N e w a S e r ie s N e w c S e r ie s N e w e S e r ie s Ins ta lla tion a nd ope ra tion ins tructions En g lis h Da te : 10-2012 Docume nt numbe r: 81337-5-EN © 2012 Ra yma rine UK Limite d
Trademark and patents notice Autohelm, hsb2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalkNG, SeaTalkHS and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.
Contents Chapter 1 Important information............................... 9 4.8 Fastheading connection............................................. 50 TFT Displays ....................................................................9 4.9 SeaTalkng connections............................................... 50 Water ingress ................................................................. 10 Disclaimers .................................................................... 10 4.10 SeaTalk connection ........
Chapter 10 Using alarms and MOB functions ................................................................. 101 14.6 AIS status symbols................................................ 165 10.1 Using Man Overboard (MOB) functions .................. 102 14.8 AIS target symbols ................................................ 166 10.2 Alarms.................................................................. 103 14.9 Displaying detailed AIS target information ............... 166 14.
Chapter 19 Using the thermal camera application............................................................... 219 27.2 Power up troubleshooting ...................................... 275 19.1 Thermal camera application overview ..................... 220 27.4 GPS troubleshooting ............................................. 277 19.2 Thermal camera image.......................................... 220 19.3 Controls overview.................................................. 221 27.5 Sonar troubleshooting .
New a Series / New c Series / New e Series
Chapter 1: Important information Warning: Product installation and operation This product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. Warning: Potential ignition source This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks).
Water ingress Water ingress disclaimer Although the waterproof rating capacity of this product meets the IPX6 standard, water intrusion and subsequent equipment failure may occur if the product is subjected to commercial high-pressure washing. Raymarine will not warrant products subjected to high-pressure washing. Disclaimers This product (including the electronic charts) is intended to be used only as an aid to navigation. It is designed to facilitate use of official government charts, not replace them.
1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Industry Canada (Français) Pixel defect policy In common with all TFT units, the screen may exhibit a few wrongly-illuminated (“dead”) pixels. These may appear as black pixels in a light area of the screen or as colored pixels in black areas.
New a Series / New c Series / New e Series
Chapter 2: Handbook information Chapter contents • 2.1 Handbook information on page 14 • 2.2 Product information on page 15 • 2.3 Handbook illustrations on page 16 • 2.4 Handbook conventions on page 17 • 2.
2.1 Handbook information This handbook contains important information regarding your multifunction display. The handbook is for use with the following Raymarine multifunction displays: Additional handbooks Description Part number SeaTalkng 81300 reference manual • New a Series • New c Series • New e Series About this handbook This handbook describes how to operate your multifunction display in conjunction with compatible electronic cartography and peripheral equipment.
2.2 Product information The following Raymarine multifunction display variants are available Nonsonar variant Sonar variant a65 (E70076) a67 (E70077) Series Controls • Bluetooth. New a Series Touchscreen only e7 (E62354) e7D (E62355) Features • Internal GPS. • Bluetooth. New e Series HybridTouch (Touchscreen and physical buttons) • Wi-Fi • NMEA 0183 • NMEA 2000 (via SeaTalkng) • Internal GPS. • Video input. c95 (E70011) c97 (E70012) • Bluetooth.
2.3 Handbook illustrations The illustrations and screenshots used in this handbook may differ slightly from your display model. The illustration of the multifunction display below is used throughout this manual and unless otherwise stated can apply to all variants of multifunction display (i.e. New a series, New c Series and New e Series).
2.4 Handbook conventions The following conventions are used throughout this handbook when referring to: Type Icons Example Convention The term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: • Touch — Press your finger on the icon to select. • Physical buttons — Use the Joystick to highlight the icon and press the Ok button.
Waypoint (MOB) button / icon Depending on the multifunction display variant there will be either a Waypoint (MOB) button or an on-screen icon. WPT button • New c Series • New e Series WPT icons • New a Series Throughout this manual the term: Select WPT, refers to pressing the physical WPT button or pressing the on-screen WPT icon.
2.5 Touch and non-touch operations This handbook applies to New a Series, New c Series and New e Series multifunction displays. All features and functions can be accessed using physical buttons (non-touch) on New c Series and New e Series displays or by using the touchscreen on New a Series and New e Series displays. This handbook uses icons throughout to identify whether a particular task is a touch or a non-touch operation.
New a Series / New c Series / New e Series
Chapter 3: Planning the installation Chapter contents • 3.1 System integration on page 22 • 3.2 Installation checklist on page 26 • 3.3 System Limits on page 26 • 3.4 Multiple data sources (MDS) overview on page 27 • 3.5 Identifying your display variant on page 27 • 3.6 Networking constraints on page 28 • 3.7 Typical systems on page 29 • 3.8 System protocols on page 32 • 3.9 Data master on page 33 • 3.10 New a Series parts supplied on page 33 • 3.
3.1 System integration Your multifunction display is compatible with a wide range of marine electronics devices. 1 2 3 5 4 P IT L O 7 6 8 SMARTPILOT RAY240 9 17 10 11 18 12 13 15 14 16 21 19 20 22 D12244-1 The display uses a number of protocols to transfer data between the various devices in your system.
Item Device Type Maximum quantity Suitable Devices Connections 5 Instruments — Raymarine As determined by SeaTalkng bus bandwidth and power loading. SeaTalk (via optional SeaTalk to SeaTalkng converter): SeaTalk, SeaTalkng. • ST40 Wind, Speed, Depth, Rudder, or Compass. • ST60+ Wind, Speed, Depth, Rudder, or Compass. • i40 Wind, Speed, Depth, or Bidata. SeaTalkng: • ST70. • ST70+. • ST70+ keypads. • i50 Depth, Speed, or Tridata • i60 Wind, CH Wind • i70.
Item Device Type Maximum quantity Suitable Devices Connections 12 Engine interface — third-party 1 Third-party NMEA 2000 interfaces. NMEA 2000 (via optional DeviceNet adaptor cables). 13 Transducers and sensors — Raymarine 1 Analog transducers: SeaTalkng (via optional transducer pods). • Wind. • Speed. • Depth. 13 Transducers and sensors — Airmar 1 • DT800 Smart Sensor. SeaTalkng (via optional transducer pods). • DST800 Smart Sensor. • PB200 weather station.
Item Device Type Maximum quantity Suitable Devices Connections 19 Fishfinder (Sonar Module) — Raymarine 1 • CP450C SeaTalkhs. • DSM30. • DSM300. 20 Radar — Raymarine 1 All Raymarine Non-HD Digital Radomes and HD or SuperHD radar scanners. SeaTalkhs. Note: Please ensure your radar scanner is using the latest software version. 21 Thermal camera — Raymarine 1 All Raymarine thermal cameras. SeaTalkhs (for control), BNC connector (for video).
3.2 Installation checklist 3.3 System Limits Installation includes the following activities: The following limits apply to the number of system components that can be connected in a Raymarine multifunction display system. Installation Task 1 Plan your system. 2 Obtain all required equipment and tools. 3 Site all equipment. 4 Route all cables. 5 Drill cable and mounting holes. 6 Make all connections into equipment. 7 Secure all equipment in place. 8 Power on and test the system.
3.4 Multiple data sources (MDS) overview 3.5 Identifying your display variant Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. • Speed. To discover which model display you have follow the steps below: From the homescreen: 1. Select Set-up. 2. Select Maintenance. 3. Select Diagnostics.
3.6 Networking constraints New a Series, New c Series and New e Series displays can be networked together and can also be networked to Raymarine’s E-Series Widescreen displays and G-Series systems. Caution is advised when networking a New a Series, New c Series or New e Series to a network containing a E-Series Widescreen display or when connecting to a G-Series system as there are networking constraints and restrictions which apply.
3.7 Typical systems The illustrations below show examples of possible system configurations, for more details on compatible devices please refer to the System integration section. Note: In the examples below the multifunction display(s) could be any of the following: • New a Series • New c Series • New e Series Example: Basic system 2 1 3 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkng D12245-2 1. Raymarine Multifunction display. 2. Raymarine network switch. 3. Raymarine radar scanner.
Example: Basic system with sonar variant display 1 2 3 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkng D12589-1 1. Multifunction display 2. Sonar transducer. 3. Radar scanner. 4. SPX course computer. 5. SeaTalkng pilot controller. Example: Basic system with non-sonar variant display 2 1 3 4 5 SMARTPILOT SeaTalkhs / RayNet SeaTalkng D12590-1 1. Multifunction display. 2. Sonar module. 3. Sonar transducer. 4. SPX course computer. 5. SeaTalkng pilot controller.
Example: Expanded system 5 SeaTalkhs / RayNet 12 6 7 4 8 9 SeaTalkng 3 SeaTalkng 2 SeaTalkng 1 SeaTalkng 10 15 SeaTalkhs / RayNet 12 DeviceNet 14 12 13 11 SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkhs / RayNet D12247-2 1. Radar scanner. 2. Weather sensor. 3. Sirius weather receiver. 4. Sonar module. 5. SeaTalkng Pilot controller. 6. SeaTalkng Instrument display. 7. AIS receiver / transceiver. 8. Audio system. 9. Smartphone / tablet. 10. DeviceNet spur (for NMEA 2000 devices). 11.
3.8 System protocols Your Multifunction Display can connect to various instruments and displays to share information and so improve the functionality of the system. These connections may be made using a number of different protocols. Fast and accurate data collection and transfer is achieved by using a combination of the following data protocols: information is passed in ‘sentences’, each of which has a three letter sentence identifier.
3.9 Data master 3.10 New a Series parts supplied Any system containing more than one networked multifunction display must have a designated data master. The following items are supplied with your a65 / a67 multifunction display. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
3.11 e7 / e7D Parts supplied The parts shown below are supplied with the e7 / e7D multifunction display. 3.12 New c Series and New e Series parts supplied The parts shown below are supplied with the New c Series and New e Series (Excluding e7 and e7D) multifunction displays. 5 4 3 4 2 1 3 6 2 9 5 6 1 7 8 7 D12170-2 1. Sun cover. D12248-1 2. Front bezel. 1. Sun cover. 3. Multifunction display. 2. Front bezel. 4. Rear bezel (required for trunnion bracket mounting). 3.
3.13 Tools required for installation 1 2 3 6 4 7 5 8 D12171-1 1. Power drill. 2. Jigsaw. 3. Pozidrive screwdriver. 4. Adhesive tape. 5. Drill bit for trunnion bracket mounting. 6. File. 7. Hole saw for flush mounting (For hole saw size refer to your product’s mounting template). 8. Drill bit for flush mounting.
New a Series / New c Series / New e Series
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 38 • 4.2 Connections overview on page 39 • 4.3 Power connection — New a Series on page 40 • 4.4 Power connection — New c Series and New e Series on page 41 • 4.5 Network connections on page 43 • 4.6 GPS connection on page 49 • 4.7 AIS connection on page 49 • 4.8 Fastheading connection on page 50 • 4.9 SeaTalkng connections on page 50 • 4.10 SeaTalk connection on page 52 • 4.
4.1 General cabling guidance Cable types and length It is important to use cables of the appropriate type and length • Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run. Routing cables Cables must be routed correctly, to maximize performance and prolong cable life.
4.2 Connections overview 0 Details of the connections available on Raymarine multifunction displays are shown below.
0 4.3 Power connection — New a Series 0 0 0 0 0 0 0 0 4 The following restrictions apply to any extension to the power cable: 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 • Cable must be of a suitable gauge for the circuit load. 0 0 0 • Each unit should have its own dedicated power cable wired back to the distribution panel. 2 3 5 Cable extension Total length (max) Supply voltage Cable gauge (AWG) 0–5 m (0–16.4 ft) 12 V 18 5–10 m (16.4–32.8 ft) 12 V 14 10–15 m (32.8–49.
4.4 Power connection — New c Series and New e Series Power cable The display is supplied with a combined power and data multi cable, this can be extended if required. Power cables available 5 4 1 Cable Part number 1.5 m (4.9 ft) Straight power and data cable R62379 1.5 m (4.9 ft) Right angled power and data cable R70029 Notes 2 3 Cable extension 7 The following restrictions apply to any extension to the power cable: 6 • Cable must be of a suitable gauge for the circuit load.
