Operating instructions

ManualsBrandsRasmussen ManualsHome building and DecorChillbuster 7

AGA "CHILLBUSTER I"

12028 E. Philadelphia St. Whittier , CA 90601 U.S.A.

(562) 696-8718 FAX (562) 698-3510

E-Mail: gaslogs@riwinc.com Web http://www.riwinc.com

CB-1 2-03

Assembly, Installation, and Operation

Instructions for Rasmussen "Single Burner"

Manual, Switch, or Remote

Natural and Propane Gas Log Room Heater Models:

18" or 24" SINGLE BURNER Manual Control (K,W,KW)(18, 24)-C1A,C-M-(N,P)

30" SINGLE BURNER Manual Control (K,W,KW)(30)-C1B,D-M-(N,P)

18", 24" or 30" DOUBLE FACE Manual Control DF(K,W,C)(18,24,30)-DFC1,C1C-M-(N,P)

18" or 24" SINGLE BURNER Switch Control (K,W,KW)(18, 24)-C1A,C-S-(N,P)

30" SINGLE BURNER Switch Control (K,W,KW)(30)-C1B,D-S-(N,P)

18", 24" or 30" DOUBLE FACE Switch Control DF(K,W,C)(18, 24, 30)-DFC1,C1C-S-(N,P)

30" SINGLE BURNER Remote Control (K,W,KW)(30)-C1B,D-R-(N,P)

18" or 24" SINGLE BURNER Remote Control (K,W,KW)(18, 24)-C1A,C-R-(N,P)

18", 24" or 30" DOUBLE FACE Remote Control DF(K,W,C)(18, 24, 30)-DFC1,C1C-R-(N,P)

Read these Instructions carefully and retain them for future use.

THESE GAS LOG HEATERS ARE CERTIFIED TO THE FOLLOWING STANDARDS:

• UNVENTED ROOM HEATER ANSI Z21.11.2a 2001

• VENTED DECORATIVE APPLIANCE ANSI Z21.60b 2001 * CGA 2.26b-2001

Design certified for installation only in a solid-fuel burning masonry or UL 127 factory-built fireplace or

in a listed ventless firebox enclosure.

DO NOT install this appliance in a factory-built fireplace that includes instructions stating it has not been

tested or should not be used with unvented gas logs.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life .

WARNING:

Improper installation, adjustment,

alteration, service or maintenance can cause

property damage, personal injury or loss of life. Read

these instructions thoroughly before installation.

For assistance or additional information, consult

your gas log dealer, qualified installer, service

agency or gas supplier.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbors phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier,

call the fire department.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance..

INSTALLATION AND SERVICE: Installation and service must be performed by a

qualified installer, service agency or the gas supplier..

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is

installed. Provisions for adequate combustion and ventilation air must be provided.

Refer to Section "PROVISIONS FOR ADEQUATE COMBUSTION AND VENTILATION

AIR" (pages 4 and 5.) .

Summary of content (13 pages)

