This allows you to save your system settings to a .zonetech file. Update Firmware: This allows you to check for firmware updates and update your Zonetech. Send Settings: This allows you to send saved settings to a Zonetech device. Master Remote You can use up to two Rane DR6 as master remote controls, allowing you to control all input levels, output (zone) levels, and zone source selections. Please visit rane.
Troubleshooting If you encounter a problem, try doing these things first: • Make sure all cables and other connected devices are properly and securely connected. • Make sure you are using Zonetech as described in this user guide. • Make sure your other devices or media are working properly. • If you believe Zonetech is not working properly, check the following table for your problem and solution. Problem: Solution: Please see: Power does not turn on.
Appendix Technical Specifications Audio Inputs Connectors (4) RCA stereo input pairs (1) 6-pin 3.8 mm Euroblock input (balanced mic/line level, green) Audio Outputs Maximum Input Level +20 dBu Connectors (3) 6-pin 3.8 mm Euroblock outputs (Zones 1–4 & 6, balanced line level, orange) (1) 3-pin 3.
Other Connectors (6) RJ45 ports (Zone 1–6 remote control via DRZH) (1) RJ45 port (master remote control) (1) RJ45 port (pager) (1) Ethernet port (computer) (1) 2-pin 3.8 mm Euroblock input (TTL [digital logic], black) (1) SMA antenna input (Bluetooth) (1) IEC power cable input Operating Temperature 32–95°F / 0–35°C (non-condensing) Power Connection IEC Voltage 100–240 VAC, 50/60 Hz Consumption 50 W Dimensions 19” x 8.7” x 1.7” (width x depth x height) 482 x 220 x 44 mm Weight 6.06 lb. 2.
rane.com Manual Version 1.
RANE) ZONETECH Quickstart Guide English (3–12) Guía de inicio rápido Español (13–22) Guide d'utilisation rapide Français (23–32) Guida rapida Schnellstart-Anleitung Appendix Italiano (33–42) Deutsch (43–52) English (53–54)
2
Quickstart Guide (English) Introduction Thank you for purchasing the Zonetech. At Rane, performance and reliability mean as much to us as they do to you. That’s why we design our equipment with only one thing in mind—to make your performance the best it can be. Box Contents ® Zonetech Bluetooth Antenna (1) 6-pin 3.8 mm Euroblock input Power Cable (green, for audio inputs) Quickstart Guide (3) 6-pin 3.8 mm Euroblock outputs (orange, for zone outputs) (1) 3-pin 3.
Features Front Panel 9 7 10 8 1 6 5 4 3 2 1. Display: This display shows information about Zonetech’s current status and options. 2. Power Light: This light is on when Zonetech is powered on. 3. Computer Link Light: This light is on when the Computer Ethernet port on the rear panel is connected to a computer (powered on). You can then use the computer to control Zonetech remotely using a web-based interface. 4.
Rear Panel 10 1. 2. 4 2 1 9 8 7 6 3 5 3 3 3 5 5 5 Power Input (IEC): Use a standard IEC cable to connect this input to a power outlet. Bluetooth Antenna Connector (SMA): Connect the included Bluetooth antenna here. Important: For compliance, you must use the included antenna only. No substitutions or modifications to the antenna are permitted. 3. Inputs (stereo RCA): Connect audio sources to these stereo input pairs. 4.
Operation Editing Input Settings You can use Zonetech’s display, Left/Right (/) buttons, and Info knob to edit the settings of each input. To select an input to edit, press the corresponding Input button (1–6) or the Stream button. The display will indicate which input is selected: Input 1–6 or Stream. To show the previous or next setting for the selected input, use the Left/Right (/) buttons (respectively). Turn the Info knob to adjust the value of each setting.
Bluetooth® In addition to the six audio inputs on the rear panel, you can send an audio signal wirelessly through Zonetech to any zone using Bluetooth. This signal uses its own input channel. IMPORTANT: Bluetooth and WiFi may not both be in use at the same time. When Bluetooth is enabled, WiFi will be disabled. To pair/connect your Bluetooth device to Zonetech: 1. On Zonetech, press the Stream button to access the Stream settings. 2.
Editing Output (Zone) Settings You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the settings of each output (zone): To select a zone to edit, press the corresponding Zone button (1–6). The display will indicate which zone is selected: Zone 1–6. To show the previous or next setting for the selected zone, use the Left/Right (/) buttons (respectively). Turn the Info knob to adjust the value of each setting.
Paging You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the paging settings. To view Paging settings, press the Page button. To edit the Paging settings, use the Left/Right (/) buttons to show the previous or next setting (respectively). Turn the Info knob to adjust the value of each setting. Note: To control the page settings remotely, you can also use a web-based interface on your computer (connected to the Computer Ethernet port), or an optional Rane RAD device (e.g.
Info You can use Zonetech’s display to view additional Zonetech system settings. Press the Info knob to cycle through the following information pages. Note: For the complete list of settings shown in the display and their functions, download the full User Guide. Meters This view shows multicolor level meters for all inputs and zones. Device/Port Status This view shows information about the devices currently connected to Zonetech and their current operations.
Controlling Zonetech Remotely There are a few different ways to control various Zonetech functions remotely: • You can use a computer to access a web-based interface to control all Zonetech functions. See Computer below. Note: Some controls are only available through the web interface. • You can use up to two Rane DR6 master remote controls to control all input levels, output (zone) levels, and zone source selections. Download the full User Guide or visit rane.com/HAL to learn more.
