C-Series Displays Installation Manual Document # 87020_1 Date: January 2004 offered by Busse-Yachtshop.
Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (Registered in all major marketing territories).
Contents 1 Contents Important Information ..........................................................................5 EMC Installation Guidelines ............................................................................ 7 Radar Scanners ...............................................................................................8 Digital Sounder Module .................................................................................. 9 Electronic Cards ................................................
2 C-Series Reference Manual How are the cable connections made on the display? ...................................32 2.6 How can the display unit be mounted? ...............................................................32 How is the mounting bracket fitted? .............................................................33 How is the unit console mounted? ................................................................35 How is the front bezel attached to the display? ......................................
Contents 3 Appendix A: Specification ...................................................................57 General .........................................................................................................57 Radar Features ..............................................................................................58 Chartplotter Features ....................................................................................59 Fishfinder .......................................................
4 C-Series Reference Manual offered by Busse-Yachtshop.
-5 Important Information Intended use This handbook provides information and instructions to assist in planning and installing your Raymarine C-Series Display. It also provides information that will be useful when you are connecting the C-Series Display to other equipment. Safety notices WARNING:Navigation aid This product is intended to be used as an aid to navigation.
-6 C-Series Displays Installation Manual CAUTION: Radar Scanners, Cables & Installation Information on radar scanners, cables and their installation contained in this handbook supersedes that contained in the Pathfinder Radar Scanner Handbook, Document No. 81154_6, dated 11th March 2002. CAUTION: Bezel Installation After installing the front bezel, check that all buttons and softkeys have passed through the bezel completely and are free to operate correctly.
-7 EMC Installation Guidelines All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised.
-8 C-Series Displays Installation Manual Radar Scanners CAUTION: Radar Scanners, Cables & Installation Information on radar scanners, cables and their installation contained in this handbook supersedes that contained in the Pathfinder Radar Scanner Handbook, Document No. 81154_6, dated 11th March 2002. To achieve full radar compatibility with your C-Series Display, your Raymarine radar scanner may require upgrading. Please check the list below to see if this upgrade is required.
-9 Digital Sounder Module Your Digital Sounder Module (DSM) should be C-Series compliant as indicated on the packaging. If your DSM requires upgrading you will need to obtain a suitable accessory kit, Part No: E05014 from your local Raymarine dealer. Electronic Cards Navionics Chart cards To use your C-Series Display as a navigation aid, charts with detailed information for the area you wish to navigate are required. The charts are available on Navioinics® Chart cards.
-10 C-Series Displays Installation Manual offered by Busse-Yachtshop.
Chapter 1: System Integration -11 Chapter 1: System Integration 1.1 Introduction This chapter provides an overview of system integration, you may find that your system does not use all the protocols or contain all the instrumentation that is described in it. However it is hoped that the information supplied will help in your understanding of how systems can be integrated and used successfully. 1.
-12 C-Series Displays Installation Manual What is NMEA? NMEA 0183 The NMEA 0183 Data Interface Standard was developed by the National Marine Electronics Association of America. It is an international standard to enable equipment from many different manufacturers to be connected together and share information. The NMEA 0183 standard carries similar information to SeaTalk. However it has the important difference in that one cable will only carry information in one direction.
Chapter 1: System Integration -13 1.3 How is the C-Series display integrated? This section details the recommended methods of integration. SeaTalk system Radome GPS C-Series Display Radar Alpha-numeric keypad PAGE ACTIVE WPTS/ MOB DATA MENU OUT RANGE IN OK CANCEL Power IN SeaTalk SeaTalk DSM 250 DSM Power IN Terminator Power IN D6610-1 In this system: • C-Series powers SeaTalk for an alpha numeric keypad and RS 120.
