N e w c S e r ie s N e w e S e r ie s Ins ta lla tion a nd ope ra tion ins tructions En g lis h Da te : 08-2012 Docume nt numbe r: 81337-4-EN © 2012 Ra yma rine UK Limite d
Trademark and patents notice Autohelm, hsb2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalkNG, SeaTalkHS and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.
Contents Chapter 1 Important information............................... 9 4.11 NMEA 2000 connection ........................................... 44 TFT Displays ....................................................................9 4.12 Video connection..................................................... 45 Water ingress ...................................................................9 Disclaimers ......................................................................9 4.13 Video in-out connection ...
10.1 Waypoints............................................................... 94 13.13 AIS alarms .......................................................... 155 10.2 Routes.................................................................... 98 13.14 Buddy tracking .................................................... 155 10.3 Tracks .................................................................. 102 10.4 Waypoints, routes and tracks storage capacity ....................................................
Chapter 19 Using a remote control....................... 207 25.11 Touchscreen troubleshooting ................................ 260 19.1 Remote control connection .................................... 208 25.12 Miscellaneous troubleshooting ............................. 261 19.2 Pairing the remote and configuring the UP and DOWN buttons ............................................................. 208 19.3 Operating principles ..............................................
New c Series / New e Series
Chapter 1: Important information Caution: Power supply protection Warning: Product installation and operation When installing this product ensure the power source is adequately protected by means of a suitably-rated fuse or automatic circuit breaker. This product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance.
charts and notices to mariners contain all the current information needed for safe navigation, and the captain is responsible for their prudent use. It is the user’s responsibility to use official government charts, notices to mariners, caution and proper navigational skill when operating this or any other Raymarine product. This product supports electronic charts provided by third party data suppliers which may be embedded or stored on memory card.
2. cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Third party software license agreements This product is subject to certain third party software license agreements as listed below: • GNU — LGPL/GPL Warranty registration To register your Raymarine product ownership, please visit www.raymarine.com and register online.
New c Series / New e Series
Chapter 2: Handbook information Chapter contents • 2.1 Handbook information on page 14 • 2.2 Handbook illustrations on page 14 • 2.
2.1 Handbook information 2.2 Handbook illustrations This handbook contains important information regarding your multifunction display. The illustrations and screenshots used in this handbook may differ slightly from your display model. The handbook is for use with Raymarine’s New c Series and New e Series multifunction displays. About this handbook This handbook describes how to operate your multifunction display in conjunction with compatible electronic cartography and peripheral equipment.
2.3 Handbook conventions The following conventions are used throughout this handbook when referring to: Type Icons Example Convention The term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: • Touch — Press your finger on the icon to select. • Physical buttons — Use the Joystick to highlight the icon and press the Ok button.
New c Series / New e Series
Chapter 3: Planning the installation Chapter contents • 3.1 System integration on page 18 • 3.2 Installation checklist on page 22 • 3.3 System Limits on page 22 • 3.4 Multiple data sources (MDS) overview on page 23 • 3.5 Identifying your display variant on page 23 • 3.6 Networking constraints on page 24 • 3.7 Compatibility on page 24 • 3.8 Typical systems on page 25 • 3.9 System protocols on page 27 • 3.10 Data master on page 28 • 3.11 Parts supplied on page 28 • 3.
3.1 System integration Your multifunction display is compatible with a wide range of marine electronics devices. 1 2 3 5 4 P IT L O 7 6 8 SMARTPILOT RAY240 9 17 10 11 18 12 13 15 14 16 21 19 20 22 D12244-1 The display uses a number of protocols to transfer data between the various devices in your system.
Item Device Type Maximum quantity Suitable Devices Connections 5 Instruments — Raymarine As determined by SeaTalkng bus bandwidth and power loading. SeaTalk (via optional SeaTalk to SeaTalkng converter): SeaTalk, SeaTalkng. • ST40 Wind, Speed, Depth, Rudder, or Compass. • ST60+ Wind, Speed, Depth, Rudder, or Compass. • i40 Wind, Speed, Depth, or Bidata SeaTalkng: • ST70. • ST70+. • ST70+ keypads. • i50 Depth, Speed, or Tridata • i60 Wind, CH Wind • i70.
Item Device Type Maximum quantity Suitable Devices Connections 13 Transducers and sensors — Raymarine 1 Analog transducers: SeaTalkng (via optional transducer pods). • Wind. • Speed. • Depth. 13 Transducers and sensors — Airmar 1 • DT800 Smart Sensor. SeaTalkng (via optional transducer pods). • DST800 Smart Sensor. • PB200 weather station. 14 Video out New e Series (excluding e7 and e7D) = 1 External display. 15 pin D-Type connector (VGA Style).
Item Device Type Maximum quantity Suitable Devices Connections 20 Radar — Raymarine 1 All Raymarine Non-HD Digital Radomes and HD or SuperHD radar scanners. SeaTalkhs. Note: Please ensure your radar scanner is using the latest software version. 21 Thermal camera — Raymarine 1 All Raymarine thermal cameras. SeaTalkhs (for control), BNC connector (for video). 22 PC / laptop 1 Windows-compatible PC or laptop running Raymarine Voyager planning software.
3.2 Installation checklist 3.3 System Limits Installation includes the following activities: The following limits apply to the number of system components that can be connected in a New c Series / New e Series system. Installation Task 1 Plan your system. 2 Obtain all required equipment and tools. 3 Site all equipment. 4 Route all cables. 5 Drill cable and mounting holes. 6 Make all connections into equipment. 7 Secure all equipment in place. 8 Power on and test the system.
3.4 Multiple data sources (MDS) overview 3.5 Identifying your display variant Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. • Speed. To discover which model display you have follow the steps below: From the homescreen: 1. Select Set-up. 2. Select Maintenance. 3. Select Diagnostics.
3.6 Networking constraints 3.7 Compatibility The following constraints apply when networking your multifunction display with other devices. New c Series and New e Series multifunction displays can be connected to systems containing Raymarine E-Widescreen displays and G series systems. However caution is advised as there are networking constraints and restrictions which apply.
3.8 Typical systems Example: Basic system 1 2 3 S M A R T IP L O 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkng D12245-1 1. Multifunction display. 2. Raymarine network switch. 3. Raymarine radar scanner. 4. SPX course computer. 5. Pilot controller. Note: A network switch is only required if multiple devices are connected using SeaTalkhs / RayNet.
Example: Expanded system 5 SeaTalkhs / RayNet 8 6 7 4 9 SeaTalkng 3 SeaTalkng 2 SeaTalkng 1 SeaTalkng 10 15 DeviceNet 11 12 12 13 14 SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkhs / RayNet D12247-1 1. Raymarine radar scanner. 2. Weather sensor. 3. Sirius weather receiver. 4. Raymarine sonar module. 5. Pilot controller. 6. Instrument display. 7. AIS receiver / transceiver. 8. Audio system. 9. Smartphone / tablet. 10. DeviceNet spur (for NMEA 2000 devices). 11. Raymarine network switch.
3.9 System protocols Your Multifunction Display can connect to various instruments and displays to share information and so improve the functionality of the system. These connections may be made using a number of different protocols. Fast and accurate data collection and transfer is achieved by using a combination of the following data protocols: • SeaTalkhs • SeaTalkng • NMEA 2000 e.g. a compass sensor transmitting heading to a radar display.
3.10 Data master 3.11 Parts supplied Any system containing more than one networked multifunction display must have a designated data master. The parts shown below are supplied with the e7 / e7D multifunction display. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
3.12 Parts supplied 3.13 Tools required for installation The parts shown below are supplied with the c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 multifunction display. 1 2 3 4 5 4 3 6 2 5 6 1 7 8 D12171-1 1. Power drill. 2. Jigsaw. 3. Pozidrive screwdriver. 7 4. Adhesive tape. D12248-1 5. Drill bit for trunnion bracket mounting. 1. Sun cover. 6. File. 2. Front bezel. 7. 25 mm hole saw for flush mounting. 3. Multifunction display. 8. Drill bit for flush mounting. 4.
New c Series / New e Series
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 32 • 4.2 Connections overview on page 33 • 4.3 Power connection on page 34 • 4.4 Network connections on page 35 • 4.5 GPS connection on page 40 • 4.6 AIS connection on page 40 • 4.7 Fastheading connection on page 41 • 4.8 SeaTalkng connections on page 41 • 4.9 SeaTalk connection on page 43 • 4.10 NMEA 0183 connection on page 43 • 4.11 NMEA 2000 connection on page 44 • 4.
4.1 General cabling guidance Cable types and length It is important to use cables of the appropriate type and length • Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run. Routing cables Cables must be routed correctly, to maximize performance and prolong cable life.
4.2 Connections overview The connections for all multifunction display variants are listed below.
4.3 Power connection Power cable The display is supplied with a combined power and data multi cable, this can be extended if required. Power cables available 5 4 1 2 Cable Part number 1.5 m (4.9 ft) Straight power and data cable R62379 1.5 m (4.9 ft) Right angled power and data cable R70029 Notes 3 7 Cable extension The following restrictions apply to any extension to the power cable: 6 • Cable must be of a suitable gauge for the circuit load.
4.4 Network connections You can connect a number of digital devices to your multifunction display using the Network connector(s) at the rear of the unit. A typical network of digital devices may include: • Up to 6 Raymarine multifunction displays. • SeaTalkhs or RayNet digital devices such as a sonar module or radar scanner. • Thermal camera. Note: The display includes either 1 (e7 / e7D only) or 2 network connectors, networks requiring additional connections will require a Raymarine network switch.
Cable Part number 4. RayNet to SeaTalkhs network cable. 10 m (32.8 ft) RayNet to RayNet cable A62362 5. SeaTalkhs crossover coupler 20 m (65.6 ft) RayNet to RayNet cable A80006 6. VCM (Voltage Converter Module) — required for Open Arrays. RayNet cable puller 5 pack R70014 7. Power connection. Radar connected using crossover coupler SeaTalkhs network cables Cable Part number 1.5 m (4.9 ft) SeaTalkhs network cable E55049 5 m (16.4 ft) SeaTalkhs network cable E55050 10 m (32.
Radar cable extension For longer cable runs a radar power and data digital cable extension is required. 1 2 3 4 D12254-1 1. Radar extension cable. 2. Radar power and data digital cable. 3. Raymarine network switch (or crossover coupler if connecting radar directly to display). 4. RayNet cable (or RayNet to SeaTalkhs cable if connecting via crossover coupler). Note: The extension cable connects to the radar scanner. Note: The power connection is NOT shown in the diagram.
Sonar module connection 600 watt sonar-compatible sonar transducer connection via optional adaptor — Sonar variant multifunction displays 1 1 4 2 2 SeaTalkhs / RayNet 3 D12257-1 3 1. Rear connector panel of multifunction display (Sonar variant). 2. E66066 adaptor cable. SeaTalkhs / RayNet D12255-1 1. Rear connector panel of multifunction display (Non-sonar variant). 3. Sonar transducer. Transducer adaptor cable 2. Raymarine network switch. 3. Raymarine sonar module. Cable Part number 0.
