RAL-KEB02iP USB_DAC Mode Setup Guide Rev. 1.0 01/July/2014 RATOC Systems, Inc. www.ratocsystems.
Index 1. Introduction............................................................ 3 1-1.Features .................................................................................................................. 3 2. System requirements.............................................. 4 2-1. PC running on Windows 8,7,Vista,XP(SP2 or newer) 32/64bits ........... 4 2-2. MacOS X 10.7 or newer ................................................................................... 4 2-3. Stereo Headphone .............
1. Introduction Thank you for purchasing RAL-KEB02iP portable USB_DAC. We are confident that you will enjoy listening Hi-Reso music at anywhere, outdoors and in hime with your PC audio system, Mac Book, iPhone, iPad, iPod and WALKMAN. RAL-KEB02iP receives High-Resolution LPCM format up to 24bit/384kHz from 16bit/44.1kHz and DoP format compatible DSD digital music stream.
2. System requirements 2-1. PC running on Windows 8,7,Vista,XP(SP2 or newer) 32/64bits ●One USB 2.0 HS(480Mbps) enabled Host port. ●Internet access to download USB Audio 2.0 Driver for Windows. ●RAL-KEB02iP USB Audio Class 2.0 Driver installation required. ●User's Guide, Setup Guide and Grade up Guide are able to download from RAL_Audio site.
3. Package contents RAL-KEB02iP package includes: ●RAL-KEB02iP ●USB 2.0 Cable ( USB-A to mini-B ) for USB_DAC mode x1. ●USB-A to micro-B Cable for charging x1. ●USB-A to iPod 30P Dock cable (0.1m) for iPod Compatible mode x1. ●USB-A to Lightning cable (0.1m) for iPod Compatible mode x1. ●Silicon Band to bundle iPod/iPhone with KEB02iP. ** AC adapter (DC +5V/1A) is not included in the package. 4. Front Panel, Rear Panel Layout 4-1. Front Panel (1).
(3). HP level Slide Switch Select Headphone output level. Right position shown in above brings High-Level for high impedance headphones. Left position shown in above brings Low-Level for Low impedance headphones. (4). Analog Filter selection Switch. You can select Analog Filter Curve inside ES9018K2M DAC with this switch. Right position brings Sharp Roll-Off Curve and Left position brings Slow Roll-off Curve. (5). 3.5mm mini Jack. Stereo analog audio output for earphones.
4-2. Rear panel (1). Digital Audio Stream Input for iPod/iPhone/iPad USB-A Connector : Compliant with USB 2.0 Full Speed(12Mbps) Spec. *KEB02ip works as USB-Host but does not provide charging current from this connector. It can provide USB Bus_Power to USB device up to 100mA. *Don’t use this connector at USB_DAC mode. Never connect iPod/iPhone/iPad to this connector when Mode select Switch is set for USB_DAC mode. (2). Digital Audio Stream Input for PC/Mac. USB mini-B Connector : Compliant with USB 2.
(4). Mode Select Slide Switch Use this slide switch to change KEB02iP operation mode. This switch must be set in Power_OFF state, Volume Knob at the front panel must be set at 7'Oclock position. And the Volume Knob must be turned clockwise to enable operation mode being selected by current setting of this switch for iPod Legacy Support mode or USB_DAC mode. - iPod position(Left) : iPod Legacy Support mode. KEB02iP works as an USB Host and iPod/ iPhone/iPad works as an USB Device.
- USB position(Middle or Right) : USB_DAC mode. KEB02iP works as an USB Audio Class 2 Device and High-Speed(480Mbps) Device. Must be set this position before turning Power_ON KEB02iP to connect PC or Mac to USB mini-B port. KEB02iP works with internal battery and does not require USB BUS Power at BT position. Must select BT position to connect Apple Camera Connect Kit, Lightning to USB Camera Adapter or SONY WALKMAN USB Connection canle. KEB02ip works requires USB Bus_Power at BP position.
(5). LEDs (5-1) USB(Green)/ iPod(Red) Lights on Red when succeeded to detect iPod and starts brink to indicate being communicating successfully with iPod. (5-2) PCM(Green)/DSD(Red) Disabled in iPod Legacy support compatible mode. Enabled only in USB_DAC mode. (5-3) EXTP(Green) Indicates External DC+5V Power source or USB Bus_Power(BP mode) is being supplied and KEB02iP is working and charging internal battery with the external power source or USB Bus_power(BP mode). (5-4) Charge.
5. Setting up Mac/MacOS X 5-1. Connecting RAL-KEB02iP to Mac USB port Getting started with setting up your Mac/MacOS X 10.7 or newer. (1) Turn off Power of KEB02iP and select USB_DAC mode. And then turn on power of KEB02iP. (2) Connect RAL-KEB02iP mini-B port to Mac USB port with USB-A to mini-B cable. The cable should be compliant with USB High-Speed(480Mbps) certification. (3) MacOS X will detect and recognize RAL-KEB02iP. (4) Click on the "System Preferences" app on Dock.