-14 C-Series Displays Installation Manual Integrated system1 Open Array Wind Transducer GPS VHF/DSC Radio RS232 Interface box RAY240 Power IN NMEA OK MENU CH 16/9 HI/LO WX SCAN WATCH SQ C120 PAGE Wind display Depth display ACTIVE Speed display WPTS/ MOB DATA MENU OUT RANGE RS232 Interface box IN OK CANCEL NMEA NMEA SeaTalk DSM 250 Power IN Power IN Power IN Power IN Depth Transducer Speed Transducer Transducer D6622-1 In this system: • PC displays instrument information and
Chapter 1: System Integration -15 Integrated system 2 ## Open Array Wind Transducer GPS VHF/DSC Radio RS232 Interface box RAY240 OK MENU CH 16/9 Power IN Base Transceiver Unit C120 Depth display WATCH SQ RS232 Wind display HI/LO WX SCAN PAGE Speed display ACTIVE WPTS/ MOB DATA MENU OUT RANGE IN OK CANCEL Power IN Power IN SeaTalk Fast Heading Sensor DSM 250 NMEA Power IN Depth Transducer Speed Transducer Compass SeaTalk Power IN Transducer D6623-1 In this system: • PC displa
-16 C-Series Displays Installation Manual Integrated system 3 GPS Digital display PAGE PAGE ACTIVE ACTIVE WPTS/ MOB WPTS/ MOB DATA DATA MENU MENU OUT OUT RANGE RANGE IN SeaTALK 2 OK IN CANCEL OK Power IN NMEA 0183 Digital display VHF/DSC Radio Radome Wind Transducer CANCEL Power IN SeaTalk NMEA 0183 5-way connector and terminator Data Processing Unit ST8001 DSM 250 Course Computer SeaTALK 2 Wind Pod Depth Pod Speed Pod Power IN NMEA 0183 Compass Power IN To Drive Unit
Chapter 2: Installation -17 Chapter 2: Installation CAUTION: Radar Scanners, Cables & Installation Information on radar scanners, cables and their installation contained in this handbook supersedes that contained in the Pathfinder Radar Scanner Handbook, Document No. 81154_6, dated 11th March 2002. 2.
-18 C-Series Displays Installation Manual • Magnetic compass: Mount the display at least 3ft (1m) away from a magnetic compass. • Cable runs: The display should be mounted as near as possible to a Direct Current (DC) power source. • Environmental: The display should be protected from physical damage and excessive vibration. Although the display unit is waterproof, it is good practice to mount it in a protected area away from prolonged and direct exposure to rain and salt spray.
-19 227 mm (8.9 in) Chapter 2: Installation Rear 302.5 mm (11.9 in) 151.25 mm (5.95 in) 116.5 mm (4.6 in) Rear 233 mm (9.2 in) 468 mm (18.4 in) dia. Weight: 6.5 kg (14.3 lbs) Compass safe distance: 1 m (33 in) 18" Radome Scanner D3224_4 227 mm (8.9 in) 141.5 mm (5.6 in) Rear 402 mm (15.8 in) 185.15 mm (7.3 in) 116.5 mm (4.6 in) Rear 233 mm (9.2 in) 599 mm (23.6 in) dia. Weight: 7.5 kg (16.5lbs) Compass Safe Distance: 1m (33") 141.5 mm (5.6 in) offered by Busse-Yachtshop.
-20 C-Series Displays Installation Manual Open Array Scanners 48"- 1306 mm (51.4 in), 72"- 1928 mm (75.9 in) Centre of rotation 406 mm (16 in) Centre of rotation 100 mm (4 in) 427 mm (16.8 in) Weight Pedestal: 24 kg (53.0 lb) 48" Open Array: 6 kg (13.2 lb) 72" Open Array: 9.4 kg (20.7 lb) Compass Safe Distance: 1 m (33 in) Minimum clearance height 510 mm (20.1 in) 150 mm (6 in) 70 mm (2.75 in) 140 mm (5.5 in) 296 mm (11.65 in) Minimum clearance 630 mm (24.
Chapter 2: Installation -21 (45 ft) for open array scanners. If you need to use a longer cable power cable lengths must be considered. • Shadow sectors and false echoes: Mount the scanner away from large structures or equipment, such as the fly bridge, large engine stacks, searchlights, horns, or masts. It is particularly important to avoid shadow sectors near the bow. Raising or even lowering the scanner may help to reduce these effects.