Sharing a breaker Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. - + 1 2 3 4 4 D11637-2 1 Positive (+) bar 2 Negative (-) bar 3 Circuit breaker 4 Fuse Where possible, connect individual items of equipment to individual circuit breakers. Where this is not possible, use individual in-line fuses to provide the necessary protection.
4.5 Network connections You can connect a number of digital devices to your multifunction display using the Network connector(s) at the rear of the unit. A typical network of digital devices may include: • Up to 6 Raymarine multifunction displays. • SeaTalkhs or RayNet digital devices such as a sonar module and radar scanner. • Ethernet IP cameras. Note: Your multifunction display includes the following network connectors: • e7, e7D, a65 and a67 = 1 x SeaTalkhs / RayNet connector.
Network cable connector types Cable Part number There are 2 types of network cable connector — SeaTalkhs and RayNet. 10 m (32.8 ft) SeaTalkhs patch cable E06056 15 m (49.2 ft) SeaTalkhs patch cable A62136 20 m (65.6 ft) SeaTalkhs patch cable E06057 SeaTalkhs connector — used for connecting SeaTalkhs devices to a Raymarine network switch via SeaTalkhs cables. RayNet connector — used for connecting Raymarine network switches and SeaTalkhs devices to the multifunction display via RayNet cables.
Radar connected using crossover coupler 1. Radar scanner 2. Multifunction display rear connector panel. 3. SeaTalkhs crossover coupler. 4. RayNet to SeaTalkhs network cable. 5. Connection to power supply — Open array scanners require a VCM (Voltage Converter Module). 1 Note: The connector on the free end of the radar cable does NOT have a locking mechanism. 2 4 3 5 D12253-1 Radar cable extension For longer cable runs a radar power and data digital cable extension is required.
Digital radar cables Sonar module connection You will need a dedicated radar power and data digital cable and SeaTalkhs network cables to connect your scanner to your system. Connection Required cable Radar scanner to power supply and Raymarine network switch. Power and data digital cable. For longer cable runs, extensions are available in a variety of lengths. Raymarine network switch to multifunction display.
600 watt sonar-compatible sonar transducer connection via optional adaptor — Sonar variant multifunction displays 1 2 3 Sonar variant multifunction displays The table below details which multifunction display variants feature a built-in sonar module and can be connected directly to compatible sonar transducers. Sonar variants Non-sonar variants a67 a65 e7D e7 c97 c95 c127 c125 e97 e95 e127 e125 D12257-1 1. Rear connector panel of multifunction display (Sonar variant). 2.
used in conjunction with the multifunctional display to control the thermal camera if required. • “Dual payload” thermal cameras include 2 independent lenses; 1 for thermal (infrared) and 1 for visible light. If you only have 1 display you should only connect the video cable labelled “VIS / IR” (visible light / infrared) to the display. If you have 2 or more displays you should connect 1 cable to each display.
4.6 GPS connection 4.7 AIS connection Depending on display variant, your multifunction display may include an internal GPS receiver. If required the multifunction display can also be connected to an external GPS receiver, using SeaTalkng or NMEA 0183. A compatible AIS can be connected using SeaTalkng or NMEA 0183. Connection using SeaTalkng 2 1 GPS connection — SeaTalkng 1 2 SeaTalkng D12263-1 1. Multifunction display. SeaTalkng D12261-1 2. SeaTalkng AIS receiver / transceiver. 1.
S M A R T P I L O 4.8 Fastheading connection 4.9 SeaTalkng connections If you wish to use MARPA (radar target acquisition) functions on your multifunction display you need either: The display can connect to a SeaTalkng system. • An autopilot connected to the multifunction display via SeaTalkng or NMEA 0183. The compass is connected to the course computer and calibrated via the pilot control head; or: • A Raymarine or third-party fastheading sensor connected to the multifunction display via NMEA 0183.
SeaTalkng cabling components Description Part No SeaTalkng SeaTalkng to bare ends 3 m (9.8 ft) spur A06044 SeaTalkng Power cable A06049 SeaTalkng Terminator A06031 SeaTalkng T-piece A06028 Provides 1 x spur connection SeaTalkng 5–way connector A06064 Provides 3 x spur connections SeaTalk to SeaTalkng converter E22158 Allows the connection of SeaTalk devices to a SeaTalkng system.
4.10 SeaTalk connection 4.11 NMEA 0183 connection You can connect SeaTalk devices to your multifunction display using the optional SeaTalk to SeaTalkng converter. NMEA 0183 devices can be connected to New c Series and New e Series multifunction displays using the power and data cable. Note: New a Series does not support connection of NMEA 0183 devices. 3 1 SeaTalkng SeaTalk SeaTalkng 2 D12265-1 1. SeaTalk device. 2. SeaTalk to SeaTalkng converter. 3. Multifunction display.
4.12 NMEA 2000 connection Port Input / output Positive (+) / negative (-) * * Output Positive The display can receive data from NMEA 2000 devices (e.g. data from compatible engines). The NMEA 2000 connection is made using SeaTalkng and appropriate adaptor cables.
4.13 Camera / Video connection 4.14 Camera / video in-out connection A camera or a video device can be connected directly to New c Series and New e Series multifunction displays using the video connector on the power and data cable. A camera / video device or external display can be connected to New e Series multifunction displays (excluding the e7 / e7D) using the dedicated video in/out connector. Note: Video devices cannot be directly connected to New a Series multifunction displays.
Connector type BNC (female) Output resolution 720p 4.15 Bluetooth connections Remote control connection Video cables The following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays. Part number Description R70003 e-series accessory video cable Notes You can control the multifunction display wirelessly using a Raymarine remote control unit. The remote control uses a Bluetooth wireless connection. 1 2 3 D12163-2 1.
• Enable Bluetooth in the System Settings on the multifunction display. 4.16 WiFi connections • Enable Bluetooth on the media player device. Raymarine mobile app connection • Pair the media player device with the multifunction display. You can use compatible tablet and smartphone devices as a wireless repeat display or remote control for your multifunction display. • Enable Audio Control in the System Settings on the multifunction display.
Chapter 5: Location and mounting Chapter contents • 5.1 Selecting a location on page 58 • 5.2 Mounting - New a Series on page 59 • 5.
5.1 Selecting a location 1 Warning: Potential ignition source 2 6 This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). 250 (9.8 mm 4 in ) 200 (7.8 mm 7 in ) mm 500.7 in) (19 300 (11 mm .8 i n) 350 (13 mm .8 i n) General location requirements mm 700.5 in) 7 (2 When selecting a location for your display it is important to consider a number of factors.
5.2 Mounting - New a Series Viewing angle 00000 00000 A B Prevailing conditions 000 C The weather and location of the vessel can affect the GPS performance. Typically calm clear conditions provide for a more accurate GPS fix. Vessels at extreme northerly or southerly latitudes may also receive a weaker GPS signal. GPS antenna mounted below decks will be more susceptible to performance issues related to the prevailing conditions.
• Attached the front bezel. D12585-1 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Drill or knock out the 4 mounting holes on the unit 0 00 0 0 D12578-1 1. Mark the location of the mounting bracket screw holes on the chosen mounting surface. 2. Drill holes for the screws using a suitable drill, ensuring there is nothing behind the surface that may be damaged. 3.
5.3 Mounting - New c Series and New e series Viewing angle 000 000000 000 ensuring that the clips along the bottom edge of the bezel latch into position. 000000 B C 000 A 000000 000 000000 D 000 000 D12268-1 D12586-1 4. Ensure the bezel is correctly aligned with the display, as shown. 5. Apply firm but even pressure to the bezel along the: i. Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position. ii.
1. Remove the front bezel. Refer to the separate instructions provided for that procedure. 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Fix the appropriate cutting template supplied with the product, to the selected location, using masking or self-adhesive tape. 3. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. 4.
ensuring that the clips along the bottom edge of the bezel latch into position. Before mounting the unit ensure that you have: • Selected a suitable location. • Identified the cable connections and route that the cables will take. • Attach the front bezel. D12274-1 4. Ensure the bezel is correctly aligned with the display, as shown. 5. Apply firm but even pressure to the bezel along the: i.
New a Series / New c Series / New e Series
Chapter 6: Getting started Chapter contents • 6.1 Display power on page 66 • 6.2 New a Series Controls on page 66 • 6.3 e7 / e7D Controls on page 67 • 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls on page 67 • 6.5 Hybridtouch overview on page 69 • 6.6 Touchscreen overview on page 69 • 6.7 Homescreen overview — New a Series on page 70 • 6.8 Homescreen overview — New c Series / New e Series on page 70 • 6.9 System checks on page 71 • 6.
6.1 Display power 6.2 New a Series Controls Powering the display on 1. Press and hold the POWER button until the Raymarine logo appears. 2. Select Accept to acknowledge the disclaimer message. 1 Powering the display on 1. Press and hold the POWER button until the Raymarine logo appears. 2. Press the OK button to accept the disclaimer message. 2 3 D12577-1 Powering the display off 1. Press and hold the POWER button until the countdown reaches zero.
6.3 e7 / e7D Controls 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls 1 2 1 2 3 3 4 4 5 5 6 6 7 7 D12179-1 8 1. Touchscreen — you can touch the screen to operate many common functions, including all menu operations (HybridTouch multifunction displays only). 11 10 9 2. Menu — accesses menus. Press again to close menus. 3. UniControl — provides a joystick and rotary control and an OK button for using menus and applications. 4.
D7366_3 The cursor appears on the screen as a white cross. WPT D7369-2 D7368_2 1 If the cursor has not been moved for a short period of time, it changes to a circle with a cross in it, to make it easier to locate on the screen. The cursor is context-sensitive. When it is placed over an object such as a waypoint or chart feature, it changes color and a label or information associated with the object is displayed.
6.5 Hybridtouch overview 6.6 Touchscreen overview If your multifunction display features Hybridtouch, this enables you to operate the unit using the touchscreen and the physical keys. The touchscreen provides an alternative to using physical buttons to control your multifunction display. All functions can be accessed using the touchscreen. However, there may be situations (such as rough sea conditions) when it is not appropriate to use the touchscreen.
6.7 Homescreen overview — New a Series 6.8 Homescreen overview — New c Series / New e Series The homescreen provides a central point of access to your display's range of applications. The homescreen provides a central point of access to your display's range of applications. • The homescreen also provides quick access to your data (waypoints, routes, and tracks). • The homescreen also provides quick access to your data (waypoints, routes, and tracks).
6.9 System checks GPS Check GPS selection You can use an internal (if available) or external GPS receiver. 2 • Your multifunction display may feature an internal GPS receiver. • You can also connect an external GPS receiver using SeaTalkng or NMEA 0183. 3 4 • Where appropriate use the System Settings menu to enable or disable the internal GPS receiver.
3. Select Radar so that Transmit is highlighted. The radar scanner should now be transmitting and receiving. 4. Check that the radar screen is operating correctly. Adjusting the bearing alignment Once you have checked the bearing alignment you can proceed and make any required adjustments. With the radar application displayed: 1. Select Menu. 2. Select Scanner Set-up . 3. Select Advanced. 4. Select Bearing Alignment. Selecting Bearing Alignment displays the numeric adjust control. 5.
3. Select Transducer Set-Up. 4. Select Transducer. A list of transducers is displayed. 5. Select the transducer you want to use. Checking the sonar Panning and tilting, and the thermal image On a New e Series multifunction display you can pan and tilt the thermal camera image using the touchscreen. Move your finger up and down the screen to tilt the camera up or down. Sonar checks are made using the fishfinder application. 1. Select the fishfinder page.
6.10 Enabling autopilot functions 6.11 Enabling AIS functions With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Autopilot Control so that On is highlighted. Selecting Autopilot Control switches the control On and Off. 4. Select Backto return to the System Settings menu. 5. Select Pilot Controls. If this menu option is disabled, no autopilot has been found. Check the physical connections, then repeat steps 1 to 5 above. 6.