Troubleshooting If you encounter a problem, try doing these things first: • Make sure all cables and other connected devices are properly and securely connected. • Make sure you are using Zonetech as described in this Quickstart Guide. • Make sure your other devices or media are working properly. • If you believe Zonetech is not working properly, check the following table for your problem and solution. Problem: Solution: Please see: Power does not turn on.
Appendix (English) Technical Specifications Audio Inputs Connectors (4) RCA stereo input pairs (1) 6-pin 3.8 mm Euroblock input (balanced mic/line level, green) Audio Outputs Maximum Input Level +20 dBu Connectors (3) 6-pin 3.8 mm Euroblock outputs (Zones 1–4 & 6, balanced line level, orange) (1) 3-pin 3.
Other Connectors (6) RJ45 ports (Zone 1–6 remote control via DRZH) (1) RJ45 port (master remote control) (1) RJ45 port (pager) (1) Ethernet port (computer) (1) 2-pin 3.8 mm Euroblock input (TTL [digital logic], black) (1) SMA antenna input (Bluetooth) (1) IEC power cable input Operating Temperature 32–95°F / 0–35°C (non-condensing) Power Connection IEC Voltage 100–240 VAC, 50/60 Hz Consumption 50 W Dimensions 19” x 8.7” x 1.7” (width x depth x height) 482 x 220 x 44 mm Weight 6.06 lb. 2.
55
rane.com Manual Version 1.
RANE] PROCESSORS | ZONETECH - ONP U T ' ' ' ' •• cmc,M - '"" ""'""''°""'""'' ◄ ZO N E - l DAOUC\ · ~ ZO N ETEC H i~~r~~~~ • • MAOf 1NCHNA ZONETECH ~ • ,..., """"', IL.A SQMH:SO~AHS .2 I!:\ \ZI 1 i,\ I 3 4 ,...,..., k...a....111 IN~U e ' 0*'" 6PAGE C> PAGER MASTER REMOTE • - ONPUTS ZONE REMOTES 6 s 4 3 2 1 ~ ~ SHOFlOrncus,oRaFTTF R CLASS2 WIRNG (}•R• ;! ~•R5 :!1 LOGIC INPUT tu ::·.:::, ' ,- " tr"\ A' c::=J ~·1 , 2 ov■ HI OUTPUTS ~· ·1 " ' 'I " ~' 'I fr
PROCESSORS | ZONETECH RANE] Audio Inputs Connectors (1) 6-pin 3.8 mm Euroblock input (balanced mic/line level, green) (4) RCA stereo output pairs Audio Outputs Maximum Input Level +20 dBu Connectors (3) 6-pin 3.8 mm Euroblock outputs (Zones 1–4 & 6, balanced line level, orange) (1) 3-pin 3.
RANE] Important Safety Instructions & Warranty Information English ( 3 - 7 ) lnstrucciones importantes de seguridad e informaci6n de la garantra Espanol ( 8 - 11 ) Instructions importantes de securite et informations de garantie Fran~ais ( 12-15) lstruzioni importanti di sicurezza e le informazioni della garanzia Italiano ( 16-19) ; r .
Rane is a trademark of lnMuslc Brands, Inc., registered In the U.S. and other countries. NEMA• is the registered trademark and service mark of the National Electrical Manufacturers Association. All other product names, company names, trademarks, or trade names are those of their respective owners.
Product Warranty HANEi (for products purchased in the U.S.A.) 1. What la covered and for how long? All Products: lnMuslc Brands, Inc. C-inMuslcj warrants to the original purchaser that Rane products and all other accessories are free from defects In material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized Rane dealer and continuing for the following period of time after that date for one (1) year.
HANEi Product Warranty (for products purchased outside of the U.S.A.) 1. inMusic Brands; Inc. ("inMusicj warrants to the original purchaser that Rane products are free from defects in material and workmanship under normal use and service for the per,iod commencing upon the date of purchase from an authorized Rane dealer and continuing for the following period of time after that date for (1) Year. 2. This Limited Warranty is conditioned upon proper use of the product by the purchaser.
Return lnfonnation • A retum merchant authorization number must be obtained from your local Rane representative. For your representative go to rane.com. · A copy of the original sales receipt must also be included for the equipment to be repaired under warranty. Toe faulty equipment must be packed in its original packaging. • One additional outer layer of packaging must be included to ensure product safety.
14. Water and Moisture (If applicable): This product should be kept away from direct contact with liquids. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. 15. Caution (If applicable): Danger of explosion if battery is Incorrectly replaced. Replace only with the same or equivalent type. Batteries (a battery pack or an installed battery) shall not be exposes to excessive heat such as sunshine, fire, etc. 16.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. For Canadian models: • This device complies with Industry Canada licence-exempt RSSs.
Wor1d Headquarters inMusic Brands, Inc. 200 Scenic View Drive Cumberland, RI 02864 USA Tel: 401-658-8192 Fax: 401-658-3640 U.K. Office inMusic Europe, Ltd. Unit 3, Nexus Park Lysons Avenue Ash Vale HAMPSHIRE GU12 5QE UNITED KINGDOM Tel: 01252 896 040 Fax: 01252 896 021 Germany Office inMusic GmbH Harkortstr. 12 - 32 40880 Ratingen GERMANY Tel: 02102 7402 20150 Fax: 02102 7402 20011 rane.
