Specification

1
PRODUCT DATASHEET
DESCRIPTION: Rapid Set
®
CEMENT ALL
®
is a high-performance, fast-setting, multi-
purpose concrete repair material and non-shrink grout. Durable in wet environments,
CEMENT ALL is a blend of Rapid Set hydraulic cement and specially graded ne
aggregates. CEMENT ALL is non-metallic and no chlorides are added. Mix CEMENT ALL
with water to produce a workable, high quality material that is ideal where rapid strength
gain and high durability are desired. CEMENT ALL sets in 15 minutes and achieves
structural strength in 1 hour.*
USES: Use CEMENT ALL for general and structural concrete repair, doweling and
anchoring, industrial grouting, formed work, vertical and horizontal trowel applications.
CEMENT ALL is ideal for airport, highway, industrial and marine applications.
ENVIRONMENTAL ADVANTAGES: Use CEMENT ALL to reduce your carbon footprint
and lower your environmental impact. Production of Rapid Set cement emits far
less CO
2
than portland cement. Contact your representative for LEED values and
environmental information.
APPLICATION: Apply CEMENT ALL in thicknesses from featheredge to 4” (10 cm). For
heavy loads and vehicle trafc, minimum thickness will vary. Not intended for high heat
applications above 300°F (149°C). For deeper sections, use Rapid Set
®
Mortar Mix or
Rapid Set
®
Concrete Mix. For overlay applications, a minimum of one test section should
be prepared to evaluate the suitability of the materials and procedures.
SURFACE PREPARATION: For repairs, application surface must be clean, sound and free
from any materials that may inhibit bond, such as oil, asphalt, curing compound, acid,
dirt and loose debris. Roughen surface and remove all unsound material. Apply CEMENT
ALL to a surface that is thoroughly saturated with no standing water.
MIXING: The use of a power-driven mechanical mixer, such as a mortar mixer or a drill-
mounted mixer, is recommended. Organize work so that all personnel and equipment are
in place before mixing. Use clean potable water. CEMENT ALL may be mixed using 3 to
5 quarts (2.8 L to 4.7 L) of water per 55-lb (25-kg) bag. Use less water to achieve
higher strengths. Do not exceed 5 quarts (4.7 L) of water per bag. For increased
uidity and workability, use Rapid Set
®
FLOW Control
®
plasticizing admixture from the
Rapid Set
®
Concrete Pharmacy
®
. Place the desired quantity of mix water into the mixing
container. While the mixer is running, add CEMENT ALL. Mix for the minimum amount of
time required to achieve a lump-free, uniform consistency (usually 1 to 3 minutes). Do
not retemper.
PLACEMENT: CEMENT ALL may be placed using traditional construction methods.
Organize work so that all personnel and equipment are ready before placement. Place,
consolidate and screed quickly to allow for maximum nishing time. Use a method of
consolidation that eliminates air voids. Do not wait for bleed water; apply nal nish
as soon as possible. CEMENT ALL may be troweled, oated or broom nished. On at
work, do not install in layers. Install full-depth sections and progress horizontally. Do not
install on frozen surfaces. To extend working time, use Rapid Set
®
SET Control
®
retarding
admixture from the Concrete Pharmacy or cold mix water. CEMENT ALL may be applied
in temperatures ranging from 45°F to 90°F (7°C to 32°C).
CEMENT ALL
Multi-Purpose Repair Material & Non-Shrink Grout
PRODUCT CATALOG
REPAIR &
RESTORATION
OVERVIEW
Highlights:
Fast: Sets in 15 minutes, structural strength
in 1 hour*
Durable: Formulated for long life
in critical applications
Excellent Bond: Superior adhesion to concrete,
stone, brick, block, stucco and more
Structural: For repair and new construction
Multi-Purpose: Use for concrete repair, grouting,
anchoring, casting, underlayment and more
Conforms to:
ASTM: C1107, C928, C387 and CRD C621
Army Corps of Engineers
LA Research and Report 24654
State and Local Approvals
MasterFormat
®
2016
03 01 30 Maintenance of Cast-in-Place Concrete
03 01 40 Maintenance of Precast Concrete
03 01 60 Maintenance of Grouting
03 01 70 Maintenance of Mass Concrete
03 53 19 Concrete Overlayment
03 54 16 Hydraulic Cement Underlayment
03 60 00 Grouting
03 61 00 Cementitious Grouting
03 62 13 Non-Metallic Non-Shrink Grouting
04 01 00 Maintenance of Masonry
Manufacturer:
CTS Cement Manufacturing Corp.
12442 Knott St.
Garden Grove, CA 92841
Tel: [phone] | Fax: [phone]
Web: www.CTScement.com
E-mail: [e-mail]