-22 C-Series Displays Installation Manual best suited for sailboat operation as open array systems are more difficult to protect from ropes and sails. For sailboat installations, Raymarine offers a universal mast mount kit for each radome scanner type. This optional mount is used to fit a radome scanner to a flat surface on a mast with a minimum diameter of 60 mm (2½ in). When using the mast mount kit, appropriate hardware should be used for the style and structure of the mast aboard the vessel.
Chapter 2: Installation -23 . Wedge or washers Forward Using shims to lower the main beam D3229-3 The shims may be made from aluminium plate wedges, simple flat washers, or an angled wooden block. For thick shims, you may need longer securing bolts than the M8x40 bolts supplied with the radome scanner, or the M10 studding supplied with the open array scanners. offered by Busse-Yachtshop.
-24 C-Series Displays Installation Manual 2.2 What comes in the box? Unpack the display carefully, to prevent damage. Save the carton and packing, in case the unit has to be returned for service. The box contains the following items: Item Quantity C-Series Display 1 Display Bezel 1 Trunnion Bracket and knobs 1 Panel mounting seal 1 Sun cover 1 Power Cable 1 NMEA cable 1 SeaTalk cable 1 No.
Chapter 2: Installation -25 2.3 What size is the display unit? The dimensions for your C-Series display are: C70 Display PAGE 177 mm (6.96 in) WPTS MOB DATA MENU OUT RANGE IN OK 189 mm (7.44 in) ACTIVE CANCEL 9.5 mm (0.375 in) 253 mm (10 in) 89.4 mm (3.5 in) 282 mm (11.1 in) 220 mm (8.66 in) plug clearance D6612-1 C80 Display PAGE ACTIVE MENU OUT RANGE IN OK 222 mm (8.75 in) DATA 212.5 mm (8.4 in) WPTS MOB CANCEL 9.5 mm (0.375 in) 283 mm (11.14 in) 312 mm (12.3 in) 89.3 mm (3.
-26 C-Series Displays Installation Manual C120 Display PAGE ACTIVE MENU OUT RANGE IN OK 267 mm (10.5 in) DATA 276.66 mm (10.9 in) WPTS MOB CANCEL 9.5 mm (0.375 in) 357 mm (14 in) 385 mm (15.15 in) 87.9 mm (3.46 in) 220 mm (8.66 in) plug clearance D6611-1 2.4 What about the cables? When installing system cables consider the following: • All cables should be adequately secured, protected from physical damage and exposure to heat.
Chapter 2: Installation -27 2.5 What cables will be needed? You will need to install and connect the following cables to ensure that your CSeries Display functions correctly: Power input cable This cable is supplied prepared for connecting to your boats DC power supply. The cable is supplied with a length of screen exposed before the positive and negative wire tails.
-28 C-Series Displays Installation Manual Power supply • The C-Series Display is intended for use on boats’ DC power systems rated at 12 V or 24 V.
Chapter 2: Installation -29 NMEA Input cable The NMEA input cable is supplied with exposed wire connecting tails.These should be connected to your existing NMEA instruments using suitable connector blocks as follows: Function Color NMEA Input (+ve) White NMEA Input (-ve) common Green Not connected Gray NMEA Output (+ve) Yellow NMEA Output (-ve) common Brown Not connected Screen Fish finder cable The fishfinder cable is supplied with your Digital Sounder Module (DSM).
-30 C-Series Displays Installation Manual Radar cable Having ensured that the radar scanner you are using is compatible with the CSeries Display, the cable should be connected as follows: Radome If you are using a radome this can be powered through the display. Just run your cable and connect it to the radome and the display.
Chapter 2: Installation -31 Open array If you are using an open array, this cannot be powered through the display.
-32 C-Series Displays Installation Manual The split pedestal cable should be run and connected as follows: Connect to C-Series display Connect to open array scanner cable Cable splitter Connect to boat's DC power supply D6620-1 You should ensure that the distance (cable route) from the power supply to the open array is kept to a minimum.
