Specifications

Locating & Assembling the Grill
Page 3
When determining a suitable location,
take into account concerns such as
exposure to wind, proximity to traffic
paths and keeping any gas supply lines
as short as possible. Locate the grill
only in a well-ventilated area. Never
locate the grill in a building, garage,
breezeway, shed or other such enclosed
areas with out an approved ventilation
system. During heavy use, the grill will
produce a lot of smoke.
CLEARANCE
To Non-Combustible Construction
A minimum of 3” clearance from the
back of the grill to non-combustible
construction is required for the lid to
open fully.
To Combustible Construction
Do not install this unit into combustible
enclosures without the use of a suitable
insulated jacket or by maintaining a
minimum clearance of 12” between
the grill and any combustible materials.
If your enclosure is combustible, then the
installation of an INSULATED JACKET
manufactured by SOLAIRE INFRARED
GRILLING SYSTEMS, is required.
Please refer to the cut out sizes for
INSULATED JACKETS on Page 18.
ASSEMBLY
Built-in Models
Before locating your SOLAIRE
INFRARED Grill into your Non-
Combustible enclosure, complete the
following steps:
1.Remove all packaging materials.
2.Ensure that the burners are positioned
correctly on their orifices, and are
fully seated onto their supports.
3.Ensure that a NEW battery is fitted
to the push button igniter. (See
Figure 1 below).
4.Install regulator onto manifold at
back of grill using pipe thread
compound or teflon tape on the
threads (see Fig. 2+3 below).
5.Ensure regulator is set for proper
gas type (see Fig. 11 on pg. 16).
6.Make the connection to the gas
regulator at the rear of the Grill with
a flexible connector. Ensure that the
connection is tight.
Your SOLAIRE INFRARED Grill can
now be located into the enclosure.
Pass the flexible gas connector
through the access hole located in
the support base of the enclosure for
final connection to the gas supply.
Free Standing Models
Your SOLAIRE INFRARED Grill has
provision for mounting onto the mobile
pedestal by bolting from the side. With
the help of an assistant set the grill on
the mobile pedestal. Align the mounting
holes on the side of the Grill with the
holes on the side of the mobile pedes-
tal. Once mounted, secure the grill to
the mobile cart with the four bolts pro-
vided and tighten securely.
Complete the following steps:
1.Remove all packaging materials.
2.Ensure that the burners are positioned
correctly on their orifices, and are
fully seated onto their supports.
3.Ensure that a NEW battery is fitted
to the push button igniter. (See
Figure 1 below).
4.Install regulator onto manifold at
back of grill using pipe thread
compound or teflon tape on the
threads (see Fig. 2+3 below).
5.Ensure regulator is set for proper
gas type (see Fig. 11 on pg. 16).
6.Make the connection to the gas
regulator at the rear of the Grill with
a flexible connector. Ensure that the
connection is tight.
AABattery
Insert negative end of AA
battery into main body of
ignitor first.
Front Control Panel
Figure 1
Igniter Battery
Installation Instructions:
Stretch spring to
ensure electrical
contact
Page 18
Built-in Cutout Details
36
18
1
/
4
B
3
5
/
8
3
7
/
8
(see note)
8
7
/
8
A
26
Grill Cutout
Dimension A
Model AGBQ-27 16 1/4”
Model AGBQ-27XL 21”
Access Doors
Dimension B
Model IRAD-21 18 1/4”
Model IRAD-30 27 1/4”
Model IRAD-42 39 1/4”
SERVICE REQUIREMENTS
Gas Service Line:
1/2” NPT
Gas Pressure:
4.0” W.C. natural gas
10.0” W.C. propane
Non-combustible
enclosure
Note:
Min. 2” clearance
required between edge
of cutout and inside back
wall of enclosure for gas regulator
36
2 min.
2
7
/
8
C
10
31
3
/
8
Combustible
enclosure
IF YOUR ENCLOSURE
IS COMBUSTIBLE, THEN
THE INSTALLATION OF
AN INSULATED JACKET
MANUFACTURED BY
SOLAIRE INFRARED
GRILLS IS REQUIRED.
YOUR GRILL COMES FROM
THE FACTORY WITH ORIFICES
INSTALLED FOR USE WITH
PROPANE. IF USING NATURAL
GAS, FOLLOW CONVERSION
INSTRUCTIONS ON PAGE 16.
CHECK REGULATOR SETTING
TO ENSURE PROPER GAS
TYPE AS SHOWN IN FIG. 12.
Insulated Jacket Cutout
Dimension C
Model AGBQ-27 17 11/16”
Model AGBQ-27XL 22 9/16”