Aqua Attachments Owner’s Manual www.ravesports.
Table of Contents Introduction .........................................................................................2 Safety rules and information.............................................................3 Inflation valve operation ...................................................................5 Assembling your Slide .........................................................................6 Assembling your Log ........................................................................
Introduction Thank you for purchasing a RAVE Sports Aqua Attachment. Water sports can be safe and fun for all levels of enthusiasts. This Owner’s Manual is presented to enhance your enjoyment of the sport. It is intended to alert you to some of the potentially dangerous conditions that can arise in all water sports. Please take a few minutes to read this manual before assembling and using the product.
Safety Rules and Information • Read and understand all of the information contained in this owner’s manual before assembling and using your product. • Make sure that everyone who uses the product is provided with and understands these safety rules and information. • The Aqua Attachments are designed to be used only while secured to the Classic Aqua Jump® or the Aqua Jump Eclipse in large bodies of water with depths of at least 10 feet of water.
• Never use the product while tired or fatigued. Use extreme caution while swimming between the shore and the product. Do not attempt to swim this distance if you are tired or fatigued. • Always inspect the areas around and under the product before each use to ensure the water is deep enough and free of all rocks, logs, sand bars, and underwater obstructions and that the product is a safe distance from above water hard objects. Ask about local water conditions before using the product in unfamiliar water.
Inflating any RAVE Aqua Attachment We highly recommend using the RAVE High Speed Inflator/Deflator. It will provide rapid inflation/deflation and will achieve optimum air pressure in your RAVE product. (Part # 01083 not included). OPEN CLOSE To lock open valve, depress the stem and rotate ¼ turn clockwise. To close valve, depress the stem and rotate ¼ turn counter-clockwise. The valve stem should be in the depressed position while inflating. Replace cap on valve after inflation to ensure air tight seal.
! CAUTION DO NOT USE AN AIR COMPRESSOR TO INFLATE ANY AQUA ATTACHMENT. USE OF AN AIR COMPRESSOR MAY CAUSE OVERINFLATION, WHICH CAN DAMAGE OR RUPTURE SEAMS. IMPORTANT: It is normal for the air pressure within air filled tubes to fluctuate depending on air and water temperatures. It may be necessary to increase or decrease the air pressure in your product accordingly. To avoid damage on extremely hot days it may be necessary to check and release the air pressure from your product throughout the day.
inflated. Check alignment of tubes and fit of cover periodically during inflation. If tubes are not aligned properly, release some air and move tubes to align. When properly inflated and assembled, the tubes on the underside of the Aqua Slide should be level with each other and the cover should be straight and taught as shown. Connecting to your Water Trampoline To attach Slide to Classic Aqua Jump™ (with steel frame), see p. 7 To attach Slide to Aqua Jump™ Eclipse (without steel frame), see p.
buckle and pull tight keeping the buckle just below the trampoline frame. NOTE: Pad removed in photo for visual clarity. Feed the short strap over the frame, and through the buckle on the side of the Slide cover. Make sure that the strap is tight up against the frame. Step 4 Loosely fasten strap through buckle and repeat for other side of Slide. Center Slide nicely between the straps then tighten both straps.
Step 3 Determine the preferred location for the Slide on the Aqua Jump Eclipse. Make sure the pad is oriented so the one section with slots is oriented to match the preferred Slide location on the Aqua Jump Eclipse tube. Step 4 Starting from the inside of the tube, feed both ends of one buckle strap through the Δ-ring closest to the corner of the tube on the section you want the Slide to be attached. Wrap the long strap around the outside of the inflated tube and fasten to the buckle on the inside.
Step 8 Feed the short strap through the buckle on the side of the Slide. Loosely fasten. Repeat for other side of Slide. Center Slide nicely between the straps then tighten both straps. NOTE: Check the Slide attachment straps periodically to ensure they are tightly fastened and the Slide is secure and stable.
Attaching the Aqua Slide small to Aqua Deck™ Follow steps 1 and 2 for inflating your slide from page 6 Step 3 The Slide will be attached on the corner of your Aqua Deck water trampoline. Attach the product while both the Aqua Deck and Slide are in shallow water. Fasten the straps on each side of the corner of the Aqua Deck tube following the steps outlined for the Aqua Jump Classic trampoline (p. 7). Step 5 Make sure the straps are tight and the Slide is positioned over the corner of the Aqua Deck.
