Basic operation instructions English (en-US) Date: 03-2017 Document number: 81369-2 © 2017 Raymarine UK Limited
Important information about this document This document provides an introduction to using your Raymarine multifunction display, covering only basic operations. To obtain the complete “LightHouse 3 Advanced operations” document, visit the Raymarine website. The document is available in 2 different formats: 1. Free download (PDF format) 2. Purchase a printed manual (paperback book format) www.raymarine.
Contents Chapter 1 Important information ................................................. 8 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 2 Set up ........................................................................ 9 2.1 Getting started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.11 Sidebar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 3.12 Data overlays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 3.13 Editing the split ratio of a Splitscreen app page. . . . . . . . . . . . . . . . . . . . . . . . . 30 Chapter 4 Chart app............................................................
Customizing existing Data pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Chapter 8 Camera app ............................................................... 52 8.1 Camera app overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Camera app controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1: Important information Warning: Ensure safe navigation This product is intended only as an aid to navigation and must never be used in preference to sound navigational judgment. Only official government charts and notices to mariners contain all the current information needed for safe navigation, and the captain is responsible for their prudent use.
Chapter 2: Set up 2.1 Getting started Powering on the display When power is available to the MFD but the MFD is switched off, the Power symbol will be illuminated. To power on the display: 1. Swipe your finger from left to right across the Power button swipe area. The MFD will power up. Powering off the display 1. Swipe your finger from left to right across the Power button swipe area. The Shortcuts menu is displayed. 2. Press and hold the Power symbol until the screen switches off.
Switching on and off at the breaker If you wish to ensure that the MFD is not consuming any power then it must be switched off at the breaker or have the power cable unplugged. When the breaker is switched back on, or the cable is reconnected, the MFD will resume in the same power state that it was in when it was switched off. First power up Data master selection Networks containing more than 1 MFD must have a designated Data master.
First power up Limitation on Use acknowledgement After you have completed the Startup wizard the Limitation on Use (LoU) disclaimer is displayed. You must read and agree to the terms in order to use your MFD. Selecting OK means you have accepted the terms of use. Data sources menu When a system includes multiple sources of a data type, such as depth data, the system will choose the most appropriate source for the data. If you prefer, you can manually select your own data source.
Networked MFDs will automatically be updated to use the Data sources selected on your Data master MFD. Data source types Settings tab Description Depth Enables you to choose a source of data for Depth readings. Speed through water Enables you to choose a source of data for Speed readings. Heading Enables you to choose a source of data for Heading data. GPS Enables you to choose a source of data for GPS data.
Configuring Transducer settings For systems set up with Sonar, you should configure your transducer settings. 1. Select Transducer from the Sonar app’s Settings menu: Menu > Settings > Transducer 2. Select how you want your depth to appear: i. Below transducer (default) — No offset required ii. Below keel — Enter the distance between the transducer face and the bottom of the Keel. iii. Below waterline —Enter the distance between the bottom of your Keel and the waterline. 3.
2.2 Inserting a MicroSD card 1. Pull back the microSD card reader cover as shown above. 2. Insert you microSD card with the contacts facing down. 3. Close the cover and ensure it is seated correctly. Memory card compatibility MicroSD memory cards can be used to back up / archive data (e.g. Waypoints, Routes and Tracks). Once data is backed up to a memory card, old data can be deleted from the system. The archived data can be retrieved at any time.
2.3 Shortcuts The Shortcuts menu can be accessed by swiping left to right across the Power button swipe area. The following shortcuts are available: • Take Screenshot • Activate Touchlock • Stop Radar transmitting • Power off • Adjust Brightness Adjusting brightness LCD brightness can be adjusted from the Shortcuts menu. 1. Swipe your finger from left to right across the Power button swipe area. The Shortcuts menu is displayed 2.
Activating touchlock In rough weather conditions precipitation may lead to erroneous touches being detected by the touchscreen. In these conditions you can use touchlock to prevent this. 1. Select Activate touchlock from the Shortcuts menu. With touchlock activated the touchscreen will be disabled. To re-enable the touchscreen, swipe from left to right across the Power button swipe area. Radar standby You can place a transmitting Radar in Standby from the Shortcuts menu. 1.