• “Dual payload” thermal cameras include 2 independent lenses; 1 for thermal (infrared) and 1 for visible light. If you only have 1 display you should only connect the video cable labelled “VIS / IR” (visible light / infrared) to the display. If you have 2 or more displays you should connect 1 cable to each display. 3. Minn Kota transducer cable. 4. Minn Kota transducer.
4.5 GPS connection 4.6 AIS connection The multifunction display includes an internal GPS receiver. It can also be connected to an external GPS receiver, using SeaTalkng or NMEA 0183. A compatible AIS can be connected using SeaTalkng or NMEA 0183. Connection using SeaTalkng GPS connection — SeaTalkng 2 1 1 2 SeaTalkng D12263-1 SeaTalkng D12261-1 1. Multifunction display. 1. Multifunction display. 2. SeaTalkng AIS receiver / transceiver. 2. SeaTalkng GPS receiver.
S M A R T P I L O 4.7 Fastheading connection 4.8 SeaTalkng connections If you wish to use MARPA (radar target acquisition) functions on your multifunction display you need either: The display can connect to a SeaTalkng system. • An autopilot connected to the multifunction display via SeaTalkng or NMEA 0183. The compass is connected to the course computer and calibrated via the pilot control head; or: • A Raymarine or third-party fastheading sensor connected to the multifunction display via NMEA 0183.
SeaTalkng cabling components Description Part No SeaTalkng SeaTalkng to bare ends 3 m (9.8 ft) spur A06044 SeaTalkng Power cable A06049 SeaTalkng Terminator A06031 SeaTalkng T-piece A06028 Provides 1 x spur connection SeaTalkng 5–way connector A06064 Provides 3 x spur connections SeaTalk to SeaTalkng converter E22158 Allows the connection of SeaTalk devices to a SeaTalkng system.
4.10 NMEA 0183 connection 4.9 SeaTalk connection You can connect SeaTalk devices to your multifunction display using the optional SeaTalk to SeaTalkng converter. 3 1 SeaTalkng SeaTalk SeaTalkng 2 D12265-1 1. SeaTalk device. 2. SeaTalk to SeaTalkng converter. 1 2 3 4 5 6 7 8 9 10 11 12 3. Multifunction display. SeaTalk accessories SeaTalk cables and accessories for use with compatible products. Description Part No Notes 3–way SeaTalk junction box D244 1 m (3.
4.11 NMEA 2000 connection Port Input / output Positive (+) / negative (-) * * Output Positive The display can receive data from NMEA 2000 devices (e.g. data from compatible engines). The NMEA 2000 connection is made using SeaTalkng and appropriate adaptor cables.
4.12 Video connection 4.13 Video in-out connection A video device can be connected to the multifunction display using the video connector on the power and data cable. A video device can be connected to e95 / e97 / e125 / e127 variant multifunction display using the video in/out connector. Examples of video sources that you can connect to the display include: Video In • Video camera. Examples of video input sources that you can connect to the display include: • Thermal camera. • Video camera.
Video cables 4.14 Bluetooth connections The following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays. Remote control connection Part number Description R70003 e-series accessory video cable Notes You can control the multifunction display wirelessly using a Raymarine remote control unit. The remote control uses a Bluetooth wireless connection. 1 2 3 D12163-2 1. Multifunction display. 2. Bluetooth connection. 3.
• Enable Bluetooth in the System Settings on the multifunction display. 4.15 WiFi connections • Enable Bluetooth on the media player device. Raymarine app connection • Pair the media player device with the multifunction display. You can use compatible tablet and smartphone devices as a wireless repeat display or remote control for your multifunction display. • Enable Audio Control in the System Settings on the multifunction display.
New c Series / New e Series
Chapter 5: Location and mounting Chapter contents • 5.1 Selecting a location on page 50 • 5.2 Removing the rear bezel on page 52 • 5.3 Flush mounting on page 52 • 5.4 Attaching the rear bezel on page 53 • 5.5 Bracket (trunnion) mounting on page 53 • 5.
5.1 Selecting a location 1 Warning: Potential ignition source 2 6 This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). 250 (9.8 mm 4 in ) 200 (7.8 mm 7 in ) mm 500.7 in) (19 300 (11 mm .8 i n) 350 (13 mm .8 i n) General location requirements mm 700.5 in) 7 (2 When selecting a location for your display it is important to consider a number of factors.
Vessel construction The construction of your vessel can have an impact on GPS performance. For example, the proximity of heavy structure such as a structural bulkhead, or the interior of larger vessels may result in a reduced GPS signal. Before locating equipment with an internal GPS antenna below decks, seek professional assistance and consider use of an external GPS antenna mounted above decks. Item e7 / e7D e95 / e97 / c95 / c97 e125 / e127 / c125 / c127 C 64 mm (2.52 in.) 64 mm (2.52 in.
5.2 Removing the rear bezel 5.3 Flush mounting You must remove the rear bezel before flush-mounting the display. 1. Remove the front bezel. Refer to the separate instructions provided for that procedure. You can mount the display in a flush or panel mounting arrangement. Before mounting the unit, ensure that you have: • Selected a suitable location. • Identified the cable connections and route that the cables will take. • Detached the front bezel.
5.4 Attaching the rear bezel 5.5 Bracket (trunnion) mounting The rear bezel must be fitted if you wish to use a mounting bracket to mount the unit. 1. Remove the front bezel. Refer to the separate instructions provided for that procedure. 2. Place the bezel over the rear of the display, ensuring that it is correctly aligned with the display. Apply firm but even pressure to the bezel along the: i.
5.6 Front bezel Attaching the front bezel 2 The following procedure assumes that the unit has already been mounted in position. 1. Carefully lift one edge of the screen protection film, so that it is accessible for removing when unit installation is complete. 2. Ensure the memory card slot door is in the open position. 3.
Chapter 6: Getting started Chapter contents • 6.1 Display power on page 56 • 6.2 e7 / e7D Controls on page 56 • 6.3 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 Controls on page 57 • 6.4 Multifunction display variants on page 58 • 6.5 Hybridtouch overview on page 59 • 6.6 Touchscreen overview on page 59 • 6.7 Homescreen overview on page 60 • 6.8 System checks on page 60 • 6.9 Enabling autopilot functions on page 63 • 6.10 Enabling AIS functions on page 64 • 6.
6.1 Display power 6.2 e7 / e7D Controls Powering the display on 1 1. Press and hold the POWER button until the Raymarine logo appears. 2. Press OK to acknowledge the disclaimer message. 2 3 Powering the display off 4 1. Press and hold the POWER button until the countdown reaches zero. 5 Note: If the POWER button is released before the countdown reaches zero, the power off is cancelled.
6.3 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 Controls 2 1 UniControl 3 1 4 5 6 7 8 11 10 9 2 D12276-1 1. Touchscreen — you can touch the screen to operate many common functions, including all menu operations (HybridTouch multifunction displays only). 2. Home — Press to return to the homescreen. 3. Menu — accesses menus. Press again to close menus. 4. UniControl — provides a joystick and rotary control and an OK button for using menus and applications. 3 5.
The cursor appears on the screen as a white cross. The table below details which multifunction display variants feature HybridTouch. D7366_3 D7368_2 D7369-2 WPT 6.4 Multifunction display variants If the cursor has not been moved for a short period of time, it changes to a circle with a cross in it, to make it easier to locate on the screen. HybridTouch models Non-Touch models New e Series New c Series The cursor is context-sensitive.
6.5 Hybridtouch overview 6.6 Touchscreen overview If your multifunction display features Hybridtouch, this enables you to operate the unit using the touchscreen and the physical keys. The touchscreen provides an alternative to using physical buttons to control your multifunction display. All functions can be accessed using the touchscreen. However, there may be situations (such as rough sea conditions) when it is not appropriate to use the touchscreen.
6.7 Homescreen overview 6.8 System checks The homescreen provides a central point of access to your display's range of applications. GPS check • The homescreen also provides quick access to your data (waypoints, routes, and tracks). GPS selection • To access the homescreen, hold the MENU button for 3 seconds. Alternatively, select the on-screen Home icon. • The multifunction display features an internal GPS receiver. You can use an internal or external GPS receiver.
5. Select Radar. 6. Select the Transmit option. The radar scanner should now be transmitting and receiving. 7. Check that the radar screen is operating correctly. 2 Typical HD radar screen 3 4 1 6 5 D12204-1 Item Description 1 Sky view — a visual representation of the position of tracked satellites. 2 Satellite status — displays the signal strength and status of each satellite identified in the sky view diagram on the left of the screen.
alignment error and you will need to carry out bearing alignment adjustment. 1. Select the fishfinder page. Adjusting the bearing alignment Once you have checked the bearing alignment you can proceed and make any required adjustments. With the radar application displayed: 1. Press the MENU button. 2. Select Set-Up . 3. Select Advanced. 4. Select Bearing Alignment. 5. Use the rotary control to place the selected target under the Ship’s Heading Marker. 6. Press OK when complete. 2.
In some circumstances it may be better to use just the UniControl's rotary and joystick controls to manipulate the thermal camera view. For example, this method is ideal for finer control over the camera and is particularly useful in rough sea conditions. UniControl joystick — is used for rotating the camera left or right (panning), or tilting the camera up or down. UniControl rotary — is used to zoom in and out. 6.9 Enabling autopilot functions With the homescreen displayed: 1. Select Set-up. 2.
6.10 Enabling AIS functions 6.11 Language selection Before proceeding ensure AIS unit is connected to NMEA Port 1. The system can operate in the following languages: With the homescreen displayed: 1. Select Set-Up. 2. Select System Settings. 3. Select NMEA Set-Up. 4. Select NMEA Input Port 1. 5. Select the AIS 38400 option. 6. Use the Back button to return to the System Settings menu. 7. Select External Devices. 8. Select the AIS unit. The Track Targets menu is displayed. 9.
6.12 Pages Pages are used to display applications. Pages are displayed and accessed on the homescreen. Each page can display up to 4 applications (depending on multifunction display variant). Note: New c Series and New e Series displays (except the e7 / e7D) can configure and show up to 4 applications per page.
6.13 Applications Chart application — provides a 2D or 3D graphical view of your charts to help you navigate. Waypoint, route, and track functions enable you to navigate to a specific location, build and navigate routes, or record where you've been. Chart cards provide higher levels of detail and 3D views. 6.14 Splitscreen controls When viewing a page with more than 1 application displayed you can switch applications from the splitscreen view to fullscreen view.
6.15 Screen overview 1 2 3 8 Screen item Description 1 Back — On New e Series displays you can press the on-screen << (back) icon to go back to a previous menu. (On New c Series displays use the Back button. 2 Close — On New e Series displays you can press the on-screen X (close) icon to go back to a previous menu. (On New c Series displays use the Back button to back out of the menu structure.
