Ray260 000 Installation and operation instructions English Date: 1 1-2013 Document number: 81343-3-EN © 2013 Raymarine UK Limited 0
Trademark and patents notice Autohelm, hsb2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalkNG, SeaTalkHS and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.
Contents Chapter 1 Important information........................ 7 Chapter 7 Digital selective calling (DSC)........... 41 Making a distress call................................................. 7 Making a Mayday call ................................................ 7 7.1 Digital Selective Calling (DSC) .............................. 42 7.2 Distress calls ....................................................... 43 Safety notices............................................................
Appendix B NMEA 2000 sentences ................... 82 Appendix C VHF Channels ................................. 83 Appendix D Phonetic alphabet........................... 90 Appendix E Prowords .........................................
Chapter 1: Important information Certified Installation Making a distress call In an emergency you can use your product to make an automatic DSC distress call. 55 60 5 10 50 15 45 20 40 35 30 25 0 0 0 0 0 0 0 0 0 RX HI RX HI DIS TRESS UNDESI GNATED ...3 COUNTI NG DOWN DIS TRESS UNDESI GNATED OK RX HI RX HI DIS TRESS UNDESI GNATED ...2 COUNTI NG DOWN DIS TRESS AWAITI NG ACK... REMAINING TI ME TO RESEND..04'20 RX HI RX HI DIS TRESS UNDESI GNATED ...
Caution: Power supply protection When installing this product ensure the power source is adequately protected by means of a suitably-rated fuse or automatic circuit breaker. Caution: Perform regular radio checks Perform regular radio checks when using your vessel, as recommended in radio training and certification schemes and radio equipment rules of use. Caution: Ensure proper radio use Under no circumstances should a DSC distress alert be sent from your radio for test purposes.
Modulation FM Frequency range 155.000 MHz to 165.000 MHz Maritime Mobile Service Identity (MMSI) This product is a class “D” Digital Selective Calling (DSC) device. A 9 digit MMSI number is required to operate DSC equipment. In some areas, a radio operator license is required before an MMSI number can be issued. Note: You can request an MMSI number from the same agency that issues radio or ship radio licenses in your area.
IMO and SOLAS The equipment described within this document is intended for use on leisure marine boats and workboats not covered by International Maritime Organization (IMO) and Safety of Life at Sea (SOLAS) Carriage Regulations. Technical accuracy To the best of our knowledge, the information in this document was correct at the time it was produced. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain.
Chapter 2: Document and product information Chapter contents • 2.1 Handbook information on page 12 • 2.
2.1 Handbook information 2.2 Product information This handbook contains important information regarding your DSC VHF Radio. The Ray260 is a Class D Digital Selective Calling (DSC) VHF radio. DSC enables you to make a selective call to a specific radio, and to transmit and receive position information to and from the selected radio. DSC also allows transmission of a distress alert to all radios within range at the touch of a button.
Chapter 3: Planning the installation Chapter contents • 3.1 System integration on page 14 • 3.2 Typical systems on page 15 • 3.3 Installation checklist on page 16 • 3.4 Schematic diagram on page 16 • 3.5 System protocols on page 17 • 3.
3.1 System integration Your VHF radio can be connected to the following marine electronics devices.
3.2 Typical systems The Ray260 can be installed as a standalone radio with peripherals or as part of a marine electronics network. Standalone DSC VHF radio system 1 2 4 3 0 5 D12614-3 1. Ray260 base station 2. Handset 3. Handset extension cable 4. Handset adaptor cable 5.
Extended system 1 0 2 5 4 3 INTCM 6 0 7 SeaTalkng 8 INTCM 10 INTCM 0 9 D1281 1-1 1. Station 1 active speaker 2. Station 1 handset 3. Ray260 base station 4. Loud hailer 5. GPS receiver 6. Station 2 active speaker 7. Station 2 handset 8. Station 3 handset 9. Station 3 passive speaker 10. Multifunction display Note: Each station can support connection of 1 passive OR 1 active speaker. 3.3 Installation checklist 3.
