Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
Chapter 2: Installation 1 ST80 Autopilot Keypad Operation Manual resp disp trac k -1 +1 -10 +10 stan dby auto aut opi lot
ST80 Autopilot Keypad Operation Manual Package Contents 1. Autopilot keypad 2. Thumb nuts (2) 3. Threaded fixing studs (2) 4. White sun cover 5. SeaTalk cable 6. Installation template 7. Operation manual 8. Warranty card 9. Operation cue card 10.
2 ST80 Autopilot Keypad Operation Manual Contents Chapter 1: Introduction .............................................................. 3 1.1 Introduction .................................................................. 3 Chapter 2: Operation ................................................................. 4 2.1 Keypad Layout and Features ......................................... 4 2.2 Basic Operating Principles and Hints .............................. 5 Auto and Standby ............................
3 ST80 Autopilot Keypad Operation Manual Chapter 1: Introduction 1.1 Introduction The Autopilot keypad provides autopilot control via a simple ninekey interface. There are buttons for engaging and disengaging the pilot (auto and standby), course adjustment (-1, +1, -10 and +10), track control, response and direct entry to the autopilot display’s of a Masterview display head (disp).
4 ST80 Autopilot Keypad Operation Manual Chapter 2: Operation 2.1 Keypad Layout and Features The autopilot keypad has been designed as a control interface for Autohelm autopilot’s. The keypad consists of nine push-button keys together with operation status LED’s. The basic function of each of these keys is described in the following illustration.
ST80 Autopilot Keypad Operation Manual 5 • When the system is switched on the autopilot is always in STANDBY mode. • The display and lamp key only cycles pilot pages when the pilot chapter is open. 2.2 Basic Operating Principles and Hints Auto and Standby Autopilot operation has been simplified to a set of push-button keys, all of which are confirmed by a beep or beeps. Engaging the autopilot could not be easier.
6 ST80 Autopilot Keypad Operation Manual Track Advance/Acceptance If your navigation receiver is transmitting waypoint number and bearing to waypoint, a waypoint alarm will sound whenever a new target waypoint is selected. The autopilot maintains the current heading and automatic track control is suspended. Check the new bearing to waypoint, make sure that it is safe to turn, and then return to automatic track control by simply pressing the track key.
7 ST80 Autopilot Keypad Operation Manual 2.3 Additional Autopilot Features for Sailing Vessels Autotack When the autopilot is in compass or windvane mode, the following key command selects autotack mode. -1 resp disp track Press these keys together momentarily to begin a tack turning to port. -10 -1 +1 -10 +10 +1 standby auto +10 Press these keys together momentarily to begin a tack turning to starboard. autopilot D2428-1 This mode starts a tack routine so that you can tend to the sheets.
8 ST80 Autopilot Keypad Operation Manual In gusty conditions, always sail a few degrees off of the wind and pay frequent attention to sail trim and helm balance, using the rudder angle display on a Masterview display head. Generally speaking, performance will be improved by reefing the headsail and mainsail a little early rather than too late. 2.4 Keypad Illumination The keypad illumination can be adjusted as follows: Press for 1 second to enter illumination adjustment mode.
9 ST80 Autopilot Keypad Operation Manual 2.6 Important Safety Information The following rules should ALWAYS be observed when passage making under autopilot control: Maintain a permanent watch and regularly check all around for other vessels and obstacles – no matter how clear the sea may appear to be, dangerous situations can develop in minutes. Maintain an accurate log of your vessels position by visual bearings or radio/satellite position fixes.
10 ST80 Autopilot Keypad Operation Manual Chapter 3: EMC and Servicing Guidelines 3.1 Important information All Autohelm equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but good installation is required to ensure that performance is not compromised.
ST80 Autopilot Keypad Operation Manual 11 3.3 Check Before Going to Sea • Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc.. • In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not damage the equipment but can lead to it resetting, or momentarily may result in faulty operation. 3.
12 ST80 Autopilot Keypad Operation Manual Chapter 4: Specification Dimensions: 110 x 68 x 17mm (4.33 x 2.67 x 0.66in) Power supply: 10 to 16V DC Current consumption: Less than 240mA with illumination fully on, and less than 90mA at the courtesy level.
4 Raymarine Ltd. Anchorage Park, Portsmouth, P03 5TD, England.