Using list dialogs Screen item Description List dialogs are full-screen menus that display the details for specific types of data, such as Waypoints. 1 Back — On all models you can press the Back button to go back to a previous menu or, on HybridTouch displays you can select the icon on screen. 2 Field — Selecting a text field automatically displays the on-screen keyboard, which can be used to edit the details. 3 Close — On HybridTouch displays you can select this icon to close the menu(s).
6.16 Editing information in dialogs 6.17 Editing numerical settings With the dialog displayed: 1. Select the field you want to edit. The on-screen keyboard is displayed: To edit numerical values in you can either use the Rotary Control, the on-screen numeric adjust control or on-screen numeric keypad to increase or decrease the value. 1 2 3 4 D12567-1 2. Use the on-screen keyboard to make the changes. 3. Use the on-screen keyboard's SAVE key to keep any changes.
6.18 Basic touchscreen operations 6.19 Databar status symbols Placing and moving the cursor using touch The status symbols on the databar confirm whether the appropriate connections to your system have been made. To place or move the cursor around the screen on a touchscreen multifunction display follow the steps below. 1. Touch the screen at any position on the screen to place the cursor there. The symbols show the status for the following: • Radar scanner. • AIS receiver / transceiver.
Symbol Description Symbol Description AIS unit is connected and switched on, but has active alarms. Power steering active. AIS unit is connected and switched on, but the dangerous and lost alarm is disabled. Wind Vane mode is active. Sonar status symbols The sonar status is indicated in the databar. Symbol Description Symbol animated: the sonar module is connected and transmitting. Symbol static: the sonar module is connected but not transmitting.
6.20 Initial set up procedures Adjusting the display brightness Once your display has been installed and commissioned, Raymarine recommends that you perform an initial set up procedure. 1. Press the POWER button once. The Backlight Level control is displayed. 2. Using the rotary control, adjust the brightness level as appropriate. 3. To switch the color palette, from the homescreen select Customize > Display Preferences > Color Palette.
GPS selection You can use an internal or external GPS receiver. • The multifunction display features an internal GPS receiver. • You can also connect an external GPS receiver using SeaTalkng or NMEA 0183. • Use the System Settings menu to enable or disable the internal GPS receiver. Enabling or disabling the internal GPS With the homescreen displayed: 1. Select Set-Up. 2. Select System Settings. 3. Select Internal GPS. 4. Select the On or Off option as appropriate.
New c Series / New e Series
Chapter 7: Managing display data Chapter contents • 7.1 Memory cards overview on page 76 • 7.2 Inserting a memory card or chart card on page 76 • 7.3 Removing a memory card or chart card on page 77 • 7.4 Saving user data and user settings on page 77 • 7.
7.1 Memory cards overview You can use memory cards to archive data such as waypoints, routes, and tracks. Memory cards can be used to archive your data when the system capacity is reached. You can then delete old data from your system, creating capacity for new data. The archived data can be retrieved at any time. You can also use memory cards to backup your data. 7.2 Inserting a memory card or chart card 1. Open the chart card door, located on the front right of the display. 2.
7.3 Removing a memory card or chart card From the homescreen: 1. Select My Data. 2. Select Eject Card. A message is displayed prompting you to select the memory device you want to eject. 3. Select SD1 for a memory card in the top card slot, or SD2 for a memory card in the bottom card slot. 4. Open the chart card door, located on the front right of the display. 5. Push the edge of the card towards the unit, until an audible click is heard.
Erasing waypoints, routes, and tracks from the system Application Setting Affected Bearing mode Note: The following procedure permanently erases selected or ALL waypoints, routes, or tracks stored on the display. BEFORE proceeding, ensure that you backup any data that you want to keep on to a memory card. MOB Data type Variation source With the homescreen displayed: 1. Select My Data. 2. Select Erase from System. 3.
Application Setting Affected System diagnostics External interfaces AIS overlay Internal interfaces NOWRad overlay Software services GPS status GPS screen Compass status Compass screen Application Setting Application Setting Cartography Range rings Affected Affected 2D Chart Use Chart Sync Alarms Application Setting Alarms Anchor alarm Affected Chart orientation Motion mode Timer Vessel offset Alarm clock 3D centre of view Temperature alarm 3D exaggeration Arrival alarm 3D
Application Setting Affected Light sectors Data application Application Setting Data Datapages and content Affected Routing systems Datapage order Caution areas Color theme Marine features Dial color Land features Number of engines Business services Maximum tachometer range Panoramic photos Trim tabs Roads Calibrate trim tabs Additional wrecks Fishfinder application Aerial photo overlay colored seabed areas Application Setting Fishfinder Configure preset frequencies Vessel icon Affected T
7.5 Resetting your system Your system may be reset to its factory default settings if required. There are 2 types of reset operation, both of which affect the current display you are using, AND any networked displays. • Settings reset. • Settings and data reset. Settings reset This option resets your setup menus, page sets, and databar settings to factory default. It will NOT affect your waypoints, routes, or tracks data.
New c Series / New e Series
Chapter 8: Using autopilot control Chapter contents • 8.1 Autopilot control on page 84 • 8.2 Autopilot status symbols on page 85 • 8.
8.1 Autopilot control You can use your multifunction display to control your autopilot. Note: For information on connecting your multifunction display to a Raymarine autopilot system, refer to the documentation that accompanied your autopilot. 1. Select Set-up. 2. Select System Settings. 3. Select Autopilot Control so that On is highlighted. Selecting Autopilot Control will switch the control between On and Off.
8.2 Autopilot status symbols 8.3 Autopilot alarms The autopilot status is indicated in the databar. The autopilot function provides alarms to alert you to situations that require action. Symbol Description Autopilot is in Standby mode. Autopilot is in Track mode. Autopilot is in Auto mode. No autopilot detected. Autopilot alarm active. Your multifunction display shows autopilot alarms, regardless of whether there is active navigation on the system.
New c Series / New e Series
Chapter 9: Using alarms and MOB functions Chapter contents • 9.1 Using Man Overboard (MOB) functions on page 88 • 9.
9.1 Using Man Overboard (MOB) functions Man overboard If you lose a person or object overboard, you can use the Man Overboard (MOB) function to mark the position that the vessel was at when the MOB function was activated. The MOB function is available at all times, regardless of which application is running. MOB can be set to Dead Reckoning or Position mode. Dead Reckoning mode will take into consideration the effects of wind and tides. This usually provides a more accurate course.
9.2 Alarms Alarms alert you to a situation or hazard requiring your attention. You can set up alarms to alert you to certain conditions, such as collision warnings and temperature limits. Alarms are raised by system functions, and also external equipment connected to your multifunction display. When an alarm sounds a message dialog is displayed on your multifunction display and any networked displays. The dialog states the reason for the alarm.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • 2 ft (or equivalent units) to the maximum of the transducer range Guard Zone Off Track The Guard Zone feature in the radar application triggers an alarm when a target is within a specified zone. You can adjust the sensitivity of the alarm. Ensure that the sensitivity is not set too low, or targets may be missed and the alarm will not be triggered.
New c Series / New e Series
Chapter 10: Using waypoints, routes and tracks Chapter contents • 10.1 Waypoints on page 94 • 10.2 Routes on page 98 • 10.3 Tracks on page 102 • 10.
10.1 Waypoints Showing and hiding waypoint groups / symbols A waypoint is a position marked on the screen to indicate a site or a place to navigate to. As well as acting as position markers, waypoints are also the building blocks used to create routes. Common waypoint functions are accessed using the waypoints menu. This can be shown at any time by selecting WPT . From the chart or radar application: 1. Press the WPT button. 2. Select Display Waypoints. 3.
• Restart XTE Placing a waypoint at a known position • Advance Waypoint You can place a waypoint at a specified location using latitude and longitude coordinates: 1. Select WPT. 2. Select Place Waypoint At Lat/Lon. 3. Select the Position field. 4. Enter the Latitude/Longitude position. 5. Select SAVE. 6. You can also add a name for the waypoint and add to a group by selecting the Name and Group fields. • Measure • Build Route • Acquire Target (only available if Radar overlay is switched on.
Note: Selecting WPT from the homescreen will take you to the waypoints list. Cancelling navigation to a waypoint From the chart or radar application: 1. Select the active waypoint. The waypoint context menu is displayed. 2. Select Stop Goto. 3. Alternatively, in the chart application, go to: Menu > Navigate > Stop Goto. Note: Once navigation is no longer active, the waypoint symbol returns to its normal state, and the dashed line between your vessel and the waypoint is removed.
Symbol Type Symbol Type Dolphin Dot Fad Fish Fish (1–star) Fish (2–star) Fish (3–star) Fish trap Hill peak Ledge Lobster Marker Martini Nuns Oil rig Oyster Post Preferred marks Private reef Public reef Reef Reef ball Restriction Rocks Sail boat Route end Route start School of fish Seaweed Shark Skull Small fish Sport fisher Square Swimmer Tank Top mark Tower Trawler Tree Triangle Wreck 2. Select Edit Waypoint. 3. Select the Position field. 4.
1. Select Add New. The on-screen keyboard is displayed. 2. Select the name field. 3. Use the on-screen keyboard to enter the required name for your new waypoint group. 4. select SAVE . 10.2 Routes A route is a series of waypoints typically used to assist with passage planning and navigation. A route is displayed on screen as a series of waypoints linked by a line. Moving waypoints between groups 1. From any application, select WPT. 2. Select View Waypoint List. 3.
2. Select Build Route. The build route menu is displayed. 3. Select a location on screen to be the starting position. 4. Select relevant locations to place subsequent waypoints in order. The route is saved and displayed as each waypoint is placed. 5. When complete select Finish Build. The finish route build pop up message is displayed. 6. Select Follow to immediately follow the route. or 7. Select Edit to change the route name or change the route color. or 8.
• Hide Route 1. Select the route. The route context menu is displayed. 2. Select Advance Waypoint. • Insert Waypoint • Edit Route Note: If the current destination is the last waypoint, the chart advances on to the first waypoint in the route. • Erase Route • Add Route Leg • Acquire Target (only available if Radar overlay is switched on.
Showing or hiding a route From the chart application: 1. Select Menu. 2. Select My Data. 3. Select Display My Data. 4. Select Select Routes To Display. The display routes dialog is displayed. 5. Select the route to switch between Show and Hide. 2. Select Erase Data From System. 3. Select Erase Routes From System. The erase routes from system dialog is displayed. 4. Select Erase All. The confirm delete pop up message is displayed. 5. Select Yes to confirm, or No to cancel the action.
10.3 Tracks A track is an on-screen trail that shows the passage you have taken. This trail is made up of a series of track points which are created automatically. You can save the track to create a permanent record of where you have been • Auto— The track interval is automatically set (Auto will minimize track points whilst maintaining correlation between the track and the actual path followed). • Time— The track points are placed at regular intervals of time.
• Create a route from a track. • Show or hide a track on the chart (only available from the chart application). • Change the name of a track. • Change the color of a track. 10.4 Waypoints, routes and tracks storage capacity The display can store the following quantities of waypoints, routes and tracks Waypoints Selecting a track to review or edit 1. Do one of the following to select the required track: • From the chart application, select a track on screen to display the track context menu.