3.5 System protocols 3.6 Parts supplied Your product can send and receive position information, e.g. latitude and longitude using any of the following protocols: The parts supplied with your Ray260 are shown below. 1 • SeaTalkng 2 3 • NMEA 2000 0 • NMEA 0183 Using these protocols enables your radio to send position information to other devices in your system whenever it receives: 4 5 • a response to a DSC position request.
Ray260
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 20 • 4.2 Connections overview on page 20 • 4.3 Power connection on page 21 • 4.4 NMEA 0183 connection on page 22 • 4.5 Loud hailer connection on page 22 • 4.6 Handset connection on page 23 • 4.7 Passive speaker connection on page 23 • 4.8 Active speaker connection on page 24 • 4.
4.1 General cabling guidance 4.2 Connections overview Cable types and length The connections shown below are available on the Ray260 Base station. It is important to use cables of the appropriate type and length • Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. 1 • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run.
4.3 Power connection Sharing a breaker The power supply should be connected as shown below: Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. - + 1 1 2 3 4 2 3 6 12 v dc + 7 12 v dc - 5 6 8 4 4 D12612-2 1. Ray260 base station D11637-2 2. Power cable 1 Positive (+) bar 3. Vessel power supply 2 Negative (-) bar 4.
4.4 NMEA 0183 connection 4.5 Loud hailer connection The NMEA 0183 wires on the power/data cable can be used to connect the radio to a GPS receiver or a Raymarine multifunction display. A single 30 watt loud hailer can be connected to the base station via the loud hailer wires on the power / data cable. Note: Connections cannot be made using SeaTalkng and NMEA 0183 at the same time.
4.6 Handset connection 4.7 Passive speaker connection Up to 3 stations can be connected to the unit. A passive speaker can be connected to the handset cable using the external speaker pigtail wires. A station must include a handset and can include a passive or an active speaker. A handset must be connected to the station 1 port (HS1), this handset has priority over other connected handsets.
4.8 Active speaker connection 4.9 SeaTalkng connection An active speaker can be connected using the handset cable or handset extension cable. The Ray260 can interface with Raymarine GPS receivers and Raymarine multifunction displays using the SeaTalkng connector. 0 A Raymarine SeaTalkng GPS receiver cannot be connected directly to the Base station as GPS receivers are powered via the SeaTalkng backbone.
Chapter 5: Location and mounting Chapter contents • 5.1 General location requirements on page 26 • 5.2 Base station dimensions on page 27 • 5.3 Base station mounting on page 28 • 5.4 Speaker mounting on page 28 • 5.
5.1 General location requirements Power supply When selecting a location for the unit it is important to consider a number of factors. Select a location that is as close as possible to the vessel’s DC power supply. This will help to keep cable runs to a minimum. Antenna mounting and EME exposure Ensure that the antenna is connected to the radio before transmission. Raymarine declares a Maximum Permissible Exposure (MPE) radius of 1.5 metres (4.
A 0 B C G The dimensions of the Ray260 base station are shown below. A B 5.2 Base station dimensions C D E F D D12607-1 D12606-1 A 112 mm (4.4 in) B 112 mm (4.4 in) C 20.3 mm (0.799 in) D 15.55 mm (0.61 in) A 269.5 mm (10.6 in) E 25 mm (0.98 in) B 168 mm (6.6 in) F 30 mm (1.18 in) C 66.12 mm (2.6 in) G 91.5 mm (3.6 in) D 80.0 mm (3.15 in) Handset dimensions The dimensions of the handset are shown below. C B A D 0 INTCM 0 0 D12609-2 A 65.4 mm (2.57 in) B 154.
5.3 Base station mounting 5.4 Speaker mounting In order to mount the Ray260 base station follow the steps below. In order to mount a passive or active speaker follow the steps below. Note: Raymarine recommends mounting the unit vertically. 1 2 3 0 D12608-1 D12242-1 1. Check the selected location for the unit, a clear flat area with suitable clearance for air ventilation around the unit is required. 2. Secure the Base station mounting template in the chosen location using adhesive tape. 3.
