Operation Manual
Table Of Contents
- Ray54E Marine VHF Radio
- About this Handbook
- Important Information
- Maritime Mobile Service Identity (MMSI)
- Automatic Transmitter Identification System (ATIS)
- SAFETY NOTICE
- Contents
- About this Handbook iii
- Important Information iv
- Chapter 1: Introduction 1
- Chapter 2: Installation 3
- Chapter 3: Getting Started 9
- Chapter 4: General Operations 17
- 4.1 Turning the Power ON and OFF 17
- 4.2 Setting the Volume 17
- 4.3 Setting the Squelch 17
- 4.4 Setting the Power Output 17
- 4.5 Setting the Channel 18
- 4.6 Selecting a Weather Channel (If Available) 19
- 4.7 Selecting the Priority Channel 20
- 4.8 Selecting the Secondary Priority (PLUS) Channel 21
- 4.9 Transmitting 23
- 4.10 Using the Scan Modes 23
- 4.11 Adding Channels to Memory 26
- 4.12 Using the Monitor Modes 27
- 4.13 USER Channel Mode 29
- 4.14 DSC Call Operation 29
- 4.15 Menu Mode Operation 30
- Chapter 5: Digital Selective Calling (DSC) 31
- Chapter 6: Menu Settings 57
- Chapter 7: Customer Service 85
- Appendix A: Specifications 87
- Appendix B: Channel List 89
- Appendix C: Glossary 101
- Index 103
- Chapter 1: Introduction
- Chapter 2: Installation
- Chapter 3: Getting Started
- 3.1 Keypad and Rotary Knobs
- 3.2 LCD Display
- 1. (HI/LO) TX Power
- 2. (TX) Transmitting
- 3. (RX) Receiving
- 4. (LOCAL) Local/Distant Mode
- 5. DSC Message
- 6. ATIS Active
- 7. NO GPS
- 8. Battery Low
- 9. (USER) Favourite Channel Mode
- 10. (SAVED) Memory Mode
- 11. (WX) Weather Channel
- 12. (ALERT) Weather Alert
- 13. (U I C) Channel Set
- 14. (A) Simplex Channel
- 15. (B) Receive-only Channel
- 16. Channel Number
- 17. Dot Matrix Display
- Chapter 4: General Operations
- 4.1 Turning the Power ON and OFF
- 4.2 Setting the Volume
- 4.3 Setting the Squelch
- 4.4 Setting the Power Output
- 4.5 Setting the Channel
- 4.6 Selecting a Weather Channel (If Available)
- 4.7 Selecting the Priority Channel
- 4.8 Selecting the Secondary Priority (PLUS) Channel
- 4.9 Transmitting
- 4.10 Using the Scan Modes
- 4.11 Adding Channels to Memory
- 4.12 Using the Monitor Modes
- 4.13 USER Channel Mode
- 4.14 DSC Call Operation
- 4.15 Menu Mode Operation
- Chapter 5: Digital Selective Calling (DSC)
- Chapter 6: Menu Settings
- Chapter 7: Customer Service
- Appendix A: Specifications
- Appendix B: Channel List
- Appendix C: Glossary
- Index
66 Ray54E VHF Radio
6. Push in the CH knob to accept and move onto UTC time. Select the time
characters in the same manner.
Note: You must enter the TIME parameter in UTC time and not in local time.
When time data is entered manually, the NO GPS indicator remains
illuminated and the UTC designator appears following the time.
Note: When the final selection is made the radio returns to the previous
Menu Selection. To exit this sub-mode, select BACK or else press the 16/
PLUS or CLEAR keys.
6.6 Settings
You can also set how some time and position information is displayed on the
screen:
• whether Lat/Lon data is displayed
• whether the Time is displayed
• whether a Time Zone Offset is used
• how the Time data is formatted
• whether COG/SOG data is displayed
➤ To adjust these Settings:
1. Press and hold the CALL/MENU key to enter Menu mode.