New c Series / New e Series
Chapter 11: Using the chart Chapter contents • 11.1 Chart application overview on page 106 • 11.2 Chart ranging and panning on page 107 • 11.3 Vessel position and orientation on page 108 • 11.4 Chart views on page 110 • 11.5 Chart context menu on page 111 • 11.6 My Data options on page 112 • 11.7 Navigation options on page 112 • 11.8 Measuring distances and bearings on page 113 • 11.9 Chart vectors on page 113 • 11.10 Current information on page 114 • 11.
11.1 Chart application overview The chart application provides an electronic chart with passage planning and navigation features. It combines 2D and 3D viewpoints and provides a variety of cartographic information regarding your surroundings and charted objects. Typical uses for the chart application include : • Monitor your vessel location and heading. • Interpret your surroundings. It may be possible to use your multifunction display to correlate an NMEA0183 GPS receiver.
Navionics chartplotter sync connection 11.2 Chart ranging and panning You can wirelessly synchronize waypoints and routes between the multifunction display and a tablet or smartphone device. Ranging in and out 1 2 3 The table below shows the Range controls available for each display variant. 4 Rotary Control • New c Series • New e Series Range in and Range out buttons • New c Series Range in and Range out on-screen icons • New e Series D12166-2 1. Multifunction display. 2. Wi-Fi connection.
11.3 Vessel position and orientation Head Up mode displays the chart with your vessel’s current heading upwards. As the heading changes the vessel symbol remains fixed and the chart picture rotates accordingly. Vessel position on the chart display Your current position is represented on screen by the vessel symbol. The symbol used for your vessel will vary depending on the vessel type selected during initial set up of your multifunction display.
the chart in auto range also suspends motion mode. The default setting is relative motion with zero offset. The mode that you select is restored at power up. Auto Range Relative Motion with optional vessel offset Offset Example D12305-1 Auto Range selects and maintains the largest possible scale of chart that will display both the vessel and the target waypoint. Auto range is not available if radar-chart synchronization is on. Zero Offset Setting the motion mode From the chart application: 1.
11.4 Chart views 3D chart view The 3D view can display a range of information to help you navigate. Switching between 2D/3D chart view 1 You can switch between 2D and 3D views. From the chart application: 1. Select Menu. 2. Select Presentation . 3. Select Chart View to switch between 2D or 3D. 2 3 4 5 7 6 8 10 9 000°T 11 2D chart view The 2D chart view can display a range of information to help you navigate.
ii. New e Series — Press and hold the screen and swipe your finger up or down to adjust the pitch. D11755-1 4. To adjust the rotation: i. New c Series — Move the Joystick Left or Right to adjust the pitch ii. New e Series — Press and hold the screen and swipe your finger left or right to adjust the pitch. 11.5 Chart context menu Placing the cursor over an area in the chart application displays a context menu showing the cursors positional data and menu items.
11.6 My Data options 11.7 Navigation options The chart provides features to help you manage your data and help plan your navigation to a chosen location. The chart application provides features to help navigate to a chosen location. The options are found in the My Data menu: Menu > My Data. The navigation options are found in the Navigate menu: Menu > Navigate. • Waypoint List — View and edit waypoints stored on the system. • Route List — View and edit routes stored on the system.
11.8 Measuring distances and bearings 11.9 Chart vectors You can use the databar and context menu information you can use the measure function to measure distances in the chart application. Chart vectors display indicators for heading, COG, wind direction and tide direction. You can determine the distance and bearing: A range of vector graphics can be displayed in the chart application when in 2D chart view.
11.10 Current information 7. To set the animation date to 24 hours ahead of the current date select Next Day. Animated current information The electronic charts may allow animation of the current information current stations. Displaying details of currents From the chart application: 1. Select diamond-shaped current icon. The chart context menu is displayed. 2. Select Current Station. The current graph for the selected current station is displayed.
11.11 Tide information Tide graphs Tide graphs provide a graphical view of tidal activity. Animated tide information 1 The electronic charts may allow animation of the tide information tide stations. Animated tide information is available in the chart application wherever a diamond-shaped symbol with a "T" is displayed: This symbol identifies tide stations and the availability of tide information for the location.
11.12 Chart object information You can display additional information on the chart for cartographic objects, ports, and marinas. 5. Select SEARCH. The search results are displayed. 6. Select an entry in the list to display more information. You can also search for the nearest instance of a particular chart object and search for ports by name.
11.13 Chart presentation • Radar — Overlay radar onto the chart (2D view only). The chart has a number of presentation options which affect the level of detail, types of objects and aspects of its operation. The presentation options available are: • NOWRad — Provides the NOWRad weather radar overlay, without the need to open a separate weather application window (2D view only). • Chart detail — Set the level of object detail shown on the chart.
Radar overlay NOWRad weather overlay You can combine the chart with the radar and MARPA functions to provide target tracking or to help you distinguish between fixed objects and other marine traffic. With a suitable weather receiver connected to your multifunction display, you can overlay NOWRad weather information on the chart display.
4. Select Range Rings so that On is highlighted. Selecting range rings will switch range rings between On and Off. Safe Zone Ring The chart application can display and configure a MARPA / AIS safe zone ring. The safe zone ring shares its configuration with the Radar applications safe zone ring, however can be displayed independently of the safe zone ring in the Radar application. If a MARPA or AIS target will reach the safe zone ring within the time to safe zone selected an alarm is sounded.
3. Select Chart Sync. 4. Select Chart from the list. A tick is placed next to the selected option. 5. Repeat the steps above for each chart instance and if required on each networked multifunction display you want to sync the chart view. Note: You cannot sync to another chart if radar sync is turned on.
11.14 Chart set-up Selecting the chart set-up menu From the chart application: 1. Select Menu. 2. Select Set-up. The Chart Set-up menu is displayed.
Chart set-up menu options The following table describes the various options in the Chart Set-up Menu for your multifunction display. Menu item Description Options Context Menu (Touchscreen displays only) Determines how the context menu is accessed using touch • Touch — touching a chart object opens the context menu. • Hold — Touch and holding on a chart object opens the context menu. Cartography Provides access to the Cartography menu options.
Cartography set-up menu options The following table describes the various options in the Cartography Set-up Menu for your multifunction display. Menu item Description Options Chart Display Determines the level of detail shown on the chart. • Simple • Detailed (default) • Extra Detailed Chart Grid Determines whether grid lines representing longitude and latitude are displayed on the chart: • Off • On (default) • Off — grid lines are NOT displayed. • On — grid lines are displayed.
Menu item Description Options Nav. Marks Symbols Determines which set of navigation mark symbols is used — International, or US. These symbols correspond to paper charts. • International (default) Determines whether the sector of light cast by a fixed beacon is displayed or not. • Off Light Sectors • US • On (default) • Off — sector of light is NOT displayed. • On — sector of light is displayed. Routing Systems Determines whether routing data is displayed or not.
Chapter 12: Using radar Chapter contents • 12.1 Radar overview on page 126 • 12.2 Radar scan speed on page 127 • 12.3 Radar scanner status symbols on page 127 • 12.4 Radar range and image quality on page 128 • 12.5 Radar display overview on page 130 • 12.6 Dual range radar operation on page 131 • 12.7 Radar mode and orientation on page 132 • 12.8 Radar tuning: On-screen gain controls on page 134 • 12.9 Radar adjustments: HD and SuperHD scanners on page 135 • 12.
12.1 Radar overview Radar is used to provide information that can help you to track targets and measure distances and bearings. Radio Detection And Ranging (RADAR) is used at sea to detect the presence of objects (known as ‘targets’) at a distance, and if they are moving, detect their speed. Radar works by transmitting radio pulses, then detecting reflections of these pulses (echoes) from objects in the area and displaying the reflections as targets on your display.
12.2 Radar scan speed 12.3 Radar scanner status symbols SuperHD open array radars with software version 3.23 or above or HD radomes support multiple scan speeds. The radar scanner power mode status is indicated in the databar. Radar scan speed is set up using the Radar Set-up menu.
2. Select Power up Radar to turn the radar on, or Power down Radar to turn the radar off. 3. Select Radar: Tx to start the radar transmitting, or Radar: Stdby to stop the radar transmitting. 12.4 Radar range and image quality Maximum radar range The usable range of the radar is limited by factors such as the height of the scanner, and height of the target.
Rain or Snow Clutter The radar can see echoes from rain or snow. Returns from storm areas and rain squalls consist of countless small echoes that continuously change size, intensity and position. These returns sometimes appear as large hazy areas, depending on the intensity of the rainfall or snow in the storm cell.
12.5 Radar display overview With your radar scanner connected and the radar in transmit mode, the radar picture provides a map-like representation of the area in which the radar is operating. 2 1 3 5 4 6 7 8 9 D6601-3 10 11 12 13 14 15 D12207-2 Item Description 1 Range 2 On-screen controls (Touchscreen multifunction displays only.
that the size of a target on screen is dependent on many factors and may not necessarily be proportional to its physical size. Nearby objects may appear to be the same size as distant larger objects. Note: Colors stated above refer to the default color palette. With experience, the approximate size of different objects can be determined by the relative size and brightness of the echoes. You should bear in mind that the size of each on-screen target is affected by: 12.
Scanner Dual Range mode Operating mode 4 Kw SuperHD Open Array Long SuperHD Short HD Long SuperHD Short HD 12 Kw SuperHD Open Array 12.7 Radar mode and orientation Radar orientation modes The radar can operate in a number of orientation modes to suit different types of navigation. The orientation of the radar refers to the relationship between the radar and the direction that you are travelling in.
Course-Up 1 The default motion mode is “Relative”, with zero offset. N N 2 True Motion (TM) When the motion mode is set to True, fixed radar targets maintain a constant position and moving vessels (including your vessel) travel in true perspective to each other and to fixed landmasses on the screen. As the vessel’s position approaches the edge of the screen, the radar picture is automatically reset to reveal the area ahead.
12.8 Radar tuning: On-screen gain controls Touchscreen multifunction displays provide on-screen access to controls for Gain, Rain and Sea clutter. Gain control Rain control Sea control Note: New c Series controls are accessed by the menu options: Menu > Rain and Menu > Adjust Gain. Enabling and disabling on-screen gain controls You can enable and disable the on-screen gain controls by following the steps below. On a New e Series multifunction display, with the relevant application displayed. 1.
12.9 Radar adjustments: HD and SuperHD scanners You can use the gain presets and other functions to improve the quality of the radar picture. The following settings are available from the Radar menu and apply to HD radomes, HD and SuperHD open array scanners: Menu Item Description Options Auto Gain Mode The radar gain presets enable you to quickly select pre-configured settings to achieve the best picture in different situations.
Adjusting radar anti sea clutter From the radar application, with the required Auto Gain Mode selected: 1. Select Menu. 2. Select Adjust Gain , where shall be the Auto Gain mode already selected. 3. Select Sea: . 4. The Sea clutter slider bar control is displayed. 5. Adjust the Sea clutter slider bar control to the appropriate setting (between 0 and 100%), or 6. Select the Auto box so that a tick is placed in the box for automatic sea clutter control.