Updating software using a memory card 1. Check the software version of your product. The software version can be found on the Getting started tab: (Homescreen > Settings > Getting started). 2. Check the latest available software on the Raymarine website: (www.raymarine.com > Support > Software Updates). 3. Download the software package. 4. Copy the files to MicroSD card. 5. Insert the MicroSD card into the card reader slot on your MFD. 6.
Chapter 3: Homescreen 3.1 Accepting the Limitations on Use After your MFD has powered up the Homescreen is displayed. 1. Before using the MFD you must accept the Limitations on Use (LoU) disclaimer. To view the full LoU Disclaimer, select ‘more details’. The LoU acknowledgment is displayed each time the display is powered on and for each new user profile. The full LoU text can be accessed at any time from the Getting started tab: Homescreen > Settings > Getting started > View terms of use.
3.2 Homescreen overview All settings and apps can be accessed from the Homescreen. 1. GNSS position/fix details — Select the area to view fix accuracy and access GNSS settings. 2. Profile — Select the area to change the profile in use or to create, edit or delete profiles. 3. External devices and system time — Select this area to adjust the UTC time offset. 4. App page icons — Select an icon to open the relevant application page.
You can Customize, Rename or Delete app pages from the Popover options. 2. Select Customize from the Popover options to change page layout and apps used. To Create a new page press and hold on a blank space on the Homescreen. 3. Select the Layout: option to change the page layout. 4. Select the icons for the Apps that you want to be displayed on the page. 5. Select Next and give the page a memorable name. 6. Select Save. The page is saved and the new App page icon will be shown on the Homescreen. 3.
Selecting the Plus (+) icon will create a new profile based on the profile that is currently in use. MFD settings changes are unique to the profile in use and are retained the next time the profile is used. The distance and time that a profile has been active is displayed for each profile. Profile names and icons can be customized. You can also reset the distance and time for each profile. A Guest profile is available for temporary users. Setting changes to the Guest profile are not retained.
Selecting Waypoints, Routes or Tracks will take you to the relevant list where you can manage and customize your data. Selecting Trip will display the trip counters. Selecting Reset man. trip will reset the Trip counter to zero. Selecting Files opens a file browser. Selecting Import/export allows you to back up or restore User data using external storage. For further information on Waypoints, Routes and Tracks please refer to: . 3.
Tab Options • Configure batteries. • Configure fuel tanks. Units • Configure preferred units of measurement. • Configure Bearing mode. • Configure variation. • Configure GNSS system datum. This display • Assign a Homescreen page or app to start on power up. • Select save location for screenshots. • Pair/unpair with a RMK external keypads. • Pair with a wireless Quantum Radar scanner. • Perform a Settings or Factory reset. Network • View list of networked MFDs. • Assign a MFD Data master.
The MOB feature requires your vessel to have a valid position fix from a GNSS receiver. Dead reckoning mode also requires Heading and Speed data. When you activate the MOB alarm: • an audible alarm is sounded which is repeated every 30 seconds until the alarm is cancelled. • a MOB Databar providing Bearing and range from MOB, and elapsed time since MOB was initiated, is placed along the top of the screen. The Databar persists across apps and the Homescreen, and remains until the MOB alarm is cancelled.
3.8 Alarms The Alarm manager can be accessed from the Homescreen. Example: Active alarms list Alarms are raised by system functions, and also external equipment connected to your display. When an Alarm is triggered all networked MFDs will display audible and visual warnings. The onscreen warning provides details of why the alarm has been triggered.
3.9 Satellite navigation / positioning GNSS Status Your vessel’s GNSS position is provided in the top left corner of the Homescreen. You can access fix accuracy and settings by selecting the area. If latitude and longitude is displayed on the Homescreen then you have a valid position fix. If the text turns red then your fix accuracy is low. The sky view on the left side of the page shows the position of navigation satellites and the constellation they belong to.