6.12 Language selection 6.13 Pages The system can operate in the following languages: Pages are used to display applications. English (US) English (UK) Arabic Chinese Croatian Danish Dutch Finnish French German Greek Italian Japanese Korean Norwegian Polish Portuguese (Brazilian) Russian Spanish Swedish Turkish With the homescreen displayed: 1. Select Customize. 2. Select Language. 3. Select from the languages available. Pages are displayed and accessed on the homescreen.
Changing an empty page With the homescreen displayed: 1. Select Customize. 2. Select Homescreen. 3. Select Edit Page. 4. Select an empty page icon (labelled “Customize”). The Customize menu options are displayed. 5. Select the appropriate page layout (for example, “Splitscreen”). 6. Select the application(s) you want to display on the page, either by selecting the relevant menu item or dragging it over to the displayed page. 7. Select Finish. The Rename Page dialog is displayed. 8.
6.15 Splitscreen controls When viewing a page with more than 1 application displayed you can switch applications from the splitscreen view to fullscreen view. Example 1 — Splitscreen page Selecting the active window — e7 / e7D When viewing a splitscreen page you can select the active application and view it fullscreen on an e7 / e7D with the touch lock enabled by following the steps below. With a page featuring multiple applications displayed: 1. Press the Menu button. 2. Select Cycle application.
6.16 Screen overview 1 2 1 2 3 3 8 4 7 4 6 5 D12196-1 Screen item Description 1 Home • New a Series — Select the on-screen Home icon to access the homescreen. D12281-2 Screen item Description 1 Back — On touchscreen displays (New e Series and New a series) you can press the on-screen << (back) icon to go back to a previous menu. (On New c Series displays use the Back button.
Screen item Description Screen item Description 1 Back 3 Close — On Touchscreen displays you can select this icon to close the menu(s). The close icon is not available on non-touchscreen displays. 4 Scroll bar • Touchscreen — Select the on-screen Back icon to go back to the previous menu. • Non–touchscreen — Use the Back button to go back to the previous menu. 2 • Touchscreen — To scroll through the available menu items, press and hold your finger on the menu to drag it up or down.
Screen item Description 6.17 Editing information in dialogs 1 Status — provides status information for the connected equipment. For example, the Pilot Control dialog displays the locked heading and current navigation mode for a connected autopilot unit. With the dialog displayed: 1. Select the field you want to edit. The on-screen keyboard is displayed: 2 Control icons — provide direct control of the connected equipment.
6.18 Editing numerical settings 6.19 Basic touchscreen operations To edit numerical values in you can either use the Rotary Control, the on-screen numeric adjust control or on-screen numeric keypad to increase or decrease the value. 1 2 3 4 Placing and moving the cursor using touch To place or move the cursor around the screen on a touchscreen multifunction display follow the steps below. 1. Touch the screen at any position on the screen to place the cursor there.
6.20 Databar status symbols Symbol Description AIS unit is connected and switched on, but has active alarms. The status symbols on the databar confirm whether the appropriate connections to your system have been made. The symbols show the status for the following: AIS unit is connected and switched on, but the dangerous and lost alarm is disabled. • Radar scanner. • AIS receiver / transceiver. • Sonar module. • GPS receiver. Sonar status symbols • Autopilot.
Symbol Description Power steering active. 6.21 Initial set up procedures Once your display has been installed and commissioned, Raymarine recommends that you perform an initial set up procedure. Startup wizard Wind Vane mode is active. 1 2 3 4 5 D12568-1 When you power-up the display for the first time or after a system reset a Startup Wizard is displayed. The wizard guides you through the following initial settings: 1. Language selection 2. Vessel type selection 3. Configure units 4.
Adjusting the display brightness — New a Series and New e Series 9. After 2 failed alignment exercises you may be asked to perform a precision alignment exercise. Data master Any system containing more than one networked multifunction display must have a designated data master. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
Note: Any system settings made whilst in Simulator mode are NOT transmitted to other equipment. Enabling and disabling simulator mode You can enable and disable simulator mode by following the steps below. With the homescreen displayed: 1. Select Set-Up . 2. Select System Settings. 3. Select Simulator:. 4. Select On to turn simulator mode on, or 5. Select Off to turn simulator mode off. Note: The Demo movie option is for retail demonstration purposes only.
New a Series / New c Series / New e Series
Chapter 7: Managing display data Chapter contents • 7.1 Memory cards overview on page 88 • 7.2 Inserting a memory card or chart card on page 88 • 7.3 Removing a memory card or chart card on page 89 • 7.4 Saving user data and user settings on page 89 • 7.5 Screenshots on page 92 • 7.
7.1 Memory cards overview You can use memory cards to archive data such as waypoints, routes, and tracks. Memory cards can be used to archive your data when the system capacity is reached. You can then delete old data from your system, creating capacity for new data. The archived data can be retrieved at any time. You can also use memory cards to backup your data. Note: Raymarine recommends that you backup your data to a memory card on a regular basis. 7.
7.3 Removing a memory card or chart card From the homescreen: 1. Select My Data. 2. Select Eject Card. A message is displayed prompting you to select the memory device you want to eject. 3. Select SD1 for a memory card in the top card slot, or SD2 for a memory card in the bottom card slot. 4. Open the chart card door, located on the front right of the display. 5. Push the edge of the card towards the unit, until an audible click is heard.
4. Select SD1 for a memory card in the top card slot, or SD2 for a memory card in the bottom card slot. 5. Select Erase Waypoints from Card, Erase Routes from Card, or Erase Tracks from Card, as appropriate. Application Setting MOB Data type Variation source Erasing waypoints, routes, and tracks from the system Manual variation Language Note: The following procedure permanently erases selected or ALL waypoints, routes, or tracks stored on the display.
Application Setting Data application Data overlay cell 2 on / off Application Setting Data overlay cell 2 content Data Datapages and content Chart object menu Datapage order Chart display Color theme Chart grid Dial color 2D shading Number of engines Community layer Maximum tachometer range Chart text Chart boundaries Spot soundings Fishfinder application Application Setting Fishfinder Configure preset frequencies Safety contour Depth contour Deep water color Weather application App
7.5 Screenshots 7.6 Resetting your system You can take a screenshot of what is currently displayed on the screen. Screenshots are saved to an SD card in .bmp (bitmap) format. The saved image can be viewed form the multifunction display or any device capable of viewing bitmap images. Your system may be reset to its factory default settings if required. Taking a screenshot You can take a screenshot by following the steps below. 1.
Chapter 8: Using the document viewer Chapter contents • 8.
8.1 Document viewer overview • Move your finger up to scroll down the document. Your multifunction display includes a pdf document viewer. • Move your finger down to scroll up the document. The document viewer is available from the homescreen and is used to view and search pdf documents (such as product handbooks). 2 3 4 1 5 When the document width is greater than the width of the application window, move your finger left or right to pan the width of the document.
Searching for text On touchscreen displays you can use the find function to search for text in an open pdf document. With a pdf document open: 1. Select Menu. 2. Select Find. The on-screen keyboard is displayed. 3. Enter the keyword you want to find. 4. Select SAVE. The document viewer will enter find mode and: • You may see a ‘Searching’ icon while all occurrences are found. • The find tool bar is displayed. • The first occurrence of the keyword is highlighted. 5.
New a Series / New c Series / New e Series
Chapter 9: Using autopilot control Chapter contents • 9.1 Autopilot control on page 98 • 9.2 Autopilot status symbols on page 99 • 9.
9.1 Autopilot control You can use your multifunction display to control your autopilot. Note: For information on connecting your multifunction display to a Raymarine autopilot system, refer to the documentation that accompanied your autopilot. With the Autopilot Control function enabled, you can use your multifunction display to: • Engage the autopilot and instruct it to follow a route, or a waypoint. • Disengage the autopilot. • Silence the waypoint arrival alarm.
Engaging the autopilot using the context menu 9.2 Autopilot status symbols From the chart application context menu:: 1. Select any of the following options from the Chart context menu: The autopilot status is indicated in the databar. • Goto Waypoint • Goto Cursor Symbol Description Autopilot is in Standby mode. • Follow Route • Follow from Here Autopilot is in Track mode. • Follow Route in Reverse The pilot control dialog is displayed. 2. Select Yes (Track).
9.3 Autopilot alarms The autopilot function provides alarms to alert you to situations that require action. Your multifunction display shows autopilot alarms, regardless of whether there is active navigation on the system. If autopilot control is enabled, and an alarm is raised by the autopilot, the multifunction display provides an audible alarm sound (providing that the alarm has not already been silenced). The Pilot Control dialog is displayed, indicating a new alarm.
Chapter 10: Using alarms and MOB functions Chapter contents • 10.1 Using Man Overboard (MOB) functions on page 102 • 10.
10.1 Using Man Overboard (MOB) functions Man overboard If you lose a person or object overboard, you can use the Man Overboard (MOB) function to mark the position that the vessel was at when the MOB function was activated. The MOB function is available at all times, regardless of which application is running. MOB can be set to Dead Reckoning or Position mode. Dead Reckoning mode will take into consideration the effects of wind and tides. This usually provides a more accurate course.
10.2 Alarms Alarms alert you to a situation or hazard requiring your attention. You can set up alarms to alert you to certain conditions, such as collision warnings and temperature limits. Alarms are raised by system functions, and also external equipment connected to your multifunction display. When an alarm sounds a message dialog is displayed on your multifunction display and any networked displays. The dialog states the reason for the alarm.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Limit. Shallow Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning alarm on or off and specify the fuel level at which the alarm is triggered.
New a Series / New c Series / New e Series
Chapter 11: Using waypoints, routes and tracks Chapter contents • 11.1 Waypoints on page 108 • 11.2 Routes on page 113 • 11.3 Tracks on page 116 • 11.
11.1 Waypoints Showing and hiding waypoint groups / symbols A waypoint is a position marked on the screen to indicate a site or a place to navigate to. As well as acting as position markers, waypoints are also the building blocks used to create routes. Common waypoint functions are accessed using the waypoints menu. This can be shown at any time by selecting WPT . From the chart or radar application: 1. Select WPT. 2.
• Advance Waypoint 1. Select and hold the required location on screen. The context menu is displayed. 2. Select Place Waypoint. • Measure • Build Route • Acquire Target (only available if Radar overlay is switched on.) • Slew thermal camera (only available when thermal camera is connected and operating.) Accessing the context menu You can access the context menu by following the steps below. 1. New e Series or New c Series: i. Selecting a location, object or target on-screen and pressing the Ok button. 2.
Navigating to a waypoint on the screen Cross Track Error (XTE) Cross Track Error (XTE) is the amount of deviation from your intended route or waypoint, expressed as a distance. XTE D11753-2 From the chart or radar application: 1. Select the waypoint. The waypoint context menu is displayed. 2. Select the Goto Waypoint. Note: With an active waypoint selected you can select Stop Goto option from the waypoint context menu at any time to cancel the action.
Note: You can also access the waypoint list from the homescreen and chart application by going to the My Data menu and selecting Waypoint List. Symbol Type Symbol Type Route start School of fish Seaweed Shark Skull Small fish Sport fisher Square Swimmer Tank Top mark Tower Trawler Tree Triangle Wreck Waypoint editing Editing waypoint details With the Waypoint List displayed: 1. Select the waypoint you want to edit. The waypoint options dialog is displayed. 2. Select Edit Waypoint. 3.
2. Select Erase Waypoint. The erase waypoint pop up message is displayed. 3. Select Yes to confirm, or No to cancel. Note: If you erase a waypoint which is part of a route the erase waypoint in route pop up message is displayed to warn you that the waypoint will be removed from the route. 1. Select the group you want to rename. 2. Select Edit Group Name. The on-screen keyboard is displayed. 3. Using the on-screen keyboard, edit the group name. 4. Select SAVE.
11.2 Routes A route is a series of waypoints typically used to assist with passage planning and navigation. A route is displayed on screen as a series of waypoints linked by a line. D11750-1 Route features There are a range of route features for building, navigating and managing routes. The route features allow you to: • Build and save a route for use when required (stored in the route list). • Navigate (follow) routes. • Manage and edit routes stored on the system. • Build a route from an existing track.