5-2. Setting 'Sound Effects' output to Internal Speakers Click on the "Sound Effects" tab to prevent alerts and effect sounds such as "e-mail received notification sound" from being routed to Audio System. Set Play sound effects through 'Internal Speakers'”. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
5-3. Setting RAL-KEB02iP as an Audio Output Click on the "Output" tab and select "RATOC RAL_KEB02iP Audio Out". This selection will route the sound from iTunes or other Audio Applications to your Audio system. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
5-4. Setting up 'Audio MIDI Setup' Application (1) If "Audio Midi Setup" application is not found on Dock, open the Hard Disk icon and open the "Applications" folder. You can find the "Audio Midi Setup" application at the "Utilities" folder. (2) Open the "Audio Midi Setup" application and select "Audio Devices". (3) Click on "Output" tab. Select "RATOC RAL_KEB02iP Audio Out" for the "Default Output" to send the sounds from iTunes or other applications to Audio system.
5-5. Launch and play iTunes or other Music Player application Launch iTunes or other Music Player application. Start it and select Music file. You will listen and enjoy fine and clear sound from your Audio system. To learn more about Music Player application, refer to User Guide or Online Help of the application. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
6. Setting up Windows PC ( Windows 8, 7 ) This chapter describes the driver installation and setting on Windows 7 as an example, these process is almost the same as one on Windows 8, Vista, XP. Getting started with setting up Windows 7 ( 32bit or 64bit ) PC. 6-1. Installation of USB Audio 2.0 Class Driver RAL-KEB02iP requires USB Audio Class 2.0 Driver. You need to install it before using it. If you forgot it or failed to install the driver, RAL-KEB02iP would not be configured as a USB Audio Device.
(7) InstallShield will start and show status. (8) Click 'Install' button at 'Windows Security' dialog box below and continue driver installation. (9) When this message shows up, remove USB Audio Device except RAL-KEB02iP. Only one KEB02iP should be connected at this time. Click "OK","Next","Install","Install" to finish the installation. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
(10) Windows Security dialog box may be shown up again, if so, click 'Install' to continue the installation. (11) Connect RAL-KEB02iP to your PC when the dialog box below is shown up. Click 'OK' after the connection is completed. (12) InstallShield Wizard will check system, prepare and start the installation. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
(13) InstallShield Wizard will complete. Click "Finish". (11) Open Device Manager Window and check "RATOC Systems, Inc. Check 'USB 2.0 Audio Devices RAL-KEB02iP' is shown up. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
-2. Uninstall RAL-KEB02iP Device Driver If you failed in RAL-KEB02iP Driver installation or desire to remove it from your Windows PC, uninstall it and re-install again. Follow the instructions below. (1) Open 'Control Panel' and select 'Programs and Features' icon. (2) Select and click 'REX-KEB02iP Driver'. (3) InstallShield will start and show dialog box below. Just in case, make sure you will start to uninstall. And then click 'Yes.' RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
(4) Click "Finish" at InstallShield Window below. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
7. Grade up setting for Windows This chapter describes how to improve sound quality and tune up your PC to listen high fidelity and pure sound. Before installation of Music Player application or additional drivers: - Check Compatibility and Combination of Sound Drivers and Applications. And select most suitable one for your PC/Mac Audio system. You also need some setting at Device Manager Window to use the application or add-on drivers. - Set disable to route "System Sound" to your Audio system.
7-1.Listen HD Music with Direct Sound and Kernel Mixer (1) Double click "RAL-KEB02iP Audio" at "Playback" tab. Click "Properties" button. You can change icon and device name as you like. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
(2) Click "Advanced" tab and select Sampling Rate/bit rate corresponding to property of music files you like at "Default Format" box. Note) 24bit/88.2kHz, 24bit/176.4kHz, 24bit/352.8kHz and 24bit/384kHz are not shown up at the list box. This is the known issue of Windows 7/Vista Direct Sound Driver. RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
7-2.Using WASAPI mode, skip Kernel Mixer Windows 8, 7 and Vista(SP1 or newer) includes this function. Once enabled, Windows Kernel Mixer is bypassed and Audio application can pass music data to Audio drivers directly. ** iTunes does not work with WASAPI setting on 64bit Windows 8, 7, Vista. (1) Click "Start" and launch "Control Panel". (2) Double click "Sound". (3) Double click "RAL-KEB02iP Audio" at "Playback" tab. And click "Properties" button.
8. Specifications Name DSD and High-Reso PCM ready portable USB DAC Model Number RAL-KEB02iP Terminals USB mini-B for USB_DAC mode. USB-A for iPod Compatible mode. Supported PC Windows 8, 7, Vista, XP, Mac OS X 10.7 or later. *Windows 64 bit versions are supported. Inputs Supported Audio USB_DAC mode USB Audio Class 2.0 ( 480Mbps required ) Input Format (Hi-Speed mode is required) DSD 5.6448/2.8224MHz ( DoP standard-compliant). L-PCM24bit/16bit,384kHz/354.8kHz/192kHz /176.4kHz/96kHz/88.
RAL-KEB02iP (USB_DAC Mode) User's Guide Rev 1.
