User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
Edition July 2015
2-223
4265.DOC020102
2.11.2 Alarm Messages
The following ALARM table shows all possible alarm indications and first
proposal how to handle an ALARM message.
ALARM MESSAGE
a) Problem Description
b) Corrective Action
ANTENNA DOWNLINK
ERROR
(DOWN LINK ERROR
ALARM)
a) Antenna System is disturbed. An error
has occurred on the transceiver to the
display link.
b) Refer to maintenance section for
troubleshooting and repair.
ANTENNA SAFETY
(ANTENNA SAFETY
ALARM)
a) The antenna switch has been switched
to OFF.
b) Check the situation (chapter 2.12).
ANTENNA STOPPED
a) Antenna System is disturbed.
A signal from the transceiver/adapter
interface which indicates that the
antenna is not rotating.
b) Refer to the maintenance section for
troubleshooting and repair.
Call Service.
ANTENNA UPLINK ERROR
(UP LINK ERROR)
a) An error has occurred on the display to
the transceiver link.
b) Start the Radar System again.
Refer to the maintenance section for
troubleshooting and repair.
Call Service
CAN BUS ERROR
(Radar Transceiver CAN
BUS ERROR ALARM)
a) External alarm from Radar Transceiver.
b) Call Service.