5.5 Handset mounting 5. Hold the clip in place and secure using the screws provided. 6. Pull the connector end of the cable through the hole in the mounting panel. In order to mount the handset clip follow the steps below. 0 Note: The handset extension cable includes a speaker cable. If you are not connecting an external passive speaker then cover the speaker cable with waterproof tape or sealant to prevent corrosion. 0 1.
Ray260
Chapter 6: Getting started Chapter contents • 6.1 Controls on page 32 • 6.2 Switching the radio on on page 32 • 6.3 Switching the radio off on page 33 • 6.4 Voltage detection on page 33 • 6.5 Handset display LCD overview on page 34 • 6.6 Entering your MMSI number on page 35 • 6.7 Entering your ATIS ID on page 36 • 6.8 Selecting NMEA 0183 or SeaTalkng connection on page 37 • 6.9 Regional programming on page 37 • 6.10 Adjusting the LCD backlight level on page 38 • 6.
6.1 Controls 6.2 Switching the radio on You can access all functions, with the exception of adjusting the active speaker volume, from the handset. To power the radio on using any connected handset follow the steps below. Ray260 / Ray 260 AIS With the power off: 1. Press the red 16/9 / 16 PLUS button. The radio will power up and the radios MMSI number is displayed on-screen for approximately 3 seconds before displaying the main screen.
6.3 Switching the radio off 6.4 Voltage detection To switch the radio off follow the steps below. The radio detects the power supply voltage and a warning is displayed if the supply voltage is under or over recommended power. With the radio switched on: 1. Press and hold the 16/9 button for 5 seconds. An over voltage warning is displayed if the radio’s supply voltage is between 15.7 V dc and 16.0 V dc. The radio will automatically power down if the supply voltage exceeds 16.
6.5 Handset display LCD overview change request. Applies to Distress and All ships Urgency calls only. The information below describes the on-screen characters and icons which the radio displays on the main screen and what they mean. 1 2 3 RX TX HI LO ATIS SAVED LOCAL FAV123 4 I NT 6 7 8 DUP A 0016 DL WATCH 0009 5 M8 2 ° 3 4 .5 N 1 2 3 ° 4 5 .6 W AM0 1 :2 3 UT 0028A (Satellite icon) — Indicates that positional data is available from your GPS.
6.6 Entering your MMSI number Menu screen overview The radio’s menu options can be viewed on-screen. To program your radio with your MMSI number follow the steps below.
6.7 Entering your ATIS ID Enabling / Disabling the ATIS function To program your radio with your ATIS ID follow the steps below. With the ATIS ID programmed you can now enable or disable the ATIS function as required by following the steps below.
6.8 Selecting NMEA 0183 or SeaTalkng connection SeaTalkng The type of connection in use must be selected (i.e. or NMEA 0183). 1. Press and release the DSC Menu button. The main menu is displayed. 2. Select Connection. 3. Select Interface. 4. Select the required connection: i. Select NMEA 2000 if you are connected to a network or device using the SeaTalkng connector, or ii. Select NMEA 0183 if you are connected to a device using the NMEA 0183 connection. 5.
6.10 Adjusting the LCD backlight level 6.11 Adjusting the LCD contrast The LCD’s backlight level can be adjusted by following the steps below. 1. Press and release the MENU / DSC button to display the main menu. 2. Select SYSTEM CONFIG. 3. Select BACKLIGHT. The backlight level is displayed. 4. Use the Channel Up and Channel Down buttons or the Left Arrow and Right Arrow soft buttons to adjust the backlight to the required level. 5. Select Ok to confirm the new backlight level.
6.12 Changing the transmit power 6.13 GPS setup You can change the power level at which the radio transmits at by following the steps below. 1. Press and release the MENU / DSC button to display the main menu. 2. Select VHF OPERATION. 3. Select HI/LO POWER. 4. Select the HI/LO soft button to switch between high and low power. When connected to a GPS receiver over NMEA 0183 or SeaTalkng, the radio can display relevant GPS information.
