User's Manual
Table Of Contents
- 4. - ST-3118 RF DESCRIPTION
- 4.1. Circuit Configuration
- 4.2. Receiver System
- 4.2.1. Front-end RF Receiver
- 4.2.2. ANALOG Audio Processing
- 4.2.3. Virtual Squelch Circuit
- 4.2.4. Virtual VOLUME CONTROL
- 4.2.5. Sub audio signaling
- 4.2.6. ANALOG AUDIBLE SIGNALING
- 4.2.7. DIGITAL AUDIO PROCESSING
- 4.3. Transmitter System
- 4.3.1. ANALOG TX SIGNAL
- 4.3.2. DIGITAL TX AUDIO:
- 4.3.3. Drive and Final Amplifier Stages
- 4.3.4. Automatic Transmit Power Control
- 5. ST-3118 ALIGNMENT
- 5.1. Introduction
- 5.2. ALIGNMENT:
- 5.3. Required Test Equipment
- 5.4. Alignment Procedure
- 5.4.1. GENERAL ALIGNMENT CONSIDERATIONS:
- 5.5. MAIN RADIO ALIGNMENT
- 5.6. TRANSMITTER ALIGNMENT:
- 5.6.1. Main Clock alignment:
- 5.6.2. Transmit Power alignment:
- 5.6.2.1. High POWER LEVEL ALIGNMENT
- 5.6.2.2. Mid POWER LEVEL ALIGNMENT
- 5.6.2.3. LOW POWER LEVEL ALIGNMENT
- 5.6.3. ANALOG MAXIMUM DEVIATION
- 5.6.4. Modulation Gain alignment:
- 5.6.5. FDMA DATA MODULATION alignment:
- 5.6.6. TDMA DATA MODULATION alignment:
- 5.6.7. EIA tones Level Alignment:
- 5.6.8. DTMF signaling level alignment:
- 5.6.9. DCS signaling alignment:
- 5.6.10. CTCSS signaling alignment
- 5.6.11. FSK signaling alignment:
- 5.7. RECEIVER ALIGNMENT
- 5.7.1. DISCRIMINATOR GAIN
- 6. COMPLIMENTARY USER ALIGNMENT
- 6.1. OPTION ALIGNMENT:
- 6.1.1. ANALOG Microphone gain:
- 6.1.2. ANALOG External Mic Gain:
- 6.1.3. Analog AGC
- 6.1.4. DIGITAL AGC
- 6.1.5. MINIMUM VOLUME LEVEL:
- 6.1.6. SQUELCH LEVEL:
- 6.1.7. DISABLE RF POWER
- 7. RADIO APPEARANCE ALIGNMENT
- 7.1. DISPLAYS AND LEDS:
- 7.1.1. Auto backlight delay alignment:
- 7.1.2. Power on Text:
- 7.1.3. Leds:
- 7.2. Tones
- 7.3. ANNUNCIATION
ST-3118C SM R 1.1 SMARTRUNK SYSTEMS, INC.
28
7. RADIO APPEARANCE
ALIGNMENT
Under user mode, login radio
appearance can be aligned.
Select Edit then appearance from
radio top toolbars to access to the
appearance screen:
Figure 33: Access to the Appearance Menu
A soon as Appearance option is
selected, a new window will pop up:
Figure 34: Display/Leds Appearance Screen
7.1. DISPLAYS AND LEDS:
This screen lets you adjust the
behavior of the display backlight,
Power On text and TX/RX LEDs.
7.1.1. Auto backlight delay
alignment:
The auto backlight mode,
automatically set on power off
status to the backlight, after any
event, to reduce the battery
demand.
To change the value of the delay
before the backlight is powered off;
please enter the quantity of desired
seconds for it.
7.1.2. Power on Text:
Type here the text to show on the
display when the radio is powered
on.
This string is very convenient for
radio identification or dealer
advertising at the time the radio is
powered on.
The option to activate or deactivate
the power on text is disabled.
7.1.3. Leds:
Allows the user to disable the
function of Rx and TX led. Some
application, as security, sometime
demands no lights on the radio.
7.2. Tones