Adjusting chart range while building a route From the Build Route menu: 1. Use the on-screen Range In and Range Out icons to range in and out of the chart. Route context menu Placing the cursor over a route in the chart application displays a context menu showing the leg of the route highlighted by the cursor and menu items. Build a route from a track You can create a route from a recorded track.
You can also follow any route in reverse order. Following a stored route From the chart application: 1. Select Menu. 2. Select Navigate. 3. Select Follow Route. The Route list is displayed. 4. Select the route you want to follow. 5. Select Follow Route. D12295-1 Cancelling navigation of a route You can also reset the XTE from the Navigate Menu: Menu > Navigate > Restart XTE. From the chart application: 1. Select the Route. The route context menu is displayed. 2. Select Stop Follow.
3. Select Yes to confirm or No to cancel the action. 11.3 Tracks Moving a waypoint within a route A track is an on-screen trail that shows the passage you have taken. This trail is made up of a series of track points which are created automatically. You can save the track to create a permanent record of where you have been From the chart application: 1. Position the cursor over the waypoint you want to move. The waypoint context menu is displayed. 2. Select Move Waypoint. 3.
• Auto— The track interval is automatically set (Auto will minimize track points whilst maintaining correlation between the track and the actual path followed). • Erase a track. • Time— The track points are placed at regular intervals of time. • Show or hide a track on the chart (only available from the chart application). • Distance— The track points are placed at regular intervals of distance. • Change the name of a track. 5.
11.4 Waypoints, routes and tracks storage capacity The display can store the following quantities of waypoints, routes and tracks Waypoints • 3000 Waypoints • 100 waypoint groups Routes • 150 routes, each consisting of up to 50 waypoints. Tracks • 15 tracks, each consisting of up to 10000 track points.
Chapter 12: Using the chart Chapter contents • 12.1 Chart application overview on page 120 • 12.2 Chart ranging and panning on page 121 • 12.3 Vessel position and orientation on page 122 • 12.4 Chart views on page 124 • 12.5 Chart context menu on page 125 • 12.6 My Data options on page 126 • 12.7 Navigation options on page 126 • 12.8 Measuring distances and bearings on page 127 • 12.9 Chart vectors on page 127 • 12.10 Current information on page 128 • 12.
12.1 Chart application overview The chart application provides an electronic chart with passage planning and navigation features. It combines 2D and 3D viewpoints and provides a variety of cartographic information regarding your surroundings and charted objects. Typical uses for the chart application include : • Monitor your vessel location and heading. • Interpret your surroundings. It may be possible to use your multifunction display to correlate an NMEA0183 GPS receiver.
Navionics chartplotter sync connection 12.2 Chart ranging and panning You can wirelessly synchronize waypoints and routes between the multifunction display and a tablet or smartphone device. Ranging in and out 1 2 3 The table below shows the Range controls available for each display variant. 4 Rotary Control • New c Series • New e Series Range in and Range out buttons • New c Series Range in and Range out on-screen icons • New a Series D12166-2 1. Multifunction display. 2. Wi-Fi connection.
12.3 Vessel position and orientation Head-Up Vessel position on the chart display Your current position is represented on screen by the vessel symbol. The symbol used for your vessel will vary depending on the vessel type selected during initial set up of your multifunction display. Motor Vessels Sail Vessels D12298-1 Small Vessel Head Up mode displays the chart with your vessel’s current heading upwards. As the heading changes the vessel symbol remains fixed and the chart picture rotates accordingly.
Note: In the 3D chart view, only Relative Motion mode is available. The current motion mode applies to the active instance of the chart application. When you pan the chart the motion mode is no longer active. This is indicated in the status bar by brackets around the motion mode — for example, (Relative Motion). This enables you to view another area of the chart whilst navigating. To reset the motion mode and return your vessel to the screen, select the Find Ship icon or select Find Ship from the menu.
12.4 Chart views 3D chart view The 3D view can display a range of information to help you navigate. Switching between 2D/3D chart view 1 You can switch between 2D and 3D views. From the chart application: 1. Select Menu. 2. Select Presentation . 3. Select Chart View to switch between 2D or 3D. 2 3 4 5 6 7 8 10 9 000°T 11 2D chart view The 2D chart view can display a range of information to help you navigate.
ii. New a series or New e Series — Swipe your finger up or down across the screen to adjust the pitch. D11755-1 4. To adjust the rotation: i. New c Series or New e Series — Move the Joystick Left or Right to adjust the rotation ii. New a Series or New e Series — Swipe your finger left or right across the screen to adjust the rotation. 12.5 Chart context menu Placing the cursor over an area in the chart application displays a context menu showing the cursors positional data and menu items.
12.6 My Data options 12.7 Navigation options The chart provides features to help you manage your data and help plan your navigation to a chosen location. The chart application provides features to help navigate to a chosen location. The options are found in the My Data menu: Menu > My Data. The navigation options are found in the Navigate menu: Menu > Navigate. • Waypoint List — View and edit waypoints stored on the system. • Route List — View and edit routes stored on the system.
12.8 Measuring distances and bearings 12.9 Chart vectors You can use the databar and context menu information you can use the measure function to measure distances in the chart application. Chart vectors display indicators for heading, COG, wind direction and tide direction. You can determine the distance and bearing: A range of vector graphics can be displayed in the chart application when in 2D chart view.
12.10 Current information 7. To set the animation date to 24 hours ahead of the current date select Next Day. Animated current information The electronic charts may allow animation of the current information current stations. Displaying details of currents From the chart application: 1. Select diamond-shaped current icon. The chart context menu is displayed. 2. Select Current Station. The current graph for the selected current station is displayed.
12.11 Tide information Tide graphs Tide graphs provide a graphical view of tidal activity. Animated tide information 1 The electronic charts may allow animation of the tide information tide stations. Animated tide information is available in the chart application wherever a diamond-shaped symbol with a "T" is displayed: This symbol identifies tide stations and the availability of tide information for the location.
12.12 Chart object information You can display additional information on the chart for cartographic objects, ports, and marinas. 5. Select SEARCH. The search results are displayed. 6. Select an entry in the list to display more information. You can also search for the nearest instance of a particular chart object and search for ports by name.
12.13 Chart presentation • Radar — Overlay radar onto the chart (2D view only). The chart has a number of presentation options which affect the level of detail, types of objects and aspects of its operation. The presentation options available are: • NOWRad — Provides the NOWRad weather radar overlay, without the need to open a separate weather application window (2D view only). • Chart detail — Set the level of object detail shown on the chart. • Layers — Set content layers which can be overlaid.
Radar overlay NOWRad weather overlay You can combine the chart with the radar and MARPA functions to provide target tracking or to help you distinguish between fixed objects and other marine traffic. With a suitable weather receiver connected to your multifunction display, you can overlay NOWRad weather information on the chart display.
4. Select Range Rings so that On is highlighted. Selecting range rings will switch range rings between On and Off. Safe Zone Ring The chart application can display and configure a MARPA / AIS safe zone ring. • Course remaining in a straight line. • Current speed maintained. Note: The fuel range ring is an estimated range that can be reached at the current rate of fuel consumption, of the fuel onboard and based on a number of external factors which could either extend or shorten the projected range.
4. Select 3D Display Options. 5. Select Transducer Cone so that On is highlighted. Selecting Transducer cone will switch the function on and off. Enabling depth scale To enable a depth indicator at your vessels location follow the steps below: In 1. 2. 3. 4. 5. 3D view: Select Menu. Select Presentation. Select Layers. Select 3D Display Options. Select Depth Scale so that On is highlighted. Selecting depth scale will switch depth indicator on and off.
12.14 Chart set-up menu options The following table describes the various options in the Chart Set-up Menu for your multifunction display. Menu item Description Options Context Menu (Touchscreen displays only) Determines how the context menu is accessed using touch • Touch — touching a chart object opens the context menu. • Hold — Touch and holding on a chart object opens the context menu. Cartography Provides access to the Cartography menu options.
Cartography set-up menu options The following table describes the various options in the Cartography Set-up Menu for your multifunction display. Menu item Description Options Chart Display Determines the level of detail shown on the chart. • Simple • Detailed (default) • Extra Detailed Chart Grid Determines whether grid lines representing longitude and latitude are displayed on the chart: • Off • On (default) • Off — grid lines are NOT displayed. • On — grid lines are displayed.
Menu item Description Options Nav. Marks Symbols Determines which set of navigation mark symbols is used — International, or US. These symbols correspond to paper charts. • International (default) Determines whether the sector of light cast by a fixed beacon is displayed or not. • Off Light Sectors • US • On (default) • Off — sector of light is NOT displayed. • On — sector of light is displayed. Routing Systems Determines whether routing data is displayed or not.
New a Series / New c Series / New e Series
Chapter 13: Using radar Chapter contents • 13.1 Radar overview on page 140 • 13.2 Radar scan speed on page 141 • 13.3 Radar scanner status symbols on page 141 • 13.4 Radar range and image quality on page 142 • 13.5 Radar display overview on page 144 • 13.6 Dual range radar operation on page 145 • 13.7 Radar mode and orientation on page 146 • 13.8 • 13.9 Radar adjustments: HD and SuperHD scanners on page 149 • 13.10 Radar adjustments: non-HD digital radomes on page 151 • 13.
13.1 Radar overview Radar is used to provide information that can help you to track targets and measure distances and bearings. Radio Detection And Ranging (RADAR) is used at sea to detect the presence of objects (known as ‘targets’) at a distance, and if they are moving, detect their speed. Radar works by transmitting radio pulses, then detecting reflections of these pulses (echoes) from objects in the area and displaying the reflections as targets on your display.
13.2 Radar scan speed 13.3 Radar scanner status symbols SuperHD open array radars with software version 3.23 or above or HD radomes support multiple scan speeds. The radar scanner power mode status is indicated in the databar. Radar scan speed is set up using the Radar Set-up menu.
13.4 Radar range and image quality Maximum radar range The usable range of the radar is limited by factors such as the height of the scanner, and height of the target. Maximum radar range is essentially line-of-sight, so is limited by the height of the scanner and the height of the target as illustrated below: R ma x a1 a2 2 h H 1 3 R ma x = 2.23 ( 2. Select Power up Radar to turn the radar on, or Power down Radar to turn the radar off. 3.
Blind Sectors Obstructions such as funnels and masts near the radar antenna may obstruct the radar beam and cause radar shadows or ‘blind sectors’. If the obstruction is relatively narrow, there will be a reduction of the beam intensity, though not necessarily a complete cut-off. However, for wider obstructions there may be a total loss of signal in the shadow area. There may also be multiple echoes which extend behind the obstruction.
Sea clutter off 13.5 Radar display overview With your radar scanner connected and the radar in transmit mode, the radar picture provides a map-like representation of the area in which the radar is operating. 2 1 3 5 4 6 7 8 9 Sea clutter in auto 10 11 12 13 14 15 D12207-2 Interference When two or more radar-equipped vessels are operating within range of each other mutual radar interference can occur.
that the size of a target on screen is dependent on many factors and may not necessarily be proportional to its physical size. Nearby objects may appear to be the same size as distant larger objects. Note: Colors stated above refer to the default color palette. With experience, the approximate size of different objects can be determined by the relative size and brightness of the echoes.
Scanner Dual Range mode Operating mode 4 Kw SuperHD Open Array Long SuperHD Short HD Long SuperHD Short HD 12 Kw SuperHD Open Array 13.7 Radar mode and orientation Radar orientation modes The radar can operate in a number of orientation modes to suit different types of navigation. The orientation of the radar refers to the relationship between the radar and the direction that you are travelling in.
Course-Up 1 The default motion mode is “Relative”, with zero offset. N N 2 True Motion (TM) When the motion mode is set to True, fixed radar targets maintain a constant position and moving vessels (including your vessel) travel in true perspective to each other and to fixed landmasses on the screen. As the vessel’s position approaches the edge of the screen, the radar picture is automatically reset to reveal the area ahead.