Setting time format and offset You can select the time format and whether an offset is applied to the time. From the GPS setup menu (Main menu > GPS SETUP): 1. Select SETTING. 2. Select TIME OFFSET or TIME FORMAT as required. 3. Use the Channel Up and Channel Down buttons to cycle through the available values. 4. Select OK to confirm. Selecting stations to display 6.
Chapter 7: Digital selective calling (DSC) Chapter contents • 7.1 Digital Selective Calling (DSC) on page 42 • 7.2 Distress calls on page 43 • 7.3 Urgency calls on page 45 • 7.4 Safety calls on page 46 • 7.5 Routine calls on page 46 • 7.6 Group calls on page 47 • 7.7 Position requests on page 48 • 7.8 Position tracking on page 48 • 7.9 Test calls on page 49 • 7.10 Voice mail on page 49 • 7.11 Received call logs on page 50 • 7.12 Phonebook on page 50 • 7.
7.1 Digital Selective Calling (DSC) Routine calls Traditional VHF radio systems require users to listen until someone speaks, and then determine whether the call is for them. DSC ensures that calls are received by alerting or announcing the intended recipient(s) first so they are ready to listen to the subsequent message on the relevant channel.
7.2 Distress calls Making a distress call Making a designated distress call In an emergency you can use your product to make an automatic DSC distress call. When making a distress call you can specify the nature of the distress and if you do not have a valid GPS position available you can specify coordinates.
1. Press the Cancel soft key. A warning is displayed to inform the user that they are about to send a ‘Distress cancel call’. 2. Press the Send soft key. The ‘Distress cancel call’ is sent. 3. Press the OK soft key. 4. Make a broadcast to all stations giving your vessel’s name, call sign and MMSI number and cancel the false distress alert Example: “All, Stations, All Stations, All Stations. This is , , , . Cancel my distress alert of ,
Acknowledging a distress relay sent to your vessel 7.3 Urgency calls If a distress relay is specifically sent to your vessel this will be because the sender deems you to be in a position to assist in the rescue. The distress relay information is displayed on-screen. Making an urgency call HI HI DISTRESS] 00'01 RELAY FROM: 1234 56789 ORIG: 1122 33445 OK PAUSE P 1/5 HI HI DISTRESS] 00'02 RELAY UNDESIGNATED O LAT: 12 34.
7.4 Safety calls 7.5 Routine calls Making a safety call Individual calls can be made to ships and coast station contact saved in your phonebook or to any station by manually entering the stations MMSI number. A safety call should be used when there is an important navigational warning or meteorological forecast/broadcast. Safety alerts can also used for communications during search and rescue operations.
Making a routine DSC call You can use your product to make a routine DSC call to contact saved in the phonebook. 1. Press and hold the Menu DSC button for 3 seconds. The DSC menu is displayed. 2. Select Individual. The Manual option and the phonebook list is displayed. 3. Select a phonebook entry to make a DSC call to that contact, or 4. Select MANUAL to manually enter an MMSI number. 5. Use the Channel Up and Channel Down buttons to select a channel to transmit on. 6. Select OK. 7. Select SEND.
7.7 Position requests 7.8 Position tracking The radio can request position information from any station capable of responding to the request. The position tracking function enables regular position requests to be sent to selected target stations. The position data will be available on a Raymarine multifunction display connected over NMEA 0183 or SeaTalkng. Position requests can be sent to any contact stored in the phone book or by manually inputting the MMSI number of the station.
7.9 Test calls 7.10 Voice mail A Test Call feature is available for the purposes of testing your DSC VHF radio for correct operation. The radio includes a voice mail feature. The voice mail feature enables automated transmission of a pre-recorded message. There are 2 types of test call: A voice message up to 15 seconds long can be recorded, stored on the radio and then sent to a contact stored in the radio’s phonebook.