Chapter 2: Installation -33 How is the mounting bracket fitted? The mounting bracket can be used to fit the display unit on a dash, chart table, bulkhead or deckhead: D6739_1 You should fit the mounting bracket as follows: 1. Mark the location of the mounting bracket screw holes on the chosen mounting surface. 2. Drill pilot holes for the screws using a suitable drill, taking care that there are no cables or anything that may be damaged behind the surface. 3.
-34 C-Series Displays Installation Manual 5. Attach the display unit to the mounting bracket. 6. Locate the bezel over the front of the display. See “How is the front bezel attached to the display?” on page 37. 7. Check that the buttons have passed through the bezel and are free to operate. It is suggested that you use your thumb or forefinger in a circular motion to do this. 8. Adjust the unit to the required angle for clear vision, and tighten the knobs offered by Busse-Yachtshop.
Chapter 2: Installation -35 How is the unit console mounted? D6738_1 You should console mount your display using the template which can be found in the document wallet, as follows:. CAUTION: Installation Make sure there are no hidden electrical wires or other items behind the selected location before proceeding. Make sure there is sufficient rear access for mounting AND CABLING. 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel, is required. 2.
-36 C-Series Displays Installation Manual 5. Remove the mounting bracket knobs and the mounting bracket from the display unit. Make sure the unit fits in the area that has been cut out. 6. Drill four 4.5 mm holes as indicated on the template to accept the securing bolts. 7. Place trim ring into the cut-out, ready for securing the unit. 8. Place the gasket onto the display unit. 9. Connect the DC power cable, scanner cable, SeaTalk and Fishfinder connector cables to the display, avoiding tight bends. 10.
Chapter 2: Installation -37 How is the front bezel attached to the display? After you have installed the C-Series Display in the required position, you should attach the front bezel as follows: 1. Carefully lift one edge of the screen protection film, so that it is accessible for removing when unit installation is complete. 2. Place the bezel over the front of the C-Series Display, ensuring that locking lugs located at the bottom edge of the bezel are latched into position. 3.
-38 C-Series Displays Installation Manual How do I remove the front bezel? D6616-1 To remove the front bezel: 1. Using a flat-bladed screwdriver placed in the aperture at the top right of the bezel, gently twist it to release the top clips. 2. Working from this corner, free the clips along the top edge of the display, then work towards the bottom edge. Taking care to ensure that the control buttons pass through the bezel. DO NOT lever along the top edge. 3.
Chapter 3: System Tests and Alignment -39 Chapter 3: System Tests and Alignment 3.1 Introduction This chapter deals with the system tests and alignment for the applications that can be used with your C-Series Display, and covers the following: • Radar tests and alignment. • Chartplotter checks. • Fishfinder checks. If your C-Series Display is part of an integrated system, it is strongly advised that the radar checks are carried out before connecting the other systems.
-40 C-Series Displays Installation Manual WARNING:Electromagnetic energy The radar scanner transmits electromagnetic energy. Ensure that the scanner has been installed according to the recommendations in the relevant scanner handbook. Ensure all personnel are clear of the scanner, before switching to transmit mode. Testing and alignment You should test and align the radar as follows: 1. Press POWER to turn the display on. 2. Press MENU or hold down PAGE. The SELECT PAGE SET menu is displayed. 3.
Chapter 3: System Tests and Alignment -41 Alignment checks With the radar transmitting correctly, the system should now be aligned as follows: Bearing alignment To adjust the bearing alignment, you need to select a visible target of known bearing that is displayed on the radar, and then adjust the radar set up as necessary until the correct bearing reading is obtained. You can carry out a bearing alignment with your boat moored, or under way in reasonably calm conditions.
-42 C-Series Displays Installation Manual Adjusting the bearing alignment To adjust the bearing alignment: 1. Press MENU. The Set Up menu is displayed. 2. Use the trackpad up /down to highlight RADAR SET UP. 3. Use trackpad right to display the RADAR SET UP menu. 4. Use the trackpad up/down to highlight BEARING ADJUSTMENT. The menu is removed from the screen, the BEARING ADJUSTMENT softkey is displayed. 5. Press BEARING ADJUSTMENT softkey. Then either: 6.
