DISH Network MIM (Multi-satellite Interface Multi-switch) Installation and User Manual 81348-1
Raymarine MIM Serial Number This serial number will be required for all troubleshooting or service calls made regarding this product.
CONTENTS INTRODUCTION 1 INSTALL THE MIM 2 CONNECT THE CABLES TO THE MIM 4 SET THE DIP SWITCHES FOR CONNECTED MIMS 9 SELECT THE MASTER CONTROL FUNCTION 10 SETUP THE ANTENNA CONTROL UNIT 11 SETUP THE RECEIVER AND TEST “CHECK SWITCH” 13
INTRODUCTION 1 Introduction Introduction to Raymarine Dish Network Multi-sat Interface Multi-switch The Raymarine’s Multi-sat Interface Multi-switch (MIM) utilizes a leading-edge technology which replaces the Dish Network DP-34 multi-switch. The user oriented design of the MIM offers Dish Network subscribers access to their favorite high-definition (HD) programming and switches automatically between Dish Network 110°W, 119°W, and 129°W satellites or alternatively between satellites 61.
2 Dish Network MIM - Installation and User Manual Install the MIM INSTALL THE MIM Power Requirements You will need to wire the Raymarine STV series system differently than specified in STV series manual. These instructions require additional installation steps. The following instructions and configuration diagram will explain how to modify your system for MIM use. MIM Dimensions For your own safety, make sure to disconnect power from all wired components (i.e.
4 Dish Network MIM - Installation and User Manual CONNECT THE CABLES TO THE MIM Connect the cables to the MIM Single Receiver Installation 1. Connect the RF cable from the “RF1” connector on the antenna to the “ANT. RF” connector on the rear panel of Antenna Control Unit (ACU). 2. Connect the RF cable from the “RECEIVER” connector on the rear panel of ACU to the “RF INPUT-RF1” connector on the MIM. 3. Connect the RF cable from the “RF2” connector on the antenna to the “RF INPUT-RF2” connector on the MIM.
6 Dish Network MIM - Installation and User Manual CONNECT THE CABLES TO THE MIM Multi-Receivers (up to 4) Installation Dual Tuner Receiver Installation Instructions 1. Connect the RF cable from the “RF1” connector on the antenna to the “ANT.RF” connector on the rear panel of Antenna Control Unit (ACU). 1. Connect the RF cable from any “TO RECEIVER SATELLITE IN” on the rear of MIM to the “Satellite 1” on the rear panel of the receiver. 2.
Dish Network MIM - Installation and User Manual SET THE DIP SWITCHES FOR CONNECTED MIMS 9 Multi-Receivers (more than 4) Installation 1. You must have two or more MIM units to start with this installation. 2. Connect the RF cable from the “RF1” connector on the antenna to the “ANT.RF” connector on the rear panel of Antenna Control Unit (ACU). 3. Connect the RF cable from the “RECEIVER” connector on the rear panel of ACU to the “RF INPUT-RF1” connector on the first MIM. 12.
10 Dish Network MIM - Installation and User Manual Select the Master Control Function for Connected Receivers Raymarine’s MIM allows you to select which receiver connected to the MIM will be the “Master” receiver by pressing the “Select” button on the front panel of the MIM. SETUP THE ANTENNA CONTROL UNIT Setup the Antenna Control Unit In order to configure the correct set of satellites for MIM use, follow the instructions below on the ACU. ACU setup should be Triple Sat as follows: 1.
12 Dish Network MIM - Installation and User Manual 6. Set satellite C Press PREV to show previous satellite name. Press SELECT to set chosen satellite to SAT C. Press NEXT to show next satellite name. 7. Press YES to save selections. Press NO to cancel and return to main setup mode. SETUP THE ANTENNA CONTROL UNIT 13 Setup the Receiver Setup and Test “Check Switch” After all cables are connected completely, turn on the power for the ACU.
14 Dish Network MIM - Installation and User Manual 2. Select “Check Switch” button and select “Test”. Be sure that “SuperDISH” and “Alternate” are NOT checked. 3. Wait until the message “Currently doing test #3 of 3” appears. This indicates the test is completely done. If the message is different, check your connections again. Make sure the receiver you are running the “Check Switch” on is designated as the Master receiver. With dual tuner receivers, wait for the “Satellite Input2” test to be completed.
16 Dish Network MIM - Installation and User Manual 6. At this point, the receiver begins the procedure to download the program guide information. When the message below displays, follow the instructions and do not disturb the receiver until the TV displays video. 7. If you have other receivers connected to the MIM, set each receiver as a Master (Refer to Page 10) and repeat these procedures from 1 to 6.
www.raymarine.