12.10 Radar adjustments: non-HD digital radomes You can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-HD digital radomes and are available from the Radar menu: Menu Item Description Options Rain The radar scanner detects echoes from rain or snow. These echoes appear on screen as countless small echoes continuously changing size, intensity and position.
12.11 Radar presentation menu options Function Description Options Dual Range This menu item allows you to turn Dual range mode On and Off. • On • Off Dual Range Channel This menu item allows you to choose long or short channel for dual range.
Function Description Options Data Overlay Set-up This menu item contains a sub-menu which enables you to turn on and select information to display in data cells located on the bottom left of the radar application (Data cells will be displayed in all radar windows).
12.12 Using radar to measure distances, ranges, and bearings When you are using the radar application, you can measure distances, ranges and bearings in a variety of ways.
VRM/EBL context menu The VRM/EBL function includes a context menu which provides positional data and menu items. 1. Position the cursor over the VRM/EBL. 2. Press the Ok button. The radar context menu is displayed. 3. Use the Rotary Control to select Float Center. 4. Press the Ok button. 5. Using the Joystick, move the center position of the circle to the desired position. 6. Press the Ok button to confirm the new position.
12.13 Using radar to track targets and avoid collisions The Guard Zone , VRM/EBL and MARPA functions will help you track targets and avoid collisions. With a radar connected to your multifunction display, you can: • Assess how far away a target is and its bearing (VRM/EBL). • Set an alarm to trigger when a target is within a specified zone (Guard Zone). • Display detailed information on tracked targets (MARPA). • Display the range and bearing of a target.
• The target echo is weak. The target is very close to land, buoys or other large targets. • The target or your own vessel is making rapid manoeuvres. • Choppy sea state conditions exist and the target is buried in excessive sea clutter or in deep swells. • Choppy sea state conditions exist yielding poor stability; own vessel’s heading data is very unstable. • Inadequate heading data.
Vessel vectors (CPA graphics) overview CPA graphics show vectors for your vessel and a selected target. A vector is a line on-screen showing the predicted courses of your vessel and the selected target if you both remain on your present course. These vectors vary in length due to vessel speed and vector length set in the MARPA Set-up menu. 2 1 143°T 28.0kt 0.
12.14 Scanner set-up menu options The Scanner Set-up menu enables you to configure the performance and behavior of your radar scanner.
12.15 Resetting the radar To reset radar settings to defaults follow the steps below: From in the radar application: 1. Select Menu. 2. Select Scanner Set-up. 3. Select Advanced Set-up. 4. Select Reset Advanced. A confirmation pop up message is displayed. 5. Select Yes to confirm reset.
Chapter 13: Using AIS Chapter contents • 13.1 AIS overview on page 148 • 13.2 AIS prerequisites on page 149 • 13.3 AIS context menu on page 149 • 13.4 Enabling AIS on page 150 • 13.5 Displaying AIS vectors on page 150 • 13.6 AIS status symbols on page 151 • 13.7 AIS silent mode on page 151 • 13.8 AIS target symbols on page 152 • 13.9 Displaying detailed AIS target information on page 152 • 13.10 Viewing all AIS targets on page 153 • 13.
13.1 AIS overview AIS Simulator Mode The AIS feature enables you to receive information broadcast by other vessels, and to add these vessels as targets in the chart and radar applications. With an optional AIS unit connected to your system you can: • Display targets for any other AIS-equipped vessels. • Display voyage information being broadcast by these targets, such as their position, course, speed and rate-of-turn.
13.2 AIS prerequisites 13.3 AIS context menu You must have suitable AIS hardware connected to your multifunction display to make use of the AIS functionality. The AIS function includes a context menu which provides AIS target information and menu items. In order to run AIS, you will need: • A receive-only AIS unit or a full AIS transceiver (a unit that sends and receives). • A VHF antenna. • A GPS - to provide position data. • The AIS layer enabled in the chart or radar application, as appropriate.
13.4 Enabling AIS 13.5 Displaying AIS vectors Enabling AIS in the chart application You must have the correct data available before AIS vectors can be displayed. To enable AIS overlay in the chart application the chart view must be set to 2D Menu > Presentation > Chart View. A target is defined as active when it has the following data displayed graphically: From the chart application: 1. Select Menu. 2. Select Presentation. 3. Select Layers. 4. Select AIS: so that On is highlighted.
13.6 AIS status symbols AIS status is indicated by a symbol in the databar. Symbol Description AIS unit is switched on and operating. AIS currently unavailable. AIS unit is switched off, or not connected. AIS unit is in Silent Mode. AIS unit is in Silent Mode, with active alarms. AIS unit is connected and switched on, but has active alarms. AIS unit is connected and switched on, but the dangerous and lost alarm is disabled. Using AIS 13.
13.8 AIS target symbols Your multifunction display shows a range of symbols to represent the different types of AIS target. Target type Description Transmitting target Target is moving or at anchor (Target is not activated, dangerous or lost). Activated target Target activated — that is, AIS vector displayed. Vector line (optional) shows predicted distance travelled within a given time. Selected target Target selected with cursor. Can view detailed data. Symbol 13.
13.10 Viewing all AIS targets 13.11 Using AIS to avoid collisions From the chart application go to Menu > AIS Options You can use the AIS safe zone and safety message functions to help you avoid collisions with other vessels and objects. From the radar application go to Menu > Track Targets > View AIS Lists 1. Select AIS List. A list of all available AIS targets is displayed.
2. Select Track Targets. 3. Select AIS Unit Set-up. 4. Select AIS Safety Messages. Selecting AIS Safety Messages will switch between safety messages On and Off. Displaying safety-critical AIS information From the chart or radar application: 1. Select the AIS target. The AIS target context menu is displayed. 2. Select AIS Data so that On is highlighted. Selecting AIS Data will switch between AIS data On and Off. 13.
13.13 AIS alarms 13.14 Buddy tracking The AIS functions generate a number of alarms to alert you to dangerous or lost targets. The Buddy Tracking feature enables you to add AIS-equipped friends and regular contacts to a “Buddy List” on your multifunction display. As soon as a vessel on your Buddy List sails into the range of your AIS unit, the vessel icon changes to indicate this. In addition to the dangerous target alarm, the system generates an alarm when a dangerous target becomes a lost target i.e.
ii. Select No to save the vessel to your buddy list without entering a name for the buddy vessel. The vessel will now be added to your buddy directory. Adding a vessel to your buddy list from AIS target list 1. If you are in the chart application, goto Menu > AIS Options. 2. If you are in the radar application, goto Menu > Track Targets > View MARPA & AIS Lists. 3. Select View AIS List. The AIS Target List is displayed. 4. Select an AIS target. 5. Select Add Buddy. i.
Chapter 14: Using the fishfinder Chapter contents • 14.1 How the fishfinder works on page 158 • 14.2 Raymarine sonar modules on page 158 • 14.3 Fishfinder introduction on page 159 • 14.4 Transducer bandwidth on page 160 • 14.5 The sonar image on page 160 • 14.6 Fishfinder presets on page 161 • 14.7 Dual / Single frequency fishfinder on page 162 • 14.8 Non-CHIRP (traditional) sonar module frequency controls on page 162 • 14.9 CHIRP sonar module frequency controls on page 163 • 14.
14.1 How the fishfinder works 14.2 Raymarine sonar modules The fishfinder application uses a sonar module and a suitable sonar transducer. The sonar module interprets signals from the transducer and builds up a detailed underwater view. The table below lists Raymarine’s sonar modules and whether CHIRP technology is used. The transducer is located on the bottom of the boat, it sends pulses of sound waves into the water and measures the time it takes for the sound wave to travel to the bottom and back.
14.3 Fishfinder introduction Warning: Sonar operation Fishfinder context menu The fishfinder application includes a context menu which provides fishfinder information and shortcuts to menu items. • NEVER operate the sonar with the vessel out of the water. • NEVER touch the transducer face when the sonar is powered on. • SWITCH OFF the sonar if divers are likely to be within 7.6 m (25 ft) of the transducer.
14.4 Transducer bandwidth 14.5 The sonar image The fishfinder application displays the fishfinder frequency, center frequency or CHIRP mode depending on the connected sonar module and transducer. Interpreting the seabed using sonar Example of CHIRP sonar module in CHIRP mode. It is important to understand how to correctly interpret the seabed structure represented in the fishfinder display. The seabed usually produces a strong echo.
14.6 Fishfinder presets The fishfinder provides you with four preset configurations available from the fishfinder menu. These enable you to quickly select appropriate settings tailored for various situations. Each preset has been configured to provide the best operating parameters for the fishfinder. However, it is possible to manually adjust the presets if necessary.
14.7 Dual / Single frequency fishfinder Dual frequency operation allows the sonar to operate and display 2 frequencies simultaneously. If the preset mode that you are using has two frequencies configured, you can view either one or both of those frequencies in separate windows. Selecting dual frequency view From the fishfinder application: 1. Select Menu. 2. Select Presets. 3. Select Dual. The main fishfinder menu is displayed. 4. Select View Freq. 5.
The graph above depicts an example of the fine tuning (from —50% to +50%) available when the frequency is set to 200 kHz. Tuning the fishfinder frequency (non-CHIRP sonar module) When connected to a non-CHIRP sonar module you can manually tune the fishfinder frequency. From the fishfinder application: 1. select Menu. 2. Select Frequency settings. 3. Select either Tune Freq 1 or Tune Freq 2 as required. The Tune Frequency slider bar is displayed: 14.
Frequency adjustment (CHIRP sonar module in non-CHIRP mode) When using a CHIRP sonar module in CHIRP mode (Low Chirp, Med Chirp or High Chirp) the frequency cannot be adjusted. When using a CHIRP sonar module in a non-Chirp mode (e.g. 50 kHz or 160 kHz) the frequency at which the transducer is transmitting can be adjusted. With the CHIRP sonar module set to a CHIRP mode (e.g. Low Chirp or High Chirp) the CHIRP sonar module will sweep the transducer’s available frequency range in each ping.
14.10 Fishfinder display modes Selecting a fishfinder display mode From the fishfinder application: 1. Select Menu. 2. Select Display Mode. 3. With dual frequency preset set, select Adjust to select which frequency display you wish to change. Selecting Adjust in Dual frequency preset will switch between Frequency 1 and Frequency 2. 4. Select the Select Mode menu item. 5.
Bottom Lock 14.11 Fishfinder range The Bottom Lock function applies a filter to flatten the image of the seabed and make any objects on or just above it easier to discern. This feature is particularly useful for finding fish that feed close to the bottom. The Range and Range Shift functions enable you to change the range of depth displayed by the fishfinder. Bottom Lock is selected for individual fishfinder windows and can replace or appear alongside the standard fishfinder image.