7.11 Received call logs 7.12 Phonebook All DSC calls received are logged in received call logs. The phonebook can be used to save up to 200 contacts. The following call types are recorded in the received call logs: You can add, edit and delete contacts stored in the phonebook.
7.13 Group list 7.14 DSC options Groups can be created to the MY GROUP ID list to enable group calling. DSC options can be set from the DSC options menu. Existing groups can be edited and deleted as required. AUTO CH CHANGE Adding a Group MMSI To make a group routine call you need to add a group MMSI number to your group list. You can store up to 20 group MMSI numbers on your radio. From the DSC Menu: 1. Select MY GROUP ID. 2. Select an empty entry e.g. [EMPTY 01]. 3.
Ray260
Chapter 8: VHF operations Chapter contents • 8.1 Scan mode on page 54 • 8.2 Watch modes on page 54 • 8.3 Priority channels on page 55 • 8.4 Favorite channels on page 55 • 8.5 Sensitivity on page 56 • 8.6 Private channels on page 56 • 8.7 Automatic Transmitter Identification System (ATIS) and Marcom-C mode on page 57 • 8.8 AIS on page 58 • 8.9 Voice recorder on page 58 • 8.
8.1 Scan mode 8.2 Watch modes Scan mode enables automatic searching for channels that are currently broadcasting. The watch modes monitor priority channels and the currently selected channel. Scan mode will search channels and stop when it finds a channel that is broadcasting. If the broadcast stops or is lost for more than 5 seconds then the scan will resume. There are 2 type of watch mode; Dual watch and Tri watch.
8.3 Priority channels 8.4 Favorite channels Channel 16 is the dedicated priority channel. Favorite channels can be saved to memory and assigned to the soft buttons during normal operation. The default secondary priority channel is channel 09, however this can be changed if required. Switching between priority channels 1. Press the Priority button to switch between the priority channels and the last used channel.
8.5 Sensitivity 8.6 Private channels The sensitivity level of the radio can be set to local mode or distant mode. The radio may be able to receive additional private channels depending on the country it is used in and whether the appropriate licenses are held. Local mode decreases the receiver sensitivity in high traffic areas to decrease unwanted reception. When in local mode LOCAL is displayed on-screen. Distant mode sets the receiver sensitivity to full.
8.7 Automatic Transmitter Identification System (ATIS) and Marcom-C mode Note: With the ATIS function enabled the following functions will be disabled: • DSC functions. ATIS is a European system used on some inland waterways. VHF radios operating in an ATIS region must be programmed with a unique ATIS number; this can be obtained from the relevant licensing authority.
8.8 AIS 8.9 Voice recorder The Ray260 AIS and Ray260E AIS have a built in AIS receiver. The radio includes a voice recorder function. With the built-in AIS receiver switched on AIS information can be sent to a connected Raymarine multifunction display using either the NMEA 0183 or SeaTalkng connections. The voice recorder enables automatic recording of up to 90 seconds of a received transmission. For transmissions over 90 seconds long, only the first 90 seconds is recorded.
8.10 System configuration The options available from the system configuration menu are shown below. BACKLIGHT Allows adjustment to the LCD’s backlight level. • OFF to HIGH in 10 increments. CONTRAST Allows adjustment to the LCD’s contrast level. • LOW to HIGH in 10 increments. KEY BEEP Allows adjustment of the beep heard when pressing handset buttons. • QUIET BEARING MODE Allows selection of bearing mode. • TRUE SPEED UNIT Allows selecting of preferred speed units.
Ray260
Chapter 9: Hailer, Fog horn, and Intercom Chapter contents • 9.1 Hailer on page 62 • 9.2 Fog horn on page 62 • 9.
9.1 Hailer 9.2 Fog horn The hailer function requires an optional loud hailer to be connected. The fog horn function requires an optional loud hailer to be connected. The hailer is an auxiliary function. When the hailer is active calls cannot be sent or received. The fog horn function can be set to manual or to a predefined automatic mode In hailer mode anything spoken into the handset is amplified and broadcast from the hailer, the message is not transmitted over the radio.
