INSTALLATION AND OPERATION INSTRUCTIONS FOR STRATUS 100-44 XT STRATUS 125-44 XT SAFETY INFORMATION WARNING If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
TABLE OF CONTENTS Please read and carefully follow all of the instruction found in this manual. Please pay special attention to the safety instructions provided in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Rayburn product. IMPORTANT INSTRUCTIONS....................................................................................................................................3 UNPACKING AND TESTING APPLIANCE ...............
IMPORTANT INSTRUCTIONS 1. Read all instructions before installing or using this heater. 2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front of the heater; keep them away from sides and rear as well. 3. Always switch off the heater at the mains supply when not in use. 4. Do not operate the fireplace if it has a damaged cord or plug, after it has malfunctioned, or if the unit has been dropped or damaged in anyway. 5.
Cautions ·Always install the heater in accordance with this guide. If in doubt obtain expert advice. ·Always make sure the electrical socket is accessible and located adjacent to, but not above the heater. Do’s ·Always disconnect the heater from the electrical supply before moving it, or carrying out cleaning, maintenance. ·Always make sure the heater is firmly secured to prevent it from being tipped over.
UNPACKING AND TESTING APPLIANCE Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 230V electrical socket. Test all aspects of its operation (manual switches, remote and heater) to make sure all components operate correctly. As with most electronic devices, your new electric fireplace has been designed to operate at temperatures between 5℃ and 35℃.
STRATUS 100-44 XT Description Voltage Watts NO HEATER MOTOR HEATER Appliance Width Appliance Height Appliance Depth Gross Weight Plug Location Cord Length Rough Wall Opening Size KW This appliance has been tested in accordance with the EN 603351:2012 + A11:2014 + A13:2017,EN 60335-2-30:2009 + A11:2012, EN 62233:2008. If you need assistance during installation, please contact your local dealer. Built-in Appliance 230V AC 50Hz 1900W Max 28.6W 19W 98.1 cm 75 cm 32.2 cm 53kg Left side 180 cm 101.6 cm× 76.
STRATUS 125-44 XT Model Number Voltage Watts NO HEATER MOTOR HEATER Appliance Width Appliance Height Appliance Depth Gross Weight Plug Location Cord Length Rough Wall Opening Size KW Built-in Appliance 230V AC 50Hz 1900W Max 33.6W 19W 123.5 cm 75 cm 32.2 cm 66.1kg Left side 180 cm 127 cm ×76.2 cm 1.9 This appliance has been tested in accordance with the EN 603351:2012 + A11:2014 + A13:2017,EN 60335-2-30:2009 + A11:2012, EN 62233:2008.
SAFETY DRILL SCREW AREA There is a safety drill screw area as show below. Please make sure that the fix screws are in this area.
INSTALLATION NOTE: Due to the many different materials used to build walls, it is highly recommended that you consult your local builder before you install this appliance on a wall. The STRATUS XT Models are designed to be either bui lt-in or wall-mounted depending on preference. These units allow for the finishing material (drywall, stone, tile, etc.) to be built right down to the glass edge.
2. Remove the framing plates from the unit framing plate 3.
4. Bend up the framing plates. 5. Put the unit into the opening.
6. Drive the mounting screws into the framing plates on the unit and the wall studs. framing plate 7. After checking that the fireplace operates properly, cover the glass panel with protective plastic bag and install plywood or drywall. IMPORTANT NOTE: IF YOU WANT TO USE THE SUPPLIED SURROUND the thickness of the wall finish can only be 1”.
8. Decorate the plywood or drywall with glazed tile, wallpaper, etc. Fireplace 9. Put back the trim that you’ve removed from the unit at STEP 1.
MEDIA OPTIONS The STRATUS XT series are shipped with 11-PIECE-LOG, AMBER GLASS and VERMICULITE. 1 2 3 1. Vermiculite 2. Amber glass 3.
FIRE GLASS MEDIA-LOG INSTALLATION 1. Take off the front clear glass. There is a bracket that holds the front glass as shows below. Unscrew the screw to take off the bracket. Turn around the bracket and insert it into the gap to hook and pull out the glass. 2. Install the fire glass media. Pour the fire glass media into the tray as shows below. Feel free to use any combination of fire glass media that you find most appealing. IMPORTANT: GLASS IS VERY SHARP - PLEASE WEAR PROTECTIVE GLOVES 3.