13.8 Radar tuning: On-screen gain controls Touchscreen multifunction displays provide on-screen access to controls for Gain, Rain and Sea clutter. Gain control Rain control Sea control Note: non-touchscreen controls are accessed by the menu options: Menu > Rain and Menu > Adjust Gain. Enabling and disabling on-screen gain controls You can enable and disable the on-screen gain controls by following the steps below. On a touchscreen multifunction display, with the relevant application displayed. 1.
13.9 Radar adjustments: HD and SuperHD scanners You can use the gain presets and other functions to improve the quality of the radar picture. The following settings are available from the Radar menu and apply to HD radomes, HD and SuperHD open array scanners: Menu Item Description Options Auto Gain Mode The radar gain presets enable you to quickly select pre-configured settings to achieve the best picture in different situations.
Adjusting radar anti sea clutter From the radar application, with the required Auto Gain Mode selected: 1. Select Menu. 2. Select Adjust Gain , where shall be the Auto Gain mode already selected. 3. Select Sea: . 4. The Sea clutter slider bar control is displayed. 5. Adjust the Sea clutter slider bar control to the appropriate setting (between 0 and 100%), or 6. Select the Auto box so that a tick is placed in the box for automatic sea clutter control.
13.10 Radar adjustments: non-HD digital radomes You can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-HD digital radomes and are available from the Radar menu: Menu Item Description Options Rain The radar scanner detects echoes from rain or snow. These echoes appear on screen as countless small echoes continuously changing size, intensity and position.
13.11 Radar presentation menu options Function Description Options Dual Range This menu item allows you to turn Dual range mode On and Off. • On • Off Dual Range Channel This menu item allows you to choose long or short channel for dual range.
Function Description Options Data Overlay Set-up This menu item contains a sub-menu which enables you to turn on and select information to display in data cells located on the bottom left of the radar application (Data cells will be displayed in all radar windows).
13.12 Using radar to measure distances, ranges, and bearings When you are using the radar application, you can measure distances, ranges and bearings in a variety of ways.
VRM/EBL context menu The VRM/EBL function includes a context menu which provides positional data and menu items. 1. Position the cursor over the VRM/EBL. 2. Press the Ok button. The radar context menu is displayed. 3. Use the Rotary Control to select Float Center. 4. Press the Ok button. 5. Using the Joystick, move the center position of the circle to the desired position. 6. Press the Ok button to confirm the new position.
13.13 Using radar to track targets and avoid collisions The Guard Zone , VRM/EBL and MARPA functions will help you track targets and avoid collisions. With a radar connected to your multifunction display, you can: • Assess how far away a target is and its bearing (VRM/EBL). • Set an alarm to trigger when a target is within a specified zone (Guard Zone). • Display detailed information on tracked targets (MARPA). • Display the range and bearing of a target.
• The target echo is weak. The target is very close to land, buoys or other large targets. • The target or your own vessel is making rapid manoeuvres. • Choppy sea state conditions exist and the target is buried in excessive sea clutter or in deep swells. • Choppy sea state conditions exist yielding poor stability; own vessel’s heading data is very unstable. • Inadequate heading data.
Vessel vectors (CPA graphics) overview CPA graphics show vectors for your vessel and a selected target. A vector is a line on-screen showing the predicted courses of your vessel and the selected target if you both remain on your present course. These vectors vary in length due to vessel speed and vector length set in the MARPA Set-up menu. 2 1 143°T 28.0kt 0.
13.14 Scanner set-up menu options The Scanner Set-up menu enables you to configure the performance and behavior of your radar scanner.
13.15 Resetting the radar To reset radar settings to defaults follow the steps below: From in the radar application: 1. Select Menu. 2. Select Scanner Set-up. 3. Select Advanced Set-up. 4. Select Reset Advanced. A confirmation pop up message is displayed. 5. Select Yes to confirm reset.
Chapter 14: Using AIS Chapter contents • 14.1 AIS overview on page 162 • 14.2 AIS prerequisites on page 163 • 14.3 AIS context menu on page 163 • 14.4 Enabling AIS on page 164 • 14.5 Displaying AIS vectors on page 164 • 14.6 AIS status symbols on page 165 • 14.7 AIS silent mode on page 165 • 14.8 AIS target symbols on page 166 • 14.9 Displaying detailed AIS target information on page 166 • 14.10 Viewing all AIS targets on page 167 • 14.
14.1 AIS overview AIS Simulator Mode The AIS feature enables you to receive information broadcast by other vessels, and to add these vessels as targets in the chart and radar applications. With an optional AIS unit connected to your system you can: • Display targets for any other AIS-equipped vessels. • Display voyage information being broadcast by these targets, such as their position, course, speed and rate-of-turn.
14.2 AIS prerequisites 14.3 AIS context menu You must have suitable AIS hardware connected to your multifunction display to make use of the AIS functionality. The AIS function includes a context menu which provides AIS target information and menu items. In order to run AIS, you will need: • A receive-only AIS unit or a full AIS transceiver (a unit that sends and receives). • A VHF antenna. • A GPS - to provide position data. • The AIS layer enabled in the chart or radar application, as appropriate.
14.4 Enabling AIS 14.5 Displaying AIS vectors Enabling AIS in the chart application You must have the correct data available before AIS vectors can be displayed. To enable AIS overlay in the chart application the chart view must be set to 2D Menu > Presentation > Chart View. A target is defined as active when it has the following data displayed graphically: From the chart application: 1. Select Menu. 2. Select Presentation. 3. Select Layers. 4. Select AIS: so that On is highlighted.
14.6 AIS status symbols AIS status is indicated by a symbol in the databar. Symbol Description AIS unit is switched on and operating. AIS currently unavailable. AIS unit is switched off, or not connected. AIS unit is in Silent Mode. AIS unit is in Silent Mode, with active alarms. AIS unit is connected and switched on, but has active alarms. AIS unit is connected and switched on, but the dangerous and lost alarm is disabled. Using AIS 14.
14.8 AIS target symbols Your multifunction display shows a range of symbols to represent the different types of AIS target. Target type Description Transmitting target Target is moving or at anchor (Target is not activated, dangerous or lost). Activated target Target activated — that is, AIS vector displayed. Vector line (optional) shows predicted distance travelled within a given time. Selected target Target selected with cursor. Can view detailed data. Symbol 14.
14.10 Viewing all AIS targets 14.11 Using AIS to avoid collisions From the chart application go to Menu > AIS Options You can use the AIS safe zone and safety message functions to help you avoid collisions with other vessels and objects. From the radar application go to Menu > Track Targets > View AIS Lists 1. Select AIS List. A list of all available AIS targets is displayed.
2. Select Track Targets. 3. Select AIS Unit Set-up. 4. Select AIS Safety Messages. Selecting AIS Safety Messages will switch between safety messages On and Off. Displaying safety-critical AIS information From the chart or radar application: 1. Select the AIS target. The AIS target context menu is displayed. 2. Select AIS Data so that On is highlighted. Selecting AIS Data will switch between AIS data On and Off. 14.
14.13 AIS alarms 14.14 Buddy tracking The AIS functions generate a number of alarms to alert you to dangerous or lost targets. The Buddy Tracking feature enables you to add AIS-equipped friends and regular contacts to a “Buddy List” on your multifunction display. As soon as a vessel on your Buddy List sails into the range of your AIS unit, the vessel icon changes to indicate this. In addition to the dangerous target alarm, the system generates an alarm when a dangerous target becomes a lost target i.e.
ii. Select No to save the vessel to your buddy list without entering a name for the buddy vessel. The vessel will now be added to your buddy directory. Adding a vessel to your buddy list from AIS target list 1. If you are in the chart application, goto Menu > AIS Options. 2. If you are in the radar application, goto Menu > Track Targets > View MARPA & AIS Lists. 3. Select View AIS List. The AIS Target List is displayed. 4. Select an AIS target. 5. Select Add Buddy. i.
Chapter 15: Using the fishfinder Chapter contents • 15.1 How the fishfinder works on page 172 • 15.2 Raymarine sonar modules on page 172 • 15.3 Traditional sonar technology on page 173 • 15.4 Broadband CHIRP sonar technology on page 173 • 15.5 Fishfinder introduction on page 174 • 15.6 Transducer bandwidth on page 175 • 15.7 The sonar image on page 175 • 15.8 Fishfinder presets on page 176 • 15.9 Dual / Single frequency fishfinder on page 177 • 15.
15.1 How the fishfinder works 15.2 Raymarine sonar modules The fishfinder application uses a sonar module and a suitable sonar transducer. The sonar module interprets signals from the transducer and builds up a detailed underwater view. The table below lists Raymarine’s sonar modules and whether CHIRP technology is used. The transducer is located on the bottom of the boat, it sends pulses of sound waves into the water and measures the time it takes for the sound wave to travel to the bottom and back.
15.3 Traditional sonar technology 15.4 Broadband CHIRP sonar technology Traditional sounders use a single carrier frequency or carrier wave for the sonar ping. These sounders work by measuring the time it takes the ping echo to return to the transducer to determine target depth.
15.5 Fishfinder introduction Warning: Sonar operation Fishfinder context menu The fishfinder application includes a context menu which provides fishfinder information and shortcuts to menu items. • NEVER operate the sonar with the vessel out of the water. • NEVER touch the transducer face when the sonar is powered on. • SWITCH OFF the sonar if divers are likely to be within 7.6 m (25 ft) of the transducer.
15.6 Transducer bandwidth 15.7 The sonar image The fishfinder application displays the fishfinder frequency, center frequency or CHIRP mode depending on the connected sonar module and transducer. Interpreting the seabed using sonar Example of CHIRP sonar module in CHIRP mode. It is important to understand how to correctly interpret the seabed structure represented in the fishfinder display. The seabed usually produces a strong echo.
15.8 Fishfinder presets The fishfinder provides you with four preset configurations available from the fishfinder menu. These enable you to quickly select appropriate settings tailored for various situations. Each preset has been configured to provide the best operating parameters for the fishfinder. However, it is possible to manually adjust the presets if necessary.
15.9 Dual / Single frequency fishfinder Dual frequency operation allows the sonar to operate and display 2 frequencies simultaneously. If the preset mode that you are using has two frequencies configured, you can view either one or both of those frequencies in separate windows. Selecting dual frequency view From the fishfinder application: 1. Select Menu. 2. Select Presets. 3. Select Dual. The main fishfinder menu is displayed. 4. Select View Freq. 5.
The graph above depicts an example of the fine tuning (from —50% to +50%) available when the frequency is set to 200 kHz. Tuning the fishfinder frequency (non-CHIRP sonar module) When connected to a non-CHIRP sonar module you can manually tune the fishfinder frequency. From the fishfinder application: 1. select Menu. 2. Select Frequency settings. 3. Select either Tune Freq 1 or Tune Freq 2 as required. The Tune Frequency slider bar is displayed: 15.
Frequency adjustment (CHIRP sonar module in non-CHIRP mode) When using a CHIRP sonar module in CHIRP mode (Low Chirp, Med Chirp or High Chirp) the frequency cannot be adjusted. When using a CHIRP sonar module in a non-Chirp mode (e.g. 50 kHz or 160 kHz) the frequency at which the transducer is transmitting can be adjusted. With the CHIRP sonar module set to a CHIRP mode (e.g. Low Chirp or High Chirp) the CHIRP sonar module will sweep the transducer’s available frequency range in each ping.
15.12 Fishfinder display modes Selecting a fishfinder display mode From the fishfinder application: 1. Select Menu. 2. Select Display Mode. 3. With dual frequency preset set, select Adjust to select which frequency display you wish to change. Selecting Adjust in Dual frequency preset will switch between Frequency 1 and Frequency 2. 4. Select the Select Mode menu item. 5.
Bottom Lock 15.13 Fishfinder range The Bottom Lock function applies a filter to flatten the image of the seabed and make any objects on or just above it easier to discern. This feature is particularly useful for finding fish that feed close to the bottom. The Range and Range Shift functions enable you to change the range of depth displayed by the fishfinder. Bottom Lock is selected for individual fishfinder windows and can replace or appear alongside the standard fishfinder image.