9.3 Handset intercom Installations that contain more than 1 handset can use the intercom feature. The intercom feature allows voice communication between connected handsets. The intercom call can be initiated from any handset. Using the intercom From the main menu: 1. Select HAILER/FOG/IC. 2. Select INTERCOM. A list of connected handsets is displayed. 3. Select the handset you want to call. 4. Wait for the handset station to acknowledge the call. 5. Press and hold the PTT button and speak your message.
Ray260
Chapter 10: Maintenance Chapter contents • 10.1 Maintenance on page 66 • 10.2 Routine checks on page 66 • 10.3 Cleaning on page 67 • 10.
10.1 Maintenance 10.2 Routine checks The Ray260 has no user serviceable parts or adjustments. Never remove the cover or attempt to service the product, doing so may invalidate your product warranty. The following periodic checks should be made: To following preventive measures should be followed: • Although the product is waterproof, keep the unit as dry as possible. • If you remove a handset connection ensure the dust cap is fitted to the connector.
10.3 Cleaning 10.4 Unit cleaning instructions Best cleaning practices. The unit does not require regular cleaning. However, if you find it necessary to clean the unit, please follow the steps below: 1. Ensure power is switched off. 2. Wipe unit clean with a damp cloth. 3. If necessary, use a mild detergent solution to remove grease marks. When cleaning this product: • Do NOT wipe the display screen with a dry cloth, as this could scratch the screen coating.
Ray260
Chapter 11: Troubleshooting Chapter contents • 11.1 Troubleshooting on page 70 • 11.
11.1 Troubleshooting The troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your product this section will help you to diagnose and correct problems in order to restore normal operation.
11.2 VHF Radio troubleshooting Problems with your VHF radio and their possible causes and solutions are described below: Radio will not power up. DSC functions are not working. Position data is not shown. Loose wiring connection. Check all cable connections. Blown fuse. Check fuse and replace if necessary. MMSI number not programmed. Check MMSI number has been entered correctly. Radio is set to ATIS mode. Use of DSC is not permitted in ATIS regions.
Ray260
Chapter 12: Technical support Chapter contents • 12.
12.1 Raymarine customer support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and e-mail. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Web support Please visit the customer support area of our website at: www.raymarine.
Chapter 13: Technical specification Chapter contents • 13.
13.
Chapter 14: Spares and accessories Chapter contents • 14.1 Ray260 Spares & Accessories on page 78 • 14.
14.1 Ray260 Spares & Accessories 14.2 SeaTalkng cables and accessories The following spares and accessories are available for the Ray260 VHF radio. SeaTalkng cables and accessories for use with compatible products. Description Part Number Description Part No Notes Ray260 handset US version with 10 m (32.8 ft.) adaptor cable A80196 SeaTalkng T70134 Includes: Ray260 handset US version with 20 m (65.6 ft.) adaptor cable A80249 Ray260 handset EU version with 10 m (32.8 ft.
Description Part No Notes SeaTalkng Inline terminator A80001 Provides direct connection of a spur cable to the end of a backbone cable. No T-piece required. SeaTalkng Blanking plug A06032 ACU / SPX SeaTalkng spur cable 0.3 m (1.0 ft) R12112 SeaTalk (3 pin) to SeaTalkng adaptor cable 0.4 m (1.3 ft) A06047 SeaTalk to SeaTalkng spur 1 m (3.3 ft) spur A22164 SeaTalk2 (5 pin) to SeaTalkng adaptor cable 0.4 m (1.
Ray260
Appendix A NMEA 0183 sentences The radio supports the following NMEA 0183 sentences.
Appendix B NMEA 2000 sentences The radio supports the following NMEA 2000 sentences. These are applicable to NMEA 2000 and SeaTalkng protocols.
