User's Manual
Table Of Contents
- 4. - ST-3118 RF DESCRIPTION
- 4.1. Circuit Configuration
- 4.2. Receiver System
- 4.2.1. Front-end RF Receiver
- 4.2.2. ANALOG Audio Processing
- 4.2.3. Virtual Squelch Circuit
- 4.2.4. Virtual VOLUME CONTROL
- 4.2.5. Sub audio signaling
- 4.2.6. ANALOG AUDIBLE SIGNALING
- 4.2.7. DIGITAL AUDIO PROCESSING
- 4.3. Transmitter System
- 4.3.1. ANALOG TX SIGNAL
- 4.3.2. DIGITAL TX AUDIO:
- 4.3.3. Drive and Final Amplifier Stages
- 4.3.4. Automatic Transmit Power Control
- 5. ST-3118 ALIGNMENT
- 5.1. Introduction
- 5.2. ALIGNMENT:
- 5.3. Required Test Equipment
- 5.4. Alignment Procedure
- 5.4.1. GENERAL ALIGNMENT CONSIDERATIONS:
- 5.5. MAIN RADIO ALIGNMENT
- 5.6. TRANSMITTER ALIGNMENT:
- 5.6.1. Main Clock alignment:
- 5.6.2. Transmit Power alignment:
- 5.6.2.1. High POWER LEVEL ALIGNMENT
- 5.6.2.2. Mid POWER LEVEL ALIGNMENT
- 5.6.2.3. LOW POWER LEVEL ALIGNMENT
- 5.6.3. ANALOG MAXIMUM DEVIATION
- 5.6.4. Modulation Gain alignment:
- 5.6.5. FDMA DATA MODULATION alignment:
- 5.6.6. TDMA DATA MODULATION alignment:
- 5.6.7. EIA tones Level Alignment:
- 5.6.8. DTMF signaling level alignment:
- 5.6.9. DCS signaling alignment:
- 5.6.10. CTCSS signaling alignment
- 5.6.11. FSK signaling alignment:
- 5.7. RECEIVER ALIGNMENT
- 5.7.1. DISCRIMINATOR GAIN
- 6. COMPLIMENTARY USER ALIGNMENT
- 6.1. OPTION ALIGNMENT:
- 6.1.1. ANALOG Microphone gain:
- 6.1.2. ANALOG External Mic Gain:
- 6.1.3. Analog AGC
- 6.1.4. DIGITAL AGC
- 6.1.5. MINIMUM VOLUME LEVEL:
- 6.1.6. SQUELCH LEVEL:
- 6.1.7. DISABLE RF POWER
- 7. RADIO APPEARANCE ALIGNMENT
- 7.1. DISPLAYS AND LEDS:
- 7.1.1. Auto backlight delay alignment:
- 7.1.2. Power on Text:
- 7.1.3. Leds:
- 7.2. Tones
- 7.3. ANNUNCIATION
ST-3118C SM R 1.1 SMARTRUNK SYSTEMS, INC.
21
Press Start then move the slider to
reach the desired value at the time
you checks the deviation meter to
reach the desired signaling level for
narrow band operation. Radio will
generate 134.4Hz audio tone for
alignment proposes.
As soon the desired value is
reached, press [Finish] to store the
value on radio memory.
Default value corresponds to 300Hz
deviation for narrow band
channels.
If you want to retrieve factory
default, press [Factory] instead of
[Start]. You will be asked to confirm
the factory default alignment, and
then if you confirm it, original
values from factory will be loaded
into current alignment settings.
5.6.10. CTCSS signaling
alignment
CTCSS signaling encoded from ST-
3118 can be aligned by selecting
CTCSS Level
alignment option form the
alignment menu.
Actual alignment value will be
displayed on alignment slider.
Press [Start] then move the slider to
reach the desired value at the time
you checks the deviation meter to
reach the desired signaling level for
narrow band operation. Radio will
generate 123.0Hz audio tone for
alignment proposes.
As soon the desired value is
reached, press [Finish] to store the
value on radio memory.
Default value corresponds to 300Hz
deviation for narrow band
channels.
If you want to retrieve factory
default, press [Factory] instead of
[Start]. You will be asked to confirm
the factory default alignment, and
then if you confirm it, original
values from factory will be loaded
into current alignment settings.
5.6.11. FSK signaling
alignment:
To align FSK/PSK signaling
deviation, select
FSK Mod Level
on Alignment screen.
Figure 23: FSK Modulation Level Alignment Screen
Actual alignment value will be
displayed on alignment slider.
Figure 22: CTCSS Level Alignment Screen