User's Manual
Table Of Contents
- 4. - ST-3118 RF DESCRIPTION
- 4.1. Circuit Configuration
- 4.2. Receiver System
- 4.2.1. Front-end RF Receiver
- 4.2.2. ANALOG Audio Processing
- 4.2.3. Virtual Squelch Circuit
- 4.2.4. Virtual VOLUME CONTROL
- 4.2.5. Sub audio signaling
- 4.2.6. ANALOG AUDIBLE SIGNALING
- 4.2.7. DIGITAL AUDIO PROCESSING
- 4.3. Transmitter System
- 4.3.1. ANALOG TX SIGNAL
- 4.3.2. DIGITAL TX AUDIO:
- 4.3.3. Drive and Final Amplifier Stages
- 4.3.4. Automatic Transmit Power Control
- 5. ST-3118 ALIGNMENT
- 5.1. Introduction
- 5.2. ALIGNMENT:
- 5.3. Required Test Equipment
- 5.4. Alignment Procedure
- 5.4.1. GENERAL ALIGNMENT CONSIDERATIONS:
- 5.5. MAIN RADIO ALIGNMENT
- 5.6. TRANSMITTER ALIGNMENT:
- 5.6.1. Main Clock alignment:
- 5.6.2. Transmit Power alignment:
- 5.6.2.1. High POWER LEVEL ALIGNMENT
- 5.6.2.2. Mid POWER LEVEL ALIGNMENT
- 5.6.2.3. LOW POWER LEVEL ALIGNMENT
- 5.6.3. ANALOG MAXIMUM DEVIATION
- 5.6.4. Modulation Gain alignment:
- 5.6.5. FDMA DATA MODULATION alignment:
- 5.6.6. TDMA DATA MODULATION alignment:
- 5.6.7. EIA tones Level Alignment:
- 5.6.8. DTMF signaling level alignment:
- 5.6.9. DCS signaling alignment:
- 5.6.10. CTCSS signaling alignment
- 5.6.11. FSK signaling alignment:
- 5.7. RECEIVER ALIGNMENT
- 5.7.1. DISCRIMINATOR GAIN
- 6. COMPLIMENTARY USER ALIGNMENT
- 6.1. OPTION ALIGNMENT:
- 6.1.1. ANALOG Microphone gain:
- 6.1.2. ANALOG External Mic Gain:
- 6.1.3. Analog AGC
- 6.1.4. DIGITAL AGC
- 6.1.5. MINIMUM VOLUME LEVEL:
- 6.1.6. SQUELCH LEVEL:
- 6.1.7. DISABLE RF POWER
- 7. RADIO APPEARANCE ALIGNMENT
- 7.1. DISPLAYS AND LEDS:
- 7.1.1. Auto backlight delay alignment:
- 7.1.2. Power on Text:
- 7.1.3. Leds:
- 7.2. Tones
- 7.3. ANNUNCIATION
FCC Notices
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment
Use only shielded cables to connect I/O device to this equipment. You are cautioned that
changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
RF exposure warning ยท
This equipment must be installed and operated in accordance with provided instructions
and the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 105 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must be
provide with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.