GNSS Settings The settings for your GNSS receiver (internal or external) can be accessed from the Satellites menu: Homescreen > GNSS popover > Satellites > Settings. From the GNSS Settings tab you can: • activate and deactivate use of Differential positioning (SBAS) • set the COG/SOG filter according to your vessel’s oscillation, which provides more stable COG and SOG readings • enable and disable your MFD’s internal GNSS receiver.
3.10 External devices You can view the status of peripheral devices connected to your MFD using the Status area, located at the top right of the Homescreen. You can also connect and disconnect from some devices using the Status area popover menu. Status area icons The following devices’ status can be reported in the Status area: • AIS • Radar • Sonar module/Transducer Popover menu options From the Options popover you can: • Switch your AIS transceiver between transmitting and silent mode.
3.11 Sidebar The Sidebar is available in all apps and provides quick access to system data. By default the Sidebar is set up to display navigation data. The Sidebar is displayed automatically in the Chart app when a Goto or follow is initiated. It can also be displayed at anytime by sliding your finger from left to right from the left edge of the screen. Swiping right to left will hide the Sidebar.
Data overlays can be customized from: Menu > Settings > Page Settings > Edit data overlays. In edit mode, drag the data overlay to the desired location, then pressing and holding on a Data overlay displays the Popover menu where you can Edit, Move, Resize or Delete the Data overlay Select Add to add another overlay or Done to exit edit mode. 3.13 Editing the split ratio of a Splitscreen app page With a Splitscreen app page displayed: 1.
Chapter 4: Chart app 4.1 Chart app overview The Chart app displays a representation of your vessel in relation to land masses and other charted objects, which enables you to plan and navigate to your desired destination. The Chart app requires a GNSS position fix in order to display your vessel at the correct location on a world map. For each instance of the Chart app you can select which electronic cartography that you want to use, the selection will persist over a power cycle.
5 Route You can plan your route in advance by creating a Route using Waypoints to mark each route leg. 6 Destination waypoint During a goto, this is the current destination waypoint. 7 Heading line If Heading data is available then a Heading vector for your vessel can be displayed. 8 COG line If COG data is available then you can display a COG vector for your vessel. 9 Tide indicator Provides Set and drift indicators. Requires the following data; COG, Heading, SOG, and STW (Speed Through Water)..
Chart ranging and panning You can change the range displayed in the Chart app using the onscreen Range controls or by using the pinch-to-zoom multi-touch gesture. You can pan the chart area by swiping your finger across the chart. Selecting a chart card You can use electronic charts from supported vendors to enhance the level of detail provided by the Chart app. The electronic chart card must be inserted into the MFDs MicroSD card reader (or the card reader of an MFD on the same network).
DETAILED This is the default chart mode. Full menu options are available and any changes made are saved to the user profile in use. FISHING Fishing mode optimizes the Chart app for Fishing and displays more detailed contour lines, if supported by your selected cartography. Full menu options are available and any changes made are saved to the user profile in use. SIMPLE In Simple mode chart detail is suppressed to provide a clearer, simpler view for navigation. Only navigation menu options are available.
• show/hide range rings • show/hide Tide and Wind graphics Layers Aerial, AIS, Radar and Range rings can be overlaid on the Chart app. The Layers tab from the Chart app Settings menu: Menu > Settings > Layers provides controls for Chart layers.
View and motion The view and motion tab allows you to control how the chart is displayed in relation to your vessel. Chart motion Chart motion controls how the chart and boat are drawn to keep the boat onscreen as you move. Chart orientation The orientation of the chart affects the alignment of the chart relative to your vessel, route or North. Boat position Adjust the boat position to allow more or less ‘look ahead’ space in front of your boat.
The location you select will become the first waypoint for your route. 3. Select further locations to create Route legs. 4. When your Route is complete, select Finish route build 5. Select Exit return to normal operation. Recording a Track You can record your vessel’s journey using Tracks. 1. Select and hold on your boat icon. 2. Select Start track from the popover menu. Your vessel’s journey will now be recorded. 3.