Chapter 3: System Tests and Alignment -43 Display timing adjustment To adjust the display timing: 1. Press MENU. The Set Up menu is displayed. 2. Use the trackpad up /down to highlight RADAR SET UP. 3. Use trackpad right to display the RADAR SET UP menu. 4. Use the trackpad up/down to highlight RADAR ADVANCED SET UP. 5. Use the trackpad right to select this option. The advanced set up softkeys are displayed, and the menu is removed from the screen. 6. Press the DISPLAY TIMING softkey. 7.
-44 C-Series Displays Installation Manual 3. Press OK to select. 4. Use the trackpad up/down to highlight RADAR ADVANCED SET UP. The set up soft keys will be displayed. 5. Press the corresponding soft key for the parameter you wish to adjust. The soft key label is highlighted. 6. Use the rotary control to adjust the parameter value in the box above the soft key. 7. Press OK or use the rotary end push to accept the adjustment. 8. Repeat steps 5 through 7 to adjust next parameter.
Chapter 3: System Tests and Alignment -45 3.4 How do I test the Chartplotter? When you have connected your C-Series Display, it is necessary to ensure that position data is available at the display via SeaTalk or NMEA. To confirm that your chartplotter is working correctly: 1. Without a chart card installed, select the Chart application and use the RANGE button to select a suitable range scale. Verify that the world map is visible. 2.
-46 C-Series Displays Installation Manual Narrow Groove Lip D6517-1 Inserting a card To insert a card, refer to the illustration, and: 1. Check that you are using the correct type of card. See “Electronic Cards” on page 9. 2. Open the chart card door, located on the front left of the display. 3. Insert the card as shown, with the lip of the card facing inwards, it should position easily. If it does not, DO NOT force it, check the direction in which the lip is facing. 4. Gently press the card home. 5.
Chapter 3: System Tests and Alignment -47 D6518-1 Removing a card To remove a card with the unit powered down, refer to the illustration, and: 1. Open the chart card door. 2. Grip the card and pull to remove it from its slot. 3. To prevent the ingress of water and consequent damage, close the chart card door and press firmly until an audible click is heard. To remove a card with the unit powered, refer to the illustration, and: 1. Press MENU. The System Set Up menu is displayed. 2.
-48 C-Series Displays Installation Manual 4. The system will now complete its checks, on completion the following message will appear: You may now safely remove your CompactFlash card Press OK or CANCEL when finished 5. Open the chart card door. 6. Grip the card and pull to remove it from its slot. 7. To prevent the ingress of water and consequent damage, close the chart card door and press firmly until an audible click is heard. 8. Press OK.
Chapter 3: System Tests and Alignment -49 3.5 How do I test the Fishfinder? When you have connected your C-Series display to the DSM, you should open the Fishfinder application and check that information is being displayed. Using the soft keys check that individual settings change as they are selected and that all the options are available. Received data With the data cable connected to the DSM, verify that expected data is shown.
-50 C-Series Displays Installation Manual offered by Busse-Yachtshop.
Chapter 4: Maintenance & Troubleshooting -51 Chapter 4: Maintenance & Troubleshooting 4.1 Introduction This chapter provides information on maintaining and troubleshooting your Raymarine C-Series Display, and also information on how to get assistance from Raymarine. 4.2 What maintenance can I do? At regular intervals, carry out the following servicing procedures: • Routine checks. • Cleaning the Display. Do not attempt any other servicing procedures.
-52 C-Series Displays Installation Manual How do I clean the display? CAUTION: Cleaning the display Take care when cleaning the display, to avoid damaging it. Do NOT wipe the display screen with a dry cloth, as this could scratch the screen coating. Do NOT use acid, ammonia based or abrasive products. (1) (2) Regularly clean your Display as follows: 1. Switch off the power to the Display. 2. Wipe the Display with a clean soft cloth.
Chapter 4: Maintenance & Troubleshooting -53 What is a factory reset? CAUTION: Factory Reset The factory reset will set all values back to their original factory settings. This reset also clears the Waypoint and Route List databases. How do I carry out a factory reset? To carry out a factory reset: 1. Press and hold the left hand soft key. 2. Press POWER to power-up the display. The factory reset will take place during this operation.