Step 4 Feed the end of the long strap down between the jump mat and the tube at the point nearest the tube corner. Bring the free end of the strap around the tube and loosely fasten in the buckle. Step 5 Wrap the short strap under itself and through the jump mat lacing as shown. Now feed the strap through the buckle on the slide and fasten loosely. Repeat for other side of Slide. Center Slide nicely between the straps then tighten both straps.
Step 6 Make sure the straps are tight and the Aqua Slide is positioned overhanging the tube of the Bongo. The Slide is now ready to use! Please read and follow all safety instructions before enjoying your slide. AQUA LOG ASSEMBLY INSTRUCTIONS Aqua Log™ (NOTE: Small and Large Log models are assembled and attached in the same manner to all RAVE water trampoline products.) Step 1 Lay the Aqua Log on a flat surface. Make sure there are no sharp objects under the product that might puncture the tube.
Center the Log on one side of the Aqua Jump. DO NOT PLACE ON THE SIDE WHERE THE VALVE IS LOCATED. Wrap the straps around the tube and buckle tightly. Attaching the Aqua Log to a Bongo Run the bottom two straps under the Bongo and the top two straps over the top of the Bongo. Note: the top two straps should run through the semi-circular cut-outs on the lacing apron as shown. When properly installed, there will be two cutouts between the straps.
AQUA LAUNCH ASSEMBLY INSTRUCTIONS Aqua Launch™ (NOTE: This product assembles and attaches in the same manner for all RAVE water trampoline products.) Step 1 Lay the Aqua Launch on a flat surface. Make sure there are no sharp objects under the product that might puncture the tube. Step 2 See inflation and valve operation on p. 5. Inflate the Launch until the tip of the inflation gauge strap is just touching the ground. DO NOT FILL THE LAUNCH TO FULL CAPACITY.
the top side of the water trampoline. Bring the bottom of the Launch straps up underneath the tube and connect to the apron straps. Ensure all three straps are uniformly spaced apart and are parallel to each other. Tighten securely. NOTE: The outside bottom straps have a metal ring attached to them. These rings are only used when attaching the Aqua Launch to an Activity Island.
SLIDEWALK ASSEMBLY INSTRUCTIONS Slidewalk™ (NOTE: This product assembles and attaches in the same manner for all RAVE water trampoline products.) Step 1 Lay the Slidewalk on a flat surface. Make sure there are no sharp objects under the product that might puncture the tube. Spread out the cover, with inside facing up, on a flat surface free from debris and sharp objects. Extend straps away from cover and place tubes in cover.
Securely fasten the two short straps at each end of the cover to the buckles on the tubes. Flip the Slidewalk over and carry to the water. Step 3 Use the long straps provided to attach the Slidewalk to the water trampolines. Feed one end of each strap through the metal ring on the end of the Slidewalk cover. Wrap the strap around the water trampoline tube and buckle securely. Repeat for all straps. Properly attached, the Slidewalk should be pulled up tight against the tube of the water trampoline.
Cleaning and Storage • When the inflatable product is not being used, store it in a covered, shaded area. This will help protect it against ultraviolet (UV) rays and extend the life of the product. • Clean the inflatable completely with a mild soap and fresh water. NEVER USE PETROLEUM BASED PRODUCTS OR SOLVENTS FOR CLEANING. NEVER USE A POWER WASHER SINCE THE HIGH PRESSURE WATER JET WILL DAMAGE THE TUBE BEYOND REPAIR. • Product should be completely dry and remain dry while stored.
Repairs For large holes, tears or seam failures, contact RAVE Sports at 1-800659-0790. Additional repair patches can be found online at www.ravesports.com. For minor holes or tears: • Inflate the product and locate the leak by spraying the tube with mild soapy water. • Determine the hole size and cut a patch 1-2 inches wider than the diameter of the hole. Make sure all corners of the patch are rounded. • Deflate the product and clean the patch and area around the hole with rubbing alcohol.
This page intentionally left blank.
This page intentionally left blank.
www.ravesports.com RAVE Sports A Revel Match, LLC Company 3325 Labore Road Saint Paul, Minn.