Chapter 5: Sonar app 5.1 Sonar app overview The Sonar app displays a visualization of the echoes received from a Sonar module and transducer. The Sonar app is compatible with Traditional, CHIRP, DownVision™, SideVision™ and RealVision™ 3D sonar modules and transducers. The Sonar app builds an underwater view of bottom structure and targets in the water column. Multiple Sonar modules can be connected at the same time.
Icon Description Action Waypoint / MOB Place waypoint / activate Man overboard (MOB) alarm Image adjustment Displays onscreen sensitivity / image adjustment controls Resume scrolling When the Sonar app is paused, for Waypoint placement, you can recommence scrolling by selecting the Resume scrolling button. Range/Zoom In When Auto range is enabled, pressing the plus icon activates Zoom mode, subsequent presses will increase the Zoom factor.
• One finger swipe rotates the image. • Two finger swipe pans the image around the screen. • Pinch-to-zoom changes the magnification of the image. • The Range control determines how far the sonar will ping. Opening the Sonar app The Sonar app is opened by selecting a page icon from the Homescreen that includes a Sonar app. Pre-requisites: 1. Ensure your Sonar module is compatible (check the latest details available on the Raymarine website).
Select OK and then choose the Sonar channel you want to use from the list: Sonar on and pinging If your Sonar app has already been set up then when the Sonar app is opened the Sonar image will be displayed and start scrolling. No sonar source available If the ’No sonar source available’ warning is displayed then either: • your sonar module is still powering up. • your MFD cannot establish a connection with your external Sonar module • your Internal Sonar module has no transducer connected.
Check your external sonar module’s network and power connection, check your MFD’s network or transducer connection ensuring the connections and cabling is correct and free from damage, then power cycle your system. If the Sonar module is still not found then refer to your equipment’s installation documentation for further troubleshooting information. No transducer connected If the ‘No transducer connected’ warning is displayed then your Sonar module cannot connect to your transducer.
RealVision™ 3D SideVision™ DownVision™ High CHIRP / High Frequency Medium CHIRP / Medium Frequency Low CHIRP / Low Frequency Selecting a Sonar channel The first time you open a new Sonar app page you will be requested to select a channel, subsequently you can change the sonar channel by selecting a channel icon from the Sonar app menu. 1. Select a relevant channel icon from the Menu. 2. Alternatively select All channels from the Menu and then choose your desired sonar module and channel.
Chapter 6: Radar app 6.1 Radar app overview The Radar app displays a visualization of the echoes received from a connected Radar scanner. The Radar app is an aid used to help enhance collision and situational awareness by enabling target’s distance and speed to be tracked in relation to your vessel. Up to 2 Radar scanners can be connected at the same time. However, only 1 Radar in a system can be a Quantum™ Radar.
Icon Description Action Image adjustment Displays onscreen sensitivity / image adjustment controls Power Off Powers down the current Radar scanner Power On Powers up the selected Radar scanner Transmit Start Radar transmission Range In Decreases the distance displayed onscreen (minimum range: 1/16nm). Range Out Increases the distance displayed onscreen (up to your Radar scanners maximum range).
Off/Not Connected If the ‘Off/Not Connected’ message is displayed then: • your Radar scanner may be powered down, or • your MFD cannot establish a connection with your Radar scanner Select On to power up your Radar. If the ‘Radar not found’ message is displayed then a connection could not be established, ensure that network and power connections to your Radar and MFD are correct and free from damage and then power cycle your system.
Transmitting If your Radar scanner is connected, powered up and transmitting then the Radar image is displayed and echoes/targets are displayed onscreen. Radar modes The Radar app provides preset modes that can be used to quickly achieve the best picture depending on your current situation. Only Radar modes supported by your Radar scanner are shown. To change Radar mode select the required mode from the Radar app menu.
COASTAL Coastal mode takes into account slightly higher levels of Sea clutter that is encountered out of Harbor, useful when in open water but keeping to the coast. Radar scanners: All. OFFSHORE Offshore mode takes into account high levels of Sea clutter so that targets are still visible, useful when navigating in open water away from the coast. Radar scanners: All. BIRD Bird mode optimizes the display to help identify flocks of birds, useful when trying to locate a fishing area.