Rotary Control • New c Series • New e Series 14.12 Fishfinder sensitivity settings The Sensitivity settings menu provides access to features and functions which enhance what is displayed on screen. Sensitivity options include: • Gain Range in and Range out buttons Slide the screen Up or Down • New c Series • New e Series (excluding e7 and e7D • New e Series • Gain Mode — Only available when connected to a non-CHIRP sonar module including the internal sonar module.
5. Select Auto. A tick is displayed in the Auto box to signify automatic gain is enabled. Setting the auto gain mode for non-CHIRP sonar modules When using a non-CHIRP sonar module, from the fishfinder application: 1. Select Menu. 2. Select Sensitivity Settings. 3. Select Gain Mode. A list of available auto gain modes is displayed: Setting auto gain using the on-screen controls Touchscreen multifunction displays provide on-screen access to the gain controls. 1.
When connected to a Raymarine sonar module without CHIRP capabilities an automatic setting is available: When in manual mode the slider bar control is shown: • Auto Selecting the frequency for TVG adjustments When connected to a Raymarine CHIRP sonar module, the TVG for frequency 1 and frequency 2 can be changed independently or both at the same time. If connected to a non-CHIRP sonar module adjustments will be made to both frequencies simultaneously. From the fishfinder application: 1. Select Menu. 2.
5. Select Ok to confirm setting and close the numeric adjust control. 14.13 Fishfinder presentation options Fishfinder power The Presentation menu gives you access to features and functions which provide additional on-screen functionality. Presentation options include: The power setting controls the power level of the transducer. Power options: Menu Item Description Options • Auto. This is the default setting.
Menu Item Description • Data Cell 2 Options Allows selection of a data type by category. Data Cell 2 • Select Data Category • On • Select Data Category 14.14 Depth and distance with the fishfinder The fishfinder display provides a number of features to help you determine depths and distances. These features are illustrated and described in more detail below: • Off 1 Select Data Category Allows selection of a data type by category.
14.15 Fishfinder scrolling The fishfinder image scrolls from right to left. You can pause the scrolling or adjust the scroll speed, to ease placing of waypoints or VRMs on-screen. Scroll speed You can adjust the speed at which the fishfinder image scrolls. A faster speed provides more detail which may be useful when you are looking for fish. If you select a slower speed the information remains on the display for longer.
14.16 Fishfinder waypoints 14.17 Fishfinder alarms Placing a waypoint on the fishfinder display enables you to mark a position so that you can return to it later. The display can be configured to provide a number of fishfinder alarms. When a waypoint is placed, its details are added to the waypoint list and a vertical line labelled WPT is displayed on-screen. The waypoints can then be navigated to using the chart application.
14.18 Sounder set–up menu options This section describes the settings you can change using the sounder set up menu: (Menu > Set-up > Sounder Set-up). The set up menu contains settings that are likely to be changed infrequently. Menu Item Description Options Internal Sounder Switch the built in sonar on and off, for use when you have more than one multifunction display with internal sonar. • On • Off Note: Disabled on non-sonar variants. Note: Must be set to Off if an external sonar is connected.
14.19 Transducer set-up menu options The Transducer Set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu Item Description Options Transducer Select the appropriate transducer type from those displayed. Some transducer may be detected by the system automatically. Options available are dependant on the sonar module connected. Speed Transducer Select the appropriate speed transducer from those available.
14.20 Resetting the sonar The reset function restores the unit to its factory default values. Note: Performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible Raymarine multifunction display go to the Fishfinder application page. 2. Select Menu from the side menu. 3. Select Set-up. 4. Select Sounder Set-up. 5. Select Sonar reset. 6. Select Yes to confirm. The unit will now be reset to factory default settings.
Chapter 15: Using the data application Chapter contents • 15.1 Data application overview on page 178 • 15.2 Pre-configured datapages on page 178 • 15.
15.1 Data application overview 15.2 Pre-configured datapages The data application displays system and instrument data on your multifunction display. By default, a pre-configured range of data is displayed in a number of datapages. Each datapage consists of a number of 'cells', each containing a different item of data. The data application enables you to view numeric data generated by the system.
Datapage Default Data Items Engine 2 • Oil Pressure 1 • Coolant Temperature 1 • Coolant Temperature 2 • Oil Pressure 2 • RPM 1 • Trim Tabs • RPM 2 • Total Fuel • Rudder • SOG Engine 3 15.3 Customizing the data application You can customize the data application to show the system and instrument data that you require. In addition to displaying the default, pre-configured datapages in the data application, you can also: • Change the order datapages appear.
Data Category Data Item Distance Log & Trip Digital Dial Graphical Data Category GPS COG SOG Trip COG Ground Log, Trip SOG Heading Navigation Ground Trip 3 Ground Trip 4 Fuel Heading Cursor position (databar and data overlay only.
Renaming a datapage From the data application: 1. Select Menu. 2. Select Edit Page. 3. Select Rename Page. The on screen keyboard is displayed. 4. Enter the new name for the datapage. 5. Select SAVE. Adding a new datapage You can add your own customized datapages to the data application. The total number of datapages including pre-configured pages is 10. From the data application: 1. Select Menu. 2. Select Create New Page. A list of available page layouts is displayed. 3. Select the required page layout.
Datapage and dial colors Datapage color theme and dial colors can be switched between light and dark. Color Theme Dial Color Light Light Light Dark Dark Dark Dark Light Example Resetting all datapages You can reset the datapages in the data application to the factory defaults. 1. Select Menu. 2. Select Reset All Pages. The confirm reset pop up message is displayed. 3. Select Yes to reset or No to cancel the action.
Chapter 16: Using the weather application (North America only) Chapter contents • 16.1 Weather application overview on page 184 • 16.2 Weather application set up on page 184 • 16.3 Weather application display overview on page 185 • 16.4 Weather map navigation on page 188 • 16.5 Weather context menu on page 188 • 16.6 Weather information on page 189 • 16.7 Weather reports on page 189 • 16.8 Animated weather graphics on page 190 • 16.9 Weather application menu options on page 191 • 16.
16.1 Weather application overview 16.2 Weather application set up The weather application overlays historical, live, and forecasted weather graphics on a world map. A number of steps must be completed before you can use the weather application for the first time. The weather application can only be used in North America and its coastal waters. • Your multifunction display must be connected to a Raymarine Sirius weather receiver.
16.3 Weather application display overview Symbol Description Wind — Wind symbols show the current wind direction and strength and can be displayed as either an arrow or a wind barb. Wind arrows indicate speed — the larger the arrow, the greater (stronger) the wind speed. Wind barbs give a more precise indication of wind speed as shown in the wind speed symbols section. The weather application displays a range of graphics to indicate weather conditions and forecast information.
Surface pressure symbols Symbol The weather application uses a range of symbols to represent different surface pressure conditions. Symbol Speed Symbol Speed Symbol Speed 33–37 kts 38–42 kts 43–47 kts 48–52 kts 53–57 kts 58–62 kts 63–67 kts 68–72 kts 73–77 kts 78–82 kts 83–87 kts 88–92 kts 93–97 kts 98–102 kts etc.
Color code Precipitation type Reflectivity Intensity Dark blue Snow (20+ dBz) Light pink Mixed (5 to 19 dBz) Dark pink Mixed (20+ dBz) 3. Select each graphic you want to Show or Hide. 4. Selecting a graphic will switch between Show or Hide. Note: The Wind Vector graphic options are Arrow or Barb. Canadian radar precipitation color codes Canadian radar shows the intensity of precipitation for Canada. Unlike NOWRad, Canadian radar does not show the precipitation type.
16.4 Weather map navigation 16.5 Weather context menu You can move around the weather map and place waypoints. The weather application includes a context menu which provides positional data and the option to view weather reports from the cursor location. When you open the weather application, a world map is displayed. If the system has a position fix for your vessel, the map will be centred on your location.
16.6 Weather information 16.7 Weather reports You can view weather information for: You can view a number of different weather reports to give you a comprehensive view of the weather. • a specific location • a surface observation station (when displayed) • Cities (when displayed) Your multifunction display shows weather reports for: • Tropical statements. • Marine warnings. Viewing weather data at a specific location • Marine zone forecasts.
16.8 Animated weather graphics You can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • NOWRad — weather radar 1 • Wind • Waves • Pressure — surface pressure D12297-1 Item Description 1 Watchbox alert box Viewing watchbox alerts You can view a watchbox alert at any time by following the steps below: From the weather application with a watchbox alert box displayed. 1.
16.9 Weather application menu options The following options are available from the weather application menu: Menu item Description Find Ship Selecting Find Ship will reset the display to show your vessel in the center of the screen. Display Graphics The Display Graphics menu allows to choose what graphics to Show or Hide in the weather application. Menu item Description Options Watchbox Alert The Watchbox Alerts menu allows you to turn alerts Off, or select a range.
16.10 Glossary of weather terms Term Definition Cold front The boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone A large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depression”. Also the name used for a hurricane in the Indian Ocean and Western Pacific. Depression An area of low pressure. Also called a cyclone.
Term Definition Wave cyclone A storm or low pressure centre that moves along a front. Wave period The period is the time gap between successive waves and the longer the period the faster the waves travel.
New c Series / New e Series
Chapter 17: Using the thermal camera application Chapter contents • 17.1 Thermal camera application overview on page 196 • 17.2 Thermal camera image on page 196 • 17.3 Controls overview on page 197 • 17.4 Camera control on page 198 • 17.5 Image adjustments on page 200 • 17.6 System reset on page 201 • 17.
17.1 Thermal camera application overview The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. 17.2 Thermal camera image The thermal camera provides a video image which is shown on your display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Icon Description 17.3 Controls overview Rear-view mode — image is flipped horizontally. The thermal camera application is available on compatible Raymarine multifunction displays and systems. It includes controls for the thermal camera. Zoom setting: 2x zoom. Thermal camera application – hardkey controls c-series / e-series multifunction displays Zoom setting: 4x zoom. Rotary control Zoom image in / out.
17.4 Camera control Panning, tilting, and zooming the thermal image Power up and standby There are 2 ways of controlling the thermal camera using the thermal camera application: When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in Standby mode. In order for the camera to operate, you must bring the camera out of standby mode using the camera controls.
Pausing the thermal camera image Enabling / Disabling point mode With the thermal camera application displayed: 1. Select Menu. 2. Select Pause Image. Point mode is disabled by default. With Stabilization enabled you can also enable point mode at any time by following the steps below. Thermal camera surveillance mode In surveillance mode the camera pans left and right continuously. The camera continues to pan until surveillance mode is disabled, or the camera controls are used to move the camera.
17.5 Image adjustments White-hot thermal image. Adjusting the thermal camera image With the thermal camera application displayed: 1. Select Menu. 2. Select Adjust Contrast. 3. Select the Contrast, Brightness, or Color option as appropriate. 4. Use the rotary control to adjust as required. Thermal camera scene presets Scene presets enable you to quickly select the best image setting for the current environmental conditions.