OPERATION The fireplace can be operated either by the switches located on the left bottom of the fireplace unit or by supplied remote control. Plug the fireplace into a13 Amp wall socket. MANUAL OPERATION 1、Press key . Press for the first time, heater work at 1900W, indicator Press for the second time, heater work at 950W，indicator lights red. lights blue. Press for the third time, the heating element turns off, indicator extinguishes.
REMOTE CONTROL OPERATION 1 2 3 、 Press the remote control’s key“ 1 ”, its screen turns on, the flame ignites and the flame icon appears on the LCD screen of the remote control. Week, time (24h system), and temperature setting are displayed normally. Press it again, the screen of the remote control will turn off; 、 Key“ 2 ”, flame and charcoal control switch. In case of ON, press once, the flame and the charcoal bed go out, the LCD screen does not display the LCD screen displays . .
7、Press the heating key“ .” Press for the first time ,the heating elements work at 1900W, the LCD screen displays , the indicator on the machine lights red. Press a second time , the heating elements work at 950W, the LCD screen displays , the indicator on the machine lights blue. Press a third time and the heating elements turn off, the LCD screen does not display the function icon, the indicator on the machine goes off.
for Tuesday. Press for the 7th time and it displays . Press for the 8th time and it exits and recovers to the current week day; 11、Press“ displays .” Press for the first time and the timing function turns on, the LCD screen , the machine’s indicator on the LCD screen lights green. Press again to turn off, icon goes off. After the timing function is turned on, it works according the parameter settings.
CARE AND MAINTENANCE 1. Switch off and unplug from the power supply before cleaning. 2. Using a soft, moist cloth, with or without a mild soap solution, carefully clean the exterior surface of the products. CAUTION: Allow the product to completely cool before handling or cleaning it. 3. Do not allow water or other liquids to run into the interior of the product, as this could create a fire and/or electrical hazard. 4.
REPLACEMENT PARTS This list contains replacement parts NO PART NUMBER STRATUS 100-44 XT 1 DESCRIPTION QTY BLOWER AND HEATER ASSEMBLY(FRT60-420) 1 FIREPLACE BOX 1 STRATUS 125-44 XT 602032B 2 3 10104002 SWITCH 1 4 601035 CONTROL PANEL 1 5 601095F CIRCUIT BOARD 1 6 10101221C FLAME MOTOR 2 FLICKER ASSEMBLY 2 7 3109503C 3057503C 8 601136B LED STRIP 9 10203015 ADJUSTABLE FOOT 14 FLAME EFFECT GLASS( WITH BLACK PLASTIC) 1 10 10701263 10701265 11 3057012 GLASS BRACKET LH
EXPLODED VIEW 22
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Dim or no flame Flame LED’s are burnt out Inspect the LED’s and replace them if necessary. Ember bed is not Ember LED’s are burnt out Inspect the ember bed LED’s and glowing or dimming replace them if necessary. Appliance turns off and Appliance has over heated and Turn off the main switch, allow will not turn on safety device has caused the appliance to cool for10 minutes, then thermal switch to disconnect turn it on.
SERVICE HISTORY This heater must be serviced annually depending on usage.
Warranty FREESTANDING ELECTRIC – 2 YEAR EXTENDED WARRANTY If you have purchased your stove from an authorised stockist within our Retailer Network, then automatically your product will carry a standard 1 year warranty. The 1 year warranty can be further extended to a total warranty period of 2 years by registering your Stove within 60 days of the purchase date or installation date whichever is shortest. Accordingly, the start date for the warranty period is the date of purchase.
The Extended Warranty does not cover: a) In normal usage the paint finish of your Stove may change colour slightly. As these circumstances are considered normal, they are not covered by the warranty. b) Enamelled components where these parts are subjected to abnormally high temperatures, chemical abrasion or thermal shocks, resulting in chipping, cracking, bubbling or discolouration and crazing of the enamelled finish.