Appendix C VHF Channels US Marine VHF Channels and Frequencies CH No. TX Freq RX Freq Single Freq Use 01A 156.050 156.050 x Port operations and commercial, VTS. Available only in New Orleans / Lower Mississippi area. 03A 156.150 156.150 x US Government only. Port operations or VTS in the Houston, New Orleans and Seattle areas. 05A 156.250 156.250 x 06 156.300 156.300 x Intership Safety. 07A 156.350 156.350 x Commercial. 08 156.400 156.400 x Commercial (Intership only).
CH No. TX Freq RX Freq Single Freq Use 73 156.675 156.675 x Port operations. Port operations. 74 156.725 156.725 x 77 156.875 156.875 x Port operations (Intership only). 78A 156.925 156.925 x Non-commercial. 79A 156.975 156.975 x Commercial. Non-commercial in Great Lakes only). 80A 157.025 157.025 x Commercial. Non-commercial in Great Lakes only). 81A 157.075 157.075 x US Government only — Environmental protection operations. 82A 157.125 157.
CH No. TX Freq RX Freq Area of operation 09 156.450 156.450 AC Intership, ship/shore, commercial, non-commercial and ship movement. Maybe used to communicate with aircraft and helicopters in predominantly maritime support operations. 10 156.500 156.500 AC, GL Intership, ship/shore, commercial, non-commercial, safety and ship movement. May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations. 11 156.550 156.
CH No. TX Freq RX Freq Area of operation 64A 156.225 156.225 EC 65A 156.275 156.275 Intership, ship/shore, commercial, non-commercial and safety. Search and rescue and antipollution operations on the Great Lakes. Towing on the Pacific coast. Port operations only in the St. Lawrence river area limited to 1 watt maximum power. Pleasure craft in the inland waters of Alberta, Saskatchewan and Manitobs (excluding Lake Winnipeg and the Red River. 66A 156.325 156.
CH No. TX Freq RX Freq Area of operation Use 87 157.375 161.975 AC, GL, NL Ship/shore and public correspondence. 88 157.425 162.025 AC, GL, NL Ship/shore and public correspondence. Area of operation • AC — Atlantic Coast, Gulf and St. Lawrence River up to and including Montreal. • EC — East Coast: includes NL, AC, GL and Eastern Arctic areas. • GL — Great Lakes: includes St. Lawrence above Montreal. • NL — Newfoundland and Labrador. • PC — Pacific Coast.
CH No. TX Freq RX Freq 28 157.400 162.000 Public correspondence, Port operations and Ship movement. 60 156.025 160.625 Public correspondence, Port operations and Ship movement. 61 156.075 160.675 Public correspondence, Port operations and Ship movement. 62 156.125 160.725 Public correspondence, Port operations and Ship movement. 63 156.175 160.775 Public correspondence, Port operations and Ship movement. 64 156.225 160.825 Public correspondence, Port operations and Ship movement.
Private Channels (Europe only) Country Channel Designations TX Freq RX Freq Channel Use Belgium 96 162.425 162.425 Marina Denmark L1 155.500 155.500 Pleasure L2 155.525 155.525 Pleasure L1 155.500 155.500 Pleasure L2 155.525 155.525 Pleasure L3 155.650 155.650 Pleasure Holland (Netherlands) 31 157.550 162.150 Marina 37 157.850 157.850 Leisure Denmark, Finland, Norway & Sweden F1 155.625 155.625 Fishing F2 155.775 155.775 Fishing F3 155.825 155.
Appendix D Phonetic alphabet To help make call letters more clearly understood, and to assist in spelling out similar sounding or unfamiliar word, radiotelephone users employ the international phonetic alphabet.
Appendix E Prowords Prowords can be used to simplify and speed up radio communications. Proword Meaning ACKNOWLEDGE Have you received and understood? CONFIRM Is that correct? CORRECTION An error has been made? I SAY AGAIN I repeat (e.g. important information). I SPELL Phonetically spelling of the word. OUT End of communication. OVER I have completed this part of the message and am inviting you to reply. RECEIVED Receipt acknowledgement. SAY AGAIN Repeat your message.
Ray260
www.ra ym a rin e .
