Operation Manual
Table Of Contents
- Ray54E Marine VHF Radio
- About this Handbook
- Important Information
- Maritime Mobile Service Identity (MMSI)
- Automatic Transmitter Identification System (ATIS)
- SAFETY NOTICE
- Contents
- About this Handbook iii
- Important Information iv
- Chapter 1: Introduction 1
- Chapter 2: Installation 3
- Chapter 3: Getting Started 9
- Chapter 4: General Operations 17
- 4.1 Turning the Power ON and OFF 17
- 4.2 Setting the Volume 17
- 4.3 Setting the Squelch 17
- 4.4 Setting the Power Output 17
- 4.5 Setting the Channel 18
- 4.6 Selecting a Weather Channel (If Available) 19
- 4.7 Selecting the Priority Channel 20
- 4.8 Selecting the Secondary Priority (PLUS) Channel 21
- 4.9 Transmitting 23
- 4.10 Using the Scan Modes 23
- 4.11 Adding Channels to Memory 26
- 4.12 Using the Monitor Modes 27
- 4.13 USER Channel Mode 29
- 4.14 DSC Call Operation 29
- 4.15 Menu Mode Operation 30
- Chapter 5: Digital Selective Calling (DSC) 31
- Chapter 6: Menu Settings 57
- Chapter 7: Customer Service 85
- Appendix A: Specifications 87
- Appendix B: Channel List 89
- Appendix C: Glossary 101
- Index 103
- Chapter 1: Introduction
- Chapter 2: Installation
- Chapter 3: Getting Started
- 3.1 Keypad and Rotary Knobs
- 3.2 LCD Display
- 1. (HI/LO) TX Power
- 2. (TX) Transmitting
- 3. (RX) Receiving
- 4. (LOCAL) Local/Distant Mode
- 5. DSC Message
- 6. ATIS Active
- 7. NO GPS
- 8. Battery Low
- 9. (USER) Favourite Channel Mode
- 10. (SAVED) Memory Mode
- 11. (WX) Weather Channel
- 12. (ALERT) Weather Alert
- 13. (U I C) Channel Set
- 14. (A) Simplex Channel
- 15. (B) Receive-only Channel
- 16. Channel Number
- 17. Dot Matrix Display
- Chapter 4: General Operations
- 4.1 Turning the Power ON and OFF
- 4.2 Setting the Volume
- 4.3 Setting the Squelch
- 4.4 Setting the Power Output
- 4.5 Setting the Channel
- 4.6 Selecting a Weather Channel (If Available)
- 4.7 Selecting the Priority Channel
- 4.8 Selecting the Secondary Priority (PLUS) Channel
- 4.9 Transmitting
- 4.10 Using the Scan Modes
- 4.11 Adding Channels to Memory
- 4.12 Using the Monitor Modes
- 4.13 USER Channel Mode
- 4.14 DSC Call Operation
- 4.15 Menu Mode Operation
- Chapter 5: Digital Selective Calling (DSC)
- Chapter 6: Menu Settings
- Chapter 7: Customer Service
- Appendix A: Specifications
- Appendix B: Channel List
- Appendix C: Glossary
- Index
Chapter 5: Digital Selective Calling (DSC) 37
Receiving Individual Calls
When an Individual Call is received, the radio sounds an alert tone and
displays the type of call, the name or MMSI number (if the caller’s MMSI
number has not been programmed into your Phonebook) of the caller and the
time the call was initiated. When an Individual Call from a station is received,
the radio may also ask you to send an acknowledge (ACK) back to the caller.
You are prompted to accept or decline the call.
➤ To silence the alert tone:
Press any key. Automatic cancellation takes place after 2 minutes.
➤ To cancel the mode without sending ACK:
Press the CLEAR key. The alert tone is muted, the Individual Call is
interrupted and the normal screen appears on the display.
➤ To accept the Individual Call:
Push the CH knob. The tone is muted (if you have not already pressed another
key) and an acknowledge (if requested) is sent to the originating station.
The LCD indicates a change of working channels has been made.
For Routine Calls, the channel changes to the one designated by the caller.
For Safety and Urgency Calls, the radio automatically switches to channel
16.