Rotary Control • New c Series • New e Series 15.14 Fishfinder sensitivity settings The Sensitivity settings menu provides access to features and functions which enhance what is displayed on screen. Sensitivity options include: • Gain Range in and Range out buttons Slide the screen Up or Down • New c Series • New e Series (excluding e7 and e7D • New e Series • Gain Mode — Only available when connected to a non-CHIRP sonar module including the internal sonar module.
5. Select Auto. A tick is displayed in the Auto box to signify automatic gain is enabled. Setting the auto gain mode for non-CHIRP sonar modules When using a non-CHIRP sonar module, from the fishfinder application: 1. Select Menu. 2. Select Sensitivity Settings. 3. Select Gain Mode. A list of available auto gain modes is displayed: • Cruising (Low) Setting auto gain using the on-screen controls Touchscreen multifunction displays provide on-screen access to the gain controls. 1.
• Medium • High When connected to a Raymarine sonar module without CHIRP capabilities an automatic setting is available: • Auto Selecting the frequency for TVG adjustments When connected to a Raymarine CHIRP sonar module, the TVG for frequency 1 and frequency 2 can be changed independently or both at the same time. If connected to a non-CHIRP sonar module adjustments will be made to both frequencies simultaneously. From the fishfinder application: 1. Select Menu. 2. Select Sensitivity Settings. 3.
2. Select Sensitivity Settings. 3. Select Color Threshold. Selecting color threshold displays the numeric adjust control. 4. Adjust the color threshold to the required setting. 5. Select Ok to confirm setting and close the numeric adjust control. Fishfinder power 15.15 Fishfinder presentation options The Presentation menu gives you access to features and functions which provide additional on-screen functionality.
Menu Item Description • Data Cell 2 Options Allows selection of a data type by category. Data Cell 2 • Select Data Category • On • Select Data Category 15.16 Depth and distance with the fishfinder The fishfinder display provides a number of features to help you determine depths and distances. These features are illustrated and described in more detail below: • Off 1 Select Data Category Allows selection of a data type by category.
15.17 Fishfinder scrolling The fishfinder image scrolls from right to left. You can pause the scrolling or adjust the scroll speed, to ease placing of waypoints or VRMs on-screen. Scroll speed You can adjust the speed at which the fishfinder image scrolls. A faster speed provides more detail which may be useful when you are looking for fish. If you select a slower speed the information remains on the display for longer.
15.18 Fishfinder waypoints 15.19 Fishfinder alarms Placing a waypoint on the fishfinder display enables you to mark a position so that you can return to it later. The display can be configured to provide a number of fishfinder alarms. When a waypoint is placed, its details are added to the waypoint list and a vertical line labelled WPT is displayed on-screen. The waypoints can then be navigated to using the chart application.
15.20 Sounder set–up menu options This section describes the settings you can change using the sounder set up menu: (Menu > Set-up > Sounder Set-up). The set up menu contains settings that are likely to be changed infrequently. Menu Item Description Options Internal Sounder Switch the built in sonar on and off, for use when you have more than one multifunction display with internal sonar. • On • Off Note: Disabled on non-sonar variants. Note: Must be set to Off if an external sonar is connected.
15.21 Transducer set-up menu options The Transducer Set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu Item Description Options Transducer Select the appropriate transducer type from those displayed. Some transducer may be detected by the system automatically. Options available are dependant on the sonar module connected. Speed Transducer Select the appropriate speed transducer from those available.
15.22 Resetting the sonar The reset function restores the unit to its factory default values. Note: Performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible Raymarine multifunction display go to the Fishfinder application page. 2. Select Menu from the side menu. 3. Select Set-up. 4. Select Sounder Set-up. 5. Select Sonar reset. 6. Select Yes to confirm. The unit will now be reset to factory default settings.
New a Series / New c Series / New e Series
Chapter 16: Using the data application Chapter contents • 16.1 Data application overview on page 194 • 16.2 Pre-configured datapages on page 194 • 16.
16.1 Data application overview 16.2 Pre-configured datapages The data application displays system and instrument data on your multifunction display. By default, a pre-configured range of data is displayed in a number of datapages. Each datapage consists of a number of 'cells', each containing a different item of data. The data application enables you to view numeric data generated by the system.
Datapage a65 / a67 / e7 / e7D Engine (Number of engines = 2) • Port Oil Pressure Engine (Number of engines = 3) e95 / e97 / c95 / c97 / e125 / e127 / c125 / c127 / e165 Datapage a65 / a67 / e7 / e7D Fuel • Port Coolant temperature e95 / e97 / c95 / c97 / e125 / e127 / c125 / c127 / e165 • Port Coolant temperature • Port Oil Pressure • Port RPM • Port Fuel remaining • Trim tabs • Starboard Coolant temperature • Starboard Oil Pressure • Starboard Oil Pressure • Starboard Coolant temperature
16.3 Customizing the data application You can customize the data application to show the system and instrument data that you require. In addition to displaying the default, pre-configured datapages in the data application, you can also: • Change the order datapages appear. • Customize datapages content to your specific requirements. • Rename the datapages. • Add new custom datapages. • Delete existing datapages. • Set the number of engines your vessel has (1 to 5). • Set the maximum engine RPM range.
Customizing datapage content From the data application: 1. Select Menu. 2. Select Edit Page. 3. Select the cell you want to change. 4. Select Select Data Category. 5. Select a data category. Selecting a data category will display a list of data items for that category. 6. Select the data item you want to display. Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the new data item 7. Repeat steps 3 to 6 for all the data items you want to change.
Data Category Description Data Item Fuel Types of data related to the fuel system. For example, fuel levels. Fuel Level 1 (vol) Note: The options displayed are dependant on the number of engines set in the data application.
Data Category Description Data Item Navigation Types of data related to navigation. For example, bearing to waypoint. Cursor Position (Only available in the Databar and data overlay.) Digital Dial Graphical Cursor info Cross Track Error Rolling Road (Only available in the Data application.) Compass Target Position Bearing to Waypoint Distance to Waypoint WPT TTG Waypoint Info Pilot Pilot-related data. For example, rudder. Rudder Speed Speed-related data.
7. Select the data item you want to display. Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the selected data item. 8. Repeat steps 3 to 6 for all the data items you want to change. 9. Select Rename Page. The on screen keyboard is displayed. 10. Enter the new name for the datapage. 11. Select SAVE. 4 Engines Deleting a datapage You can delete custom or pre-configured datapages from the data application.
Datapage and dial colors Datapage color theme and dial colors can be switched between light and dark. Color Theme Dial Color Light Light Light Dark Dark Dark Dark Light Example Resetting all datapages You can reset the datapages in the data application to the factory defaults. 1. Select Menu. 2. Select Reset All Pages. The confirm reset pop up message is displayed. 3. Select Yes to reset or No to cancel the action.
New a Series / New c Series / New e Series
Chapter 17: Using the fuel manager Chapter contents • 17.
17.1 Fuel manager overview Note: The fuel manager provides an estimate of fuel remaining, and the distance and time which can be travelled before the tanks are empty. In order to calculate these values, you must configure the total capacity of fuel available to the engines and log each time you add fuel. The fuel manager also allows you to set a low fuel warning alarm which is sounded when the vessel's estimated fuel falls below a specified value.
5. Select Fuel Level. The fuel level numeric adjust control is displayed. 6. Adjust the fuel level to the required value. The low fuel alarm will now be sounded when the fuel remaining in the tank falls to the value specified. 1. 2. 3. 4. Select Menu. Select Presentation. Select Layers. Select Fuel Range Ring. Selecting Fuel Range Ring will switch the function On and Off. Note: By default the low fuel alarm is switched off.
New a Series / New c Series / New e Series
Chapter 18: Using the weather application (North America only) Chapter contents • 18.1 Weather application overview on page 208 • 18.2 Weather application set up on page 208 • 18.3 Weather application display overview on page 209 • 18.4 Weather map navigation on page 212 • 18.5 Weather context menu on page 212 • 18.6 Weather information on page 213 • 18.7 Weather reports on page 213 • 18.8 Animated weather graphics on page 214 • 18.9 Weather application menu options on page 215 • 18.
18.1 Weather application overview 18.2 Weather application set up The weather application overlays historical, live, and forecasted weather graphics on a world map. A number of steps must be completed before you can use the weather application for the first time. The weather application can only be used in North America and its coastal waters. • Your multifunction display must be connected to a Raymarine Sirius weather receiver.
18.3 Weather application display overview Symbol Lightning — a lightning symbol is shown at each cloud-to-ground strike: The weather application displays a range of graphics to indicate weather conditions and forecast information. • Light (recorded in last 10–15 minutes.) The following diagram illustrates the main features of the weather application display: 1 2 3 Description • Medium (recorded in last 5–10 minutes.) 4 • Dark (recorded in last 0–5 minutes.
Historical (grey) Current (red) Forecast (orange) Wind speed symbols Description Hurricane (Category 1–5) The weather application uses a range of symbols to represent different wind speeds.
NOWRad precipitation color codes Reflectivity Intensity Rainfall (mm/hr) Rainfall (in/hr) NOWRad displays the type and level of precipitation: 90 15376.51 599.69 95 31575.91 1231.46 100 64841.98 2528.84 105 133154.6 5193.03 110 273436.4 10664.
18.4 Weather map navigation 18.5 Weather context menu You can move around the weather map and place waypoints. The weather application includes a context menu which provides positional data and the option to view weather reports from the cursor location. When you open the weather application, a world map is displayed. If the system has a position fix for your vessel, the map will be centred on your location.
18.6 Weather information 18.7 Weather reports You can view weather information for: You can view a number of different weather reports to give you a comprehensive view of the weather. • a specific location • a surface observation station (when displayed) • Cities (when displayed) Your multifunction display shows weather reports for: • Tropical statements. • Marine warnings. Viewing weather data at a specific location • Marine zone forecasts.
18.8 Animated weather graphics You can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • NOWRad — weather radar 1 • Wind • Waves • Pressure — surface pressure D12297-1 Item Description 1 Watchbox alert box Viewing watchbox alerts You can view a watchbox alert at any time by following the steps below: From the weather application with a watchbox alert box displayed. 1.
18.9 Weather application menu options The following options are available from the weather application menu: Menu item Description Find Ship Selecting Find Ship will reset the display to show your vessel in the center of the screen. Display Graphics The Display Graphics menu allows to choose what graphics to Show or Hide in the weather application. Menu item Description Options Watchbox Alert The Watchbox Alerts menu allows you to turn alerts Off, or select a range.
18.10 Glossary of weather terms Term Definition Cold front The boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone A large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depression”. Also the name used for a hurricane in the Indian Ocean and Western Pacific. Depression An area of low pressure. Also called a cyclone.
Term Definition Wave cyclone A storm or low pressure centre that moves along a front. Wave period The period is the time gap between successive waves and the longer the period the faster the waves travel.
New a Series / New c Series / New e Series
Chapter 19: Using the thermal camera application Chapter contents • 19.1 Thermal camera application overview on page 220 • 19.2 Thermal camera image on page 220 • 19.3 Controls overview on page 221 • 19.4 Camera control on page 222 • 19.5 Image adjustments on page 224 • 19.
19.1 Thermal camera application overview The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. 19.2 Thermal camera image The thermal camera provides a video image which is shown on your display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Icon Description 19.3 Controls overview Rear-view mode — image is flipped horizontally. The thermal camera application is available on compatible Raymarine multifunction displays and systems. It includes controls for the thermal camera. Zoom setting: 2x zoom. Thermal camera application – hardkey controls Rotary control Zoom image in / out. Joystick / trackpad • Pan and tilt camera Zoom setting: 4x zoom. Note: On touchscreen displays you can also use the touchscreen to pan and tilt the camera.
• JCU Icon 19.4 Camera control • PC Icon Power up and standby • Restore Factory Defaults When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in Standby mode. • Calibrate Platform Note: The thermal camera menu options available are dependant on the software version of your multifunction display and thermal camera.
