Specifications

ManualsBrandsRanger Products ManualsAir CompressorR7580V-603

EXTREME-DUTY

AIR COMPRESSORS

LS580V-601

LS7580V-601

LS580V-501

LS7580V-501

LS580V-603

LS7580V-603

LS580V-503

LS7580V-503

INSTALLATION AND OPERATION MANUAL

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes

to the purchaser upon receipt from the carrier.

Consequently, claims for the material damaged in

shipment must be made by the purchaser against

the transportation company at the time shipment

is received.

BE SAFE

Your new BendPak air compressor was designed and

built with safety in mind. However, your overall

safety can be increased by proper training and

thoughtful operation on the part of the operator.

DO NOT operate or repair this equipment without

reading this manual and the important safety

instructions shown inside.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

Fax: 1-805-933-9160

www.bendpak.com

Keep this operation manual near the

machine at all times. Make sure that ALL

USERS read this manual .

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO

INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT

YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF

THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO

OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

REV 09-09-010

PN# 5900112

Summary of content (16 pages)

PAGE 1
PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
PAGE 2
This page intentionally left blank.
PAGE 3
DESCRIPTION Air compressor units are intended to provide compressed air to power pneumatic tools, operate spray guns and supply air for pneumatic valves and actuators. The pumps supplied with these units have oil lubricated bearings. A small amount of oil carryover is present in the compressed air stream. Applications requiring air free of oil vapor should have the appropriate filter installed. The air compressor units are to be mounted per the instructions provided on a solid floor.
PAGE 4
GENERAL SAFETY 13. Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and inspect periodically for unsafe conditions such as rust formation and corrosion. Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc.) may be under high pressure and be subject to explosions, the following safety precautions must be observed at all times: 14. STAY ALERT. Watch what you are doing. Use common sense. Be aware. 1.
PAGE 5
SPRAYING PRECAUTIONS TANK MOUNTING 1. Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system. The tank should be bolted into a flat, even, concrete floor or on a separate concrete foundation. Anti-vibration pads should be used between the tank leg and the floor. When using anti-vibration pads, do not draw bolts tight. Allow the pads to absorb vibrations.
PAGE 6
WIRING All wiring and electrical connections must be performed by a qualified electrician. Installations must be in accordance with local and national codes. Overheating, short circuiting and fire damage will result from inadequate wiring. Wiring must be installed in accordance with National Electrical Code and local codes and standards that have been set up covering electrical apparatus and wiring. Be certain that adequate wire sizes are used, and that: INSTALLING A SHUT-OFF VALVE 1.
PAGE 7
DIRECTION OF ROTATION Recommended wire sizes may be larger than the minimum set up by local ordinances. If so, the larger size wire should be used to prevent excessive line voltage drop. The additional wire cost is very small compared with the cost of repairing or replacing a motor electrically “starved” by the use of supply wires which are too small. To change to the alternate voltage on three phase motors with 230/460 ratings. The voltage and amperage ratings are listed on the motor nameplate.: 1.
PAGE 8
LUBRICATION AIR TANK SAFETY VALVE If the pressure switch does not shut off the air compressor at its cut-out pressure setting, the safety valve will protect against high pressure by “popping off” at its factory set pressure (slightly higher than the pressure switch cut-out setting). THIS UNIT CONTAINS NO OIL. Before operating compressor. Fill to the center of the sight gauge or maximum mark on dipstick.
PAGE 9
BREAK-IN PROCEDURES OPERATING PROCEDURES This procedure is required before the air compressor is put into service, before the hose is installed, the check valve is replaced, or a complete compressor pump is replaced. Daily Start-Up Checklist 1. Check oil and add if necessary. 2. Before attaching an air hose or accessory, make sure the shut-off valve is in the closed position. Make sure the ON/ AUTO lever is in the OFF position.
PAGE 10
DRAIN AIR TANK DAILY. Water will condense in the air tank. If not drained, the water will corrode and weaken the air tank, causing a risk of air tank rupture. The air tank must be drained properly. if the air compressor is under continuous use, drain at least once each day. If the air compressor is only used occasionally, drain after each use. If the tank drain valve is clogged, first release the air pressure in the air tank. The tank drain valve can then be removed, cleaned and reinstalled.
PAGE 11
AIR FILTER Never run the compressor pump without an intake air filter nor with a clogged intake air filter(s). Use compressed air to blow the filters clean. Do not wash or oil the element. If it cannot be blown clean, the filter(s) must be replaced. Operating compressor with a dirty filter can cause high oil consumption and increase oil contamination in the discharge air. INTERCOOLER TUBING Intercooler fins are very sharp. Always wear gloves and use care when you clean or work near the intercooler tubing.
PAGE 12
PAGE 13
LIMITED WARRANTY 1. DURATION: From the date of purchase by the original purchaser. Any BendPak Extreme Duty Tri-Max air compressor: >Five Year warranty on the compressor tank only > Two Year warranty on the compressor pump only, against defects in material or workmanship under normal use and service, from the date of installation or 24 months from the date of shipment by BendPak or a BendPak distributor whichever comes first. 2. WHO GIVES THIS WARRANTY (WARRANTOR): BendPak Inc., 1645 Lemonwood Dr.
PAGE 14
MAINTENANCE / INSPECTION RECORDS ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ _________________________________________________________________
PAGE 15
This page intentionally left blank.
PAGE 16
For Parts or Service Contact: BendPak Inc. / Ranger Products, 1645 Lemonwood Dr. Santa Paula, CA. 93060 Tel: 1-805-933-9970 Toll Free: 1-800-253-2363 Fax: 1-805-933-9160 www.bendpak.com www.rangerproducts.