Enabling thermal camera rear view mode With the thermal camera application displayed: 1. Select Menu. 2. Select Image Options. 3. Select Rear View. 17.6 System reset Resetting the thermal camera Use this procedure to reset the thermal camera. This will realign the home and stow positions, for example if they become misaligned due to heavy weather. 1. Press the HOME button 4 times successively to reset the camera.
17.7 Camera setup Accessing the thermal camera set-up menu With the thermal camera application displayed: 1. Select Menu. 2. Select Camera Set-up. 3. Select Camera Menu. The camera's menu is displayed and can be controlled using the joystick and the OK button. Video setup menu User Programmable Button menu Use this menu to set up the USER button on the JCU. Menu item / Description USER button operation Search settings The USER button will set the camera scene to Search mode.
About / Help menu Menu item / Description Settings / Operation Name Camera Use this option to name the camera. Menu item / Description Settings / Operation Surveillance mode This options enables you to set the scan width and speed when in surveillance mode. Video Icon Help Screens Exit Exit to main menu. This option displays an explanation of the purpose of each of the screen icons. Use the direction controls to cycle through the pages.
New c Series / New e Series
Chapter 18: Using video Chapter contents • 18.
18.1 Video application overview You can view a video or camera source on your multifunction display. The video application enables you to connect a video source directly to your multifunction display, and view the video on the screen. You can also adjust the brightness, contrast, and color of the video image and aspect ratio. PAL / NTSC is selected automatically.
Chapter 19: Using a remote control Chapter contents • 19.1 Remote control connection on page 208 • 19.2 Pairing the remote and configuring the UP and DOWN buttons on page 208 • 19.3 Operating principles on page 209 • 19.4 Customizing the SHORTCUT button on page 209 • 19.5 Remote control functions on page 210 • 19.
19.1 Remote control connection 19.2 Pairing the remote and configuring the UP and DOWN buttons You can control the multifunction display wirelessly using a Raymarine remote control unit. The remote control uses a Bluetooth wireless connection. 1 2 3 D12163-2 1. Multifunction display. 2. Bluetooth connection. 3. Raymarine Bluetooth remote control (for example, RCU-3). To use the remote control you must first: • Enable Bluetooth in the System Settings on the multifunction display.
19.3 Operating principles 19.4 Customizing the SHORTCUT button Remote control operating principles. On your multifunction display, with the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select External Devices. 4. Select Remote Control. 5. Select Customize shortcut key. 6. Select the function that you want to assign to the SHORTCUT key. • Only 1 multifunction display may be operated by a remote control unit at any one time.
19.5 Remote control functions Bu tto n s Arrow buttons Shortcut button Ra n g e or P a ir S e le c t D12051-2 Button Default functions: Range / zoom. Application where function available: Chart Radar Fishfinder Weather Homescreen • Press UP or DOWN arrow for momentary response. • Hold UP or DOWN arrow for continuous response. Open homescreen. Shortcut: Hold Select application in homescreen (in left-to-right, top-to-bottom order). • Press UP or DOWN arrow for momentary response.
19.6 Reconnecting the RCU 1. When you pair the RCU-3 with a multifunction display a wireless connection is established. 2. When you power off the multifunction display it loses its connection with the RCU-3 after 10 minutes. 60 5 55 10 50 15 45 40 Minutes 20 35 30 25 = > 10 Minutes 3. To restore the connection between the 2 units, press and hold any button on the RCU-3 for at least 3 seconds.
New c Series / New e Series
Chapter 20: Using mobile applications Chapter contents • 20.1 Raymarine mobile apps on page 214 • 20.2 Enabling Wi-Fi on page 215 • 20.3 Enabling mobile apps on page 215 • 20.4 Setting up Wi-Fi security on page 216 • 20.
20.1 Raymarine mobile apps • Select the Raymarine Wi-Fi connection from the list of available Wi-Fi networks on your compatible device. Raymarine mobile apps enable viewing and control of your multifunction display via a compatible mobile device, using a Wi-Fi connection. Raymarine currently offers the following mobile apps: • RayView • Enable the relevant type of connection (i.e. Viewing or Remote Control) in the System Settings on the multifunction display.
20.2 Enabling Wi-Fi 20.3 Enabling mobile apps With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Wi-Fi > ON. Raymarine mobile apps must be enabled on your multifunction display before you can stream video or remote control your multifunction display via a tablet or smartphone device. Using mobile applications With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4.
20.4 Setting up Wi-Fi security 20.5 Selecting a Wi-Fi channel You can encrypt the Wi-Fi connection on the multifunction display to prevent unauthorized devices from accessing the connection. The default encryption is WPA2. By default the multifunction display automatically selects an available Wi-Fi channel.
Chapter 21: Media player application Chapter contents • 21.1 Media player connection on page 218 • 21.2 Enabling Bluetooth on page 218 • 21.3 Pairing a Bluetooth media player on page 219 • 21.4 Enabling audio control on page 219 • 21.5 Media player controls on page 220 • 21.6 Media player controls using a remote control on page 220 • 21.
21.1 Media player connection 21.2 Enabling Bluetooth You can use your multifunction display to wirelessly control a Bluetooth-compatible media player (such as a smartphone). With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Bluetooth > On. The media player must be compatible with the Bluetooth AVRCP protocol (version 2.1 or higher). 1 2 3 D12164-2 1. Multifunction display. 2. Bluetooth connection. 3.
21.3 Pairing a Bluetooth media player 21.4 Enabling audio control With the homescreen displayed and Bluetooth turned on: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select New Bluetooth Connection. A message is displayed prompting you to put your media player device into discovery mode. 5. Ensure Bluetooth is enabled on your external media player device and ensure it is ready to be paired. For more information, consult the instructions that accompany the device. 6.
21.5 Media player controls Touchscreen multifunction displays enable you to use the on-screen media player controls to control the audio playing on your external media player. 21.6 Media player controls using a remote control You can control audio wirelessly using a Raymarine remote control unit. 1. Press UP arrow for next track. 1 2. Press DOWN arrow for previous track. 3. Press SHORTCUT button to play/pause audio.
21.7 Unpairing a Bluetooth device If you are experiencing problems when attempting to use a Bluetooth device with the multifunction display it may be necessary to unpair the device (and any other paired Bluetooth devices) and then retry the pairing procedure. With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Connection Manager. 5. Select the media player device in the list. 6. Select Unpair / Forget this device.
New c Series / New e Series
Chapter 22: DSC VHF radio integration Chapter contents • 22.1 Using a DSC VHF radio with your display on page 224 • 22.
22.1 Using a DSC VHF radio with your display You can connect your DSC VHF radio to your multifunction display and show distress message information and GPS position data for other vessels.
Chapter 23: Customizing your display Chapter contents • 23.1 Language selection on page 226 • 23.2 Boat details on page 227 • 23.3 Units set-up on page 228 • 23.4 Time and Date set-up on page 229 • 23.5 Display preferences on page 230 • 23.6 Data cell and databar customization on page 232 • 23.
23.1 Language selection The system can operate in the following languages: English (US) English (UK) Arabic Chinese Croatian Danish Dutch Finnish French German Greek Italian Japanese Korean Norwegian Polish Portuguese (Brazilian) Russian Spanish Swedish Turkish With the homescreen displayed: 1. Select Customize. 2. Select Language. 3. Select from the languages available.
23.2 Boat details You can customize various aspects of the display's functions to make them specific to your vessel. Menu item Description Options Boat Type You can change the appearance of the vessel in the chart application. Select the option that most closely resembles the type and size of your vessel. • Power Cruiser 1 (default) Note: When boat type is selected during the initial set up of the multifunction display the boat type shall determine the datapage configuration in the data application.
23.3 Units set-up You can specify your preference for the units of measurement that will be used in all applications. Menu item Description Options Distance Units The units of measure that will be used in all applications for the display of all values related to distance. • Nautical Miles • Statute Miles • Kilometers Speed Units The units of measure that will be used in all applications for the display of all values related to speed.
23.4 Time and Date set-up You can specify your preference for the way that time and date will appear in all applications. Menu item Description Options Date Format Allows you to specify the preferred format for the display of date information in all applications. • MM:DD:YY (Month, Day, Year) Allows you to specify the preferred format for the display of time information in all applications.
23.5 Display preferences You can specify your preference for general display behavior. Menu item Description Options Key Beep An audible sound can be made each time a button is pressed or the touchscreen is used. • ON (default) If set to On, the cursor will be automatically hidden after a period of no movement. If set to Off, the cursor will persist on the screen until moved. • ON You can set up shared brightness groups (or “zones”) to adjust the brightness on multiple units simultaneously.
• The Share brightness setting must be set to On for all units in the brightness group. • When setting up a brightness group an initial Sync brightness operation must be performed, with all the displays in that group powered on, to configure the display brightness of all units in the group. Setting up shared brightness With the homescreen displayed: 1. Select Customize. 2. Select Display Preferences. 3. Select Shared Brightness. 4. Select the On option for the Shared brightness menu item. 5.
23.6 Data cell and databar customization You can customize the data displayed in on-screen cells with a wide range of data. Customizable data is displayed in the databar, extended databar (HybridTouch displays only) or data cells areas of the screen. The databar, extended databar and data cells are available in all applications.
Data categories Depending on connected devices the categories of data available to display in the data overlay, databar, and expanded databar. Data category Description Options Boat Types of data generated by your vessel. For example, tank levels. • Fresh Water (%) • Grey Water (%) • Black Water (%) • Live Well (%) Depth Depth data. • Depth Distance Types of data related to distance travelled by your vessel. For example, trip distance.
Data category Description Options Environment Environmental-related data. For example, air temperature. • Pressure • Air Temperature • Set & Drift • Apparent Wind Chill • True Wind Chill • Humidity • Dew Point • Sea Temperature GPS GPS-related data. For example, vessel position. • Vessel Position • COG SOG • COG • SOG Heading Heading-related data. For example, locked heading. • Heading • Locked Heading Navigation Types of data related to navigation. For example, bearing to waypoint.
23.7 System set-up menus The system set-up menus enable you to configure your display and connected external devices. The following menus are available: Menu item Description Alarms Enables you to configure all the different types of alarms produced by the display and connected equipment. Pilot Controls Displays the Pilot Control dialog. Only available when a Raymarine autopilot is detected on the system and Autopilot Control is set to On. Audio Controls Displays the audio controls pop-up.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • 2 ft (or equivalent units) to the maximum of the transducer range Guard Zone Off Track The Guard Zone feature in the radar application triggers an alarm when a target is within a specified zone. You can adjust the sensitivity of the alarm. Ensure that the sensitivity is not set too low, or targets may be missed and the alarm will not be triggered.
Ground trip resets menu This menu enables you to resets the chosen ground trip distance counter to zero. Menu item Description Ground Trip 1 Reset Resets the ground trip 1 distance counter to zero. Ground Trip 2 Reset Resets the ground trip 2 distance counter to zero. Ground Trip 3 Reset Resets the ground trip 3 distance counter to zero. Ground Trip 4 Reset Resets the ground trip 4 distance counter to zero.