Panning and tilting, and the thermal image On a New e Series multifunction display you can pan and tilt the thermal camera image using the touchscreen. Move your finger up and down the screen to tilt the camera up or down. The scan width determines the distance that the camera pans left and right when in surveillance mode. Scan Speed The scan speed determines the speed at which the camera pans left and right when in surveillance mode.
Thermal camera point mode 19.5 Image adjustments Point mode is only applicable to thermal cameras which have mechanical stabilization. Adjusting the thermal camera image Enabling point mode only has significance when stabilization is enabled. Enabling point mode turns off the horizontal (pan) stabilization while retaining the vertical (tilt) stabilization.
Thermal camera reverse video Thermal camera rear view mode You can reverse the polarity of the video image to change the appearance of objects on-screen. The reverse video option (video polarity) switches the thermal image from white-hot (or red-hot if the color mode setting is active) to black-hot. The difference between white-hot and black-hot is shown below: The rear view mode flips the video image horizontally, providing a “mirror image”.
2. Select Camera Set-up. 3. Select Slew Settings. The Slew settings page is displayed which includes the following auto slew options: • Auto Slew to MOB • Auto Slew to Dangerous AIS target 19.6 Camera set-up menu Set Home Position Sets the camera’s current position as the Camera Home position. Slew Settings Provides automatic slew options and camera alignment settings. • Auto Slew to Dangerous MARPA target 4. Select the relevant option.
High Power Torque JCU Icon PC Icon This option controls the amount of power used to hold the camera steady when in use. With the setting enabled the camera will consume more power, but will help ensure that the camera is held in place in rough seas. The High Power Torque mode may be useful for power boats that operate at higher speeds and experience high impact environments, and can accept higher power consumption. • On (default) Shows or hides the on-screen JCU connected icon.
New a Series / New c Series / New e Series
Chapter 20: Using the camera application Chapter contents • 20.
20.1 Camera application overview 2. Move the Joystick Up to display the previous video feed. You can view a camera or a video feed which is connected directly to your multifunction display using the video input(s) or IP camera feeds which are available on your network. The camera application can be set to cycle through all available feeds. If supported by your camera, you can adjust the brightness, contrast, color and aspect ratio of the video image. PAL / NTSC is selected automatically.
1. Select Menu > Camera Cycling > Camera Cycling so that Off is highlighted, or 2. Change the camera / video feed manually as described earlier in this section, or 3. Press the Back button (applicable to New c Series and New e Series only). Naming camera / video feeds To aid selection of feeds you can name each feed. From the Camera application: 1. Select the feed you want to name so that it is displayed on the screen. 2. Select Menu. 3. Select Edit Name. The on-screen keyboard is displayed. 4.
New a Series / New c Series / New e Series
Chapter 21: Using mobile applications Chapter contents • 21.1 Raymarine mobile apps on page 234 • 21.2 Enabling Wi-Fi on page 235 • 21.3 Enabling mobile apps on page 235 • 21.4 Setting up Wi-Fi security on page 236 • 21.
21.1 Raymarine mobile apps 1 2 3 4 Raymarine mobile apps enable viewing and control of your multifunction display via a compatible mobile device, using a Wi-Fi connection. Raymarine currently offers the following mobile apps: • RayView D12599-1 • RayRemote 1. Multifunction display. • RayControl 2. Wi-Fi connection (2 way – streaming or remote control). Note: Your multifunction display must have software version V3.15 or later in order to use mobile apps. 3. Compatible smartphone. 4.
21.2 Enabling Wi-Fi 21.3 Enabling mobile apps With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Wi-Fi > ON. Raymarine mobile apps must be enabled on your multifunction display before you can stream video or remote control your multifunction display via a tablet or smartphone device. Using mobile applications With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4.
21.4 Setting up Wi-Fi security 21.5 Selecting a Wi-Fi channel You can encrypt the Wi-Fi connection on the multifunction display to prevent unauthorized devices from accessing the connection. The default encryption is WPA2. By default the multifunction display automatically selects an available Wi-Fi channel.
Chapter 22: Media player application Chapter contents • 22.1 Media player connection on page 238 • 22.2 Enabling Bluetooth on page 238 • 22.3 Pairing a Bluetooth media player on page 239 • 22.4 Enabling audio control on page 239 • 22.5 Media player controls on page 240 • 22.6 Media player controls using a remote control on page 240 • 22.
22.1 Media player connection 22.2 Enabling Bluetooth You can use your multifunction display to wirelessly control a Bluetooth-compatible media player (such as a smartphone). With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Bluetooth > On. The media player must be compatible with the Bluetooth AVRCP protocol (version 2.1 or higher). 1 2 3 D12164-2 1. Multifunction display. 2. Bluetooth connection. 3.
22.3 Pairing a Bluetooth media player 22.4 Enabling audio control With the homescreen displayed and Bluetooth turned on: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select New Bluetooth Connection. A message is displayed prompting you to put your media player device into discovery mode. 5. Ensure Bluetooth is enabled on your external media player device and ensure it is ready to be paired. For more information, consult the instructions that accompany the device. 6.
22.5 Media player controls Touchscreen multifunction displays enable you to use the on-screen media player controls to control the audio playing on your external media player. 22.6 Media player controls using a remote control You can control audio wirelessly using a Raymarine RCU-3 remote control unit. The Shortcut key on the RCU-3 must be set to Start/Stop audio playback, refer to the Using a Remote control section for further details. 1 1. Press UP arrow for next track. 2.
22.7 Unpairing a Bluetooth device If you are experiencing problems when attempting to use a Bluetooth device with the multifunction display it may be necessary to unpair the device (and any other paired Bluetooth devices) and then retry the pairing procedure. With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Connection Manager. 5. Select the media player device in the list. 6. Select Unpair / Forget this device.
New a Series / New c Series / New e Series
Chapter 23: Using a remote control Chapter contents • 23.1 Remote control connection on page 244 • 23.2 Pairing the remote and configuring the UP and DOWN buttons on page 244 • 23.3 Operating principles on page 245 • 23.4 Customizing the SHORTCUT button on page 245 • 23.5 Remote control functions on page 246 • 23.
23.1 Remote control connection 23.2 Pairing the remote and configuring the UP and DOWN buttons You can control the multifunction display wirelessly using a Raymarine remote control unit. The remote control uses a Bluetooth wireless connection. 1 2 3 D12163-2 1. Multifunction display. 2. Bluetooth connection. 3. Raymarine Bluetooth remote control (for example, RCU-3). To use the remote control you must first: • Enable Bluetooth in the System Settings on the multifunction display.
23.3 Operating principles 23.4 Customizing the SHORTCUT button Remote control operating principles. On your multifunction display, with the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select External Devices. 4. Select Remote Control. 5. Select Customize shortcut key. 6. Select the function that you want to assign to the SHORTCUT key. • Only 1 multifunction display may be operated by a remote control unit at any one time.
23.5 Remote control functions Bu tto n s Arrow buttons Shortcut button Ra n g e or P a ir S e le c t D12051-2 Button Default functions: Range / zoom. Application where function available: Chart Radar Fishfinder Weather Homescreen • Press UP or DOWN arrow for momentary response. • Hold UP or DOWN arrow for continuous response. Open homescreen. Shortcut: Hold Select application in homescreen (in left-to-right, top-to-bottom order). • Press UP or DOWN arrow for momentary response.
23.6 Reconnecting the RCU 1. When you pair the RCU-3 with a multifunction display a wireless connection is established. 2. When you power off the multifunction display it loses its connection with the RCU-3 after 10 minutes. 60 5 55 10 50 15 45 40 Minutes 20 35 30 25 = > 10 Minutes 3. To restore the connection between the 2 units, press and hold any button on the RCU-3 for at least 3 seconds.
New a Series / New c Series / New e Series
Chapter 24: DSC VHF radio integration Chapter contents • 24.1 Using a DSC VHF radio with your display on page 250 • 24.
24.1 Using a DSC VHF radio with your display You can connect your DSC VHF radio to your multifunction display and show distress message information and GPS position data for other vessels.
Chapter 25: Customizing your display Chapter contents • 25.1 Language selection on page 252 • 25.2 Boat details on page 253 • 25.3 Units set-up on page 254 • 25.4 Time and Date set-up on page 255 • 25.5 Display preferences on page 256 • 25.6 Data cell and databar customization on page 258 • 25.
25.1 Language selection The system can operate in the following languages: English (US) English (UK) Arabic Chinese Croatian Danish Dutch Finnish French German Greek Italian Japanese Korean Norwegian Polish Portuguese (Brazilian) Russian Spanish Swedish Turkish With the homescreen displayed: 1. Select Customize. 2. Select Language. 3. Select from the languages available.
25.2 Boat details You can customize various aspects of the display's functions to make them specific to your vessel. Menu item Description Options Boat Type You can change the appearance of the vessel in the chart application. Select the option that most closely resembles the type and size of your vessel. • Power Cruiser 1 (default) Note: When boat type is selected during the initial set up of the multifunction display the boat type shall determine the datapage configuration in the data application.
25.3 Units set-up You can specify your preference for the units of measurement that will be used in all applications. Menu item Description Options Distance Units The units of measure that will be used in all applications for the display of all values related to distance. • Nautical Miles • Statute Miles • Kilometers Speed Units The units of measure that will be used in all applications for the display of all values related to speed.
25.4 Time and Date set-up You can specify your preference for the way that time and date will appear in all applications. Menu item Description Options Date Format Allows you to specify the preferred format for the display of date information in all applications. • MM:DD:YY (Month, Day, Year) Allows you to specify the preferred format for the display of time information in all applications.
25.5 Display preferences You can specify your preference for general display behavior. Menu item Description Options Key Beep An audible sound can be made each time a button is pressed or the touchscreen is used. • ON (default) If set to On, the cursor will be automatically hidden after a period of no movement. If set to Off, the cursor will persist on the screen until moved.
Multiple brightness groups can be configured. This can reflect the physical location of the units on your vessel if required. For example, the units at your helm can be set to one group, and the units on the flybridge can be set to a different group. In this example, any brightness adjustments made to a unit at the helm would be automatically reflected in the other units at the helm but not on the flybridge.
25.6 Data cell and databar customization You can customize the data displayed in on-screen cells with a wide range of data. Customizable data is displayed in the databar, extended databar (HybridTouch displays only) or data cells areas of the screen. The databar, extended databar and data cells are available in all applications.
List of data items Depending on connected devices the categories of data available to display in the data application, data overlay, databar, and expanded databar are shown below. The following table shows the data items available by category. Data Category Description Data Item Boat Types of data generated by your vessel. For example, tank levels. Fresh Water Digital Dial Graphical Grey Water Black Water Live Well Trim Tabs (Only available in the Data application.) Depth Depth data.
Data Category Description Data Item Fuel Types of data related to the fuel system. For example, fuel levels. Fuel Level 1 (vol) Note: The options displayed are dependant on the number of engines set in the data application.
Data Category Description Data Item Navigation Types of data related to navigation. For example, bearing to waypoint. Cursor Position (Only available in the Databar and data overlay.) Digital Dial Graphical Cursor info Cross Track Error Rolling Road (Only available in the Data application.) Compass Target Position Bearing to Waypoint Distance to Waypoint WPT TTG Waypoint Info Pilot Pilot-related data. For example, rudder. Rudder Speed Speed-related data.
25.7 System set-up menus The system set-up menus enable you to configure your display and connected external devices. The following menus are available: Menu item Description Alarms Enables you to configure all the different types of alarms produced by the display and connected equipment. Pilot Controls Displays the Pilot Control dialog. Fuel Manager Displays the Fuel manager page Audio Controls Displays the audio controls pop-up.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Limit. Shallow Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning alarm on or off and specify the fuel level at which the alarm is triggered.
Ground trip resets menu This menu enables you to resets the chosen ground trip distance counter to zero. Menu item Description Ground Trip 1 Reset Resets the ground trip 1 distance counter to zero. Ground Trip 2 Reset Resets the ground trip 2 distance counter to zero. Ground Trip 3 Reset Resets the ground trip 3 distance counter to zero. Ground Trip 4 Reset Resets the ground trip 4 distance counter to zero. System settings menu • Status. Menu item Description Options • Azimuth angle.
