User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
4265.DOC020102
2-186
Edition July 2015
2.6.4 Zone Usage
An ARPA ZONE created on selected MFC console displays in continuous line
and yellow color (active ARPA ZONE). Targets arriving this ARPA ZONE will be
acquired on this MFC console.
The same ARPA ZONE displays on the other MFC in yellow color and dashed
lines (passive ARPA ZONE). Targets arriving this ARPA ZONE will not be
acquired.
ZONE USAGE allows the operator to use this ARPA ZONE on another MFC
console.
The operator can activate or edit the ARPA ZONE on the local MFC console.
Operator controls
Task
Step 1 Open the TGT menu.
Step 2 Pressing the ZONE USAGE soft button the menu
USE ZONE BY ARPA TRACKER appears.
Step 3 Select the ARPA ZONE and press the right
trackball button to enable the ZONE.
The menu changes.
Step 4 Pressing the OK soft button the ARPA ZONE
presentation changes from dashed lines to a continues
line. The ARPA ZONE is activated. It is possible to edit
this zone (chapter 2.6.2). The new zone form appear on
all MFC consoles if selected.
For deactivating this ARPA ZONE follow Step 1 to Step 3
again.
Step 5 Pressing the OK soft button APRA ZONE
presentation changes from continues line to dashed lines.
The ARPA ZONE is deactivated.
If this ARPA ZONE is not used in the INS system the
ZONE will be fade out automatically.
For activating this ZONE again follow Step 1 to Step 4
again. In this case the ARPA ZONE is present on all MFC
consoles again.