• Depth. • Speed. • Wind. Typically this exercise is completed as part of the initial installation, or when new equipment is added. If this exercise is NOT completed the system will automatically attempt to resolve data conflicts. However, this may result in the system choosing a source of data that you do not want to use. above must be MDS-compliant. The system can list any products that are NOT compliant. It may be necessary to upgrade the software for these non-compliant products to make them compliant.
Connections menu This menu enables you to connect wireless Bluetooth and Wi-Fi devices to the display. Menu item Description Options Bluetooth Enable or disable Bluetooth on the display. • On • Off (default) Wi-Fi Enable or disable Wi-Fi on the display. • On • Off (default) Connection Manager Provides a list of Bluetooth devices in range. When you highlight a connection in the list and press OK, the following options are available: • Unpair / Forget this device • Audio control On / Off.
Menu item Description should set this option to OFF to ensure that all NMEA-connected units receive heading data from the external heading sensor. Options NMEA Output Settings Allows you to enable or disable the individual NMEA “sentences” that are sent by the multifunction display to any devices connected the NMEA output port.
Menu item Description Options • If you have a Raymarine GPS receiver using SeaTalk or SeaTalkng, it will automatically correlate each time you change the datum on the multifunction display. • If you have a Raymarine GPS receiver using NMEA 0183, or a third-party GPS receiver, you must correlate it separately. It may be possible to use your multifunction display to correlate an NMEA 0183 GPS receiver. From the homescreen go to Set-up > System settings > GPS Set-up > View Satellite Status.
Maintenance menu This menu provides access to systems settings reset and diagnostics. Menu item Description Touchscreen Alignment (HybridTouch displays only) If the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object with your touch. For best results, perform this exercise when your vessel is anchored or moored.
New c Series / New e Series
Chapter 24: Maintaining your display Chapter contents • 24.1 Service and maintenance on page 246 • 24.2 Routine equipment checks on page 246 • 24.3 Cleaning on page 247 • 24.4 Cleaning the display case on page 247 • 24.
24.1 Service and maintenance 24.2 Routine equipment checks This product contains no user serviceable components. Please refer all maintenance and repair to authorized Raymarine dealers. Unauthorized repair may affect your warranty. Raymarine strongly recommends that you complete a number of routine checks to ensure the correct and reliable operation of your equipment. Complete the following checks on a regular basis: • Examine all cables for signs of damage or wear and tear.
24.3 Cleaning 24.4 Cleaning the display case Best cleaning practices. The display unit is a sealed unit and does not require regular cleaning. If it is necessary to clean the unit, follow this basic procedure: 1. Switch off the power to the display. 2. Wipe the display with a clean, soft cloth (a microfibre cloth is ideal). 3. If necessary, use isopropyl alcohol (IPA) or a mild detergent to remove grease marks.
24.5 Cleaning the display screen A coating is applied to the display screen. This makes it water repellent, and prevents glare. To avoid damaging this coating, follow this procedure: 1. Switch off the power to the display. 2. Rinse the screen with fresh water to remove all dirt particles and salt deposits. 3. Allow the screen to dry naturally. 4. If any smears remain, very gently wipe the screen with a clean microfibre cleaning cloth (available from an opticians).
Chapter 25: Troubleshooting Chapter contents • 25.1 Troubleshooting on page 250 • 25.2 Power up troubleshooting on page 251 • 25.3 Radar troubleshooting on page 252 • 25.4 GPS troubleshooting on page 253 • 25.5 Sonar troubleshooting on page 254 • 25.6 Thermal camera troubleshooting on page 255 • 25.7 System data troubleshooting on page 256 • 25.8 Video troubleshooting on page 257 • 25.9 Wi-Fi troubleshooting on page 258 • 25.10 Bluetooth troubleshooting on page 259 • 25.
25.1 Troubleshooting The troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your product this section will help you to diagnose and correct problems in order to restore normal operation.
25.2 Power up troubleshooting Problems at power up and their possible causes and solutions are described here. Problem Possible causes Possible solutions The system (or part of it) does not start up. Power supply problem. Check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. Check that the power source is of the correct voltage and sufficient current.
25.3 Radar troubleshooting Problems with the radar and their possible causes and solutions are described here. Problem Possible causes Possible solutions No Data or No scanner message Radar scanner power supply Check that the scanner power supply cable is sound and that all connections are tight and free from corrosion. Check relevant fuses and breakers. Check power source is of the correct voltage and sufficient current (using voltage booster if appropriate).
25.4 GPS troubleshooting Problems with the GPS and their possible causes and solutions are described here. Problem Possible causes Possible solutions “No Fix” GPS status icon is displayed. Geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another geographic location. GPS connection fault. Ensure that external GPS connections and cabling are correct and fault free. External GPS antenna in poor position.
25.5 Sonar troubleshooting Problems with the sonar and their possible causes and solutions are described here. Problem Possible causes Possible solutions Sonar data not available on multifunction display. Unit power supply fault. Check the unit power supply and cables. Other unit fault. Refer to the instructions supplied with the unit. SeaTalkhs / RayNet network problem. Check that the unit is correctly connected to a Raymarine network SeaTalkhs switch or crossover coupler (as applicable).
25.6 Thermal camera troubleshooting Problems with the thermal camera and their possible causes and solutions are described here. Problem Possible causes Possible solutions Video not displayed. Camera is in Standby mode. The camera will not display video if it is in Standby mode. Use the camera controls (either the thermal camera application or JCU) to “wake” the camera from standby. Problem with the thermal camera video connections.
25.7 System data troubleshooting Aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions Instrument, engine or other system data is unavailable at all displays. Data is not being received at the display. Check the data bus (e.g. SeaTalkng) wiring and connections. Check the overall integrity of the data bus (e.g. SeaTalkng) wiring.
25.8 Video troubleshooting Problems with the video inputs and their possible causes and solutions are described here. Problem Possible causes Possible solutions No signal message on screen (video image not displayed) Cable or connection fault Check that the connections are sound and free from corrosion.
25.9 Wi-Fi troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. Tablet / smartphone does not have a wireless connection established with the multifunction display. Ensure that Wi-Fi is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Wireless Connections > Wi-Fi > On).
25.10 Bluetooth troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. iPhone does not have a Bluetooth connection established with the multifunction display. Ensure that Bluetooth is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Connections > Bluetooth > On).
25.11 Touchscreen troubleshooting Problems with the touchscreen and their possible causes and solutions are described here. Problem Possible causes Possible solutions Touchscreen does not operate as expected Touch lock is enabled Use the Trackpad to turn off the touch lock on the home screen. Screen is not being operated with bare fingers, for example gloves are being worn Bare fingers must make contact with the screen for correct operation. Alternatively you may use conductive gloves.
25.12 Miscellaneous troubleshooting Miscellaneous problems and their possible causes and solutions are described here. Problem Possible causes Possible solutions Display behaves erratically: Intermittent problem with power to the display. Check relevant fuses and breakers. • Frequent unexpected resets. • System crashes or other erratic behavior. Check that the power supply cable is sound and that all connections are tight and free from corrosion.
New c Series / New e Series
Chapter 26: Technical support Chapter contents • 26.1 Raymarine customer support on page 264 • 26.
26.1 Raymarine customer support 26.2 Third-party support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and email. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Contact and support details for third-party suppliers can be found on the appropriate websites. Web support Navionics www.navionics.
Chapter 27: Technical specification Chapter contents • 27.
27.1 Technical specification e7 / e7D Physical specifications Dimensions Dimensions • Height (NOT including bracket): 222 mm (8.74 in.) • Height (NOT including bracket): 145 mm (5.71 in.) • Height (including bracket): 256 mm (10.08 in.) • Height (including bracket): 180 mm (7.09 in.) • Depth (NOT including cables): 69 mm (2.72 in.) • Depth (NOT including cables): 64 mm (2.52 in.) • Depth (including cables): 160 mm (6.29 in.) Weight (bare unit) e7D e125 / c125 • 3.320 kg (7.32 lb.
Resolution 800 x 480 pixels (WVGA) Antenna Ceramic chip Viewing angle • Left / Right: 70 degrees Accuracy • Without SBAS: <= 15 metres 95% of the time • Top / Bottom: 70 / 50 degrees • With SBAS: <= 5 metres 95% of the time e95 / e97 / c95 / c97 Display specification Size 9 in.
New c Series / New e Series
Chapter 28: Spares and accessories Chapter contents • 28.1 Transducer accessories on page 270 • 28.2 Cables on page 270 • 28.3 e7 e7D spares on page 271 • 28.4 e7 / e7D Service spares on page 271 • 28.5 e95 / e97 / c95 / c97 spares on page 272 • 28.6 e95 / e97 / c95 / c97 Service spares on page 272 • 28.7 e125 / e127 / c125 / c127 spares on page 273 • 28.
28.1 Transducer accessories Item Part number Notes P48 sonar transducer A102140 Transom mount. P58 sonar transducer A102138 Transom mount. 1 m (3.28 ft) Minn Kota transducer adaptor cable A62363 Only for direct connection to sonar variant multifunction display. 0.5 m (1.64 ft) transducer adaptor cable E66066 For connecting any 600 watt sonar module-compatible sonar transducer directly to a sonar variant multifunction display. 28.
28.3 e7 e7D spares Item Part number Trunnion (bracket) mount kit A62358 Documentation pack R62378 Flush mount panel set R62376 Front bezel R62377 Suncover R62365 Spares and accessories 28.4 e7 / e7D Service spares Notes Service spares are only available to service dealers.
28.5 e95 / e97 / c95 / c97 spares Service spares are only available to service dealers. Item Part number c/e series trunnion kit R70001 Item Part number c/e series front bezel R7004 Dust cap kit R62366 c/e series suncover R70005 Flexi pack c/e 9” R70081 c/e/ series rear bezel R70027 Internal seal pack c/e 9” R70083 c.
28.7 e125 / e127 / c125 / c127 spares Item Part number c/e series trunnion kit R70002 c/e series front bezel R7006 Item Part number c/e series suncover R70007 Dust cap kit R62366 c/e/ series rear bezel R70028 Flexi pack c/e 12” R70082 c.
Item Part number LCD assembly non-touch c12 R70019 LCD assembly touchscreen e12 R70021 274 Notes New c Series / New e Series
Appendix A NMEA 0183 sentences The display supports the following NMEA 0183 sentences. These are applicable to NMEA 0183 and SeaTalk protocols.
Appendix B NMEA 2000 sentences The display supports the following NMEA 2000 sentences. These are applicable to NMEA 2000, SeaTalkng and SeaTalk 2 protocols.
Appendix C Connectors and pinouts Pin Signal Power, data, and video connector 9 Screen 10 Not connected 4 9 1 8 10 2 Note: Use only Raymarine RayNet cables when connecting SeaTalkhs devices. 7 11 3 6 5 SeaTalkng connector D12186-1 Item Remarks Identification PWR / NMEA / Video Connector type 11 pin twist-lock Current source to network No current sourced for external devices Current sink from network • PSU: Main Power input. 6 • Video: No power required for interface.
New c Series / New e Series
www.ra ym a rin e .