Multiple data sources (MDS) overview Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. • Speed. • Wind. Typically this exercise is completed as part of the initial installation, or when new equipment is added.
Connections menu This menu enables you to connect wireless Bluetooth and Wi-Fi devices to the display. Menu item Description Options Bluetooth Enable or disable Bluetooth on the display. • On • Off (default) Wi-Fi Enable or disable Wi-Fi on the display. • On • Off (default) Connection Manager Provides a list of Bluetooth devices in range. When you highlight a connection in the list and press OK, the following options are available: • Unpair / Forget this device • Audio control On / Off.
Menu item Description should set this option to OFF to ensure that all NMEA-connected units receive heading data from the external heading sensor. Options NMEA Output Settings Allows you to enable or disable the individual NMEA “sentences” that are sent by the multifunction display to any devices connected the NMEA output port.
Menu item Description Options • If you have a Raymarine GPS receiver using SeaTalk or SeaTalkng, it will automatically correlate each time you change the datum on the multifunction display. • If you have a Raymarine GPS receiver using NMEA 0183, or a third-party GPS receiver, you must correlate it separately. It may be possible to use your multifunction display to correlate an NMEA 0183 GPS receiver. From the homescreen go to Set-up > System settings > GPS Set-up > View Satellite Status.
Maintenance menu This menu provides access to systems settings reset and diagnostics. Menu item Description Options Touchscreen Alignment If the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object with your touch. For best results, perform this exercise when your vessel is anchored or moored. Note: The Touchscreen alignment option is not required on New c Series displays.
Chapter 26: Maintaining your display Chapter contents • 26.1 Service and maintenance on page 272 • 26.
26.1 Service and maintenance 26.2 Cleaning This product contains no user serviceable components. Please refer all maintenance and repair to authorized Raymarine dealers. Unauthorized repair may affect your warranty. Best cleaning practices. Routine equipment checks Raymarine strongly recommends that you complete a number of routine checks to ensure the correct and reliable operation of your equipment.
Chapter 27: Troubleshooting Chapter contents • 27.1 Troubleshooting on page 274 • 27.2 Power up troubleshooting on page 275 • 27.3 Radar troubleshooting on page 276 • 27.4 GPS troubleshooting on page 277 • 27.5 Sonar troubleshooting on page 278 • 27.6 Thermal camera troubleshooting on page 279 • 27.7 System data troubleshooting on page 280 • 27.8 Video troubleshooting on page 281 • 27.9 Wi-Fi troubleshooting on page 282 • 27.10 Bluetooth troubleshooting on page 283 • 27.
27.1 Troubleshooting The troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your product this section will help you to diagnose and correct problems in order to restore normal operation.
27.2 Power up troubleshooting Problems at power up and their possible causes and solutions are described here. Problem Possible causes Possible solutions The system (or part of it) does not start up. Power supply problem. Check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. Check that the power source is of the correct voltage and sufficient current.
27.3 Radar troubleshooting Problems with the radar and their possible causes and solutions are described here. Problem Possible causes Possible solutions No Data or No scanner message Radar scanner power supply Check that the scanner power supply cable is sound and that all connections are tight and free from corrosion. Check relevant fuses and breakers. Check power source is of the correct voltage and sufficient current (using voltage booster if appropriate).
27.4 GPS troubleshooting Problems with the GPS and their possible causes and solutions are described here. Problem Possible causes Possible solutions “No Fix” GPS status icon is displayed. Geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another geographic location. GPS connection fault. Ensure that external GPS connections and cabling are correct and fault free. External GPS antenna in poor position.
27.5 Sonar troubleshooting Problems with the sonar and their possible causes and solutions are described here. Problem Possible causes Possible solutions Sonar data not available on multifunction display. Unit power supply fault. Check the unit power supply and cables. Other unit fault. Refer to the instructions supplied with the unit. SeaTalkhs / RayNet network problem. Check that the unit is correctly connected to a Raymarine network SeaTalkhs switch or crossover coupler (as applicable).
27.6 Thermal camera troubleshooting Problems with the thermal camera and their possible causes and solutions are described here. Problem Possible causes Possible solutions Video not displayed. Camera is in Standby mode. The camera will not display video if it is in Standby mode. Use the camera controls (either the thermal camera application or JCU) to “wake” the camera from standby. Problem with the thermal camera video connections.
27.7 System data troubleshooting Aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions Instrument, engine or other system data is unavailable at all displays. Data is not being received at the display. Check the data bus (e.g. SeaTalkng) wiring and connections. Check the overall integrity of the data bus (e.g. SeaTalkng) wiring.
27.8 Video troubleshooting Problems with the video inputs and their possible causes and solutions are described here. Problem Possible causes Possible solutions No signal message on screen (video image not displayed) Cable or connection fault Check that the connections are sound and free from corrosion.
27.9 Wi-Fi troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. Tablet / smartphone does not have a wireless connection established with the multifunction display. Ensure that Wi-Fi is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Wireless Connections > Wi-Fi > On).
27.10 Bluetooth troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. iPhone does not have a Bluetooth connection established with the multifunction display. Ensure that Bluetooth is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Connections > Bluetooth > On).
27.11 Touchscreen troubleshooting Problems with the touchscreen and their possible causes and solutions are described here. Problem Possible causes Possible solutions Touchscreen does not operate as expected Touch lock is enabled Use the Trackpad to turn off the touch lock on the home screen. Screen is not being operated with bare fingers, for example gloves are being worn Bare fingers must make contact with the screen for correct operation. Alternatively you may use conductive gloves.
27.12 Miscellaneous troubleshooting Miscellaneous problems and their possible causes and solutions are described here. Problem Possible causes Possible solutions Display behaves erratically: Intermittent problem with power to the display. Check relevant fuses and breakers. • Frequent unexpected resets. • System crashes or other erratic behavior. Check that the power supply cable is sound and that all connections are tight and free from corrosion.
New a Series / New c Series / New e Series
Chapter 28: Technical support Chapter contents • 28.1 Raymarine customer support on page 288 • 28.
28.1 Raymarine customer support 28.2 Third-party support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and email. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Contact and support details for third-party suppliers can be found on the appropriate websites. Web support Navionics www.navionics.
Chapter 29: Technical specification Chapter contents • 29.
29.1 Technical specification New a Series physical specifications Dimensions Dimensions • Width: 354 mm (13.94 in.) • Width: 163.57 mm (6.44 in) • Height (NOT including bracket): 222 mm (8.74 in.) • Height (NOT including bracket): 143.47 mm (5.65 in) • Height (including bracket): 256 mm (10.08 in.) • Height (including bracket): 162.72 mm (6.41 in) • Depth (NOT including cables): 69 mm (2.72 in.) • Depth (NOT including cables): 74.1 mm • Depth (including cables): 160 mm (6.29 in.
e95 / e97 / e125 / e127 / c95 / c97 / c125 / c127 power specification e95 / e97 / c95 / c97 Display specification Size 9 in. Nominal supply voltage 12/24 V dc Type TFT backlit LED Operating voltage range 10.8V dc to 31.2V dc Color depth 24–bit Fuse / Breakers In-line fuse (fitted within power cable) Resolution 800 x 480 pixels (WVGA) • 7 A. (Standard 20 mm glass fuse) Viewing angle • Left / Right: 80 degrees Power consumption (at full brightness) • e95 / e97 / c95 / c97 = 16W Max.
Internal GPS specification Conformance specification The Internal GPS specification applies to the following multifunction displays New a Series, New c Series and New e Series (excluding the e165).
Chapter 30: Spares and accessories Chapter contents • 30.1 Transducer accessories on page 294 • 30.2 RayNet connector network cables on page 294 • 30.3 SeaTalkhs network cables on page 295 • 30.4 SeaTalkhs patch cables on page 295 • 30.5 Video cables on page 296 • 30.6 Power cables on page 296 • 30.7 a65 / a67 spares on page 297 • 30.8 e7 e7D spares on page 297 • 30.9 e95 / e97 / c95 / c97 spares on page 298 • 30.10 e125 / e127 / c125 / c127 spares on page 298 • 30.
30.1 Transducer accessories 30.2 RayNet connector network cables Item Part number Notes Cable Part number P48 sonar transducer A102140 Transom mount. A62360 P58 sonar transducer A102138 Transom mount. 1 m (3.28 ft) RayNet to SeaTalkhs (RJ45) cable 1 m (3.28 ft) Minn Kota transducer adaptor cable A62363 Only for direct connection to sonar variant multifunction display. 3 m (9.84 ft) RayNet to SeaTalkhs (RJ45) cable A80151 10 m (32.8 ft) RayNet to SeaTalkhs (RJ45) cable A80159 0.5 m (1.
30.3 SeaTalkhs network cables 30.4 SeaTalkhs patch cables Cable Part number Cable Part number 1.5 m (4.9 ft) SeaTalkhs network cable E55049 1.5 m (4.9 ft) SeaTalkhs patch cable E06054 5 m (16.4 ft) SeaTalkhs network cable E55050 5 m (16.4 ft) SeaTalkhs patch cable E06055 10 m (32.8 ft) SeaTalkhs network cable E55051 10 m (32.8 ft) SeaTalkhs patch cable E06056 SeaTalkhs E55052 20 m (65.6 ft) Spares and accessories network cable 15 m (49.2 ft) SeaTalkhs patch cable A62136 20 m (65.
30.5 Video cables 30.6 Power cables The following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays. Part number Description R70003 e-series accessory video cable 296 Notes Cable Part number 1.5 m (4.9 ft) Straight power and data cable R62379 1.5 m (4.
30.8 e7 e7D spares 30.7 a65 / a67 spares Item Part number R70147 Trunnion (bracket) mount kit A62358 Front bezel R70148 Documentation pack R62378 Suncover R70149 Flush mount panel set R62376 Power cable 1.
30.9 e95 / e97 / c95 / c97 spares Item Part number c/e series trunnion kit Item Part number R70001 c/e series trunnion kit R70002 c/e series front bezel R7004 c/e series front bezel R7006 c/e series suncover R70005 c/e series suncover R70007 c/e/ series rear bezel R70027 c/e/ series rear bezel R70028 c.e series gasket R70079 c.
30.
New a Series / New c Series / New e Series
Appendix A NMEA 0183 sentences The display supports the following NMEA 0183 sentences. These are applicable to NMEA 0183 and SeaTalk protocols.
Appendix B NMEA 2000 sentences The display supports the following NMEA 2000 sentences. These are applicable to NMEA 2000, SeaTalkng and SeaTalk 2 protocols.
Message number Message description Transmit Receive Bridge 130306 Wind data ● ● ● 130310 Environmental parameters ● ● ● 130311 Environmental parameters ● 130576 Small craft status ● 130577 Direction data 130578 Vessel speed components NMEA 2000 sentences ● ● ● ● 303
Appendix C Connectors and pinouts Pin Signal Power, data, and video connector 9 Screen 10 Not connected 4 9 1 8 10 2 Note: Use only Raymarine RayNet cables when connecting SeaTalkhs devices. 7 11 3 6 5 SeaTalkng connector D12186-1 Item Remarks Identification PWR / NMEA / Video Connector type 11 pin twist-lock Current source to network No current sourced for external devices Current sink from network • PSU: Main Power input. 6 • Video: No power required for interface.
Appendix D Software releases Raymarine regularly updates its multifunction display software to introduce improvements, additional hardware support and user interface features. The table below details some of the important enhancements and which software revision they were introduced with. Software version Applicable product manual V5.
Software version Applicable product manual Multifunction displays compatibility Changes • Corrected the ability to select Tide and/or Current Station uisng the Find Nearest feature. • Added NMEA 0183 & SeaTalkng data monitors to the diagnostics features. • Increased touch area for Alarm pop-ups and Back buttons. V2.xx 81337–1 c95 / c97 / c125 / c127 / e7 / e7D / e95 / e97 / e125 / e127 • Cartography redraw performance has been improved when sharing cartography via the SeaTalkhs/RayNet network.
www.ra ym a rin e .