-54 C-Series Displays Installation Manual What are the common problems and how do I solve them? Problem Solution Display does not function 1. Make sure that the power supply cable is sound and that all connections are tight and free from corrosion. 2. Check relevant fuses. “Scanner not responding” message Check that the cable connecting the scanner to the radar display unit is securely connected and undamaged. “Invalid scanner software: Version xx.x, Version xx.
Chapter 4: Maintenance & Troubleshooting -55 How can I contact Raymarine in the US? You can contact Raymarine in the US either using the Raymarine world wide web as detailed above or by calling one of the telephone numbers below. Who do I contact for accessories and parts? You can obtain many Raymarine accessories and parts directly from your authorized Raymarine dealer.
-56 C-Series Displays Installation Manual If you wish to enquire about the repair status of your unit, contact the Repair Center at: 1-800-539-5539 How can I contact Raymarine in Europe? You can obtain Technical Support, service and accessories from your authorized Raymarine dealer, or by contacting: Raymarine Limited Anchorage Park, Portsmouth PO3 5TD, England Tel +44 (0)23 9271 4713 Fax +44 (0)23 9269 4642 offered by Busse-Yachtshop.
57 Appendix A: Specification C70, C80 and C120 LCD Color Displays General Approvals CE - conforms to FCC - conforms to 1999/5/EC, EN6095:1997 Part 80 (47CFR) and Part 2 (47CFR) Size C70 C80 C120 253 x 175 x 110 mm (9.9 x 6.9 x 4.3 in.) excluding bracket 283 x 210 x 110 mm (11.1 x 8.2 x 4.3 in.) excluding bracket 356 x 264 x 114 mm (14.0 x 10.4 x 4.5 in.) excluding bracket Weight C70 C80 C120 1.2 kg. (2.6 lbs) 1.8 kg. (3.9 lbs) 3.0 kg. (6.
58 C-Series Displays Installation Manual General Connectors 13 pin Radar scanner 4 pin DSM 3 pin SeaTalk 5 pin NMEA 5 pin SeaTalk2/ NMEA2000 3 pin Power Interfaces Pathfinder Radar scanner 1 x DSM receive 1 x SeaTalk, receive and transmit 1 x NMEA0183, receive and transmit 1 x SeaTalk2/ NMEA2000 CompactFlash card slot Waypoints 1000 waypoints entered via cursor, lat/lon, range and bearing from present position or at boats position. 16 character name can be assigned.
59 Radar Features Scanner Control Interference rejection, standby/transmit modes, pulse selection, Tune, Rain, FTC and Sea controls, with selection of manual or automatic control of gain, sea clutter and tune (Auto GSTTM) Magnetic Sensor NMEA (required for fast heading data, suitable for MARPA), or SeaTalk Waypoint Display Target waypoint displayed with User control of symbols and groups MARPA Manual acquisition of 10 targets, automatic tracking, dangerous target alarms, safe zone, target history, t
60 C-Series Displays Installation Manual Chartplotter Features Navigation information Own boats position in lat/lon, XTE, TTG and SOG/COG selectable. Bearing and distance to waypoint. Bearing and distance to cursor and ETA.
-61 List of Abbreviations Abbreviation Description °C Degrees Centigrade amps Amperes AWG American Wire Gauge CCFL Cold Cathode Florescent Lamp CDI Course deviation Indicator COG Course Over Ground DC Direct Current DSM Digital Sounder Module EBL Electronic Bearing Line EMC ElectroMagnetic Compatibility FCC Federal Communications Commission FTC Fast Time Constant kg Kilograms km Kilometres kyds Kiloyards lat.
-62 C-Series Displays - Installation Manual Abbreviation Description MOB Man Overboard nm Nautical miles NMEA National Marine Electronics Association SHM Ships Heading Marker sm Statute Miles SOG Speed Over Ground SSB Single Side Band TFT Thin Film Transistor TTG Time To Go US United States V Volts VRM Variable Range Marker XTE Cross Track Error yds Yards offered by Busse-Yachtshop.