2. Select the Scanner: box on the Transmission tab. A list of available Radar scanners is displayed. 3. Select the Radar scanner that you want to associate with the current instance of the Radar app. 4. Close the Settings page. The current instance of the Radar app will change to display the selected Radar scanner. Radar scanner selection shall persist over a power cycle. Alternatively, with the Radar powered off or in Standby, you can select switch Radar scanner by selecting Change scanner.
Chapter 7: Dashboard app 7.1 Dashboard app overview The Dashboard app enables you to view system data. System data may be generated by your MFD or by devices connected to your MFD via SeaTalkng ® / NMEA 2000 and SeaTalkhs ™. The Dashboard app can also be configured to provide control of your compatible Digital Switching devices. Note: For data to be available in the Dashboard app it must be being transmitted to your MFD from compatible hardware using supported protocols and messages.
Icon Description Function Waypoint / MOB Place waypoint / activate Man overboard (MOB) alarm. Left arrow Displays the previous data page. Right arrow Displays the next data page. Switching data page 1. Use the Left arrow and Right arrow buttons, located at the bottom of the screen, to cycle through the available data pages. 2. Alternatively, you can select a specific data page from the Dashboard app menu.
Chapter 8: Camera app 8.1 Camera app overview IP (Internet protocol) video feeds can be viewed, recorded and played back using the Camera app. Examples of IP video feeds include: IP CCTV camera and IP Thermal imaging camera. It may be possible to view analog video feeds when using a suitable Analog to IP video converter. Up to 4 IP video feeds can be displayed simultaneously when using a splitscreen app page.
Icon Description Function Stop Stop recording (Replaced Record icon when not recording.) Take photo Take a photo of what is currently displayed in the active feed. Opening the Camera app The Camera app is opened by selecting an app page from the Homescreen that includes the Camera app. Pre-requisites: 1.
Camera not yet available The camera ‘xxx not yet available.....’ message is displayed if: • a Camera app page is opened before the camera has finished booting up. • connection to the camera is lost. If the camera ‘xxx not yet available.....’ message is displayed for more than 2 minutes, then your MFD cannot connect to your camera. Ensure network and power connections to your camera and MFD are correct and free from damage and then power cycle your system.
Chapter 9: Audio app 9.1 Audio app overview The Audio app can be used to control a compatible NMEA 2000 entertainment system that is connected to the same SeaTalkng ® network. The Audio app can be displayed in Fullscreen and half screen portrait app pages. If more than 1 compatible Entertainment system is present on the network then the first system to obtain a network connection will be controlled by the Audio app. Only the Entertainment system that you want to control should be connected to the network.
Audio app controls Icon Description Function Home icon Takes you to the Homescreen. Menu icon Opens the app menu. Waypoint / MOB Place waypoint / activate Man overboard (MOB) alarm. Power Off Powers off the Entertainment system. Mute All Mutes all audio zones. Volume Down Decreases volume for current zone. Volume Up Increases volume for current zone.
Icon Description Function Repeat • Off • Repeat Track • Repeat All Shuffle • On • Off Play Select to commence playback. Pause Select to Pause playback. Stop Select to Stop (Mute) Radio devices. Like Like a track (Pandora only). Dislike Dislike a track (Pandora only). Radio presets Save your favorite radio stations/channels to 4 preset buttons. Press and hold to save, press once to change to saved station/channel.
Audio app displayed If your Entertainment system is powered up and operational then the Audio app is displayed and can be used to control your system. Entertainment system powered off If the Entertainment system is powered off then the Power icon is displayed, selecting the Power icon will switch your Entertainment system on. No audio devices found If the ‘No audio device found’ message is displayed for more than 10 seconds, then your MFD cannot connect to your Entertainment system.
Selecting an audio source 1. Select the audio source you want to listen to from the app Menu. The audio source must be available to your Entertainment system’s head unit for you to be able to select the source from your MFD.
60
Raymarine Marine House, Cartwright Drive, Fareham, Hampshire. PO15 5RJ. United Kingdom. Tel: +44 (0)1329 246 700 www.raymarine.