PAGE 1
CB-1 2-03 AGA "CHILLBUSTER I" 12028 E. Philadelphia St. Whittier , CA 90601 U.S.A. (562) 696-8718 FAX (562) 698-3510 E-Mail: gaslogs@riwinc.com Web http://www.riwinc.
PAGE 2
ALL APPLICATIONS (VENTED and VENT FREE OPERATION) IMPORTANT NOTICE • • • Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the hazard of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room with the appliance. "WARNING: Any change to this heater or its controls can be dangerous.
PAGE 3
ALL APPLICATIONS (VENTED and VENT FREE OPERATION) 9. The CHILLBUSTER and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The CHILLBUSTER must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa). 10.
PAGE 4
VENT FREE OPERATION PROVISIONS FOR ADEQUATE COMBUSTION AND VENTILATION AIR This heater shall not be installed in a "confined" space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Confined Or Unconfined Space Determination: The National Fuel Gas Code defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.
PAGE 5
VENT FREE OPERATION COMBUSTION AIR CALCULATIONS WORKSHEET 1. 1a. 1b. 1c. 1d. 2. 3. 4. Room Width Length Height W x L x H=Vol. (ft3 ) Total Volume (ft 3 )sum of Volume (ft3 ) of all rooms (sum lines 1a. thru 1d.) 2 . Max Supportable Btu/Hr=Total Volume (ft3 ) ÷ 50 x 1000 (line 2 ÷ 50 x1000) 3 . 3 3 3 4a. Btu/hr 4 b . Btu/hr 4 c . Btu/hr 4 d . 3 Btu/hr Actual Btu/hr used = Sum Btu/hr of all fuel burning appliances inside the space identified as rooms 1a. thru 1.b (sum line 4a thru 4d.) 4 . 5 .
PAGE 6
VENT FREE OPERATION FIREPLACE HOODS A fireplace hood deflects heat away from the fireplace face and mantel, reducing the potential for heat related warping or discoloration. The use of a fireplace hood is highly recommended. Fireplace Hoods are offered by many leading fireplace manufacturers.
PAGE 7
ALL APPLICATIONS (VENTED and VENT FREE OPERATION) LOG PLACEMENT C1A, C1C, C1B, and C1D 1. 18" sets have 5 logs. 24" sets have six logs. 2. Place largest log (FRONT LOG) in the front of the grate and the second largest log (REAR LOG) on the rear of the grate behind the LOCATOR PINS. (Figures 5 and 6). 3. Place both Right and Left LARGE TOP LOGs across the FRONT and REAR logs with the LOCATOR PINS inserted into the drilled holes located on the bottom of both LARGE TOP LOGs. (Figures 5 and 6). 4.
PAGE 8
ALL APPLICATIONS (VENTED and VENT FREE OPERATION) DFC1 and DFC1C (Double Face) Log Placement (continued): Small Top Logs Large Top Log . . v v . Small Top Logs v v v Top Logs Small Large v Top Log Front Log Top Log Large v Front Logs v Burner Top Logs Small . .
PAGE 9
ALL APPLICATIONS (VENTED and VENT FREE OPERATION) Millivolt Pilot Lighting (continued): PILOT ADJUST 6. Press Piezo Ignitor Button to Figure 12 COVER CAP light pilot. Continue to hold in the + + + Gas Cock Dial until the Pilot flame remains lit when knob is released PILOT (approximately 60 to 90 seconds). If Pilot does not remain lit, repeat steps + + + 1 through 5 and allow more time after Pilot Lighting before releasing knob. + + + 7. Turn Gas Cock Dial to "ON".
PAGE 10
ALL APPLICATIONS (VENTED and VENT FREE OPERATION) Pilot Adjustment and Operation: THERMOGENERATOR (Switch Models) PILOT FLAME The Pilot flame should be steady and soft blue surrounding 1/8 inch of the thermocouple tip as shown in Figure 15. OP AMERICA Standard (Manual Models): 1. To adjust, insert a narrow long stem screw driver throughPilot AIR INTAKE Access Port (see figure 10) to turn pilot adjustment screw . HOLES 2. Turn clockwise for less pilot flame. LP THEMOCOUPLE 3.
PAGE 11
HOW TO ORDER PARTS Parts can be ordered through the supplier from whom you purchased your CHILLBUSTER. When ordering parts, always specify (From information available on name plate attached to grate) the following: 1. Model number of the CHILLBUSTER. 2. Serial number of the CHILLBUSTER. 3. Type of gas (natural or propane Gas). 4. The name of the part and part number from parts list. Save these instructions Manufactured By: RASMUSSEN IRON WORKS, INC. 12028 E.
PAGE 12
TWO YEAR CONSUMER PRODUCT WARRANTY The following warranty has been drafted to comply with the MAGNUSON-MOSS WARRANTY ACT applicable to products manufactured after July 4, 1975. It replaces and supersedes any warranty in this package or in any printed literature. LIMITED WARRANTY: RASMUSSEN IRON WORKS INC, 12028 E. Philadelphia Street, Whittier California, U.S.A..
PAGE 13
CPW-CB-2-96 CHANGES (next) page 1: standard update z21.11.2a 2001 DUE 4-03; standard update z21.11.